ECOVACS DEEBOT T9 Le manuel du propriétaire

Instruction Manual/Bedienungsanleitung/Manual de instrucciones/

Manuel d'instructions/Manuale d'uso/Gebruiksaanwijzing/

Instrukcja obsługi/Руководство по эксплуатации

2

EN

Important Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical Appliance, basic

precautions should always be followed, including

the following:

READ ALL INSTRUCTIONS BEFORE

USING THIS APPLIANCE

SAVE THESE INSTRUCTIONS

1. This Appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they

have been given supervision or instruction

concerning use of the Appliance in a safe way

and understand the hazards involved. Children

shall not play with the Appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

2. Clear the area to be cleaned. Remove power

cords and small objects from the floor that

could entangle the Appliance. Tuck rug fringe

under the rug base, and lift items such as

curtains and tablecloths off the floor.

3. If there is a drop off in the cleaning area due

to a step or stairs, you should operate the

Appliance to ensure that it can detect the step

without falling over the edge. It may become

necessary to place a physical barrier at the

edge to keep the unit from falling. Make sure

the physical barrier is not a trip hazard.

4. Only use as described in this manual. Only

use attachments recommended or sold by the

manufacturer.

5. Please make sure your power supply source

voltage matches the power voltage marked on

the Auto-Empty Station.

6. For INDOOR household use ONLY. Do not

use the Appliance in outdoor, commercial or

industrial environments.

7. Use only the original rechargeable battery and

Auto-Empty Station provided with the Appliance

from the manufacturer. Non-rechargeable

batteries are prohibited. For battery information,

please refer to Specifications section.

8. Do not use without dust bin and/or filters in

place.

9. Do not operate the Appliance in an area where

there are lit candles or fragile objects.

10. Do not use in extremely hot or cold

3

EN

environments (below -5˚C/23˚F or above

40˚C/104˚F).

11. Keep hair, loose clothing, fingers, and all parts

of body away from any openings and moving

parts.

12. Do not operate the Appliance in a room where

an infant or child is sleeping.

13. Do not use Appliance on wet surfaces or

surfaces with standing water.

14. Do not allow the Appliance to pick up large

objects like stones, large pieces of paper or

any item that may clog the Appliance.

15. Do not use Appliance to pick up flammable

or combustible materials such as gasoline,

printer or copier toner, or use in areas where

they may be present.

16. Do not use Appliance to pick up anything that

is burning or smoking, such as cigarettes,

matches, hot ashes, or anything that could

cause a fire.

17. Do not put objects into the suction intake. Do

not use if the suction intake is blocked. Keep

the intake clear of dust, lint, hair, or anything

that may reduce air flow.

18. Take care not to damage the power cord. Do

not pull on or carry the Appliance or Auto-

Empty Station by the power cord, use the

power cord as a handle, close a door on the

power cord, or pull power cord around sharp

edges or corners. Do not run Appliance over

the power cord. Keep power cord away from

hot surfaces.

19. If the power cord is damaged, it must be

replaced by the manufacturer or its service

agent in order to avoid a hazard.

20. Do not use with a damaged power cord or

receptacle. Do not use the Appliance or Auto-

Empty Station if it is not working properly, has

been dropped, damaged, left outdoors, or

come in contact with water. It must be repaired

by the manufacturer or its service agent in

order to avoid a hazard.

21. Do not use with a damaged power cord or

receptacle. Do not use the Appliance or Auto-

Empty Station if it is not working properly, has

been dropped, damaged, left outdoors, or

come in contact with water. It must be repaired

by the manufacturer or its service agent in

order to avoid a hazard.

22. Turn OFF the power switch before cleaning or

maintaining the Appliance.

23. The plug must be removed from the receptacle

4

EN

before cleaning or maintaining the Auto-Empty

Station.

24. Remove the Appliance from the Auto-Empty

Station, and turn OFF the power switch to

the Appliance before removing the battery for

disposal of the Appliance.

25. The battery must be removed and discarded

according to local laws and regulations before

disposal of the Appliance.

26. Please dispose of used batteries according to

local laws and regulations.

27. Do not incinerate the Appliance even if it is

severely damaged. The batteries can explode

in a fire.

28. When not using the Auto-Empty Station for a

long period of time, please unplug it.

29. The Appliance must be used in accordance

with the directions in this Instruction Manual.

ECOVACS ROBOTICS cannot be held liable

or responsible for any damages or injuries

caused by improper use.

30. The robot contains batteries that are only

replaceable by skilled persons. To replace

the robot’s battery, please contact Customer

Service.

31. If the robot will not be used for a long time,

power OFF the robot for storage and unplug

the Auto-Empty Station.

32. WARNING: For the purposes of recharging

the battery, only use the detachable supply

unit CH1822 provided with the Appliance, or

CH1918 sold separately as an accessory.

To satisfy RF exposure requirements, a separation

distance of 20 cm or more should be maintained

between this device and persons during device

operation.

To ensure compliance, operations at closer than

this distance is not recommended. The antenna

used for this transmitter must not be co-located in

conjunction with any other antenna or transmitter.

5

EN

To disable Wi-Fi module on DEEBOT, power the

robot ON.

Place the robot on the Auto-Empty Station making

sure the Charging Contacts on DEEBOT and the

Auto-Empty Station Pins make a connection.

Press and hold the AUTO Mode Button on the

robot for 20 seconds until DEEBOT emits 3 beeps.

To enable Wi-Fi module on DEEBOT, power the

robot OFF and then power ON. The Wi- Fi module

is turned on when DEEBOT is restarted.

Correct Disposal of this Product

This marking indicates that this product should

not be disposed of with other household waste

throughout the EU. To prevent possible harm to the

environment or human health from uncontrolled

waste disposal, recycle it responsibly to promote

the sustainable reuse of material resources. To

recycle your used device, please use the return and

collection systems or contact the retailer where the

product was purchased. They can safely recycle this

product.

For EU Countries

Class II

Short-circuit-proof safety isolating

transformer

Switch mode power supply

For indoor use only

Direct current

Alternating current

For EU Declaration of Conformity information, visit

https://www.ecovacs.com/global/compliance

6

EN

Air Freshener Capsule

Main Ingredients: Ethylene/Vinyl Acetate

Copolymer, Fragrance

See manufacturing date, expiration date, and lot

number on pack.

*Each unit will last up to 60 days based on 1 hour

of use per day on ambient temperature conditions.

CAUTION:

USE ONLY AS DIRECTED. KEEP OUT OF REACH

OF CHILDREN AND PETS. EYE IRRITANT. Avoid

contact with eyes, skin, and clothing. In case of

contact with skin or eyes, wash immediately with

plenty of water for 15 minutes. If eye irritation

persists, consult a physician. Do not ingest. IF

SWALLOWED, do not induce vomitting; call

physician or poison control center immediately. DO

NOT PLACE NEAR HEAT OR OPEN FLAME. The

product is not to be used by persons with reduced

physical, sensory or mental capabilities. Used on

DEEBOT and for indoor air deodorization only. Do

not disassemble the capsule. Wash hands after

handling. Keep away from foodstuffs, beverages

and feed. Keep in a dry and well-ventilated place.

Dispose in accordance with local regulation.

7

EN

Package Contents

Robot Instruction ManualDocking Station

Side Brushes Disposable Mopping Pads

Note: Figures and illustrations are for reference only and may differ from actual

product appearance. Product design and specications are subject to changes

without notice.

OZMO Pro

Oscillating System

Air Freshener (Pre-installed) Air Freshener Capsule

Product Diagram

Robot

AUTO Mode Button

Top Cover

TrueMapping

Distance Sensor

Anti-collision Bumper

TrueDetect

3D Sensor

8

EN

Wi-Fi Status

Indicator

RESET Button

Dust Bin Handle

Release Button

Filter Net

Power Switch

Sponge Filter

High Efciency Filter

Multi-function

Cleaning Tool

Charging Contacts

Anti-drop Sensors

Air Freshener

(Pre-installed)

Main Brush

Release Button

Universal Wheel

Side Brushes

Anti-drop Sensors

Driving Wheels

Main Brush

Carpet Detection

Sensor

Bottom View

9

EN

Capsule Container

Docking Station

Docking Station Pins

Power Cord

Reservoir

Air Freshener

Disposable

Mopping Pad

Water Inlet

Reservoir

Release Button

OZMO Pro Oscillating System

Air Freshener (Pre-installed)

Notes Before Cleaning

Tidy up the area to be cleaned by

putting furniture, such as chairs, in

their proper place.

During the rst use, make sure each

room door is open to help DEEBOT

fully explore your house.

It may be necessary to place a

physical barrier at the edge of a drop

to stop the unit from falling over the

edge.

Put away objects including cables,

cloths and slippers, etc. on the oor

to improve the cleaning efciency.

Before using the product on a rug

with tasseled edges, please fold the

rug edges under.

Please do not stand in narrow

spaces, such as hallways, and make

sure not to block the Detection

Sensor.

10

EN

ECOVACS HOME App

To enjoy all available features, it is recommended to control your DEEBOT via

the ECOVACS HOME app.

Wi-Fi Indicator Light

Before you start, make sure that:

• Your mobile phone is connected to a Wi-Fi network.

• The 2.4GHz band wireless signal is enabled on your router.

• The Wi-Fi indicator light on DEEBOT is slowly ashing.

Slowly flashing

Disconnected to Wi-Fi or

waiting for Wi-Fi connection

Rapidly flashing Connecting to Wi-Fi

Solid Connected to Wi-Fi

Wi-Fi Connection

Before Wi-Fi setup, make sure DEEBOT, mobile phone, and Wi-Fi network

meet the following requirements.

DEEBOT and Mobile Phone Requirements

• DEEBOT is fully charged and the power switch of DEEBOT is turned on.

• Wi-Fi status light slowly ashes.

• Turn off mobile phone’s cellular data (you can turn it back on after setup).

Wi-Fi Network Requirements

• You are using a 2.4GHz or 2.4/5 GHz mixed network.

• Your router supports 802.11b/g/n and IPv4 protocol.

• Do not use a VPN (Virtual Private Network) or Proxy Server.

• Do not use a hidden network.

• WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.

• WEP EAP (Enterprise Authentication Protocol) is not supported.

• Use Wi-Fi channels 1-11 in North America and channels 1-13 outside North

America (refer to local regulatory agency).

• If you are using a network extender/repeater, the network name (SSID) and

password are the same as your primary network.

1

Operating DEEBOT

During the ﬁrst cleaning:

1.Please make sure to install Air Freshener to create a home map in

ECOVACS HOME App.

2.Please supervise DEEBOT and assist it should there be a problem.

Start

Install Air Freshener

Press

Click

11

EN

3

Pressing for 3 seconds to send DEEBOT back to the Docking Station.

2

Pause

Return to Charge

Note: The robot’s Control Panel stops glowing after the robot is paused for a

few minutes. Press the AUTO Mode Button on DEEBOT to wake up the robot.

OZMO Pro Oscillating System

Add Water

Note:

1.Install OZMO Pro Oscillating System for oor scrubbing.

2.With electric oscillating mopping up to 480 times per minute, OZMO Pro is

applicable for areas of highly concentrated dirt or dust.

3.Before installing OZMO Pro, please make sure the contacts are thoroughly dry.

4.Please avoid using OZMO Pro on the carpet.

1

*

To prolong the service life of OZMO Pro, it

is recommended to use puried water or

softened water.

*

Do not soak OZMO Pro in water.

Attach Disposable Mopping Pad

2

12

EN

3

Dry Contacts Thoroughly

4

Install OZMO Pro

5

Start Cleaning

Air Freshener

1

4

Install Air Freshener Capsule

2

3

Dry Contacts Thoroughly

Install Air Freshener

Enable Air Freshening via ECOVACS HOME App

Click

13

EN

To keep DEEBOT running at peak performance, perform maintenance tasks and replace parts with the following frequencies:

A multi-function Cleaning Tool is provided for easy maintenance. Handle with care, this cleaning tool has sharp edges.

Note: ECOVACS manufactures various replacement parts and ttings. Please contact Customer Service for more information on replacement parts.

Robot Part Maintenance Frequency Replacement Frequency

Disposable Mopping Pad After each use Replace after each use

Side Brush Once every 2 weeks Every 3-6 months

Main Brush Once per week Every 6-12 months

Sponge Filter/High Efciency Filter Once per week Every 3-6 months

TrueDetect 3D Sensor

Universal Wheel

Anti-Drop Sensors

Bumper

Charging Contacts

Docking Station Pins

Once per week /

Regular Maintenance

Before performing cleaning and maintenance tasks on DEEBOT, turn the robot OFF and unplug the Docking Station.

14

EN

Maintain OZMO Pro Oscillating

System

*

After DEEBOT nishes mopping,

please empty the reservoir.

*

Wipe OZMO Pro Oscillating System

with a clean, dry cloth. Do not soak

into water.

Remove OZMO Pro

Disposable Mopping Pad

Wipe OZMO Pro Clean

1

3

2

Maintain Dust Bin and Filters

3

1

2

15

EN

4

6

5

7

Maintain Main Brush and

Side Brushes

Main Brush

16

EN

Side Brushes

Maintain Other Components

Note: Before cleaning the robot’s Charging Contacts and Docking Station Pins,

turn the robot OFF and unplug the Docking Station. Wipe the components with a

clean, dry cloth. Avoid using cleaning sprays or detergents.

17

EN

Indicator Light

DEEBOT will tell you something is wrong with an indicator light and voice report. More detailed support is available through the ECOVACS HOME and online

website.

Indicator Light Scenario

AUTO Mode Button glows a solid WHITE.

The robot is cleaning.

The robot is paused while cleaning.

AUTO Mode Button ashes WHITE.

The robot is charging.

The robot is starting.

The robot is relocating.

AUTO Mode Button glows a solid RED. The robot has low battery.

AUTO Mode Button ashes RED. The robot has a problem.

18

EN

No. Malfunction Possible Causes Solutions

1 DEEBOT is not charging.

DEEBOT is not switched ON. Switch ON DEEBOT.

DEEBOT has not connected to the Docking Station.

Be sure that the robot’s Charging Contacts have connected to

the Docking Station Pins.

The Power Cord is not connected to the Docking Station.

Make sure the Power Cord is rmly connected to the Docking

Station.

The Docking Station is not connected to the power

supply.

Make sure the Docking Station is connected to the power

supply.

The battery is completely discharged. Please contact Customer Care for help.

2

DEEBOT cannot return to the

Docking Station.

The Docking Station is not correctly connected. Make sure the Docking Station is correctly connected.

The Docking Station is manually moved during the

cleaning.

It is suggested not to move the Docking Station during the

cleaning.

DEEBOT is paused for more than 90 minutes. It is suggested not to pause DEEBOT for more than 90 minutes.

DEEBOT did not start cleaning from the Docking Station. Make sure DEEBOT starts cleaning from the Docking Station.

3

DEEBOT gets stuck while

working and stops.

DEEBOT is tangled with something on the

oor (electrical wires, curtains, carpet fringing, etc.).

DEEBOT will try various ways to free itself. If it is unsuccessful,

manually remove the obstacles and restart.

DEEBOT might be stuck under furniture with an entrance

of similar height.

Please set a physical barrier, or set a Virtual Boundary in the

ECOVACS HOME App.

Troubleshooting

19

EN

No. Malfunction Possible Causes Solutions

4

DEEBOT returns to the Docking

Station before it has nished

cleaning.

Working time varies according to oor surface, room

complexity and the Cleaning Mode selected. When

the battery gets low, DEEBOT automatically switches

to Recharge Mode and returns to the Docking Station

to recharge itself.

Turn on Continuous Cleaning function in ECOVACS HOME App.

DEEBOT will automatically resume the uncompleted cleaning

cycle when Continuous Cleaning is enabled.

DEEBOT is unable to reach certain areas blocked by

furniture or barriers.

Tidy up the area to be cleaned by putting furniture and small

objects in their proper place.

The Docking Station is too distant from the center of

the house.

Please place the Docking Station against the wall of a central

room of the house.

5

DEEBOT does not clean

automatically at the scheduled

time.

Time Scheduling function is cancelled.

Program DEEBOT to clean at specic times using the ECOVACS

HOME App.

DEEBOT is switched OFF. Switch ON DEEBOT.

The robot’s battery is low.

Keep DEEBOT switched ON and connected to the Docking

Station to make sure it has a full battery to work at any time.

6

DEEBOT is stuck when cleaning

with OZMO Pro installed.

DEEBOT may have difculty climbing over obstacles

when using OZMO Pro.

Please assist DEEBOT if there is a problem.

20

EN

No. Malfunction Possible Causes Solutions

7

DEEBOT misses cleaning spots to

be cleaned, or repeats cleaning the

area cleaned.

The cleaning cycle is interfered by small objects or

barriers on the oor.

Remove power cords and small objects from the oor to ensure

cleaning efciency. DEEBOT will automatically clean the area

missed, please avoid moving DEEBOT manually or block the

path during the cleaning cycle.

DEEBOT is working on slippery polished oors. Make sure the oor wax is dried before DEEBOT starts cleaning.

DEEBOT is unable to reach certain areas blocked

by furniture or barriers.

Tidy up the area to be cleaned by putting furniture and small

objects in their proper place.

The TrueMapping Distance Sensor is blocked.

Remove the objects that are blocking the TrueMapping Distance

Sensor.

8

DEEBOT is not able to connect to

the home Wi-Fi network.

Incorrect home Wi-Fi username or password

entered.

Enter the correct home Wi-Fi username and password.

Incorrect App installed. Please download and install ECOVACS HOME App.

DEEBOT is not within range of your home Wi-Fi

signal.

Make sure DEEBOT is within range of your home Wi-Fi signal.

Network setup started before DEEBOT was ready.

Turn ON Power Switch. Press the RESET Button. DEEBOT is

ready for network setup when its Wi-Fi Indicator light ashes

slowly.

DEEBOT does not support 5 GHz Wi-Fi.

Make sure the robot has been connected with 2.4 GHz Wi-Fi

network.

9

DEEBOT does not clean the

whole area.

The cleaning area is not tidy.

Remove small objects from the oor and tidy up the cleaning

area before DEEBOT starts cleaning.

10

DEEBOT Side Brushes drop out of

place during use.

The Side Brushes are not correctly installed. Make sure the Side Brushes click into place when installing.

La page charge ...

ECOVACS DEEBOT T9 Le manuel du propriétaire

ECOVACS DEEBOT T9 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents