U.S. Boiler Company 307B spécification

103796-04 - 3/13

9700609

Price - $5.00

For service or repairs to boiler, call your heating contractor. When seeking information on boiler, provide

Boiler Model Number and Serial Number as shown on Rating Label.

Boiler Model Number

30__B Boiler Serial Number Installation Date

Heating Contractor Phone Number

Address

INSTALLATION, OPERATING AND

SERVICE INSTRUCTIONS FOR

SERIES 3™

Gas - Fired Boiler

2

FOLLOW ALL INSTRUCTIONS and warnings

printed in this manual and posted on the boiler.

INSPECT THE BOILER ANNUALLY. To keep your

boiler safe and efcient, have a service technician

follow the Service checklist near the end of this

manual.

IF YOU ARE NOT QUALIFIED to install or service

boilers, do not install or service this one.

THE BOILER MAY LEAK WATER at the end of

its useful life. Be sure to protect walls, carpets,

and valuables from water that could leak from the

boiler.

PROTECT YOUR HOME IN FREEZING

WEATHER. A power outage, safety lockout, or

component failure will prevent your boiler from

lighting. In winter, your pipes may freeze and cause

extensive property damage. If you must leave

your home unattended for an extended time when

outdoor temperatures are below 32°F, rst turn off

your home’s main water supply and drain the water

from all pipes.

DO NOT BLOCK AIR FLOW into or around the

boiler. Insufcient air may cause the boiler to

produce carbon monoxide or start a re.

KEEP FLAMMABLE LIQUIDS AWAY from the

boiler, including paint, solvents, and gasoline.

The boiler may ignite the vapors from the liquids

causing explosion or re.

KEEP CHILDREN AND PETS away from hot

surfaces of the boiler, boiler piping, and vent pipe.

CARBON MONOXIDE (CO) is an odorless, deadly

gas that may be introduced into your home by

any malfunctioning fuel-burning product or vent

system failure. Consider installing CO alarms near

bedrooms in all levels of the building to warn you

and your family of potential CO exposure.

WARNINGS FOR THE HOMEOWNER

READ THIS ENTIRE MANUAL before attempting

installation, start-up, or service. Improper

installation, adjustment, alteration, service, or

maintenance may cause serious property damage,

personal injury, or death.

DO NOT DISCONNECT PIPE FITTINGS on the

boiler or in the heating system without rst verifying

that the system is cool and free of pressure and

that your clothing will protect you from a release

of hot water or steam. Do not rely solely on the

boiler’s temperature and pressure gage when

making this judgment.

USE PROPER PERSONAL PROTECTION

EQUIPMENT when servicing or working near the

boiler. Materials of construction, ue products, and

fuel contain alumina, silica, heavy metals, carbon

monoxide, nitrogen oxides, and/or other toxic or

harmful substances that can are hazardous to

health and life and that are known to the State of

California to cause cancer, birth defects, and other

reproductive harm.

INSTALL ALL GUARDS, cover plates, and

enclosures before operating the boiler.

THIS INSTALLATION IS NOT COMPLETE until

the front air dam is installed (See Figure 2-a).

Product performance will be negatively affected if

the front air dam is not installed which can cause

serious property damage, personal injury or death.

SIZE THE BOILER PROPERLY relative to the

design heat load or, if using domestic hot water

priority, the peak hot water load, whichever

is larger. A grossly oversized boiler will cycle

excessively and this will lead to premature failure

of the boiler and its components. Our warranty

does not apply to damage from excessive cycling.

ADHERE TO ALL LOCAL CODE

REQUIREMENTS. Contact your local code

inspector prior to installation. In the absence of

a local code, adhere to the National Fuel Gas

Code ANSI Z223.1/NFPA 54 or CAN/CSA B149.1,

Natural Gas and Propane Installation Code.

ALL WIRING must comply with the National

Electrical Code ANSI/NFPA 70 (in the USA) or the

Canadian Electrical Code CSA C22.1 (in Canada)

and any local regulations.

IT IS THE RESPONSIBILITY OF THE INSTALLING

CONTRACTOR to see that all controls are correctly

installed and are operating properly when installation

is complete including verifying that the limit sensor

is fully installed.

Failure to properly install Limit Sensor may result in

property damage, personal injury or loss of life due to

elevated operating temperatures and/or pressures.

WARNINGS FOR THE INSTALLER

3

Congratulations on your purchase of a new Series 3™ boiler—designed and constructed to provide you

with years of reliable service.

• ENERGY STAR™ efﬁciency – friendly on the environment and your wallet.

• Cast iron heat exchanger – for reliability and durability, nothing beats a cast iron heat exchanger.

• IQ Control™ – the most advanced and easiest to use control available.

 • System-friendly – built-in protection from condensation and thermal shock.

1. q Series 3™ Boiler

2. q Vent Damper w/ Carton

 4” Damper  303B (102284-01)

 5” Damper  304B (102284-02)

 6” Damper  305B & 306B (102284-03)

 7” Damper  307B & 308B (102284-04)

 8” Damper  309B (102284-05)

3. q Circulator & Gasket Kit

 Taco 007-2 (8056170)

 Grundfos UP-15 (102805-02)

 B & G NRF-22 (8056174)

4. q Miscellaneous Parts Bag (102627-01)

q Temperature/Pressure Gage; ¼” NPT

(100282-01)

q Circulator Mounting Hardware Kit,

1-1/4” NPT (6056007)

q Drain Valve; ¾” NPT (102802-01)

q Pressure Relief Valve; 30 psi

(81660363)

q Water Manifold for Pressure Relief/

Temp. Gage (80607001)

What's in the crate? 5. q Instruction Envelope (103795-01)

q Instruction & Operation Manual

(103796-04)

q Boiler Warranty Sheet (103203-01)

q Boiler Warranty Card (103204-02)

*IQ Control System Overview

Series 3 Boiler uses a microprocessor based control system called the "IQ Control System". This "IQ

Control System" consists of an Intelligent Hydronic Control (Control) and an IQ Option Panel (Option

Panel) with optional "plug-in" IQ Option Cards (Option Card). The IQ Control System fully integrates both

factory and eld installed components, simplifying installation and troubleshooting. The IQ Control System

is designed to efciently operate the entire boiler system to save energy, installation and setup time while

ensuring adequate supply of heat and domestic hot water.

4

Series 3

Boiler Model Input (MBH) DOE Heating Capacity (MBH) Net AHRI Rating (MBH) AFUE (%)

303B 70 59 51 84

304B 105 88 77 84

305B 140 117 102 84

306B 175 146 127 84

307B 210 176 153 84

308B 245 205 178 84

309B 280 234 203 84

Ratings

SPECIFICATIONS

Boiler

Model Depth Width Height Supply NPT

(inch) Return NPT

(inch) Vent

(inch) Gas NPT

(inch) Relief Valve

NPT (inch) Drain

NPT (inch)

303B 33 12¾ 41 1¼ 1¼ 4 ½ ¾ ¾

304B 33 15½ 41 1¼ 1¼ 5 ½ ¾ ¾

305B 33 18½ 41 1¼ 1¼ 6 ½ ¾ ¾

306B 33 21½ 41 1¼ 1¼ 6 ½ ¾ ¾

307B 33 24¾ 41 1¼ 1¼ 7 ¾ ¾ ¾

308B 33 27¾ 41 1¼ 1¼ 7 ¾ ¾ ¾

309B 33 30¾ 41 1¼ 1¼ 8 ¾ ¾ ¾

Dimensions and Connections

Electrical Requirements: 120VAC, 60 Hz, 1-ph, 15A

Maximum Allowable Working Pressure - 50 psi. Boiler shipped from factory with a 30 psi relief valved.

Boiler Model Allowable Supply

Water Temperature

(°F)

Minimum Return

Water Temperature

(°F)

Minimum Flow

(GPM)

Waterside Pressure Drop

at 20°F DT

(Ft. of Head)

303B 130-220 110 None <1

304B 130-220 110 None <1

305B 130-220 110 None <1

306B 130-220 110 None <1

307B 130-220 110 None <1

308B 130-220 110 None <1

309B 130-220 110 None <1

Water Temperatures and Flows

Boiler

Model Shipping Weight

(lbs) Empty Weight

(lbs) Water Content

(gal)

303B 254 180 2

304B 304 231 3

305B 357 284 4

306B 405 332 5

307B 462 382 5

308B 518 438 6

309B 564 484 7

Weights and Volume

5

Figure S-1: Minimum Clearances to Combustibles and Alcove Dimensions

SPECIFICATIONS (continued)

6

Installation:

1. Unpack the crate ............................................................................................. 7

2. Position the boiler ............................................................................................ 8

3. Provide combustion air .................................................................................... 9

4. Connect venting ............................................................................................... 9

5. Connect gas piping ........................................................................................ 10

6. Connect boiler water piping ........................................................................... 10

7. Connect electrical wiring ................................................................................ 12

8. Program the controls ..................................................................................... 13

9. Check for gas and water leaks ...................................................................... 16

10. Perform startup checks and adjustments ...................................................... 17

Annual Maintenance Checklist ............................................................................ 18

Troubleshooting .................................................................................................... 19

Repair Parts List ................................................................................................... 25

Internal Wiring ....................................................................................................... 31

Appendices:

A – Combustion Air..................................................................................................35

B – Venting ..............................................................................................................36

C – Gas Piping ........................................................................................................40

D – System Piping ...................................................................................................41

E – Filling the System and Checking for Leaks .......................................................45

F – Adjusting Gas Input Rate ..................................................................................46

G – Checking Draft and Combustion .......................................................................47

H – Operation ..........................................................................................................48

I – IQ Control System ..............................................................................................49

BOILER QUICK-START

7

THE BOILER IS TOP-HEAVY. Do not

allow it to tip over.

1. Remove the sleeve.

2. Remove the contents from the skid, except

the boiler.

3. Remove the four (4) hex-drive lag screws

holding the boiler to the skid (Figure 1-a).

DO NOT DAMAGE front air dam. It is

required for proper operation of the boiler.

1. UNPACK THE CRATE

4. Tip the boiler and shimmy it off the skid

(Figure 1-b).

1-a 1-b

8

2. POSITION THE BOILER

WARNINGS

1. Slide the boiler into desired location.

2. Meet the minimum clearances to

combustible construction per the

Speciﬁcation Section of this manual.

3. Allow 24" service clearance in front and on

the left side of the boiler.

OBSERVE MINIMUM CLEARANCES to

combustible walls and ceilings to avoid potential

re hazard.

DO NOT INSTALL ON CARPET. This may cause

a re.

INSTALLING THE BOILER NEAR A SOURCE OF

FLAMMABLE LIQUIDS or gases may cause re or

explosion.

CLEAN BURNERS DAILY if operating the boiler in

a dusty environment.

PROTECT IGNITION SYSTEM COMPONENTS

from sources of water that may spray, drip, or rain

on them during installation or service.

4. Level the boiler, using shims as necessary.

5. Assure that the front air dam (applicable to

5-section thru 9-section boilers only) is in

place and undamaged. See Figure 2-a.

2-a

CAUTION

ASSURE THAT THE FRONT AIR DAM is in place and undamaged. A damaged front air dam will

negatively affect the performance of this boiler, which can cause serious property damage, personal injury

or death.

Note: Front Air Dam applicable

to Models 305B thru

309B only

9

3. PROVIDE COMBUSTION AIR

INSUFFICIENT COMBUSTION AIR

SUPPLY may result in the production and

release of deadly carbon monoxide (CO) into the

home which can cause severe personal injury or

death.

4. CONNECT VENTING

DAMPER MUST BE OPEN when the main burner is ring.

Like all fuel-burning appliances, boilers need air to

operate reliably and safely.

Provide combustion air using the instructions in

Appendix A—Combustion Air.

4-a

IMPROPER VENTING may result in property

damage and the release of ue gases which

contain deadly carbon monoxide (CO) into the home,

which can cause severe personal injury, death or

substantial property damage.

INSPECT EXISTING CHIMNEY before

installing boiler. Failure to clean or replace

perforated pipe or tile lining will cause severe injury

or death.

The vent system shall be designed and constructed

in accordance with NFPA 54 and applicable local

codes to develop a positive ow adequate to convey

ue or vent gases to the outdoors, while ensuring

that ue gases do not cool prematurely.

Observe all general venting guidelines provided in

Appendix B—Venting. Additionally:

1. This appliance shall be vented into a listed

gas vent, masonry, metal, or factory-built

chimney as required by NFPA 54 and

applicable local codes for Category I

appliances. If venting this appliance into

a masonry chimney, the chimney must be

lined with approved clay ue lining, a listed

chimney lining system, or other approved

material as required by NFPA 54 and

applicable local codes.

2. Attach the vent damper with three sheetmetal

screws around the perimeter of the ue collar

(Figure 4-a), oriented so that the position

indicator is visible. The vent damper may

also be mounted anywhere between the ue

outlet and the chimney within reach of the

electrical harness.

3. Vent connector shall meet the requirements

of NFPA 54 and applicable local codes.

Using sheetmetal screws, attach the vent

connector between the vent damper and the

vertical chimney (Figure 4-b).

4-b

10

2. Screw the water supply manifold into the

boiler outlet tapping “O.”

3. Orient the manifold with the relief valve on

top.

4. Screw the relief valve into manifold tapping

“RV”.

i This installation is not complete until the

relief valve is installed.

PIPE THE RELIEF VALVE DISCHARGE

to a location where it will not harm

people or damage property. The relief valve may

discharge scalding hot water or steam.

BLOCKING THE RELIEF VALVE may

result in boiler explosion.

5. Screw the temperature-pressure gage into

manifold tapping “G”.

6. Connect the system supply to the open end

of the manifold "S" using a 1¼” male NPT

tting.

5. CONNECT GAS PIPING

Size gas piping according to Appendix C – Gas

Piping SHUT OFF GAS SUPPLY before

servicing the boiler.

ALL GAS PIPING MUST BE GAS

TIGHT. Use gas rated thread compound

on all threaded joints to avoid leaks, which may

result in re or explosion.

SIZE GAS PIPING, regulators, valves,

and meters so as to provide an adequate

gas ow and pressure to the boiler during

operation. Failure to do so may cause poor

combustion, noise, injury, or death.

1. Remove boiler door, locate gas valve and

remove plastic shipping plug.

2. Thread a ¾" x 1½" nipple, a 90° street

elbow, or a Honeywell ange onto the gas

valve and pipe through the slot in the left

jacket panel (Figure 5-a). In Canada, close

nipples and street ells are not approved for

use as gas piping.

3. Pipe through the left jacket panel, and

complete drip leg as shown (Figure 5-a).

6. CONNECT BOILER WATER PIPING

General system piping guidelines are included in

Appendix D—System Piping.

Additionally, for this particular boiler install piping

shown below (Figure 6-a).

6-a

1. Apply sealant to all threads.

RV

S

R

O

G

D

5-a

11

7. Screw an installer-supplied 1¼” pipe or

nipple into the water return tapping “R”.

8. Screw the supplied drain valve into tapping

“D”.

6. CONNECT BOILER WATER PIPING (continued)

9. See Figure 6b for suggested near boiler

piping of IQ Options.

6-b

Item Description Part Number

1 1¼ x 1¼ x ½ Tee 806601021

2 Immersion Well, ½ NPT 80160456

3 1¼ x 6 Nipple 806600029

41¼ Tee 806601030

5 1¼ x ¾ Bushing 806600504

6 LWCO Sensor, ¾ NPT 102305-01

7 1¼ x 3 Nipple 806600005

8 1¼ Elbow 806601528

12

DISCONNECT ELECTRICAL POWER

to the boiler and heating system before

servicing. Positively assure that no voltage is

present. Lock electrical boxes to prevent someone

from inadvertently restoring power before the

heating system is safe to operate.

NEVER DEFEAT OR JUMP OUT safety

devices.

PROTECT EACH BOILER circuit with a

properly sized over-current protection

device.

MAKE ELECTRICAL CONNECTIONS

CAREFULLY according to the boiler’s

wiring diagram and instructions

Refer to the Internal Wiring diagrams later in this

manual.

1. Locate the wiring box on the left side of the

boiler and open the cover (Figure 7-a).

2. Install a 120V disconnect near the boiler.

3. Connect the 120V wiring from the disconnect

to the boiler's white (neutral), black (hot),

and green (ground) labeled "120VAC Power

supply". Do not reverse polarity.

4. Connect the 120V wiring from the circulator

to the white (neutral) yellow (hot) wires

marked "circulator".

WIRE AN ADDITIONAL SAFETY LIMIT

such as a low water cutoff or temperature

limit device, other than an IQ™ Control device,

in series with the 120V circuit used to power the

boiler. Do not alter the boiler’s factory wiring when

adding an additional limit.

7. CONNECT ELECTRICAL WIRING

5. Connect the 24V wiring from the thermostat

to the "T-T" terminals on the Option Control

Panel.

6. To connect other external devices, refer to

the instructions included with these devices.

7-a

1



123 T T

7-b

THE MAXIMUM ALLOWABLE

CURRENT for each circulator is 5 amps at

120V AC. For circulators with higher amp ratings,

you must install a circulator relay or starter coil to

provide line voltage to the circulator and connect

only the relay or starter coil to boiler terminals.

The combined boiler and circulator amperage must

not exceed 15 amps.

Install over-current protection in accordance with

authority having jurisdiction or, in the absence of

such requirements, follow the National Electric

Code, NFPA 70, and/or CSA C22.1 Electrical

Code. Do not provide over-current protection

greater than 15 amperes.

13

8. PROGRAM THE CONTROLS

Intelligent Hydronic Control

8-b

IQ Option Panel

8-a

Using Intelligent Hydronic Control Display

The Intelligent Hydronic Control (control) is located

inside the boiler front door, just above the IQ

Option Panel (Figure 8-a).

Intelligent

Hydronic Control

The control display, along with Up ñ, Down ò,

and “I” keys may be used to view boiler operating

status (Figure 8-b). Please note that these keys

look similar to the keys on the IQ Option Panel

but are in a different orientation, and they perform

different functions.

Viewing the Operating Mode Options

In operating mode the user may view (but not

change) boiler operating status, settings and

troubleshooting information. To view control

display information:

Unit Display

OR

Sample

Display

1 sec

1. Press and release the “I” key on the

control to change from one parameter to

the next. Each setting will alternately ash

between the relevant display code and its

corresponding value.

Operating Mode Options

StA Status

bt Boiler Temperature

SP Operating Setpoint (Outdoor Reset)

HL High Limit Setting

HdF High Limit Differential

tt Heat Request Status

dh DHW Heat Request Status

FLA Flame Current

rUn Run Time Hours

CYC Boiler Cycles

Err Error (see Error Numbers)

The STA (status) display code has the below listed

values. This list is also available on the control

cover.

Status Code Displayed in STA Mode

1 Standby

4 Prepurge

6 Spark

7 Flame Proving

8 Running

10 Retry/Recycle Delay

13 Soft Lockout

14 Hard Lockout

15 Waiting for Limit to Close

16 Flame Present Out of Sequence

17 Self Test

18 Waiting for Damper to Open

20 Damper Failure to Open

For example, when the “I” key is pressed on the

control until “bt” is displayed, it will then ash a

three digit number (such as “180”) followed by

either “F” (or “C”). This indicates that the boiler

water temperature is 180°F. Other operating

parameters display the information in a similar

fashion.

14

8. PROGRAM THE CONTROLS (continued)

Please note that in operating mode to hold the

display on the value the user can press and hold

either the Up ñ or Down ò keys and the value

will be continuously shown. This may be helpful in

watching a value “live”.

Changing the Adjustable Parameters

To adjust the Parameters such as High Limit

Setpoint and High Limit Differential:

1. Access the adjustment mode by pressing

and holding the Up ñ, Down ò, and “I”

keys simultaneously for three (3) seconds.

This procedure is intended to discourage

unauthorized changes or accidental changes

to limit settings.

2. Press the "I" key to display available

Adjustment Mode options. Select an option.

Adjustment Mode Options

HL_ 140-220°F Adjust High Limit Setting

dF_ 10-30°F Adjust High Limit Differential

Or_ 0-10 minutes Circulator Overrun Time

PP_ 2-20 minutes Circulator Pre-purge Time

St_ 140-180°F Start Temperature

Pt_ On or off Priority time

dh_ dh or tt2 DH Terminal Function

rst Reset Lockout

f-C F or C Select degrees F or C Mode

bac Back to Operating Mode

3. Press the Up ñ and Down ò keys to adjust

the displayed item to the desired value.

4. To return to the normal operating mode from

the Adjustment Mode, when the "bAc” option

is displayed, press either the Up ñ or Down

ò key. If no keys are pressed, after ve (5)

minutes the control will automatically return

to the Operating Mode.

More Information about Adjustable Parameters

1. High Limit (HL_)

The control is factory programmed with a

High Limit Setpoint of 180°F. The burner

turns "off" when the boiler temperature (bt)

is above Operating Setpoint. The Operating

Setpoint (SP) will equal the High Limit

Setpoint unless an IQ Outdoor Reset IQ

Option Card is installed.

The Outdoor Reset IQ Option Card reduces

the Operating Setpoint to regulate heat

delivery, increase home comfort and

save energy. Refer to the Appendix I for

additional information. The High Limit

Setpoint is adjustable between 140° and

220°F.

2. Differential (df_)

The control is factory programmed with a

Differential of 15°F. The Differential is the

number of degrees the boiler temperature

must decrease below the Operating Setpoint

before the boiler can restart. The differential

is adjustable between 10° through 30°F.

3. Circulator Overrun Time (OR_)

The control is factory programmed with

a Circulator Overrun Time of 0 minutes.

Circulator Overrun Time (also called

“circulator off delay” or “circulator post

purge”) continues circulator operation after

a call for heat has ended, sending excess

heat from the boiler into the system. Ensure

system piping and zone panel settings allow

water ow to the priority zone after the call

for heat ends. The Circulator Overrun Time

is adjustable between 0 through 10 minutes.

4. Circulator Pre-purge Time (PP_)

When the boiler is warm (boiler water

temperature higher than 140°F (adjustable

using Start Temperature parameter)) and

there is a thermostat call for heat, the

system circulator is started and boiler ring

is delayed Circulator Pre-purge minutes. If

the temperature drops below 140°F or there

is a DHW call for heat the boiler is started

without delay. Additionally, the boiler is

started without delay if the thermostat call

for heat is initiated when the boiler water

temperature is less than 140°F. This

feature helps save energy by satisfying

home heating needs with residual boiler

heat rather than cycling the boiler. The

Circulator Pre-purge time has a factory

setting of 2 minutes and is eld adjustable

between 2 and 20 minutes. When reset card

is installed, pre-purge time may be adjusted

down to zero (0) minutes. Refer to Table 8a.

15

8. PROGRAM THE CONTROLS (continued)

Table 8a: Circulator Pre-purge Time example,

(PP_ = 2 minutes)

Call for

Heat

Source

DHW

Terminal

Selection

Boiler

Temperature Burner Status

TT = on - <140 Start with no delay

TT = on - >140 Start after 2 minute delay

DHW = on tt2 <140 Start with no delay

DHW = on tt2 >140 Start after 2 minute delay

DHW = on dh <140 Start with no delay

DHW = on dh >140 Start with no delay

5. Start Temperature (St_)

Amount of “Heat available” is calculated

by taking the difference between measured

boiler water temperature and the Start

Temperature setting. Useful “Heat

Available” is dependent on the type of

heating emitter installed in the home.

Heat emitters require a certain minimum

temperature to operate effectively. Our

default settings reect cast iron radiators.

Fan Coils may require a start temperature

setting of 180°F or 160°F before providing

heat to the home. The Start Temperature

has a factory setting of 140°F and is eld

adjustable between 140°F and 180°F.

6. Priority Time (Pt_)

When the Priority Time parameter is set

to “on” and Domestic Hot Water (DHW)

call for heat is “on” the DHW demand will

take “Priority” over home heating demand.

During Priority Time the system circulator

will be forced “off”. Priority Time ends and

the system circulator is released to service

home heating demand when Domestic Hot

Water call for heat is over. When Priority

Time parameter is set to “Off” the DHW

call for heat does not force “off” the system

circulator. The Priority Time has a factory

setting of “On” and is eld adjustable

between “On” and “Off” Refer to Table 8b.

7. Domestic Hot Water (DHW) Terminal

Function (dh_)

The control allows conguration of the

DHW Circulator output functionality to help

the Boiler integrate into each installation

more effectively. The DHW Circulator

output can be connected to a domestic hot

water circulator or a second heating zone

circulator. These applications are selected

as follows:

a. When dh_ is set equal to Domestic Hot

Water Demand (h)

When there is an Indirect Water Heater

(IWH) the control provides “DHW” input

terminals for the IWH Aquastat and “DHW

Circulator” output terminals for the DHW

Circulator. When there is a DHW call for

heat, the System Circulator is “forced off”,

the DHW Circulator terminal is energized

and the circulator pre-purge time delay

control logic is bypassed to allow the

boiler to re without delay. When DHW

demand ends the System Circulator

“force off” is removed, the circulator

can respond normally, and the DHW

Circulator is de-energized. The DHW

call for heat is detected by a voltage on

to the "DHW" terminal. When the Priority

Time parameter is set to “off” the System

Circulator is not forced off for a DHW call

for heat. Refer to Table 8b.

Table 8b: DHW Terminal Function (dh_)

Selection = Domestic Hot Water Demand,

(Parameter dh_ = dh)

Call for Heat Circulator Status

T-T

Input DHW

Input

Priority

Time

(Pt_)

System

Circulator

Output

DHW

Circulator

Output

on off On on off

on on On off on

off on On off on

on off OFF on off

on on OFF on on

off on OFF off on

16

b. When dh_ is set equal to Second Heating

Zone (tt2)

When there is no IWH the “DHW

Circulator” output may be congured to

control a second heating zone. This is

particularly helpful when the home uses

only two heating zones. The control

replaces the need for a two circulator

zone panel. When DHW Terminal

Function (dh_) is set to “tt2" the control’s

two circulator outputs are used to control

two independent heating zones. Refer

to Table 8c. A “TT” input causes a call

for heat and energizes the “System

Circulator” output to service heating zone

1 and a second zone's thermostat wired

to the “DHW” input causes a call for heat

and energizes heating zone 2 circulator

wired to the "DHW Circulator" output.

When there is a Second Heating Zone

(call for heat) the boiler is started and the

DHW Circulator terminal is energized.

When Second Heating Zone is de-

energized the call for heat is ended and

the Second Heating Zone Circulator is

de-energized. A Second Heating Zone

is detected by sensing a voltage on the

DHW terminal.

8. PROGRAM THE CONTROLS (continued)

Using the IQ Option Panel

IQ Option Cards are available from U.S. Boiler

Company distributors and are the simplest way

to add functionality, safety and efciency to your

heating system. The IQ Option Panel provides

an easy and convenient means to "plug-in" an

Auxiliary High Limit, Low Water Cut-off and/or

Outdoor Reset function.

For installation, programming, and troubleshooting

instructions, refer to the instructions supplied with

those cards.

Using the Optional LCD Display Kit

The LCD Display is an easy to use touch screen

type display that allows a technician to monitor and

adjust the control and connected IQ Option Cards.

All boiler settings, status and error codes are

displayed in full text. All Outdoor Reset IQ Option

Card parameters are adjustable with graphic and

help information screens. The LCD Display Kit

includes a mounting bracket and wiring harness

to allow mounting in the boiler plastic hood above

the front door. For installation, programming,

and troubleshooting instructions, refer to the

instructions supplied with the display.

Call for Heat Circulator Status

T-T

Input DHW

Input

System

Circulator

Output

(Zone 1)

DHW

Circulator

Output

(Zone 2)

off off off off

on off on off

on on on on

off on off on

Table 8c: DHW Terminal Function (dh_)

Selection = Second Heating Zone,

(Parameter dh_ = tt2)

9. CHECK FOR GAS AND WATER LEAKS

GAS LEAKS may result in re or

explosion.

WATER LEAKS may cause extensive

property damage.

Refer to Appendix E – Filling the System and

Checking for Leaks

17

10-b

10. PERFORM STARTUP CHECKS AND ADJUSTMENTS

FAILURE TO PERFORM THESE

CHECKS of the boiler's combustion and

safety systems may result in serious property

damage, injury, or death.

IF YOU SMELL GAS, STOP and repair

the leak. Lighting the boiler when gas is

leaking may cause explosion or re.

Follow the checklist below:

1. Verify that the venting, water piping, gas

piping, and electrical systems are properly

installed and checked.

2. Apply power to the boiler.

3. Adjust zone thermostat to maximum setting.

4. Allow gas line to purge of air.

q Boiler lights cleanly within 60 seconds.

5. Adjust gas input rate. See Appendix F

– Adjusting Gas Input Rate

10-a

q Pilot and main burner ﬂames appear

clean and blue.

6. Disconnect pilot lead wires from gas valve

(Figure 10-b).

q Boiler shuts off.

7. Reconnect pilot lead wires to gas valve.

q Boiler restarts.

8. Adjust zone thermostat to minimum setting.

q Boiler shuts off.

9. Adjust zone thermostat to maximum setting.

10. Observe temperature gage as boiler heats.

11. Adjust the high limit setting to its minimum

level (see "Programming High Limit" in

Section 8).

q Boiler shuts off when temperature gage

reads within 15°F of high limit setting.

12. Return high limit to the desired setting (see

"Programming High Limit" in Section 8).

13. Check draft. See Appendix G

– Checking Draft and Combustion.

q No spillage observed.

14. Check combustion in the vent stack and

record results in the spaces provided below.

_____ CO2 (less than 7%)

_____ O2 (more than 9%)

_____ CO (less than 50 ppm, air free)

ANY FAILED STARTUP CHECK

Must be corrected before placing the boiler

in service.

18

ANNUAL MAINTENANCE CHECKLIST

WARNINGS

THE BOILER CONTAINS REFRACTORY

CERAMIC FIBER, a possible human carcinogen

Use a NIOSH approved respirator when servicing

high-temperature insulation and gasket materials.

Wash exposed skin gently with soap and water

after contact Wash exposed clothing separate

from normal laundry.

LABEL ALL WIRES prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation

FAILURE TO MAINTAIN THE BOILER in proper

working condition may lead to re, explosion,

personal injury or death, and extensive property

damage.

TURN OFF ALL GAS AND ELECTRIC power

supplies to the boiler before servicing. Contact with

or release of dangerous ammable gas, electrical

voltage, moving parts, and very hot water under

pressure may cause serious personal injury,

property damage, or death.

LOCK ELECTRICAL BOXES AND GAS VALVES

CLOSED to prevent someone from inadvertently

restoring power or gas before the heating system is

safe to operate.

Equipment you will need:

q Soft bristle brush

q Bristle ue brush

q Vacuum with brush attachment

Perform these tasks each year:

1. Clean low water cutoff probe (if applicable).

2. Inspect vent for obstruction and signs of

condensation, distortion, overheating or gas

leakage.

3. Clean vent terminal and air intake screens.

4. Inspect boiler ue passages:

(1) Remove vent pipe, damper.

(2) Remove top panel and hood.

(3) Remove blocked vent switch and

canopy.

(4) Examine all ue passageways. Using

bristle ue brush and vacuum,

remove any soot or obstructions.

5. Remove and clean main burners:

(1) Remove jacket front panel.

(2) Disconnect pilot tubing at gas valve.

(3) Disconnect pilot lead wires at gas valve.

(4) Remove wires from ame roll-out switch.

(5) Remove burner access panel.

(6) Mark location of the pilot main burner on

the manifold if the marking on manifold

is missing or obliterated. AM-1

(7) Hold burner at throat. Lift front of burner

to clear orice (Figure AM-1). The

burner that holds the pilot can only be

removed by rst lifting the burner

adjacent to its right.

6. Perform Startup Checks and Adjustments

described earlier in this manual.

7. Check operation of airow sensing switches.

8. Check for water leaks on the boiler or water

pooling around boiler.

9. Manually operate the relief valve. If the

water is grey or black, there is excessive

oxygen in the system. Oxygen is corrosive

to boilers. Eliminate any source of oxygen.

10. Verify proper operation after servicing.

19

Before troubleshooting

The following pages contain trouble shooting

tables for use in diagnosing control problems.

When using these tables the following should

be kept in mind:

1. This information is only meant to be used by

a professional heating technician as an aid

in diagnosing boiler problems.

2. Where applicable, follow all precautions

outlined in Section 10, 'Perform Startup

Checks and Adjustments' on page 17.

3. In general, these tables assume that

there are no loose or miswired electrical

connections. Before using these tables

inspect all electrical connections on the

boiler to make sure that they are tight. Also,

check the wiring on the boiler against the

wiring diagram in Figures IW-1 and IW-2.

Ensure that incoming 120 Vac power polarity

is correct and that the boiler is properly

grounded. Further, ensure that the control

power supply is 24 VAC (minimum 18 VAC

to maximum 30 VAC) and polarity is correct.

4. All controls on the boiler are tested at least

once in the manufacturing process and a

defective control or component is generally

the least likely cause. Before replacing a

component, try to rule out all other possible

causes.

5. When checking voltage across wiring

harness pins be careful not to insert

the meter probes into the pins. Doing

so may damage the pin, resulting in a

loose connection when the harness is

reconnected.

TROUBLESHOOTING

Press “I” key on the control to change

from one parameter to the next. Each

setting will alternate between display

code (for example STA) and value.

When Err (error) is shown:

Value Description

4 Flame current lower than threshold

6 Flame Out of Normal Sequence

18 Electronics Failure

23 Flame Sensed During Pre-purge

32 Temperature Sensor Failure

55 Damper Failed to Open

57 Flame Rod Shorted to Ground

58 AC Line Frequency

59 Line Voltage Error

60 Thermostat input higher than threshold

61 Line Voltage Unstable

63 Soft Lockout – Recycles Exceeded

64 Soft Lockout – Internal Failure

Possible STA (status) values:

Value Description

1 Standby

4 Pre-purge

6 Spark

7 Flame Proving

8 Running

10 Retry/Recycle Delay

13 Soft Lockout

14 Hard Lockout

15 Waiting for Limit to Close

16 Flame Present Out of Sequence

17 Self Test

18 Waiting for Damper to Open

20 Damper Failure to Open

20

TROUBLESHOOTING (continued)

Use Control Display ERR (error) Number To Direct Troubleshooting Efforts

If the control detects an error it will ash “Err” (error) followed by a number. Use this number to identify

the boiler problem and corrective action in the table below. If there is no Err display proceed to next

Section:

Display Status Recommended Corrective Action

Blank Boiler or Control is not powered No 120 Vac Power at boiler, check breaker and wiring between breaker

panel and boiler

Err 4 Flame Current Lower than Threshold Check pilot assembly. Refer to Troubleshooting Section, 6.

Err 6 Flame Sensed Out of Normal Sequence Flame sensed out of normal sequence (before opening gas valve or after

closing gas valve). Check gas valve for proper operation.

Err 18 Electronics Failure Cycle power to control. Replace control if problem persists.

Err 23 Flame Sensed During Pre-purge Flame sensed during post-purge (before gas valve signaled open). Check

the gas valve for proper operation. Replace gas valve if problem persists.

Err 32 Temperature Sensor Failure

Temperature sensor or interface failure (open or short connection, increased

connection resistance, dual sensor mismatch) or control hardware failure.

- Check sensor is securely attached to control P7 connector.

- If secure, replace sensor.

- If problem persists, replace control.

eRR 35 Duplicate Zone Alarm Refer to IQ Zone Panel Instructions.

Err 55 Damper Failed to Open Atmospheric Damper End Switch failed to close (end switch contacts stuck

open). Refer to Troubleshooting Section, 5.

Err 57 Flame Rod Shorted to Burner Ground

Flame Rod shorted to burner ground, this can result from excessive ue gas

condensation.

- Check for excessive condensate. Dry pilot. Adjust setpoint higher.

- Check for loose or damaged ignition wire.

Err 58 AC Line Frequency Error AC Signal is too noisy or frequency is incorrect. Check supply voltage.

Err 59 Line Voltage Error AC voltage out of specication high or low. Check supply voltage.

Err 60 Thermostat Input Higher than Threshold Check thermostat wiring.

Err 61 Line Voltage Unstable Possibly too many heavy loads switching on and off cause erratic supply

voltage. Check supply voltage.

Err 63 Soft Lockout – Maximum Recycles

Exceeded Maximum number of recycles exceeded. Refer to Troubleshooting Section, 6.

Err 64 Soft Lockout – Internal Failure

The electronics has detected an error. This can be caused by an actual

controller internal fault or wiring fault:

- Check vent damper, cycle power with vent damper disconnected. If error

is cleared, reconnect the vent damper and refer to Recommended

Corrective Action listed under stA 20, damper failed to open.

- Check pilot assembly,

- If problem persists, replace the control.

Err 89 Communication Lost Check wiring between control and IQ Zone Panel or IQ Reset Card.

La page charge ...

U.S. Boiler Company 307B spécification

Ce manuel convient également à

U.S. Boiler Company 307B spécification

dans d''autres langues

Autres documents