Tasco 119256CW Manuel utilisateur

03-13

Trail Camera

Model #: 119256CW

Instruction Manual

Notice D’utilisation

TABLE OF CONTENTS PAGE

ENGLISH

FrANçAIS

3-22

23-44

3

Page Index

Introduction 5

Parts & Controls Guide 6-7

Battery and SD Card Installation 8

About the Setup Menu 9

Using the Setup Menu 9

SETUP MENU REFERENCE TABLE 10-11

Camera Operation 12

Mount the Camera 12

Power on the Camera 12

Test the Coverage Area 13

Secure the Camera 13

Viewing the Photos and Videos 14

Glossary 15

Technical Specications 16

Troubleshooting/FAQ 17-20

4

IMPORTANT NOTE

Congratulations on your purchase of one of the best trail cameras on the

market! Tasco is very proud of these cameras and we are sure you will

be pleased with yours as well. We appreciate your business and want to

earn your trust. Please refer to the notes below and the instructions in

this manual to ensure that you are completely satised with this product.

If your Tasco Trail Cam does not seem to be functioning properly

or if you are having photo/video quality issues, please check the

Troubleshooting/FAQ section on pages 17-20.

Problems are often due to something simple that was overlooked, or

require only changing one setting to solve.

If your problem continues after trying the solutions in the

Troubleshooting/FAQ section, please call Tasco Customer Service at

(800) 423-3537. In Canada, call (800) 361-5702.

Tasco recommends using 4 Energizer® Lithium AA batteries in this Trail

Cam to obtain maximum battery life.

Do Not Mix Old and New Batteries

Do not mix battery types-use ALL lithium or ALL alkaline.

Rechargeable batteries are not recommended.

Tasco recommends using SanDisk® SD and SDHC Cards

(up to 32GB capacity) in this Trail Cam.

5

INTRODUCTION

Congratulations on your purchase of a Tasco Digital Trail Camera. This

camera is designed to record animal activity in the outdoors with its still

image and movie modes and weatherproof, rugged construction. Your

trail cam features a compact, portable size and an extra long battery life.

Main Features:

• 1.3 MP digital sensor

• Compact Size (120mm*94mm*46mm)

• Long Battery Life (Up to 6 months)

• Trigger Time=1.3 seconds or less

• Automatic IR Filter

• LCD Display

• 15 Night Vision LEDs

• Adjustable Photo Delay: 5~ 59 second ,1~ 10mins (default 10S)

• Multiple Shot Mode (3 images per trigger)

• 640*480 at 30 FPS Videos

• Supports up to 32 GB SD Card

• Date, Time & Moon Phase Imprint

• Auto Exposure

• Auto White Balance

• Power Supply: 4 AA batteries (lithium or alkaline)

• Mounting Socket for Standard Tripods

• Weatherproof

6

Parts and Controls Guide

Front of Camera

Camera

Lens

Infrared

LED Array

PIR Motion

Sensor

Tripod

Socket

Padlock

Hole

IR LED Array Detail

PIR

Indicator

(Setup

Mode

Only

Light

Sensor

7

Control Panel Detail

Parts and Controls Guide

Control Panel

(Front Unlatched & Opened)

Power

Switch

USB Port

LCD

Display

SD Card

Slot

Battery

Compartment

8

BATTERY and SD CARD INSTALLATION

Your Tasco Digital Trail Camera is designed to operate using 4 AA batteries.

We recommend using Lithium (for longest life) or Alkaline batteries.

NOTE: Always set the power switch to the OFF position when installing or

removing batteries.

Please make sure the batteries are inserted correctly, as indicated inside

the battery compartment. Incorrect voltage or polarity (+/-) will damage

the camera.

Do not mix old and new batteries.

Do not mix battery types-use ALL lithium or ALL alkaline.

Rechargeable batteries are not recommended.

Memory

Your Digital Trail Camera has a memory card slot, to accept SD cards up to

32GB max. capacity (sold separately).

Inserting an SD card

• Make sure the power switch is in the OFF position whenever adding

or removing memory.

• Insert an SD card into the card slot completely and oriented correctly

as shown by the icon above the slot (label up, contacts facing down

and notched corner on the right).

• To remove the SD memory card, depress the SD card and pull out

the card gently.

Using a new, blank SD card is recommended. If the SD card has been used

in another device, please make sure to format using the Format option in

the Trail Cam’s Setup menu before you set the camera to capture photos/

videos. New cards are ready to use straight from the package.

9

ABOUT THE SETUP MENU

Slide the power switch to the On position. You’ll see “WAIT” on the display,

then the setup menu screen. Before you start using the camera, you’ll no

doubt want to set the date/time so they are imprinted correctly on your

photos, and maybe change the trigger delay time and image resolution

to your preferences. This is done by editing the settings of an item listed

in the Setup Menu.

To enter the Setup Menu at any time, press the SETUP button (to left of

the power switch).

USING THE SETUP MENU

The Setup Menu has 5 dierent items, which appear on a list in the left

frame of the display. Here’s how to edit (change) the setting of a menu

item:

1. Select the menu item you want to edit by pressing the UP or DOWN

button until the item is blinking. Note: you can see the current/

default setting for each item (without changing it) in the main center

frame as you move up and down the list of items.

2. Press the OK button.

3. You can now select the setting you prefer for the selected item by

pressing the UP or DOWN button (do not hold the button down). The

setting displayed in the center frame will blink until you press OK to

conrm it is the setting you want to save.

4. To exit the Setup menu at any time, simply press the Setup button.

SETUP MENU DISPLAY

SELECTED

MENU

ITEM

CURRENT

SETTING OF

SELECTED ITEM

Indicates Photo (1P or 3P) or Movie Mode

Battery Level

10

Menu Item

Settings

(Bold=default)

Description/Operation

Date set year, month,

and day

Press OK and use the UP/DOWN

keys (to change the setting), then

press OK again to go to the next

date parameter and repeat, to

set the current year, month, and

day. Press OK after setting the

day to move on and set the Time

(next item)

Time set hour and

minute

Press OK and use the UP/DOWN

keys (to change the setting) then

OK again ( to move to the next

eld) to set the current hour (24-

hr format only, “00”=midnight,

“12”=noon) and minute.

Delay set minutes (0-

10) or seconds

(5-59)

Default delay

time= 10 sec.

Selects the length of time that

the camera will “wait” until it

responds to any additional

triggers from the PIR after an

animal is rst detected and

remains within the sensor’s

range. During this user set

“ignore triggers” interval, the

camera will not capture photos/

videos. This prevents the card

from lling up with too many

redundant images. Settings

begin with 10 second default

time. Press OK, set the delay time

in minutes (if desired), press OK

and set the delay in seconds.

The following table lists all of the menu items, their available settings,

and a description of their functions:

11

Menu Item

Settings

(Bold=default)

Description/Operation

Mode 1.3M/3M (with

Mode set to

1P or 3P for

photos),

5-60 Sec (in

Movie (video)

mode

Select “Mode” and press OK. Use

UP/DOWN to select 1P (single

photo), 3P (burst of 3 photos), or

Movie (video mode). Press OK.

Use UP/DOWN to set LO (1.3 MP)

or HI (3 MP) still photo resolution

(High resolution provides better

quality photos, low resolution

allows you to store more photos

on the SD card), or video length

from 5-60 sec. (if video mode was

selected).

Format FO/NO,

Y/N

Deletes (erases) all les stored

on a card to prepare it for reuse.

Always format a card that has

been previously used in other

devices. Caution! Make sure you

have downloaded and backed

up any les on the card that you

want to preserve rst! Press UP to

select “FO”, press OK, then select

“Y” (Yes) and press OK again to

conrm you want to format the

card. The extra step and “No”

defaults help prevent accidental

erasure of all your photos/videos.

12

When you’ve nished using the Setup Menu, and are ready to return the

camera to normal operating mode, so it will begin to capture photos or

videos for you, simply press the Setup button. After you exit the Setup

Menu, the display will go blank and the camera is in “sleep” mode. About

30 seconds later, the camera will begin taking photos or videos when

triggered, at intervals determined by the trigger delay time setting.

Once your camera has been setup, you are ready to begin using it to

capture photos of activity in the area you choose to locate it. Just follow

these steps:

CAMERA OPERATION

1. Mount the Camera

It is recommended that you mount the camera about 4 or 5 feet (1.2~1.5

meters) o the ground, with the camera pointed at a slight downward

angle. It’s best to avoid mounting the camera facing east or west as the

rising and setting of the sun could produce false triggers and overexposed

images. Clear branches and other debris away from the front of the

camera so as not to block the camera lens or PIR sensor.

To mount the camera in place, insert the strap through the strap slots on

the rear housing. Wrap the strap around the mounting surface. Secure

the strap and tighten the buckle in order to secure the camera.

Make sure that both door latches are securely locked in place, to ensure

proper weather resistance.

2. Power On the Camera

The camera will be in “sleep” status after it has been powered on. When

the PIR sensor is triggered, it will start to take photos immediately after

the delay time (as set) has passed.

13

CAMERA OPERATION (continued)

3. Test the Coverage Area

One of the Trail Camera’s most useful features is the ability to test the

coverage area.

• After mounting the camera, open the front housing and slide

the Power switch to the “ON” position. Press the SETUP button if

necessary to enter the Setup Menu.

• The PIR indicator light below the lens will blink when you have

entered the coverage area.

• Adjust the camera position as needed and repeat the test until the

desired coverage area is achieved.

• Press the SETUP button again when you are nished using the test

mode-the camera will be “sleeping” and waiting for the PIR sensor

to trigger the rst photo or video capture.

• Maximum PIR sensor range is approx. 30 ft.

4. Secure the Camera

A standard padlock may be used in the camera’s lock hole to secure it

and prevent theft.

14

VIEWING THE PHOTOS and VIDEOS

After your camera has been operating for awhile, you will of course want

to review the photos and/or videos it has been capturing. This can be

done by either of two methods, according to your preference or the

availability of accessory equipment:

Using an SD Card Reader

1. Push the SD card in slightly to release it then pull it out gently.

2. Put the SD card into any of the widely available SD card readers

(either a dedicated SD card reader or “multi-card reader” that

features slots for several dierent memory cards, including SD cards.

3. Follow the card reader supplier’s directions to view or download the

photo and/or video les on the SD card.

Connecting the Camera to Your Computer via USB

1. Slide the Power switch to the “ON” position, then press the SETUP

button.

2. Connect your camera’s USB port (left side near the display with

camera unlatched and open) to a PC or Mac computer with a USB

cable (not included, available at most electronics/computer retailers)

that has a “Mini-B” USB plug on one end (camera) and a “Standard-A”

USB plug at the other end (computer).

3. The PC will recognize the camera as an external storage device,

using the “USB Mass Storage” standard (no driver installation

necessary-not compatible with Windows 98 or earlier). The PC will

display a new disk symbol under “My Computer” or in Windows

Explorer (Macs-new disk appears on the desktop), and you will see a

dialog window on your desktop with several options to view, move,

or copy the photo and video les that are stored on the SD card.

The camera’s LCD will display “STO”, meaning the camera is in mass

storage mode.

15

PIR (Passive Infrared Sensor): Senses motion like a typical security motion

detector. Requires infrared energy (heat) in addition to motion to trigger

the sensor to help limit detection to live subjects (rather than leaves, etc).

Camera Delay: Time elapsed between photos while events are sensed

and recorded. You should set this based on wildlife activity in the area.

Moon Phase: The trail cams have a feature which imprints a moon phase

stamp on each photo for reference.

IR Flash: Also called IR LED Array. This is a “night vision” feature, which

emits a burst of infrared light, invisible to the human eye. Especially

useful for night photos when a visible ash may be undesirable.

Battery Life: Time that camera will function in the eld. Dependent on

ambient temperature, number of images taken and number of times the

IR ash res. When the battery voltage drops below 4.5v, the IR ash stops

ring. When battery voltage is below 3.5v, the camera stops working.

Single/Multi-Image Modes: The number of pictures the camera takes

per PIR trigger (still photo capture mode only).

1P: A single image is captured for each PIR trigger

3P: A three image sequence captured for each PIR trigger

FULL: When the SD card’s memory capacity is full, the LCD display

indicates “FULL”

Mass Storage: Connect the camera with a USB cable to a computer,

press the “SETUP” button, and the computer can access the contents of

the SD card. The camera is automatically recognized as an “external drive”,

without the need to install special drivers. (Win 98 and older operating

systems are not supported. Mac OSX is also compatible-the camera will

appear on your desktop as an external storage device or “disk”).

GLOSSARY

16

Technical Specications

Model Number 119256CW

Image Sensor Type 1/4 Inch CMOS

Sensor Resolution 1.3 Megapixels

Eective Focal Length 7.6 mm

Lens Aperture f/2.0

IR Filter Automatic IR Filter

Display LCD (menu screen)

PIR Sensor Yes

Trigger Speed 1.3 seconds or less

Number of IR LED 15 LEDs

Max Night Vision Lighting Distance 30 feet

Storage SD Card, up to 32 GB Capacity

PIR Indicator Yes (Setup mode only)

Adjustable Delay Time Range 5~ 59 second, 1~ 10mins (default 10S)

Selectable Image Resolution LO (1.3 MP) or HI (3 MP*)

Multiple Image Mode Yes-3 photos

Video Resolution

Movie: AVI 640 x 480 pixels @ 30 fps (5-60

seconds).

File Format (Image/Video) JPEG/AVI

Date/Time Imprint Yes

Moon Phase Imprint Yes

Exposure Auto

White Balance Mode Auto

Power Supply 4 AA Cell batteries (alkaline or lithium)

Water Resistant Yes

*3MP resolution via software interpolation

17

Battery life is shorter than expected

1. Battery life will vary with operating temperature and the number

of images taken over time. Typically, the trail cam will be able to

capture several thousand images before the batteries die.

2. Check to make sure you have used new alkaline or lithium

batteries. Tasco recommends using 4 Energizer® Lithium AA

batteries in this Trail Cam to obtain maximum battery life.

3. Make sure that the power switch was turned to the “ON” position

and that the camera was not left in Setup mode while in the eld.

4. Make sure that you are using a good quality name brand SD card

in your camera. Tasco recommends SanDisk® brand SD Cards

up to 32GB. Our experience indicates that poor quality SD cards

can sometimes reduce your trail cam battery life.

Camera stops taking images or won’t take images

1. Please make sure that the SD card is not full. If the card is full, the

camera will stop taking images.

2. Check the batteries to make sure that they are new alkaline or

lithium AA batteries. See note above about short battery life.

3. Make sure that the camera power switch is in the “ON” position

and not in the “OFF” position or in Setup mode.

4. Make sure that you are using a good quality SD card in your

camera. Tasco recommends SanDisk® SD Cards up to 32GB.

5. If the SD card has its write protect switch in the lock position, the

camera will not take images.

6. If you have used an SD card in another device before inserting

it in your trail cam , you might want to try formatting the card

using the “Format” parameter in Setup mode (make sure you

have backed up any important les rst, as formatting will erase

all previous les). In some cases, other devices may change the

formatting of the SD card so that it will not work properly with

the trail cam .



Troubleshooting / FAQ

18

Camera won’t power up

1. Make sure that you have installed all 4 batteries in the battery

compartment. Tasco recommends using 4 Energizer® Lithium

AA batteries in this trail cam .

2. Make sure that the batteries are installed correctly, observing

proper polarity. Always place the negative (at) end of each

battery in contact with the spring tab side of its slot inside the

camera.

Still Photo and/or Video Quality Problems

1. Night photos or videos appear too dark

a. Try using a set of new batteries. The ash will stop operating

near the end of the battery life.

b. You will get the best results when the subject is within the

ideal ash range, no farther than 30’ from the camera. Subjects

may appear too dark at greater distances.

c. Please note that when the still photo mode is set to “3P”, or with

very short Delay time settings, some images may appear darker

than others due to the quick response and rapid retriggering

of the camera, allowing less time for the ash to fully recharge

before ring again.

2. Daytime photos or videos appear too dark

a. Make sure that the camera is not aimed at the sun or other

light sources during the day, as this may cause the auto exposure

to produce darker results.

3. Night photos or videos appear too bright

a. You will get the best results when the subject is within the

ideal ash range, no closer than 10’ (3m) from the camera.

Subjects may appear too light at closer distances.

4. Daytime photos or videos appear too bright

a. Make sure that the camera is not aimed at the sun or other

light sources during the day.

Troubleshooting / FAQ

Do not mix old and new batteries.

Do not mix battery types-use ALL lithium or ALL alkaline.

Rechargeable batteries are not recommended.

19

5. Photos with streaked subject

a. In some cases with low lighting conditions and fast moving

subjects, the 3 MP resolution setting (“HI”) may not perform as

well as the 1.3 MP setting (“LO”).

b. If you have multiple images where fast moving subjects

produce streaks on the photo, try the “LO” resolution setting

instead.

6. Red , green or blue color cast

a. Under certain lighting conditions, the sensor can become

confused resulting in poor color images.

b. If this is seen on a consistent basis, then the sensor may need

servicing. Please contact Tasco customer service.

7. Short video clips—not recording to the length set

a. Check to make sure that the SD card is not full.

b. Make sure that the camera has good batteries in it. Near the

end of the battery life, the camera may choose to record shorter

video clips to conserve power.

Photos Do Not Capture Subject of Interest

1. Try to set your camera up in an area where there is not a heat

source in the camera’s line of sight.

2. In some cases, setting the camera near water will make the

camera take images with no subject in them. Try aiming the

camera over ground.

3. Try to avoid setting the camera up on small trees that are prone

to being moved by strong winds.

4. Remove any limbs which are right in front of the camera lens.

PIR Sensor LED Flashes/Doesn’t Flash

1. When the camera is in the “Setup” mode, the PIR Indicator LED

on the front of the camera will ash when it senses motion. This

is for setup purposes only and will help the user aim the camera.

2. During use, the LED will not ash when the camera takes an

image. This is to help keep the camera hidden from game.

Troubleshooting / FAQ

20

Camera won’t retain settings

1. Make sure that you have been saving the changes to any parameter

settings that you made while in Setup mode, by pressing “OK”

after changing the setting. If you don’t save your new setting after

changing it, the camera will continue to use the original default

setting for that parameter.

Troubleshooting / FAQ

Do not mix old and new batteries.

Do not mix battery types-use ALL lithium or ALL alkaline.

Rechargeable batteries are not recommended.

La page charge ...

Tasco 119256CW Manuel utilisateur

Tasco 119256CW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents