Nikon P-TACTICAL .223 Manuel utilisateur

Taper
Manuel utilisateur
1.5-4.5×20 / 3×32 / 3-9×40 / 4-12×40
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Instruction manual/Mode d'emploi
2
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Congratulations on your choice of a Nikon riescope. Your new scope is the nest example of Nikons rugged and durable construction and precision bright optics; important qualities for a serious shooter’s riescope.
Whether you use your scope for target shooting or for hunting, the procedure for mounting is identical. A set of high-quality steel mounting rings which have a standard diameter of 1 in. (25.4 mm) are required to mount
the scope. Follow the ring manufacturer’s instructions for mounting procedures. After mounting the scope on your rie, follow the procedures for reticle alignment.
SUPPLIED ITEM(S)
Body ························································· 1 piece
Eyepiece cap ············
Objective cap···········
································ 1 pair*
*Rubber band linked (This type connects the objective and eyepiece caps using a rubber band.)
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
WARNING:
IMPROPER MOUNTING OF YOUR NIKON SCOPE CAN CAUSE SERIOUS INJURY.
THUS IT IS IMPORTANT THAT YOUR NIKON SCOPE IS MOUNTED PROPERLY BEFORE USING. TO ENSURE PROPER MOUNTING OF YOUR NIKON SCOPE, PLEASE HAVE IT MOUNTED AND/OR CHECKED BY AN EXPERIENCED
GUNSMITH BEFORE USING.
THE USER ASSUMES ALL RESPONSIBILITY AND LIABILITY FOR HAVING THE SCOPE PROPERLY MOUNTED TO A FIREARM AND FOR USING THE SCOPE PROPERLY.
ALWAYS CHECK THE CONDITION OF YOUR SCOPE AND YOUR MOUNTING SYSTEM BEFORE USING YOUR FIREARM.
3
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Notice for customers in the State of California
WARNING: This product contains chemicals including Lead which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov.
When setting the reticle for shooting or hunting, you should determine your standard range and then adjust the reticle based upon that target distance. For targets which vary from that standard distance, according to
personal preference, you may simply adjust the position of the reticle in relation to your target, or you may wish to use the procedure for trajectory compensation.
We hope that you will enjoy your new Nikon Riescope for many years to come. Enjoy using it, and above all, always follow safe shooting procedures.
N.B. Export of the products* in this manual may be controlled under the laws and relatives of the exporting country. Appropriate export procedure, such as obtaining of export license, shall be required in case of export.
*Products: Hardware and its technical information (including software)
Caution
(1) Do NOT look at the sun through the riescope. It will permanently damage your eye. This precaution applies to all optical devices, such as cameras and binoculars.
(2) The riescope is eectively sealed against moisture and dust. You may use your scope safely either in the rain or in dusty climates. To preserve the appearance of the scope, we recommend that it be dried and
cleaned prior to storage. Use a soft cloth for cleaning metal surfaces and use photographic lens tissue to clean the scopes lenses.
4
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
2.5
4
3.5
3
9
6
5
7
8
Fig. 1-1
1. Nomenclature
1.5-4.5×20
1 Objective lens
2 Eyepiece lens
3 Elevation adjustment turret
4 Windage adjustment turret
5 Eyepiece adjustment
6 Power index
*
7 Power scale
*
8 Power selector ring
*
9 Diopter index dot
*
1.5-4.5×20, 3-9×40 and 4-12×40 only
3×32
3-9×40
4-12×40
Fig. 1-2
Fig. 1-3
5
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Objective Eyepiece
Letters a to d in the diagram above refer to lengths (a) to (d) shown in the Specifications table.
2. Specications
Model 1.5-4.5×20 3×32 3-9×40 4-12×40
Actual magnification (×) 1.5-4.5 3 3-9 4-12
Effective objective diameter (mm) 20 32 40 40
Exit pupil (mm) 13.3-4.4
*1
10.7 13.3-4.4
*1
10.0-3.3
*1
Eye relief (in.)/(mm) 3.5-3.5/88.9-88.9
*1
3.4/87 3.6-3.6/91.5-91.5
*1
3.7-3.7/94.0-94.0
*1
Tube diameter (in.)/(mm) 1/25.4 1/25.4 1/25.4 1/25.4
Objective outside diameter (in.)/(mm) 1/25.4 1.6/40.5 1.9/48.8 1.9/48.8
Eyepiece outside diameter (in.)/(mm) 1.7/44 1.6/41 1.7/44 1.7/44
Adjustment graduation 1 click: 1/4 MOA
*2
1 revolution: 20 MOA
*2
1 revolution: 80 clicks
1 click: 1/4 MOA
*2
1 revolution: 20 MOA
*2
1 revolution: 80 clicks
1 click: 1/4 MOA
*2
1 revolution: 20 MOA
*2
1 revolution: 80 clicks
1 click: 1/4 MOA
*2
1 revolution: 20 MOA
*2
1 revolution: 80 clicks
Max. internal adjustment (MOA)
*2
150 130 75 55
Parallax setting (yd.)/(m) 100/91.4 100/91.4 100/91.4 100/91.4
Field of view at 100 yd. (ft) 63.1-20.4
*1
35.6 33.5-11.5
*1
23.6-7.9
*1
Field of view at 100 m (m) 21.0-6.8
*1
11.9 11.2-3.8
*1
7.9-2.6
*1
Length (a) (in.)/(mm) 10.2/258.0 8.2/209.0 12.4/315 14.1/358
Mount length (b) (in.)/(mm)
2.9/73.6 1.2/29.6 2.0/50.6 2.5/63.5
Mount length (c) (in.)/(mm)
1.3/33.0 1.3/33.0 1.3/33.0 1.3/33.0
Mount length (d) (in.)/(mm)
2.1/53.0 1.1/28.3 2.1/53.0 2.1/53.0
Weight
(oz)/(g)
14.8/420 12.7/360 16.9/480 17.5/495
Structure
Waterproof (up to 3 ft 3 in. (1 m) for 10 minutes) and nitrogen gas purged
*1
(at minimum magnification)-(at maximum magnification)
*2
MOA = Minute of Angle
6
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
A
I
B
N
O
E
L
K
M
F
G
H
J
C
D
BDC 600 reticle (for 1.5-4.5×20 only)
Model 1.5-4.5×20
Reticle BDC 600
Magnication (×) 1.5 4.5
Reticle subtensions (cm at 100 metres/inches at 100 yards)
Unit (in.) (cm) (in.) (cm)
A 1.50 4.17 0.50 1.39
B 24.00 66.72 8.00 22.24
C 3.00 8.34 1.00 2.78
D 6.00 16.68 2.00 5.56
E 3.00 8.34 1.00 2.78
F 4.50 12.51 1.50 4.17
G 11.25 31.28 3.75 10.43
H 15.00 41.70 5.00 13.90
I 19.50 54.21 6.50 18.07
J 24.75 68.81 8.25 22.94
K 30.75 85.49 10.25 28.50
L 37.50 104.25 12.50 34.75
M 44.25 123.02 14.75 41.01
N 51.00 141.78 17.00 47.26
O 3.00 8.34 1.00 2.78
Reticle subtension chart
Letters A to O in the diagram above refer to the reticle subtensions of units A to O shown on the table to the right.
7
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
A
J
B
O
P
E
M
L
N
F
G
H
I
K
C
D
BDC 600 reticle (for 3-9×40 and 4-12×40)
Model 3-9×40 4-12×40
Reticle BDC 600 BDC 600
Magnication (×) 3 9 4 12
Reticle subtensions (cm at 100 metres/inches at 100 yards)
Unit (in.) (cm) (in.) (cm) (in.) (cm) (in.) (cm)
A 0.75 2.09 0.25 0.70 0.75 2.09 0.25 0.70
B 24.00 66.72 8.00 22.24 24.00 66.72 8.00 22.24
C 1.50 4.17 0.50 1.39 1.50 4.17 0.50 1.39
D 3.00 8.34 1.00 2.78 3.00 8.34 1.00 2.78
E 2.25 6.26 0.75 2.09 2.25 6.26 0.75 2.09
F 4.50 12.51 1.50 4.17 4.50 12.51 1.50 4.17
G 7.50 20.85 2.50 6.95 7.50 20.85 2.50 6.95
H 11.25 31.28 3.75 10.43 11.25 31.28 3.75 10.43
I 15.00 41.70 5.00 13.90 15.00 41.70 5.00 13.90
J 19.50 54.21 6.50 18.07 19.50 54.21 6.50 18.07
K 24.75 68.81 8.25 22.94 24.75 68.81 8.25 22.94
L 30.75 85.49 10.25 28.50 30.75 85.49 10.25 28.50
M 37.50 104.25 12.50 34.75 37.50 104.25 12.50 34.75
N 44.25 123.02 14.75 41.01 44.25 123.02 14.75 41.01
O 51.00 141.78 17.00 47.26 51.00 141.78 17.00 47.26
P 3.00 8.34 1.00 2.78 3.00 8.34 1.00 2.78
Letters A to P in the diagram above refer to the reticle subtensions of units A to P shown on the table to the right.
8
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
A
H
B
E
F
G
C
D
BDC Carbine reticle
Model 3×32
Reticle BDC Carbine
Magnication (×) 3
Reticle subtensions (cm at 100 metres/
inches at 100 yards)
Unit (in.) (cm)
A 1.00 2.78
B 24.00 66.72
C 1.00 2.78
D 3.40 9.45
E 5.50 15.29
F 14.25 39.62
G 20.00 55.60
H 3.00 8.34
Letters A to H in the diagram above refer to the reticle subtensions of units A to H shown on the table to the right.
9
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
3. Instructions
(1) Focusing
1 Look through the eyepiece with your eye positioned about 4 in. (10 cm) away from the eyepiece to see the BDC 600 reticle
(Fig. 3-1) or the BDC Carbine reticle (Fig. 3-2).
Be sure your eye is positioned with proper alignment and with proper eye relief, otherwise the view will “black out.
2 Point the objective end of the scope at the sky (do NOT point it at the sun) or at a plain unpatterned wall.
3 Turn the eyepiece adjustment counter-clockwise and then turn it clockwise until the reticle appears sharp.
Notice: Reticle images shown in this manual are representation only. Actual images may vary.
BDC 600 reticle
Fig. 3-1
BDC Carbine reticle
Fig. 3-2
10
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
(2) Magnication
The P-TACTICAL .223 riescopes have xed or variable magnication. For details, see “2. Specications”.
To change powers (1.5-4.5×20, 3-9×40 and 4-12×40 only), rotate the power selector ring until the desired magnication appears adjacent to the power index.
(3) Adjustment of the riescope
Sighting through the riescope, align the rie with your aiming point on the target and shoot a trial round. If the bullet does not hit the aiming point, adjust the elevation and windage adjustment turrets as follows:
If the bullet hits under the aiming point, turn the elevation adjustment turret (counter-clockwise) in the direction of the arrow marked “U” for up. If the bullet hits high, turn the elevation adjustment turret (clock-
wise) in the direction of the arrow marked “D” for down.
If the bullet hits to the right of the aiming point, turn the windage adjustment turret (clockwise) in the direction of the arrow marked “L for left. If the bullet hits to the left of the aiming point, turn the windage
adjustment turret (counter-clockwise) in the direction of the arrow marked “R” for right.
Note:
The windage and elevation scales of P-TACTICAL .223 riescopes are calibrated in divisions of 1/4 minute of angle (MOA) with a click at intervals of 1/4 minute of angle.
When adjusting the reticle to the point of aim, remember that 1 minute of angle equals approximately 1 in. (2.54 cm) at 100 yd. (91.44 m).
Therefore, if the impact point is 2 in. (5.08 cm) low and 1 in. (2.54 cm) right at 100 yd. (91.44 m) parallax setting, you should adjust 2 minutes of angle up and 1 minute of angle left.
In the case of 50 yd. (45.72 m) parallax setting, the adjusting value is 2×. In the case of 75 yd. (68.58 m) parallax setting, the adjusting value is 1.5×.
11
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
(4) Zero resetting of adjustment turret
The elevation adjustment and windage adjustment turrets have a retracting system. After the reticle has been adjusted to match the point of impact, pull up the elevation adjustment or windage adjustment turret
to disengage. The turret can now be turned freely. Align the zero number to the index line to set the zero setting, and then release the turret. The turret automatically retracts to the original position.
12
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Utilizing the BDC reticle
Thank you for choosing the Nikon BDC reticle riescope. The BDC reticle is designed to compensate for the trajectory of your rearm. Regardless of the particular style of BDC reticle you have, the position of the circles are
based upon an average trajectory for some of the more popular projectiles and cartridges on the market based upon the intended use of the scope itself.
Please note that the reticle is based upon ballistic information and may or may not meet the same results for you as there are many variables that come into play such as:
Actual Velocity (Ammunition manufactures information in regards to muzzle velocity may or may not match the velocity your rearm produces. The best way to determine the actual muzzle velocity for your rearm
is to use a chronograph).
Temperature
Humidity
Altitude
Barometric Pressure
Condition and inherent accuracy of the rearm
The mounting system and how true it positions the scope to the centerline of the bore
13
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
BDC 600 reticle
BDC 600 reticle
The BDC 600 reticle was designed specically for the AR platform rie in .223 Remington using a 55 grain polymer tipped bullet with a muzzle
velocity of 3240 fps. The reticle was designed for a 100 yard zero, with circles representing 200, 300, 400, 500 and 600 yards, with hash marks
in between the circles for hold points of 250
*
, 350, 450 and 550 yards as shown on the right.
Please note that your rearm may or may not match the information listed for bullet drop based upon the variables listed in this section.
What if your choice of round in your AR rie is the .308 Winchester? NO PROBLEM, just go to the Nikon Spot On website (nikonsportoptics.com/
Spoton) and you can match your exact cartridge to the reticle. In fact, we highly recommend that you check out the Spot On website as it will
provide exact yardages that each circle represents, providing unparalleled ballistic data for long range shooting.
*
The BDC 600 reticle for 1.5-4.5×20 does not have a hash mark representing 250 yards.
100 yd.
250 yd.
350 yd.
450 yd.
550 yd.
200 yd.
300 yd.
400 yd.
500 yd.
600 yd.
14
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
BDC Carbine reticle
BDC Carbine reticle
The BDC Carbine reticle was designed specically for compact AR platform ries in .223 Remington using a variety of ammunition and muzzle
velocities. We recommend using 50 grain to 62 grain polymer tipped bullets at muzzle velocities of 3000 fps +. The reticle is designed for a
200yard zero, with hash marks representing 400 and 600 yards, allowing you to quickly bracket targets at 300 and 500 yards respectively.
Please note that your rearm may or may not match the information listed for bullet drop based upon the variables listed in this section.
What if your choice of round in your AR rie is a 40 grain bullet at 3600 fps? NO PROBLEM, just go to the Nikon Spot On website (nikonsportop-
tics.com/Spoton) and you can match your exact cartridge to the reticle. In fact, we highly recommend that you check out the Spot On website as
it will provide exact yardages that each hash mark represents, providing unparalleled ballistic data for long range shooting.
200 yd.
400 yd.
600 yd.
15
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
nikonsportoptics.com/Spoton
The Spot On website has been designed to provide accurate information that matches the ballistics of whatever projectile you are shooting directly to the reticle.
Please note that you should verify that your set up matches the information provided in this manual or the Spot On program before venturing into the eld. The only way to truly verify the information is by actual shooting.
Again, the variables listed above may or may not aect the results.
Note: It is imperative that the reticle be level in relation to the rearm. If the reticle is canted, even just a few degrees, it can cause the shot to drift o the centerline of the point of aim. There are many commercial leveling
devices on the market, but the one that we nd to be the most accurate in leveling the reticle is a plum bob. Use a bubble level to make sure the rearm is level, then look through scope at an appropriately placed plumb
bob and align the reticle accordingly.
Please also note that all Nikon BDC reticles were originally designed to be used on the highest magnication. Since changing the magnication changes the position of the circles in relation to the target, the distances
listed along with each of the illustrations are at the highest magnication. The center crosshair does not change with magnication as it is placed in the optical center of the scope.
The benet of the Spot On program is that it calculates the distance that each circle represents at every magnication.
If you have further questions regarding the Spot On Technology please visit the website: http://spoton.nikonsportoptics.com/spoton/questions.html
Note:
Spot On is available only in the US and Canada.
16
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Maintenance
(1) Lens cleaning
To remove dirt or ngerprints, soak gauze or lens cleaning paper (silicone-free paper sold at camera retailers) with a small quantity of absolute alcohol (available from drugstores) and lightly wipe o the aected
areas. Wiping with a handkerchief or leather may damage the lens surface and is not recommended.
Dust may scratch the lens surface or corrode the lens.
Brush dust o using a soft oil-free brush.
(2) Scope exterior
Use a soft dry cloth to wipe o any dirt or ngerprints that might accumulate.
It is not necessary to oil the scopes surface.
(3) Windage/elevation adjustment turrets
These adjustment turrets are permanently lubricated. Do not attempt to lubricate them.
17
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
(4) Eyepiece adjustment
This adjustment is permanently lubricated. Do not attempt to lubricate it.
(5) Power selector ring (1.5-4.5×20, 3-9×40 and 4-12×40 only)
No lubrication is required for the power selector ring.
18
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Waterproof models:
The riescope is waterproof, and will suer no damage to the optical system if submerged or dropped in water to a maximum depth of 3 ft 3 in. (1 m) for up to 10 minutes.
The riescope oers the following advantages:
Can be used in conditions of high humidity, dust and rain without risk of damage.
Nitrogen-lled design makes it resistant to condensation and mold.
Observe the following precautions when using the riescope:
The riescope should not be operated nor held in running water.
Any moisture should be wiped o before adjusting movable parts (adjustment turret, eyepiece, etc.) of the riescope to prevent damage and for safety reasons.
To keep your riescope in optimal condition, Nikon Vision recommends regular servicing by an authorized dealer.
Specications and equipment are subject to change without any notice or obligation on the part of the manufacturer.
19
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Bravo pour votre choix : votre nouvelle lunette de visée Nikon est un parfait exemple de la robustesse, de la longévité et de la précision des instruments d’optique Nikon - des qualités importantes pour tout tireur sérieux.
Que vous utilisiez votre lunette pour le tir à la cible ou pour la chasse, la procédure de montage est la même. Un jeu de bagues de montage en acier de haute qualité d’un diamètre standard de 1pouce (25,4mm) est
nécessaire au montage de la lunette. Pour le montage, suivez les instructions du fabricant des bagues. Après avoir monté la lunette de visée sur votre fusil, réglez l’alignement du réticule (croisée de ls) comme suit.
ÉLÉMENTS FOURNIS
Boîtier ······················································· 1
Protecteur d’oculaire ·······
Capuchon d’objectif ········
························1paire*
*Reliés par une bande de caoutchouc (sur le modèle, le protecteur d’oculaire et le capuchon d’objectif sont reliés entre eux par une bande de caoutchouc.)
AVERTISSEMENT :
UN MONTAGE INCORRECT DE VOTRE LUNETTE DE VISÉE NIKON PEUT CAUSER DE GRAVES BLESSURES.
IL EST DONC IMPORTANT DE LA MONTER CORRECTEMENT AVANT L’UTILISATION. POUR VOUS ASSURER DU BON MONTAGE DE VOTRE LUNETTE DE VISÉE NIKON, VEUILLEZ LE FAIRE RÉALISER ET/OU VÉRIFIER PAR UN
ARMURIER EXPÉRIMENTÉ AVANT L’UTILISATION.
L’UTILISATEUR ACCEPTE TOUTE RESPONSABILITÉ CONCERNANT LE MONTAGE DE LA LUNETTE DE VISÉE SUR UNE ARME À FEU ET LA BONNE UTILISATION DE CETTE LUNETTE.
VÉRIFIEZ TOUJOURS L’ÉTAT DE VOTRE LUNETTE DE VISÉE ET DE VOTRE SYSTÈME DE MONTAGE AVANT D’UTILISER VOTRE ARME.
20
En
Fr
En
Fr
Ru
Se
Ru
Fi
Cz
Ru
Ru
Se
Ru
Fi
Cz
Pour régler le réticule pour le tir à la cible ou la chasse, vous devrez tout d’abord déterminer la portée standard; réglez ensuite le réticule sur la base de cette distance de cible. Pour des cibles qui débordent de cette distance
standard, selon vos préférences, vous pouvez régler simplement la position du réticule par rapport à la cible, ou bien eectuer une correction de trajectoire.
Nous espérons que votre nouvelle lunette de visée Nikon vous procurera de longues années de satisfaction. Protez-en, mais avant tout, respectez toujours les consignes de sécurité en matière de tir.
N.B.: l’exportation des produits* objets de ce manuel risque d’être sujette aux lois en vigueur dans le pays exportateur. La mise en œuvre d’un processus d’exportation adapté, comme l’obtention d’une licence d’expor-
tation, peut savérer nécessaire.
*Produits: matériel et informations techniques connexes (y compris le logiciel)
Précautions
(1) Ne regardez PAS le soleil par la lunette de visée. Vous vous abîmeriez la vue de façon irrémédiable. Cette précaution s’applique à tous les instruments d’optique, comme les appareils photo et les jumelles.
(2) La lunette de visée est étanche à l’humidité et la poussière. Vous pouvez l’utiliser en toute sécurité sous la pluie et dans les environnements poussiéreux. Pour conserver l’extérieur de la lunette en bon état, nous
vous recommandons de sécher et de nettoyer la lunette avant de la ranger. Utilisez un chion doux pour nettoyer les parties métalliques et utilisez des papiers pour objectif photo pour nettoyer les objectifs de
la lunette.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Nikon P-TACTICAL .223 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues