Greenlee 6000 Series Super Tugger Cable Pullers Manuel utilisateur

6000-Series

Super Tugger

®

Cable Pullers

Effective with Serial Code YF 2000 for 115 Volt Pullers

and Serial Code ACN for 220 Volt Pullers

INSTRUCTION MANUAL

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Español ............... 29

Français .............. 57

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

2

KEEP THIS MANUAL

Table of Contents Description

The Greenlee Super Tugger

®

cable puller is intended to

be used to pull cable through conduit and in tray. The

Super Tugger will develop 28.9 kN (6500 lb) of pulling

force. See a Greenlee catalog for sheaves, pulling

rope, and other cable pulling accessories rated for use

with the Super Tugger to create an entire cable pulling

system.

No single manual can provide instructions for every

cable pulling application. This manual contains general

information for pulling cable. Illustrations of some typical

setups are also provided.

Safety

Safety is essential in the use and maintenance of

Greenlee tools and equipment. This instruction manual

and any markings on the tools provide information for

avoiding hazards and unsafe practices related to use of

this tool. Observe all of the safety information provided.

Purpose of this Manual

This manual is intended to familiarize all personnel with

the safe operation and maintenance procedures for the

Greenlee 6000-Series Super Tugger

®

cable pullers.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no

charge at www.greenlee.com.

Description .................................................................... 2

Safety ............................................................................ 2

Purpose of this Manual ................................................. 2

Important Safety Instructions ..................................... 3-5

Grounding Instructions .................................................. 6

Identication .................................................................. 7

Specications ................................................................ 7

Cable Pulling Glossary .................................................. 8

Cable Pulling Principles ............................................ 9-17

Cable Pulling Systems ............................................... 9

Pulling Theory .......................................................... 10

Cable Pulling Forces ...........................................11-15

Tailing the Rope ....................................................... 16

Summary of Cable Pulling Principles....................... 17

Planning the Pull .......................................................... 17

Typical Setups ........................................................ 18-20

Setup and Operation .............................................. 21-22

Removing Cable .......................................................... 23

Dual Pulling ................................................................. 24

Maintenance ........................................................... 25-27

Troubleshooting ........................................................... 28

Exploded Views and Parts Lists ............................. 85-95

Wiring Diagrams ..................................................... 96-97

All specications are nominal and may change as design

improvements occur. Greenlee Textron Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

Super Tugger is a registered trademark of Textron Innovations Inc.

Mobilgrease is a registered trademark of Mobil Oil Corporation.

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning will

result in severe injury or death.

Do not operate the cable puller in

a hazardous environment. Hazards

include ammable liquids and gases.

Failure to observe this warning will

result in severe injury or death.

Electric shock hazard:

Disconnect the cable puller from the

power supply before servicing.

Failure to observe this warning could

result in severe injury or death.

Note: Keep all decals clean and legible, and replace

when necessary.

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

4

IMPORTANT SAFETY INFORMATION

Inspect all components of the cable

pulling system. Verify the maximum

load-bearing capacity or maximum

strength of all structural supports,

pulling system components and

anchoring systems before setting

up the puller. Any component that

cannot withstand the maximum cable

pulling forces may break and strike

nearby personnel with great force.

Failure to observe this warning could

result in severe injury or death.

Do not allow anything other than the

pulling rope to contact the capstan.

A grip, swivel, or other component

could break and strike nearby per-

sonnel with great force.

Failure to observe this warning could

result in severe injury or death.

Do not stand directly under a vertical

pull. Cable could fall suddenly

from the conduit, injuring nearby

personnel.

Failure to observe this warning could

result in severe injury or death.

Do not operate puller if the anti-reverse mechanism

is not working. If you do not hear the clicking of the

anti-reversing pawl when the capstan is rotating, shut

the puller off and have it repaired by an authorized

Greenlee service center.

Failure to observe this warning could result in severe

injury or death.

Locate the puller so that it is close to the conduit.

