Pleasant Hearth OFG444T Manuel utilisateur

OUTDOOR

PROPANE FIREPIT

MODEL #OFG418TA, OFG900T, OFG901T, OFG444T

Français p. 65

*Propane cylinders

sold separately.

Item may have a

slightly different

appearance

depending on

the model #

purchased.

*

Serial Number

Purchase Date

ATTACH YOUR RECEIPT HERE

130-10-111 Rev. 09/29/2017

Español p. 33

C US

ANS Z21.97-2014

•

CSA 2.41-2014

Outdoor Decorative Gas Appliance

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-877-447-4768, 8:30AM – 4:30PM CST, Monday – Friday, or

e-mail us at [email protected]

INSTALLER: Leave this manual with the consumer.

CONSUMER: Retain this manual for future reference.

WARNING

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY,

AN ELECTRICAL SHOCK OR FIRE MAY RESULT

CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

IMPORTANT INSTRUCTIONS

PLEASE READ THIS MANUAL BEFORE INSTALLING AND USING APPLIANCE

2

TABLE OF CONTENTS

Safety Information .................................................................................................................. 4

Package Contents .................................................................................................................. 7

Preparation ............................................................................................................................11

Assembly Instructions ............................................................................................................................. 12

Operating Instructions .......................................................................................................... 19

Care and Maintenance ......................................................................................................... 25

Warranty ............................................................................................................................... 26

Troubleshooting .................................................................................................................... 27

Replacement Parts List ........................................................................................................ 28

DANGER:

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ame.

3. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your re department.

WARNING:

Do not store or use gasoline or other

ammable vapors or liquids in the

vicinity of this or any other appliance.

An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

WARNING: For Outdoor Use Only.

DANGER

CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which

has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space such

as a camper, tent, car or house.

WARNING: Improper installation, adjustment, alteration,

service or maintenance can cause injury or property damage.

Refer to the owner’s information manual provided with this

appliance. For assistance or additional information consult a

qualied installer, service agency or the gas supplier.

3

ANSI Z21.97-2014 • CSA 2.41-2014

Outdoor decorative gas appliances

March 2014

45

Figure 1

LP-Gas Cylinder Label

(See Clause 4.18.2.)

DANGER

•

FLAMMABLE GAS UNDER PRESSURE.

LEAKING LP-GAS MAY CAUSE A FIRE OR EXPLOSION IF IGNITED

CAUSING SERIOUS BODILY INJURY OR DEATH.

CONTACT LP GAS SUPPLIER FOR REPAIRS, OR DISPOSAL OF THIS

CYLINDER OR UNUSED LP-GAS.

WARNING

• FOR OUTDOOR USE ONLY.*

DO NOT USE OR STORE CYLINDER IN A BUILDING,

GARAGE OR ENCLOSED AREA.

WARNING:

Know the odor of LP-gas. If you hear, see

or smell leaking LP-gas, immediately get

everyone away from the cylinder and call the

Fire Department. Do not aκempt repairs.

CauΩon your LP-gas supplier to:

Be certain cylinder is purged of trapped

air prior to ﬁrst ﬁlling.

Be certain not to over ﬁll the cylinder.

Be certain cylinder requaliﬁcaΩon date is

checked.

LP-gas is heavier than air and may seκle in

low places while dissipaΩng.

Contact with the liquid contents of cylinder

will cause freeze burns to the skin.

Do not allow children to tamper or play with

cylinder.

When not connected for use, keep cylinder

valve turned o�. Self contained appliances

shall be limited to a cylinder of 30 lb

capacity or less.

Do not use, store or transport cylinder where

it would be exposed to high temperatures.

Relief valve may open allowing a large

amount of ﬂammable gas to escape.

When transporΩng, keep cylinder secured in

an upright posiΩon with cylinder valve turned

o�.

WHEN CONNECTING FOR USE:

Consult manufacturer’s instrucΩons

concerning the cylinder connecΩon provided

with your appliance.

Be sure regulator vent is not poinΩng up.

Turn o� all valves on the appliance.

Do not check for gas leaks with a match or

open ﬂame. Apply soapy water at areas

marked “X”. Open cylinder valve. If bubble

appears, close valve and have LP-gas

service person make needed repairs. Also,

check appliance valves and connecΩons to

make sure they do not leak before lighΩng

appliance.

Light appliance(s) following manufacturer’s

instrucΩons.

When appliance is not in use, keep the

cylinder valve closed.

Cylinder

Pressure relief valve

Point of connecΩon

Cylinder valve hand wheel

Liquid level indicator

(opΩonal)

DO NOT REMOVE, DEFACE, OR OBLITERATE THIS LABEL

*EXCEPT AS AUTHORIZED BY ANSI/NFPA 58.

DANGER.

Do not store a spare LP cylinder under or near a barbecue grill, or other heat sources.

NEVER ﬁll an LP cylinder beyond 80% full: a ﬁre causing death or serious injury may occur.

Use only in compliance with applicable codes.

Read and follow manufacturer’s instrucΩons.

LP-GAS CYLINDER LABEL

4

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or

install the product. If you have any questions regarding the product, please call customer

service at 1-877-447-4768 8:30AM – 4:30PM CST, Monday – Friday.

DANGER

• Failure to follow the dangers, warnings and cautions contained in this owner’s manual may

result in serious bodily injury or death, or in a re or an explosion causing damage to property.

WARNING

• Maximum inlet gas supply pressure: 250 psi/ 1750 kPa. Manifold pressure with regulator

provided: 11 inch W.C/ 2.74 kPa.

• This appliance shall be used only outdoors in a well-ventilated space and shall not be used

in a building, garage or any other enclosed area.

• DO NOT use this appliance for cooking

• The installation of this product must conform with local codes or, in absence of local codes,

with either the National Fuel Gas Code, ANSIZ223.1/NFPA 54, or the CAN/CGA-B149.1,

Natural Gas and Propane Installation Code.

• Do not use this appliance if any part has been under water. Immediately call a qualied

service technician to inspect the appliance and to replace any part of the control system

and any gas control that has been under water.

• Do not store a spare or disconnected propane cylinder under or near this appliance.

• Do not operate the propane appliance if there is a gas leak present.

• Never use a ame to check for gas leaks.

• Clearance to combustible materials minimum of 24 inches/60.96cm from the sides of

your propane appliance and minimum of 60 inches/152.4 cm from the top of your

propane appliance. Only place unit on non-combustible surfaces.

• Do not put any other appliance cover or anything ammable on, or beneath the appliance.

• The propane appliance should never be used by children. Young children should be

carefully supervised when they are in the area of the appliance.

• Children and adults should be alerted to the hazards of high surface temperatures

and keep a safe distance to avoid burning or clothing ignition.

• Should re go out while burning, turn the gas valve off. Follow the instructions and wait ve

minutes before attempting to relight.

• Never use wood or any other solid fuel in the appliance. Solid fuels shall not be burned in

this gas re pit.

• Never hang or place clothing or other ammable materials on or near the appliance.

• Never lean over the operating appliance or place hands or ngers on the upper portion of

the operational unit.

• Keep ventilation openings in cylinder enclosure free and clear of debris.

• Do not alter the appliance.

• The conversion or attempted use of natural gas in a propane unit or propane gas in a

natural gas unit is dangerous.

• For use with cylinders marked PROPANE only. DO NOT connect to a remote gas supply.

• Do not use this appliance on vehicles or boats. Always operate the appliance on a

at/level surface.

5

SAFETY INFORMATION

WARNING

• Keep any electrical supply cord and fuel supply hose away from any heated surfaces.

• Keep your appliance free and clear from combustible materials, gasoline and other

ammable vapors and liquids.

• Visually inspect burner for obstructions. Keep tank enclosure free and clear from debris.

• Do not use this appliance unless all parts are in place.

• Any guard or other protective device removed for servicing the appliance must be

replaced prior to operating the appliance.

• The hose assembly must be replaced prior to the appliance being put into operation

if there is evidence of excessive abrasion or wear or if the hose is damaged. The

replacement hose assembly shall be specied by the manufacturer.

• Installation and repair should be done by a qualied service person. The appliance

should be inspected before use and at least annually by a qualied service person.

More frequent cleaning may be required as necessary. It is imperative that control

compartment, burners and circulating air passageways of the appliance be

kept clean.

• The propane gas supply cylinder to be used must be constructed and marked in

accordance with the Specications for LP Gas Cylinders of the U.S. Department of

Transportation (D.O.T.) or the National Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as

applicable; and provided with a listed overlling prevention device.

• Use only 20-pound cylinders (approximately 18 ¼ inches high and 12 ¼ inches in

diameter) equipped with a cylinder connection device compatible with the connection

for the hose regulator supplied with this appliance. The cylinder must include a collar to

protect the cylinder valve. The gas cylinder should not be dropped or handled roughly!

• Cylinders must be stored outdoors in a well-ventilated area out of the reach of children.

• Disconnect the cylinder when the appliance is not being used.

• Disconnected cylinders must have valve caps tightly installed and must not be stored in

building or any other enclosed area.

• Do not use this appliance under umbrellas, awnings, etc.

• Only use the appliance on stable surfaces.

• Do not operate with a vinyl or PVC cover.

• Allow the unit to cool before placing a vinyl or PVC cover on the unit.

• Do not sit on unit.

• Never use charcoal or lighter uid with the re pit.

• Do not use gasoline, kerosene or alcohol for lighting.

• Never keep a lled LP cylinder in a hot car or car trunk. Heat will cause the gas pressure

to increase, which may open the relief valve and allow gas to escape.

• Do not lean over re pit when lighting. Read instructions before lighting.

• If the ame extinguishes accidentally during ignition or operation, immediately TURN OFF

the cylinder valve and then TURN OFF the control knob.

6

CAUTION

GLASS ROCKS

1. Do not light or use gas unit if glass rocks are wet. Make sure glass rocks are completely dry

before lighting as intense heat could cause the rock to crack.

2. Glass rocks could hit a person’s face or eyes during the initial startup of this unit. Keep away

from the appliance for the rst 20 minutes after lighting.

F

WARNING

FOR PROPANE GAS UNITS

• The gas pressure regulator provided with the propane appliance must be used.

• The replacement pressure regulator must be those specied by the appliance manufacturer.

• Do not attempt to disconnect the gas cylinder or any gas tting while your appliance is in

operation.

• A dented or rusty propane cylinder may be hazardous and should be checked by your gas

supplier prior to use.

• Do not use a propane cylinder with a damaged valve and any other worn out parts.

• Transit and store the empty gas cylinders carefully and properly.

• If you see, smell or hear the hiss of escaping gas from the propane cylinder:

1. Disconnect propane gas cylinder

2. Do not attempt to correct the problem yourself.

3. Get to your gas supplier and/or the re department for help.

SAFETY INFORMATION

CALIFORNIA PROPOSITION 65

Fuels used in liqueed propane gas appliances, and the products of combustion of such fuels,

can expose you to chemicals including benzene, which is known to the state of california to cause

cancer and cause birth defects or other reproductive harm.

For more information go to: www.P65warnings.ca.gov

WARNING

7

PACKAGE CONTENTS FOR OFG418TA

PART DESCRIPTION QTY.

A Knob 1

B Table Lid 1

C Burner Assembly 1

D 1/4 Table 4

E Angle Iron 4

F Post 4

G Side Panel 3

H Chain 1

I Bottom Plate 1

PART DESCRIPTION QTY.

J Propane Tank Strap 1

K Glass Rocks (one pack) 1

L Door Bracket 1

M Door (Right) 1

N Knob 2

O Door (Left) 1

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

8

PART DESCRIPTION QTY.

A Knob 1

B Table Lid 1

C Burner Assembly 1

D 1/4 Table 4

E Angle Iron 4

F Post 4

G Side Panel 3

H Chain 1

I Bottom Plate 1

PART DESCRIPTION QTY.

J Propane Tank Strap 1

K Glass Rocks (one pack) 1

L Door Bracket 1

M Door (Right) 1

N Door Handle 2

O Door (Left) 1

PACKAGE CONTENTS FOR OFG900T

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

9

PACKAGE CONTENTS FOR OFG901T

PART DESCRIPTION QTY.

A Knob 1

B Table Lid 1

C Burner Assembly 1

D 1/4 Table 4

E Angle Iron 4

F Post 4

G Side Panel 3

H Chain 1

I Bottom Plate 1

PART DESCRIPTION QTY.

J Propane Tank Strap 1

K Glass Rocks (one pack) 1

L Door Bracket 1

M Door (Right) 1

N Door Handle 2

O Door (Left) 1

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

10

PACKAGE CONTENTS FOR OFG444T

PART DESCRIPTION QTY.

A Knob 1

B Table Lid 1

C Burner Assembly 1

D 1/4 Table 4

E Angle Iron 4

F Post 4

G Side Panel 3

H Chain 1

I Bottom Plate 1

PART DESCRIPTION QTY.

J Propane Tank Strap 1

K Glass Rocks (one pack) 1

L Door Bracket 1

M Door (Right) 1

N Door Handle 2

O Door (Left) 1

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

11

HARDWARE USED (FOR OFG418TA, OFG900T, OFG901T, OFG444T)

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list and hardware contents above. If any part is missing or damaged, do not

attempt to assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 60 minutes

Tools required for assembly (not included):

Leak Detection Solution.

EE

*Screw

M4 X 6

Qty. 5

CC

Bolt

M6 X 30

Qty. 4

BB

Nut

M6

Qty. 8

AA

Bolt

M6 X 12

Qty. 38

DD

Screw

M5 X 12

Qty. 4

FF

HH

Wrench

Qty. 1

CAUTION

THIS UNIT IS HEAVY. Two people required for safe assembly.

Two people required for safe assembly. Some parts may contain sharp edges. Wear protective

gloves if necessary. Read and follow all safety statements, warnings, assembly instructions and

use and care instructions before attempting to assemble and use.

Phillips

screwdriver

Qty. 1

II

EXTRA CONTENTS (PACKED IN A SEPARATE PLASTIC BAG)

GG

*Screw

M4 X 10

Qty. 1

*Washer

ø4

Qty.5

* OFG418TA uses only three M4 X 6 screws (EE) and three Washers ø4 (GG).

* OFG444T uses only four M4 X 6 screws (EE) and one M4 x 10 screw (FF).

OFG418TA, OFG900T and OFG901T do not use (FF).

12

ASSEMBLY INSTRUCTIONS

1. Attach the knob (N) or door handle (N) to the door (O)

with M4X6 screws (EE) and washers ø4 (GG). Tighten

with screwdriver (II). Repeat procedure to complete the

assembly of the other door (M).

Hardware Used

2. Turn 1/4 table (D) upside down on a soft, at surface

such as a blanket or carpet to ensure that the table

top surface does not scratch. Attach an angle iron (E)

to a 1/4 table (D) with one M6X12 bolt (AA). Repeat

procedure to complete the assembly of the rest of the 1/4

tables. Do not tighten completely at this time.

1a

1b

D

2

C

II

GG

EE

Washer ø4

Screw M4 X 6

Phillips screwdriver

OFG900T

OFG901T

OFG444T

use handles

OFG418TA

uses knobs

AA

DD

Bolt M6 X 12

X 4

Hardware Used

3. Table Top Assembly:

3-1. On soft surface, line up holes in a 1/4 table (D) with

corresponding holes from another 1/4 table (D).

Insert two M6 X 12 bolts (AA) through holes. Finger

tighten with two M6 nuts (BB). Be sure

1

and

2

are

level, and fully tighten. Repeat procedure to complete

the assembly of the rest of 1/4 tables.

II

Phillips screwdriver

AA

BB

Bolt M6 X 12

Nut M6

X 8

Hardware Used

M

O

N

M

N

GG

EE

AA

D

E

OFG900T, OFG901T,

OFG444T

OFG418TA

X 4 X 2

AA

D

3-1

1

2

CC

DD

C

D

BB

AA

1

2

AA BB

13

BB

ASSEMBLY INSTRUCTIONS

4. Attach propane tank strap (J) to bottom plate (I).

5. Post Installation

Attach four posts (F) to the bottom plate (I) with four

M6 X 30 bolts (CC). The tank hole on the bottom

plate (I) should be in the front as pictured. Tighten

with screwdriver (II) and wrench (HH).

4

L

5-1

F

I

HG

Q

CC

Bolt M6 X 30 X 4

HH

Wrench

Hardware Used

II

Phillips screwdriver

II

Phillips screwdriver

AA

Bolt M6 X 12 X 4

3-2. Once the four panels are connected with two bolts

per connection point, use four more M6 x 12 bolts (AA)

to secure the edges at four points around the table.

Tighten the loose bolts from step two completely.

Hardware Used

5

J

I

CC

F

3-2

AA

14

8. Door (M,O) installation

8-1. Insert the bottom peg of door (left) (O) to the

corresponding hole of the bottom plate (I) as

illustrated in gure 8-1. Slightly lift the door bracket

(L) and insert the top peg of the door (left) (O) to the

corresponding hole of the door bracket (L).

8-1

ASSEMBLY INSTRUCTIONS

6. Hang the chain (H) from the posts (F) as illustrated

in gure 6 so that it connects from corner to corner.

When the re table is fully assembled, the tank will

be placed in the tank hole on the bottom plate (I).

Make sure that the chain is positioned so that it will

not block the tank.

4

L

Q

6

8-2 Repeat above procedure to complete the

assembly of door (right) (M).

Adjust the distance between the doors (M, O) and

the door bracket (L). Adjust the distance between

the doors (M, O) and the bottom plate (I). These

adjustments ensure both doors can open easily.

Tighten the door bracket (L) with screwdriver (II).

8-2

F

H

O

F

Hardware Used

7. Attach the door bracket (L) to the two front posts (F)

with two M6X12 bolts (AA). Do not tighten the bolts yet.

6

E

AA

Bolt M6 X 12 X 2

II

Phillips screwdriver

DD

7

AA

F

L

I

M

TOP PEG

BOTTOM PEG

I

15

10

ASSEMBLY INSTRUCTIONS

AA

Bolt M6 X 12 X 8

10-1

AA

10-2

Hardware Used

9. Side panel (G) Installation.

9-1. Attach three side panels (G) to the posts (F)

with twelve M6 X 12 bolts (AA).

Tighten with screwdriver (II).

10. Table Installation

10-1. Line up holes in assembled table with

corresponding screw holes in base assembly.

Insert eight M6 X 12 bolts (AA) through the

holes. Tighten with wrench (HH).

DD

9-1

9-2

AA

Bolt M6 X 12

X 12

Hardware Used

9-2. After installation the base assembly will look

like gure 9-2.

10-2. After assembly, the assembled unit will look like

gure 10-2.

G

F

AA

II

Phillips screwdriver

HH

Wrench

16

ASSEMBLY INSTRUCTIONS

Hardware Used

11. Burner Assembly Installation

11-1. Make sure the control knob faces the front side

of the unit where the doors are located. Line up

holes in the burner assembly (C) with screw

holes on the table. Insert four M5X12 screws

(DD) through the holes. Fasten with

screwdriver (II).

11-2. The assembled unit will look like gure 11-2.

11-2

11-1

DD

Screw M5 X 12 X 4

II

Phillips screwdriver

DD

C

12. Pour one pack of the glass rocks (K) over the

burner. Do not cover ignition screen with glass

rocks (K). Use a glove when handling glass rocks.

12

A

P

The burner of the rebowl must be covered by glass rocks

completely. Otherwise the ame may be extinguished occasionally.

See the Figure CORRECT and INCORRECT for reference.

CORRECT

INCORRECT

WARNING

DO NOT COVER THE IGNITION SCREEN when

placing the glass rocks into the re bowl. Always

keep Ignition Screen visible. This screen must be

clear and free of obstructions at all times to insure

proper operation.

Screen

Do not place glass

rocks on screen.

Keep screen clear.

K

P

CAUTION

GLASS ROCKS - Use a glove when handling glass rocks.

1. Do not light or use gas unit if glass rocks are wet. Make sure glass rocks are completely dry before lighting as intense heat

could cause the rock to crack.

2. Glass rocks could hit a person’s face or eyes during the initial startup of this unit. Keep away from the appliance for the rst

20 minutes after lighting.

17

ASSEMBLY INSTRUCTIONS

Caution: Never place a table lid on the

re pit when in use. Ensure the re pit

has cooled before placing a table lid over

the re pit.

13. Screw the knob (A) on the table lid (B) with one

M4X6 screw (EE) or one M4X10 screw (FF) and

one washer ø4 (GG). Tighten with phillips

screwdriver (II).

15. Use only 20-pound cylinders (approximately

18 ¼ inches high and 12 ¼ inches in diameter)

equipped with a cylinder connection device

compatible with the connection for the hose

regulator supplied with this appliance. Propane

gas and cylinder are sold separately.

A dented, rusted or damaged propane cylinder

may be hazardous and should be checked by your

cylinder supplier. Never use a propane cylinder

with a damaged valve connection.

15

Standard 20 lb. tank

Use a glove when handling glass rocks.

Do not sit or stand on this table.

Keep children away during assembly. This item contains small parts which can

be swallowed by children.

Do not use indoors and inside any enclosure.

Retain the assembly instruction for future reference.

Installer — Please leave these instructions with the owner.

14. Place the table lid (B) over the re pit.

Total re pit installation is complete.

14

10-2

13

GG

EE

B

A

Hardware Used

FF

GG

EE

Screw M4 X 10

Washer ø4

Screw M4 X 6

X 1 (OFG444T)

X 1 (OFG418TA, OFG900T, OFG901T)

X 1

ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE. INTENDED FOR

RESIDENTIAL USE ONLY.

II

Phillips screwdriver

18

The propane cylinder must be constructed and marked in accordance with the specications for LP

gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres

and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.

The cylinder must have a listed overlling prevention device.

The cylinder must have a connection device compatible with the connection for the appliance.

Never connect an unregulated propane cylinder to this appliance.

The cylinder must include a collar to protect the cylinder valve. The gas cylinder should not be

dropped or handled roughly.

The LP-gas supply cylinder must be disconnected when this appliance is not in use. Storage of

an appliance indoors is permissible ONLY if the cylinder is disconnected and removed from the

appliance. Cylinders must be stored outdoors out of the reach of children and must not be stored in a

building, garage or any other enclosed area. Your cylinder must never be stored where temperatures

can reach over 125°F / 51.5°C.

The maximum inlet gas supply pressure: 250 psi /1750 kPa. The minimum inlet gas supply pressure:

5 psi /35kPa.

Place a dust cap on cylinder valve outlet whenever the cylinder is not in use. Only install the type of

dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or

plugs may result in leakage of propane.

DO NOT obstruct the ow of combustion air and ventilation air to the re pit.

The propane cylinder must be arranged for vapor withdrawal and equipped with a listed overlling

prevention device. Please use the proper cylinder orientation to provide vapor withdrawal.

NOTE: The cylinder must be fully upright for the cylinder to have vapor withdrawal only.

ASSEMBLY INSTRUCTIONS

CAUTION

a. Do not store a spare LP-gas cylinder under or near this appliance.

b. Never ll the cylinder beyond 80 percent full.

c. If the information in (a) and (b) is not followed exactly, a re causing death or serious injury

may occur.

The pressure regulator and hose assembly supplied with the appliance must be used. The installation

must conform with local codes, or in the absence of local codes, with national fuel gas code, ANSI

A223.1/NFPA54, natural gas and propane Installation Code, CSA B149.1, or propane storage and

handling code, B149.2.

CORRECT

WRONG

CORRECT WRONG WRONG

19

ASSEMBLY INSTRUCTIONS

16. Seat and position propane cylinder in the

bottom plate (I).

16

17. Before connection, be sure that there is no debris

caught in the outlet of the gas cylinder, inlet of the

regulator valve or in the outlet of the burner and burner

ports. Ensure the propane cylinder valve is turned off.

Fasten cylinder with propane tank strap (J). Then

connect the regulator (R) to the cylinder as shown in

gure 17.

17

J

R

I

Before connection, be sure that there is no debris caught in the outlet of the gas cylinder, inlet of the

regulator valve or in the outlet of the burner and burner ports. Keep the propane cylinder valve closed

and disconnect the propane cylinder from the regulator valve when the re pit is not in use.

OPERATION INSTRUCTIONS

20

OPERATION INSTRUCTIONS

ARNING

WARNING

In the connection process, make sure:

• the regulator inlet connector mates with the cylinder valve outlet properly, safely and rmly, and;

• the LP gas hose does not come in contact or remain in contact with the burner assembly.

CHECKING FOR LEAKS

After all connections are made, check all connections and ttings on the LP gas tank valve,

gas hose and regulator for leaks with a water and soap solution.

To prevent re or explosion while testing for a leak:

• Always perform a leak test prior to lighting the re pit.

• Do not smoke while testing for a leak.

• Always perform leak tests outdoors in a well-ventilated area.

• Do not use any source of ame while testing for leaks.

• Do not use the re pit until any and all leaks are corrected.

• If you are unable to correct a leak, disconnect the propane supply and call a gas

appliance service dealer.

CONNECTING THE LP TANK

1. The knob on the LP tank must be closed. Make sure that the knob is turned clockwise

to a full stop. The cylinder supply system must be arranged for vapor withdrawal.

2. Check that the control knob on the control unit is turned off.

3. Remove the protective cap from the LP tank valve and coupling nut.

4. Hold the regulator in one hand and insert the nipple into the valve outlet.

Be sure the nipple is centered in the valve outlet. The coupling nut

connects to the large outside threads on the valve outlet. Use care –

do not cross thread the connection.

5. Hand-tighten the coupling nut clockwise until it comes to a full

stop. Firmly tighten by hand only. Do not use tools.

To Disconnect: Fully close the tank valve by turning clockwise.

Turn the coupling nut counterclockwise until the regulator

assembly detaches.

WARNING

ALL INSTRUCTIONS AND SAFEGUARDS ON THIS PAGE MUST BE FOLLOWED TO

PREVENT FIRE, DAMAGE AND/OR INJURY.

La page charge ...

Pleasant Hearth OFG444T Manuel utilisateur

Pleasant Hearth OFG444T Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents