Honeywell UV2400U1000 Guide d'installation

UV2400U Air Purifier

with AirBRIGHT™ Odor Absorption

Installation

Instructions

2

Before Installing this Product

Read these instructions carefully; failure to follow them could damage the product and

cause a hazardous situation.

Installer must be a trained, experienced service technician.

WARNING: UV Light Hazard.

Harmful to bare skin and eyes. Can cause temporary or permanent loss of

vision. Never look at lamps while illuminated.

• To prevent exposure to ultraviolet light, disconnect power to the ultraviolet air

treatment system before servicing any part of the heating/air conditioning system.

• View illumination only through lamp handle or sight glass.

• Do not attempt to bypass duct mount switch.

• Do not attempt to open housing; unit is sealed to prevent ultraviolet light

exposure.

3

CAUTION: Personal Injury Hazard. HVAC power supply can cause

electrical shock.

Disconnect HVAC power supply before installing, cleaning or replacing ultraviolet

lamp(s).

CAUTION: Breakable Glass Hazard. Can cause personal injury.

• Be careful when inserting lamp(s) into lamp base.

• Wear protective gloves when handling lamp(s).

CAUTION: Personal Injury Hazard. Power supply can cause electrical

shock.

• Disconnect power supply before cleaning or replacing ultraviolet lamp(s).

• Do not open base unit or lamp handle; there are no user-serviceable compo-

nents inside.

CAUTION: UV Lamp Burn Hazard. Harmful to bare skin. Can cause severe

burns.

• Disconnect power 15 minutes before removing ultraviolet lamp(s).

4

1. UV lamp handle

2. Base

3. Foam Gasket

4. 16W UV lamp

5. AirBRIGHT™ Odor

Absorber (included

in UV2400U5000

only)

6. Bushing

7. Sight Glass

8. Warning sticker

9. 24 VAC Ballast

10. Self Tapping

Screws (3)

11. Power Cord

12. wire connectors

(not pictured)

Parts Included

4

5

2

11

9

1

8

M34596

3

7

10

6

5

Typical Mounting Locations

We recommend the UV Air Purifier be installed on the supply side duct 3–5 inches

above the A-coil, but it can also be installed on the return side if necessary. See

Figures 1 and 2.

The germicidal UV light should be positioned to shine on the surfaces that are prone

to mold growth like the A-coil, or be placed in an open area of the return duct where

there are long straight runs.

WARNING: Do not mount device in location that allows ultraviolet light to be seen

after installation other than by the UV protected lamp handle or sight glass.

Important: Some materials inside the HVAC system (including filter media, flex duct,

wiring etc.) may not be UV light resistant. Cover materials affected by UV light with UV

shielding or reflective tape.

The AirBRIGHT™ Odor Absorber unit should be oriented so that the air flows past the

UV Light first then into the AirBRIGHT Odor Absorber.

6

Fig. 1. Supply Side installation. Airflow depicted by arrows.

M34597

FURNACE AIR HANDLER

7

Fig. 2. Return Side installation. Airflow depicted by arrows.

M34621

FURNACE

AIR HANDLER

8

Option 1

Internal Mounting

IMPORTANT

Turn off main power source before installation. Model information is

printed on the Power Unit cover.

1. Unfasten panel to gain access to mounting location

2. Determine the optimal position for placement of the Air Purifier.

3. If necessary, use a utility knife to

cut the insulation on the inside of

the duct.

4. Clean surface of glue, dust, etc.

M34659

9

M34689

5. Push the AirBRIGHT™ Odor Absorber into the base until the two tabs on the side

click into place.

6. Insert Snaplamp into base.

M34685

10

8. Place the magnetic bars on the base

directly on the clean metal surface.

M34661

7. Rotate the lamp handle clockwise

until it snaps in place.

9. Use foil tape to close the cut in the

insulation as needed.

M34660

11

10. Create a 5/8 (0.625) in. hole in the

duct and pass the cord through it. Clip

the bushing provided onto the cord at

a point close to the hole. Plug the hole

with the bushing.

M34601

M34602

12. Find a suitable location on the

outside of the duct-work near the

UV Lamp installation and apply the

warning/lamp replacement sticker.

13. Drill a 1/2 in. hole through the circle

on the sticker. Press the UV sight

glass into hole.

11. Secure access panel to the duct work.

12

Option 2

External Mounting for Metal Duct Applications

1. Use the gasket to mark the duct openings. Cut and remove openings, making sure

to cut 1/8-inch outside of the markings to create enough room for the product. If

using a hole saw to cut circular opening, use a 2-inch diameter bit.

M34604

13

M34687

2. Push the AirBRIGHT™ Odor Absorber

into the base until the two tabs on the

side click into place.

M34685

3. Remove one side of the backing from the gasket and stick

gasket on the ductwork so that the openings line up.

14

4. Peel away the other side of the backing on the gasket and insert AirBRIGHT™ into

the duct until the base sticks securely to the gasket.

5. Secure the base to the ductwork using self-tapping screws.

6. Insert lamp into base and turn handle clockwise to lock in place.

M34661

7. Find a suitable location on the outside of the duct-work near the UV Lamp

installation and apply the warning/lamp replacement sticker.

15

Option 3

Duct Board Mounting: For Duct Board Applications Only

1. Use the gasket to mark the duct openings. Cut and remove openings, making sure

to cut 1/8-inch outside of the markings to create enough room for the product. If

using a hole saw to cut circular opening, use a 2-inch diameter bit.

M34604

16

M34853

M34685

2. Push the AirBRIGHT™ Odor Absorber into the base until the two tabs on the side

click into place.

3. Bend metal tabs of duct board adapter

over the holes cut in the duct board.

17

M34852

4. Remove one side of the backing from the gasket

and stick gasket on the duct board adapter so

that the openings line up.

5. Peel away the other side of the backing on the gasket and

insert AirBRIGHT into the duct until the base sticks securely

to the gasket.

6. Secure the base to the ductwork using self tapping screws.

7. Insert lamp into base and turn handle clockwise to lock in

place.

8. Find a suitable location on the outside of the duct-work

near the UV Lamp installation and apply the warning/lamp

replacement sticker.

M34661

18

Power Supply Installation

• Find a suitable location for the power supply and mount using the self-tapping

screws.

• Use the wiring diagram on the next page to connect to power.

• When all the other components are properly installed connect the UV lamp cable

to the power supply cable.

M34663

ALIGN FLANGES

2.

1.

• Make sure the flanges are aligned

and then push the connectors

firmly together. A tight connection

ensures a proper water-resistant

seal. See image at right.

• Turn on the power and use the

lamp handle or sight glass to

confirm that the UV Lamp is

operating.

19

Power Supply Wiring

WARNINGS:

• Draws 16 VA, do load calculation to determine if a separate transformer is

needed.

• Systems with high 24 VAC loads may require the installation of a separate 24

VAC transformer to power the UV light.

• Always use a separate 24 VAC transformer with “communicating” air systems.

M34605

NOTE: IMPORTANT! MUST BE WIRED TO CONSTANT POWER. DO NOT CONNECT TO

BLOWER RELAY.

24 VAC

TRANSFORMER

BALLAST

24 VAC

COMMON

HOT

BLACK

RED

CONSTANT

110V

20

Maintenance

Note: Lamps should be replaced every year. UV lamps will continue to emit visible

light but lose germicidal effectiveness after approximately one year.

Changing UV Lamp

1. Disconnect the power to your heating and cooling system.

2. Unplug or turn off power to your UV System and allow the lamp to cool for at least

15 minutes.

3. Rotate the lamp handle counterclockwise, as shown below, and gently pull the

lamp handle to remove the lamp.

M34606

M34609

La page charge ...

Honeywell UV2400U1000 Guide d'installation

Ce manuel convient également à

Honeywell UV2400U1000 Guide d'installation

dans d''autres langues

Documents connexes