Honeywell UV2400U1000 Guide d'installation

Taper
Guide d'installation

Ce manuel convient également à

UV2400U Air Purifier
with AirBRIGHT™ Odor Absorption
Installation
Instructions
2
Before Installing this Product
Read these instructions carefully; failure to follow them could damage the product and
cause a hazardous situation.
Installer must be a trained, experienced service technician.
WARNING: UV Light Hazard.
Harmful to bare skin and eyes. Can cause temporary or permanent loss of
vision. Never look at lamps while illuminated.
• To prevent exposure to ultraviolet light, disconnect power to the ultraviolet air
treatment system before servicing any part of the heating/air conditioning system.
• View illumination only through lamp handle or sight glass.
• Do not attempt to bypass duct mount switch.
• Do not attempt to open housing; unit is sealed to prevent ultraviolet light
exposure.
3
CAUTION: Personal Injury Hazard. HVAC power supply can cause
electrical shock.
Disconnect HVAC power supply before installing, cleaning or replacing ultraviolet
lamp(s).
CAUTION: Breakable Glass Hazard. Can cause personal injury.
• Be careful when inserting lamp(s) into lamp base.
• Wear protective gloves when handling lamp(s).
CAUTION: Personal Injury Hazard. Power supply can cause electrical
shock.
• Disconnect power supply before cleaning or replacing ultraviolet lamp(s).
• Do not open base unit or lamp handle; there are no user-serviceable compo-
nents inside.
CAUTION: UV Lamp Burn Hazard. Harmful to bare skin. Can cause severe
burns.
• Disconnect power 15 minutes before removing ultraviolet lamp(s).
4
1. UV lamp handle
2. Base
3. Foam Gasket
4. 16W UV lamp
5. AirBRIGHT™ Odor
Absorber (included
in UV2400U5000
only)
6. Bushing
7. Sight Glass
8. Warning sticker
9. 24 VAC Ballast
10. Self Tapping
Screws (3)
11. Power Cord
12. wire connectors
(not pictured)
Parts Included
4
5
2
11
9
1
8
M34596
3
7
10
6
5
Typical Mounting Locations
We recommend the UV Air Purifier be installed on the supply side duct 3–5 inches
above the A-coil, but it can also be installed on the return side if necessary. See
Figures 1 and 2.
The germicidal UV light should be positioned to shine on the surfaces that are prone
to mold growth like the A-coil, or be placed in an open area of the return duct where
there are long straight runs.
WARNING: Do not mount device in location that allows ultraviolet light to be seen
after installation other than by the UV protected lamp handle or sight glass.
Important: Some materials inside the HVAC system (including filter media, flex duct,
wiring etc.) may not be UV light resistant. Cover materials affected by UV light with UV
shielding or reflective tape.
The AirBRIGHT™ Odor Absorber unit should be oriented so that the air flows past the
UV Light first then into the AirBRIGHT Odor Absorber.
6
Fig. 1. Supply Side installation. Airflow depicted by arrows.
M34597
FURNACE AIR HANDLER
7
Fig. 2. Return Side installation. Airflow depicted by arrows.
M34621
FURNACE
AIR HANDLER
8
Option 1
Internal Mounting
IMPORTANT
Turn off main power source before installation. Model information is
printed on the Power Unit cover.
1. Unfasten panel to gain access to mounting location
2. Determine the optimal position for placement of the Air Purifier.
3. If necessary, use a utility knife to
cut the insulation on the inside of
the duct.
4. Clean surface of glue, dust, etc.
M34659
9
M34689
5. Push the AirBRIGHT™ Odor Absorber into the base until the two tabs on the side
click into place.
6. Insert Snaplamp into base.
M34685
10
8. Place the magnetic bars on the base
directly on the clean metal surface.
M34661
7. Rotate the lamp handle clockwise
until it snaps in place.
9. Use foil tape to close the cut in the
insulation as needed.
M34660
11
10. Create a 5/8 (0.625) in. hole in the
duct and pass the cord through it. Clip
the bushing provided onto the cord at
a point close to the hole. Plug the hole
with the bushing.
M34601
M34602
12. Find a suitable location on the
outside of the duct-work near the
UV Lamp installation and apply the
warning/lamp replacement sticker.
13. Drill a 1/2 in. hole through the circle
on the sticker. Press the UV sight
glass into hole.
11. Secure access panel to the duct work.
12
Option 2
External Mounting for Metal Duct Applications
1. Use the gasket to mark the duct openings. Cut and remove openings, making sure
to cut 1/8-inch outside of the markings to create enough room for the product. If
using a hole saw to cut circular opening, use a 2-inch diameter bit.
M34604
13
M34687
2. Push the AirBRIGHT™ Odor Absorber
into the base until the two tabs on the
side click into place.
M34685
3. Remove one side of the backing from the gasket and stick
gasket on the ductwork so that the openings line up.
14
4. Peel away the other side of the backing on the gasket and insert AirBRIGHT™ into
the duct until the base sticks securely to the gasket.
5. Secure the base to the ductwork using self-tapping screws.
6. Insert lamp into base and turn handle clockwise to lock in place.
M34661
7. Find a suitable location on the outside of the duct-work near the UV Lamp
installation and apply the warning/lamp replacement sticker.
15
Option 3
Duct Board Mounting: For Duct Board Applications Only
1. Use the gasket to mark the duct openings. Cut and remove openings, making sure
to cut 1/8-inch outside of the markings to create enough room for the product. If
using a hole saw to cut circular opening, use a 2-inch diameter bit.
M34604
16
M34853
M34685
M34685
2. Push the AirBRIGHT™ Odor Absorber into the base until the two tabs on the side
click into place.
3. Bend metal tabs of duct board adapter
over the holes cut in the duct board.
17
M34852
4. Remove one side of the backing from the gasket
and stick gasket on the duct board adapter so
that the openings line up.
5. Peel away the other side of the backing on the gasket and
insert AirBRIGHT into the duct until the base sticks securely
to the gasket.
6. Secure the base to the ductwork using self tapping screws.
7. Insert lamp into base and turn handle clockwise to lock in
place.
8. Find a suitable location on the outside of the duct-work
near the UV Lamp installation and apply the warning/lamp
replacement sticker.
M34661
18
Power Supply Installation
• Find a suitable location for the power supply and mount using the self-tapping
screws.
• Use the wiring diagram on the next page to connect to power.
• When all the other components are properly installed connect the UV lamp cable
to the power supply cable.
M34663
ALIGN FLANGES
2.
1.
• Make sure the flanges are aligned
and then push the connectors
firmly together. A tight connection
ensures a proper water-resistant
seal. See image at right.
• Turn on the power and use the
lamp handle or sight glass to
confirm that the UV Lamp is
operating.
19
Power Supply Wiring
WARNINGS:
• Draws 16 VA, do load calculation to determine if a separate transformer is
needed.
• Systems with high 24 VAC loads may require the installation of a separate 24
VAC transformer to power the UV light.
• Always use a separate 24 VAC transformer with “communicating” air systems.
M34605
NOTE: IMPORTANT! MUST BE WIRED TO CONSTANT POWER. DO NOT CONNECT TO
BLOWER RELAY.
24 VAC
TRANSFORMER
BALLAST
24 VAC
COMMON
HOT
BLACK
RED
CONSTANT
110V
20
Maintenance
Note: Lamps should be replaced every year. UV lamps will continue to emit visible
light but lose germicidal effectiveness after approximately one year.
Changing UV Lamp
1. Disconnect the power to your heating and cooling system.
2. Unplug or turn off power to your UV System and allow the lamp to cool for at least
15 minutes.
3. Rotate the lamp handle counterclockwise, as shown below, and gently pull the
lamp handle to remove the lamp.
M34606
M34609
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80

Honeywell UV2400U1000 Guide d'installation

Taper
Guide d'installation
Ce manuel convient également à