Pioneer X-CM66D Mode d'emploi

Taper
Mode d'emploi
X-CM66D
CD Receiver System
Micro chaîne CD
Sistema receptor de CD
Sistema CD con amplificatore
CD-Receiversystem
CD Receiver System
Operating Instructions
Mode d’emploi
Manual de instrucciones
Istruzioni per l’uso
Bedienungsanleitung
Handleiding
Register your product on/ Enregistrez votre produit sur / Registre su producto en
Registrare il proprio prodotto su / Registrieren Sie hier Ihr Produkt /
Registreer uw product op
http://www.pioneer.eu
(Europe / Europe / Europa / Europa / Europa / Europa)
SN29402598_X-CM66D_En.book 1 ページ 2016年8月2日 火曜日 午後4時8分
2
En
Thank you for buying this Pioneer product.
Please read through these operating instructions so that you will know how to operate your model properly. After you
have finished reading the instructions, put them in a safe place for future reference.
Contents
01 Before you start
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Loading the batteries in the remote control . . . . . . . . . . . .3
Using the remote control . . . . . . . . . . . . . . . . . . . . . . . 3
02 Part names and functions
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Attaching the Non-skid pads . . . . . . . . . . . . . . . . . . . . 6
Speaker system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Attaching the Non-skid pads . . . . . . . . . . . . . . . . . . . . 7
03 Connections
Speaker connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Connecting antennas . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Using external antennas . . . . . . . . . . . . . . . . . . . . . . . 9
Connect the Ethernet cable . . . . . . . . . . . . . . . . . . . . . . . .9
Plugging in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
04 Getting started
To turn the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Setting the clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connecting to the network via Wi-Fi . . . . . . . . . . . . . . . .11
Manual Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Input function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Display brightness control . . . . . . . . . . . . . . . . . . . . . 12
Volume auto set-in. . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Volume control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Sound controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Equalizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
P.BASS control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
BASS/TREBLE control. . . . . . . . . . . . . . . . . . . . . . . . 13
Setting the wake-up timer . . . . . . . . . . . . . . . . . . . . . . . .13
Calling the wake-up timer . . . . . . . . . . . . . . . . . . . . . 14
Cancelling the wake-up timer. . . . . . . . . . . . . . . . . . . 14
Using the wake-up timer . . . . . . . . . . . . . . . . . . . . . . 14
Using the sleep timer . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
05 Disc playback
Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Load the disc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Play tracks on a CD . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Play MP3 music files . . . . . . . . . . . . . . . . . . . . . . . . . 15
Advanced CD or MP3 disc playback . . . . . . . . . . . . . . . .16
Repeat play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Programmed play (CD) . . . . . . . . . . . . . . . . . . . . . . . 17
About downloading MP3 . . . . . . . . . . . . . . . . . . . . . . 17
Switch the display contents . . . . . . . . . . . . . . . . . . . . 17
06 Using network functions
TuneIn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Registering to Favorites. . . . . . . . . . . . . . . . . . . . . . . 18
Registering from a TuneIn Radio account . . . . . . . . . 18
Playing music with Spotify . . . . . . . . . . . . . . . . . . . . . . . .18
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Network Standby setting . . . . . . . . . . . . . . . . . . . . . . . . .19
07 USB playback
Playing USB storage devices . . . . . . . . . . . . . . . . . . . . . 20
Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Random play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Switch the display contents. . . . . . . . . . . . . . . . . . . . . 20
08 Using the tuner
Listening to FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Saving station presets. . . . . . . . . . . . . . . . . . . . . . . . . 21
Using the Radio Data System (RDS)
(for European models only) . . . . . . . . . . . . . . . . . . . . 22
Listening to the DAB+ . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
About DAB+ (Digital Audio Broadcasting) . . . . . . . . . 24
Tuning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Changing the information display . . . . . . . . . . . . . . . . 25
Memorising a station. . . . . . . . . . . . . . . . . . . . . . . . . . 25
DAB Frequency table (BAND III) . . . . . . . . . . . . . . . . 25
09 Other connections
Connecting auxiliary components . . . . . . . . . . . . . . . . . . 26
10 Bluetooth
®
Audio playback
Music playback using Bluetooth wireless technology . . . 27
Remote control operation . . . . . . . . . . . . . . . . . . . . . . . . 27
Pairing with the unit (Initial registration) . . . . . . . . . . . . . 27
Listen to music on the unit
from a Bluetooth capable device
. . . . . . . . . . . . . . . . . . . . 28
Starting by Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Pairing and connection using NFC . . . . . . . . . . . . . . . . . 29
Radio wave caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Scope of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Radio wave reflections . . . . . . . . . . . . . . . . . . . . . . . . 30
Precautions regarding connections
to products supported by this unit
. . . . . . . . . . . . . . . . . 30
11 Additional information
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Playable discs and formats . . . . . . . . . . . . . . . . . . . . . . . 35
Regarding copy protected CDs. . . . . . . . . . . . . . . . . . 35
Supported audio file formats. . . . . . . . . . . . . . . . . . . . 35
Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
When moving this unit. . . . . . . . . . . . . . . . . . . . . . . . . 35
Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Do not place objects on this unit. . . . . . . . . . . . . . . . . 35
About condensation . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the product. . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Handling discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Storing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Cleaning discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
About specially shaped discs . . . . . . . . . . . . . . . . . . . 36
Auto power off setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Advanced network settings . . . . . . . . . . . . . . . . . . . . . . . 37
Checking network information . . . . . . . . . . . . . . . . . . 37
Switching Wi-Fi on and off . . . . . . . . . . . . . . . . . . . . . 37
Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Checking the current software version . . . . . . . . . . . . 37
Updating the software . . . . . . . . . . . . . . . . . . . . . . . . 37
Restoring all the settings to the defaults . . . . . . . . . . . . . 37
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SN29402598_X-CM66D_En.book 2 ページ 2016年8月2日 火曜日 午後4時8分
Before you start 01
3
En
English
Français Español
Chapter 1:
Before you start
What’s in the box
Please confirm that the following accessories are in the box
when you open it.
Remote Control
AAA batteries (R03) x 2
Power cord
Speaker wire x 2
DAB/FM wire antenna
Non-skid pads x 12
Warranty card
Loading the batteries in the remote
control
1 Open the rear lid and load the batteries as
illustrated below.
2 Close the rear lid.
CAUTION
Do not use any batteries other than the ones specified.
Also, do not use a new battery together with an old one.
When inserting the batteries, make sure not to damage
the springs on the battery’s - terminals. This can
cause batteries to leak or over heat.
When loading the batteries into the remote control, set
them in the proper direction, as indicated by the polarity
marks (+ and -).
Do not heat batteries, disassemble them, or throw them
into flames or water.
Batteries may have different voltages, even if they are
the same size and shape. Do not use different types of
batteries together.
To prevent leakage of battery fluid, remove the
batteries if you do not plan to use the remote control for
a long period of time (1 month or more). If the fluid
should leak, wipe it carefully off the inside of the case,
then insert new batteries. If a battery should leak and
the fluid should get on your skin, flush it off with large
quantities of water.
When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
WARNING
Do not use or store batteries in direct sunlight or other
excessively hot place, such as inside a car or near a
heater. This can cause batteries to leak, overheat,
explode or catch fire. It can also reduce the life or
performance of batteries.
Using the remote control
The remote has a range of about 7 m at an angle of about
30º from the remote sensor.
Keep in mind the following when using the remote control:
Make sure that there are no obstacles between the
remote and the remote sensor on the unit.
Remote operation may become unreliable if strong
sunlight or fluorescent light is shining on the unit’s
remote sensor.
Remote controllers for different devices can interfere
with each other. Avoid using remotes for other
equipment located close to this unit.
Replace the batteries when you notice a fall off in the
operating range of the remote.
30°
7 m
30°
SN29402598_X-CM66D_En.book 3 ページ 2016年8月2日 火曜日 午後4時8分
Part names and functions02
4
En
Chapter 2:
Part names and functions
Remote control
1 Í
Switches the receiver between standby and on (page 11).
2 Input function buttons
Use to select the input source to this receiver (page 12).
Use to set up or play the audio file using the Bluetooth
network (page 27).
3MENU
Use to access the menu.
4
/
/
/
, ENTER
Use to select/switch system settings and modes, and to
confirm actions.
5 PGM/MEMORY
Use to memory or program the CD (page 17).
Use to store FM (page 21) or DAB (page 25) stations
in memory.
6 Playback control buttons
Use to control each function after you have selected it using
the input function buttons (page 16).
TUNE +/–
Use to find radio frequencies (page 21).
PRESET +/
Use to select preset radio stations (page 21).
7 Sound control buttons
Adjust the sound quality (page 13).
8SLEEP
See Using the sleep timer on page 14.
9TIMER
Use for setting the clock, as well as for setting and checking
the timers (page 11).
10
Press to change the repeat play setting from a CD (page 16)
or USB (page 20).
11 RANDOM
Press to randomize order play setting from a CD (page 16)
or USB (page 20).
12 DISPLAY
Press to change the display for MP3 (page 17), RDS
(page 22) or DAB (page 25) information.
13
Press to return to the previous display.
1
2
3
6
4
7
8
9
5
11
12
13
14
10
15
16
SN29402598_X-CM66D_En.book 4 ページ 2016年8月2日 火曜日 午後4時8分
Part names and functions 02
5
En
English
Français Español
14 Volume control buttons
Use to set the listening volume (page 12).
15
Mutes/unmutes the sound (page 12).
16 DIMMER
Dims or brightens the display. The brightness can be
controlled in four steps (page 12).
SN29402598_X-CM66D_En.book 5 ページ 2016年8月2日 火曜日 午後4時8分
Part names and functions02
6
En
Front panel
1
Í
STANDBY/ON
Switches the receiver between standby and on (page 11).
2 NFC area
Touching the NFC-equipped smartphone to this area, this
unit can establish Bluetooth connection simply (See
Pairing and connection using NFC on page 29
).
3INPUT
Selects the input source.
4 Remote sensor
Receives the signals from the remote control.
5 TIMER indicator
Lights when the receiver is power off with timer setting.
6 Main display
7 Playback control buttons
Selects the desired track or file to be played back. Use to
stop the playback. Stops playback or resumes playback from
the pause point.
8 Disc tray open/close button
Use to open or close the disc tray (page 15).
9 Volume control
Use to set the listening volume (page 12).
10 Headphone socket
Use to connect headphones. When the headphones are
connected, there is no sound output from the speakers.
11 Disc tray
Place the disc, label side up (page 15).
12 USB terminal
Use to connect your USB mass storage device as an audio
source (page 20).
Attaching the Non-skid pads
Apply the accessory non-skid pads to the bottom surfaces of
this unit.
PHONES
STANDBY/ON
INPUT
1 33 5 8 972 64
10 11 12
The bottom surface
of this unit
SN29402598_X-CM66D_En.book 6 ページ 2016年8月2日 火曜日 午後4時8分
Part names and functions 02
7
En
English
Français Español
Speaker system
1 Tweeter
2 Woofer
3 Bass Reflex Duct
4 Speaker Terminals
Important
Speaker grille cannot be removed.
Both speakers can be used on either the right or the left
side.
Attaching the Non-skid pads
Apply the accessory non-skid pads to the bottom surfaces of
the speakers.
Important
Use the speaker is usually in an upright position.
Take care not to jam your fingers when connecting the
receiver and the speaker and putting them in place.
When placing speakers upright
When placing the speakers vertically upright, attach the non-
skid pads to the bottom surface of the speakers.
When placing speakers horizontally
When placing the speaker horizontally, attach the non-skid
pads to what will be the bottom surface of the speakers.
1
2
4
3
The bottom surface
of the speaker
The bottom surface
of the speaker
when using it
horizontally
SN29402598_X-CM66D_En.book 7 ページ 2016年8月2日 火曜日 午後4時8分
Connections03
8
En
Chapter 3:
Connections
CAUTION
Be sure to turn off the power and unplug the power cord
from the power outlet whenever making or changing
connections.
Connect the power cord after all the connections
between devices have been completed.
Speaker connection
Push open the tabs and insert exposed wire.
The provided speaker wire with red tube is for the (+)
terminal. Connect the wire with red tube the (+)
terminal, and other wire to the (–) terminal.
Both speakers can be used on either the right or the left
side.
CAUTION
These speaker terminals carry HAZARDOUS LIVE
voltage. To prevent the risk of electric shock when
connecting or disconnecting the speaker cables,
disconnect the power cord before touching any
uninsulated parts.
Do not connect any speakers other than those supplied
to this system.
Do not connect the supplied speakers to any amplifier
other than the one supplied with this system.
Connection to any other amplifier may result in
malfunction or fire.
Do not attach these speakers to the wall or ceiling. They
may fall off and cause injury.
Do not install your speakers overhead on the ceiling or
wall. The grill is designed to be detachable, and as such
it may fall and cause damage or personal injury if
installed overhead.
These speakers are magnetically shielded. However,
depending on the installation location, color distortion
may occur if the speaker system is installed extremely
close to the screen of a television set. If this happens,
turn off the television set, and then turn it on after 15 to
30 minutes. If the problem persists, move the speaker
system away from the television set.
Make sure that the speaker cable cores do not become
exposed and make contact with other cable cores. This
may cause malfunction of the product.
Do not allow the speaker cable core to come into
contact with the receiver body.
If the speaker cable core comes into contact with any
metal portion of the receiver’s body, it may damage the
speakers and cause smoke and fire.
Insert speaker cables securely into the terminals and
check that the cable does not come out of easily.
Note
There is no difference between L and R speakers.
Left speakerRight speaker
This unit’s
rear panel
Red tube
Supplied
speaker wire
SN29402598_X-CM66D_En.book 8 ページ 2016年8月2日 火曜日 午後4時8分
Connections 03
9
En
English
Français Español
Connecting antennas
Connect the DAB/FM wire antenna as shown below.
To improve reception and sound quality, connect
external antennas (see Using external antennas).
1 Connect the DAB/FM wire antenna into the
DAB/FM antenna socket.
For best results, extend the DAB/FM antenna fully and fix to
a wall or door frame. Don’t drape loosely or leave coiled up.
Using external antennas
To improve signal reception
Use a PAL connector (not supplied) to connect an external
DAB/FM antenna.
Connect the Ethernet cable
Connect this unit to the network using wired LAN or Wi-Fi
(wireless LAN). You can enjoy features such as TuneIn and
Spotify by connecting to the network. If you connect by
wired LAN, connect with an Ethernet cable to the NETWORK
port as shown in the illustration. To connect by Wi-Fi, refer to
Connecting to the network via Wi-Fi”(page 11).
Use a shielded CAT5 Ethernet cable (straight-type).
One-touch PAL
connector
75 coaxial
cable
SN29402598_X-CM66D_En.book 9 ページ 2016年8月2日 火曜日 午後4時8分
Connections03
10
En
Plugging in
Before making or changing the connections, switch off the
power and disconnect the power cord from the AC outlet.
After you’ve finished making all connections, plug the unit
into an AC outlet.
CAUTION
Do not use any power cord other than the one supplied
with this unit.
Do not use the supplied power cord for any purpose
other than that described above.
To AC outlet
This unit’s rear panel
Power cord
SN29402598_X-CM66D_En.book 10 ページ 2016年8月2日 火曜日 午後4時8分
Getting started 04
11
En
English
Français Español
Chapter 4:
Getting started
To turn the power on
Press the Í to turn the power on.
After use:
Press the Í to enter the power stand-by mode.
Setting the clock
1 Press
Í
to turn the power on.
2 Press TIMER on the remote control.
“CLOCK” is shown on the main display.
3 Press ENTER.
4 Press
/
to set the day, then press
ENTER.
5 Press
/
to set the hour, then press
ENTER.
6 Press
/
to set the minute, then press
ENTER to confirm.
7 Press ENTER.
To confirm the time display:
Press the TIMER. The time display will appear for about 10
seconds.
To readjust the clock:
Perform “Setting the clock” from step 1.
Note
When power supply is restored after unit is plugged in
again or after a power failure, reset the clock.
Connecting to the network via Wi-Fi
You can enjoy features such as TuneIn and Spotify by
connecting to the network.
Adjust the angle of the wireless antenna according to
the connection status.
Do not connect the Ethernet cable.
Manual Setup
Enter the password (key) of the access point to establish
connection.
Take a note of the SSID and password (key) which is on
the main unit of the access point.
1 Press MENU on the remote control.
2 Press
/
to select “Wi-Fi Setting”, and
press ENTER.
3 Press
/
to select “Manual Setup”, then
press ENTER.
4 Press
/
to select the SSID of the access
point to be connected, then press ENTER.
5 Press ENTER.
6 Enter the password.
/:Switch the type of text to enter.
abc...xyzABC...XYZ123...789 !”...|}~
/:Move the position to enter the characters.
7 Press ENTER.
“Connected” is displayed when the connection is established
and lights.
SN29402598_X-CM66D_En.book 11 ページ 2016年8月2日 火曜日 午後4時8分
Getting started04
12
En
Auto Setup
If the access point has an automatic connection button, you
can connect without entering a password.
1 Press MENU on the remote control.
2 Press
/
to select “Wi-Fi Setting”, and
press ENTER.
3 Press
/
to select “Auto Setup”, then
press ENTER.
4 Press the automatic setting button of the
access point to be connected.
“Connected” is displayed when the connection is established
and lights.
General control
Input function
When the INPUT on main unit is pressed, the current
function will change to different mode. Press the INPUT
repeatedly to select desired function.
Display brightness control
Press DIMMER to dims the display brightness. The
brightness can be controlled in four steps.
Volume auto set-in
If you turn off and on the main unit with the volume set to 31
or higher, the volume starts at 30 and sets in to the last set
level.
Volume control
Turn the volume knob towards VOLUME (on main unit) or
press VOL +/– (on remote control) to increase or decrease
the volume.
CAUTION
The sound level at a given volume setting depends on
speaker efficiency, location, and various other factors.
It is advisable to avoid exposure to high volume levels.
Do not turn the volume on to full at switch on. Listen to
music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
Muting
The volume is muted temporarily when pressing the on
the remote control. Press again to restore the volume.
CD
BluetoothTuneIn Spotify
DAB
A
udio In USB FM
SN29402598_X-CM66D_En.book 12 ページ 2016年8月2日 火曜日 午後4時8分
Getting started 04
13
En
English
Français Español
Sound controls
Equalizer
When the EQ is pressed, the current mode setting will be
displayed. To change to a different mode, press the EQ
repeatedly until the desired sound mode appears.
P.BASS control
When the power is first turned on, the unit will enter the
P.bass mode which emphasises the bass frequencies. To
cancel the P.bass mode, press the P.BASS on the remote
control.
BASS/TREBLE control
Press the SOUND to select “BASS” or “TREBLE”, then
press
/
to adjust the bass or treble.
Note
The EQ and P.BASS cannot operate simultaneously.
The most recently selected of these two functions will
be the one used.
SOUND can operate alongside either the EQ or
P.BASS.
When one of the above two functions is selected,
the function that is not selected will be displayed
as follows.
1 When P.BASS setting (ON/OFF) is changed
EQ : FLAT
2 When EQ setting is changed
P.BASS : OFF
Setting the wake-up timer
Used to change the existing timer setting, or to set a new
timer.
1 Press
Í
to turn the power on.
2 Press and hold TIMER on the remote
control.
3 Press
/
to select “ONCE” or “DAILY”,
then press ENTER.
ONCE – Once timer play works for one time only at a
preset time.
DAILY Daily timer play works at the same preset time
and days of week.
4 Press
/
to select “TIMER SET”, then
press ENTER.
5 Press
/
to select the timer playback
source, then press ENTER.
CD, DAB, FM and USB can be selected as the playback
source.
6 Press
/
to select the timer day, then
press ENTER.
7 Press
/
to set the hour, then press
ENTER.
8 Press
/
to set the minute, then press
ENTER.
Set the time to finish as in steps 7 and 8 above.
9 Adjust the volume press VOL +/– , then
press ENTER.
” appears on the display.
10 Press
Í
to enter the power standby mode.
The TIMER indicator lights up.
SN29402598_X-CM66D_En.book 13 ページ 2016年8月2日 火曜日 午後4時8分
Getting started04
14
En
Calling the wake-up timer
It can be used to re-use an existing timer setting.
1 As well as steps 1 through 3 in “Setting the
wake-up timer”.
2 Press
/
to select “TIMER ON”, then
press ENTER.
Cancelling the wake-up timer
It can be used to turn off the timer setting.
1 As well as steps 1 through 3 in “Setting the
wake-up timer”.
2 Press
/
to select “TIMER OFF”, then
press ENTER.
Using the wake-up timer
1 Press
Í
to turn the power off.
2 At the wake-up time, this unit will turn on
automatically and play the selected input
function.
Note
If at the wake-up time the USB storage device is not
connected to this unit or a disc is not inserted, this unit
will be turned to on and not play back the track.
Some discs may not be played automatically at the
wake-up time.
If you set the timer, take one minute or more between
the start and end time.
Using the sleep timer
The sleep timer switches off the unit after a specified time so
you can fall asleep without worrying about it.
1 Press SLEEP repeatedly to select a switch
off time.
Choose between 10 min, 20 min, 30 min, 60 min, 90 min, 120
min, 150 min, 180 min or OFF. The newly set value displays
for 3 seconds, and then the setting is completed.
Note
The sleep timer can be set by pressing SLEEP while
the remaining time is displayed.
Using Headphones
Connect to the jack plug of the headphones.
When the headphones are connected, there is no sound
output from the speakers.
Do not turn the volume on to full at switch on and listen
to music at moderate levels. Excessive sound pressure
from earphones and headphones can cause hearing
loss.
Before plugging in or unplugging the headphone,
reduce the volume.
Be sure your headphone has a 3.5 mm diameter plug
and impedance between 16
and 50 . The
recommended impedance is 32
.
PHONES
STANDBY/ON
INPUT
SN29402598_X-CM66D_En.book 14 ページ 2016年8月2日 火曜日 午後4時8分
Disc playback 05
15
En
English
Français Español
Chapter 5:
Disc playback
This system can play back a standard CD, CD-R/RW in the
CD format and CD-R/RW with MP3 files, but cannot record
on them. Some audio CD-R and CD-RW discs may not be
playable due to the state of the disc or the device that was
used for recording.
For details about MP3, see page 35.
Playing discs or files
Load the disc
1 Press
Í
to turn the power on.
2 Press CD on the remote control or INPUT
repeatedly on the main unit to select CD input.
3 Press
<
on the main unit to open the disc tray.
4 Place the disc on the disc tray, label side up.
5 Press
<
on the main unit to close the disc
tray.
Play tracks on a CD
1 When the recognition is completed, press
1;
.
After the last track is played, the unit will stop automatically.
Play MP3 music files
MP3 track data is called “music fileand the location they are
stored is called a “folder” in this document.
1 When the recognition is completed, press
/
to select the folder where the music file is
stored ([ ]), then press
or ENTER.
Repeat this step if there are other folders inside the
selected folder.
To return to the previous folder, press
or .
2 Press
/
to select the music file ([ ]), and
then press
1;
or ENTER.
Once play starts, only music files inside the same folder
can be played continuously.
CAUTION
Do not place two discs in one disc tray.
Do not play discs of special shapes (heart, octagon,
etc). It may cause malfunctions.
Do not push the disc tray whilst it is moving.
If the power fails whilst the tray is open, wait until the
power is restored.
Be sure to place 8 cm disc in the middle of the disc tray.
Note
Due to the structure of the disc information, it takes
longer to read an MP3 disc than a normal CD
(approximately 20 to 90 seconds).
When the beginning of the first track is reached during
fast reverse, the unit will enter the playback mode (only
for CD).
If TV or radio interference occurs during CD operation,
move the unit away from the TV or radio.
Tip
When no operation has done in CD mode and the audio
file is not played for more than 20 minutes, the power
will automatically turn off. In this case it is required that
the Auto power off is switched to ON.
Auto power off can be switched to ON/OFF (page 37).
e.g.,
SN29402598_X-CM66D_En.book 15 ページ 2016年8月2日 火曜日 午後4時8分
Disc playback05
16
En
Basic operations
Advanced CD or MP3 disc playback
Repeat play
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press repeatedly until “REPEAT ONE” appears. Press
ENTER.
To repeat all tracks:
Press repeatedly until “REPEAT ALL” appears. Press
ENTER.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play (CD)” section
(page 17) and then press repeatedly until “REPEAT
ALL” appears. Press ENTER.
To cancel repeat play:
Press repeatedly until “REPEAT OFF” appears. Press
ENTER.
Note
After performing repeat play, be sure to press .
Otherwise, the disc will play continuously.
During repeat play, random play is not possible.
Random play
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
Press RANDOM repeatedly until “RANDOM ON” appears.
Press ENTER.
To cancel random play:
Press RANDOM repeatedly until “RANDOM OFF” appears.
Press ENTER.
Note
If you press the 9 during random play, you can move
to the track selected next by the random operation.
In random play, the unit will select and play tracks
automatically. (You cannot select the order of the
tracks.)
During random play, repeat play is not possible.
Function Main unit Remote
control
Operation
Play
Press in the stop mode.
Stop
Press in the playback mode.
(when playing a CD)
“RESUME” is displayed
and the place where you
stopped play is
memorized. Press again
and the memorized
position is cleared.
Pause
Press in the playback mode.
Press
1;
to resume
playback from the paused
point.
Track up/
down
Press in the playback or
stop mode.
If you press the button in the
stop mode, press
1;
to
start the desired track.
(when playing MP3)
You can only skip forward
or back to music files
inside the same folder.
Fast
forward/
reverse
Press and hold down in the
playback mode.
Release the button to
resume playback.


 
 
SN29402598_X-CM66D_En.book 16 ページ 2016年8月2日 火曜日 午後4時8分
Disc playback 05
17
En
English
Français Español
Programmed play (CD)
You can choose up to 24 selections for playback in the order
you like.
1 Whilst in the stop mode, press PGM/
MEMORY on the remote control to enter the
programming save mode.
2 Press
:
9
to select the desired tracks.
3 Press ENTER to save track number.
4 Repeat steps 2 - 3 for other tracks. Up to 24
tracks can be programmed.
If you want to check the programmed tracks, press
PGM/MEMORY.
If you make a mistake, the last programmed tracks will
be canceled by pressing .
5 Press
1;
to start playback.
To cancel the programmed play mode:
To cancel the programmed play, press twice on the
remote control. The display will show “PRG CLEAR” and all
the programmed contents will be cleared.
Adding tracks to the program:
Press the PGM/MEMORY. Then follow steps 2 - 3 to add
tracks.
Note
When a disc is ejected, the program is automatically
cancelled.
If you press the Í to enter the standby mode or change
the function from CD to another, the programmed
selections will be cleared.
During the program operation, random play is not
possible.
About downloading MP3
There are many music sites on the internet that you can
download MP3 music files. Follow the instructions from the
website on how to download the music files. You can then
play back these downloaded music files by burning them to
a CD-R/RW disc.
Your downloaded song/files are for personal use only.
Any other usage of the song without owner’s
permission, is against the law.
Switch the display contents
1 Press DISPLAY during playback.
If the title, artist and album name has been written to the file,
that information will be displayed. (You can view this unit is
only alphanumeric characters. Non- alphanumeric character
are displayed in the “ ”.)
Note
“Not supported playback file” can not be playback. In
this case, will be skipped automatically.
There may be cases where no information can be
displayed.
Displaying title, artist, and albums is only supported with
ID3 Version 1 (1.0 or 1.1).
Title display
Number of the track, title
display
Artist display
Album display
Number of the track in
a folder, playback time
display
Number of the track in a
folder, remaining time
display
SN29402598_X-CM66D_En.book 17 ページ 2016年8月2日 火曜日 午後4時8分
Using network functions06
18
En
Chapter 6:
Using network functions
TuneIn
With more than 70,000 radio stations and 2 million on-
demand programs registered, TuneIn Radio is a service
where you can enjoy music, sports and news from all over
the world.
Connect this unit to the network. (page 9, 11)
1 Press
Í
to turn the power on.
2 Press NET on the remote control or
INPUT
repeatedly on the main unit to select TuneIn.
3 Press / to select a folder ([ ]), then
press ENTER.
4 Press / to select a radio station or
program ([ ]), then press ENTER.
Registering to Favorites
You can register the radio station or program being
broadcast in a “Favorites” folder. To play, select the program
from “Favorites”.
To register a program in Favorites
1 Press ENTER while listening to a program.
2 Press
/
to select “Add to My Presets”, then press
ENTER.
To delete a program from Favorites
1 Press ENTER while listening to a program.
2 Press
/
to select “Remove from Presets”, then press
ENTER.
Registering from a TuneIn Radio account
Creating an account on the TuneIn Radio website
(tunein.com) and associating the device from My Page on
the TuneIn Radio website allows you to automatically add
radio stations and programs you have followed on the
website to “Favorites” on the unit.
Use the registration code displayed on this unit to associate
the device.
1 Press
/
to select Settings and press ENTER.
2 While “Registration Code” is being displayed, press
ENTER.
Playing music with Spotify
This unit supports Spotify Connect. To enable Spotify
Connect, install the Spotify application on your smartphone
or tablet and create a Spotify premium account.
This unit needs to be connected to the same router as
the smartphone or tablet.
Refer to the following for Spotify settings:
www.spotify.com/connect/
The Spotify software is subject to third party licenses
found here:
www.spotify.com/connect/third-party-licenses
Playback
1 Connect the smartphone to the network that
this unit is connected to.
2 When the power of this unit is on, click the
Connect icon in the track play screen of the
Spotify app.
3 Select this unit (Pioneer X-CM66).
4 The input selector of this unit
automatically changes to Spotify and
streaming of Spotify starts.
When “Network Standby” (
page 19)
is set to “Net STBY
ON”, by clicking the Connect icon and selecting this
unit, then even if this unit is in standby mode, the power
will come on automatically and streaming starts.
If the volume setting on the Spotify enabled device is
low, the sound will not be output from this unit, so adjust
the volume to an appropriate level.
SN29402598_X-CM66D_En.book 18 ページ 2016年8月2日 火曜日 午後4時8分
Using network functions 06
19
En
English
Français Español
Network Standby setting
You can turn on the power of the unit via the network using
an application that can control this unit.
1 Press MENU on the remote control.
2 Press / until “Network Standby” is
displayed, then press ENTER.
3 Press
/
to switch auto power off setting
ON/OFF.
Initial setting is set to
ON
.
Note
Power consumption in the standby mode increases
when this function is ON.
SN29402598_X-CM66D_En.book 19 ページ 2016年8月2日 火曜日 午後4時8分
USB playback07
20
En
Chapter 7:
USB playback
Playing USB storage devices
It is possible to listen to two-channel audio using the USB
interface with MP3 files on the front of this receiver.
Pioneer does not guarantee that any file recorded on a
USB storage device will play or that power will be supplied
to a USB storage device. Also note that Pioneer will accept
no responsibility whatsoever for loss of files on USB
storage devices caused by connection to this unit.
For details about MP3, see page 35.
1 Press USB as the input source.
“USB” is shown on the main display.
2 Connect the USB storage device.
This receiver does not support a USB hub.
3 When the recognition is completed, press
/
to select the folder where the music file is
stored ([ ]), then press
or ENTER.
MP3 track data is called “music file” and the location
they are stored is called a “folder” in this document.
Repeat this step if there are other folders inside the
selected folder.
To return to the previous folder, press
or .
4 Press
/
to select the music file ([ ]), and
then press
1;
or ENTER.
Once play starts, only music files inside the same folder
can be played continuously.
For details about the basic operations, see page 16.
When changing to a different input source, stop the
USB memory playback first, before changing.
Turn the power off before removing the USB storage device.
Note
This unit may not recognize a USB storage device, play files
or supply power to a USB storage device. For details, see
When a USB storage device is connected
on page 33.
When a USB storage device is not playing and the unit has
not been operated for 20 minutes or more, the power will
automatically turn off. In this case it is required that the
Auto power off is switched to
ON
(page 37).
Repeat play
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press repeatedly until “REPEAT ONE” appears. Press
ENTER.
To repeat all tracks:
Press repeatedly until “REPEAT ALL” appears. Press
ENTER.
To cancel repeat play:
Press repeatedly until “REPEAT OFF” appears. Press
ENTER.
Note
After performing repeat play, be sure to press
. Otherwise,
the file of USB storage device will play continuously.
During repeat play, random play is not possible.
Random play
The file of USB storage device can be played in random
order automatically.
To random play all tracks:
Press RANDOM repeatedly until “RANDOM ON” appears.
Press ENTER.
To cancel random play:
Press RANDOM repeatedly until “RANDOM OFF” appears.
Press ENTER.
Note
If you press the 9 during random play, you can move
to the track selected next by the random operation.
In random play, the unit will select and play tracks
automatically. (You cannot select the order of the tracks.)
During random play, repeat play is not possible.
Switch the display contents
This unit can switch the information recorded in the USB
storage device. For details, see Switch the display contents
on page 17.
USB storage device
(commercially available)
SN29402598_X-CM66D_En.book 20 ページ 2016年8月2日 火曜日 午後4時8分
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229

Pioneer X-CM66D Mode d'emploi

Taper
Mode d'emploi