Mitsubishi Electric MSZ-GS18NA-U1 GS-Series 18k BTU Wall Mounted Unit Manuel utilisateur

Marque: Mitsubishi Electric

Modèle: MSZ-GS18NA-U1 GS-Series 18k BTU Wall Mounted Unit

Catégorie: Climatiseurs split-system

Taper: Manuel utilisateur

1. BEFORE INSTALLATION

1-1. THE FOLLOWING SHOULD ALWAYS BE OBSERVED FOR SAFETY

• Be sure to read these safety precautions and instructions.

 %HVXUHWRREVHUYHWKHZDUQLQJVDQGFDXWLRQVVSHFL¿HGKHUH

• After reading this manual, be sure to store it with the OPERATING INSTRUCTIONS for future reference.

• Please report to your supply authority or obtain their consent before connecting this equipment to the power supply system.

JG79N458H01 Required Tools for Installation

Phillips screwdriver

Level

Scale

Utility knife or scissors

3 in. (75 mm) hole saw

Torque wrench

Wrench (or spanner)

5/32 in. (4 mm) hexagonal wrench

Flare tool for R410A

Gauge manifold for R410A

Vacuum pump for R410A

Charge hose for R410A

Pipe cutter with reamer

MSZ-GS18NA

MSY-GS18NA

When installing multi units, refer to the

installation manual of the multi unit for out-

door unit installation.

■ Do not install the unit by yourself (user).

 ,PSURSHURULQFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHHOHFWULFVKRFNLQMXU\GXHWR

WKHXQLWIDOOLQJRUZDWHUOHDNDJH&RQVXOWDTXDOL¿HGLQVWDOOHURUWKHGHDOHUIURP

whom you purchased the unit.

■ Follow the instructions detailed in the installation manual.

 ,QFRPSOHWHLQVWDOODWLRQFRXOGFDXVH¿UHRUHOHFWULFVKRFNLQMXU\GXHWRWKHXQLWIDOO-

ing, or leakage of water.

■ When installing the unit, use appropriate protective equipment and tools for

safety.

Failure to do so could cause injury.

■ Install the unit securely in a place that can bear the weight of the unit.

If the installation location cannot bear the weight of the unit, the unit could fall

causing injury.

■ Do not alter the unit.

 ,WPD\FDXVH¿UHHOHFWULFVKRFNLQMXU\RUZDWHUOHDNDJH

■ Perform electrical work according to the installation manual and be sure to use

an exclusive circuit. Do not connect other electrical appliances to the circuit.

 ,IWKHFDSDFLW\RIWKHSRZHUFLUFXLWLVLQVXI¿FLHQWRUWKHUHLVLQFRPSOHWHHOHFWULFDO

ZRUNLWFRXOGUHVXOWLQD¿UHRUDQHOHFWULFVKRFN

■ Ground the unit correctly.

Do not connect the ground wire to a gas pipe, water pipe, lightning rod or tel-

ephone ground. Defective grounding could cause electric shock.

■ Do not damage the wires.

 'DPDJHGZLUHVFRXOGFDXVH¿UH

■ Be sure to shut off the main power when setting up the indoor P.C. board or

wiring.

Failure to do so could cause electric shock.

■ 8VHWKHVSHFL¿HGZLUHVWRVHFXUHO\FRQQHFWWKHLQGRRUDQGRXWGRRUXQLWV$W-

WDFKWKHZLUHV¿UPO\WRDYRLGDSSO\LQJVWUHVVWRWKHWHUPLQDOEORFN

 ,PSURSHUFRQQHFWLRQFRXOGFDXVH¿UH

■ 'RQRWLQVWDOOWKHXQLWLQDSODFHZKHUHÀDPPDEOHJDVPD\OHDN

If gas leaks and accumulates around the unit, it could cause an explosion.

■ Do not use intermediate connection of the power cord or the extension cord.

Do not connect many devices to one AC outlet.

 ,WFRXOGFDXVHD¿UHRUDQHOHFWULFVKRFN

■ 8VHWKHSDUWVSURYLGHGRUVSHFL¿HGSDUWVIRUWKHLQVWDOODWLRQZRUN

 7KHXVHRIGHIHFWLYHSDUWVFRXOGFDXVHDQLQMXU\RUOHDNDJHRIZDWHUGXHWRD¿UH

an electric shock, the unit falling, etc.

■ When plugging the power supply plug into the outlet, make sure that there is

no dust, blockage, or loose parts both in the outlet and on the plug. Verify that

the power supply plug is completely in the outlet.

If there is dust, blockage, or loose parts on the power supply plug or the outlet, it could

FDXVHHOHFWULFVKRFNRU¿UH,IORRVHSDUWVDUHIRXQGRQWKHSRZHUVXSSO\SOXJUHSODFHLW

■ Securely attach the electrical cover to the indoor unit and the service panel to

the outdoor unit.

If the electrical cover of the indoor unit and/or the service panel of the outdoor unit are

QRWDWWDFKHGVHFXUHO\GXVWZDWHUHWFFRXOGFROOHFWLQWKHXQLWDQGFRXOGFDXVHD¿UHRU

an electric shock.

■ When installing, relocating, or servicing the unit, make sure that no substance

RWKHUWKDQWKHVSHFL¿HGUHIULJHUDQW5$HQWHUVWKHUHIULJHUDQWFLUFXLW

Any presence of foreign substance such as air can cause abnormal pressure rise

and may result in explosion or injury. The use of any refrigerant other than that

VSHFL¿HGIRUWKHV\VWHPZLOOFDXVHPHFKDQLFDOIDLOXUHV\VWHPPDOIXQFWLRQRUXQLW

breakdown. In the worst case, this could lead to a serious impediment to securing

product safety.

■ Do not discharge the refrigerant into the atmosphere. Check that the refriger-

ant gas does not leak after installation has been completed. If refrigerant leaks

during installation, ventilate the room.

 ,IUHIULJHUDQWFRPHVLQFRQWDFWZLWKD¿UHKDUPIXOJDVFRXOGEHJHQHUDWHG

 ,IUHIULJHUDQWJDVOHDNVLQGRRUVDQGFRPHVLQWRFRQWDFWZLWKWKHÀDPHRIDIDQ

heater, space heater, stove, etc., harmful gases will be generated.

■ Use appropriate tools and piping materials for installation.

The pressure of R410A is 1.6 times higher than R22. Not using the appropriate

tools and materials, or improper installation could cause the pipes to burst causing

an injury.

■ When pumping down the refrigerant, stop the compressor before disconnecting

the refrigerant pipes.

If the refrigerant pipes are disconnected while the compressor is running and the

stop valve is open, air could be drawn in and the pressure in the refrigeration cycle

could become abnormally high, causing the pipes to burst.

■ When installing the unit, securely connect the refrigerant pipes before starting

the compressor.

If the compressor is started before the refrigerant pipes are connected and the

stop valve is open, air could be drawn in and the pressure in the refrigeration cycle

could become abnormally high, causing the pipes to burst.

■ )DVWHQDÀDUHQXWZLWKDWRUTXHZUHQFKDVVSHFL¿HGLQWKLVPDQXDO

 ,IIDVWHQHGWRRWLJKWDÀDUHQXWFRXOGEUHDNDQGFDXVHUHIULJHUDQWOHDNDJH

■ Install the unit according to national wiring regulations.

■ When opening or closing the valve below freezing temperatures, refrigerant may

spurt out from the gap between the valve stem and the valve body, resulting in

injuries.

■ Depending on the installation area, install a Ground Fault Interrupt (GFI) circuit

breaker.

If the Ground Fault Interrupt (GFI) circuit breaker is not installed, an electric shock

could occur.

■ Perform the drainage/piping work securely according to the installation manual.

If there is defect in the drainage/piping work, water could drip from the unit, and

damage household items.

■ 'RQRWWRXFKWKHDLULQOHWRUWKHDOXPLQXP¿QVRIWKHRXWGRRUXQLW

This could cause injury.

■ Do not install the outdoor unit where small animals may live.

If small animals enter the unit and damage its electrical parts, it could cause a

PDOIXQFWLRQVPRNHHPLVVLRQRU¿UH.HHSWKHDUHDDURXQGWKHXQLWFOHDQ

CAUTION (Could lead to serious injury when operated incorrectly.)

WARNING (Could lead to death or serious injury.)

ENGLISH

SPLIT-TYPE AIR CONDITIONERS

INSTALLATION MANUAL

(OHFWULFDOVSHFL¿FDWLRQV

MODEL

INDOOR MSZ-GS18NA

MSY-GS18NA

OUTDOOR MUZ-GS18NA(H)

MUY-GS18NA MUZ-GS18NAHZ

INDOOR UNIT

Power supply (V, PHASE, Hz) 208/230, 1, 60

Min. Circuit Ampacity (A) 1.0

Fan motor (F.L.A.) (A) 0.74

OUTDOOR UNIT

Power supply (V, PHASE, Hz) 208/230, 1, 60

Max. Fuse size (time delay) (A) 15 20

Min. Circuit Ampacity (A) 12 18

Fan motor (F.L.A.) (A) 0.93 0.93

Compressor

(R.L.A) (A) MSZ 8.4 13.6

MSY 8.4 -

(L.R.A) (A) MSZ 10.5 17.0

MSY 10.5 -

Control voltage Indoor unit - Remote controller: (Wireless)

Indoor unit - Outdoor unit: DC12-24 V (Polar)

Pipe Outside diameter Minimum wall

thickness

Insulation

thickness Insulation material

inch (mm)

For liquid 1/4 (6.35) 0.0315 (0.8) 5/16 (8) Heat resistant foam

plastic 0.045 Spe-

FL¿FJUDYLW\

For gas 3/8 (9.52) 0.0315 (0.8) 5/16 (8)

1/2 (12.7) 0.0315 (0.8) 5/16 (8)

Limits

Pipe length MSZ/MSY-GS18NA 100 ft. (30 m) max.

Height difference MSZ/MSY-GS18NA 50 ft. (15 m) max.

No. of bends 10 max.

Pipe length

Up to 25 ft. (7.5 m) No additional charge is required.

Exceeding 25 ft. (7.5 m) Additional charge is required.

(Refer to the table below.)

Refrigerant to be

added MSZ/MSY-GS18NA 1.08 oz each 5 ft. (20 g/m)

1-3. SPECIFICATIONS

1-3-1. POWER SUPPLY AND INDOOR/OUTDOOR

WIRE CONNECTION

• Power should be taken from an exclusive branched circuit.

• Wiring work should be based on applicable technical stand-

ards.

• Wiring connections should be made following the diagram.

• Securely tighten screws.

Connecting wires and the ground wire

• Use solid conductor Min. AWG14 or stranded conductor

Min. AWG14.

• Use double insulated copper wire with 600 V insulation.

• Use copper conductors only.

* Follow local electrical codes.

Power supply cable and ground wire

• Use solid or stranded conductor.

MUZ-GS18NA(H)

MUY-GS18NA Min. AWG14

MUZ-GS18NAHZ Min. AWG12

• Use copper conductors only.

* Follow local electrical codes.

Note:

When the indoor unit is powered from the outdoor unit, depend-

ing on local code, a disconnect switch needs to be installed to a

power supply circuit.

1-2. SELECTING THE INSTALLATION LOCATION

INDOOR UNIT

 :KHUHDLUÀRZLVQRWEORFNHG

• Where cool air spreads over the entire room.

• On a rigid wall to reduce the possibility of vibration.

• Where it is not exposed to direct sunlight. Do not ex-

pose to direct sunlight also during the period following

unpacking to before use.

• Where it can be easily drained.

• At a distance 3 ft. (1 m) or more away from a TV and

radio. Operation of the air conditioner may interfere

with radio or TV reception. An amplifier may be re-

quired for the affected device.

• In a place as far away as possible from fluorescent

and incandescent lights. In order to make the infrared

remote control operate the air conditioner normally.

The heat from the lights may cause deformation or the

ultraviolet may cause deterioration.

 :KHUHWKHDLU¿OWHUFDQEHUHPRYHGDQGUHSODFHGHDVLO\

•

Where it is away from the other heat or steam source.

Note:

Install the indoor unit high on the wall where air can dis-

tribute over the entire room.

REMOTE CONTROLLER

• Where it is convenient to operate and easily visible.

• Where children cannot easily touch it.

 6HOHFWDSRVLWLRQDERXWIWPDERYHWKHÀRRU

Check that signals from the remote controller from

that position are received by the indoor unit (‘beep’

or ‘beep beep’ receiving tone sounds). Then, attach

remote controller holder to a pillar or wall and install

wireless remote controller.

Note:

,QURRPVZKHUHLQYHUWHUW\SHÀXRUHVFHQWODPSVDUHXVHG

the signal from the wireless remote controller may not be

received.

OUTDOOR UNIT

• Where it is not overly exposed to strong winds.

 :KHUHDLUÀRZLVJRRGDQGGXVWOHVV

• Where neighbours are not annoyed by operation

sound or hot air.

• Where rigid wall or support is available to prevent the

increase of operation sound or vibration.

• Where there is no risk of combustible gas leakage.

• If installing the unit in a location high above the ground,

be sure to secure the unit legs.

• Where it is at least 10 ft. (3 m) away from the antenna

of TV set or radio. Operation of the air conditioner may

interfere with radio or TV reception in areas where re-

FHSWLRQ LV ZHDN $Q DPSOL¿HU PD\ EH UHTXLUHG IRU WKH

affected device.

• Install the unit horizontally.

• Please install it in an area not affected by snowfall or

blowing snow. In areas with heavy snow, please install

DFDQRS\DSHGHVWDODQGRUEDIÀHERDUGV

Note:

• It is advisable to make a piping loop near outdoor unit

so as to reduce vibration.

 )RU LQFUHDVHG HI¿FLHQF\ LQVWDOO WKH RXWGRRU XQLW LQ D

location where continuous direct sunlight or excessive

water can be avoided as much as possible.

Note:

When operating the air conditioner in low outside tem-

perature, be sure to follow the instructions described

below.

• Never install the outdoor unit in a place where its air

inlet/outlet side may be exposed directly to wind.

• To prevent exposure to wind, install the outdoor

unit with its air inlet side facing the wall and

DEDIÀH

board on the air outlet side.

Avoid the following places for installation where air

conditioner trouble is liable to occur.

 :KHUHÀDPPDEOHJDVFRXOGOHDN

• Where there is an excessive amount of machine oil

in the air.

 :KHUHRLOLVVSODVKHGRUZKHUHWKHDUHDLV¿OOHGZLWK

oily smoke (such as cooking areas and factories,

in which the properties of plastic could be changed

and damaged).

• Salty places such as the seaside.

 :KHUH VXO¿GH JDV LV JHQHUDWHG VXFK DV KRW VSULQJ

sewage, waste water.

•

Where there is high-frequency or wireless equipment.

•

Where there is emission of high levels of VOCs,

including phthalate compounds, formaldehyde, etc.,

which may cause chemical cracking.

1-3-2. REFRIGERANT PIPES

• To prevent condensation, insulate the two refrigerant pipes.

CAUTION

%HVXUHWRXVHWKHLQVXODWLRQRIVSHFL¿HGWKLFNQHVVWDEOHRQ

the right). Excessive insulation may cause incorrect instal-

lation of the indoor unit, and too little insulation may cause

condensate to form.

• Refrigerant pipe bending radius must be 4 in. (100 mm) or

more.

 7KHXQLWKDVÀDUHG FRQQHFWLRQV RQERWKLQGRRUDQGRXWGRRU

sides.

• Remove the valve cover from the outdoor unit, then connect

the pipe.

• Refrigerant pipes are used to connect the indoor and outdoor

units.

• Be careful not to crush or over bend the pipe in pipe bending.

• Refrigerant adjustment... If pipe length exceeds 25 ft. (7.5 m),

additional refrigerant (R410A) charge is required.

(The outdoor unit is charged with refrigerant for pipe length

up to 25 ft. [7.5 m])

• Please carefully consider the indoor unit location when piping

lengths are less than 16 ft. (5 m) as there could be intermit-

tent noises during normal operation that would be noticeable

in very quiet environments.

1-4. INSTALLATION DIAGRAM

ACCESSORIES

Check the following parts before installation.

(1) Installation plate 1

(2)

Attachment screws for the installa-

tion plate

4 × 25 mm

(3) Wireless remote controller 1

(4) Felt tape (For left or left-rear piping) 1

(5) Remote controller holder 1

(6)

Screws for the remote controller

holder

3.5 × 16 mm (Black)

(7) Battery (AAA) for (3) 2

(8) $LUFOHDQLQJ¿OWHU 2

FIELD-SUPPLIED PARTS

(A)

Indoor/outdoor unit connecting wire*1

(B) Extension pipe 1

(D) Wall hole cover 1

(E) Pipe attachment strap 2 to 5

(F) Screw for (E) 4 × 20 mm 2 to 5

(G) Piping tape 1

(H) Putty 1

(I)

Drain hose

(or soft PVC hose, 19/32 in. [15 mm]

inner diameter or hard PVC pipe

VP16)

2 to 5

(J) Refrigerant oil 1

(K) Power supply cord *11

Units should be installed by licensed contractor

according to local code requirements.

Note:

*1 Place indoor/outdoor unit connecting wire (A)

and power supply cord (K) at least 3 ft. (1 m)

away from the TV antenna wire.

Unit: inch

Unit: mm

Drain piping for outdoor unit

Install the unit horizontally.

Do not use drain socket in cold regions. Drain may freeze and make the fan stop.

The outdoor unit produces condensate during the heating operation. Select the installation place to ensure to prevent the outdoor unit and/or the grounds from being wet by drain

water or damaged by frozen drain water.

33-1/16

14-3/4~14-5/8

19-11/16

Air inlet

6-7/8

15-3/8

Air outlet

2-3/8 x 13/16 slot 1-18/32

Air inlet

840

175 500

Air inlet

390

330

349~371

Air outlet

2-10 x 21 slot

Air inlet

Note:

• The dimensions indicated in the arrows ( ) above

show the required space to guarantee performance of

the air conditioner. Install the outdoor unit where the

maximum possible space can be provided, considering

later relocation, services, or repairs.

 7KHFRROLQJKHDWLQJSHUIRUPDQFHDQGWKHHI¿FLHQF\RI

power usage may fall about 10% at the place where

short cycle is likely occur due to poor ventilation. In-

stalling the air outlet guide (optional) can improve per-

formances.

• If air from the outlet blows against the wall, it may

cause stains on the wall.

Do not take in the outlet air

discharged by other units directly.

15-3/4 in. or more

(400 mm or more)

39-3/8 in. or more

(1000 mm or more)

When the piping is to be attached to a wall com-

prised of tin plate or metal netting, use chemically

treated wooden piece 25/32 in. (20 mm) or thicker

between the wall and the piping, or wrap insulation

vinyl tape 7 to 8 turns around the piping.

To use existing piping, perform COOL operation

for 30 minutes and pump down before removing

WKHROGDLUFRQGLWLRQHU5HPDNHÀDUHDFFRUGLQJWR

the dimension for new refrigerant.

4 3/8 in.

(111 mm) or

more / 5 3/16 in.

(132 mm) or more

for left and left

back piping (us-

ing spacer)

3/8 in. (10 mm)

or more

*3 When any 2 sides of left, right and rear of unit are clear

14 in. (350 mm)

or more

4 in. (100 mm)

or more

4 in. (100 mm)

or more

clear *2

20 in. (500 mm) *3

or more

*2 20 in. (500 mm) or more when front

and sides of unit are clear

5 1/4 in.

(133 mm)

or more

6 5/8 in.

(168 mm)

or more

After the leak test, apply insulating material tightly

so that there is no gap.

5.9 ft. to 7.5 ft. (1.8 m to 2.3 m)

IURPWKHÀRRULVUHFRPPHQGHG

Use the wall hole sleeve (C)

to prevent indoor/outdoor

connecting wire (A) from

contacting metal parts in

the wall and to protect the

wiring from rodents.

Indoor unit

Wall hole

sleeve (C)

Cut off the

extra length.

Pipe attachment

strap (E)

Seal the wall hole

gap with putty (H).

Attach the pipe to

wall with pipe at-

tachment strap (E).

Wall hole cover (D)

Attachment

screw (F)

2-1. ATTACHING THE INSTALLATION PLATE

 )LQGDVWXGLQWKHZDOOWRDWWDFKLQVWDOODWLRQSODWHKRUL]RQWDOO\E\WLJKWHQLQJWKH¿[-

LQJVFUHZV¿UPO\

• To prevent installation plate (1) from vibrating, be sure to install the attachment screws

in the holes indicated in the illustration. For added support, additional screws may also

be installed in other holes.

• When the indoor unit is to be attached to a concrete wall using recessed bolts, se-

cure installation plate (1) using 7/16 in. x 13/16 in. · 7/16 in. x 1 in. (11 mm × 20 mm ·

11 mm × 26 mm) oval hole (17-3/4 in. [450 mm] pitch).

 ,IWKHUHFHVVHGEROWLVWRRORQJFKDQJHLWIRUDVKRUWHURQH¿HOGVXSSOLHG

2. INDOOR UNIT INSTALLATION

Wall

Outdoor side

2-2. DRILLING

1) Determine where the holes will be located on the wall.

2) Drill a ø 3 in. (75 mm) hole. The outdoor side should be 6/32 to 9/32 in. (5 to 7 mm)

lower than the indoor side.

3) Insert wall hole sleeve (C).

2-3. CONNECTING WIRES FOR INDOOR UNIT

Note:

When the indoor unit is powered from the outdoor unit, depending on local code, a discon-

nect switch needs to be installed to a power supply circuit.

1) Remove the panel assembly. (Refer to 5-1.)

2) Place the upper part of the indoor unit on the installation plate.

3) Remove corner box R and electrical cover.

4) Remove display panel, conduit cover and conduit plate.

5) Attach conduit pipe (for rear piping) / elbow joint (for right, left, or downward piping) to

conduit plate with lock nut. The thread of the installed conduit pipe / elbow joint appear-

ing inside should be less than 3/8 in. (10 mm). (Fig. 1) Elbow joint should appear less

than 1-3/16 in. (30 mm) outside. (Fig. 2)

6) Process the end of ground wire (Fig. 3). Connect it to the ground terminal of electrical

parts box.

7) Process the end of indoor/outdoor unit connecting wire (A) (Fig. 3). Attach it to the

terminal block. Be careful not to make mis-wiring. Attach the wire to the terminal block

securely so that its core cannot be seen, and no external force affects the connecting

section of the terminal block.

8) Firmly tighten the terminal screws. After tightening, verify that the wires are tightly fas-

tened.

9) Reinstall conduit plate, conduit cover and display panel.

10) According to the piping direction, remove the shaded part of the corner box L (Fig. 4) or

corner box R (Fig. 5). Reinstall electrical cover, corner box and front panel.

Less than 3/8 in.

(10 mm)

Conduit plate

Conduit pipe or

elbow joint

Lock nut

6/32-9/32 in.

(5-7 mm)

Ø 3 in.

(75 mm)

Lead

wire

19/32 in.

(15 mm)

Elbow joint

(for right, left, or downward piping)

Less than 1-3/16 in.

(30 mm)

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

Remark:

* A disconnect switch

should be required.

Check the local code.

** Use a ring tongue termi-

nal in order to connect a

ground wire to terminal.

Conduit plate

• Make ground wire a little longer than

others. (More than 1-9/16 in. [40 mm])

OUTDOOR UNIT

<MUZ-GS18NA(H)>

<MUY-GS18NA>

Power supply

208/230 V AC,

1 phase 2 wires,

60 Hz

INDOOR UNIT

Terminal block

9$&

SKDVH+]

OUTDOOR UNIT

<MUZ-GS18NAHZ>

Terminal

block 1

Ground

Grounding terminal**

Grounding

terminal**

Disconnect

switch*

Grounding terminal**

Terminal block 2

Terminal

block

Installation plate (1)

Center of

ø3 in.(ø75 mm)

hole

6 5/8 in.

(168 mm)

or more

5 1/4 in.

(133 mm)

or more

4 3/8 in. (111 mm) or more

5 3/16 in. (132 mm) or more for left

and left back piping (using spacer)

Ceiling

Wall Wall

Fixing

screw (2)

Insert

the

scale. *

Align the

scale with

the line. *

4 in. (100 mm)

Level

* Same for left hole.

Indoor terminal

block

Fixing screw

Conduit cover

Lock nut

Fixing screw

Conduit plate

Elbow joint

(for right, left, or downward piping)

Electrical cover

Electrical box

Conduit pipe

(for rear piping)

Grounding

terminal

Indoor control

P.C. board holder

• Connect wires to the appropriate terminals

• For future servicing, leave some slack in the connecting wires.

Corner box L

Remove corner box L for

piping on left side of unit.

Remove corner box L for

piping on bottom side of unit.

Corner box R

Remove corner box R for

piping on right side of unit.

Remove corner box R for

piping on bottom side of unit.

2-4-2. DRAIN PIPING

• If the extension drain hose has to pass through a room, be sure to wrap it with insu-

ODWLRQ¿HOGVXSSOLHG

• The drain hose should point downward for easy drain. (Fig. 1)

 ,I WKH GUDLQ KRVH SURYLGHG ZLWK WKH LQGRRU XQLW LV WRR VKRUW FRQQHFW LW ZLWK D ¿HOG

supplied drain hose (I). (Fig. 2)

• When connecting the drain hose to a hard vinyl chloride pipe, be sure to insert it se-

curely into the pipe. (Fig. 3)

Do not make drain piping as shown below.

Do not raise Accumulated

drain water

Air

Waving

Water

leakage

Water

leakage

Water

leakage

Tip of drain

hose dipped

in water

Ditch

At least

1-31/32 in.

(50 mm)

gap

Downward

slope

Drain

hose

Soft hose I.D.

19/32 in.

(15 mm)

Drain hose

Hard vinyl chloride pipe

I.D. 1-3/16 in.

(30 mm)

Insert

securely

Different

diameter joint

27-9/16 in.

(70 cm)

or more

Fig. 1 Fig. 2 Fig. 3

2-4. PIPE FORMING AND DRAIN PIPING

2-4-1. PIPE FORMING

• Place the drain hose below the refrigerant piping.

• Make sure that the drain hose is not crowded or bent.

• Do not pull the hose when applying the tape.

• When the drain hose passes the room, be sure to wrap it with insulation material

¿HOGVXSSOLHG

Note:

Make sure not to damage the cover of refrigerant pipe when attaching it back on with

screws.

Left or left-rear piping

Note:

Be sure to reattach the drain hose and the drain cap if the piping is being installed on

left or bottom left of unit, otherwise, water could drip down from the drain hose.

3ODFHWKHUHIULJHUDQWSLSLQJDQGWKHGUDLQKRVHWRJHWKHUWKHQ¿UPO\DSSO\IHOWWDSH

from the end.

Felt tape (4) overlap width should be 1/3 the tape width. Use a bandage stopper at

the end of felt tape (4).

2) Pull out the drain cap at the back right of the indoor unit. (Fig. 1)

• Hold the convex section at the end and pull the drain cap.

3) Pull out the drain hose at the back left of the indoor unit. (Fig. 2)

• Hold the claw marked by the arrows and pull out the drain hose forward.

4) Put the drain cap into the section to which the drain hose is to be attached at the rear

of the indoor unit. (Fig. 3)

• Insert a screwdriver into the hole on the cap and insert the cap fully into the drain

pan.

5) Insert the drain hose fully into the drain pan at the back right of the indoor unit. (Fig. 4)

• Check if the hose is hooked securely to the projection of its inserting part at the

drain pan.

6) Insert the drain hose into wall hole sleeve (C), and attach the upper part of indoor

unit onto the installation plate (1). Then, shift the indoor unit completely to the left to

make placing the piping in the back of the unit easier.

7) Cut out a piece of cardboard from the shipping box, roll it up, hook it onto the back

rib, and use it as a spacer to lift the indoor unit. (Fig. 5)

8) Connect the refrigerant piping with the extension pipe (B).

9) Attach the lower part of the indoor unit into the installation plate (1).

Remove corner box for

piping on left side of unit.

Drain cap

Drain hose

Drain cap

Drain hose

Fig. 1 Fig. 2

Fig. 3 Fig. 4

Fig. 5

Piping tape (G)

Felt tape (4)

Rear or bottom piping

3ODFHWKHUHIULJHUDQWSLSLQJDQGWKHGUDLQKRVHWRJHWKHUWKHQ¿UPO\DSSO\SLSLQJWDSH

(G) from the end.

2) Insert the piping and the drain hose into the wall hole sleeve (C), and attach the up-

per part of the indoor unit on the installation plate (1).

3) Check if the indoor unit is attached securely on the installation plate (1) by moving

the unit to left and right.

4) Attach the lower part of the indoor unit into the installation plate (1).

Right piping

Note:

Before performing the following, make sure that wiring is completed, and the conduit

cover is installed. (Refer to 2-3.)

1) Place the refrigerant piping and the drain hose together, shift them to left side of the

XQLWDQGWKHQ¿UPO\DSSO\SLSLQJWDSH*IURPWKHHQG

2) Insert the piping and the drain hose into the wall hole sleeve (C), and attach the up-

per part of the indoor unit on the installation plate (1).

3) Check if the indoor unit is attached securely on the installation plate (1) by moving

the unit to left and right.

4) Attach the lower part of the indoor unit into the installation plate (1).

To the left

Remove

corner box

for piping on

right side of

unit

Remove corner box for pip-

ing on bottom side of unit

Liquid pipe

Gas pipe

Felt tape (4)

Indoor/outdoor unit

connecting wire (A)

Piping tape (G)

Do not put the drain pipe directly in a drainage ditch where Ammonia or Sulphuric

gas may be generated. The evaporated corrosive gas may return to the indoor side

through drain pipe and this may cause an unpleasant odor and corrosion on Heat

exchanger may occur.

Indoor unit

connection

Outdoor unit

connection

Copper

pipe

Fig. 1

Good

90°

Tilted

No good

Fig. 2

Uneven Burred

Fig. 4

Clutch type

Flaring tool

Wing nut type

Fig. 5

Flare nut

Die Copper pipe

Smooth all around

Even length all around

Inside is shining without any scratches.

Fig. 6

Flare nut Union joint

External thread sideInternal thread side

7LJKWHQWKHÀDUHQXW

with a torque wrench.

Grip the nut on the

union joint with a spanner.

Burr Copper pipe

Spare reamer

Pipe cutter

Fig. 3

Lead

wire

19/32 in.

(15 mm)

3-1. CONNECTING WIRES FOR OUTDOOR UNIT

1) Remove the service panel.

2) Remove the conduit cover.

3) Attach the conduit connectors to the conduit plate with lock nuts then secure it against unit

with screws.

4) Connect the ground wires of indoor/outdoor unit connecting wire (A) and power supply cord (K)

to the TB support.

5) Loosen the terminal screws, then attach indoor/outdoor unit connecting wire (A) and power

supply cord (K) from the indoor unit correctly to the terminal block. Attach the wires to the

terminal block securely so that the cores cannot be seen, and no external force affects the

connecting section of the terminal block.

6) Firmly tighten the terminal screws. After tightening, verify that the wires are tightly fastened.

7) Install the conduit cover.

8) Install the service panel securely.

3-2. FLARE CONNECTION

1) Cut the copper pipe as straight as possible with a pipe cutter. (Fig. 1, 2)

2) Remove all burrs from the cut section of the pipe, ensuring that precautions are taken to

avoid getting metal shavings into the piping. (Fig. 3)

5HPRYHÀDUHQXWVDWWDFKHGWRLQGRRUDQGRXWGRRUXQLWVWKHQSXWWKHPRQSLSH

4) Flaring work (Fig. 4, 5). Firmly hold copper pipe in the dimension shown in the table. Select A

inch (mm) from the table according to the tool you use.

5) Check

 &RPSDUHWKHÀDUHGZRUNZLWK)LJ

 ,IÀDUHLVGHIHFWLYHFXWRIIWKHVHFWLRQDQGUHSHDWSURFHGXUH

3. OUTDOOR UNIT INSTALLATION

Power supply cord (K)

L1 L2

Pipe diameter

inch (mm)

inch

(mm)

A inch (mm) Tightening torque

Clutch

type tool

for R410A

Clutch

type tool

for R22

Wing nut

type tool

for R22

ft-lb

(kgf•cm) N•m

ø 1/4 (6.35) 21/32

(17)

0 to 0.02

(0 to 0.5)

0.04 to

0.06

(1.0 to

1.5)

0.06 to

0.08

(1.5 to

2.0)

10 to 13

(140 to 180) 13.7 to 17.7

ø 3/8 (9.52) 7/8

(22)

25 to 30

(350 to 420) 34.3 to 41.2

ø 1/2 (12.7) 1-1/32

(26) 0.08 to

0.10

(2.0 to

2.5)

36 to 42

(500 to 575) 49.0 to 56.4

ø 5/8 (15.88)

1-5/32

(29)

54 to 58

(750 to 800) 73.5 to 78.4

• Make ground wire a little longer than others. (More than 3-7/8 in. [100 mm])

• For future servicing, leave some slack in the connecting wires.

• Be sure to attach each screw to its correspondent terminal when securing the

cord and/or the wire to the terminal block.

Service panel

Lock nut

Conduit cover Conduit

plate

Conduit pipe

3-3. PIPE CONNECTION

 )DVWHQÀDUHQXWZLWKDWRUTXHZUHQFKDVVSHFL¿HGLQWKHWDEOHUHIHUWR

 :KHQIDVWHQHGWRRWLJKWÀDUHQXWPD\HYHQWXDOO\EUHDNDQGFDXVHUHIULJHUDQWOHDNDJH

• Be sure to wrap insulation around the piping. Direct contact with the bare piping may

result in burns or frostbite.

Indoor unit connection

Connect both liquid and gas pipings to indoor unit.

 $SSO\DWKLQFRDWRIUHIULJHUDWLRQRLO-RQWKHÀDUHGHQGVRIWKHSLSHV'RQRWDSSO\UH-

frigeration oil on screw threads. Excessive tightening torque will result in damage on the

screw.

 7RFRQQHFW¿UVWDOLJQWKHFHQWHUWKHQWLJKWHQWKH¿UVWWRWXUQVRIÀDUHQXWE\KDQG

• Use tightening torque table above as a guideline for indoor unit side joints, and tighten

XVLQJWZRZUHQFKHV([FHVVLYHWLJKWHQLQJGDPDJHVWKHÀDUHVHFWLRQ

Outdoor unit connection

Connect pipes to stop valve pipe joint of the outdoor unit following the same procedure

detailed in Indoor unit connection.

• For tightening, use a torque wrench or spanner.

3-4. INSULATION AND TAPING

1) Cover piping joints with pipe cover.

2) For outdoor unit side, insulate the piping, including valves.

3) Apply piping tape (G) starting from the connection on the outdoor unit.

• When piping has to be installed through a ceiling, closet or where the temperature and

KXPLGLW\DUHKLJKXVHDGGLWLRQDO¿HOGVXSSOLHGLQVXODWLRQWRSUHYHQWFRQGHQVDWLRQ

WARNING

When installing the unit, securely connect the refrigerant pipes before starting the

compressor.

<MUZ-GS18NA(H)>

<MUY-GS18NA>

Terminal block

to conduit cover

Power supply cord (K)

Indoor/outdoor unit

connecting wire (A)

TB support

Grounding

terminal

<MUZ-GS18NAHZ>

Terminal block

to conduit cover Power supply cord (K)

Indoor/outdoor unit

connecting wire (A)

TB support

Grounding

terminal

4-4. EXPLANATION TO THE USER

• Using the OPERATING INSTRUCTIONS, explain to the user how to use the air condition-

HUWKHUHPRWHFRQWUROOHUUHPRYLQJWKHDLU¿OWHUVSODFLQJRUUHPRYLQJWKHUHPRWHFRQWUROOHU

from the remote controller holder, cleaning methods, precautions for operation, etc.)

• Recommend that the user read the OPERATING INSTRUCTIONS carefully.

4. PURGING PROCEDURES, LEAK TEST, AND TEST RUN

4-2. TEST RUN

1) Insert power supply plug into the power outlet and/or turn on

the breaker.

2) Press the E.O. SW once for COOL, and twice for HEAT (only

MSZ series) operation. Test run will be performed for 30

minutes. If the power lamp blinks every 0.5 seconds, inspect

the indoor/outdoor unit connecting wire (A). After the test

run, emergency COOL mode (75ºF [24ºC] COOL) will start.

3) To stop operation, press the E.O. SW several times until all

LED lamps turn off. Refer to operating instructions for de-

tails.

Checking the remote (infrared) signal reception

Press the ON/OFF button on the remote controller (3) and listen for an audible indicator

from the indoor unit. Press the ON/OFF button again to turn the air conditioner off.

• Once the compressor stops, the restart preventive device operates so the compressor

will not operate for 3 minutes to protect the air conditioner.

4-3. AUTO RESTART FUNCTION

This product is equipped with an auto restart function. When the power supply is cut off

during operation, such as during blackouts, the function automatically starts operation in

the previous setting once the power supply is resumed. (Refer to the operating instructions

for details.)

Emergency

operation switch

(E.O. SW)

Caution:

• After test run or remote signal reception check, turn off the unit with the E.O. SW or

the remote controller before turning off the power supply. If this procedure is not per-

formed, the unit will automatically begin operation when power supply is resumed.

To the user

• After installing the unit, explain to the user about auto restart function.

• If auto restart function is unnecessary, it can be deactivated. Consult the service rep-

resentative to deactivate the function. Refer to the service manual for details.

4-1. PURGING PROCEDURES AND LEAK TEST

Remove service port caps from stop valves on both sides of refrigerant lines. (The stop

valves are fully closed when shipped.) Leave closed.

2) Connect gauge manifold to ports of stop valves.

Stop valve for

GAS

Stop valve cap

(Torque 15 to

22 ft-lb, 19.6 to

29.4 N•m, 200

WRNJIƒFP

Vacuum pump (or the vacuum

pump with the function to

SUHYHQWWKHEDFNÀRZ

Gauge manifold valve

(for R410A)

Compound pressure gauge

(for R410A)

–14.7 psi [Gauge]

(–0.101 Mpa)

Handle

Low Handle High

Adapter for pre-

venting the back

ÀRZ

Charge hose

(for R410A)

Open

Hexagonal wrench

Precautions when using the control valve When attaching the control valve

to the service port, valve core may

deform or loosen if excess pressure

is applied. This may cause gas leak.

Service port

Charge hose

Body

Open

Control valve

When attaching the control valve to

the service port, make sure that the

valve core is in closed position, and

then tighten part A. Do not tighten

part A or turn the body when valve

core is in open position.

Service port cap

(Torque 10 to 13 ft

-Ib, 13.7 to 17.7 N•m,

140 to 180 kgf•cm)

Valve stem (inside)

3) Evacuate the system to 4000 microns from both service valves. System manifold gaug-

es must not be used to measure vacuum. A micron gauge must be used at all times.

Break the vacuum with Nitrogen(N2) into the discharge service valve to 0 PSIG.

4) Evacuate the system to 1500 microns. Break the vacuum with Nitrogen(N2) into the

discharge service valve to 0 PSIG.

5) Evacuate the system to 500 microns.

6) Close gauge manifold valves, stop the pump, and conduct a 30 minute rise test.

7) System should hold 500 microns for a minimum of 1 hour.

8) Fully open the valve stem of all stop valves on both sides of gas pipe and liquid pipe

by the hexagonal wrench. If the valve stem hits the stopper, do not turn it any further.

Operating without fully opening lowers the performance and this causes trouble.

9) Refer to 1-3 and charge the prescribed amount of additional refrigerant if needed. Be

sure to charge slowly with liquid refrigerant. Otherwise composition of the refrigerant in

the system may be changed and affect performance of the air conditioner.

10) Remove gauge manifolds and replace service port caps and tighten.

11) Leak test

Stop valve for LIQUID

Pressure gauge

(for R410A)

5. RELOCATION AND MAINTENANCE

5-1. REMOVING AND INSTALLING THE PANEL

ASSEMBLY

Removal procedure (Fig. 1)

1) Open the front panel.

5HPRYHWKHVFUHZVZKLFK¿[WKHSDQHODVVHPEO\

3) Close the front panel.

5HPRYHWKHSDQHODVVHPEO\%HVXUHWRUHPRYHLWVERWWRPHQG¿UVW

Installation procedure (Fig. 2)

1) Install the panel assembly following the removal procedure in reverse.

2) Be sure to press the positions as indicated by the arrows in order to attach the

assembly completely to the unit.

Fig. 1

Fig. 2

* Do not hold the A part when installing/removing or carrying the panel, or the panel

might be damaged.

A part : lower part of air

outlet of the panel

5-3. PUMPING DOWN

When relocating or disposing of the air conditioner, pump down the system following the procedure below so that refrigerant is not released into the atmosphere.

1) Connect the gauge manifold valve to the service port of the stop valve on the gas pipe side of the outdoor unit.

2) Fully close the stop valve on the liquid pipe side of the outdoor unit.

3) Close the stop valve on the gas pipe side of the outdoor unit almost completely so that it can be easily closed fully when the pressure gauge shows 0 psi [Gauge] (0 Mpa).

4) Start the emergency COOL operation.

To start the emergency operation in COOL mode, disconnect the power supply plug and/or turn off the breaker. After 15 seconds, connect the power supply plug and/or turn

on the breaker, and then press the E.O. SW once. (The emergency COOL operation can be performed continuously for up to 30 minutes.)

Fully close the stop valve on the gas pipe side of the outdoor unit when the pressure gauge shows (0.1 to 0 psi [Gauge] (0.05 to 0 Mpa)).

6) Stop the emergency COOL operation.

To stop operation, press the E.O. SW several times until all LED lamps turn off. Refer to operating instructions for details.

5-2. REMOVING THE INDOOR UNIT

Remove the bottom of the indoor unit from the installation plate.

When releasing the corner part, release both left and right bottom corner part of

LQGRRUXQLWDQGSXOOLWGRZQZDUGDQGIRUZDUGDVVKRZQLQWKH¿JXUHRQWKHULJKW

HEAD OFFICE: TOKYO BUILDING, 2-7-3, MARUNOUCHI, CHIYODA-KU,

TOKYO 100-8310, JAPAN

6. CONNECTING THE INTERFACE/CONNECTOR CABLE TO THE AIR CONDITIONER

Fix the connecting cable at the prescribed position securely. Incorrect installa-

WLRQPD\FDXVHHOHFWULFVKRFN¿UHDQGRUPDOIXQFWLRQ

WARNING

• Connect the INTERFACE/CONNECTOR CABLE to the Indoor electronic control P.C. board of the air conditioner with the connecting cable.

• Cutting or extending the connecting cable of the INTERFACE/CONNECTOR CABLE results in defects in connecting.

Do not bundle the connecting cable together with power supply cord, indoor/outdoor connecting wire, and/or earth wire. Keep as much distance as possible between the

connecting cable and those wires.

• The thin part of the connecting cable should be stored and placed where customers cannot touch it.

Connecting

Indoor control

P.C. board holder

(1) Remove the panel and the lower right corner box.

(2) Open the indoor control P.C. board holder 90 degrees and remove it.

(3) Join the connecting cable to CN105 on the indoor control P.C. board.

(4) Attach the cable clamp provided with the interface to the thick part of the connecting cable with

DVFUHZîDVVKRZQLQWKH¿JXUH

+RRNWKHFRQQHFWLQJFDEOHLQWRWKHULEVDVVKRZQLQWKH¿JXUH

(6) Install the indoor control P.C. board holder and then stow the extra connecting cable where

LQGLFDWHGLQWKH¿JXUH,QVWDOOWKHORZHUULJKWFRUQHUER[DQGWKHSDQHOWRWKHRULJLQDOSRVLWLRQ

Connector

Interface unit

Thick part of the connecting cable

Air conditioner

Thin part of the connecting cable.

Place this part where customers cannot touch it.

Indoor control P.C.

board CN105

When the refrigeration circuit has a leak, do not execute pump down with the compressor.

When pumping down the refrigerant, stop the compressor before disconnecting the refrigerant pipes. The compressor may burst if air etc. get into it.

WARNING

Mitsubishi Electric MSZ-GS18NA-U1 GS-Series 18k BTU Wall Mounted Unit Manuel utilisateur

Marque: Mitsubishi Electric

Modèle: MSZ-GS18NA-U1 GS-Series 18k BTU Wall Mounted Unit

Catégorie: Climatiseurs split-system

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Mitsubishi Electric MSZ-GS18NA-U1 GS-Series 18k BTU Wall Mounted Unit User manual

Mitsubishi Electric MSZ-GS18NA-U1 GS-Series 18k BTU Wall Mounted Unit Manuel utilisateur

Mitsubishi Electric MSZ-GS18NA-U1 GS-Series 18k BTU Wall Mounted Unit Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents