Sanyo SHBN 2AVOZ Module of Wireless Pistol Tool Manuel utilisateur

SHBN 2AVOZ Module of Wireless Pistol Tool
Sanyo
Marque
Sanyo
Modèle
SHBN 2AVOZ Module of Wireless Pistol Tool
Catégorie
Antennes réseau
Taper
Manuel utilisateur
User Manual
Since this module is not sold to general end users directly, there is no user manual of module.
For the details about this module, please refer to the specification sheet of module.
This module should be installed in the host device according to the interface specification (installation
procedure).
The following information must be indicated on the host device of this module;
[ for FCC ]
Contains Transmitter Module FCC ID: 2AVOZ-SHBN
or
Contains FCC ID: 2AVOZ-SHBN
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe in the user's
manual and also either describe on the device packaging or on a removable label attached to the device.
[ for ISED(IC) ]
Contains IC: 26102-SHBN
The following statements must be described on the user manual of the host device of this module;
[ for FCC ]
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
This device complies with below part 15 of the FCC Rules.
Part 15 Subpart C
Part 15 Subpart E
The modular transmitter is only FCC authorized for the specific rules parts (i.e., FCC transmitter
rules) listed on the grant, and the host product manufacture is responsible for compliance to
any other FCC rules that apply to the host not covered by the modular transmitter grant of
certification.
The final host product still requires Part 15 Subpart B compliance testing with the modular
transmitter installed.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment
should be installed and operated keeping the radiator at least 20cm or more away from person’s
body .
[ for ISED(IC) ]
for indoor use only
Pour usage intérieur seulement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the ISED radio frequency (RF) Exposure rules. This
equipment should be installed and operated keeping the radiator at least 20cm or more away
from person’s body.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les règles d’exposition aux fréquences
radioélectriques (RF) CNR-102 de l’ISDE. Cet équipement doit être installé et utilisé en gardant
une distance de 20 cm ou plus entre le radiateur et le corps humain.
Model No. Antenna Type Antenna Gain
H2B1PC1A1C PCB +1.8dBi (2.4GHz), +3.9dBi (5GHz)
SXANTFDB24A55 PCB(On board) +2.1dBi (2.4GHz), +2.2dBi (5GHz)
Antenna List
This radio transmitter (26102-SHBN) has been approved by Innovation, Science and Economic
Development Canada to operate with the antenna types listed below, with the maximum
permissible gain indicated. Antenna types not included in this list that have a gain
greater than the maximum gain indicated for any type listed are strictly prohibited for use
with this device.
Le présent émetteur radio (26102-SHBN) a été approuvé par Innovation, Sciences et
Développement économique Canada pour fonctionner avec les types d'antenne énumérés
ci-dessous et ayant un gain admissible maximal. Les types d'antenne non inclus dans cette
liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste,
sont strictement interdits pour l'exploitation de l'émetteur.
Antenna type Gain Impedance
PCB
PCB(On board)
+1.8dBi (2.4GHz), +3.9dBi (5GHz)
+2.1dBi (2.4GHz), +2.2dBi (5GHz)
50 ohm
50 ohm
Type d’antenne Gain l'impédance
PCB
PCB(On board)
+1.8dBi (2.4GHz), +3.9dBi (5GHz)
+2.1dBi (2.4GHz), +2.2dBi (5GHz)
50 ohm
50 ohm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Sanyo SHBN 2AVOZ Module of Wireless Pistol Tool Manuel utilisateur

SHBN 2AVOZ Module of Wireless Pistol Tool
Sanyo
Marque
Sanyo
Modèle
SHBN 2AVOZ Module of Wireless Pistol Tool
Catégorie
Antennes réseau
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents