Deltaco DVR Manuel utilisateur

Digital Video Recorder

4CH DVR

Index

Introduction to Digital Video Recorder------------------2

Front panel buttons-----

--------------------------------------3

Rear panel buttons ------------------------------------------4

DVR installation:video output connection--------------5

DVR installation:video input connection----------------5

DVR installation:sensor installation----------------------6

DVR installation:alarm installation---

---------------------7

Power up the unit --------------------------------------------8

On-screen display--------------------------------------------9

Operation guide:Main menu-------------------------------10

Operation guide:Camera select------------

---------------10

Operation guide:Record select------------

----------------11

Operation guide:Record mode----------------------------11

Operation guide:Record frame-rate-----------

-----------12

Operation guide:Video quality-----------------------------13

Operation guide:Record schedule---------------

---------14

Operation guide:Sub menu-password change--------15

Operation guide:Sub menu-time set---------------------16

Operation guide:Sub menu-display format-------------16

Operation guide:Sequential time--------------------------17

Operation guide:HDD setup -------------------------------17

Operation guide:Sensor setup ----------------------------18

Operation guide: How to start Motion detection

recording------------------------------------------------------19

Operation guide:Playback -------

---------------------------20

Optional functions:Backup via USB port-----------21

Optional functions:Networking setup--------------------22

Optional functions:Audio recording setup--------------23

Appendix I Regulatory --------------------------------------24

Appendix II PC viewer application-----------------------25

Appendix III PC client application------------------------27

Introduction

Introduction to Digital Video Recorder (DVR)

The digital video recorder (DVR) is for recording/retrieving video streams

from up to 4 channels at the same time. It adopts a digital image

compression technology to compress the input channel video streams,

and uses HDD to record the compressed video stream.

The following operation guide explains how to operate/manage the DVR,

and the following installation guide explains how to install DVR at your

home or HDD into the DVR.

Hope you enjoy it, use it to protect your home, and eventually make your

home as SAFE HOME.

2

3

4

11

8

9

10

15

14

13

12

2

1

5

6

7

Front Panel

1. (Menu) button: press to display Operation menu option

2. z(Recording button): press to start recording.

3.  (Stop recording/playback button):press stop recording/playback

(the authorized password is requested upon stopping record;

the default password is 111111)

4. (Fast forward button): press to play the recorded stream faster.

5. f (Playback button): press to start playback

6. (Pause button): press to pause the video playback

7. Reverse:press to playback backward

8. Channel 1 button: press to select channel 1

9. Channel 2 button: press to select channel 2

10. Channel 3 button: press to select channel 3

11. Channel 4 button: press to select channel 4

12. 田 All channels button: press to select all channels display

13,14.  up down buttons: press to change menu field

15.  (Select) button: press to change the setting value or enter into a

sub menu

3

Rear Panel

12

4

3

6

7

911

5

10

8

12

13

1. S Video

2. Video output

3. Monitor : Second Video output

4. Video input

5. Video loop-through

6. Sensor input/alarm output: 4 sensor inputs and one alarm output

7. NTSC/PAL switch

8. DC-in (12Voltage)

9. Audio-in/out

(optional function)

10. LAN(RJ45) (optional function)

11. Power switch

12. PC Link : USB device interface (2.0)

(optional function)

13. VGA output (optional function)

4

DVR Installation

1.Video output connection ( TV or monitor, LCD monitor)

Please connect TV(monitor) or LCD monitor (optional) to the unit over the Video output

connector.

The unit provides 1 x S-Video input, 2 x BNC connector and 1 x VGA output.

(optional)

The above Figure shows the video signal line connection.

BNC connection

S-Video connection

Or through

BNC connection

Or through

AC/DC adaptor

power outlet

Camera

Signal Line

Power line

S-Video connection

2. Video input connection ( Camera)

Please connect Camera to the unit over the Video input connector.

The unit provides 4 x BNC connectors.The camera installation

Procedures are as following:

i. Connect the video signal line: connect the video signal line to the unit

ii.Connect camera power line: Connect camera’s adaptor to camera, and

plug in the adaptor. The complete connection with a camera will be shown

as figure above:

(Optional)

5

DVR Installation

power outlet

AC/DC adaptor

Sensor

Power line

Signal Line

3.Sensor Installation

The unit provides 4 sensor input for 4 channels. The sensor

Installation procedures are as follows. There are two simple steps

For the installation of the sensors.

i. Connect the sensor signal line: Connect the video signal line to the unit. The

Sensor signal terminal is at the unit’s back panel

ii.Connect the sensor adaptor jack into the sensor, and plug in the adaptor.

CH1 CH2 CH3 CH4

Alarm out

6

DVR Installation

Signal Line

AlarmAC/DC adaptor

power outlet

4. Alarm installation

The unit provides 1 internal switch for sounding alarm when the sensor is

Activated due to the unwanted entrance of anonymous visitor. The switch

Is open at normal state, but, when the alarm is activated, the switch is closed

So that the alarm gets the power. The circuitry is shown as above figure.

There are two simple steps for the installation of the alarm

i. Prepare the power supply:the alarm needs a power supply, the power supply

comes with the alarm

ii.Connect the alarm power line:the alarm power line is connected to the alarm

switch terminal.

7

Power up the unit

After the unit is properly installed, the unit is ready to record and play. Then

apply power and switch on.

HDD CHECKING

OK

After the unit is powered on, the

unit is checking HDD for several

seconds, the information will be

displayed on the screen as right:

CH1 CH3

CH3 CH4

The unit will enter into real-time

display mode shown as the right

figure:

NOTICE

Turn off and on the DVR!

1.

Make sure the HDD is off

before removing the drive

2.Once you resume the initial

setting, the right information

will be displayed on the screen.

Then turn off the unit and re

-

power on it.

8

On-Screen Display

MAIN MENU

CAMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE 田

RECORD FRAMERATE 30

VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

Press button to open OSD

menu as right

SEARCH TIME

HDD: MASTER

04/03/24 13:24:21-04/03/24 13:44:54

>01 TIME 04/03/24 13:24:21

>02 TIME 04/03/24 13:30:55

>03 TIME 04/03/24 13:40:54

(¿À) MOVE,() CHANGE,(f)PLAY

1. Power on the system

CH1 CH3

CH3 CH4

● CH1 ● CH3

● CH3 ● CH4

Press button to exit OSD

menu to real-time display

Pressz button to start

recording

Recording Mode Display

OSD Mode Display

SEARCH MODE

CH1 CH3

CH3 CH4

PLAYBACKMODE

Pressf button to search

time or event to playback

Press button to stop

recording( password is

requested!)

Press  button to exit the menu

Press  button to stop playback

Press f button

to start playing

9

Operation guide

Operation Buttons

 ---

press to display menu option.

ST--- press to change menu field or

change the unit’s configuration values.

 --- press to select menu item or

confirm the selection.

Press to display

menu option shown

as right figure.

MAIN MENU

CAMERA SELECT

¾Please stop recording or playback before you enter into OSD menu.

¾You will be requested to enter password, while stopping recording.

¾

”NETWORK SETUP” is optional function which is only provided with LAN model.

MAIN MENU

¾ CAMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE 田

RECORD FRAMERATE 30

VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

SENSOR SETUP

NETWORK SETUP

MAIN MENU

¾ CAMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE 田

RECORD FRAMERATE 30

VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

SENSOR SETUP

The unit provides 4 camera inputs.

You can use channel buttons on

the front panel to select specified

channel for real-time display.

You can use “” button or channel buttons for different combinations for

channel display.

Example:

1. When you choose (----), all cameras are off

2. When you choose (1234), all cameras are displayed.

3. When you choose (---4), only the fourth channel is displayed.

NOTICE

VIDEO LOSS !

“VIDEO LOSS” signal will be displayed, and the

built-in alarm buzzer will be triggered to sound,

while no video connection or connection failure.

10

Operation guide

NOTICE

Channel Display Control

In each mode(回) mode, you can use the

following buttons to display Full-screen format

of each channel.

Channel 1 button: Full screen

display of channel 1

Channel2 button: Full screen

display of channel 2

Channel 4 button: Full screen

display of channel 4

Channel 3 button: Full screen

display of channel 3

RECORD SELECT

MAIN MENU

CAMERA SELECT 1234

¾RECORD SELECT 1234

RECORD MODE 田

RECORD FRAMERATE 30

VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

Selecting channel on this menu

option is same as “CAMERA

SELECT” options.

Only selected camera will record

real-time events during recording

period

RECORD MODE

MAIN MENU

CAMERA SELECT 1234

RECORD SELECT 1234

¾ RECORD MODE 田

RECORD FRAMERATE 30

VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

The unit provides 4 camera inputs.

You can use channel buttons on

the front panel to select specified

channel for real-time display.

11

Operation guide

There are two kinds of recording

mode : 回(each mode; full screen

mode)&田 (quad screen mode).

when you set to 回mode, you can

view the full-screen display of one

specified channel.

When you set to 田 mode, quad-

screen will be displayed.

Please use ¿À buttons of front

panel to select mode and then

MAIN MENU

CAMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE 田

RECORD FRAMERATE 30

VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

SENSOR SETUP

enter  to confirm the selection

RECORD FRAMRATE

There are 9 different frame rate

settings for operation:

(30fps,15fps,10fps,7fps,5fps,4fps,3

fps,2fps,1fps; But the unit is set

to 30fps in the factory )

Please use ¿À buttons of front

panel to select mode and then

enter  to confirm the selection

NOTICE

RECORDING FRAME RATE

The higher the record frame rate is, the more natural look

will be displayed on the screen on playback mode.

But the lower the record frame rate is, the more you can

save the space on HDD.

12

MAIN MENU

CAMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE 田

¾ RECORD FRAMERATE 30

VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

SENSOR SETUP

Operation guide

VIDEO QUALITY

MAIN MENU

CAMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE 田

RECORD FRAMERATE 30

¾ VIDEO QUALITY HI

RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

SENSOR SETUP

There are 3 different video quality

settings for operation: Normal,

Low, High

Please use ¿À buttons of front

panel to select mode and then

enter  to confirm the selection

NOTICE

DIFFERENT VIDEO QUALITY SETTINGS ON

HDD CAPACITY

The higher the video quality is, the clearer images the unit

plays.

But the lower the video quality is, the more you can save the

space on HDD.

13

Operation guide

RECORD SCHEDULE

MAIN MENU

CAMERA SELECT 1234

RECORD SELECT 1234

RECORD MODE 田

RECORD FRAMERATE 30

VIDEO QUALITY HI

¾RECORD SCHEDULE

SUB MENU

HARD DRIVE SETUP

SENSOR SETUP

Enter into this option to change a

recording schedule during a day

(24-hour period) .

PROGRAMMED RECORD

+ T T T S S T T T T T T T T T +

0 3 6 9 12 15 18 21 24

PRESS (

¿À), THEN ( )

PRESS() TO EXIT

Numbers above indicate the time duration

of 24 hours.

(T) Letter indicates recording.

(S) Letter indicates sensor recording. It

means the unit starts recording as the

attached sensors being triggered during this

period.

(--) Recording is off during this duration.

SETTING EXAMPLE:

0:00 ~ 7:00 SENSOR RECORDING

7:00 ~11:00 RECORDING DISABLED

11:00 ~18:00 RECORDING

18:00 ~24:00 SENSOR RECORDING

+ S S S S S S ----T T T T T T T S S S S S S +

: : : : :

0 6 11 18 24

NOTICE

SENSOR RECORDING INSTALLATION

The unit provides 4 alarm inputs which can be

configured as normal close, normal open, motion

detection +NC and motion detection+NO over

“SENSOR SETUP” menu option. (Please refer to P. 18

for the sensor setup). After the sensor configuration,

please go back to “ RECORD SCHEDULE” menu to

enable sensor recording.

14

Operation guide

SUB MENU

¾PASSWORD CHANGE

TIME SET

DATE DISPLAY FORMAT

SEQUENTIAL TIME

PRESS (¿À), THEN ( )

PRESS() TO EXIT

Enter into this option to change

password, time /date setting, date

format and enable the connection

between the unit and PC over

USB interface.

PASSWORD CHANGE .

You enter into “PASSWORD CHANGE”, a

password change input menu replaces the

“SUB MENU” (The default password is

111111)

When the new password is accepted, the

board will flash the following screen

message:

PASSWORD changed!!!

The message will blink 5 times. Then the

display goes back to SUB MENU.

If the password was not accepted, the unit

will automatically return to SUB MENU.

PASSWORD CHANGE

CURRENT PASSWORD: -------

NEW PASSWORD:-------

PASSWORD CONFIRM:--------

PRESS (

¿À), THEN ( )

PRESS() TO EXIT

NOTICE

FRONT PANEL BUTTONS DEFINITION

means “1” 田 means “5” fmeans“b”

means “2” z means “6” means “C”

means “3”  means “7” means “D”

 means “8” means “E”

means “4”  means “9” means “F”

 means “0”

15

Operation guide

TIME SET

Enter into this option to change

date and hour.

TIME

2004/03/21 03:23:21

PRESS (¿À), THEN ( )

PRESS() TO EXIT

DATE DISPLAY FORMAT

PRESS (¿À), THEN ( )

PRESS() TO EXIT

DATE DISPLAY FORMAT

The unit provides yyyy/mm/dd or

dd/mm/yyyy variant which depends on

the regional preference.

16

Operation guide

HDD SETUP

Use this menu to specify each

channel display dwell time.

Dwell time settings determine

from 1 sec to 9 sec between

displays for 4 channels.

Note: Please press “” to confirm

the setting. Or press”田“button to

disable the setting.

SEQUENTIAL TIME

PRESS (¿À), THEN ( )

PRESS() TO EXIT

OVERWRITE ENABLED:

If you choose “YES”, the unit will

continue recording and

overwrite the recorded data

when HDD’s space is full

If you choose “NO”, the unit will stop

recording while HDD’s space is

full

MASTER HDD SIZE:

It indicates the capacity of the primary

HDD installed in the unit

MASTER HDD USED:

It indicates how percentage of HDD’s

capacity has been occupied.

MASTER HDD FORMAT:

It erases all of the recorded data in

Master HDD

The authorized password is requested

before formatting, after the unit

formatted, the following

information will appear on the

screen “HARD DISK

FORMATTED” .

HARD DRIVE SETUP

OVERWRITE ENABLED YES

MASTER HDD SIZE 40000MB

MASTER HDD USED 0MB 0%

MASTER HDD FORMAT

SLAVE HDD SIZE

PRESS (¿À), THEN ( )

PRESS() TO EXIT

17

Operation guide

SENSOR SETUP

SENSOR RECORD TIME:

Recording duration once sensor

Being triggered.

ALARM OUT TIME:

It controls how long ( in second)

the alarm sounds after being triggered.

MOTION SENSITIVE SETUP

Use this menu to adjust the sensitivity of

each channel.

The first bar shows the current

sensitivity of each channel, then use the

“” to set higher sensitivity or lower

Sensitivity. ( 0 stands for highest

Sensitivity, but 9 is for lowest

sensitivity.) .

SENSOR TRIGGER MODES:

The unit provides 5 different modes for

variant uses:

1.Not installed. 2. Normal open.

3. Normal close. 4. Motion +N-C

5. Motion + N-O

In normal open mode, the cable line

Connected between the sensor and

the unit is cut off by an intruder, the unit

starts recording.

In normal close mode, the cable line

connected between the sensor and the

Unit is cut off by an intruder , the unit

stops recording

SENSOR SETUP

SENSOR RECORD TIME 15

ALARM OUT TIME 20

MOTION SENSITIVE SETUP

CHANNEL-1 TYPE:MOTION + N-C

CHANNEL-2 TYPE:MOTION + N-O

CHANNEL-3 TYPE:NORMAL

CLOSE

CHANNEL-4 TYPE:NOT

INSTALLED

PRESS (¿À), THEN ( )

PRESS() TO EXIT

MOTION SENSITIVE SETUP

2 2 4 2 2 2 2 2 2 2 2 2 2 2 2 2

: : : : : : : : : : : : : : : :

1 4 7 10 13 16

O:MORE 9:LESS(SENSITIVE)

PRESS (¿À), THEN ( )

PRESS() TO EXIT

18

Operation guide

How to operate Motion detection recording

PROGRAMMED RECORD

+ T T T S S T T T T T T T T T +

0 3 6 9 12 15 18 21 24

PRESS (

¿À), THEN ( )

PRESS() TO EXIT

Follow the steps as below to

activate motion-detection

recording.

1.Please go to “SENSOR

SETUP” menu as the left

figure shown.

2. Select out the motion option.

3. After the selection, please

be back to MAIN MENU and

go to “PROGRAMMED

RECORD” to power on the

alarm setting.

Notice: The setting under

“PROGRAMMED RECORD” is

necessary for starting the

operation of motion detection

recording.

SENSOR SETUP

SENSOR RECORD TIME 15

ALARM OUT TIME 20

MOTION SENSITIVE SETUP

CHANNEL-1 TYPE:MOTION + N-C

CHANNEL-2 TYPE:MOTION + N-O

CHANNEL-3 TYPE:NORMAL

CLOSE

CHANNEL-4 TYPE:NOT

INSTALLED

PRESS (¿À), THEN ( )

PRESS() TO EXIT

19

La page est en cours de chargement...

Deltaco DVR Manuel utilisateur

Deltaco DVR Manuel utilisateur

dans d''autres langues

Autres documents