KitchenAid KIRD801VSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KIRD801VSS0

Taper: Le manuel du propriétaire

Ce manuel convient également à

Kitchen_kid _

30" (76.2 CM) AND 36" (91.4 CM)

RETRACTABLE (POP-UP) DOWNDRAFT VENT

SYSTEM

SYSTEME DE VENTILATION RETRACTABLE

(CLAPET) DE 30"(76,2 CM) ET 36"(91,4 CM) -

ASPIRATION PAR LEBAS

Table of Contents/Table des matieres ............................................................................. 2

iMPORTANT: READ AND SAVE THESE iNSTRUCTiONS.

FOR RESiDENTiAL USE ONLY.

iMPORTANT : LIRE ET CONSERVER CES iNSTRUCTiONS.

POUR UTILISATION RESIDENTIELLE UNIQUEMENT.

W10187117B

TABLEOF CONTENTS

VENT SYSTEM SAFETY ................................................................. 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 7

Venting Requirements .................................................................. 7

INSTALLATION INSTRUCTIONS

INTERIOR-MOUNTED VENT MOTOR .......................................... 8

Venting Methods - Interior Mounted Vent Motor Only ................ 8

Install Vent System ....................................................................... 9

Complete Installation ................................................................. 13

Make Electrical Connections ..................................................... 13

Check Operation ........................................................................ 14

INSTALLATION INSTRUCTIONS

EXTERIOR-MOUNTED VENT MOTOR ....................................... 15

Venting Methods ........................................................................ 15

Install Vent System ..................................................................... 16

Electrical Connection ................................................................. 17

Complete Installation ................................................................. 18

VENT SYSTEM USE ..................................................................... 19

Operating Downdraft Vent ......................................................... 19

VENT SYSTEM CARE .................................................................. 19

Surface of Downdraft Vent ......................................................... 19

Filters .......................................................................................... 19

WIRING DIAGRAM ....................................................................... 20

ASSISTANCE OR SERVICE ......................................................... 21

WAR RANTY .................................................................................. 22

TABLE DES MATIERES

SECURITE DU SYSTEME DE VENTILATION ............................ 23

EXIGENCES D'INSTALLATION ................................................... 25

Outillage et pieces ...................................................................... 25

Exigences d'emplacement ......................................................... 25

Specifications electriques .......................................................... 28

Exigences concernant I'evacuation ........................................... 28

INSTRUCTIONS D'INSTALLATION

VENTILATEUR MONTE .&L'INTERIEUR .................................... 29

M6thodes d'extraction - Seulement pour un

ventilateur monte a I'interieur ..................................................... 29

Installation du systeme d'extraction .......................................... 30

Achever I'installation .................................................................. 34

Raccordements electriques ....................................................... 34

Contr61e du fonctionnement ...................................................... 35

INSTRUCTIONS D'INSTALLATION

VENTILATEUR MONTE .&L'EXTERIEUR ................................... 36

M6thodes d'extraction ............................................................... 36

Installation du systeme d'extraction .......................................... 37

Raccordement electrique ........................................................... 38

Achever I'installation .................................................................. 39

UTILISATION DU SYSTF:ME D'EXTRACTION ........................... 40

Utilisation du systeme d'extraction ............................................ 40

ENTRETIEN DU SYSTF:ME .......................................................... 40

Surface de I'appareil .................................................................. 40

Filtres .......................................................................................... 40

SCHI_MA DE C.&,BLAGE............................................................... 41

ASSISTANCE OU SERVICE ......................................................... 42

GARANTIE ..................................................................................... 43

VENT SYSTEM SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

m Use this unit only in the manner intended by the

manufacturer. Ifyou have questions, contact the

manufacturer.

m Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

m Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

m Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

m When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

m Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

m Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

[] Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

[] Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

[] Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

[] SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. Ifthe flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

[] NEVER PICK UP A FLAMING PAN - you may be burned.

[] DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

[] Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Parts Needed

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed

• Jigsaw or keyhole saw

• Drill

• 1/8"(3 mm) drill bit for pilot holes

• Pencil

• Two UL listed or CSA approved 1/2"(12.7 mm) conduit

connectors (Three are required if the exterior-mounted vent

motor is used.)

• Wall cap for interior-mounted motor (1)

• Vent system

• Home power supply cable

• Wiring cable for optional remote blower kit

• UL listed wire connectors (4)

• Tape measure or ruler

• Flat-blade screwdriver

• Phillips screwdriver

• 3/8"(9.5 mm) nut driver or ratchet

• Level

• Pliers

• Metal snips

• Wire stripper or utility knife

• Caulking gun and weatherproof caulking compound

• Vent clamps

Parts Supplied

C E

A. Top trim (1)

B.End caps (2)

C. Overcounter support brackets (2)

D. Lower support legs (2)

E. Undercounter mounting brackets (2)

Other Parts Supplied

• Bag of fasteners (1)

• Metal cover (1)

• Optional support and 2 screws (36" [91.4 cm] models only)

• 6" diameter backdraft damper

NOTE: Downdraft vent is installed directly behind the cooktop.

Install the downdraft vent first, then install the cooktop.

IMPORTANT: Observe all governing codes and ordinances.

• Have a qualified technician install the downdraft vent. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial rating plate. The model/serial

rating plate is located on the front of the downdraft vent

above the terminal box cover.

• Downdraft vent location should be away from strong draft

areas, such as windows, doors, and strong heating vents or

fans.

• Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance.

• Consult the cooktop manufacturer installation instructions

before making any cutouts.

Check that the downdraft vent and cooktop location will

clear the cabinet walls, backsplash, and rear wall studs

inside the cabinet.

Check for the minimum distance between the front edge

of the countertop and the front edge of the cooktop. The

minimum horizontal distance between the overhead

cabinets is the same as the width of the installed

downdraft vent.

• All openings in ceiling and wall where the downdraft vent will

be installed must be sealed.

• Grounded electrical outlet is required. See "Electrical

Requirements" section.

• When installing the downdraft vent, the cabinet drawer will

need to be removed and the drawer front installed

permanently to the cabinet.

Cabinet Construction:

Downdraft vent is designed for use in a cabinet with a depth of

24" (61 cm). Some installations require a countertop deeper than

25" (63.5 cm). See the Countertop Cutout Dimensions section.

The maximum depth of the overhead cabinet is 13" (33 cm).

Overhead cabinets installed at either side of the downdraft vent

must be 18" (45.7 cm) above the cooking surface.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A*, or latest edition, or with local

codes.

Product Dimensions

Interior-mounted blower motor model

_ Top trim widths:

30V4" (76.8 cm) for 30" (76.2 cm) vent

36V4" (92.1 cm) for 36" (91.4 cm) vent

Exterior-mounted blower motor model -

used with Part Number KPEC992M

13V2" (34.3 cm)

retractable

vent height

27" (68.6 cm) for 30" (76.2 cm) vent

33" (83.8 cm) for 36" (91.4 m

Terminal box cover

13" (33.0 cm)

11/2" (3.8 cm)

(0.95 cm)

283/4"

(73.0 cm)

6" (15.2 cm)

diameter

vent collar

(23.5 cm)

Cabinet Dimensions

Interior-mounted blower motor model Exterior-mounted blower motor model

A= 1/2"(12.7 ram)

minimum

1/2"(12.7 ram)

minimum

21%6"

(54.1 cm)

All cutouts are

for 6" (15.2 cm)

diameter vent

system.

NOTES:

Locate power

supply junction

box aflower

left hand

rear corner

of the cabinet.

Centerline of cooktop cutout

See cooktop manufacturer's instructions for cooktop cutout

depth and width.

Use dimensions for vent system cutout location that applies

to your installation.

Interior mounted blower systems connect with 6" (15.2 cm)

round vent. The cutout locations for this vent system will

depend on your specific installation.

NOTES:

Locate power

supply junction

pox afJower

left hand

rear corner

of the cabinet.

See cooktop manufacturer's instructions for cooktop cutout

depth and width.

Exterior-mounted blower systems connect with 10" (25.4 cm)

round vent. The cutout locations for this vent system will

depend upon your specific installation.

Countertop Cutout Dimensions

IMPORTANT: Countertops with a bullnosed front edge are not recommended for these installations.

• Some models require a countertop deeper than 25" (63.5 cm); see the following Countertop Cutout Dimensions section.

• To avoid mistakes, it is recommended that the cooktop and vent cutouts be drawn on the countertop before making any cutouts.

• See Cooktop Installation Instructions for complete cutout dimensions, location dimensions and installation details.

