Power Fist 8844078 Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire
V1.0 8844078
Please read and understand all instructions before use. Retain this manual for
future reference.
8844078 3/4 in. Impact Wrench V1.0
2 For technical questions call 1-800-665-8685
SPECIFICATIONS
Air Inlet 1/4 in.
Square Drive Size 3/4 in.
Working Pressure 90 PSI
Average CFM @ 15 Second Run Time 8.25 CFM
CFM @ Full Load 7.5 CFM
Max. Torque 500 ft-lb
Speed Rating 4,500 RPM
Min. Hose Size 3/8 in.
Material Die-cast Aluminum Housing
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A
notice is an alert that there is a possibility of property damage, injury or
death if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that
will result in severe personal injury or death if the proper
precautions are not taken.
WARNING! This notice indicates a specific hazard or unsafe practice that
could result in severe personal injury or death if the proper
precautions are not taken.
CAUTION! This notice indicates a potentially hazardous situation that
may result in minor or moderate injury if proper practices are
not taken.
NOTICE! This notice indicates that a specific hazard or unsafe practice
will result in equipment or property damage, but not personal
injury.
V1.0 3/4 in. Impact Wrench 8844078
Visit www.princessauto.com for more information 3
INTRODUCTION
The 3/4 in. Impact Wrench can loosen or tighten nuts and bolts with 500 ft-lb of
power. Power is controlled by the built-in-air regulator at the handles base.
SAFETY
WARNING! Read and understand all instructions before using this tool. The
operator must follow basic precautions to reduce the risk of personal injury
and/or damage to the equipment.
Keep this manual for safety warnings, precautions, operating or inspection
and maintenance instructions.
WORK AREA
1. Operate in a safe work environment. Keep your work area clean, well-lit
and free of distractions. Place lights so you are not working in a shadow.
2. Keep anyone not wearing the appropriate safety equipment away from
the work area.
3. Store unused tools properly in a safe and dry location to prevent rust
or damage. Lock tools away and keep out of the reach of children.
PERSONAL SAFETY
WARNING! Wear personal protective equipment approved by the Canadian
Standards Association (CSA) or American National Standards Institute (ANSI).
PERSONAL PROTECTIVE EQUIPMENT
1. Always wear impact safety goggles that provide front and side protection
for the eyes. Eye protection equipment should comply with CSA Z94.3-07
or ANSI Z87.1 standards based on the type of work performed.
2. The tool may contain high pressure. Use safety glasses and gloves for
protection during operation. Keep hands clear of the exposed rubber
portions of the hose.
3. Wear the appropriate type of full-face shield in addition to safety
googles, as the work can create chips, abrasive or particulate matter.
4. Wear protective clothing designed for the work environment and tool.
5. Wear the appropriate rated dust mask or respirator.
6. This tool can cause hearing damage. Wear ear protection gear to
eliminate or reduce the noise. If possible add a muffling device to the
air tools exhaust.
8844078 3/4 in. Impact Wrench V1.0
4 For technical questions call 1-800-665-8685
PERSONAL PRECAUTIONS
Control the tool, personal movement and the work environment to avoid
personal injury or damage to tool.
1. Do not operate any tool when tired or under the influence of drugs,
alcohol or medications.
2. Avoid wearing clothes or jewelry that can become entangled with the
moving parts of a tool. Keep long hair covered or bound.
3. Do not overreach when operating a tool. Proper footing and balance
enables better control in unexpected situations.
4. Securely hold this tool using both hands. Using a tool with only one
hand can result in loss of control.
5. Keep your fingers away from the trigger/switch while carrying the tool,
attaching an air hose or an accessory. Lock the trigger/switch safety if
available.
6. Avoid unintentional starts. Be sure that the regulator/throttle switch is
in the neutral or OFF position when not in use and before connecting it
to any air source.
7. Never point the air stream or tool at any point of your body, other
people or animals. Debris and dust ejected at high speed can cause an
injury.
8. Serious injury or death may occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles.
Never inhale compressed air directly from the pump or air tool.
SPECIFIC SAFETY PRECAUTIONS
WARNING! DO NOT let comfort or familiarity with product (gained from
repeated use) replace strict adherence to the tool safety rules. If you use
this tool unsafely or incorrectly, you can suffer serious personal injury.
1. Use the correct tool for the job. This tool was designed for a specific function.
Do not modify or alter this tool or use it for an unintended purpose.
2. Do not use the tool if any parts are damage broken or misplaced. Repair
or replace the parts.
3. Never hold the drive, socket, drive extension or accessories
during impacting. Doing so increases the risk of cuts, burns or
vibration injuries.
4. Hold the tool correctly; be ready to counteract normal or sudden
movements and have both hands available.
V1.0 3/4 in. Impact Wrench 8844078
Visit www.princessauto.com for more information 5
5. Do not use in confined spaces and beware of crushing your hands
between the tool and workpiece, especially when unscrewing.
6. The tool is not insulated against contact with live electrical conduits or
sources.
7. Do not over-tighten nuts. They could shatter and cause damage to the
tool or workpiece or cause serious injury. Use a torque wrench to
torque the nut after using the impact wrench.
8. This impact wrench should only be used with impact sockets and
extensions. Use of other accessories can cause them to break, which
could damage the unit or cause injury.
AIR TOOL PRECAUTIONS
1. Use only clean and dry compressed air as a power source.
Contaminated or moist air will gradually damage the tool.
2. Install an in-line shutoff valve or regulator to allow immediate control
over the air supply in an emergency, even if a hose is ruptured.
3. Discontinue tool use if it does not work properly or air is leaking. Tag
or mark the tool as defectiveor out of serviceuntil repaired.
4. Check the manufacturers maximum pressure rating for air tools and
accessories. Compressor outlet pressure must be regulated to never
exceed the maximum pressure rating of the tool (see Specifications).
Exceeding the maximum PSI rating can create a bursting hazard,
causing injury and property damage.
5. Attach all accessories properly to the tool before connecting the air
supply. A loose accessory may detach or break during operation.
6. Never use oxygen, combustible gas or any other bottled gas as a
power source. Any power source other than an air compressor could
cause an explosion and serious personal injury.
7. Turn OFF the valve and discharge any remaining air pressure after each
use or before adjusting the tool.
8. Do not leave the air tool unattended with its compressed air supply on.
Turn off the compressed air supply and bleed the air tool of any
remaining compressed air before leaving the air tool unattended.
9. Serious injury may occur from loose debris being propelled at high
speeds from the compressed air stream. Always wear OSHA approved
safety glasses to protect the eyes during operation of the air
compressor.
8844078 3/4 in. Impact Wrench V1.0
6 For technical questions call 1-800-665-8685
10. Always turn off the air compressor and drain tank pressure completely
before attempting maintenance or attaching air tools. Release pressure
slowly from the system.
11. Serious injury or death may occur from inhaling compressed air. The air
stream may contain carbon monoxide, toxic vapors or solid particles.
Never inhale compressed air directly from the pump or air tool.
POWER TOOL PRECAUTIONS
1. Do not use any power tool with a malfunctioning power switch or
control. A power tool that fails to respond to the controls is dangerous
and can cause an injury. A qualified technician must repair and verify
the power tool is operating correctly, before it can be used.
2. Disconnect the power source before installing or servicing the tool.
3. Never force the tool. Excessive pressure could break the tool, resulting
in damage to your workpiece or serious personal injury. Excessive
pressure is the cause if your tool runs smoothly under no load, but
roughly under load.
4. Keep hands and fingers away from the work area. Any part of body
contacting the tools working parts could cause an injury.
5. Only use accessories that are specifically designed for use with the
tool. Ensure the accessory is tightly installed.
6. Only use an accessory that exceeds the No Load Speed rating (see
Specifications).
7. Before using the tool on a workpiece, test the tool by running it at the
highest no load speed for at least 30 seconds in a safe position. Stop
immediately if there is any abnormal vibration or wobbling. Check the
tool to determine the cause.
8. Never touch the tool accessory or workpiece during or immediately after
use. They may be hot and could inflict a burn injury.
9. Never use a tool with a cracked or worn tool accessory. Change the
tool accessory before using it.
10. Do not place the tool down until the tools accessory has stopped
moving. The accessory may catch the surface of work material and
wrench itself free, causing injury to the user or others in the work area.
V1.0 3/4 in. Impact Wrench 8844078
Visit www.princessauto.com for more information 7
AIR HOSE PRECAUTIONS
1. Inspect the tool's air hose for cracks, fraying or other faults before
each use. Discontinue use if the air hose is damaged or hissing is heard
from the air hose or connectors. Replace the defective air hose.
2. Do not allow people, mobile equipment or vehicles to pass over the
unprotected air hose. Position the air hose away from high traffic
areas, in a reinforced conduit or place planks on both sides of the air
hose to create a protective trench.
3. Prevent damage to the air hose by observing the following:
a. Never carry the tool by the air hose.
b. Keep the air hose behind the tool and out of the tool's work path.
c. Keep the air hose away from heat, oil, sharp edges or moving parts.
d. Do not wrap the air hose around the tool as sharp edges may pierce
or crack the air hose. Gently coil the hose and either hang on a hook
or fasten with a device to keep hose together when storing.
4. A damaged or disconnected air hose under pressure may whip around and
inflict personal injury or damage the work area. Secure the compressor's
air hose to a fixed or permanent structure with clamps or cable ties.
COMPRESSOR/TANK PRECAUTIONS
DANGER! Do not use an air tank beyond its expiration date. A tank rupture
or explosion may kill or cause a serious injury to yourself or a bystander.
Disable and discard the air tank according to the your municipality by-laws.
1. Never drill into, weld, patch or modify the air tank. Immediately replace the
tank or compressor if an air leak develops. The leak may lead to a rupture.
2. Never make adjustments to the components that control tank pressure.
Serious injury or death may occur if modifications are made to the
pressure switch, safety relief valve or other components that control
the tank pressure.
3. Check operation of the pressure relief valve on a regular basis and
never operate without a factory approved pressure relief valve. Do not
make alterations to the factory operating pressure settings.
VIBRATION PRECAUTIONS
1. This tool vibrates during use. Repeated or long-term exposure to
vibration may cause temporary or permanent physical injury. Take
frequent breaks when using the tool.
8844078 3/4 in. Impact Wrench V1.0
8 For technical questions call 1-800-665-8685
2. If you feel any medical symptoms related to vibrations (such as
tingling, numbness, and white or blue fingers), seek medical attention
as soon as possible.
3. Wear suitable gloves to reduce the effects of vibration.
4. DO NOT use this tool before consulting a physician if one of the
following applies:
a. Pregnant
b. Impaired blood circulation to the
hands
c. Past hand injuries
d. Nervous system disorders
e. Diabetes
f. Raynaud's Disease
UNPACKING
WARNING! Do not operate the tool if any part is missing. Replace the
missing part before operating. Failure to do so could result in a malfunction
and personal injury.
Remove the parts and accessories from the packaging and inspect for damage.
Make sure that all items in the contents are included.
Contents: Impact Wrench Male Plug Hex Key
IDENTIFICATION KEY
A Square Drive Anvil
B Valve Stem
C Trigger
D Air Flow Regulator
E Air Inlet
ASSEMBLY & INSTALLATION
Letter references in parenthesis (A) refer to the included Identification Key.
INSTALL AIR CONNECTOR
Prepare a standard 1/4 in. NPT male air connector (sold separately) for use
with your tool.
1. Wrap the external threads of the male connector with sealant tape.
a. Wrap tape in a clockwise direction so it will not unravel.
V1.0 3/4 in. Impact Wrench 8844078
Visit www.princessauto.com for more information 9
b. Do not tape all the threads. Leave several leading threads
unwrapped for easier alignment.
2. Screw the connector into the tool's air inlet (E) and tighten with a
wrench until snug.
3. Run the compressor at a low volume and check the connection for air
leaks. Do not use the tool until all air leaks are repaired or the faulty
component is replaced.
IMPORTANT! Vibration may cause failure if a quick coupler is connected directly
to the air tool. To overcome this, connect a leader hose to the tool. A quick
coupler may then be used to connect the leader hose to the air line hose.
SOCKET INSTALLATION
WARNING! The torque of the impact wrench is 500 ft-lb. Make sure that the
nut or bolt you are using the tool to tighten can withstand the rated torque
and is rated for 4,500 RPM or greater. If available, check the recommended
torque specifications for the nut.
1. Turn off the air compressor and disconnect the air hose when changing
sockets.
2. Select the appropriately sized 3/4 in. drive impact socket for the job.
Only use impact sockets which are specifically designed for use with
an impact wrench. Do not use worn or damaged sockets.
3. Push and snap the socket (not included) onto the anvil (A).
4. Attach the air hose and turn the air compressor on.
OPERATION
WARNING! This tool generates considerable torque when in use. Always
hold the tool with both hands when using and brace yourself to resist the
torque which will be delivered to the workpiece.
Lubricate the rotor gears at the beginning of each day of use. See the
Lubricating Rotor Gears section.
1. Tighten the nut as far as you can by hand before using the impact
wrench.
2. Connect the impact wrench to the air hose.
3. Power is increased or decreased by adjusting the air flow with the
regulator (D) at the handles base.
8844078 3/4 in. Impact Wrench V1.0
10 For technical questions call 1-800-665-8685
a. Push the air flow regulator in to allow adjustments. The knob is
numbered 1 to 4, with 1 being the least powerful and 4 as the
most powerful.
b. Rotate the knob to align the number with the triangle inset in the
handle.
c. Fine tune the power by rotating the dial between two numbers.
4. Push the valve stem (B) out for forward (clockwise) and push the stem
in for reverse (counterclockwise).
a. Wait until the tools anvil has stopped rotating before switching to
the opposite direction.
5. Place the socket over the fastener, grip the impact wrench firmly with
both hands and gently squeeze the trigger. The impact wrench will
activate when the trigger is squeezed.
a. If the tool stalls while tightening, do not raise the output pressure
of the air compressor above 90 PSI. Pressure above 90 PSI will
strip the workpiece and damage the tool, potentially causing tool
failure and serious injury. Use other appropriate methods and
tools to tighten the nut.
6. This tool will stop operation/rotation a few seconds after the trigger is
released.
7. When the fastener is tightened, release the trigger and remove the tool
and socket.
8. Use a mechanical torque wrench to check the fastener torque.
9. When finished with the tool, turn off the air compressor, disconnect
the air hose and discharge any residual air remaining in the tool. Put
the impact wrench away in a safe storage area.
CARE & MAINTENANCE
1. Maintain the tool with care. A tool in good condition is efficient, easier
to control and will have fewer problems.
2. Inspect the tool fittings, alignment, hoses and power supply cord
periodically. Have damaged or worn components repaired or replaced
by an authorized technician. Only use identical replacement parts
when servicing.
3. Follow instructions for lubricating and changing accessories.
4. Only use accessories intended for use with this tool.
V1.0 3/4 in. Impact Wrench 8844078
Visit www.princessauto.com for more information 11
5. Keep the tool clean, dry and free from oil/grease at all times.
6. Maintain the tools labels and name plates. These carry important
information. If unreadable or missing, contact Princess Auto Ltd. for
replacements.
WARNING! Only qualified service personnel should repair the tool. An
improperly repaired tool may present a hazard to the user and/or others.
AIR TOOL LUBRICATION
NOTICE! Only use air tool oil to lubricate the tool. Other lubricants are not
suitable and will damage the tool or cause a malfunction during use.
NOTICE! Never use a penetrating oil to lubricate an air tool. Penetrating oil
acts as a solvent that will dissolve the tools grease packing and may
damage the o-rings, causing the tool to seize or malfunction.
1. All air tools have an internal coating of grease to prevent corrosion
during shipping and storage. Remove this grease by adding a generous
amount of air tool oil in the air inlet and then run the tool under no
load until the exhaust is clear.
2. Manually add a drop or two of air tool oil into the tools air inlet before
each use and after every hour of continuous use. The tool will not work
properly without lubrication and parts will wear prematurely.
3. Avoid adding too much air tool oil as this can cause premature power
loss and eventual tool failure. A qualified technician will need to take
the tool apart and clean out the excess oil.
4. Apply a generous amount of air tool oil to the tool before storing it for
an extended period of time (overnight, weekend, etc.). Run the tool for
approximately 30 seconds to ensure the oil is evenly distributed
throughout the tool. Store it in a clean and dry location.
LUBRICATING ROTOR GEARS AND IMPACT MECHANISM
Lubricate the rotor gears and impact mechanism before using at the
beginning of the day.
1. Remove the hex screw (Fig. 2) to the grease
opening and set aside.
2. Insert the grease gun nozzle into the opening
and squeeze out several drops of grease.
3. Replace the screw and tighten.
4. Run the tool without load for several seconds
to spread the grease.
Fig. 2
8844078 3/4 in. Impact Wrench V1.0
12 For technical questions call 1-800-665-8685
DISPOSAL
Recycle a tool damaged beyond repair at the appropriate facility.
Contact your local municipality for a list of disposal facilities or by-laws for
electronic devices, batteries, oil or other toxic liquids.
IMPORTANT! DO NOT pollute the environment by allowing uncontrolled
discharge of waste oil.
TROUBLESHOOTING
Visit a Princess Auto Ltd. location for a solution if the tool does not function
properly or parts are missing. If unable to do so, have a qualified technician
service the tool.
Problem(s) Possible Cause(s) Suggested Solution(s)
Tool runs at
normal speed, but
loses power under
load.
Motor parts worn.
1. Have a qualified technician
service the tool.
2. Replace tool or parts.
Tool runs slowly.
Air flows slightly
from exhaust.
Motor parts jammed
with dirt particles.
OR
Airflow blocked by
dirt.
1. Check air inlet filter for
blockage.
2. Pour air tool lubricating oil
into air inlet as per
lubrication instructions for
clearing shipping grease.
3. Operate tool in short bursts
to clear debris.
4. If tool still jammed, clean
tool and lubricate per
lubrication instructions.
Tool runs
slowly. Air flows
slightly from
exhaust.
1. Air regulator in
closed position.
2.
Damage or excessive
wearing of internal
parts.
1. Open the air regulator to
desired airflow.
2a. Have a qualified technician
service the tool.
2b. Replace tool or parts.
Tool will not
shut off.
1. Throttle valve o-ring
dislodged from inlet
valve seat.
2. Trigger mechanism
jammed or dirty.
1. Replace throttle valve
o-rings.
2. Clean trigger mechanism and
lubricate.
V1.0 3/4 in. Impact Wrench 8844078
Visit www.princessauto.com for more information 13
Problem(s) Possible Cause(s) Suggested Solution(s)
Loss of power
or erratic
performance.
1. Excessive drain on
the air hose
. Incorrect
size or type of hose
connectors.
2. Moisture or
restriction in the air
hose/tank
3. Air compressor has
insufficient flow.
1. Check the air hose and
confirm the hose fitting is
correct for the inlet
bushing.
2. Depressurize system and
drain tank and air hose of
water.
3. Ensure tool is connected to
a compressor with a rate
flow that matches the tool.
PARTS BREAKDOWN
PARTS LIST
# DESCRIPTION QTY
1 Protecting Rubber 1
2 Oil Seal 1
3 Housing 1
4 Screw 1
5 Anvil Bushing 1
6 Anvil Collar 1
7 O-Ring 1
8 Spacer 1
9 Anvil (3/4 in.) 1
8844078 3/4 in. Impact Wrench V1.0
14 For technical questions call 1-800-665-8685
# DESCRIPTION QTY
10 Hammer Pin 1
11 Hammer Dog 1
12 Drive Cam 1
13 Hammer Cage 1
14 Ball Bearing 1
15 Oil Seal 2
16 O-Ring 1
17 Front End Plate 1
18 Rotor Blade 6
19 Rotor 1
20 Cylinder 1
21 Rear End Plate 1
22 Ball Bearing 1
23 Rear Gasket
1
24 Rear Cover 1
25 Washer 3
26 Screw 3
27 Protecting Rubber 1
28 Washer 4
29 Screw 4
30 Valve Sleeve 1
31 Reverse Valve 1
32 Screw 1
33 Spring 1
34 Pin 1
35 Screw 2
36 Exhaust Deflector 1
37 Trigger 1
38 Screw 1
39 Pin 1
40 Pin 1
41 Bushing 1
42 Valve Stem 1
43 Ball Valve 1
44 Spring 1
45 Hose Adapter 1
46 Screen 1
47 O-Ring 1
48 Air Regulator 1
V1,0 8844078
Vous devez lire et comprendre toutes les instructions avant d'utiliser l'appareil.
Conservez ce manuel afin de pouvoir le consulter plus tard.
8844078 Clé à chocs de 3/4 po V1,0
2 En cas de questions techniques, appelez le 1-800-665-8685
SPÉCIFICATIONS
Entrée dair 1/4 po
Format de prise carrée 3/4 po
Pression de travail 90 lb/po carré
Débit moyen à un temps de
fonctionnement de 15 secondes
8,25 pi cubes/min
Débit à pleine charge 7,5 pi cubes/min
Couple max. 500 pi-lb
Vitesse nominale 4 500 tr/min
Diamètre min. de tuyau 3/8 po
Matériau
Boîtier en aluminium coulé sous
pression
DÉFINITIONS DE DANGER
Veuillez-vous familiariser avec les avis de danger qui sont présentés dans ce
manuel. Un avis est une alerte indiquant qu'il existe un risque de dommage à la
propriété, de blessure ou de décès si on ne respecte pas certaines instructions.
DANGER ! Cet avis indique un risque immédiat et particulier qui
entraînera des blessures corporelles graves ou même la
mort si on omet de prendre les précautions nécessaires.
AVERTISSEMENT ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui
pourrait entraîner des blessures
corporelles graves ou même la mort si on omet de
prendre les précautions nécessaires.
ATTENTION ! Cet avis indique une situation possiblement dangereuse qui
peut entraîner des blessures mineures ou modérées si on
ne procède pas de la façon recommandée.
AVIS ! Cet avis indique un risque particulier ou une pratique non
sécuritaire qui entraînera des dommages au niveau de
l'équipement ou des biens, mais non des blessures
corporelles.
V1,0 Clé à chocs de 3/4 po 8844078
Visitez www.princessauto.com pour plus d'informations 3
INTRODUCTION
La clé à chocs de 3/4 po peut desserrer ou serrer des écrous et des boulons
avec une force de 500 pi-lb. L’alimentation est commandée au moyen dun
régulateur pneumatique intégré à la base de la poignée.
SÉCURITÉ
AVERTISSEMENT ! Veuillez lire et comprendre toutes les instructions avant
d'utiliser cet outil. L'utilisateur doit respecter les précautions de base
lorsqu'il utilise cet outil afin de réduire le risque de blessure ou de
dommage à l'équipement.
Conservez ce manuel qui contient les avertissements de sécurité, les
précautions, les instructions de fonctionnement ou d'inspection et d'entretien.
AIRE DE TRAVAIL
1. Travaillez dans un environnement de travail sécuritaire. Gardez votre
aire de travail propre, bien éclairée et exempte de toute distraction.
Placez les lampes de façon à ne pas travailler dans lombre.
2. Assurez-vous que les personnes qui ne portent pas l'équipement de
sécurité approprié ne se trouvent pas à proximité de l'aire de travail.
3. Rangez les outils correctement dans un lieu sécurisé et sec. Gardez les
outils hors de la portée des enfants.
SÉCURITÉ PERSONNELLE
AVERTISSEMENT ! Portez de l'équipement de protection personnelle
homologué par l'Association canadienne de normalisation (CSA) ou
l'American National Standards Institute (ANSI).
ÉQUIPEMENT DE PROTECTION PERSONNELLE
1. Portez toujours des lunettes antiprojections qui offrent une protection
frontale et latérale pour les yeux. L'équipement de protection des yeux
devrait être conforme à la norme CSA Z94.3-07 ou ANSI Z87.1 fonction
du type de travail effectué.
2. L’outil peut être à haute pression. Portez des lunettes de sécurité et
des gants pour vous protéger au cours de l'opération. Gardez les mains
à l'écart des parties de caoutchouc exposées du tuyau.
3. Portez un écran facial panoramique de type approprié avec les lunettes
de sécurité puisque cette tâche peut créer des copeaux, des matières
abrasives ou des particules.
8844078 Clé à chocs de 3/4 po V1,0
4 En cas de questions techniques, appelez le 1-800-665-8685
4. Portez des vêtements de protection conçus pour l'environnement de
travail et pour l'outil.
5. Portez un masque antipoussières ou un appareil respiratoire
nominal approprié.
6. Cet outil peut causer des dommages à louïe. Portez une protection
d’oreille afin déliminer ou de réduire le bruit. Si cest possible, ajoutez
un dispositif au niveau de léchappement de loutil pneumatique pour
assourdir le bruit.
PRÉCAUTIONS PERSONNELLES
Gardez le contrôle de l'outil, de vos mouvements et de l'environnement de
travail pour éviter les blessures ou le bris de l'outil.
1. N'utilisez pas l'outil si vous êtes fatigué ou sous l'effet de drogues,
d'alcool ou de médicaments.
2. Évitez de porter des vêtements ou des bijoux pouvant se prendre dans les
pièces mobiles d'un outil. Gardez les cheveux longs recouverts ou attachés.
3. N'utilisez pas l'outil si vous devez étirer les bras pour vous en servir.
Une stabilité et un équilibre appropriés sont nécessaires afin d'avoir un
meilleur contrôle en cas de situations inattendues.
4. Tenez cet outil solidement à laide des deux mains. Un outil tenu dune
seule main peut causer une perte de contrôle.
5. Gardez vos doigts à bonne distance de la gâchette/commutateur lors
du transport de loutil ou du branchement dun tuyau à air ou dun
accessoire. Engagez le verrou de gâchette/interrupteur, le cas échéant.
6. Évitez les mises en marche involontaires. Assurez-vous que le
régulateur/commutateur est en position neutre ou OFF (arrêt) lorsque
l’outil nest pas utilisé et avant de le brancher à une source dair.
7. Ne dirigez jamais le jet dair ou les outils vers votre corps, d’autres
individus ou des animaux. Les débris et la poussière projetés à grande
vitesse peuvent causer des blessures.
8. Des blessures graves ou même la mort peuvent survenir en cas
d’inhalation de lair comprimé. Le jet dair peut contenir du monoxyde
de carbone, des vapeurs toxiques ou des particules solides. Ninhalez
jamais lair comprimé provenant directement de la pompe ou dun outil
pneumatique.
V1,0 Clé à chocs de 3/4 po 8844078
Visitez www.princessauto.com pour plus d'informations 5
CONSIGNES DECURITÉ SPÉCIFIQUES
AVERTISSEMENT! Ne permettez PAS au confort ou à votre familiarisation
avec l'outil (obtenus après un emploi répété) de se substituer à une
adhésion stricte aux règles de sécurité de l'outil. Si vous utilisez cet outil de
façon dangereuse ou incorrecte, vous pouvez subir des blessures
corporelles graves.
1. Utilisez le bon outil pour la tâche à effectuer. Cet outil a été conçu pour
une utilisation spécifique. Évitez de modifier ou d'altérer cet outil ou de
l'utiliser à une fin autre que celle pour laquelle il a été conçu.
2. N’utilisez pas loutil si des pièces présentent des dommages ou sont
déplacées. Réparez ou remplacez les pièces.
3. Ne tenez jamais la prise, la douille et la rallonge de la prise ou les accessoires
au moment de frapper. Ce faisant, vous augmenterez les risques de
coupures, de brûlures ou de blessures causées par les vibrations.
4. Tenez l'outil correctement; soyez prêt à contrer tout mouvement
normal ou brusque et assurez-vous que vos deux mains
sont disponibles.
5. N'utilisez pas dans des espaces restreints et faites attention de ne pas
écraser vos mains entre l'outil et la pièce à travailler, en particulier au
moment de la dévisser.
6. Cet outil n'est pas isolé advenant tout contact avec des conduits ou des
sources électriques sous tension.
7. Ne serrez pas trop les écrous. Ils pourraient se briser et endommager loutil
ou louvrage, ou bien causer une blessure grave. Servez-vous dune c
dynamométrique pour serrer lécrou après avoir utilisé la clé à douilles.
8. Cette clé à chocs ne devrait être utilisée quavec des rallonges et des
douilles pour clés à chocs. Lemploi dautres accessoires pourrait
entraîner leur bris et causer des avaries permanentes à lappareil et des
blessures graves à lutilisateur.
PRÉCAUTIONS RELATIVES AUX OUTILS PNEUMATIQUES
1. Utilisez uniquement un air comprimé propre et sec comme source
d’énergie. Lair contaminé ou humide endommagera progressivement
l’outil.
2. Installez une soupape d'arrêt ou un régulateur sur la conduite afin de
permettre une commande immédiate de l'alimentation en air, en cas
d'urgence, même si un tuyau se fend.
8844078 Clé à chocs de 3/4 po V1,0
6 En cas de questions techniques, appelez le 1-800-665-8685
3. Consultez la pression nominale maximale du fabricant en ce qui
concerne les outils pneumatiques et accessoires. La pression de sortie
du compresseur doit être réglée de façon à ne jamais dépasser la
pression nominale maximale de l'outil (consultez Spécifications). Si on
dépasse la pression nominale maximale, il pourrait en résulter un
risque dexplosion capable dentraîner des blessures et des dommages
aux biens.
4. Arrêtez dutiliser loutil sil ne fonctionne pas correctement ou sil
présente des fuites dair. Attachez une étiquette sur loutil indiquant
quil est « défectueux » ou quil est « hors service », jusquà ce quil soit
réparé.
5. Avant de relier lalimentation en air, fixez correctement tous les
accessoires sur loutil. Un accessoire mal attaché pourrait se détacher
et se briser durant lutilisation.
6. N'utilisez jamais d'oxygène, de gaz combustible ou tout autre gaz
embouteillé en tant que source d'énergie. Une source d'énergie autre
qu'un compresseur d'air pourrait causer une explosion entraînant ainsi
des blessures corporelles graves.
7. Fermez la soupape et évacuez toute la pression dair restante après
chaque utilisation ou avant dajuster loutil.
8. Ne laissez pas l’outil d'air sans surveillance alors que la source d'air
comprimé est en fonction. Fermez la source d'air comprimé et purgez
l’outil d'air de tout air comprimé restant avant de laisser celui-ci sans
surveillance.
9. Des blessures graves peuvent se produire si des débris sont propulsés
à haute vitesse dans le jet dair du compresseur. Portez toujours des
lunettes de sécurité approuvés OSHA afin de vous protéger les yeux
lorsque vous utilisez le compresseur dair.
10. Arrêtez toujours le compresseur dair et évacuez complètement la
pression du réservoir avant de tenter de procéder à lentretien ou de
fixer des outils pneumatiques. Évacuez doucement la pression du
système.
11. Des blessures graves ou même la mort peuvent survenir en cas
d’inhalation de lair comprimé. Le jet dair peut contenir du monoxyde
de carbone, des vapeurs toxiques ou des particules solides. Ninhalez
jamais lair comprimé provenant directement de la pompe ou dun outil
pneumatique.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

Power Fist 8844078 Le manuel du propriétaire

Catégorie
Outils électroportatifs
Taper
Le manuel du propriétaire

dans d''autres langues