Red Mountain Valley 8922643 Le manuel du propriétaire

Marque: Red Mountain Valley

Modèle: 8922643

Taper: Le manuel du propriétaire

Assembly Instructions & User’s Manual

28" Gas Fire Pit

ITEM NO.: 2A-OC148

MODEL NO.: 2A-OC148

Please keep this instruction manual for future reference

WARNING

READ INSTRUCTION MANUAL BEFORE ATTEMPTING TO

ASSEMBLE OR OPERATE THIS PRODUCT .

Adult assembly required .

Keep screws and parts out of reach of children .

(Made in China)

WARNINGS AND CAUTIONS

Read the instructions before use. This appliance must be installed in accordance

with such regulations as are enforced.

WARNING : Improper installation , adjustment , alteration , service or maintenance can

cause injury or property damage . Read the installation , operation and maintenance instructions

thoroughly before installing or servicing this equipment .

WHAT TO DO IF YOU SMELL GAS ?

•Do not try to light the appliance .

•Do not touch any electrical switch ; do not use any phone in the vicinity of this product .

•Immediately call your gas supplier from a neighbor’s phone . Follow the gas supplier’s

instructions .

•If you cannot reach your gas supplier , call the fire department .

Installation and service must be performed by a qualified installer , service agency or gas

supplier .

CAUTION:

Installer: Leave the instruction manual to the

user for future use .

Consumer: Please keep this manual for the

future reference.

WARNING:

If the information in this manual is not

followed exactly , a fire or explosion may

result causing property damage ,

personal injury , or loss of life .

DANGER CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has no

odor .

Using it in an enclosed space can kill you .

Never use this appliance in an enclosed space such as a camper ,

tent , car or home .

DANGER

FIRE OR EXPLOSION HAZARD

If you smell gas :

1. Shut off gas to the appliance .

2. Extinguish any open flame .

3. If odor continues , keep away from the

appliance and immediately call your gas

supplier or fire department .

4. After leaving the area , call your gas

supplier or fire department .

Failure to follow these instructions could

result in fire or explosion , which could cause

property damage , personal injury , or death .

WARNING

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

An LP-cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance .

WARNING

For Outdoor Use Only

Installation and service must be

performed by a qualified installer ,

service agency , or the gas supplier .

•Warnings and Cautions……………………............................2,4-5

•Table of Contents. …………………….......................................3

•Exploded View. ……………………...........................................6

•Tools, Parts and Hardware. …………………….........................7

•Assembly Instructions.……………………..............................8-11

•Installation Instructions …………………….............................12

•Operation.……………………...............................................13-15

•Locating Heater For Use.……………………............................16

•Maintenance and Storage.……………………......................17-18

•Trouble Shooting.……………………........................................19

•Warranty Information.……………………................................ 19

BEFORE ASSEMBLY

• Verify that all parts are included with your heater BEFORE you

begin assembly by checking the Parts and Hardware List. For your

convenience, some parts may be pre-assembled or attached to

heater components.

• If all parts are not included, do not attempt to assemble heater. Call

the toll free number on the cover page for replacement parts.

• Leave hardware installed HALF-TIGHTENED on the heater during

assembly until unit is completely assembled, then finish tightening all

hardware installed.

• Use of protective gloves is recommended.

YOUR OWNER'S MANUAL

• Keep and store this Owner's Manual for future reference - it

contains important instructions and procedures for safety and

maintenance.

REMINDER

TABLE OF CONTENTS

Page 3 of 19

NOTE:PLEASE READ THE FOLLOWING SAFETY RULES

When an appliance is for connection to a fixed piping system, the installation must conform

with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI

Z223.1 • NFPA 54; National Fuel Gas Code; Natural Gas and Propane Installation Code, CSA

B149.1; or Propane Storage and Handling Code, CSA B149.2, as applicable;

This appliance requires 20 lb (9 kg) LP gas supply cylinder.

The burner must be replaced prior to the appliance being put into operation if it is evident

that the burner is damaged. The replacement burner shall be that specified by the

manufacturer.

Installation and repair should be done by a qualified service person. The appliance should be

inspected before use and at least annually by a qualified service person. More frequent

cleaning may be required as necessary. It is imperative that control compartment, burners,

and circulating air passageways of the appliance be kept clean.

Always place the appliance on a firm and level surface.

Do not burn solid fuels in this gas appliance.

Use the appliance outdoors in a well-ventilated space only, not in a building, garage, or any

other enclosed area.

When using the appliance, keep the appliance area clear and at least 50 inches from

combustible materials, gasoline and other flammable liquid and vapors. Certain items or

materials, when stored under the appliance or nearby, will be subjected to radiant heat and

could be seriously damaged.

Inspect the gas connections of appliance prior to each use. Do not operate the unit if there

is gas leak. A qualified service person should inspect the appliance annually.

Alert children and adults to the hazards of high surface temperatures and keep them away

to avoid burns or clothing ignition.

Carefully supervise children and pets when they are near the appliance.

Replace and guard or other protective device removed for servicing.

Do not hang clothing or other flammable materials on or near the appliance.

Do not use the appliance if any part has been under water. Immediately call a qualified

service technician to inspect the appliance and to replace any part of the control system and

any gas control which has been under water.

The LP-gas supply cylinder to be used must be: Constructed and marked in accordance with

the Specifications for LP-gas cylinders of the U.S. Department of Transportation (DOT); or the

Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and

Commission, CAN/CSA-B339, as applicable

The LP-gas supply cylinder to be used must be provided with a listed overfilling prevention

device; and provided with a cylinder connection device compatible with the connection for

the appliance.

Use only a cylinder supply system arranged for vapor withdrawal, and the cylinder must

include a collar to protect the cylinder valve.

WARNINGS AND CAUTIONS

Page 4 of 19

Certification CSA

Rated Heat Input 50000 BTU/HR

Fuel LP

Gas Supply 20lb(9kg)LP gas cylinder

Manifold pressure 11” W.C.

Injector Size(diameter) 2.08mm

Gas Supply Pressure Max. 250PSI ,Min.25PSI

WARNINGS AND CAUTIONS

NOTE : PLEASE READ THE FOLLOWING SAFETY RULES :

Perform a leak test with a soapy solution :

1. To check gas connections .

2. After connecting a new cylinder .

3. Upon re-assembly after disassembly .

This appliance is designed to operate with a standard 20 lb propane cylinder

with Approved Cylinder Connection .

WARNING

This product can expose you to chemicals including lead , which is known to

the State of California to cause cancer , and carbon monoxide , which is known

to the State of California to cause birth defects or other reproductive harm . For

more information , go to :

www.P65Warnings.ca.gov.

SPECIFICATION

Before beginning assembly of product , make sure all parts are present . If any

part is missing or damaged , do not attempt to assemble the product . Contact

customer service for replacement parts .

Page 5 of 19

Please check the contents of the packaging to ensure all parts are included. If

missing parts, please contact customer service.

EXPLODED VIEW

Page 6 of 19

ITEM DESCRIPTION PICTURE QTY.

TABLE

TOP 1

CONTROL PANEL

LEG

WITHOUT MAGNET 3

CYLINDER HOLDER

ASSEMBLY

FRONT

PANEL 1

SIDE PANEL

LEG W/ MAGNET

PROTECTIVE ROD

DOOR

PANEL 1

COVER LID

GLASSROCKS

M5 x 10Bolt

M4x 10Bolt

TOOLS NEEDED: (NOT INCLUDED)

Philips screwdriver

Estimated time for assembly: 30 minutes.

TOOLS AND PRATS

HARDWARE

Page 7 of 19

Choose a good, cleared assembly area and get a friend to help you put your gas fire pit together. Lay

cardboard down to protect gas fire pit table top finish and assembly area.

Step 1

Place the Table Top (A) upside down to the soft,

level surface. Attach Control Panel (B) to the

Table Top (A) with (2) M5 x 10 bolts (AA) as

illustrated.

Insert valve into injection pipe of burner firmly.

(Position A)

Insert the end of electrode wire into valve and

prevent it from falling off. (Position B)

Connect thermocouple to the Valve. (Position C)

Step 2

Attach the Protective Rod (H) to the Table Top

(A) with (2) M5 x 10 bolts (AA) as shown.

ASSEMBLY INSTRUCTIONS

Warning : Do not install the table on a hard, unclean or foreign body surface to

avoid scratches on the table top!

Page 8 of 19

Step 3

Attach the Leg W/Magnet (G) to the Table Top

(A) with (3) M5 x 10 bolts (AA) as shown

Attach the 3 Legs Without Magnet (C) to other

three locations of Table Top (A) with (9) M5 x

10 bolts (AA)

Step 4

Connect Control Panel (B) to the Front Panel (E)

with (1) M5 x 10 bolts (AA)

Connect the Leg W/Magnet (G) and Leg without

Magnet (C) to the Front Panel (E) with (4) M5 x

10 bolts (AA)

Note: Install Leg Without Magnet (C) firstly.

ASSEMBLY INSTRUCTIONS

Page 9 of 19

Step 5

Connect the 2 side Panels (F) to Leg without

Magnet (C) with (8) M5 x 10 bolts (AA)

Step 6

Attach the Door Panel (I) to the Leg without Magnet

Close the Door Panel (I) after assembling.

ASSEMBLY INSTRUCTIONS

Page 10 of 19

Step 7

Connect the Cylinder Holder (D) to the four legs

with (4) M5 x 10 bolts (AA). The side with

cylinder locking bolts must face the door panel.

Note: With the help of a friend, turn the gas fire

pit into upright position after this step finished.

Step 8

Put the Glass Rocks (L) on the burning area of Table Top(A).

Note: Place the Cover Lid (K) onto the Table Top (A) when

not in use.

"WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts

specifically approved with this appliance may result in property damage or personal injury."

ASSEMBLY INSTRUCTIONS

Page 11 of 19

INSTALLATION

Two or more people are helpful for an easier installation.

LOCATION

Your fire pit must be installed on flat, stable surface, away

from any combustible materials or construction.

SET-UP

1. Place fire pit on any level, outdoor, non-combustible surface.

NOTE: Do not place the appliance on grass or dirt . This may

prevent proper safety venting.

2. Pour the glass rocks (max 8.8 LB ) onto the fire pit.

3. Open the door panel (I) and place cylinder in the holder

assembly. (Fig. 9)

4. Turn the cylinder locking bolt clockwise to secure the gas

cylinder. (Fig. 10)

5. Attach regulator to cylinder and turn clockwise by hand. (Fig.

11)

6. Check your fire pit for leaks before use. (Fig. 12)

Leak Testing Valves , Hoses and Regulator

1. Turn all control knob(s) to OFF.

2. Be sure regulator is tightly connected to LP tanks.

3. Completely open LP tank valve by turning hand wheel

counter clockwise . If you hear a rushing sound , turn gas

off immediately . There is a major leak at the connection .

Correct before proceeding .

4. Brush soapy solution onto indicated connections shown

below in A and B.

5. If “ growing “ Bubbles appear , there is a leak . Close LP

tank valve immediately and retighten connections . If

leaks can not be stopped, do not try to repair . Call for

replacement parts . Order new parts by giving the serial

number, model and name of items needed to the

Customer Service Center .

6. Always close LP tank valve after performing tank leak

test by turning hand wheel clockwise.

Note:

1) The cylinder supply system must be arranged for

vapor withdrawal.

2) The cylinder used must include a collar to protect

the cylinder valve

The hose assembly must be replaced prior to the

appliance being put into operation if there is evidence

of excessive abrasion or wear, or if the hose is

damaged .

At least once a year, a complete inspection of the entire

gas path components should be performed . If there is

need to replace parts, proceed to leak test after

reassembly (These procedures should be performed by

a professional technician).

Disconnecting Regulator to the LP Tank

1. Turn control knob of regulator to the OFF position.

2. Turn LP tank OFF by turning hand wheel clockwise to a full stop.

3. Turn the coupling nut counterclockwise to loosen the connector.

Loose by hand only---do not use tools.

4. When disconnected, the regulator should be hung on the hook

attached to the appliance.

Page 12 of 19

WARNING: DO NOT ATTEMPT TO OPERATE THE APPLIANCE UNTIL YOU HAVE READ AND

UNDERSTAND ALL PRECAUTIONS . FAILURE TO DO SO CAN RESULT IN PROPERTY DAMAGE,

SERIOUS INJURY, OR DEATH.

WARNING!!!

•Do not use an open flame to check for leakage.

•Do not smoke during testing.

•Do not test indoors.

•A leak check must be performed whenever the

gas cylinder is replaced.

NOTE:

Use only the pressure regulator supplied with this fire

pit. Replace them with those specified by the

manufacturer only.

Before turning gas supply ON

Your fire pit was designed and approved for

OUTDOOR USE ONLY. DO NOT use it inside a building

or any other enclosed area.

Make sure surrounding areas are free of combustible

materials, gasoline, and other flammable vapors or

liquids.

Ensure that there is no obstruction to air ventilation.

Be sure all gas connections are tight and there are no

leaks.

Be sure the access panel is clear of debris.

Be sure any component removed during assembly or

servicing is replaced and fastened prior to starting.

WARNING

FOR YOUR SAFETY :

If at any time you are unable to

light burner and smell gas, wait 5

minutes to allow gas to dissipate

before attempting to light gas

appliance. If after1 minute, you

are unable to light burner, wait 5

minutes and allow flammable

vapors to dissipate before

attempting to light gas appliance.

WARNING

FOR YOUR SAFETY :

DO NOT touch or move gas

appliance for at least 45

minutes after use.

WARNING

Lighting operations should

comply with Lighting

Instruction section. Improper

lighting operations will cause

serious injury and explosion.

Page 13 of 19

WARNING: DO NOT ATTEMPT TO OPERATE THIS HEATER UNTIL YOU HAVE

READ AND UNDERSTAND ALL PRECAUTIONS. FAILURE TO DO SO CAN RESULT

IN PROPERTY DAMAGE, SERIOUS INJURY, OR DEATH.

Before Lighting

The gas fire pit should be thoroughly inspected before each use, and by a

qualified service person at least annually .

If relighting a hot gas fire pit, always wait at least 5 minutes.

5. When burner is lit, turn the control knob to

desired heat output position between "LOW"

and "HIGH".

6. Press down and turn the control knob

clockwise to "OFF" position to shut down the

appliance . Turn off cylinder gas valve.

Lighting instructions

1. Make sure control knob is in the "OFF"

position.

2. Turn LP cylinder gas valve to fully open

position.

3. Press down control knob and turn it

counter clockwise to "LOW" position.

4. If the burner is not lit, press down the

control knob and turn clockwise to "OFF"

position, repeat from step 3 after 5 minutes.

Flame Characteristic

Normally the burner flame is yellow . If the burner flame

is blue and very small, please check the gas cylinder, as it

may be low gas pressure or empty. If there is enough gas

in the cylinder, please contact customer service to change

the burner of the gas fire pit.

If flames lift away from burner or backfire happens, or

produce thick black smoke, the fire pit should be turned

off immediately . The fire pit should not be operated

again until the unit is serviced and/or repaired by a

qualified service technician.

Page 14 of 19

CAUTION: AVOID INHALING FUMES EMITTED FROM THE GAS APPLIANCE’S FIRST

USE. SMOKE AND ODOR FROM THE BURNING OF OILS USED IN

MANUFACTURING WILL APPEAR. BOTH SMOKE AND ODOR WILL DISSIPATE

AFTER APPROXIMATELY 30 MINUTES. THE GAS APPLIANCE SHOULD NOT

PRODUCE THICK BLACK SMOKE.

Note:

The burner may be noisy when initially turned

on . To eliminate excessive noise from the

burner, turn the control knob to the LOW

position. Then, turn the knob to the level of

heat desired.

Operation pressure checked:

If the flame is very small, this is because the

supply pressure is not enough. Please refill gas

cylinder.

Re-light:

1) Turn the control knob to "OFF " position.

2) Wait five minutes before attempting to

relight appliance

3) Repeat steps beginning with step 3 of the

lighting instruction.

Warning:

Gas appliance will be hot after use. Handle with

extreme care.

Shut down instructions:

1) Push in and turn control knob clockwise to "OFF" position.

2) Turn LP cylinder gas valve clockwise to OFF position when

appliance is not in use.

Page 15 of 19

CAUTION: WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT

ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE, THEY

WILL BE SUBJECT TO RADIANT HEAT AND COULD BE

SERIOUSLY DAMAGED.

This gas fire pit is primarily used for

the heating of outdoor patios, decks,

spas, pools and open working areas .

Always make sure that adequate fresh

air ventilation is provided. Follow the

spacing tolerances shown in Figure 13

at all times .

This gas fire pit must be placed on

level, firm ground .

Never operate in an explosive

atmosphere . Keep away from areas

where gasoline or other flammable

liquids or vapors are stored or used.

Page 16 of 19

CLEANING AND MAINTENANCE:

To enjoy years of outstanding performance

from your gas fire pit, make sure you

perform the following maintenance activities

on a regular basis:

•Keep exterior surfaces clean.

•Use warm soapy water for cleaning. Never use

flammable of corrosive cleaning agents.

WARNING

FORYOUR SAFETY

DO NOT touch or move

gas appliance for at least

45 minutes after use.

Allow all burner elements

to cool before touching.

FOR YOUR SAFETY ;

•While washing your unit, be sure to keep the area around the burner dry at

all times. If the gas control is exposed to water in any way, do NOT try to

use it. It must be replaced.

•Keep the appliance area free and clean from

combustible materials, gasoline and other

flammable vapors and liquids; not obstructing

the flow of combustion and ventilation air;

keeping the ventilation opening(s) of the

cylinder enclosure free and clear from debris .

•The hose assembly must be replaced prior to

the appliance being put into operation if

there is evidence of excessive abrasion or

wear, or if the hose is damaged .

•The replacement hose assembly shall be that

specified by the manufacturer.

•At least once a year, the unit should be inspected for the presence of spiders,

spider webs or other insects .

•Air flow must be unobstructed. Keep controls, burner, and circulating air

passageways clean. Signs of possible blockage include：

Gas fire pit does NOT reach the desired temperature .

Gas fire pit glow is excessively uneven .

Gas fire pit makes popping noises .

•Spiders and insects can nest in burner or orifices. This dangerous condition

can damage gas fire pit and render it unsafe for use. Clean burner holes by

using a heavy-duty pipe cleaner. Compressed air may help clear away smaller

particles.

NOTE:

In a salt-air environment such

as near an ocean corrosion

occurs more quickly than

normal. Frequently check for

corroded areas and repair

them promptly.

NOTE:

Wait until gas appliance is cool

before covering.

Page 17 of 19

•Store the fire pit indoors during the winter if it will be subjected to freezing temperatures.

•Disconnect and remove the cylinder from the appliance before the appliance can be

stored indoors.

STORAGE

•Turn the control knob to "OFF" position.

•Turn LP cylinder to OFF position.

•Allow at least 45 minutes for the fire pit to cool down after use, then disconnect and

remove the cylinder.

•Cylinder must be stored outdoors in a well-ventilated area out of the reach of children.

When the cylinder is disconnected , tightly install the threaded valve plugs , and do not

store it in a building, garage or any other closed area.

•You may store product indoors ONLY if the cylinder is disconnected and removed.

•Keep the fire pit area clear and free from combustible materials, gasoline and other

flammable vapors and liquids .

•If you are not using the fire pit cover it to protect exterior surfaces and to help prevent

build up in air passages .

•Store gas fire pit in an area sheltered from direct contact with inclement weather (such

as rain, sleet, hail, snow, dust and debris).A qualified service person should install and

repair the fire pit and inspect it annually .

•It might be necessary to clean this fire pit frequently. You must keep the control

compartment, burner and circulating air passageways clean.

NOTE:

Wait until gas appliance is cool

before covering.

Page 18 of 19

TROUBLE SHOOTING

PROBLEM

OBSERVED

POSSIBLE CAUSE CORRECTIVE MEASURES

Gas odor Gas leak Check all gas connections

Delayed

ignition

Low gas pressure

Clogged or dirty burner ports

Check gas supply pressure

Clean burner parts –see manual

“CLEANING AND MAINTENANCE” section

Incorrect

burner flame

Incorrect gas supply or pressure

Clogged or dirty burner ports

Check gas supply pressure

Clean burner parts

WARRANTY INFORMATION

The appliance has been manufactured under the highest standards of quality and

workmanship . We warrant to the original consumer / purchaser that all aspects of this

product will be free of defects in material and workmanship for one (1) year from the date of

purchase . A replacement for any defective part will be supplied free of charge for

installation by the consumer . Defects or damage caused by the use of other than genuine

parts are not covered by this warranty . This warranty shall be effective from the date of

purchase as shown in the purchasers receipt .

This warranty is valid for the original consumer / purchaser only and excludes industrial ,

commercial or business use of the product , product damage due to shipment or failure

which results from alteration , product abuse , or product misuse , whether performed by a

contractor , service company , or consumer . We will not be responsible for labor charges

and /or damage incurred in installation , repair or replacement , nor for incidental or

consequential damage .

Page 19 of 19

Assembly Instructions & User’s Manual

Foyer au gaz de 28 po

Numéro d’article. : 2A-OC148

Numéro de modèle : 2A-OC148

Veuillez garder ce mode d’emploi pour référence ultérieure

Avertissement

LISEZ LE MANUEL D’INSTRUCTIONS AVANT D’ ESSAYER D’ASSEMBLER

OU D’UTILISER CE PRODUCT .

Assemblage adulte requis .

Gardez les vis et les pièces hors de la portée des enfants .

(Fabriqué en China)

La page charge ...

Red Mountain Valley 8922643 Le manuel du propriétaire

Marque: Red Mountain Valley

Modèle: 8922643

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Red Mountain Valley 8922643 Owner's manual

Red Mountain Valley 8922643 Le manuel du propriétaire

Red Mountain Valley 8922643 Le manuel du propriétaire

dans d''autres langues

Autres documents