B C ---a_

A ....................................|

A. Downdraft vent

B. Cooktop

C. Measurement of cooktop rear overhang.

D. D = Measurement of eooktop rear overhang (C) +

11_,, [46.2 mm] (E)

E. 11_" (46.2 mm)

F. 7/2"(12.7 mm) minimum

G. ¼" (6.4 mm) minimum

H. Countertop and backsplash

I. 7/2"(12. 7 mm) minimum

Countertop Cutout Dimensions

A. 7/2"(12.7 mm) minimum to backsplash or

rear wall

B. _" (19.1 mm) maximum backsplash depth

C. 27½" (69.9 cm) on 30" (76.2 cm) models

33_" (85.9 cm) on 36" (91.4 cm) models

D. D = Measurement of cooktop rear overhang

+ 11_,, (46.2 mm)

/iii¸¸ L° i...... .................................

i ts

IMPORTANT: Observe all governing codes and ordinances. Save

Installation Instructions for electrical inspector's use.

It is the customer's responsibility to contact a qualified electrical

installer, and to ensure that the electrical installation is adequate

and in conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local

codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• This fan is suitable for use with solid state speed controls.

• A 120 Volt, 60 Hz., AC only 15-amp fused, electrical circuit is

required.

• Check with a qualified electrician if you are not sure the

downdraft vent is properly grounded.

• The downdraft vent must be connected with copper wire

only.

• The downdraft vent should be connected directly to the

circuit breaker (or fused disconnect) box through flexible

armored or nonmetallic sheathed copper cable. Allow some

slack in the cable so the downdraft vent can be moved if

servicing is ever necessary.

• Wire sizes (copper wire only) and connections must conform

with the rating of the appliance as specified on the model/

serial rating plate located on the front of the downdraft vent

above the wiring box cover.

• Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

• Two UL listed or CSA approved 1/2"(12.7 mm) conduit

connectors (Three are required if the exterior-mounted vent

motor is used.)

• A wiring diagram is located on the downdraft vent base

above the power control board cover.

IMPORTANT: Make sure there is proper clearance within the wall

or floor before making exhaust vent cutouts.

• Use heavy (rigid) metal vent.

• Venting system must terminate to the outside.

• Do not terminate the vent system in an attic or other enclosed

area.

• Do not use 4" (10.2 cm) laundry-type wall caps.

• Do not install 2 elbows together.

• Do not use plastic or metal foil vent.

• The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

• Use no more than three 90° elbows

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than one elbow is used.

• Use clamps to seal all joints in the vent system.

• Use caulking tape to seal the exterior wall or floor opening

around cap.

• Do not cut joist or stud. Ifvent cutout falls over a joist or stud,

a supporting frame must be constructed.

Flexible metal vent is not recommended. If it is used, calculate

each foot of flexible vent as 2 ft (0.6 m) of rigid metal vent.

Flexible elbows count twice as much as standard elbows.

Recommended vent system length:

For either interior-mounted or exterior-mounted blower

installations, the vent system length should not exceed the

maximum lengths listed in the Maximum Length of Vent System

chart. See "Calculating Vent System Length" in the "Venting

Methods - Interior Mounted Vent Motor Only" section.

INSTALLATION INSTRUCTIONS

INTERIOR-MOUNTED VENT MOTOR

_A_ _ _T _1_ _ _ _'_'"__',_,_uY_ _,'__:_:t1_ ¸¸'_¸_¸'......_¸_'¢¸'¸'¸_¸t_¸

Determine which venting method is best for your application. Island Location

Vent system can terminate through either the wall or floor. Vent system installed under a concrete slab using Pro

Island location sewer pipe.

A.Down vent K

Built-in cabinet locations

.... II

I) I............

II II .....D

C.Left vent

D.Right vent

A. Down vent

B. Rear vent

........<ii::........

/ ii

C E

d I

A. Wall cap

B. 6" (15.2 cm) round metal vent

C. 16" (40.6 cm) maximum

D. 6" (15.2 cm) round PVC sewer pipe

E. 6" (15.2 cm) round metal vent

F. 6" (15.2 cm) round PVC coupling

G. Concrete slab

H. 6" (15.2 cm) round PVC sewer pipe

I. 6" (15.2 cm) round 90 ° PVC sewer pipe elbow

J. Tightly pack gravel or sand completely around pipe.

K. 6" (15.2 cm) round 90 ° PVC sewer pipe elbow

L. 6" (15.2 cm) round PVC coupling

M. 12" (30.5 cm) minimum

Calculating Vent System Length

It is recommended that you use round vent instead of rectangular

vent, especially if elbows are required. If rectangular vent is

required, it should be transitioned to 6" (15.2 cm) round vent as

soon as possible.

Maximum Length of Vent System

Vent Length

6" (15.2 cm) round 35 ft (8.9 m)

31/4'' x 10" (8.3 cm x 25.4 cm) 35 ft (8.9 m)

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

6" (15.2 cm) 0.0 ft

wall cap (0.0 m)

31/4'' x 10" (8.3 cm x 25.4 cm) 4.5 ft

to 6" (15.2 cm) transition (1.4 m)

6" (15.2 cm) to 31/4'' x 10" 1 ft

(8.3 cm x 25.4 cm) transition (0.3 m)

31/4"x 10" (8.3 cm x 25.4 cm) 5.0 ft

to 6" (15.2 cm) 90° elbow (1.5 m)

transition

6" (15.2 cm) to 31A'' x 10" 5.0 ft

(8.3 cm x 25.4 cm) 90° elbow (1.5 m)

transition

Example Vent System

A. Blower motor

B. Transition

C. 90 ° elbows

D. 6" backdraft damper (suppfied)

The following example falls within the maximum vent length of

35 ft (8.9 m).

2 - 90° elbow

1 - wall cap

8 ft (2.4 m) straight

Transition

Length of 6" (15.2 cm)

system

= 10.0 ft (3 m)

= 0.0 ft (0.0 m)

= 8.0 ft (2.4 m)

= 4.5 ft (1.4 cm)

= 22.5 ft (6.8 m)

Excessive Weight Hazard

Use two or more people to move and install

downdraft vent.

Failure to do so can result in back or other injury.

1. Place cardboard or similar material on top of a flat surface

where you can easily assemble the downdraft vent systm.

2. Remove parts packages, downdraft vent and blower box

from the carton.

3. Remove all shipping materials, tape and film from the

downdraft vent and blower box.

4. Remove screws from each side of the vent. Attach the left

and right side overcounter support brackets to the downdraft

vent and push up to align the screw holes. Use screws to

secure the brackets.

_ A

A. Qvercounter support bracket

B.Blower motor box

C. Qvercounter support bracket screw

Attach the left and right side end caps to the downdraft vent.

Place the end cap upon the overcounter support, slide the

tab into the slot and snap into place over the the plastic tabs.

A. End cap

6. Attach support legs to the side of the downdraft vent with A

2 screws in each leg. Do not tighten screws. ........

A. Blower motor box

B. Support leg

7. Using 2 or more people, insert the downdraft vent into the

countertop cutout. Check that downdraft vent is parallel to

side of cutout and that mounting brackets overlap

countertop.

8. Move support legs down against cabinet floor. Place a level

against the front of the downdraft vent base and adjust until

downdraft vent is level vertically. Use a pencil to mark the top

of each leg on the downdraft vent and the location of the

support leg mounting holes on the cabinet floor.

A. Level

B. Mark locations.

9. Remove downdraft vent from cutout. Drill starter holes at

each mounting screw location on the cabinet floor. Align top

of legs with pencil marks on the face of the downdraft vent.

Tighten screws in legs.

Determine which direction is best for your installation.

When installed in a cabinet, vent system can exhaust through the

bottom, right, left or rear of the cabinet.

Bottom venting:

Downdraft vent is shipped with blower in down venting

position so no modification is required. Go to Step 9.

Left or right venting:

1. Loosen the 2 hex/slotted head screws that attach the top

bracket that secures the motor to the vent box enough to

slide the bracket into the "Z" slots. This will move the bracket

away from the top mounting lip of the blower box and allow it

to tilt away from the vent box panel.

A. Bracket with "Z" slots

B.Hex/slotted head screws (2)

Lift up the blower box from the bottom mounting channel.

A. Blower box

B. Bottom mounting channel

3. Rotate it 90 degrees to the left or right so that the vent blower

damper is repositioned in the direction needed. Do not twist

or bind the wires or disconnect the wiring from the blower.

4. Place the bottom tab of the blower box into the bottom

mounting channel.

A. Blower box

B. Bottom mounting channel

5. 2. Lift up the blower box from the bottom mounting channel and

set aside.

Tilt blower box top tab so it is flush with the vent box panel

and position it under the top mounting bracket. Slide bracket

into the "Z" slots and tighten the 2 hex/slotted head screws

to secure.

NOTE: Optional blower motor mounting position (opposite side).

The blower motor box assembly can also be moved to the

opposite side of the vent.

1. Remove blower motor box assembly. Follow steps 1 and 2

above.

2. Disconnect the wire connector from the blower motor (see

Step 3 of rear venting).

3. Remove panel from the opposite side by loosening the

screws in the "Z" slots and sliding the top bracket the same

as for the motor box assembly.

4. Install the blower motor box assembly to the opposite side of

vent box. Place in the position for the venting method for

interior mounted motor, as required.

5. Reconnect wire connector to the blower motor.

6. Install panel cover to the opposite side of the blower motor.

Rear Venting:

1. Remove the vent box. Loosen the 2 hex/slotted head screws

that attach the top bracket that secures the motor to the vent

box enough to slide the bracket into the "Z" slots. This will

move the bracket away from the top mounting lip of the

blower box and allow it to tilt away from the vent box panel.

A. Bracket with "Z" slots

B. Hex/slo tted head screws (2)

A.Blower box

B.Bottom mounting channel

Disconnect the wire connector from the blower motor.

A. Blower motor

B. Wire connector

Remove the 2 screws that mount the motor mounting bracket

to the vent box. Remove the blower motor and mounting

bracket assembly from the vent box.

........A

A. Blower motor mounting bracket screws (2)

Remove the 4 screws from the small cover plate on the rear

of the vent chamber and set screws and cover plate aside.

Install blower motor and mounting bracket assembly to the

bracket just below the downdraft tower motor. The blower

exhaust opening should fit through the hole in the large cover

plate on the opposite side of the vent chamber where the

small cover plate was removed. Replace the 2 blower motor

mounting bracket screws and tighten.

_ C

A. Downdraft tower motor

B. Large cover plate

C. Blower exhaust opening

7. Plug in the wire connector to the blower motor.

9. Replace the vent box over the blower motor.

i,S

A.Blower motor

B. Ventbox

10. Place the bottom tab of the blower box into the bottom

mounting channel.

A B

A. Blower motor

B. Wire connector

Place the vent extension for the 6" diameter venting over the

vent exhaust and screw into place using the 4 screws.

A. Blower box

B. Bottom mounting channel

11. Tilt blower box top tab so it is flush with the vent box panel

and position it under the top mounting bracket.

12. Slide bracket into the "Z" slots.

13. Tighten the 2 hex/slotted head screws to secure.

14. Place the small vent cover over the hole in the vent box and

secure in place with the 4 screws.

A. Ventextension screws (4)

Attach backdraft damper over 6" vent extension. Secure with

vent clamp.

B_ C

A. When attaching undercounter bracket to underside

of countertop, make sure that the screw length will

not go through countertop when tightened.

B. Backsplash

C. Countertop

A. 6" vent extension

B. Backdraft damper

2. Remove screw attaching the terminal box cover.

A. Terminal box cover

Determine which direction (rear or bottom) electrical

connection will need to run from vent system terminal box.

Remove rear or bottom knockout and install a UL listed or

CSA approved conduit connector.

Insert downdraft vent into countertop cutout. Using 2 or more

people, position downdraft vent so it is centered in cutout

and parallel to edge of cutout. Check that downdraft vent is

level vertically. Then fasten lower support legs to the cabinet

floor with screws.

Attach 1 undercounter bracket on front upper right corner of

downdraft vent with slot over vent mounting hole and flange

against countertop. Attach other bracket to left side of the

downdraft vent. Drill starter holes through undercounter

mounting brackets into the underside of the countertop.

Insert appropriate length screws into holes and tighten

brackets to countertop.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Feed the power supply cable through the conduit connector

and into the terminal box.

Fire Hazard

Electrically ground the blower.

Use copper wire.

Connect ground wire to green ground screw in

terminal box.

Failure to do so can result in death, fire, or

electrical shock.

3. Attach the green (or green and yellow) ground wire to the

green ground screw. Tighten the conduit connector clamp

screws.

Connect the 2 white wires together using UL listed wire

connectors.

Push and hold the button on the top of the downdraft vent for

a few seconds. The retractable section of the downdraft vent

will rise, and the blower will start. Position the top trim over

the retractable section and snap trim into place.

Trim kits for matching your cooktop color are available from

your dealer.

For information on ordering, see the "Assistance or Service"

section.

A. Green or green and yellow ground wire

B. Green ground screw

C. White wires

D. UL listed wire connectors

E.Black wires

F UL listed or CSA approved conduit connector

G. Downdraft vent wiring

Connect the 2 black wires together using UL listed wire

connectors.

Replace the terminal box cover and secure with screw.

Reconnect power.

A. Top trim

B. ON/OFF button

C. Blower control sfider

D. End cap

E.Filters

Slide the control slider on the side of vent to check the

operation and speed of the blower.

If the blower does not operate:

• Check that filter or filters are pressed in as far as they will

go.

• Check that the circuit breaker has not tripped or a

household fuse blown.

• Check downdraft fuse located under power board.

4. Connect vent system to blower. Vent system must end with a

wall or roof cap. Use clamps to seal all joints.

5. Install cooktop according to manufacturer's instructions.

Check that rear of cooktop overlaps edge of retractable

downdraft vent by 3/8"(9.5 mm). See "Countertop Cutout

Dimensions" in the "Location Requirements" section.

NOTE: To get the most efficient use from your new retractable

downdraft vent, read the "Vent System Use" section.

INSTALLATION INSTRUCTIONS

EXTERIOR-MOUNTED VENT MOTOR

KIRD and YKIRD Models Only

IMPORTANT: Exterior blower Model No. KPEU722M [1200 cfm

(34.0 m_/3)] cannot be used with this retractable downdraft vent

system.

NOTE: Exterior-mounted vent motor installations require exterior

blower system, Model No. KPEC992M [900 cfm (25.5 m3/m)],

available from your dealer or authorized parts supplier.

Determine which venting method is best for your application.

Vent system can terminate through either the wall or roof.

Island location

,[7 ,

Built-in cabinet locations

A B

A. Left venting

B. 10" round 90° elbow

B A

A.Right venting

g. o10" round 90 elbow

Roof Venting

A. 10" (25.4 cm) round vent

Calculating Vent System Length

It is recommended that you use round vent instead of rectangular

vent, especially if elbows are required. If rectangular vent is

required, it should be transitioned to 10" (25.4 cm) round vent as

soon as possible.

Maximum Length of Vent System

Vent Length

10" (25.4 cm) round 40 ft (12.2 m)

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent Piece 10" (25.4 cm) Round

45° elbow 2.5 ft _

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

Example Vent System

--ix

A. External blower motor

B. Straight vent

C. 90 ° elbows

The following example falls within the maximum vent length of

40 ft (12.2 m).

2 - 90° elbows

= 10.0 ft (3 m)

= 20 ft (6 m)

10 ft (3 m) straight

Length of 10" (25.4 cm)

system

NOTE: The exterior-mounted vent motor requires a separate

wiring cable that should be installed at the same time the vent

work is installed.

Excessive Weight Hazard

Use two or more people to move and install

downdraft vent.

Failure to do so can result in back or other injury.

1. Place cardboard or similar material on top of a flat surface

where you can easily assemble the downdraft vent system.

2. Remove parts packages and downdraft vent from carton.

3. Remove all shipping materials, tape and film from downdraft

vent.

4. Remove screws from each side of the vent. Attach the left

and right side overcounter support brackets to the downdraft

vent and push up to align the screw holes. Use screws to

secure the brackets.

"<_9.........................................C

A. Overcounter support bracket

B. 10" round vent mounting collar plate

C. Qvercounter support bracket screw

Attach the left and right side end caps to the downdraft vent.

Place the end cap upon the overcounter support, slide the

tab into the slot and snap into place over the the plastic tabs.

A. End cap

Attach support legs to side of downdraft vent with 2 screws

in each leg. Do not tighten screws.

A. Blower motor box

B. Support leg

7. Using 2 or more people, insert the downdraft vent into the

countertop cutout. Check that downdraft vent is parallel to

side of cutout and that mounting brackets overlap

countertop.

8. Move support legs down against cabinet floor. Place a level

against the front of the downdraft vent base and adjust until

downdraft vent is level vertically. Use a pencil to mark the top

of each leg on the downdraft vent and the location of the

support leg mounting holes on the cabinet floor.

A. Level

B. Mark locations.

Remove downdraft vent from cutout. Drill starter holes at

each mounting screw location on the cabinet floor. Align the

top of the legs with pencil marks on the face of the downdraft

vent. Tighten screws in legs.

10. Remove the Phillips-head screw attaching the terminal box

cover and remove cover.

A. Terminal box cover

Remove either the back or bottom knockout inside the

terminal box and install a UL listed or CSA approved conduit

connector.

NOTE: Power supply cable needed between exterior blower

assembly and blower box is not provided.

Flexible armored or nonmetallic cable must be used. A

1/2"(12.7 cm) UL listed or CSA approved strain relief must be

provided at each end of the power supply cable.

11. Determine the location where the exterior blower box will be

located. Cut opening in roof or wall for vent system to exterior

blower. Install exterior blower according to instructions

supplied with the blower kit.

Wall Installations:

• Use caulking compound between mounting flange and

wall.

Roof Installations:

Follow standard roofing procedures. Refer to the "Roof

Installations" section of the Exterior Blower Installation

Instructions.

The flashing sheet should be centered over the roof

opening.

Lower edge of flashing should lie on top of shingles and

upper edge underneath shingles.

Seal assembly between roof, fan and flashing with roofing

mastic to avoid leaks.

12. Using 2 or more people, insert the downdraft vent into the

countertop cutout. Position downdraft vent so it is centered

in cutout and parallel to edge of cutout. Check that downdraft

vent is level vertically. Then fasten lower support legs to the

cabinet floor with screws.

13. Attach 1 undercounter bracket on front upper right corner of

downdraft vent with slot over vent mounting hole and flange

against countertop. Attach other bracket to left side of the

downdraft vent. Drill starter holes through undercounter

mounting brackets into the underside of the countertop.

Insert appropriate length screws into holes and tighten

brackets to the countertop.

B-I_ C

A. When attaching undercounter bracket to underside

of countertop, make sure that the screw length will

not go through countertop when tightened.

B. Backsplash

C. Countertop

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Feed the home power supply cable through the conduit

connector and into the terminal box.

3. Remove vent box knockout and install a UL listed or CSA

approved conduit connector. Feed exterior-mounted vent

motor wiring through conduit connector.

J /

A.Green or green and yellow ground wires

B. Green ground screw

C. Blue wires

D. UL listed wire connector

E.Brown wires

F. Downdraft vent wiring

G. Black wires

H. White wires

I. UL listed or CSA approved conduit and connector,

(Home power supply cable).

J. UL listed or CSA approved conduit and connector,

(Exterior-mounted vent motor wiring).

Fire Hazard

Electrically ground the blower.

Use copper wire.

Connect ground wire to green ground screw in

terminal box.

Failure to do so can result in death, fire, or

electrical shock.

Attach the 2 green (or green and yellow) ground wires from

the home power supply cable and the exterior-mounted vent

motor wiring to the green ground screw.

IMPORTANT: Exterior vent motor wires must be connected in

the terminal box as shown.

5. Connect the 2 blue wires together using UL listed wire

connectors.

6. Connect the 2 brown wires together using UL listed wire

connectors.

7. Connect the 2 white wires together using UL listed wire

connectors.

8. Connect the 2 black wires together using UL listed wire

connectors.

9. Tighten conduit connector clamp screws.

10. Replace the terminal box cover and secure with screw.

11. Reconnect power.

Push and hold the button on the top of the downdraft vent for

a few seconds. The retractable section of the downdraft vent

will rise. The blower will start immediately if the blower control

knob is set to an "on" position.

Position the top trim over the retractable section and snap

trim into place.

Trim kits for matching your cooktop color are available from

your dealer.

For information on ordering, see the "Assistance or Service"

section.

A. Top trim

B. ON/OFF button

C. Blower control slider

D. End cap

E. Filters

3. Slide the control slider on the side of the vent to check the

speed of the blower.

If the blower does not operate:

• Check that filter or filters are pressed in as far as they

will go.

• Check that circuit breaker has not tripped or a household

fuse blown.

• Check downdraft fuse located under power board.

4. Connect vent system to 10" (25.4 cm) round vent collar plate.

Position vent to avoid wall studs and floor joists. Complete all

vent work. Use clamps to seal all joints.

Vertical vent for wall-mounted installations should pitch down

slightly toward the vent to allow moisture to run outside.

5. Install cooktop according to manufacturer's instructions.

Check that rear of cooktop overlaps edge of retractable

downdraft vent by 3/8"(9.5 mm). See "Countertop Cutout

Dimensions" in the "Location Requirements" section.

NOTE: To get the most efficient use from your new retractable

downdraft vent, read the "Vent System Use" section.

VENT SYSTEM USE

The retractable downdraft vent system is designed to remove

smoke, cooking vapors and odors from the cooktop area.

• For best results, the vent should be operating before cooking

is started.

• If you use large or tall utensils, place them on the large rear

element or burner surface.

• A higher heat setting than normally used may be needed

when the downdraft vent is operating.

• This fan is suitable for use with solid-state speed controls.

To Use:

1. Push and hold the button on top of downdraft vent for a few

seconds. (This slight delay helps avoid inadvertent raising of

the vent during cleaning of the cooktop area.) Retractable

section of downdraft vent will rise. Blower will begin to vent

immediately if blower control knob slider is set to an "On"

position.

2. Slide the control slider on the right-hand side of the

downdraft vent to adjust the blower motor speed.

When cooking is complete:

1. Push the button on top of the retractable downdraft vent. The

blower will turn off, and the retractable section of the vent will

return to the closed position.

If a spill occurs on the cooktop that allows liquids to seep inside

the downdraft, you must turn the downdraft off immediately. It is

possible to cause damage to the downdraft if water is allowed

inside the downdraft while it is operating.

1. Immediately turn off the downdraft at the speed control

located on the right-hand side of the downdraft.

2. Turn off the power supply to the downdraft at the circuit

breaker box or fuse box.

3. Allow plenty of time for the downdraft to dry naturally. Do not

open the downdraft to remove the water.

VENT SYSTEM CARE

I VOII:I

Toavoid damaging the finish, clean downdraft vent with soap

and water.Do not usescouring powder or abrasive solutions.

Frequently remove and clean the filter(s) inthe retractable section

of the downdraft vent. This will improve the operating efficiency

of the downdraft vent system.

To Remove Filters:

1. Place fingertips in the embossment at the top for the filters.

2. Press down on the filters far enough for the tab at the top of

the filters to clear.

3. Pull forward to release the filter from its groove.

To Replace Filters:

1. Place filters into the retractable section of the downdraft vent.

2. Place fingertips into the embossment at the top of the filters

and push down and back to allow the top tabs to snap into

place.

NOTE: Downdraft will not operate if the filters are not in their

proper position. If the filters' top tabs are not locked behind the

top flange, the vent may retract but not raise back up.

If retractable downdraft vent does not operate after clean

filters have been installed:

Push the filter in as far as it will go. When the filter is removed, the

microswitch behind the filter is inactivated. This feature will not

allow the vent system to operate until the filter is properly

installed.

To Clean:

1. Remove the filter(s) and clean them in a dishwasher or in a

hot detergent solution. The downdraft vent will not operate

when the filters are not in place.

2. Dry the clean filter(s) and reinstall, making sure that they lock

into place.

A. Filter removal embossment

B. Left metal filter

C. Right metal filter

WIRING DIAGRAM

5x20 800 mA

Time Delay

_RED _ RED

×iii___ _ "-' _}L_=BLKI)--IaxBLK

O a _ ( FILTER _ O

"L__ I [SWITCHES)

I ( GRY

GRY

I TOROIDAL 1

TRANSFORMER

BLK

CN6 CN7

TR1

C700C4

RL2

tit'

BLU

BRW

PUSH BUTTON q _ SPEED

UPIDOWN ) [REGULATION)

[_RL1

<_ SiDE INSERTCABLES

CN8

CN2

ORG

FLAT CABLE

GRY

WHT

O BLK

]_ -':"

LINE IN 120

Vac 60 Hz

=p( B,ow .

La page charge ...

KitchenAid KIRD801VSS0 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KIRD801VSS0

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KIRD801VSS0 Owner's manual

KitchenAid KIRD801VSS0 Le manuel du propriétaire

Ce manuel convient également à

KitchenAid KIRD801VSS0 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents