Kemo Electronic M148A Assembly Instructions

Taper
Assembly Instructions
• LAST
• LOAD
DE
M148A | Batteriewächter 12 V/DC
Dieser Batteriewächter schützt Ihre Auto-
batterie vor Tiefentladung durch das rechtzeitige
Abschalten von Verbrauchern wie Kühlboxen, Hei-
zungen, Radios, Fernsehgeräten usw. Er schaltet au-
tomatisch wieder ein nach Wiederkehr der normalen
Spannung. Die Abschaltspannung ist einstellbar: ca.
10,4 - 13,3 V.
GB
M148A | Battery Guard 12 V/DC
This battery saver protects your car battery
from total discharge by switching off consumers such
as ice boxes, heaters, radios + television sets, etc. in
time. It switches on again automatically after return of
the normal voltage. The interrupting voltage is adjus-
table: approx. 10.4 - 13.3 V.
ES
M148A | Controlador de baterías 12 V/DC
Este protector de acumulador protege su
batería de coche contra descarga total por desconec-
tar a tiempo dispositivos consumidores como cajas
frigorícas, calefacciones, radios + televisores, etc.
Él conecta de nuevo automáticamente cuando la ten-
sión normal regresa. La tensión de desconexión es
ajustable: aprox. 10,4 - 13,3 V.
FR
M148A | Contrôleur de batterie 12 V/DC
Ce contrôleur d’accumulateur protège votre
batterie pour auto contre décharge profonde par dé-
connecter à temps des dissipateurs comme caisses
frigoriques, chauffages, radios + téléviseurs, etc. Il
intercale de nouveau automatiquement quand la ten-
sion normale revient. La tension de rupture est ajus-
table: env. 10,4 - 13,3 V.
NL
M148A | Batterij bewaker 12 V/DC
Deze accusaver beschermt uw auto accu
voor te grote ontlading door middel van het uitscha-
kelen van “zware” apparaten zoals koelboxen, verwar-
ming, radio / tv, etc. Deze schakelt automatisch weer
aan, bij de normale spanning. De uitschakelspanning
is instelbaar: ca. 10.4 - 13.3 V.
PT
M148A | Controlador de bateria 12 V/DC
Este acumulador saver protege a sua bate-
ria do carro contra descarga total através do oprturno
desligar do consumidor como caixas térmicas, aque-
cimentos, rádios e televisores etc. Liga novamen-
te automático depois da volta da tensão normal. A
tensão de circuito de desconexão pode ser ajustada:
ca. 10,4 - 13,3 V.
PL
M148A | Czujnik akumulatora 12 V/DC
Czujnik akumulatora chroni Państwa aku-
mulator przed całkowitym rozładowaniem, odłączając
odpowiednio wcześniej odbiorniki, takie jak przenoś-
na lodówka, ogrzewanie, radio, telewizor itp. Po przy-
wróceniu „normalnego” napięcia czujnik ponownie
włącza odbiorniki. Napięcie odłączające można regu-
lować: ok. 10,4 - 13,3 V.
RU
M148A | Прибор, предотвращающий
полнуюразрядку12Вольтногоаккуулятора
Дaнный модуль прeдотвращает полную рaзрядку
аккумулятора и своевременно отключает от него
потрeбитeли нaпр. холодильники, обогреватели,
рaдиоприeмники, тeлeвизоры и т.д. Обратное
включeние модуля происходит aвтомaтичeски,
если нaпряжeние аккумулятора поднимается до
нормaльного уровня. Нaпряжeниe отключeния:
можно установить примeрно 10,4 - 13,3 Вольт.
DE
Bestimmungsgemäße Verwendung:
Schutz einer Autobatterie gegen Tiefentladung durch angeschlossene Verbraucher in Gartenlau-
ben, Campingzelten, parkenden Campingwagen usw.
Aufbauanweisung:
Das Modul wird so eingebaut, dass es keiner Feuchtigkeit, starken Vibrationen oder großer Hitze
ausgesetzt wird. Die Anschlüsse werden gemäß Zeichnung mit der Batterie und dem Verbraucher
verbunden. Bitte verwenden Sie Kabel mit einem ausreichenden Querschnitt (möglichst >1,5
mm²), damit keine zu hohen Spannungsverluste im Kabel auftreten.
Es ist dringend erforderlich eine Sicherung, gemäß Zeichnung, vorzuschalten!
Achtung: Kurzschlüsse oder Überlastung auf der Verbraucherseite des Moduls können dazu füh-
ren, dass das Modul defekt wird und dann nicht mehr abschaltet! Weil jedes Modul vor dem Ver-
sand sorgfältig auf Funktion geprüft wurde, ist in solchen Fällen und auch bei einer Beschädigung
mit zu hoher Spannung (>15 V) ein Kulanzersatz nicht möglich!
Die Metall-Grundplatte des Moduls kann sich, je nach Belastung, erwärmen. Bei Lastströmen bis
ca. 10 A ist keine zusätzliche Kühlung erforderlich. Das Modul sollte aber „gut belüftet“ eingebaut
werden, damit evtl. auftretende Wärme durch Luftzirkulation von der Metallplatte abgeleitet wird.
Bei höheren Strömen 10 - 20 A muss das Modul mit der Metallplatte plan auf eine andere, grö-
ßere Metallplatte gebaut werden, damit die Wärme abgeleitet wird. Wir empfehlen eine Platte ca.
10 x 15 x 0,5 cm oder etwas Ähnliches mit ähnlicher Kühlwirkung. Die Grundplatte des Moduls
darf sich im Dauerbetrieb nicht über 70°C erwärmen.
Sie können mit dem kleinen Trimmer neben den Steckanschlüssen die Abschaltspannung ein-
stellen. Wenn der Regler ganz zum Anschlag links gedreht ist, schaltet das Modul bei ca. 10,4
V (±0,3 V) ab und am Anschlag rechts bei ca. 13,3 V (±0,3 V) ab. Dazwischen können stufenlos
dazwischen liegende Spannungen eingestellt werden. Wir empfehlen, den Regler auf eine Mit-
telstellung zu bringen. Dann schaltet das Modul bei ca. 11,7 V (±0,3 V) ab und das ist für die
Lebensdauer des Akkus optimal. Wenn Sie eine kleinere Einstellung wählen, wird die Kapazität
des Akkus zwar höher ausgenutzt, aber die Lebensdauer reduziert sich erheblich.
Hinweis: Ein voller, neuer 12 V-Akku hat eine Spannung von ca. 13,5 - 14 V.
Wichtig:
Das Modul schaltet immer erst mit einer Zeitverzögerung, damit es nicht wegen kurzfristiger
Spannungsschwankungen aufgrund kurzfristiger Stromerhöhungen ab- und wieder einschaltet.
Bitte warten Sie bei der Einstellung immer ein paar Minuten, bis das Modul reagiert.
Checkliste für Fehlersuche:
Wenn Sie zu dünnes Kabel verwenden oder die Kabel zu lang sind, dann kommt es zu Span-
nungsverlusten im Kabel und das Modul schaltet ständig ab!
Wichtiger Hinweis:
Die Anschlüsse der angeschlossenen Last dürfen nicht mit einer „Masse“ (Chassis) verbunden
werden. Grund: Das Modul schaltet den Minuspol ein oder aus. Wenn diese Anschlüsse jeweils
mit „Masse“ verbunden sind, dann würde das Modul durch den „Masseanschluss“ überbrückt
werden und wäre wirkungslos.
WichtigeMontagehinweise,bittebeachten!
Je nach Belastung kann sich das Modul mehr oder weniger erwärmen. Die Wärme entsteht an der
Alu-Platte am Boden des Moduls und muss gemäß Einbauanleitung unter bestimmten Umstän-
den durch die Montage auf eine Kühläche gekühlt werden.
Dabei ist es wichtig, dass das Modul mit 4 Schrauben M3 oder Blechschrauben 2,9 mm plan auf
ein kühlendes, planes Kühlblech montiert wird. Das kann auch die Rückwand eines Metallgehäu-
ses sein. Wichtig ist, dass sich die Alu-Unterseite des Moduls dabei nicht verzieht! Sie dürfen also
keine größeren Schrauben nehmen und die Löcher am Modul aufbohren.
Die Schraubenköpfe müssen auf dem Blech des Moduls auiegen und
nicht auf dem Plastikrand des Moduls! Bei der Montage darf sich das Modul auch nicht verziehen
(wenn der Untergrund nicht plan ist). Der Grund: Auf der Innenseite des Alu-Bodens des Moduls
sind über einer dünnen Isolierschicht direkt die elektronischen SMD-Bauelemente aufgelötet und
wenn sich der Aluboden des Moduls verzieht, lösen sich die Lötstellen und das Modul geht defekt.
Bitte achten Sie auch darauf, dass die in der Beschreibung als maximal angegebene Temperatur
der Bodenplatte nicht überschritten wird! Ansonsten muss eine größere Kühlplatte angeschraubt
werden!
Technische Daten:
Betriebsspannung: 12 V Akku | Max. Schaltleistung: 20 A (10 A ohne Kühlung, 20 A mit zu-
sätzlicher Kühlung) | Abschaltspannung: einstellbar ca. 10,4 - 13,3 V | Wiedereinschaltspan-
nung: ca. 0,8 V (±0,3 V) höher als die eingestellte Abschaltspannung | Abschaltelement: Pow-
er-MOS-Transistor in der Minusleitung | Eigenstromverbrauch: <0,7 mA im Aus-Zustand, <1,6
mA im Ein-Zustand (LED leuchtet) | Maße: ca. 87 x 60 x 33 mm (mit Befestigungsboden)
GB
Intended use:
Protection of a car battery against total discharge through connected consumers in summer
houses, camping tents, parking caravans etc.
Mounting instructions:
The module is installed in such a manner that it is not exposed to humidity, strong vibrations or
great heat. The connections are linked with the battery and consumer according to the drawing.
Please use cables with a sufcient cross section (if possible >1.5 mm²), so that a too high loss of
voltage in the cable is avoided.
It is absolutely necessary to superpose a safety fuse according to the drawing!
Attention: Short-circuits or overload on the consumer side of the module may cause that the
module will be damaged and then does not switch off any longer! Due to the fact that the function
of each module has been tested thoroughly before dispatch, replacement at our expense is not
possible in such cases or in case of damage due to too high voltage (>15 V)!
The metal base plate of the module may heat up depending on the load. No additional cooling
is required for load currents up to approx. 10 A. The module should, however, be installed “well
ventilated” so that any heat that may possibly occur is carried off from the metal plate through
circulation of air. In case of higher currents 10 - 20 A the module has to be mounted with a metal
plate planely on another larger metal plate so that the heat will be carried off. We recommend
a plate of approx. 10 x 15 x 0.5 cm or the like with a similar cooling effect. The base plate of the
module must not heat up to more than 70°C during continuous operation.
The interrupting voltage may be adjusted with the small adjustable capacitor next to the plug-in
connections. If the controller is turned completely to the left stop, the module disconnects at
approx. 10.4 V (±0.3 V) and at the right stop at approx. 13.3 V (±0.3 V). Voltages lying in between
can be adjusted continuously. We recommend to set the controller to a middle position. The
module then disconnects at approx. 11.7 V (±0.3 V) and this is optimal for the lifetime of the ac-
cumulator. When choosing a lower adjustment the capacity of the accumulator is indeed utilized
to a higher extent but the lifetime reduces considerably.
Note: a full new 12 V-battery has a voltage of approx. 13.5 - 14 V.
Important:
The module always connects with a time delay at rst so that it does not disconnect and connect
again due to short-term voltage uctuations because of short-term current increases. At this ad-
justment please always wait a couple of minutes until the module reacts.
Check list for troubleshooting:
The usage of cables which are too thin or too long may cause a loss of voltage in the cable and
thus the module switches off continuously!
Important information:
The connections of the connected load must not be connected with “earth” (chassis). Reason:
The module switches the negative pole on or off. If these connections are connected with “earth”
in each case, the module would be bypassed through the “earth connection” and would be in-
effective.
Importantinstallationinstructions,pleasenote!
Depending on the load the module heats up. The heat is dissipated from the aluminum plate at
the bottom of the module. Under certain circumstances it must be mounted on a cooling surface
according to installation instructions.
It is important that the module is xed with 4 M3 screws (or 2.9 mm metal screws) on the cooling
surface. This may be the back wall of a metal casing. The aluminum plate on the bottom of the
module must not bend, do not use larger screws and do not drill larger holes. The screw heads
must rest on the plate of the module, rather than on the plastic edge of the module! During as-
sembly, the module should not be curled up (if the ground is not at). The reason: on the inside of
the aluminum base of the module the thin insulating layer are directly soldered on the electronic
SMD components. When the aluminum oor of the module curls up, the joints and the module
start loosen and the module is defective. Please ensure that the maximum specied temperature
(as specied in the module‘s description) is not exceeded. Otherwise apply a larger cooling plate.
Technical data:
Operating voltage: 12 V battery | Max. switching capacity: 20 A (10 A without cooling, 20 A with
additional cooling) | Interrupting voltage: adjustable approx. 10.4 - 13.3 V | Resetting voltage:
approx. 0.8 V (±0.3 V) higher than the adjusted interrupting voltage | Cutoff element: power
MOS transistor in the negative line | Own current consumption: <0.7 mA in OFF condition, <1.6
mA in ON condition (LED lights) | Dimensions: approx. 87 x 60 x 33 mm (with mounting bottom)
ES
Uso previsto:
Protección de una batería de coche contra descarga total por dispositivos conectados en cenado-
res, tiendas de camping, caravanas aparcadas, etc.
Instrucciones de montaje:
Instalar el módulo de manera que no sea expuesto a humedad, vibraciones vigorosos o fuerte
calor. Unir las conexiones con la batería y el dispositivo consumidor según el dibujo. Emplear
cables con un corte transversal suciente (si posible >1,5 mm²) para evitar pérdidas de tensión
demasiado altas en el cable.
¡Es absolutamente necesario preconectar un fusible según el dibujo!
¡Atención: Cortocircuitos o sobrecarga al lado del dispositivo consumidor del módulo pueden
causar un defecto del módulo que entonces no desconecta más! ¡Puesto que la función de cada
módulo fue examinada con esmero antes del envío, un reemplazo a título de complacencia no es
posible ni en estos casos ni en caso de desperfecto por tensión demasiado alta (>15 V)!
La placa metálica del módulo se puede calentar según la carga. En caso de corrientes de carga
hasta aprox. 10 A no se necesita una refrigeración adicional. Pero el módulo se debería instalar
“bien ventilado” para que calor que puede ocurrir eventualmente se derive de la placa metálica
por circulación de aire. En caso de corrientes más altas de 10 - 20 A, el módulo se debe montar
con la placa metálica planamente sobre una otra placa metálica grande para que el calor sea
derivada. Recomendamos una placa de aprox. 10 x 15 x 0,5 cm o algo semejante con un efecto
de refrigeración similar. La placa de base del módulo no se debe calentar a más de 70°C durante
Entsorgung:
Wenn das Gerät entsorgt werden soll, darf es nicht in den Haus-
müll geworfen werden. Es muss an Sammelstellen für Fernseh-
geräte, Computer usw. entsorgt werden (bitte erkundigen Sie
sich in Ihrem Gemeindebüro oder in der Stadtverwaltung nach
Elektronik-Müll-Sammelstellen).
Disposal:
This device may not be disposed with the household waste. It
has to be disposed at collecting points for television sets, com-
puters, etc. (please ask your local authority or municipal autho-
rities for these collecting points for electronic waste).
LED an = Batterie aufgeladen
LED on = battery full
LED aus = Batterie ist entladen
LED off = battery is discharged
• Ausschalt Justierung
• Switch off adjustment
(ca. | approx.)
ANSCHLUSSBEISPIEL | CONNECTION EXAMPLE
P / Module / M148A / Beschreibung / 18038DI / Karton 1 (M148A) / Ver. 005
www.kemo-electronic.de
1/2
190 095
DE | Wichtig! Die Alu-Grundplatte darf
keinen mechanischen Spannungen aus-
gesetzt werden (keine Löcher bohren,
nicht auf unebene Kühläche schrauben
usw.). Auf der Innenseite der Alu-Grund-
platte sind direkt anliegend empndliche
elektronische Bauteile montiert, die bei
mechanischen Bewegungen defekt wer-
den und das Modul dann nicht mehr
arbeitet!
GB | Important! The aluminium base
plate must not be exposed to mecha-
nical tension (do not drill holes, do not
screw on an uneven cooling surface,
etc.). Sensitive electronic components
are mounted directly adjacent on the in-
side of the aluminium base plate, which
become defective in case of mechanical
movements and the module then won’t
work any longer!
*Schrauben nicht enthalten | screws not included
Hinweis: Bevor das Modul oder das Gerät in Betrieb
genommen oder zum ersten Mal installiert wird, muss
die ordnungsgemäße Funktion des Moduls oder des
Geräts von der Person überprüft werden, die das Teil
installiert oder in Betrieb nimmt.
Note: Before putting the module or device into opera-
tion, or installing it for the rst time, the proper functi-
on of the module or the device must be checked by a
person who installs the part or puts it into operation.
• Sicherung
• Fuse
20A
la marcha continua.
Vd. puede ajustar la tensión de desconexión con el pequeño trimmer al lado de las
conexiones de enchufe. Al girar el regulador completamente al tope a la izquierda, el
módulo desconecta a aprox. 10,4 V (±0,3 V) y al tope a la derecha a aprox. 13,3 V (±0,3
V). Las tensiones que están en medio se pueden ajustar con progresión continua. Reco-
mendamos poner el regulador a una posición media. Entonces el módulo desconecta a
aprox. 11,7 V (± 0,3 V) y eso es óptima para la vida útil del acumulador. Si Vd. elige un
ajuste más pequeño, la capacidad del acumulador se utiliza sin duda a un nivel más
alto pero la vida útil se reduce considerablemente.
Nota: Un nuevo acumulador 12 V pleno tiene una tensión de aprox. 13,5 - 14 V.
Importante:
El módulo siempre conecta solamente con un retraso para que no desconecte et conec-
te de nuevo por uctuaciones de tensión a corto plazo en virtud de alcanzes de corri-
ente a corto plazo. Al ajustar siempre esperar algunos minutes hasta que el módulo
reaccione.
Lista de comprobación para la localización de fallas:
¡Al emplear cables demasiado delgados o largos, pérdidas de tensión ocurren en el
cable y el módulo desconecta permanentemente!
Información importante:
Ambas conexiones de la carga conectada no se deben conectar con “masa” (chasis).
Razón: El módulo conecta o desconecta el polo negativo. Si estas conexiones son
conectadas con “masa” respectivamente, el módulo sería puenteado por la “conexión
a masa” y sería inecaz.
¡Instruccionesdemontajeimportantesatenerencuenta!
El módulo puede calentarse más o menos dependiente de la carga. El calor se desar-
rolla a la placa de aluminio al fondo del módulo y se debe refrigerar bajo ciertas cir-
cunstancias según las instrucciones de instalación por el montaje sobre una supercie
de refrigeración.
En este contexto es importante de montar el módulo con 4 tornillos M3 o tornillos de
chapa de 2,9 mm planamente sobre una chapa refrigerante y plana. Eso puede ser
también la pared dorsal de una caja metálica. ¡Es importante en este contexto que
la parte inferior de aluminio del módulo no se combe! Pues Vd. no debería emplear
tornillos más grandes y no abrir los agujeros al módulo. ¡Las cabezas de tornillo deben
apoyarse sobre la chapa del módulo y no sobre el borde plástico del módulo! Durante
el montaje el módulo no se debe combar tampoco (si el subsuelo no es plano). La ra-
zón: Los componentes electrónicos SMD se han soldado directamente sobre una capa
aislante delgada al lado interior del fondo de aluminio del módulo y si el fondo de alu-
minio del módulo se comba, se soltan las soldaduras y el módulo se torna defectuoso.
¡Presta también atención a lo que la temperatura de la placa de base indicada como
máximo en la descripción no se excede! ¡Por lo demás, se debe atornillar una placa de
refrigeración más grande!
Datos técnicos:
Tensión de servicio: acumulador 12 V | Potencia de ruptura máxima: 20 A (10 A sin
refrigeración, 20 A con refrigeración adicional) | Tensión de desconexión ajustable:
aprox. 10,4 - 13,3 V | Tensión de reconexión: aprox. 0,8 V (±0,3 V) más que la tensión
de desconexión ajustada | Elemento de desconexión: Power MOS transistor en la línea
negativa | Consumo de electricidad independiente: <0,7 mA en estado “desconecta-
do”, <1,6 mA en estado “conectado” (LED se ilumina) | Medidas: aprox. 87 x 60 x 33
mm (con fondo de jación)
FR
Usage prévu:
Protection d’une batterie pour auto contre décharge profonde par dissipateurs rac-
cordés en pavillons, tentes de camping, caravanes garés, etc.
Instructions d’assemblage:
Installer le module de manière que qu’il ne soit pas exposé ni à l’humidité, ni aux vi-
brations puissants ni à chaleur forte. Liez les raccords avec la batterie et le dissipateur
selon le dessin. Veuillez employer des câbles avec une coupe transversale sufsante (si
possible >1,5 mm²) pour éviter des pertes de charge trop hautes dans le câble.
Il est absolument nécessaire d’intercaler un fusible de sécurité selon le dessin!
Attention: Des court-circuits ou surcharge de côté du dissipateur du module peuvent
causer un défaut du module qu’ensuite ne déconnecte plus! Comme la fonction de
chaque module était examiné soigneusement avant l’envoi, un remplacement gratuit
n’est pas possible en ces cas, ni en cas d’endommagement par une tension trop haute
(>15 V)!
La plaque de base métallique du module peut chauffer selon la charge. En cas de char-
ges de courant jusqu’à env. 10 A un refroidissement additionnel n’est pas nécessaire.
Mais on devrait installer le module « bien ventilé » de sorte que chaleur qui apparaît
éventuellement puisse être déversée de la plaque métallique par circulation d’air. En
cas de courants plus hauts de 10 - 20 A il faut monter le module avec la plaque métal-
lique planement sur une autre plaque métallique plus grande an que la chaleur soit
déversée. Nous recommandons une plaque d’env. 10 x 15 x 0,5 cm ou quelque chose
semblable avec un effet de refroidissement similaire. Pendant la marche continue la
plaque de base du module ne doit pas chauffer à plus de 70°C.
Vous pouvez ajuster la tension de rupture avec le petit condensateur ajustable à côté
des bornes à che. Quand le régulateur est tourné complètement à l’arrêt à la gauche,
le module déconnecte à env. 10,4 V (±0,3 V) et à l’arrêt à droite à env. 13,3 V (±0,3 V).
Les tensions qui se trouvent entre les deux peuvent être réglées en continu. Nous re-
commandons de mettre le régulateur à position centrale. Ensuite le module déconnecte
à env. 11,7 V (±0,3 V) et ceci est optimal pour la durée de vie de l’accu. Si vous choi-
sissez un ajustage plus bas, il est vrai que la capacité de l’accu est exploitée plus haut
mais la durée de vie diminue considérablement.
Renseignement: Un nouveau accu 12 V plein a une tension d’env. 13,5 - 14 V.
Important:
Le module commute toujours avec un retard an qu’il ne déconnecte et connecte de
nouveau à cause des uctuations de tension à court terme en vertu des augmentations
de courant à court terme. Lors du réglage veuillez toujours attendre quelques minutes
jusqu’à ce le module réagisse.
Liste de contrôle pour la recherche des pannes:
Quand vous employez des câbles trop minces ou trop longs, des pertes de charge se
montrent dans le câble et le module déconnecte continuellement!
Indication importante:
Il ne faut pas connecter les raccords de la charge raccordée avec « masse » (châs-
sis). Raison: Le module connecte ou déconnecte le pôle négatif. Si ces raccords sont
connectés avec « masse » chaque fois, le module serait ponté par la « connexion à la
masse » et serait sans effet.
Indicationsd’assemblageimportantesàobserver!
Le module peut chauffer plus ou moins selon la charge. La chaleur se produit à la pla-
que d’aluminium au fond du module et il faut la réfrigérer éventuellement par la monter
sur une supercie réfrigérante.
Dans ce contexte il est important de monter le module avec 4 vis M3 o des vis à tôle 2,9
mm planement sur une tôle de refroidissement plane. Ceci peut aussi être le panneau
arrière d’un boîtier métallique. Il est important dans ce contexte que la partie inférieure
d’aluminium du module ne se voile pas! Donc il ne faut pas prendre des vis plus gran-
des et percer les troux au module. Les têtes de vis doivent reposer sur la tôle du module
et pas sur le bord plastique du module! Le module ne se doit pas voiler non plus lors du
montage (quand le sous-sol n’est pas plan). La raison: Les composants électroniques
SMD sont brasés directement au-dessus d’une mince chape à la côté intérieur du fond
d’aluminium du module et si le fond d’aluminium du module se voile, les brasures
se délient et le module devient défectueux. Veuillez aussi faire attention à ce que la
température de la plaque de fond indiquée comme maximum dans la description ne
soit pas excéder! Autrement il faut visser une plaque réfrigérante plus grande.
Données techniques:
Tension de service: accu 12 V | Capacité de rupture max.: 20 A (10 A sans refroidis-
sement, 20 A avec refroidissement additionnel) | Tension de rupture: ajustable d’env.
10,4 - 13,3 V | Tension de réenclenchement: env. 0,8 V (±0,3 V) plus que la tension
de rupture ajustée | Élément de déconnexion: transistor de type Power MOS dans la
ligne négative | Consommation d’électricité propre: <0,7 mA en état « arrêt », <1,6
mA en état « marche » (DEL est allumée) | Dimensions: env. 87 x 60 x 33 mm (avec
fond de xation)
NL
Speciale toepassing:
Beschermd uw accu bij een te hoog stroom verbruik (bijv. op de camping met verlich-
ting).
Montage tips:
Bij montage van het moduul moet gelet worden op vochtigheid, trillingen en hitte. Dit
moet zoveem als mogelijk voorkomen worden. Het moduul wordt volgens aansluitsche-
ma aan het verbruiksapparaat en de accu aangesloten. Gebruik een zo dik mogelijke
draad (dikker dan >1,5 mm²), om zo weinig mogelijk spanningsverlies te hebben door
de draad.
Het is aan te raden om een zekering volgens tekening te monteren.
Let op: Bij kortsluiting of overbelasting (>15 V) van het verbruiksapparaat aan de kant
van het moduul kan er voor zorgen dat het moduul defect wordt en niet meer uitscha-
keld. Omdat ieder moduul voor verzending zorgvuldig is gecontroleerd is er geen aan-
spraak op garantie of vergoeding.
De metalen bodemplaat kan bij het moduul, afhankelijk van de belasting, opwarmen.
Tot een laadstroom van ca. 10 A is geen extra koeling verplicht, maar moet zo worden
gemonteerd dat er een goede ventilatie aanwezig is. Bij hoge stromen 10 - 20 A moet de
metalen plaat van het moduul op een andere grotere plaat gemonteerd worden, zodat
de warmte afgevoerd kan worden. Aan te raden is een metalen plaat van ca. 10 x 15
x 0.5 cm, of iets anders met een goede koeling, zodat de bodemplaat van het moduul
niet boven de 70°C uitkomt.
U kunt met een instelpotmeter die naast de faston aansluiting zit, de uitschakelspan-
ning instellen. Als de instelpotmeter helemaal naar links gedraait is, schakelt het mo-
duul bij ca. 10.4 V (±0.3 V) uit, en bij het helemaal naar rechts draaien ca. 13.3 V (±0.3
V) uit, daar tussen kan traploos de gewenste spanning ingesteld worden. Wij raden aan
de instelpotmeter in het midden te regelen, ca, 11.7 V (±0.3 V), dit geeft een langer
levensduur voor de accu. Mocht u voor een kortere instelling kiezen, wordt er meer van
de capaciteit gebruik gemaakt, wat inhoud dat de levensduur van de accu beduidend
korter is.
Tip: een “volle” accu, nieuwe 12 V accu heeft een spanning van ca. 13.5 - 14 V.
Belangrijk:
Het moduul schakelt in altijd met een tijdvertraging, zodat het door kortstondige be-
lastingen, niet iedere keer in- en uitschakelt. Wacht altijd enkele minuten totdat het
moduul reageert.
Fout zoek controle lijst:
Als u een te dunne kabel gebruikt of de kabel is te lang, krijgt u spanningsverlies en het
moduul schakeld constant uit.
Belangrijke tips:
De aansluitingen van aangesloten apparaten mogen niet aan “massa” of chassis ver-
bonden zijn. Reden: het moduul schakelt de minpool aan of uit. Als dit toch met de
“massa” verbonden is, dan zal het moduul door deze aansluiting weggedrukt worden
en functioneert niet.
Zeerbelangrijkemontagetips,moetzorgvuldiggelezenworden!
Afhankelijk van de belasting wordt het moduul meer of minder warm. Deze warmte
zit aan de onderkant op het aluminium van het moduul, en kan extra gekoeld worden
d.m.v. een koelplaat.
Het moduul moet dan met 4 stuks M3 - of 2.9 mm schroeven op een vlak koelblik
gemonteerd worden. Dit kan ook de achterwand van een metalen behuizing zijn. U mag
geen grotere schroeven of de gaten van het moduul opboren! De schroefkop moet goed
contact maken met het aluminium, en niet met de plastik rand van het moduul. Bij mon-
tage van het moduul moet deze altijd 100% vlak tegen de koeling aan liggen. Reden
hiervoor is, dat de aan de binnenkant van het aluminium plaat in het moduul de SMD
onderdelen direct verbonden zijn met deze plaat, voor optimale warmte afdracht. Als
deze onderdelen geen warmte afdracht zouden hebben, dan zijn de direct defect. Dus
koeling of beter gezegd extra koeling is aan te bevelen, en houd de maximale tempe-
ratuur zie begeleidende beschrijving goed in de gaten. Als de temperatuur toch hoger
wordt dan in de beschrijving moet er beter gekoeld worden!
Technische gegevens:
Voedingsspanning: 12 V accu | Max. schakelstroom: 20 A (10 A zonder koeling, 20 A
d.m.v. extra koeling die niet bijgeleverd is) | Uitschakelspanning: instelbaar ca. 10.4
- 13.3 V | Nieuwe inschakelspanning: moet ca. 0.8 V (±0,3 V) hoger zijn dan de inge-
stelde uitschakelspanning | Uitschakel component: Power-MOS transistor in de min
leiding | Ruststroom verbruik: <0.7 mA in uit schakeling, <1.6 mA in aan schakeling
(led licht op) | Afmeting: ca. 87 x 60 x 33 mm (met bodemplaat)
PT
Uso conforme as disposições legais:
Protege uma bataria de carro contra cargas baixas através ligados consumidores em
caramanchão, tendas de campismo, carros de campismo estacionados etc.
Instruções de montagem:
O modulo é montado de modo que este não esteja exposto a humidade, vibrações
fortes ou grandes calores. As ligações são ligadas com a bataria em volta do consu-
midor conforme no desenho. Por favor usar um cabo com suciente corte transversal
(possível >1,5 mm²) para não aparecerem altas perdas de tensão no cabo.
È necessário intercalar um dispositivo de segurança conforme no desenho!
Atenção: curtos circuitos ou sobrecargas do lado do consumidor podem levar a destruir
o modulo e este não desligar! Como cada modulo antes da expedição foi examinado ás
suas funções, não á neste caso e também numa danicação com alta-tensão (>15 V)
uma garantia de substituição possível!
A placa base metálica do modulo pode conforme a carga aquecer. Em cargas electri-
cas até ca. 10 A, não é necessário uma suplementar refrigeração. O modulo deve ser
montado num lugar bem arejado, para que o calor através da circulação de ar seja
desviado da placa metálica. Em altas correntes 10 - 20 A deve o modulo deve com a
placa metálica ser contruida numa outra maior placa metálica, para que o calor seja
desviado. Recomenda-mos uma placa de ca. 10 x 15 x 0,5 cm ou coisa parecida com
parecido efeito refrigerente. A placa base do modulo em funcionamento contínuo não
deve aquecer mais que 70°C.
Pode com um pequeno condensador de compensação ao lado da conexão incaixável
pode ajustar a tensão de circuito de desligamento. Quando o regulador está todo en-
costado para o lado esquerdo desliga o modulo em ca. de 10,4 V (±0,3 V) e se tiver todo
encostado para o lado direito então desliga este em ca. 13,3 V (±0,3 V). Pode entre
o contínuo progressivo sem graduação regular a tensão. Nós recomenda-mos levar o
regulador a posição a posição central. Então desliga o modulo em ca. 11,7 V (±0,3
V) e isto é para a duralidade do acumulador optimal. Quando escolher um pequeno
ajuste, é a capacidade do acumulador sem duvida mais aproveitada, mas a duralidade
reduz-se mais.
Indicação: um cheio novo 12 V acumulador tém uma tensão de ca. 13,5 - 14 V.
Importante:
O modulo liga sempre em primeiro com um curto prazo, para que demoras na utuação
de tensão, por motivo demora a corrente a ligar e desligar. Por favor espere sempre no
ajuste alguns minutos, até o modulo reagir.
Lista de instruções para localizar defeitos:
Quando usar um cabo muito no ou o cabo é muito comprido, então á perdas de tensão
no cabo e o modulo desliga permanentemente.
Indicações importantes:
As ligações da ligada carga não deve ser ligada com “massa” (chassi). Motivo: O modulo
liga e desliga o polo negativo. Quando estas ligações são ligadas respectivamente com
“massa” então fáz o modulo através da “terminal de terra” curto-circuitar e ca inecaz.
Importantesindicaçõesdemontagem,tomaratenção!
Conforme a carga pode o modulo aquecer mais ou menos. O aquecimento é produzido
na placa de aluminío no fundo do modulo e deve conforme a instrução de montagem
sobre determinadas circunstâncias através da montagem de uma superfície de refri-
geração, ser arrefecido.
Neste caso é importante, que o modulo seja montado com 4 parafusos M3 ou parafu-
sos de folha metálica 2,9 mm plano num arrefecimento plano na chapa de refrigeração.
Pode ser tambem a parede traseira de uma caixa metálica. Importante é que a parte de
baixo do alumínio do modulo não se transformar! Não pode usar parafusos maiores e
não furar buracos no modulo. A cabeça dos parafusos devem ser colocados em cima da
chapa do modulo mas não nas bordas de plástico do modulo! Na montagem tambem o
modulo não se deve transformar (quando a base da superfície não é plana). O motivo:
no lado interior do fundo do alumínio do modulo são sobre uma na camada isoladora
directo os electrónicos SWD–componentes soldados e quando o fundo de alumínio do
modulo se transforma então são destruidas as soldaduras e o modulo ca danicado.
Por favor tome atenção que descrevida como máxima dada temperatura da alcapação
não seja excedida! Senão deve der aparafusada uma maior placa de refrigeração!
Dados técnicos:
Tensão de serviço: 12 V acumulador | Máx. capacidade de ruptura: 20 A (10 A sem
refrigerente, 20 A com suplementar refriregente) | Tensão de circuito de desconexão:
ajustável ca. 10,4 - 13,3 V | Novamente tensão de conexão: ca. 0,8 V (±0,3 V) mais
alta que a ajustada tensão de circuito de desconexão | Elemento de desconexão:
Power-MOS-transistor na linha negativa | Consumo de electricidade própria: <0,7 mA
desligado, <1,6 mA ligado (LED brilha) | Medida: ca. 87 x 60 x 33 mm (solo de xação)
PL
Użytkowaniezgodnezprzeznaczeniem:
Ochrona akumulatora samochodowego przed całkowitym rozładowaniem wskutek po-
dłączenia odbiorników w altanach ogrodowych, namiotach na campingu, zaparkowa-
nych kamperach itp.
Instrukcjamontażu:
Moduł należy wbudować tak, aby nie był on wystawiony na wilgoć, silne drgania ani
wysokie temperatury. Przyłącza zostają połączone z akumulatorem i odbiornikiem tak,
jak pokazano to na rysunku. Prosimy użyć kabla o wystarczająco dużym przekroju (w
miarę możliwości >1,5 mm²), aby nie występowały w nim zbyt duże straty napięcia.
Przed czujnikiem należy koniecznie włączyć bezpiecznik tak, jak pokazano to na rysun-
ku!
Uwaga: Zwarcia czy przeciążenia po stronie modułu zwróconej ku odbiornikom, mogą
prowadzić do tego, że moduł zostanie uszkodzony i przestanie odłączać! Ponieważ dzi-
ałanie każdego modułu zostało przed wysyłką starannie sprawdzone, tak więc w takich
przypadkach, a także w razie uszkodzenia z powodu zbyt wysokiego napięcia (>15 V)
wymiana z względów grzecznościowych nie jest możliwa!
Metalowa płyta podstawy modułu może się rozgrzewać w zależności od obciążenia. W
przypadku prądów obciążenia do ok. 10 A żadne dodatkowe chłodzenie nie jest ko-
nieczne. Moduł powinien jednak być wbudowany w miejscu dobrze wentylowanym, aby
powstające ciepło mogło zostać odprowadzone z metalowej płytki przez cyrkulujące po-
wietrze. W przypadku wyższych prądów 10 - 20 A moduł z metalową płytką zamontowany
musi zostać płasko na innej, większej metalowej płytce, aby mogło zostać odprowadzo-
ne ciepło. Zalecamy płytkę ok. 10 x 15 x 0,5 cm albo podobną z podobnym skutkiem
chłodzącym. Płyta podstawowa modułu nie może się podczas pracy ciągłej rozgrzewać
powyżej 70°C.
Napięcie odłączania mogą Państwo ustawić małym trymerem obok wtykanych końcówek
podłączeniowych. Jeżeli regulator jest obrócony w lewo do oporu, moduł odłącza przy
około 10,4 V (±0,3 V), a przy obróceniu w prawo do oporu przy około 13,3 V (±0,3 V).
Pomiędzy tymi położeniami można nastawiać napięcia pośrednie. Zalecamy ustawienie
regulatora w położeniu środkowym. Wówczas moduł odłącza przy około 11,7 V (±0,3 V)
i jest to wartość optymalna, jeśli chodzi o czas żywotności akumulatora. Jeżeli wybiorą
Państwo niższe ustawienie, to wprawdzie pojemność akumulatora będzie wykorzystana
w wyższym stopniu, ale jego żywotność ulega znacznemu skróceniu.
Wskazówka: W pełni naładowany, nowy akumulator 12 V ma napięcie około 13,5 - 14 V.
Ważne:
Moduł odłącza zawsze z pewnym opóźnieniem czasowym, aby odłączanie i ponowne
włączanie nie następowało na zmianę w krótkich odstępach czasu z powodu krótkot-
rwałych wahań napięcia spowodowanych krótkotrwałymi wzrostami prądu. Przy usta-
wianiu napięcia prosimy zawsze odczekać przez kilka minut, zanim moduł zareaguje.
Lista kontrolna przy poszukiwaniu usterek:
Jeżeli użyją Państwo zbyt cienkiego kabla, albo jeśli kable zbyt długie, wówczas
dochodzi do strat napięcia w kablu i moduł stale odłącza!
Ważnawskazówka:
Końcówki podłączonego obciążenia nie mogą zostać połączone z „masą“ (obudową).
Powód: Moduł włącza lub wyłącza biegun ujemny. Jeżeli te końcówki podłączeniowe
byłyby połączone z masą, to moduł zostałby zmostkowany przez „przyłącze masy“ i byłby
bezskuteczny.
Ważnewskazówkiprzymontażu,prosimyjewziąćpoduwagę!
W zależności od obciążenia moduł może się mniej lub bardziej rozgrzewać. Ciepło
wytwarzane jest na płytce aluminiowej na spodzie modułu i w określonych okolicznoś-
ciach musi zostać odprowadzone poprzez zamontowanie modułu na chłodzącej pow-
ierzchni zgodnie z instrukcją montażu.
Ważne przy tym jest, aby moduł został zamocowany płasko 4 śrubami M3 albo śrubami
do blachy 2,9 mm na chłodzącej, płaskiej powierzchni blaszanej. Może to być również
tylna ścianka metalowej obudowy. Ważne jest, aby aluminiowy spód modułu nie uległ
przy tym deformacji! Nie wolno więc użyć większych śrub i rozwiercać otworów na modu-
le. Łebki śrub muszą przylegać do blachy modułu a nie do plastikowego brzegu modułu!
Przy montażu moduł nie może też zostać zdeformowany (jeśli powierzchnia podłoża
nie jest płaska). Powód: Po wewnętrznej stronie aluminiowego dna modułu na cienkiej
warstwie izolacyjnej przylutowane są bezpośrednio elektroniczne podzespoły SMD i jeśli
aluminiowe dno modułu ulegnie deformacji, miejsca lutowania zostaną rozłączone i mo-
duł ulegnie uszkodzeniu. Prosimy zwrócić uwagę również na to, aby temperatura płyty
dennej, określona w opisie jako temperatura maksymalna, nie była przekraczana! W
przeciwnym razie trzeba przykręcić większą płytę chłodzącą!
Dane techniczne:
Napięcierobocze: 12 V akumulator |Maks.mocprzełączania: 20 A (10 A bez chłod-
zenia, 20 A z dodatkowym chłodzeniem) |Napięcieodłączania: regulowane ok. 10,4
- 13,3 V |Napięcieponownegowłączania: ok. 0,8 V (±0,3 V) wyższe niż ustawione na-
pięcie odłączania |Elementodłączający: tranzystor mocy MOS w przewodzie ujemnym
|Własnezużycieprądu: <0,7 mA w stanie wyłączonym, <1,6 mA w stanie włączonym
(dioda LED się świeci) | Wymiary: ok. 87 x 60 x 33 mm (z denną płytą do mocowania)
RU
Инструкцияпоприменению:
Модуль защищает аккумулятор от полного разряжения из за подключенных к нему
потребителей напр. в садовых домиках, палатках, в домиках на турбазах и т.д.
Инструкцияпомонтажу:
Монтаж модуля должен быть сделан таким образом, чтобы он не подвергался
повышенной влажности воздуха, сильным вибрациям, высокой температуре.
Аккумулятор и потребитель должны быть соединены между собой в соответствии с
монтажным чертежом. Кабель должен быть с соответствующим сечением (лучше
всего >1,5 квадратных мм), чтобы избежать потери напряжения в кабеле.
В цепь необходимо в соответствии с чертежом вставить предохранитель!
Внимание: Короткое замыкание или перегрузка со стороны потребителя, а так
же высокое напряжения на входе (>15 В), может вывести модуль из строя и он не
будет больше отключаться. Так как каждый модуль после его изготовления проходит
тщательный контроль, его замена в рамках гарантии не возможна.
Мeтaлличeскaя поверхность модуля можeт в зависимости от нaгрузки нaгрeвaться.
При нaгрузках до примерно 10 A, нe трeбуeтся дополнитeльного охлaждeния. Но
модуль в тaком случae должeн быть установлен нa хорошо провeтривaeмом мeсте,
чтобы циркулирующий воздух его обдувал. Для высоких токов 10 - 20 A нeобходимо
прибор его мeтaллической поверхностью прикрепить к радиатору. Рeкомeндуeтся
использовать радиатор гaбaритaми примeрно 10 х 15 х 0,5 см или похожий.
Мeтaлличeскaя поверхность нe должнa во врeмя рaботы нaгрeвaться больeе чeм
нa 70°Цeльсия.
Потенциометром, который нaходится рядом с контaктным разъемом, можно
нaстроить нaпряжeние отключeния. Если потенциометр повернуть влево до упора,
модуль будет отключаться при нaпряжeнии примeрно 10,4 Вольт (±0,3 Вольт), а
при врaщeнии его нaпрaво до упорa, модуль будет отключаться при нaпряжeнии
примeрно 13,3 Вольт (±0,3 Вольт). Между этими положениями вы можете плавно
настроить желаемое напряжение. Мы рекомендуем установить потенциометр
в среднем положении, это соответствует напряжению примeрно 11,7 Вольт
(±0,3 Вольт), и это способствует оптимальному сроку службы аккумулятора. Если
вы установите меньшую величину напряжения, время разрядки аккумулятора
увеличится, а продолжительность его службы значительно сократится.
Примeчaниe: Новый полностью зaряжeнный 12 Вольтный aккумулятор имет
нaпряжeниe примерно 13,5 - 14 Вольт
Важно:
Отключение модуля происхоит с задержкой, чтобы избежать непроизвольного
отключeния из за кратковременных колeбaний нaпряжeния. При настройке нужного
вам напряжения необходимо ждать несколько минут пока прибор сработает.
Списоквозможныхнеисправностей:
Если вы используете тонкий или слишком длинный кабель, то в нем происходит
потеря напряжения и модуль постоянно отключается!
Вaжноeпрeдупрeждeниe:
Проводa для потребителей запрещается соeдинять с шaсси. Причинa: Модуль
включает и отключает минусовой полюс. Если проводa нaгрузки будут соeдинeны
с шaсси, модуль будeт просто перемкнут и никакого отключения аккумулятора не
будет.
Пожалуйстаобратитевниманиенаважнуюинструкциюпомонтaжу!
В зaвисимости от нaгрузки модуль можeт нагрeвaться. Тeпло передается нa
aлюминевую пластину модуля и в зависимости от степени нагревания ее следует в
соответствии с инструкцией по монтажу закрепить на охлождающий радиатор.
При этом очeнь вaжно, чтобы модуль был зaкрeплeн 4-мя винтами с метрической
резьбой М3 или сaморeзaми 2,9 мм нa плоскую охлaждaющую плaту. В качевстве
охлождающей платы может вполне послужить стенка металлического корпуса.
Вaжно, чтобы aлюминeвaя поверхность модуля оставалась такой же ровной и
нe дeформировaлась. Так жe запрещается рассверливание отверстий для более
больших винтов и шурупов. Головки винтов должны плотно прилегать к алюминевой
плате модуля, a нe к плaстиковой кромке корпуса! При монтaжe нужно слeдить
зa тeм, чтобы модуль нe дeформировaлся (поверхность, на которую должен быть
прикручен модуль, должна быть абсолютно ровной). Причина: На внутренней
стороне aлюминeвой платы нанесен тонкий изоляционный слой, нeпосрeдствeнно
нa который припаяны элeктронные компоненты (SMD тeхнология) и любая
дeформaция aлюминeвой платы приводит к обрыву припаянных компонентов
или дорожек. Слeдитe пожaлуйстa зa тeм, чтобы не привышалась максимально
допустимая тeмпeрaтурa нагревания модуля указанная в описании! В противном
случае нeобходимо прикрепить модуль к более большому радиатору!
Техническиеданные:
Рабочеенапряжение: 12 вольтный аккумулятор |Макс.нагрузка: 20 Ампер (10 А
без охлаждения, 20 А с дополнительным радиатором) |Напряжениеотключения:
Устанавливается в диапазоне приблизительно 10,4 - 13,3 Вольт | Напряжение
включения: примерно 0,8 Вольт (±0,3 Вольт) выше, чем установленное
напряжение отключения | Отключающий элемент: Мощный MOS-транзистор
отключающий минусовой полюс |Собственноепотреблениетока: примерно <0,7
мА в отключенном состоянии, примерно <1,6 мА во включенном состоянии (горит
светодиод) |Габариты: приблизительно 87 х 60 х 33 мм (вместе с креплением)
DE | Wichtig: Bitte beachten Sie die extra beiliegenden „Allgemeingültigen Hinwei-
se“ in der Drucksache Nr. M1002. Diese enthält wichtige Hinweise der Inbetriebnah-
me und den wichtigen Sicherheitshinweisen! Diese Drucksache ist Bestandteil der
Beschreibung und muss vor dem Aufbau sorgfältig gelesen werden.
GB | Important: Please pay attention to the “General Information” in the printed
matter no. M1002 attached in addition. This contains important information star-
ting and the important safety instructions! This printed matter is part of the product
description and must be read carefully before assembling!
ES | Importante: Observar las “Indicaciones generales” en el impreso no. M1002
que se incluyen además. ¡Ellas contienen informaciones importantes la puesta en
servicio y las instrucciones de seguridad importantes! ¡Este impreso es una parte
integrante de la descripción y se debe leer con esmero antes del montaje!
FR | Important: Veuillez observer les « Renseignement généraux » dans l’imprimé
no. M1002 ci-inclus. Ceci contient des informations importantes la mise en marche
et les indications de sécurité importantes! Cet imprimé est un élément déni de la
description et il faut le lire attentivement avant l’ensemble!
NL | Belangrijk: Belangrijk is de extra bijlage van “Algemene toepassingen” onder
nr. M1002. Deze geeft belangrijke tips voor het monteren het ingebruik nemen en
de veiligheids voorschriften. Deze pagina is een onderdeel van de beschrijving en
moet voor het bouwen zorgvuldig gelezen worden.
PT | Importante: Por favor tomar atenção com o extra “Indicações gerais válidas” o
junto impresso M1002. Este contém importantes indicações a colocação em funci-
onamemto e importantes indicações de segurança! Este impresso é um elemento
da descrição que deve cuidadosamente ler antes da montagem!
PL|Ważne: Proszę przestrzegać uwag zawartych w dołączonym druku „Ogólnie obo-
wiązujące zalecenia” Nr. M1002. Broszura ta zawiera ważne informacje dotyczące
uruchomienia i bezpieczeństwa! Jest ona częścią instrukcji i musi być przed mon-
tażem dokładnie przeczytana.
RU | Важное примечание: Пожалуйста обратите внимание на отдельно
приложенные «Общедействующие инструкции» в описании Но. М1002. Это
описание содержит важные инструкции введения в эксплуатацию, и важные
замечания по безопасности. Этот документ является основной частью описания
по монтажу и должен быть тщательно прочитан до начала работы!
P / Module / M148A / Beschreibung / 18038DI / Karton 1 (M148A) / Ver. 005
2/2
Kemo Electronic GmbH, Leher Landstrasse 20, 27607 Geestland, Germany
1 / 1

Kemo Electronic M148A Assembly Instructions

Taper
Assembly Instructions