Sengled ZM002 Mode d'emploi

Marque: Sengled

Modèle: ZM002

Taper: Mode d'emploi

Vous trouverez ci-dessous de brèves informations pour Module Zigbee ZM002. Ce module Zigbee est utilisé pour les dispositifs d'éclairage, il suffit de le brancher sur la carte d'alimentation puis d'ajouter l'ampoule LED à un hub Zigbee ou à d'autres hubs tiers. Vous pouvez également vous connecter aux hubs intelligents Sengled en suivant les instructions de l'application pour contrôler l'allumage/l'extinction de l'ampoule LED, le niveau de lumens ou les couleurs.

Sengled Zigbee Module

Model: ZM002

Introduction

Model ZM002 is a zigbee module. The wireless

communication part of the product is based on

ZigBee Compliant Platform ,CustomNodes

EFR32MG13P732F512IM32-C technology, which are

fully integrated System-on-Chips that integrate a 2.4

GHz, IEEE 802.15.4-2003-compliant transceiver,

32-bit ARM® Cortex™-M4 microprocessor, flash and

RAM memory, and peripherals of use to designers of

ZigBee-based systems.

Product Name: Sengled Zigbee Module

Hardware

Version: V3

Software

Version: V18

Device Operating Configurations:

Operating

Mode(s):

2.4 GHz IEEE 802.15.4

Supporting

Mode(s):

IEEE 802.15.4

Test

Modulation: O-QPSK

Frequency

Range:

Mode Tx (MHz) Rx (MHz)

2.4 GHz IEEE

802.15.4

2400 ~ 2483.5

B.HF crystal OSC

A high frequency crystal oscillator (HFXO) with

integrated load capacitors, tunable in small steps,

provides a precise timing refer-

ence for the MCU. Crystal frequencies in the range

from 38 to 40 MHz are supported. An external clock

source such as a TCXO can

also be applied to the HFXO input for improved

accuracy over temperature. C.Power supply circuit

The AC 100-130V power is converted to DC 3.3V and

feeds to the whole zigbee module. The 2.1-3.6 V with

internal 1.8 V regulators DC is used by the EFR32MG13

as the input power .

D.Antenna

The EFR32MG13 family includes devices which support

both single-band and dual-band RF communication

over separate physical RF

interfaces.

The 2.4 GHz antenna interface consists of two pins

(2G4RF_IOP and 2G4RF_ION) that interface directly to

the on-chip BALUN. The

2G4RF_ION pin should be grounded externally.

The sub-GHz antenna interface consists of a differential

transmit interface (pins SUBGRF_OP and

SUBGRF_ON) and a differential re-

ceive interface (pinsSUBGRF_IP and SUBGRF_IN). The

external components and power supply connections for

the antenna interface typical applications are shown in

the RF MatchingNetworks section.

Installation and Operating instructions:

This Zigbee Module used for lighting device, plug it in

the power board, then adding the LED bulb to a

zigbee hub or other third-party hubs,you also can

connect Sengled Smart hubs according to their

instructions in apps to control the LED bulb

on/off ,lumens level or colors.

FCC/ISED Regulatory notices:

Modification statement

Sengled Co., Ltd. has not approved any changes or

modifications to this device by the user. Any changes

or modifications could void the user’s authority to

operate the equipment.

Sengled Co., Ltd. n’approuve aucune modification

apportée à l’appareil par l’utilisateur, quelle qu’en soit

la nature. Tout changement ou modification peuvent

annuler le droit d’utilisation de l’appareil par

l’utilisateur.

Interference statement

This device complies with Part 15 of the FCC Rules

and Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference,

and (2) this device must accept any interference,

including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR

d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux

deux conditions suivantes : (1) l'appareil ne doit pas

produire de brouillage, et (2) l'utilisateur de l'appareil

doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en

compromettre le fonctionnement.

RF exposure

This equipment complies with FCC and ISED

radiation exposure limits set forth for an uncontrolled

environment. The antenna should be installed and

operated with minimum distance of 20 cm between

the radiator and your body. Antenna gain must be

below:

Antenna Gain

Frequency Band FCC ID: 2AGN8-ZM002

Model: ZM002

ZigBee 1dBi

This transmitter must not be co-located or operating

in conjunction with any other antenna or transmitter.

The host end product must include a user manual

that clearly defines operating requirements and

conditions that must be observed to ensure

compliance with current FCC RF exposure

guidelines.

For portable devices, in addition to above, a separate

approval is required to satisfy the SAR requirements

of FCC Part 2.1093.

If the device is used for other equipment that

separate approval is required for all other operating

configurations, including portable configurations with

respect to 2.1093 and different antenna configura-

tions.

Cet appareil est conforme aux limites d'exposition

aux rayonnements de l’ISED pour un environnement

non contrôlé. L'antenne doit être installé de façon à

garder une distance minimale de 20 centimètres

entre la source de rayonnements et votre corps. Gain

de l'antenne doit être ci-dessous:

Gain de l‘antenne

ZigBee:≤1dBi

L'émetteur ne doit pas être colocalisé ni fonctionner

conjointement avec à autre antenne ou autre

émetteur.

FCC Class B digital device notice

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try

to correct the interference by one or more of the

following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment

and receiver.

•

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV

technician for help.

Labelling Requirements for the Host device

The host device shall be properly labelled to identify

the modules within the host device. The certification

label of the module shall be clearly visible at all times

when installed in the host device, otherwise the host

device must be labelled to display the FCC ID and

ISED of the module, preceded by the words

"Contains transmitter module", or the word

"Contains", or similar wording expressing the same

meaning, as follows:

L'appareil hôte doit être étiqueté comme il faut pour

permettre l'identification des modules qui s'y

trouvent. L'étiquette de certification du module

donné doit être posée sur l'appareil hôte à un endroit

bien en vue en tout temps. En l'absence d'étiquette,

l'appareil hôte doit porter une étiquette donnant le

FCC ID et l’ISED du module, précédé des mots «

Contient un module d'émission », du mot « Contient

» ou d'une formulation similaire exprimant le même

sens, comme suit :

CAN ICES-3 (B) / NMB-3 (B)

This Class B digital apparatus complies with

Canadian ICES-003.

Cet appareil numérique de classe B est conforme à la

norme canadienne ICES-003.

Installation Guidance

The final host

module combination may also need to

be evaluated against the FCC Part 15B criteria for

unintentional radiators in order to be properly

authorized for operation as a Part 15 digital device.

The user’s manual or instruction manual for an

intentional or unintentional radiator shall caution the

user that changes or modifications not expressly

approved by the party responsible for compliance

could void the user's authority to operate the

equipment. In cases where the manual is provided only

in a form other than paper, such as on a computer disk

or over the Internet, the information required by this

section may be included in the manual in that

alternative form, provided the user can reasonably be

expected to have the capability to access information

in that form.

To ensure compliance with all non-transmitter

functions the host manufacturer is responsible for

ensuring compliance with the module(s) installed and

fully operational. For example, if a host was previously

authorized as an unintentional radiator under the

Declaration of Conformity procedure without a

transmitter certified module and a module is added, the

host manufacturer is responsible for ensuring that the

after the module is installed and operational the host

continues to be compliant with the Part 15B

unintentional radiator requirements.

Sengled ZM002 Mode d'emploi

Marque: Sengled

Modèle: ZM002

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Sengled ZM002 User guide

Sengled ZM002 Mode d'emploi

Sengled ZM002 Mode d'emploi

dans d''autres langues

Autres documents