Marson MT582W 2D Ring Barcode Scanner Mode d'emploi

Marque
Marson
Modèle
MT582W 2D Ring Barcode Scanner
Catégorie
Lecteurs de codes à barres
Taper
Mode d'emploi
2D Ring
Barcode Scanner
2D Ring Barcode Scanner Quick Guide (Rev3)
P/N: 8013-0069020
INTRODUCTION GETTING STARTED ATTENTION SPECIFICATIONS
OUT OF THE BOX
Light source Visible red LED & White LED
Sensor 640 x 480 pixels
Resolution 3mil / 0.075mm
PCS 10%
Width of Field 176mm (13Mil Code39)
Depth of Field 5 Mil Code39: 50 - 150mm
13 Mil UPC/EAN: 55 - 315mm
6.67 Mil PDF417: 55 - 120mm
10 Mil DataMatrix: 50 - 120mm
15 Mil QR Code: 35 - 175mm
Dimension W27.6 x L46.2 x H26.8 mm
Housing PC+ABS
Connector USB Type-C
Interface USB HID, USB VCP
Voltage 5VDC±5%
Working Current < 200mA
Standby Current < 15mA
Operating Temp. -20 to 60°C (- 4°F to 140°F)
Storage Temp. -40 to 70°C (-40°F to 158°F)
Ambient Light 100,000 lux
Drop Durability 1.5M
Sealing IP42
Symbologies all major 1D and 2D barcodes including
GS1 UDI and Dotcode
Quick Guide
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CANADIAN DOC STATEMENT
This digital apparatus does not exceed the Class B limits for radio noise for digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de las classe B prescrites dans le
Réglement sur le brouillage radioélectrique édicté par les ministère des Communica-
tions du Canada.
CE MARKING AND EUROPEAN UNION COMPLIANCE
Testing for compliance to CE requirements was performed by an independent
laboratory. The unit under test was found compliant with all the applicable Directives,
2004/108/EC and 2006/95/EC.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
The WEEE directive places an obligation on all EU-based manufacturers and
importers to take-back electronic products at the end of their useful life.
ROHS STATEMENT OF COMPLIANCE
This product is compliant to Directive 2002/95/EC.
NON-MODIFICATION STATEMENT
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
1. Take any metals into contact with the terminals in connectors.
2. Use the scanner where any inflammable gases.
If following condition occur, immediately power off the host computer,
disconnect the interface cable, and contact your nearest dealer.
1. Smoke, abnormal odors or noises come from the scanner.
2. Drop the scanner so as to affect the operation or damage its housing.
Do Not
Do not do behavior below.
1. Put the scanner in places excessively high temperatures such as expose
under direct sunlight.
2. Use the scanner in extremely humid area or drastic temperature
changes.
3. Place the scanner in oily smoke or steam environment such as cooking
range.
4. Be covered or wrapped up the scanner in bad-ventilated area such as
under cloth or blanket.
5. Insert or drop foreign materials or water into scanning window or vents.
6. Using the scanner while hand is wet or damp.
7. Use the scanner with anti-slip gloves containing plasticizer and
chemicals or organic solvents such as benzene, thinner, insecticide etc
to clean the housing. Otherwise, it could not result fire and electrical
shock but housing may be broken and injured.
8. Scratch or modify the scanner and bend, twist, pull or heat its interface
cable.
9. Put heavy objects on interface cable.
Do not stare the light source from the scanning window or do not point the
scanning window at other people’s eyes or eyesight may be damaged
by direct exposure under the light.
Do not put the scanner on an unstable or inclined plane.
The scanner may drop, creating injuries.
Once the interface cable is damaged such as exposed or broken copper
wires, stop using immediately and contact your dealer. Otherwise, it could
result fire or electrical shock.
WARNING AND CAUTIONREGULATORY INFORMATION
Spare Velcro Strap
USB Type-C Cable
2D Ring
Barcode Scanner
Quick Guide
2D Ring
Barcode Scanner
Quick Guide
Pressing on Funtion Button allows user to quickly configure
preference for Touch-Activated Trigger Button, with the
change of LED indicator color representing different
configurations:
BUTTON PREFERENCE
Red
Blue
Purple
= Enable Left Button Only (Right-handed User)
= Enable Right Button Only (Left-handed User)
= Enable Both Buttons
Clench your fist and use your thumb to tap the
touch-activated trigger button. A gentle touch
on the button will work; there is no need to press
with force.
1. It is recommended to dry both your hand and the Velcro
strap to avoid the scanner being accidentally triggered
by moisture.
2. The following gloves have been tested to be working with
the touch-activated button: latex examination glove
antistatic glove, white cotton glove (with or without latex
coating), safety glove, and rubber glove. However, it is
still recommended to operate with bare hand or thin glove
to ensure the responsiveness of button.
3. Don’t need to tighten Velcro strap too much. Just make the
strap fit your finger so that the scanner will not easily move
while being touched for trigger. We also suggest to release
the strap from your finger for 1 minute after 2 hours of
continuous use if your finger feels uncomfortable.
BEEPER INDICATION
Single beep Good read on non-configuration
Two beeps Error
barcode
Three beeps Good read on configuration barcode
Four beeps Power-up
LED Indicator USB Type-C Connector
(with Protective Cover)
Touch-Activated
Trigger Button
Function Button
Exit Window
Velcro Strap
(for Button Preference
configuration)
BEEPER
CONTINUOUS MODE
AUTO-SENSING MODE
KEYBOARD LAYOUT
GERMAN FRENCH
ENGLISH (UK)
SPANISH ITALIAN
BRAZILIANPORTUGUESE
BELGIAN TURKISH Q
USB VCP
CR+LF
ALWAYS ON CR+LF+CR+LF
ALWAYS OFF
ENGLISH
(
USA
)
NONE
GENERAL SETTINGS READING MODE
GOOD READ BEEP ON
POWER UP BEEP ON
SETUP BEEP ON
TRIGGER MODE
GOOD READ BEEP OFF
POWER UP BEEP OFF
SETUP BEEP OFF
AIMER ILLUMINATIONSYMBOLOGIES
INTER-CHARACTER DELAY
NORMAL
ALWAYS ON
ALWAYS OFF
NORMAL
DEFAULT
NONE
SHORT LONG
INTERFACE
USB HID
ENABLE
INVERSE BARCODE
TERMINATOR
DISABLE
CR
ENABLE ALL CODES
ENABLE ALL 1D CODES DISABLE ALL 1D CODES
ENABLE ALL 2D CODES DISABLE ALL 2D CODES
DISABLE ALL CODES
CR+LF
NONELF
DEFAULT
CHECK VERSION
  • Page 1 1
  • Page 2 2

Marson MT582W 2D Ring Barcode Scanner Mode d'emploi

Marque
Marson
Modèle
MT582W 2D Ring Barcode Scanner
Catégorie
Lecteurs de codes à barres
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents