Black & Decker Cordless Saw FS110L Manuel utilisateur

Marque: Black & Decker

Modèle: Cordless Saw FS110L

Catégorie: Scies à onglet

Taper: Manuel utilisateur

Ce manuel convient également à

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

POUR LE FRANÇAIS, VOIR LA COUVERTURE ARRIÈRE.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y

PÓLIZA DE GARANTÍA. ADVERTENCIA: LÉASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

””

HANK

YOU

FOR

CHOOSING

IREST

ORM

WWW

IREST

ORMT

OOLS

COM

RODUCT

EGISTRA

TION

YOUR

NEW

PRODUCT

BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A

CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

For your convenience and safety, the following warning labels are on your miter saw.

ON MOTOR HOUSING:

WARNING: FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING SAW. WHEN SERVICING, USE

ONLY IDENTICAL REPLACEMENT PARTS. ALWAYS WEAR EYE PROTECTION.

ON FENCE: CLAMP SMALL PIECES BEFORE CUTTING. SEE MANUAL

ON GUARD: DANGER – KEEP AWAY FROM BLADE.

ON GUARD RETAINER PLATE: To reduce the risk of injury, read instruction manual before operating miter saw. When servicing,

use only identical replacement parts. Do not expose to rain or use in damp locations. Always use proper eye and respiratory

protection. Use only 10" (254mm) saw blades recommended for 5200RPM or higher with 5/8" arbor." Keep hands out of path of saw

blade. Do not operate saw without guards in place. Check lower guard for proper closing before each use. Always tighten adjustment

knobs before use. Do not perform any operation freehand. Never reach in back of saw blade. Never cross arms in front of blade.

Turn off tool and wait for saw blade to stop before moving workpiece, changing settings or moving hands. Disconnect power before

changing blade or servicing. To reduce the risk of injury, return carriage to the full rear position after each crosscut operation. Think!

you can prevent accidents.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may

result in property damage.

This manual contains information that is important for you to know and understand. This information relates to

protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we

use the symbols below. Please read the manual and pay attention to these sections.

SAFETY GUIDELINES - DEFINITIONS

GENERAL SAFETY RULES

READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE

USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in

electric shock, fire, and/or serious personal injury or property damage.

IMPORTANT SAFETY INSTRUCTIONS

Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there are certain

hazards involved with the operation of the product. Using the machine with respect and caution will considerably lessen the

possibility of personal injury. However, if normal safety precautions are overlooked or ignored, personal injury to the operator may

result. Safety equipment such as guards, push sticks, hold-downs, featherboards, goggles, dust masks and hearing protection

can reduce your potential for injury. But even the best guard won’t make up for poor judgment, carelessness or inattention.

Always use common sense

and exercise caution in the workshop. If a procedure feels dangerous, don’t try it. Figure out an

alternative procedure that feels safer. REMEMBER: Your personal safety is your responsibility.

CLAMP SMALL PIECES

BEFORE CUTTING. SEE MANUAL.

DANGER

KEEP AWAY

FROM BLADE

ON TABLE: (2 PLACES)

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains

chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these

chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities. Wear protective

clothing and wash exposed areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may promote

absorption of harmful chemicals.

Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or

other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct

particles away from face and body.

Wear appropriate hearing protection during use. Under some conditions and duration of use, noise from this

product may contribute to hearing loss.

DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS.

1. FOR YOUR OWN SAFETY, READ AND

UNDERSTAND THE INSTRUCTION MANUAL

BEFORE OPERATING THE MACHINE. Learning the

machine’s application, limitations, and specific

hazards will greatly minimize the possibility of

accidents and injury.

2. USE CERTIFIED SAFETY EQUIPMENT. Eye

protection equipment should comply with ANSI

Z87.1 standards, hearing equipment should

comply with ANSI S3.19 standards, and dust

mask protection should comply with

NIOSH/OSHA certified respirator standards.

Splinters, air-borne debris, and dust can cause

irritation, injury, and/or illness.

3. DRESS PROPERLY. Do not wear tie, gloves, or

loose clothing. Remove watch, rings, and other

jewelry. Roll up your sleeves. Clothing or jewelry

caught in moving parts can cause injury.

4. DO NOT USE THE MACHINE IN A

DANGEROUS ENVIRONMENT. The use of

power tools in damp or wet locations or in rain

can cause shock or electrocution. Keep your

work area well-lit to prevent tripping or placing

arms, hands, and fingers in danger.

5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK

CONDITION. Keep tools sharp and clean for best and

safest performance. Follow instructions for lubricating

and changing accessories. Poorly maintained tools and

machines can further damage the tool or machine

and/or cause injury.

6. CHECK FOR DAMAGED PARTS. Before using the

machine, check for any damaged parts. Check

for alignment of moving parts, binding of moving

parts, breakage of parts, and any other

conditions that may affect its operation. A guard

or any other part that is damaged should be

properly repaired or replaced. Damaged parts

can cause further damage to the machine and/or

injury.

7. KEEP THE WORK AREA CLEAN. Cluttered areas and

benches invite accidents.

8. KEEP CHILDREN AND VISITORS AWAY. Your shop is

a potentially dangerous environment. Children and

visitors can be injured.

9. REDUCE THE RISK OF UNINTENTIONAL

STARTING. Make sure that the switch is in the

“OFF” position before plugging in the power cord.

In the event of a power failure, move the switch

to the “OFF” position. An accidental start-up can

cause injury.

10. USE THE GUARDS. Check to see that all guards

are in place, secured, and working correctly to

prevent injury.

11. REMOVE ADJUSTING KEYS AND WRENCHES

BEFORE STARTING THE MACHINE. Tools,

scrap pieces, and other debris can be thrown at

high speed, causing injury.

12. USE THE RIGHT MACHINE. Don’t force a

machine or an attachment to do a job for which it

was not designed. Damage to the machine

and/or injury may result.

13. USE RECOMMENDED ACCESSORIES. The use

of accessories and attachments not

recommended by Black & Decker may cause

damage to the machine or injury to the user.

14. USE THE PROPER EXTENSION CORD. Make

sure your extension cord is in good condition.

When using an extension cord, be sure to use

one heavy enough to carry the current your

product will draw. An undersized cord will cause

a drop in line voltage, resulting in loss of power

and overheating. See the Extension Cord Chart

for the correct size depending on the cord length

and nameplate ampere rating. If in doubt, use the

next heavier gauge. The smaller the gauge

number, the heavier the cord.

15. SECURE THE WORKPIECE. Use clamps or a vise

to hold the workpiece when practical. Loss of

control of a workpiece can cause injury.

16. FEED THE WORKPIECE AGAINST THE DIRECTION

OF THE ROTATION OF THE BLADE, CUTTER, OR

ABRASIVE SURFACE. Feeding it from the other

direction will cause the workpiece to be thrown

out at a high speed.

17. DON’T FORCE THE WORKPIECE ON THE

MACHINE. Damage to the machine and/or injury

may result.

18. DON’T OVERREACH. Loss of balance can make

you fall into a working machine, causing injury.

19. NEVER STAND ON THE MACHINE. Injury could occur

if the tool tips, or if you accidentally contact the cutting

tool.

20. NEVER LEAVE THE MACHINE RUNNING

UNATTENDED. TURN THE POWER OFF. Don’t leave

the machine until it comes to a complete stop. A child or

visitor could be injured.

21. TURN THE MACHINE “OFF”, AND DISCONNECT

THE MACHINE FROM THE POWER SOURCE before

installing or removing accessories, before

adjusting or changing set-ups, or when making

repairs. An accidental start-up can cause injury.

22. MAKE YOUR WORKSHOP CHILDPROOF WITH

PADLOCKS, MASTER SWITCHES, OR BY

REMOVING STARTER KEYS. The accidental

start-up of a machine by a child or visitor could

cause injury.

23. STAY ALERT, WATCH WHAT YOU ARE DOING,

AND USE COMMON SENSE. DO NOT USE THE

MACHINE WHEN YOU ARE TIRED OR UNDER

THE INFLUENCE OF DRUGS, ALCOHOL, OR

MEDICATION. A moment of inattention while

operating power tools may result in injury.

24. THE DUST GENERATED by certain woods and

wood products can be injurious to your health.

Always operate machinery in well-ventilated areas,

and provide for proper dust removal. Use wood

dust collection systems whenever possible.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

ADDITIONAL SAFETY RULES FOR MITER SAWS

Refer to them often and use them to instruct others.

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS INJURY.

SAVE THESE INSTRUCTIONS.

1. DO NOT OPERATE THIS MACHINE until it is

completely assembled and installed according to the

instructions. A machine incorrectly assembled can

cause serious injury.

2. OBTAIN ADVICE from your supervisor, instructor, or

another qualified person if you are not thoroughly

familiar with the operation of this machine. Knowledge

is safety.

3. FOLLOW ALL WIRING CODES and recommended

electrical connections to prevent shock or electrocution.

4. SECURE THE MACHINE TO A SUPPORTING SURFACE.

Vibration can possibly cause the machine to slide, walk,

or tip over, causing serious injury.

5. USE ONLY CROSSCUT SAW BLADES. Use only

zero-degree or negative hook angles when using

carbide-tipped blades. Do not use blades with deep

gullets. These can deflect and contact the guard, and

can cause damage to the machine and/or serious

injury.

6. USE ONLY BLADES OF THE CORRECT SIZE AND

TYPE specified for this tool to prevent damage to the

machine and/or serious injury.

7. USE A SHARP BLADE. Check the blade to see if it

runs true and is free from vibration. A dull blade or a

vibrating blade can cause damage to the machine

and/or serious injury.

8. INSPECT BLADE FOR CRACKS or other damage prior

to operation. A cracked or damaged blade can come

apart and pieces can be thrown at high speeds,

causing serious injury. Replace cracked or damaged

blades immediately.

9. CLEAN THE BLADE AND BLADE FLANGES prior to

operation. Cleaning the blade and flanges allows you to

check for any damage to the blade or flanges. A

cracked or damaged blade or flange can come apart

and pieces can be thrown at high speeds, causing

serious injury.

10. USE ONLY BLADE FLANGES specified for this tool to

prevent damage to the machine and/or serious injury.

11. CLEAR THE AREA OF FLAMMABLE LIQUIDS and/or

gas prior to operation. Sparks can occur that would

ignite the liquids and cause a fire or an explosion.

12. CLEAN THE MOTOR AIR SLOTS of chips and

sawdust. Clogged motor air slots can cause the

machine to overheat, damaging the machine and

possibly causing a short which could cause serious

injury.

13. TIGHTEN THE TABLE CLAMP HANDLE and any other

clamps prior to operation. Loose clamps can cause

parts or the workpiece to be thrown at high speeds.

14. NEVER START THE TOOL with the blade against the

workpiece. The workpiece can be thrown, causing

serious injury.

15. KEEP ARMS, HANDS, AND FINGERS away from the

blade to prevent severe cuts. Clamp all workpieces that

would cause your hand to be in the “Table Hazard

Zone” (within the red lines).

16. ALLOW THE MOTOR TO COME TO FULL SPEED

prior to starting cut. Starting the cut too soon can

cause damage to the machine or blade and/or serious

injury.

17. NEVER REACH AROUND or behind the saw blade. A

moving blade can cause serious injury.

18. NEVER CUT FERROUS METALS or masonry. Either of

these can cause the carbide tips to fly off the blade at

high speeds causing serious injury.

19. NEVER CUT SMALL PIECES. Cutting small pieces

(where your hand would be within 6” of the saw blade)

can cause your hand to move into the blade, resulting

in serious injury.

20. NEVER LOCK THE SWITCH in the “ON” position.

Setting up the next cut could cause your hand to move

into the blade, resulting in severe injury.

21. NEVER APPLY LUBRICANT to a running blade.

Applying lubricant could cause your hand to move into

the blade, resulting in serious injury.

22. DO NOT PERFORM FREE-HAND OPERATIONS

(wood that is not held firmly against the fence and

table). Hold the work firmly against the fence and table.

Free-hand operations on a miter saw could cause the

workpiece to be thrown at high speeds, causing

serious injury. Use clamps to hold the work when

possible.

23. PROPERLY SUPPORT LONG OR WIDE WORK-

PIECES. Loss of control of the workpiece can cause

serious injury.

24. AFTER COMPLETING CUT, release power switch and

wait for coasting blade to come to a complete stop

before returning saw to raised position. A moving blade

can cause serious injury.

25. TURN OFF THE MACHINE and allow the blade to

come to a complete stop prior to cleaning the blade

area or removing debris in the path of the blade. A

moving blade can cause serious injury.

26. TURN OFF MACHINE and allow the blade to come to

a complete stop before removing or securing

workpiece, changing workpiece angle, or changing the

angle of the blade. A moving blade can cause serious

injury.

27. PROPERLY SUPPORT LONG OR WIDE WORK-

PIECES. Loss of control of the workpiece can cause injury.

28. NEVER PERFORM LAYOUT, ASSEMBLY, OR SET-UP

WORK on the table/work area when the machine is

running. A sudden slip could cause a hand to move

into the blade. Severe injury can result.

29. TURN THE MACHINE “OFF”, disconnect the machine

from the power source, and clean the table/work area

before leaving the machine. LOCK THE SWITCH IN

THE “OFF” POSITION to prevent unauthorized use.

Someone else might accidentally start the machine and

cause injury to themselves.

30. BEFORE OPERATING THE SAW, check and securely

lock the bevel, miter, and sliding fence adjustments.

31. THE CUTTING HEAD MUST RETURN QUICKLY TO

THE FULL UP POSITION. Failure to do so will not allow

the lower guard to operate properly and may result in

personal injury. See manual section on “Adjusting the

Cuttinghead Return”.

32. THE CUTTING HEAD MUST RETURN QUICKLY TO

THE FULL UP POSITION. Failure to do so will not allow

the lower guard to operate properly and may result in

personal injury. See manual section on “Adjusting the

Cuttinghead Return”.

33. ADDITIONAL INFORMATION regarding the safe and

proper operation of power tools (i.e. a safety video) is

available from the Power Tool Institute, 1300 Sumner

Avenue, Cleveland, OH 44115-2851 (www.powertool

institute.com). Information is also available from the

National Safety Council, 1121 Spring Lake Drive,

Itasca, IL 60143-3201. Please refer to the American

National Standards Institute ANSI 01.1 Safety

Requirements for Woodworking Machines and the U.S.

Department of Labor regulations.

THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM ELECTRIC

SHOCK.

A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and

should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which

have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before

connecting the machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric

current is of the same characteristics as indicated on the machine. All line connections should make good contact.

Running on low voltage will damage the machine.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

1. All grounded, cord-connected machines:

In the event of a malfunction or breakdown, grounding

provides a path of least resistance for electric current to

reduce the risk of electric shock. This machine is

equipped with an electric cord having an equipment-

grounding conductor and a grounding plug. The plug

must be plugged into a matching outlet that is properly

installed and grounded in accordance with all local

codes and ordinances.

Do not modify the plug provided - if it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

Improper connection of the equipment-grounding

conductor can result in risk of electric shock. The

conductor with insulation having an outer surface that

is green with or without yellow stripes is the

MOTOR SPECIFICATIONS

GROUNDING INSTRUCTIONS

FOR LASER SAFETY OBSERVE THE FOLLOWING:

• LASER LIGHT - DO NOT STARE INTO BEAM, APERTURE, or into a reflection

from a mirror-like surface Fig. A & B.

• AVOID EXPOSURE - LASER LIGHT IS EMITTED FROM FRONT GUARD

APERTURE. Use of controls or adjustments, or performance of procedures

other than those specified herein may result in hazardous laser light exposure.

• DO NOT DISASSEMBLE LASER MODULE. The laser is a CLASS II LASER

PRODUCT that can emit laser power up to 1 mW MAX at 650 nm, which could

result in exposure with the module disassembled. The laser unit complies with

21 CFR 1040.10 and 1040.11.

• USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

• THE USE OF OPTICAL INSTRUMENTS with this product will increase eye

hazard.

• LASER RADIATION, avoid direct eye exposure, serious eye injury can result.

• DO NOT OPERATE IN EXPLOSIVE ATMOSPHERES, such as in the presence of

flammable liquids, gases, or dust.

• USE ONLY WITH THE SPECIFICALLY DESIGNATED BATTERIES. Use of any

other batteries may create a risk of fire.

• USE ONLY ACCESSORIES that are recommended by the manufacturer for your

model.

• ACCESSORIES THAT MAY BE SUITABLE FOR ONE LASER, may create a risk of

injury when used on another laser.

• REPAIRS AND SERVICING MUST be performed by a qualified repair facility.

Repairs performed by unqualified personnel could result in serious injury.

• DO NOT REMOVE OR DEFACE WARNING LABELS. Removing labels increases

the risk of exposure to radiation.

• THIS PRODUCT IS INTENDED for use in a temperature range of 41°F(5°C) -

104°F(40°C).

ADDITIONAL SAFETY RULES FOR THE LASER

Fig. B

Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source,

make sure the switch is in the “OFF” position.

Fig. A

equipment-grounding conductor. If repair or

replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to

a live terminal.

Check with a qualified electrician or service personnel if

the grounding instructions are not completely

understood, or if in doubt as to whether the machine is

properly grounded.

Use only 3-wire extension cords that have 3-prong

grounding type plugs and matching 3-conductor

receptacles that accept the machine’s plug, as shown in

Fig. C. Repair or replace damaged or worn cord

immediately.

2. Grounded, cord-connected machines intended

for use on a supply circuit having a nominal rating

less than 150 volts:

POWER CONNECTIONS

For your convenience and safety the

following labels are on your tool.

available. The temporary adapter should be used only

until a properly grounded outlet can be installed by a

qualified electrician. The green-colored rigid ear, lug, and

the like, extending from the adapter must be connected

to a permanent ground such as a properly grounded

outlet box. Whenever the adapter is used, it must be

held in place with a metal screw.

EXTENSION CORDS

FOREWORD

Model FS110L is a 10" Compound Power Laser Miter Saw designed to cut wood, plastic, and aluminum. Compound

angle and bevel cutting are easy and accurate. It can crosscut up to 5-5/8" x 2-3/4", miter at 45° both left and right 4"

x 2-3/4", bevel at 45° left 5-5/8" x 1-5/8", and compound 45° x 45°, 4" x 1-5/8". It has positive miter at 0°, 15.5°,

22.5°,30° and 45° both left and right, and bevel stops at 0° and 45° degrees adjustable.

FUNCTIONAL DESCRIPTION

UNPACKING AND CLEANING

Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from

all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,

gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household

floor paste wax.

NOTICE: The manual cover photo illustrates the current production model. All other illustrations are

representative only and may not depict the actual color, labeling, or accessories, and are intended to

illustrated technique only.

Use proper extension cords. Make sure

your extension cord is in good

condition and is a 3-wire extension cord which has a

3-prong grounding type plug and matching receptacle

which will accept the machine’s plug. When using an

extension cord, be sure to use one heavy enough to

carry the current of the machine. An undersized cord

will cause a drop in line voltage, resulting in loss of

power and overheating. Fig. E shows the correct gauge

to use depending on the cord length. If in doubt, use

the next heavier gauge. The smaller the gauge number,

the heavier the cord.

Fig. E

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES

Ampere Total Length Gauge of

Rating Volts of Cord in Feet Extension Cord

0-6 120

up to

25 18 AWG

0-6 120 25-50 16 AWG

0-6 120 50-100 16 AWG

0-6 120 100-150 14 AWG

6-10 120

up to

25 18 AWG

6-10 120 25-50 16 AWG

6-10 120 50-100 14 AWG

6-10 120 100-150 12 AWG

10-12 120

up to

25 16 AWG

10-12 120 25-50 16 AWG

10-12 120 50-100 14 AWG

10-12 120 100-150 12 AWG

12-16 120

up to

25 14 AWG

12-16 120 25-50 12 AWG

12-16 120

GREATER THAN 50 FEET NOT RECOMMENDED

GROUNDED OUTLET BOX

CURRENT

CARRYING

PRONGS

GROUNDING BLADE

IS LONGEST OF THE 3 BLADES

GROUNDED OUTLET BOX

GROUNDING

MEANS

ADAPTER

IN ALL CASES, MAKE CERTAIN THAT THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED.

IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.

NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.

If the machine is intended for use on a circuit that has an

outlet that looks like the one illustrated in Fig. C, the

machine will have a grounding plug that looks like the

plug illustrated in Fig. C. A temporary adapter, which

looks like the adapter illustrated in Fig. D, may be used to

connect this plug to a matching 2-conductor receptacle

as shown in Fig. D if a properly grounded outlet is not

EXTENSION CORDS

Fig. C

Fig. D

CARTON CONTENTS

1. Miter Saw

2. Dust Bag

3. Clamp

4. 5mm Hex Wrench

5. 1/8” Hex Wrench

6. 1/2” Blade Wrench

Lifting the miter saw by the switch handle can cause misalignment. Always lift the machine by

the base or the carrying handle.

ASSEMBLY

For your own safety, do not connect the

machine to the power source until the machine is

completely assembled, and you read and understand

the entire instruction manual.

Fig. 1 Fig. 2

Remove the miter saw and all loose items from the carton.

ROTATING TABLE

Loosen the table-lock handle one or two turns. Raise the index

lever (B) Fig. 3 and rotate the table to the desired position.

Tighten the table-lock handle (A) Fig. 3.

Fig. 3

MOVING CUTTINGHEAD TO THE UP POSITION

1. Push down on the cuttinghead and pull out the

cuttinghead lock knob (A) Fig. 4.

2. Move the cuttinghead to the up position.

Fig. 4

ASSEMBLY TOOLS REQUIRED

(Supplied)

* 5mm hex wrench

* 1/8” hex wrench

* 1/2” blade wrench

(Not supplied)

* Phillips head screwdriver

* A square to make adjustments

ATTACHING DUST BAG

Attach the dust bag (A) Fig. 5 to the dust spout (B)

making sure the wire ring (C) is engaged with the ridge

in the spout (see inset).

Fig. 5

FASTENING MACHINE TO SUPPORTING SURFACE

Before operating your compound miter saw, mount it to

a sturdy workbench or other supporting surface. Four

holes are provided, two of which are shown at (A) Fig. 6.

When frequently moving the saw from place to place,

mount the saw to a 3/4”piece of plywood. The tool

can then be easily moved from place to place and the

plywood can be clamped to a supporting surface using

“C” clamps.

Fig. 6

OPERATING CONTROLS AND ADJUSTMENTS

TABLE HAZARD AREA

The area inside the two red lines on

the table (A) Fig. 7 is designated as a

"HAZARD ZONE". Never place your

hands inside this area while the

machine is running. Maintain hands

6” from blade.

Keep your hands out of the path of

the saw blade. If necessary, clamp

the workpiece in place before making

the cut if hands would be within 6” of

blade.

Fig. 7

WORK CLAMP

Fig. 8

Position the work clamp in one of the two holes (B)

Fig 8 in the left or right side of the base. Use this

clamp, especially with short workpieces.

STARTING AND STOPPING THE MITER SAW

The torque developed during braking may loosen the arbor screw. Check the arbor screw

periodically and tighten, if necessary.

LOCKING THE SWITCH IN THE “OFF” POSITION

When the machine is not in use, the

switch should be locked in the “OFF”

position, using a padlock (B) Fig. 10

with a 3/16" diameter shackle to

prevent unauthorized use.

To start the miter saw, depress the switch trigger (A)

Fig. 9. To stop the miter saw, release the switch trigger.

This saw is equipped with an automatic electric blade

brake. As soon as the switch trigger (A) Fig. 9 is

released, the electric brake is activated and stops the

blade in seconds.

Fig. 9

Fig. 10

A turning saw blade can be

dangerous. After completing the cut,

release the switch trigger (A) Fig. 9 to

activate the blade brake. Keep the

cuttinghead down until the blade has

come to a complete stop.

ROTATING THE TABLE FOR MITER CUTTING

Your miter saw will cut any angle from a straight 90° cut to 47° right and left. Loosen the lock handle (A) Fig. 11 one

or two turns, depress the index lever (B), and move the control arm to the desired angle. TIGHTEN THE LOCK

HANDLE (A).

The miter saw is equipped with positive stops at the 0°, 15.0°, 22.5°,31.62° and 45° right and left positions. Loosen

the lock handle (A) Fig. 11, and move the control arm until the bottom of the index lever (B) engages into one of the

positive stops (C) Fig. 12. TIGHTEN THE LOCK HANDLE (A) Fig. 11. To disengage the positive stop, depress the

index lever (B).

In addition, an indicator (D) Fig. 11 is provided on the miter scale at the 33.9° right and left miter positions for cutting

crown molding. (Refer to the “CUTTING CROWN MOLDING” section of this manual).

IMPORTANT: Always tighten the lock handle (A) Fig. 11 before cutting.

Fig. 11

Fig. 12

POINTER AND SCALE

A pointer (A) Fig. 13 is supplied to indicate the actual angle of cut. Each line on the scale (B) represents 1 degree.

When the pointer is moved from one line to the next on the scale, the angle of cut is changed by 1 degree.

Fig. 13

When transporting the saw, lock the cuttinghead in the down position. Lower the cutting arm and push in the plunger (A)

Fig. 14 until the other end of the plunger (A) engages with the hole in the cutting arm (B).

IMPORTANT: Lifting the machine by the switch handle will cause misalignment. Always lift the machine by the

base or by the carrying handle (See Fig. 18).

LOCKING CUTTINGHEAD IN THE DOWN POSITION

Fig. 14

The cuttinghead of your compound miter saw can be

tilted to cut any bevel angle from a 90° straight cut off

to a 45° left bevel angle. Loosen bevel lock handle (A)

Fig. 15, tilt the cutting arm to the desired angle, and

tighten the lock handle (A).

Positive stops are provided to rapidly position the saw

blade at 90° and 45° to the table. Refer to the section

of this manual titled “ADJUSTING 90° AND 45°

DEGREE BEVEL STOPS.” The bevel angle of the

cutting arm is determined by the position of the pointer

(B) Fig. 15 on the scale (C).

In addition, a triangle indicator is provided on the bevel

scale at 33.9° for cutting crown molding. Refer to the

“CUTTING CROWN MOLDING” section of this

manual.

TILTING CUTTINGHEAD FOR BEVEL CUTTING

Fig. 15

ADJUSTING THE SLIDING FIT BETWEEN THE MOVABLE TABLE AND THE BASE

DISCONNECT THE MACHINE FROM THE

POWER SOURCE .

To adjust the sliding fit between the movable table and the base,

turn the nut (A) Fig. 12A clockwise to increase the

sliding fit (opposite to decrease the fit). This adjustment should not

be so tight that it restricts the rotating movement of the table, or

so loose that it affects the accuracy of the saw.

Fig. 12A

IMPORTANT: Move the sliding fence to provide clearance for the blade and guard. The degree of tilt determines how

far to move the sliding fence. Refer to the section “Adjusting Sliding Fence”.

A rear support bar (A) Fig. 16 is provided to prevent the machine from tipping to the rear when the cuttinghead is

returned to the “up” position. For maximum support, the bar (A) Fig. 17 should be pulled out as far as possible. The

stabilizer bar (A) Fig. 18 can also be used to carry the machine.

REAR STABILIZER/CARRYING HANDLE

Fig. 16

Fig. 17

Fig. 18

SIDE SUPPORTS

This machine has two side supports to help stabilize the machine, and to help support long or wide workpieces.

The supports are located on either side of the table. The machine comes with the supports in the saw (Fig. 19A). To

utilize the supports, pull them out to their full length (Fig. 19B).

Fig. 19A

Fig. 19B

Fully extend the stabilizer bar before operating the saw.

The sliding fence (A) Fig. 15A provides support for extra large workpieces used with your saw. Set it as close as

possible to the saw blade. When miter cutting (blade 90° to the table and at an angle to the right or left), set the

fence all the way toward the blade (Fig. 15B). When bevel cutting, however (blade tilted at an angle to the table),

move the fence (A) far enough away from the blade to allow for proper clearance. To reposition the fence, loosen the

lock handle (B), and slide the fence (A) to the desired location. Tighten the lock handle (B).

ADJUSTING SLIDING FENCE

Fig. 15A

Fig. 15B

DISCONNECT MACHINE FROM POWER SOURCE.

1. Loosen the bevel lock handle and move the cutting arm all the way to the right. Tighten the bevel lock handle.

2. Place one end of a square (A) Fig. 22 on the table and the other end against the blade. Check to see if the blade

is 90° to the table (Fig. 22).

3. If an adjustment is necessary, loosen the locknut (A) Fig. 23. Turn the screw (B) until the head of the screw

contacts the casting (C) when the blade is 90° to the table. Tighten the locknut (B).

4. Loosen the bevel lock handle and move the cutting arm all the way to the left bevel position. Tighten the bevel

lock handle.

5. Use a combination square (A) Fig. 24 to see if the blade is at 45° to the table.

6. If an adjustment is necessary, loosen the locknut (A) Fig. 25. Turn the screw (B) until the screw (B) contacts the

casting (C) when the blade is 45 degrees to the table. Tighten the locknut.

7. Check to see that the bevel pointer (A) Fig. 26 is pointing to the 45° mark on the bevel scale. To adjust the bevel

pointer (A), loosen the screw (B) and adjust the pointer (A). Tighten the screw (B) securely.

DISCONNECT MACHINE FROM POWER

SOURCE.

1. The downward travel of the saw blade should be

limited to prevent the saw blade from contacting

any metal surfaces of the machine. This adjustment

is made by loosening the locknut (A) Fig. 21, and

turning the adjusting screw (B) in or out.

2. Lower the blade as far as possible. Rotate the

blade by hand to ensure that the teeth do not

contact any metal surfaces. Adjust if necessary.

3. After the downward travel of the saw blade has

been adjusted, tighten the locknut (A).

ADJUSTING DOWNWARD TRAVEL OF SAW BLADE

Fig. 21

ADJUSTING 90° AND 45° BEVEL STOPS

Fig. 22

Fig. 23

DISCONNECT MACHINE FROM POWER

SOURCE.

1. Lower the cutting arm. The saw blade (A) Fig. 20

should be parallel to the left edge (B) of the table

opening.

2. If an adjustment is necessary, loosen two screws

is parallel with the left edge (B) of the table

opening and centered in the slot. Then tighten the

two screws (C).

Fig. 20

ADJUSTING BLADE PARALLEL TO TABLE SLOT

Fig. 24

Fig. 26

Fig. 25

CUTTING HEAD MUST RETURN QUICKLY TO THE UP POSITION. DISCONNECT MACHINE

FROM POWER SOURCE.

The tension of the cuttinghead return spring was adjusted at the factory so that the cuttinghead returns to the “up”

position after a cut has been made. If it becomes necessary to adjust the spring tension:

Loosen the locknut (A) Fig. 27 and turn the screw (B) clockwise to increase, or counterclockwise to decrease the

spring tension. After adjustment, tighten the locknut (A).

ADJUSTING TENSION OF CUTTINGHEAD RETURN SPRING

Fig. 27

After a long period of time, an adjustment of the sliding fit

between the cuttinghead arm (B) Fig. 27A, and the

trunnion (C) may be necessary. To adjust, turn the nut (D).

This adjustment should not be so tight that it restricts the

sliding movement of the cuttinghead arm (B) or so loose

that it affects the accuracy of the saw cut.

ADJUSTING SLIDING FIT BETWEEN

CUTTINGHEAD ARM AND TRUNNION

Fig. 27A

Fig. 27B

ADJUSTING THE LOWER BLADE

GUARD

DISCONNECT THE MACHINE FROM

POWER SOURCE.

This machine incorporates a blade guard (A) Fig. 27B to

cover the rear section of the blade. After an extended

period of use, the movable lower blade guard may not

operate smoothly when the cuttinghead is lowered. This

can be corrected by adjusting nut (B) until the lower blade

guard moves freely.

Overtightening the nut could impair

guard movement.

NOTE: This unit has been designed with an articulating

rear guard. Before contacting the workpiece, the rear

guard will rotate upward to expose more of the blade as

the cuttinghead is lowered.

DO NOT REMOVE ANY OF THE BLADE

GUARDS.

Make sure that all guards are in place

and functioning properly before operating the saw.

Make sure that the fences are clear of

the guard and blade before operating the saw.

LASER USE AND ADJUSTMENT

The battery-operated laser unit (AA batteries not included) is mounted in a housing that is fitted into the upper blade

guard of the miter saw (Fig. A). (To insert the batteries, remove the screw (C) Fig. B, and slide the battery cover (D)

from the handle.) The laser projects a beam of light downward. This beam of light produces a red line-of-cut indicator,

where the saw blade will cut the workpiece. The laser unit is aligned at the factory and secured in place. A test cut

has been made with each saw to verify the laser setup. If your saw becomes misaligned or you desire additional

precision, use the following guidelines to fine tune your laser miter saw.

HOW THE LASER WORKS

HOW TO CHECK LASER ALIGNMENT

Make sure the saw is set to 0 degrees miter and bevel and clamp a 2"x 4" board on the saw. Create a partial/test cut

in the workpiece (Fig. C). Turn the laser “ON/OFF” switch (A) Fig. B) to the “ON” position. Leave the workpiece

clamped in place for the remainder of the adjustment.

Place and lock a padlock with a 3/16" shackle (B) Fig. B through the hole in the trigger switch to

prevent accidental motor startup.The padlock MUST remain in place during the adjustment procedure.

The laser line is properly positioned when the beam of light falls on the cut created by the blade (Fig. D).

3. Use the 1/8" hex wrench to turn the vertical alignment set screw (Fig. E).

If you move the cutterhead from the raised to the lowered position and

the laser line moves horizontally away from the blade, turn the vertical

alignment set screw clockwise to correct. If the laser line moves

horizontally toward the blade, turn the vertical alignment set screw

counter-clockwise to correct. (Fig. F)

4. Reinstall the cover removed in STEP 2.

Fig. F

Fig. G

TO SET KERF ADJUSTMENT

1. Use the 1/8" hex wrench (A) Fig. H to turn the kerf adjustment screw that sets the laser line to either side of the

test cut (Fig. G). To adjust the line, turn the kerf adjustment screw counter-clockwise to move the line toward the

blade and clockwise to move the line away from the blade.

2. Remove the padlock. The laser miter saw is ready for normal use.

Fig. H

BRASS

HEX

NUT

VERTICAL

ALIGNMENT

SET SCREW

Fig. E

Never turn the brass hex nut in Fig. E.

TO CHECK FOR VERTICAL ALIGNMENT

1. The vertical alignment is set correctly when the line does not move horizontally (sideways) as the cutting head is

raised and lowered. If the vertical alignment is correct, disregard this section and move to “TO SET KERF

ADJUSTMENT”.

2. If the vertical alignment is not correct, turn the kerf adjustment screw one half turn, clockwise. Remove the screws

on both sides of the laser unit cover (Fig. A). Remove the cover.

SCREW

Fig. A

Fig. C

Fig. D

Fig. B

LASER MAINTENANCE

For best laser performance, perform the following

maintenance regularly:

1. Carefully clean sawdust from each laser lens (A)

Fig. I with a cotton swab (B). Do not use solvents of

any kind since they may damage the lens. Avoid

touching sharp points of the saw blade with your

hands or fingers. Dust build-up can block the laser

and prevent it from accurately indicating the

line-of-cut.

2. Remove the blade from the saw and clean pitch

build-up from the blade (Fig. J) Pitch build-up can

block the laser and prevent it from accurately

indicating the line-of-cut.

Fig. I Fig. J

TYPICAL OPERATIONS AND HELPFUL HINTS

If the workpiece causes your hand to be in the hazard zone within 6” of the saw blade, clamp

the workpiece in place before making the cut.

Cuttinghead must return quickly to the full up position. Sluggish or incomplete return of the

cuttinghead will effect lower guard operation possibly resulting in personal injury.

1. Before cutting, make certain that the cutting arm and table are at the correct settings and firmly locked in place.

2. Place the workpiece on the table and hold or clamp it firmly against the fence (Fig. 28).

3. For best results, cut at a slow, even cutting rate.

4. Never attempt freehand cutting (wood that is not held firmly against the fence and table).

Fig. 28

AUXILIARY WOOD FENCE

Multiple or repetitive cut-off operations that result in small cut-off pieces (one inch or less) can cause the saw blade

to catch the cut-off pieces and project them out of the machine or into the blade guard and housing, possibly

causing damage or injury.

To limit the possibility of personal injury or blade guard damage, mount an auxiliary wood fence

on your saw. Keep the cutting head down until the blade stops whether or not you use an

auxiliary wood fence.

Holes are provided in the fence to attach an auxiliary fence (A) Fig. 29. This auxiliary fence is constructed of straight

wood approximately 1/2" thick by 3" high by 20" long.

NOTE: The auxiliary fence (A) is used ONLY with the saw blade in the 0° bevel position (90° to the table). When

bevel cutting (blade tilted), remove the auxiliary fence.

Fig. 29

GENERAL CUTTING OPERATIONS

Fig. 30A Fig. 30B

1. Your machine has the capacity to cut standard 2 x 4’s lying flat or on edge, at the 45° right and left miter angles

(Fig. 30A).

2. A standard 2 x 6 can be cut in the 90° straight cut-off position in one pass (Fig. 30B) or at 45° right or left miter

angles (Fig. 30C).

3. Cutting a standard 4 x 4 can be accomplished with one pass (Fig. 30D).

4. This machine has the capacity to accurately cut crown moldings and other bevel-type cuts (Fig. 30E).

5. Cutting various sizes of plastic pipe is an easy job with this machine (Fig. 30F). Material must be CLAMPED OR

HELD FIRMLY TO THE FENCE TO KEEP IT FROM ROLLING.

This is extremely important when making angle cuts.

CUTTING ALUMINUM

Aluminum extrusions used for making aluminum screens and storm windows can easily be cut with your compound

miter saw when fitted with a blade recommended for this material. The blade supplied with this saw is not

recommended for cutting aluminum. When cutting aluminum extrusions, or other sections that can be cut with a saw

blade and are within the capacity of the machine, position the material so the blade is cutting through the smallest

cross-section (Fig. 31). The wrong way to cut aluminum angles is illustrated in Fig. 32. Be sure to apply a stick wax

to the blade before cutting aluminum stock. This stick wax is available at most industrial mill supply houses. The

wax provides proper lubrication and keeps chips from adhering to the blade.

Never apply lubricant to the blade while the machine is running.

FENCE

BLADE

RIGHT

FENCE

BLADE

WRONG

Fig. 32

Fig. 31

CUTTING BOWED MATERIAL

When cutting flat pieces, first check to see if the material is bowed. If it is, make sure the material is positioned on the

table as shown in Fig. 33.

If the material is positioned the wrong way (Fig. 34), the workpiece will pinch the blade near the completion of the

cut and may cause the saw to jump or move.

RIGHT

WRONG

Fig. 33

Fig. 34

Fig. 30E

Fig. 30F

Fig. 30C

Fig. 30D

Fig. 35

Fig. 36

CUTTING CROWN MOLDING

One of the many features of the saw is the ease of

cutting crown molding. The following is an example of

cutting both inside and outside corners on 52°/38° wall

angle crown molding.

1. Move the table to the 31.62° right miter position and

lock the table in position. NOTE: A positive stop is

provided to find this angle quickly.

2. Tilt the saw blade to the 33.86° left bevel position

and tighten bevel lock handle. NOTE: A triangle

indicator is provided on the bevel scale to find this

angle quickly.

3. Place the crown molding on the table with the

CEILING EDGE of the molding against the fence,

and make the cut, as shown in Fig. 35.

NOTE: The piece of crown molding used for the

outside corner will always be on the right hand side

of the blade, as shown at (A) Fig. 35. The piece of

crown molding used for the inside corner will always

be on the left hand side of the blade, as shown at

(B) Fig. 35.

4. To make the matching halves of the inside and

outside corners, rotate the table to the 31.62° left

miter position.

NOTE: A positive stop is provided to find this angle

quickly. The saw blade is already tilted to the 33.86°

bevel position from the previous cut.

5. Place the crown molding on the table with the

WALL EDGE of the crown molding against the

fence and make the cut. Again, the piece of crown

molding used for the outside corner will always be

on the right side of the blade, as shown at (C) Fig.

36. The piece of crown molding used for the inside

corner will always be on the left side of the blade, as

shown at (D) Fig. 36.

6. Fig. 36A illustrates the two outside corner pieces; (1)

being the piece cut at (A) Fig. 35 and (2) being the

piece cut at (C) Fig. 36.

7. Fig. 36B illustrates the two inside corner pieces; (1)

being the piece cut at (B) Fig. 35, and (2) being the

piece cut at (D) Fig. 36.

45-45 CROWN MOLDING

NOTE: If you are cutting crown molding that is

45°-45°, follow the same procedure above, with the

exception that the bevel position will always be at 30°

and the miter position will be 35-1/4° to the right or left.

Fig. 36A

Fig. 36B

MAINTENANCE

CHANGING THE BLADE

Use only cross-cutting saw blades.

When using carbide-tipped blades, do not use blades with deep gullets as they can deflect and

contact the guard.

Use only 10" diameter saw blades rated for 5200 rpm or higher, and have 5/8" diameter arbor holes.

Disconnect machine from power source.

REMOVE WRENCHES (A) FIG. 39 AND (A) FIG. 40 BEFORE STARTING THE MACHINE.

The cover must be returned to its original position and the screw tightened before activating the saw. •

Failure to do so may allow the cover to contact the spinning saw blade resulting in damage to the saw and

severe personal injury.

1. Remove the screw (A) Fig. 37 and rotate the cover (B) Fig. 38 to the rear.

2. To remove the saw blade, insert the 5mm hex wrench (A) Fig. 39 into the hex hole located on the rear end of the

motor shaft to keep the shaft from turning.

3. Use a wrench (A) Fig. 40 to loosen the arbor screw (C) by turning it clockwise.

4. Remove the arbor screw (C) Fig. 40, outside blade flange (B), and saw blade from the saw arbor.

5. Attach the new saw blade making certain that the teeth of the saw blade are pointing down at the front. Attach

the outside blade flange (B) Fig. 40, then the arbor screw (C), and turn it counterclockwise, using the wrench (A)

Fig. 40. At the same time, use the hex wrench (A) Fig. 39 to keep the arbor from turning.

6. Rotate the cover back to its original position and secure it in place with the screw removed in STEP 1.

Fig. 37

Fig. 38

Fig. 39

Fig. 40

NOTE: The no-load speed of this machine is 5200 rpm.

BRUSH INSPECTION AND

REPLACEMENT

Brush life varies. It depends on the load on the motor.

Check the brushes after the first 50 hours of use for a

new machine or after a new set of brushes has been

installed. After the first check, examine them after

about 10 hours of use until such time that replacement

is necessary. To inspect the brushes, proceed as

follows:

DISCONNECT MACHINE FROM POWER

SOURCE.

1. Remove three screws (A) Fig. 41 and remove motor

cover (B).

3. Fig. 43 illustrates one of the brushes (E) removed

from the holder (C). When the carbon on either brush

(E) is worn to 3/16”in length or if either spring (F) or

shunt wire is burned or damaged in any way, replace

both brushes. If the brushes are found to be

serviceable after removing, reinstall them in the same

position.

2. The brushes are located in the two holders (C)

Fig. 42. Remove spade type terminal connector (D) and

pull out brush holders (C).

Fig. 41

Fig. 42

Fig. 43

IMPORTANT

To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and

replacement) should be performed by authorized service centers or other qualified service organizations, always using

identical replacement parts.

La page charge ...

Black & Decker Cordless Saw FS110L Manuel utilisateur

Marque: Black & Decker

Modèle: Cordless Saw FS110L

Catégorie: Scies à onglet

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Black & Decker Cordless Saw FS110L User manual
español: Black & Decker Cordless Saw FS110L Manual de usuario

Black & Decker Cordless Saw FS110L Manuel utilisateur

Ce manuel convient également à

Black & Decker Cordless Saw FS110L Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents