Simplicity 030805-00 Manuel utilisateur

Marque: Simplicity

Modèle: 030805-00

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

030805-01

Manual No. 80088710 Revision A

Outdoor Portable Generator

Operator’s Manual

Model Number _____________________________

Revision __________________________________

Serial Number ______________________________

Date Purchased ____________________________

800-743-4115

BRIGGSandSTRATTON.COM

2 BRIGGSandSTRATTON.COM

Equipment Description

Table of Contents

Equipment Description.........................2

Features and Controls .........................5

Operation....................................7

Maintenance ................................14

Storage ....................................17

IC Information to User ........................17

Troubleshooting/Specifications .................18

Warranty ...................................20

To ensure prompt and complete warranty coverage, register

your product online at www.onlineproductregistration.com.

Symbols and Meanings

Signal Meaning

DANGER

Indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION

Indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE

Indicates information considered important, but

not hazard-related.

Symbol Name Explanation

Safety Alert

Symbol

Indicates a potential personal injury

hazard.

Operator’s

Manual

Failure to follow warnings, instructions

and operator’s manual could result in

death or serious injury.

Toxic Fumes

Engine exhaust contains carbon

monoxide, a poisonous gas that

will kill you in minutes. You cannot

smell it or see it.

Fire

Fuel and its vapors are extremely

flammable which could cause

burns or fire resulting in death or

serious injury.

Engine exhaust could cause fire

resulting in death or serious injury.

Electric

Shock

Generator could cause electrical

shock resulting in death or serious

injury.

Hot Surface

Muffler could cause burns or

resulting in serious injury.

WARNING! This product can expose you to

chemicals including gasoline engine exhaust, which

is known to the State of California to cause cancer,

and carbon monoxide, which is known to the State of

California to cause birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

Equipment Description

Read this manual carefully and become familiar

with your outdoor generator. Know its applications,

its limitations, and any hazards involved. Save

these original instructions for future reference.

The outdoor generator is an engine–driven, revolving

field, alternating and direct current (AC & DC) generator.

It was designed to supply electrical power for operating

compatible electrical lighting, appliances, tools and motor

loads. The generator’s revolving field is driven by a single-

cylinder engine.

To move generator, press button and pull handle out.

Press button to push handle back in.

The portable generator can be used to power outdoor items

using extension cords or for providing power to your travel trailer/

recreational vehicle (RV). DO NOT connect generator to a home’s

electrical system.

The generator is not intended to supply systems that are

legally required, for serious life safety or health hazards,

or where lack of power hampers rescue of fire-fighting

operations.

Every effort has been made to ensure that the information in this

manual is both accurate and current. However, the manufacturer

reserves the right to change, alter or otherwise improve the

generator and this documentation at any time without prior notice.

NOTICE If you have questions about intended use, contact an

authorized service dealer. This equipment is designed to be used

with Briggs & Stratton® authorized parts only.

System Ground

The generator neutral is floating, which means that the

neutral wire is isolated from the grounding fastener and the

AC receptacle ground pins. On a floating neutral generator

the AC receptacle ground pins are not functional. Electrical

devices, such as a GFCI, requiring a functioning AC

receptacle ground pin will not operate.

Special Requirements

There may be federal or state regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector,

or the local agency having jurisdiction.

This generator is not intended to be used at a construction

site or similar activity as defined by NFPA 70-2017 (NEC)

section 590.6.

Equipment Description

Connect Battery

You must connect the battery to the generator to enable

electric or remote starting. The display panel, LED’s and

e-choke system are powered by the battery also.

1. Remove screw and panel from in front of the battery.

2. Connect the two pin connector from the battery to the

generator.

Pairing Remote Start Fob to the Generator

The remote start fob needs to be paired with the generator

to remotely start your generator. To pair the fob with the

generator, follow the instructions below:

1. Press and hold the activate switch for 10 seconds and

the on/off button light will begin to flash blue.

2. Within 30 seconds, press and hold either button on

the remote start fob for 2 seconds. The on/off button

light will blink rapidly 3 times signaling the remote start

fob has been paired.

NOTICE All remote start fobs can be disconnected by

pressing both the on/off button and activate switch on the

generator at the same time for 10 seconds.

InfoHub™ Portable Wireless App

Download the InfoHub Portable App* to pair the

Bluetooth® enabled generator to your approved Android or

iOS smartphone and follow the in app instructions.

The generator is equipped with a status LED (located

under QPT button) to indicate the Bluetooth status. A

blinking blue LED indicates the generator is ready to be

paired to the App on your smartphone. A solid blue LED

indicates your generator is connected to the App on your

smartphone. A red LED indicates a fault in the generator’s

Bluetooth system, contact your closest Briggs & Stratton

authorized service dealer.

The InfoHub Portable App allows you to access information

about your generator directly through your smartphone.

The power usage displayed in the app is a percentage of

total generator output. Each receptacle is limited by the

receptacles capacity and circuit breaker. See Connecting

Electrical Loads.

* Data rates apply

The Bluetooth® word mark and logos are registered trademarks owned

by the Bluetooth SIG, Inc. and any use of such marks by Briggs & Stratton

is under license. Other trademarks and trade names are those of their

respective owners.

Activate Switch

On/Off Button

4 BRIGGSandSTRATTON.COM

Equipment Description

Activate Switch — Push to turn on the generator display.

Air Cleaner — Filters engine intake air.

Battery Cover — Remove to gain access to the battery.

Choke Lever — Used when manually starting a cold engine.

Fuel Cap — Add unleaded fuel here.

Fuel Valve — Used to turn fuel supply on and off to engine.

Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

Hour Meter — The LED displays and records how many

hours your generator has run (up to 999.9).

Identification Label — Provides model and serial number of

generator.

Low Oil Indicator — This unit is equipped with a low oil

protection device. Oil must be at proper level for engine

to run. If the engine oil drops below a preset level, an oil

switch will stop the engine. Check oil level with dipstick.

Maintenance Cover — Remove to gain access to the

choke lever, spark plug and air cleaner.

Oil Drain Plug — Drain engine oil here.

Oil Fill Cap/Dipstick — Check and add engine oil here.

Oil Service Cover — Remove to gain access to the oil fill

and drain.

On/Off Button — Push and hold for one second to start or

stop generator.



this button to turn off the QPT.

Recoil Starter — Used to start the engine manually.

Retractable Handle — Press button and pull handle out to

move generator. Press button to push handle back in.

Spark Arrester Muffler/Exhaust — Lowers engine noise and

is equipped with a spark arrester screen.

Fuel Cap

Grounding Fastener

Choke Lever (under cover)

Air Cleaner (under cover)

Maintenance Cover

Battery Cover

Oil Fill Cap/Dipstick (under cover)

Oil Drain Plug (under cover)

Identification Label

Fuel Valve

Recoil Starter

Spark Arrester Muffler/Exhaust

Retractable Handle

Low Oil Indicator

QPT Button

Oil Service Cover

Hour Meter

Activate Switch

On/Off Button

Features and Controls

120 Volt AC, 20 Amp, Duplex Receptacles — Used

to supply 120 Volt AC, single phase, 60 Hz power for

electrical lighting, appliance, tool and motor loads.

120 Volt AC, 30 Amp Travel Trailer Receptacle — May

be used to supply electrical power for the operation of

120 Volt AC, 30 Amp, single phase, 60 Hz electrical, travel

trailer loads.

Circuit Breakers (AC) — Push-to-reset circuit breakers

are provided to protect the generator against electrical

overload.

Carbon Monoxide (CO) Shutdown Indicator Light —

Indicates the engine shutdown due to carbon monoxide

accumulation around the generator or a CO shutdown

system fault occurred.

USB Ports — Use ports to recharge most USB powered

devices.

Compare the illustrations with your generator to familiarize yourself with the locations of various controls and product warnings.

120 Volt AC, 30 Amp

Travel Trailer Receptacle

120 Volt AC, 20 Amp

Duplex Receptacles

Circuit Breakers

Carbon Monoxide

(CO) Shutdown

Indicator Light

USB Ports

6 BRIGGSandSTRATTON.COM

Exhaust/muffler

Point away from home

Features and Controls

Operation

Step 1: Safe Location

Before starting the portable generator there are two equally

important safety concerns regarding carbon monoxide

poisoning and fire that must be addressed.

Operation Location to Reduce the Risk of

Carbon Monoxide Poisoning

The engine exhaust of all fossil fuel burning equipment,

such as a portable generator, contains carbon monoxide,

a poisonous gas that will kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

By law it is required in many states to have a carbon

monoxide alarm in operating condition in your home. A

carbon monoxide alarm is an electronic device that detects

hazardous levels of carbon monoxide. When there is

a buildup of carbon monoxide, the alarm will alert the

occupants by flashing visual indicator light and alarm.

Smoke alarms cannot detect carbon monoxide gas.

DANGER! Engine exhaust contains carbon

monoxide, a poisonous gas that will kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Operate portable generator only outdoors, at least

20 ft. (6.1 m) from occupied spaces with exhaust

pointed away to reduce the risk of carbon monoxide

accumulating.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• Do not run portable generator inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

If you start to feel sick, dizzy, weak, or your homes carbon

monoxide alarm sounds while using this product, get to

fresh air right away. Call emergency services. You may

have carbon monoxide poisoning.

To better educate yourself about all carbon monoxide risks,

go to www.takeyourgeneratoroutside.com.

20 ft.

(6.1 m) min.

Carbon Monoxide Alarm(s)

Install carbon monoxide alarm

inside your home. Without

working carbon monoxide

alarms, you will not realize you

are getting sick and dying from

carbon monoxide poisoning.

Prevent Carbon Monoxide (CO) Poisoning

• Use outdoors at least 20 ft. (6.1 m) from any home.

• Point exhaust away from all homes and occupied spaces.

• Install CO alarms inside your home.

8 BRIGGSandSTRATTON.COM

Operation

MUFFLER

5 ft. (1.5 m) min.

20 ft. (6.1 m) min.

5 ft. (1.5 m)

min.

Operation Location to Reduce the Risk of Fire

WARNING!

Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a fire, resulting in death or serious injury.

• Portable generator must be at least 5 ft. (1.5 m) from any

structure, overhang, trees, shrubs, or vegetation over 12

in. (30.5 cm) in height.

• Do not place portable generator under a deck or other

type of structure that may confine airflow. Smoke alarm(s)

must be installed and maintained indoors according to the

manufacturer’s instructions/recommendations.

• Carbon monoxide alarms cannot detect smoke.

• Do not place portable generator in manner other than

shown.

Step 2: Oil and Fuel

1. Move generator outdoors to a flat, level surface.

2. Turn dial and open cover over oil fill area.

3. Clean area around oil fill and remove oil fill cap/dipstick.

4. Using an oil funnel, slowly pour contents of oil bottle

into oil fill opening. Checking oil level frequently, fill to

point of overflowing.

NOTICE Do not screw in dipstick when checking oil level.

NOTICE Pause to permit oil to settle. Wipe dipstick clean

each time oil level is checked. DO NOT overfill.

5. Replace and fully tighten oil fill cap/dipstick.

6. Replace cover over oil fill area.

Low Oil Indicator

The low oil indicator system is designed to prevent engine

damage caused by not enough engine oil. If engine oil level

drops below a preset level, the red LED low oil indicator light

comes on and an oil level switch will stop the engine. If engine

stops or the red LED low oil indicator light comes on when

you try to start the generator, check the engine oil level.

Fuel must meet these requirements:

• Clean, fresh, unleaded fuel with a minimum of 87 octane.

• Gasoline with an ethanol content up to 10% is acceptable.

E10

E15

NOTICE Do not mix oil in fuel or modify engine to run on

alternate fuels. Use of unapproved fuels could damage

engine and will not be covered under warranty.

See High Altitude for 5,000 ft. and above.

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious injury.

• Do not refuel during operation.

• Do not smoke during refueling.

• Turn engine off and let it cool at least 2 minutes before

removing fuel cap.

• Fill fuel tank outdoors. Keep fuel away from sparks, open

flames, pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

7. Slowly remove fuel cap to relieve pressure in tank.

8. Slowly add unleaded fuel to red max fill indicator in fuel

tank. Be careful not to fill above the indicator. This allows

adequate space for fuel expansion.

9. Install fuel cap and let any spilled fuel evaporate

before starting engine.

High Altitude

At altitudes over 5,000 ft. (1524 m), a minimum 85 octane

fuel is acceptable. To remain emissions compliant, high

altitude adjustment is required. Operation without this

adjustment will cause decreased performance, increased

fuel consumption,

and increased emissions.

See an authorized Briggs & Stratton dealer for high altitude

adjustment information. Operation of the engine at altitudes below

2,500 ft. (762 m) with the high altitude kit is not recommended.

Transporting

When transporting equipment, turn fuel valve to off

( )

position. Do not tip engine or equipment at an angle which

causes fuel to spill.

Operation

Max Fill Indicator

Oil Fill Cap/

Dipstick

10 BRIGGSandSTRATTON.COM

Operation

Step 3: Generator Start Up

Turn off all electrical loads connected to the generator. Use the

following start instructions:

1. Make sure unit is outdoors on a level surface.

NOTICE Failure to operate the unit on a level surface may

cause the unit to shut down.

2. Turn fuel valve clockwise to the on

( )

position.

Wireless Remote Starting

3. Press and hold on/off ( ) button for one second on

remote start fob to activate generator.

4. Within 5 seconds, pressand hold start ( ) buttonfor

one second. The on/off button on generator will blink

blue when a signal is received and generator will start.

NOTICE If the generator failed to start, the generator on/

off button will turn red for 5 seconds, then blink green for

up to one minute. Repeat step 4.

Manual or Electric Starting

3. Press the activate switch (

) to turn on the display.

The on/off button (

) will blink green for up to one

minute.

NOTICE If the on/off button doesn’t blink green, the

battery is not connected or too low to start the generator.

NOTICE This unit is equipped with an e-choke system.

An e-choke system means there is no manual priming or

choking required as long as the battery is connected and

charged.

4A. For electric starting; press and hold on/off button

(

) for one second while it’s blinking green to start

generator. Once generator starts, on/off button will

turn blue indicating generator is ready for use.

NOTICE If generator failed to start, on/off button will turn

red for 5 seconds, then blink green for up to one minute.

Repeat step 4A.

4B. For manual starting; grasp recoil and pull slowly until

slight resistance is felt. Then pull rapidly to start engine.

The e-choke may still engage with a low battery.

NOTICE If generator continues not to start, your battery

may be discharged too low and you will need to manually

choke the engine. Remove the maintenance cover and

position the choke lever to the choke position (to the right

as shown). The e-choke will automatically turn the choke

off once the generator starts. Reinstall maintenance cover.

NOTICE If engine starts but fails to run, see Low Oil Indicator.

Remote Start Lockout

The remote start can be locked out so that your generator

can not be started remotely. To lock out remote start, press

the activate switch (

) to turn on the display, then press

and hold on/off button on generator for 10 seconds. The

on/off light will then blink red three times signifying remote

start function is locked out. To unlock, repeat.

Pressing either button on the remote start fob, the on/off

button will blink red 3 times when locked and will blink blue

3 times when unlocked.

Choke Lever

Fuel Valve

On/Off Button

Activate Switch

On/Off Button

Start Button

Operation

Step 4: Connecting Electrical Loads

Using Extension Cords

1. Only use grounded cords marked for outdoor use

rated for your loads.

To provide power using

extension cords

Total

Amperage

Minimum Guage, Outdoor Rated

Up to 50 FT (15 M) Up to 100 FT (30 M)

Up to 13A

Up to 15A

Up to 20A

Up to 30A

2. Follow cord safety instructions.

3. Install carbon monoxide alarm(s).

4. When operating generator with extension cords, make

sure it is located in an open, outdoor area, at least 20

ft. (6.1 m.) from occupied spaces with exhaust pointed

away.

5. Extension cords running directly into home, powering

indoor items IS NOT RECOMMENDED.

DANGER! Engine exhaust contains carbon

monoxide, a poisonous gas that will kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Extension cords running directly into the home

increase your risk of carbon monoxide poisoning

through openings.

• If an extension cord running directly into the home is

used to power indoor items, the operator recognizes

that this increases the risk of CO poisoning to people

inside the home and assumes that risk.

WARNING! Damaged or overloaded extension

cords could overheat, arc, and burn resulting in

death or serious injury.

NOTICE For generator output required see Generator

Capacity. Connect electrical loads in off position then turn

on for operation.

5 Volt DC USB Ports

The maximum combined current available for the USB

ports is 2.1 Amps at 5 Volts. The USB port allows you to

recharge most USB powered devices with a USB charging

cable (not included).

NOTICE For maximum output, use the bottom USB port.

NOTICE For charging ITE (Information Technology

Equipment) only.

120 Volt AC, 20 Amp, Duplex Receptacles

Use each receptacle to operate 120 Volt AC, single-phase,

60 Hz electrical loads requiring up to 2,400 Watts (2.4 kW)

at 20 Amps of current.

120 Volt AC, 30 Amp, Travel Trailer Receptacle

Use a NEMA TT–30 plug with this receptacle. Connect a

3–wire travel trailer cord set rated for 125 Volt AC loads at

30 Amps to the plug.

This receptacle powers 120 Volt AC, 60 Hz, single phase

travel trailer loads requiring up to 3,600 watts (3.6 kW) of

power at 30 Amps.

Duplex

Receptacles

USB Ports

Travel Trailer

Receptacle

12 BRIGGSandSTRATTON.COM

Tool or Appliance Running Watts Starting Watts

Window AC - 10000 BTU

1000 2100

Refrigerator/Freezer 550 1350

Plasma Television 500 —

Light (75 Watts) 75 —

2125 Total

Running Watts

2100 Highest

Starting Watts

Tool or Appliance

Running

Watts*

Starting

Watts**

Light Bulb - 75 Watt 75 -

Refrigerator/Freezer 550 1350

Window AC - 10,000 BTU 1000 2100

Microwave Oven - 1000 Watt 1000 -

Plasma Television - 50” 500 -

Laptop 250 -

Power Use

The power use monitor indicates percentage of total generator

load using LED’s. The first green LED indicates generator

is operating normally or producing more than 5% load. The

fourth green LED comes on after 50% load is reached. The last

yellow LED comes on after 100% load is reached.

Output Indicator

The green LED output indicator light comes on when

the generator is operating normally. It indicates that the

generator is producing power at the receptacles. It will also

start flashing red if you start to overload the generator.

Overload Alarm

The red LED overload alarm light comes on and cuts

power to the receptacles if you overload the generator.

The output indicator light will also go off. If the generator

was overloaded, you must turn off and unplug all electrical

loads, press the MAIN RESET button on the generator

control panel and then plug in and restart electrical loads

one at a time to continue in normal operating mode.

QPT (QUIET POWER TECHNOLOGY)

This feature is designed to greatly improve fuel economy.

The QPT will automatically come on when the generator is

started. To turn off, press QPT button.

When QPT is on, engine speed increases as loads are

connected, and decreases as loads are removed.

When QPT is off, engine will run at full governed speed.

Generator Capacity

To make sure your generator can supply enough running

watts and starting watts for the items you will power at the

same time, follow these three simple steps:

1. Select the items you will power at the same time. See

following list for typical wattages.

* Typical wattages listed are approximate only. Check tool

or appliance for actual wattage.

** The momentary electrical current the generator can

provide to start electric motors, per Briggs & Stratton

standard 628K. It does not represent the power required to

continuously run electrical loads. It is the maximum current

that can momentarily be supplied when starting a motor,

multiplied by the generator’s rated voltage.

2. Total the running watts. This is the amount of power

your generator must produce to keep your items

running. See following example:

Example

Total running watts = 2125

Highest starting watts = 2100

Total generator watts required = 4225

3. Estimate the starting watts you will need. Because not

all motors start at the same time, total starting wattage

can be estimated by adding only the item with the

highest additional starting watts requirements to the

total running watts from step 2.

Output

Indicator

Main Reset

Power Use

Monitor

Overload Alarm

Fuel

Level

Monitor

QPT Button

Operation

Power Management

To manage generator power, sequentially add loads as

follows:

1. With nothing connected to generator, start the engine

outdoors.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider starting watts in generator capacity.

Carbon Monoxide (CO) Shutdown System

Automatically shuts down the engine when harmful levels

of carbon monoxide accumulate around the generator or

a CO shutdown system fault occurs. After shutdown, the

indicator light will blink for at least five minutes per the

chart below.

The CO shutdown system DOES NOT replace carbon

monoxide alarms. Install battery-powered carbon monoxide

alarm(s) in your home. Do not run generator in enclosed

areas.

Color/Pattern Description

Red

•• ••

Carbon monoxide accumulated around

generator. Move generator to an

open, outdoor area 20 ft. (6.1 m) from

occupied spaces with exhaust pointed

away. Automatic shutoff is an indication

generator was improperly located. Air

out premises (e.g. open windows and

doors) before reoccupying.

If you start to feel sick, dizzy, weak, or

your homes carbon monoxide alarm

sounds while using this product, get to

fresh air right away. Call emergency

services. You may have carbon

monoxide poisoning.

Blue

• • •

CO shutdown system fault occured*.

See Briggs & Stratton authorized service

dealer.

*Blue light will blink for five seconds at the startup of generator to

show the CO shutdown system is functioning properly.

Step 5: Generator Shutdown

1. Turn off and unplug all electrical loads from generator

panel receptacles. Never stop engine with electrical

devices plugged in and turned on.

2. Let engine run at no-load for one minute to stabilize

internal temperatures of engine and generator.

3. Press the on/off button on the generator or either

button on the remote start fob.

Operation

14 BRIGGSandSTRATTON.COM

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

Service more often under dirty or dusty conditions.

See any authorized dealer for service.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See any Briggs & Stratton

Authorized Service Dealer for maintenance and service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain the generator as instructed in this manual.

All service and adjustments should be made at least once

each season. A new spark plug and clean air filter assure

proper fuel-air mixture and help your engine run better and

last longer. Follow requirements in Maintenance Schedule.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See Emissions Warranty.

• Generator is equipped with a G-trim engine.

Cleaning

Daily or before use, look around and underneath

the generator for signs of oil or fuel leaks. Clean any

accumulated debris. Keep area around muffler free from

any debris.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE Improper treatment of generator could damage

it and shorten its life. Do not expose generator to excessive

moisture, dust, dirt, or corrosive vapors. Do not insert any

objects through cooling slots.

Battery Maintenance

The generator is equipped with an automatic battery

charging circuit that charges the battery while the engine

is running. If the generator isn’t used frequently, the

battery should be connected to a trickle charger or battery

maintainer (not included) to keep it properly charged.

1. Remove panel from in front of the battery.

2. Disconnect the two pin connector from the battery to

the generator.

NOTICE Do not exceed 1.5 Amp charging rate.

3. Follow the instructions included with the trickle

charger or battery maintainer.

Remote Start FOB Batteries

Follow the instructions below if you need to replace the

batteries in the remote start fob:

1. Loosen and remove screws from cover, then remove

cover.

2. Remove the discharged batteries and insert two new

CR2016 lithium batteries with the “+” terminal facing

up.

3. Reinstall the cover and screws and tighten.

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

Every 50 Hours or Yearly

• Clean engine air cleaner

Every 100 Hours or Yearly

• Change engine oil

• Service spark plug

• Inspect muffler and spark arrester

1, 2

• Check/Adjust valve clearance

• Clean fuel tank and filter

Every 250 Hours

• Clean combustion chamber

1, 2

Maintenance

Engine Maintenance

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity

for the engine. Use the chart to select the best viscosity for

the outdoor temperature range expected. Engines on most

outdoor power equipment operate well with 5W30 Synthetic

oil. For equipment operated in hot temperatures, Vanguard®

15W50 Synthetic oil provides the best protection.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

Checking/Adding Engine Oil

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure generator is on a level surface.

2. Remove cover over the oil fill area.

3. Clean area around oil fill, remove dipsitck and wipe

with clean cloth. Replace dipstick. Remove and check

oil level.

NOTICE Do not screw in dipstick when checking oil level.

4. Verify oil is at full mark on dipstick.

5. If needed, slowly pour oil into oil fill opening to the

point of overflowing.

6. Replace and tighten dipstick.

NOTICE Do not attempt to crank or start engine before

it has been properly serviced with recommended oil. This

could result in an engine failure.

7. Replace cover over oil fill area.

CAUTION Avoid prolonged or repeated skin contact

with used motor oil. Used motor oil has been shown

to cause skin cancer in certain laboratory animals.

Thoroughly wash exposed areas with soap and water.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Changing Engine Oil

If you are using your generator under extremely dirty or

dusty conditions, or in extremely hot weather, change the

oil more often.

Change the oil while the engine is still warm from running,

as follows:

1. Make sure unit is on a level surface.

2. Remove cover over the oil fill area.

3. Remove oil drain plug and drain oil completely into a

suitable container.

4. Reinstall oil drain plug and tighten securely. Remove

dipstick.

5. Slowly pour recommended oil (about 20 oz. (0.6 l))

into oil fill opening. Pause to permit oil to settle. Fill to

Full mark on dipstick.

6. Wipe dipstick clean each time oil level is checked. Do

not overfill.

7. Reinstall dipstick. Tighten cap securely.

8. Wipe up any spilled oil.

9. Replace cover over oil fill area.

Service Air Cleaner

WARNING! Fuel and its vapors are extremely

flammable which could cause burns or fire

resulting in death or serious injury.

• Do not start and run engine with air filter removed.

Your engine will not run properly and may be damaged

if you run it with a dirty air cleaner. Service more often if

operating under dirty or dusty conditions.

Oil Drain

Plug

16 BRIGGSandSTRATTON.COM

Maintenance

1. Loosen the two maintenance cover screws and

remove the maintenance cover.

2. Remove three air cleaner cover screws and slide air

cleaner assembly out.

3. Carefully remove foam air cleaner from the assembly.

4. Carefully remove breather filter from the base by

pulling it out towards you.

5. Wash foam air cleaner and breather filter in liquid

detergent and water only. Squeeze dry in a clean

cloth.

6. SATURATE foam air cleaner in clean engine oil and

squeeze in a clean cloth to remove excess oil.

7. Reinstall clean or new foam air cleaner inside

assembly.

8. Reinstall clean or new breather filter inside base.

9. Slide air cleaner assembly into base and tighten

screws.

10. Reinstall the maintenance cover and hand tighten the

cover screws.

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Loosen the two maintenance cover screws and

remove the maintenance cover.

2. Clean area around spark plug and remove spark plug

boot.

3. Remove spark plug and inspect spark plug.

4. Replace spark plug if electrodes are pitted, burned

or porcelain is cracked. Use the recommended

replacement spark plug. See Common Service Parts.

5. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary

(see Specifications).

6. Install spark plug and tighten firmly. Reinstall spark

plug boot.

7. Reinstall maintenance cover and hand tighten screws.

Inspect Spark Arrester

Inspect spark arrester for damage or carbon blockage. If

damage is found or cleaning is needed, see a Briggs &

Stratton Authorized Service Dealer.

WARNING!

Contact with muffler area could

cause burns resulting in serious injury.

• Do not touch hot parts.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined

in Section 4442, maintained in effective working order.

Other states or federal jurisdictions may have similar laws,

reference Federal Regulation 36 CFR Part 261.52.

Common Service Parts

Air Cleaner ...........................84001978

Breather Filter. . . . . . . . . . . . . . . . . . . . . . . . . 84001981

Spark Plug ...........................84001980

Engine Oil Bottle ........................100028

Synthetic Oil Bottle ......................100074

Contact an authorized service dealer or

BRIGGSandSTRATTON.com for a full list of parts and

diagrams.

Air Cleaner

Breather Filter

Screws

Storage

If storing the unit for more than 30 days, use the following

guidelines to prepare it for storage.

Long Term Storage Instructions

1. Clean the generator as outlined in Cleaning.

2. Change engine oil while engine is still warm, drain oil

from crankcase. Refill with recommended grade. See

Changing Engine Oil.

3. Treat or drain fuel from generator as fuel can become

stale when stored over 30 days.

Each time you fill the container with fuel, add STA-BIL

360°® PROTECTION™ to the fuel as specified by the

manufacturer’s instructions. This keeps fuel fresh and

decreases fuel-related problems or contamination in the

fuel system.

It is not necessary to drain fuel from the engine when STA-

BIL 360°® PROTECTION™ is added as instructed. Before

storage, turn the engine ON for 2 minutes to move the fuel

and stabilizer through the fuel system.

If fuel in the engine has not been treated with STA-

BIL 360°® PROTECTION™, it must be drained into an

approved container. Then run the engine until it stops from

lack of fuel.

WARNING!

Fuel and its vapors are extremely

flammable and explosive which could cause

burns, fire or explosion resulting in death or

serious injury.

• When storing fuel or equipment with fuel in tank, store

away from furnaces, stoves, water heaters, clothes dryers

or other appliances that have pilot light or other ignition

source because they could ignite fuel vapors.

• When draining fuel, turn generator engine off and let it

cool at least 2 minutes before removing fuel cap. Loosen

cap slowly to relieve pressure in tank. Drain fuel tank

outdoors. Keep fuel away from sparks, open flames, pilot

lights, heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

4. Turn fuel valve counterclockwise to the off

( )

position.

5. Charge battery as outlined in Battery Maintenance.

6. Store generator in clean, dry area and cover with a

suitable protective cover that does not retain moisture.

WARNING! Storage covers could cause a fire

resulting in death or serious injury.

• Do not place a storage cover over a hot or running

generator. Let equipment cool for a sufficient time before

placing the cover on the equipment.

IC Information to User

This device complies with Industry Canada’s licence-

exempt RSSs. Operation is subject to the following two

conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including

interference that may cause undesired operation of device.

This spark ignition system complies with the Canadian

standard CAN ICES-2/NMB-2.

18 BRIGGSandSTRATTON.COM

Troubleshooting/Specifications

Problem Cause Correction

Engine is running, but no AC

output is available.

1. One of the circuit breakers is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

4. Red LED light is steady. Generator is

overloaded or overheated.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in

good condition.

4. See Generator Capacity. Press

MAIN RESET button on control

panel.

Engine runs well at no-load but

“bogs down” when loads are

connected.

1. Generator is overloaded. 1. See Generator Capacity.

Engine will not start; starts and

runs rough or shuts down when

running.

1. Fuel valve is in off

( )

position.

2. Low oil indicator light comes on. Low

oil level.

3. Dirty air cleaner.

4. Out of fuel.

5. Spark plug wire not connected to

spark plug.

6. Flooded with fuel.

7. Battery not connected or discharged.

1. Turn fuel valve to on

( )

position.

2. Fill crankcase to proper level or

place generator on level surface.

3. Clean or replace air cleaner.

4. Fill fuel tank.

5. Connect wire to spark plug.

6. Wait 5 minutes and re-crank engine.

7. Connect or charge battery.

Engine shuts down and CO

shutdown system LED blinks red

(•• ••).

1. Generator improperly located.

1. Move generator to an open,

outdoor area. Air out premises (e.g.

open windows and doors) before

reoccupying. See Carbon Monoxide

(CO) Shutdown System.

For all other issues, see a Briggs & Stratton authorized dealer.

Specifications

Rated Wattage* ........................................... 3,700

Starting Wattage** ......................................... 4,500

AC Current at 120 Volts ................................30.8 Amps

Frequency. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Hz

Phase .............................................Single Phase

Displacement .................................13.7 cu. in. (224 cc)

Spark Plug Gap ........................0.028-0.031 in. (0.7-0.8 mm)

Fuel Capacity ........................ 3.5 U.S. Gallons (13.25 Liters)

Oil Capacity ................................20 Ounces (0.6 Liters)

*Generator certified in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-14, Motors and Generators

and PGMA (Portable Generator Manufacturers’ Association) standard ANSI/PGMA G300-2018, Safety and Performance of Portable

Generators.

**Per Briggs & Stratton 628K.

Troubleshooting

Wiring Diagram

20 BRIGGSandSTRATTON.COM

Warranty

ABOUT YOUR WARRANTY

Warranty service is available only through Briggs & Stratton Authorized Service Dealers. Most warranty repairs are handled routinely, but sometimes requests for

warranty service may not be appropriate. This warranty covers only defects in materials or workmanship. It does not cover damage caused by improper use or

abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the

Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial

number on the product has been removed or the product has been altered or modified in any way, or if the product has evidence of abuse such as impact damage

or water/chemical corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and

serviced or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by

warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when

normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as filters, belts, cutting blades, and brake pads (except engine

brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specified in the Operator’s Manual. Engine

or equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.

Other Exclusions - This warranty excludes damage due to accident, abuse, modifications, alterations, improper servicing, freezing or chemical deterioration.

Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for

primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or

demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.

WARRANTY PERIOD



** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a

major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods

fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, find the nearest Authorized Service Dealer in our dealer

locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton

Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the first retail or commercial consumer. “Consumer use” means personal residential household use by a

retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced

commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the

product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is

effective for and is subject to the time periods and conditions stated below. For warranty service, find the nearest Authorized Service Dealer in our dealer locator

map at www.briggsandstratton.com. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service

Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to the

warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion is

permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and

you may also have other rights which vary from state to state or country to country.**

Consumer Use Commercial Use

36 months  12 months

BRIGGS & STRATTON PRODUCTS WARRANTY POLICY

80088366EN (Rev. A)

La page charge ...