Rope, cable, or connectors can break under tension,

causing the rope to whip violently.

Failure to observe this warning can result in severe

injury or death.

An under-rated rope may break and whip violently.

Use a double-braided composite rope with the follow-

ing characteristics:

• Maximum Rated Capacity:

at least 28.9 kN (6500 lb)

• Average Breaking Strength:

at least 115.6 kN (26,000 lb)

Failure to observe this warning could result in severe

injury or death.

• Check the condition of the entire rope before use.

A worn or damaged rope can break under tension

and whip violently.

• Do not maintain a stationary rope on a rotating

capstan. The wear generated may cause the rope

to break under tension and whip violently.

Failure to observe these warnings could result in

severe injury or death.

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

5

IMPORTANT SAFETY INFORMATION

Attach the pulling rope to the cable with appropriate

types of connectors as described in this manual.

Select connectors with a maximum-rated capacity of

at least 28.9 kN (6500 lb). An under-rated connector

can break under tension.

Failure to observe this warning could result in severe

injury or death.

Keep hands away from the capstan.

Rope at the capstan can crush a

hand.

Failure to observe this warning could

result in severe injury or death.

Do not wrap rope around hands,

arms, waist, or other body parts.

Do not stand in spent coils or tailed

rope. Hold rope so that it may be

released quickly.

Failure to observe this warning could

result in severe injury or death.

Rope, cable, or a connecting device can break under

tension, causing the rope to whip violently.

• Do not allow any unnecessary personnel to remain

in the area during the pull.

• Do not allow any personnel to stand in line with the

pulling rope.

Failure to observe these warnings can result in severe

injury or death.

Do not allow the rope to become overlapped on the

capstan. If an overlap begins to develop, relax the

tailing force immediately and shut off the cable puller.

Failure to observe this warning could result in severe

injury or death.

Do not operate without chain guards

in place.

Failure to observe this warning could

result in severe injury or death.

Use this tool for manufacturer’s intended purpose

only. Do not use the cable puller as a hoist or winch.

• The cable puller cannot lower a load.

• The load may fall.

Failure to observe this warning could result in severe

injury or death.

Inspect puller and accessories before use. Replace

any worn or damaged components with Greenlee

replacement parts. A damaged or improperly assem-

bled item can break and strike nearby personnel with

great force.

Failure to observe this warning could result in severe

injury or death.

Entanglement hazard:

• Do not operate the cable puller while wearing

loose-tting clothing.

• Retain long hair.

Failure to observe these warnings could result in

severe injury or death.

Wear eye protection when using this

tool.

Failure to wear eye protection could

result in severe eye injury from ying

debris.

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

6

Grounding Instructions

120 Volt Model

Electric shock hazard.

• Do not modify the plug provided

with the tool.

• Connect this tool to a grounded

receptacle on a 20-amp GFCI-

protected circuit.

Failure to observe these warnings

could result in severe injury or death.

This tool must be grounded. In the event of a malfunc-

tion or breakdown, an electrical ground provides a path

of least resistance for the electric current. This path of

least resistance is intended to reduce the risk of electric

shock.

This tool’s electric cord has a grounding conductor and

a grounding plug as shown. Do not modify the plug.

Connect the plug to a corresponding receptacle that is

properly installed and grounded in accordance with all

national and local codes and ordinances. Do not use an

adapter.

20 Amp/125 Volt

Plug and Receptacle

220 Volt Model

Electric shock hazard.

• Do not modify the plug provided

with the tool.

• Connect this tool to a grounded

receptacle on a 10-amp GFCI-

protected circuit.

Failure to observe these warnings

could result in severe injury or death.

This tool must be grounded. In the event of a malfunc-

tion or breakdown, an electrical ground provides a path

of least resistance for the electric current. This path of

least resistance is intended to reduce the risk of electric

shock.

This tool’s electric cord has a grounding conductor and

a grounding plug as shown. Do not modify the plug.

Connect the plug to a corresponding receptacle that is

properly installed and grounded in accordance with all

national and local codes and ordinances. Do not use an

adapter.

10 Amp/250 Volt

Plug and Receptacle

ReceptaclePlug

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

7

Identiﬁcation

1

2

3

5

9

10

6

7

11

12

13

4

8

1. Entrapment Peg

2. Capstan Chain Guard

3. Handle

4. Guarded ON/OFF Switch and

Circuit Breaker

5. Motor

6. Motor Chain Guard

7. Force Gauge with ON/OFF Switch

8. Handle/Cleat

9. Right-Angle Idler Sheave

10. Tapered Capstan

11. Rope Ramp

12. Pivoting Capstan Arm

13. Positioning Peg

Speciﬁcations

Weight ...................................................... 41.7 kg (92 lb)

Dimensions:

Length ............................................. 52.7 cm (20-3/4")

Width ................................................ 57.2 cm (22-1/2")

Height ......................................................30.5 cm (12")

Power (120 Volt Model):

Voltage ................................................120 VAC, 60 Hz

Current ........................................................... 17 amps

Source .........................20 amp GFCI-protected circuit

Power (220 Volt Model):

Voltage ................................................220 VAC, 50 Hz

Current .......................................................... 7.5 amps

Source .........................15 amp GFCI-protected circuit

Maximum Pulling Force .........................28.9 kN (6500 lb)

Speed:

No Load ......................................5 m/min (16.5 ft/min)

8900 N (2000 lb) ..........................3.4 m/min (11 ft/min)

17.8 kN (4000 lb) ........................ 2.3 m/min (7.5 ft/min)

Duty Cycle:

0–22.2 kN (0–5000 lb) ............... Continuous operation

22.2–24.5 kN (5000–5500 lb)

(alarm will sound) .......... 15 minutes on/15 minutes off

24.5–28.9 kN (5500–6500 lb)

(alarm will sound) ............ 5 minutes on/15 minutes off

Pulling Rope:

Average Breaking Strength ..........115.6 kN (26,000 lb)

minimum

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

8

anchoring system

any item or group of items that keeps a cable pulling

component in place during the cable pull

capstan

the hollow cylinder of the cable puller that acts on the

pulling rope to generate pulling force

coefﬁcient of friction

the ratio that compares two amounts of force:

(1) the force needed to move an object over a surface

and (2) the force holding the object against the surface

This ratio is used to describe how the capstan and the

rope work together.

connector

any item, such as a wire grip, clevis, swivel, or pulling

grip, that connects the rope to the cable

direct line of pull

the areas next to the pulling rope and along its path;

this includes the areas in front of, in back of, and under-

neath the rope

maximum rated capacity

the amount of pulling tension that any component

can safely withstand, rated in kilonewtons (metric)

or pounds; the maximum rated capacity of every

component must meet or exceed the maximum pulling

force of the cable puller

Newton

a metric unit of force, equivalent to 0.225 pounds of

force

pipe adapter sheave

attaches to conduit for pulling or feeding cable

pulling grip

connects the rope to the cable; consists of a wire mesh

basket that slides over the cable and grips the insulation

Cable Pulling Glossary

pulling force

the amount of pulling tension developed by the cable

puller, rated in newtons (metric) or pounds; a cable

puller is usually described by the maximum pulling force

that it can develop

resultant force

any force that is produced when two or more forces act

on an object; applies to the sheaves of a cable pulling

system

rope ramp

a device that works with a tapered capstan; guides the

rope onto the capstan to prevent rope overlap

sheave

a pulley that changes the direction of the rope and cable

stored energy

the energy that accumulates in the pulling rope as it

stretches, described in newton-meters (metric) or

foot-pounds

support structure

any stationary object that a cable pulling system

component is anchored to, such as a concrete oor

(for the oor mount) or an I-beam (for a sheave)

tail

the portion of the rope that the operator applies force

to; this is the rope coming off of the capstan, and is not

under the tension of the pull

tailing the rope

the operator’s main function; this is the process of

applying force to the tail of the pulling rope—see the

complete explanation under Principles of Cable Pulling

wire grip

connects the rope to the cable; some use a set screw to

clamp onto the conductors of the cable

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

9

Cable Pulling Principles

Pulling cable is a complex process. This section of

the manual describes and explains four main topics of

pulling cable:

• each cable pulling system component

• how these components work together

• forces that are generated

• procedures for the cable puller operator to follow

While reading through this section of the manual, look

for components that are shaded in the illustrations. The

shading indicates components that are associated with

the text.

Greenlee strongly recommends that each member of

the cable pulling crew review this section of the manual

before each cable pull.

Cable Pulling Systems

Pulling cable requires a system of components. At a

minimum, a cable pulling system will include a cable

puller, a cable pulling rope, and connectors to join the

rope to the cable. Most systems will also include, but

are not limited to, a cable puller anchoring system,

pulling sheaves and sheave anchoring systems.

The cable puller has a maximum amount of pulling

force, which is the amount of pulling tension that it

develops. Every other component of the pulling system

has a maximum rated capacity, which is the amount

of pulling tension that it can withstand. The maximum

rated capacity of every component must meet or

exceed the cable puller’s maximum pulling force.

Typical Cable Pulling System

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

10

Cable Pulling Principles (cont’d)

Cable Pulling Theory Illustrated

Pulling Theory

This section introduces the main ideas involved with

pulling cable.

Pulling Resistance

The cable puller must overcome two types of resistance:

gravity and friction.

Gravity constantly exerts its force on the vertical

portions of the run. When the pulling force is relaxed,

gravity attempts to pull the cable downward. Friction

develops where the cable contacts the sheaves, conduit

and tray. Friction resists any movement, forward or

backward, and tends to hold the cables in place.

To accomplish a cable pull, the cable pulling system

must develop more force than the combination of

gravity and friction.

Generating Pulling Force

To generate pulling force, the capstan works as a

force multiplier. The operator exerts a small amount

of force on the rope. The cable puller multiplies this

and generates the pulling force.

This pulling force is applied to the rope, connectors,

and cable in order to accomplish the pull. The direc-

tion of force is changed, where necessary, with pulling

sheaves.

Gravity

Weight

of Cable

Conduit

Friction

Tailing

Force

Pulling Force

28.9 kN

(6500 lb)

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

11

Cable Pulling Principles (cont’d)

Pulling Force at the Cable Puller’s Anchoring System

Cable Pulling Forces

This section provides detailed explanations and illustra-

tions of the forces that are generated during the cable

pull. These explanations are based on the concepts

presented in the last section, Pulling Theory.

At the Cable Puller Anchoring System

The cable puller will exert its maximum pulling force on

cable puller’s anchoring system. It is extremely import-

ant the anchoring system can withstand this amount of

force. Refer to “Typical Setup: Floor Mount” for proper

setup or installation.

28.9 kN

(6500 lb)

Maximum

28.9 kN

(6500 lb)

Maximum

Pulling Force

28.9 kN

(6500 lb)

Maximum Pulling Force

at Anchoring System

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

12

Cable Pulling Principles (cont’d)

Cable Pulling Forces (cont’d)

At the Capstan

The capstan acts as a force multiplier. The operator

exerts a small amount of tension, or tailing force, on the

rope; the capstan multiplies this force to pull the cable.

The resultant force depends upon the number of times

the rope is wrapped around the capstan, as shown in

the formula below.

Pulling Force = Tailing Force x e

0.0175µø

Where: e = the natural logarithm, or 2.7183

µ = the coefcient of friction between the

rope and the capstan*

ø = the number of degrees of wrap of rope

around the capstan

* The average value for the coefcient of friction when

double-braided composite rope is pulled over a clean

dry capstan is 0.125.

The following table is based on the formula above.

The input, or tailing force, is constant at 44.5 N (10 lb).

Increasing the number of wraps increases

the pulling force.

Operator’s

TailingForce

Number of

Wraps of Rope

Approximate

PullingForce

44.5 N (10 lb)

1 93.4 N (21 lb)

2 213.5 N (48 lb)

3 474.9 N (106 lb)

4 1043.8 N (233 lb)

5 2293.7 N (512 lb)

6 5048.9 N (1127 lb)

7 11.1 kN (2478 lb)

This table shows how the capstan acts as a force

multiplier. Because the coefcient of friction depends

upon the condition of the rope and capstan, this formula

cannot determine an exact amount of pulling force.

The Capstan as a Force Multiplier

Pulling Force: 28.9 kN (6500 lb)

Tailing

Force

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

13

Cable Pulling Principles (cont’d)

Stored Energy

Cable Pulling Forces (cont’d)

At the Pulling Rope

The product of a force (f) moving through a distance

(d) is energy (f x d), and may be measured in newton-

meters or foot-pounds. Energy is stored in a rope when

the rope is stretched. This is similar to the way energy is

stored in a rubber band when it is stretched. Failure of

the rope or any other component of the pulling system

can cause a sudden uncontrolled release of the energy

stored in the rope.

For example, a 100-meter nylon rope with a 50,000

newton average breaking strength could stretch 40

meters and store 1,000,000 joules of energy. This is

enough energy to throw a 900-kilogram object, such as

a small automobile, 113 meters into the air.

A similar double-braided composite rope could store

approximately 300,000 joules of energy. This could

throw the same object only 34 meters into the air.

The double-braided composite rope stores much less

energy and has much less potential for injury if it were to

break.

Double-braided composite rope is the only type of rope

recommended for use with the Super Tugger cable

puller. Select a double-braided composite rope with an

average rated breaking strength of at least 115.6 kN

(26,000 lb).

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

14

Cable Pulling Principles (cont’d)

Cable Pulling Forces (cont’d)

At the Connectors

The connectors will be subjected to the cable puller’s

maximum pulling force.

Several types of rope connectors—clevises, swivels,

and rope-to-swivel connectors—are available. Follow

the instructions provided with each to provide a good

connection.

Two types of wire connectors—wire grips and pulling

grips—are available. The wire grip uses a set screw

to clamp onto the conductors of the cable. The pulling

grip consists of a wire mesh basket that slides over

the cable and grips the insulation.

When selecting a pulling grip, it is extremely important

to select a grip of the correct (1) type, (2) size, and (3)

maximum rated capacity.

1. Select the correct type based on the descriptions

of each type in the Greenlee catalog.

2. Measure the circumference of the wire bundle.

(To do this accurately, fasten a tie strap around the

bundle. Cut off and discard the tail. Then cut the tie

strap and measure its length.). Use the table pro-

vided to nd the correct size.

3. See the maximum rated capacities in the Greenlee

catalog.

Pulling Grip Size Table

Circumference Range Required Grip Diameter

inch mm inch mm

1.57–1.95 39.9–49.5 0.50–0.61 12.7–15.5

1.95–2.36 49.5–59.9 0.62–0.74 15.8–18.8

2.36–3.14 59.9–79.8 0.75–0.99 19.1–25.1

3.14–3.93 79.8–99.8 1.00–1.24 25.4–31.5

3.93–4.71 99.8–119.6 1.25–1.49 31.8–37.8

4.71–5.50 119.6–139.7 1.50–1.74 38.1–44.2

5.50–6.28 139.7–159.5 1.75–1.99 44.5–50.5

6.28–7.85 159.5–199.4 2.00–2.49 50.8–63.2

7.85–9.42 199.4–239.3 2.50–2.99 63.5–75.9

9.42–11.00 239.3–279.4 3.00–3.49 76.2–88.6

11.00–12.57 279.4–319.3 3.50–3.99 88.9–101.3

12.57–14.14 319.3–359.2 4.00–4.49 101.6–114.0

14.14–15.71 359.2–399.0 4.50–4.99 114.3–126.7

A Typical Grip Setup—Clevis and Wire Grip

A Typical Grip Setup—Swivel and Pulling Grip

Maximum

Pulling Force

28.9 kN

(6500 lb)

Maximum

Pulling Force

28.9 kN

(6500 lb)

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

15

Cable Pulling Principles (cont’d)

Typical Resultant Force at Sheave

Cable Pulling Forces (cont’d)

At the Sheaves

Sheaves are used to change the direction of the pull.

A change in direction creates a new resultant force

that may be greater than the cable puller’s maximum

pulling force. This new resultant force exerts itself on the

sheaves, sheave anchoring system, and support struc-

tures illustrated.

The resultant amount of force depends on the angle of

the change in direction. A brief table is provided here;

for more details, see IM 1363 (99929988).

Resultant Force Table for the Super Tugger

(28.9 kN or 6500 lb Maximum Pulling Force)

Illustration

Angle of Change

in Direction

R

180° 0 (0)

150° 15 (3380)

135° 22.3 (5005)

120° 28.9 (6500)

90° 40.8 (9165)

60° 50.0 (11,245)

45° 53.5 (12,025)

30° 55.8 (12,545)

0° 57.8 (13,000)

Resultant Force =

22.3 kN (5005 lb)

135°

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

16

Cable Pulling Principles (cont’d)

Tailing the Rope

The rope must be pulled off of the capstan as the pull

progresses. The rope that has left the capstan is the

“tail.” The process of pulling the rope off of the capstan

is called tailing the rope.

The resistance of the cable varies throughout the dura-

tion of the cable pull. Changes in resistance are due to

characteristics of the rope, changes in conduit direction,

and changes in the amount of friction. The “feel” of the

rope provides this information about the pull. This is

called tactile feedback. Adjust the tailing force as neces-

sary to compensate for these changes.

Control of the Pull

Decreasing the tailing force will decrease the pulling

force, until the rope slips on the capstan and the pull

stops. This provides a high level of control over the

progress of the cable pull.

Do not allow the rope to slip on the capstan for more

than a few moments. If it becomes necessary to com-

pletely stop a pull, shut off the puller and maintain

enough tailing force to hold cable in place. Tie the rope

off to hold it in place. Use the rope tie-off to hold it in

place.

Amount of Tailing Force

While the rope and cable are under tension, it is import-

ant to maintain the proper amount of tailing force.

Too little tailing force will allow the rope to slip on the

capstan. This will build up excessive heat and acceler-

ate rope wear, increasing the possibility of breaking the

rope.

The proper amount of tailing force will stop the rope

from slipping on the capstan and produce a sufcient

amount of pulling force to pull in the rope and cable.

Too much tailing force is any amount more than is nec-

essary to stop the rope from slipping on the capstan.

Excessive tailing force will not increase the pulling force

or pulling speed.

Number of Wraps of Rope Around the Capstan

An experienced operator should choose the number

times the rope is wrapped around the capstan.

The proper number of wraps allows the operator to

control the progress of the pull with a comfortable

amount of effort.

Using too few wraps requires a large tailing force to

accomplish the pull. Using too few wraps also makes

the rope more likely to slip on the capstan. This builds

up heat and accelerates rope wear.

Using too many wraps causes the rope to grab the

capstan tighter. This accelerates rope wear, wastes

power, and increases the possibility of a rope overlap.

Using too many wraps also reduces tactile feedback, so

you receive less information about the pull. You cannot

quickly relax the tailing force when there are too many

wraps.

If the rope becomes difcult to tail, add another wrap

of rope. Turn off the puller and release all of the tension

in the rope. Add a wrap and resume pulling. Be aware,

however, that some pulls will require tension to hold

the cables in place. In these cases, do not attempt to

release all of the tension and add a wrap of rope. You

will need to anticipate the number of wraps before start-

ing the pull.

Preventing Rope Overlap

Do not allow the rope to become overlapped on the

capstan during a pull.

A rope overlap will make it will impossible to continue or

back out of the pull.

If the rope becomes overlapped, you will lose control

of the pull —the rope will advance with no tailing force

and will not feed off of the capstan. The capstan will not

allow you to reverse the direction of the rope, so you

cannot back out of an overlap.

Set up the puller properly. The rope ramp and tapered

capstan are intended to prevent rope overlap. See the

instructions in the Operation section of this manual.

Every wrap of the rope must remain in direct contact

with the capstan. During the pull, take great care to

prevent the incoming rope from riding up and overlap-

ping the next wrap. If an overlap begins to develop,

immediately relax the tailing force on the rope so that

the rope can feed back toward the conduit or tray.

When the rope resumes its normal path, apply tailing

force and continue the pull.

There is no suggested remedy for a rope overlap.

Do not allow the rope to overlap!

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

17

Cable Pulling Principles (cont’d)

Summary of Cable Pulling Principles

• A cable pulling system consists of many components

that work together to accomplish a pull.

• The cable puller is rated by its maximum pulling force;

every other component is rated by its maximum rated

capacity. The maximum rated capacity of every com-

ponent must meet or exceed the maximum pulling

force of the cable puller.

• The cable puller must overcome two types of resis-

tance: gravity and friction. The puller’s capstan, the

pulling rope, and the operator tailing the rope work

together to produce pulling force.

• The cable puller exerts force on every component

of the cable pulling system, including the anchoring

systems and the support structures.

• Energy is stored in a rope when the load causes

the rope to stretch. Failure of the rope or any other

component can cause a sudden release of energy.

Replace any rope that is worn or damaged.

• Carefully select the number or wraps of rope around

the capstan before starting the pull.

• Control the pull by tailing the rope. Be familiar with the

interaction of the rope and capstan.

• Do not allow a rope overlap to develop.

• Pull in a direction that will require the lowest amount

of pulling force.

• Plan several shorter pulls rather than fewer longer

pulls.

• Locate the puller as close to the end of the conduit

as possible to minimize the amount of exposed rope

under tension.

• Place each component so that the pulling forces are

used effectively.

• Select an anchoring system: adapter sheaves, which

are preferred, or the oor mount.

• Verify that each component has the proper load

rating.

• Inspect the structural supports. Verify that they have

enough strength to withstand the maximum forces

that may be generated.

Planning the Pull

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

18

Typical Setups—using 11147 Adapter Package

Setups are shown without force gauge. Place the force gauge so the operator has an unobstructed view

of the meter and quick access to its ON/OFF switch.

Pulling Horizontally in Manhole

Using Two Booms, Nose Unit,

Elbow Unit and Slip-in Coupler

Pulling Horizontally in Manhole

Using Two Booms, Nose Unit,

Elbow Unit and Slip-in Coupler

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

19

Typical Setups—using 11147 Adapter Package (cont’d)

Setups are shown without force gauge. Place the force gauge so the operator has an unobstructed view

of the meter and quick access to its ON/OFF switch.

Pulling Up Using One Boom,

Nose Unit and Slip-in Coupler

Pulling Up Using Two Booms, Nose Unit,

Elbow Unit and Slip-in Coupler

6000-Series Super Tugger

®

Cable Pullers

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

20

Typical Setups (cont’d)

Setups are shown without force gauge. Place the force gauge so the operator has an unobstructed view

of the meter and quick access to its ON/OFF switch.

Generator

UNOCCUPIED MANHOLE UNOCCUPIED MANHOLE

UNOCCUPIED MANHOLEABOVE GROUND

Using a Manhole Sheave Using Feeding Sheaves in Manholes

Using a Floor Mount

La page charge ...

Greenlee 6000 Series Super Tugger Cable Pullers Manuel utilisateur

Ce manuel convient également à

Greenlee 6000 Series Super Tugger Cable Pullers Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents