Morningstar SunSaver Duo Manuel utilisateur

DUAL BATTERY CHARGING SOLAR CONTROLLER

FOR RVS, CARAVANS, AND BOATS

RÉGULATEUR DE CHARGE SOLAIRE POUR DEUX BATTERIES

POUR CAMPING-CARS, CARAVANES ET BATEAUX

SOLARLADEREGLER FÜR ZWEI BATTERIEN

FÜR WOHNMOBILE, WOHNWAGEN UND BOOTE

REGULADOR SOLAR DE CARGA DUAL

PARA VEHÍCULOS RECREATIVOS, AUTOCARAVANAS Y BARCOS

SOLAR CONTROLLER

S

UN

S

AVER

D

UO

TM

For a more detailed manual, please see our website.

Pour une version plus détaillée s’il vous plaît consulter notre site Web.

Für eine detailliertere Version finden Sie auf unserer Website.

Para obtener una versión más detallada por favor visite nuestro sitio web.

InstallatIon and operatIon Manual ...2

Manuel d’InstallatIon et d’utIlIsatIon ...20

BedIenungs- und InstallatIonsanleItung ...38

Manual de InstalacIón y operacIón ...58

www.morningstarcorp.com

2

SUNSAVER DUO DIMENSIONS

1.36

34.52

6.65

168.78

6.10

154.94

2.17

55.12

1.00

25.4

0.28

7.24

inches (mm)

Ratings

• Nominal Voltage 12 Volts

• Rated Solar Current 25 Amps

ENGLISH

3

IMPORTANT SAFETY INFORMATION

SAVE THESE INSTRUCTIONS:

This manual contains important safety, installation and operating

instructions for the SunSaver Duo solar controller.

The following symbols are used throughout this manual to indicate

potentially dangerous conditions or important safety instructions.

WARNING: Indicates a potentially dangerous condition.

Use extreme caution when performing this task.

CAUTION: Indicates a critical procedure for safe and proper

operation of the controller.

NOTE: Indicates a procedure or function that is important for

the safe and proper operation of the controller.

The major features of the SunSaver Duo are shown in figure 1 below.

An explanation of each feature is provided.

6

The major features of the SunSaver Duo are shown in figure 1 below. An explanation of

each feature is provided.

Figure 1. SunSaver Duo features

R em ote Tem peratu re Sensor (RTS) T e rm inals

A connection point for a Morningstar RTS (optional) to remotely monitor battery

temperature.

Local Tem peratu re Sensor

Measures ambient temperature. Battery regulation is adjusted accordingly.

Status LED Indicato r

Provides system status and error indication.

Settings DIP Sw itches

Adjustment switches that define the operating parameters of the SunSaver Duo.

B atte ry #1 P o w e r T e rm inals

Power connections for battery #1.

Sola r Input P o w e r T e rm inals

Power connections for solar module(s).

B atte ry #2 P o w e r T e rm inals

Power wire connections for battery #2.

R em ote M ete r C onnection (R J-11)

A communication port for the Morningstar Remote Meter.

Figure 1. SunSaver Duo features

Remote Temperature Sensor (RTS) Terminals

A connection point for a Morningstar RTS (optional) to remotely monitor

battery temperature.

4

Local Temperature Sensor

Measures ambient temperature. Battery regulation is adjusted

accordingly.

Status LED Indicator

Provides system status and error indication.

Settings DIP Switches

Adjustment switches that define the operating parameters of the

SunSaver Duo.

Battery #1 Power Terminals

Power connections for battery #1.

Solar Input Power Terminals

Power connections for solar module(s).

Battery #2 Power Terminals

Power wire connections for battery #2.

Remote Meter Connection (RJ-11)

A communication port for the Morningstar Remote Meter.

Morningstar Accessories

Remote Temperature Sensor (Model: RTS)

The RTS measures battery temperature for accurate temperature com

-

pensation. Use when the ambient battery temperature differs from the

ambient controller temperature by +/– 5 degrees C or more.

Remote Meter (Model: RM-1)

The digital Remote Meter displays system operating information, error

indications, and self-diagnostic read-out.

PC MeterBus Adapter (Model: MSC)

The MSC converts the MeterBus RJ-11 electrical interface to a standard

RS-232 interface which allows communication between the SunSaver

Duo and a PC. The MSC is required for programming custom charging

setpoints and for logging data. Visit Morningstar’s website for more

information.

INSTALLATION

General Installation Notes

• Read through the entire installation section before beginning

installation.

• Be very careful when working with batteries. Wear eye protection.

Have fresh water available to wash and clean any contact with

battery acid.

• Use insulated tools and avoid placing metal objects near the

batteries.

• Explosive battery gasses may be present during charging. Be certain

there is sufficient ventilation to release the gasses.

• Do not install in locations where water can enter the controller.

• Loose power connections and/or corroded wires can melt wire

insulation, burn surrounding materials, or even cause fire. Ensure

tight connections and use cable clamps to secure cables in mobile

applications.

• Only charge lead-acid batteries.

• Each of the two SunSaver Duo Battery connections may be wired to

one battery or a bank of batteries. The following instructions refer to

a singular battery, but it shall be implied that each battery connection

can be made to either one battery or a group of batteries wired in

parallel to form a 12 volt battery bank.

Adjusting DIP Switches

9

3.2 Adjusting DIP Switches

Figure 2. Setting DIP switch definitions

DIP Sw itches 1 & 2 – B atte ry Type S elect

The SunSaver Duo charges both sealed and flooded lead-acid batteries per the

charging specifications in table 1 below. Sealed batteries are typically

maintenance-free batteries that do not require water. Flooded batteries have

removable caps that allow the addition of water when needed. DIP switches 1 &

2 select the battery type for Battery #1 and Battery #2 respectively. Choose the

correct battery type for each battery.

DIP Switch OFF: Sealed battery type (factory pre-set)

DIP Switch ON: Flooded battery type

B atte ry Type

Setpoint

Sealed Flooded

Absorption Voltage 14.1 V 14.4 V

Float Voltage 13.7 V 13.7 V

Boost Voltage X 14.8 V

Boost Time X 2 hrs

Boost Interval X 28 days

Table 1. Standard battery charging programs

DIP Sw itch 3 – B attery C harging P rio rity

Select the percentage of available charge current to each battery.

Figure 2. Setting DIP switch definitions

ENGLISH

5

6

DIP Switches 1 & 2 – Battery Type Select

The SunSaver Duo charges both sealed and flooded lead-acid batteries

per the charging specifications in table 1 below.

DIP Switch OFF: Sealed battery type (factory pre-set)

DIP Switch ON: Flooded battery type

BATTERY TYPE

Setpoint Sealed Flooded

Absorption Voltage 14.1 V 14.4 V

Float Voltage 13.7 V 13.7 V

Boost Voltage X 14.8 V

Boost Time X 2 hrs

Boost Interval X 28 days

Table 1. Standard battery charging programs

DIP Switch 3 – Battery Charging Priority

Select the percentage of available charge current to each battery.

DIP Switch 3 OFF: 90% / 10% Priority (factory pre-set)

DIP Switch 3 ON: 50% / 50% Priority

DIP Switch 4 – Custom Setpoints

If the standard battery type settings are not suitable, custom charging

setpoints can be programmed using a PC and a Morningstar Serial to

Meterbus adapter (not included). See Morningstar’s website for more

information.

DIP Switch 4 OFF: Factory settings (factory pre-set)

DIP Switch 4 ON: Custom programmed settings

DIP Switch 5 – Regulation Type

The SunSaver Duo is a PWM charge controller. Some systems with

sensitive equipment may experience noise interference from PWM

charging. Refer to the FAQ in Troubleshooting for tips on how to

reduce or eliminate PWM noise.

If the noise cannot be satisfactorily reduced, place DIP switch 5 in

the ON position. While less efficient, Slow Switching regulation will

significantly reduce or eliminate PWM noise.

DIP Switch 5 OFF: PWM Regulation (factory pre-set)

DIP Switch 5 ON: Slow Switching Regulation

ENGLISH

7

Mounting

NOTE: When mounting the SunSaver Duo, ensure free air

flow through the controller heat sink fins. There should be

at least 3 inches (75 mm) clearance above and below the

controller to allow for cooling. If mounted in an enclosure,

ventilation is highly recommended.

WARNING: Never install the SunSaver Duo in a sealed

enclosure with vented (flooded) batteries! Do not install in

a confined area where battery gasses can accumulate.

RISK OF EXPLOSION!

1. Locate the SunSaver Duo on a vertical surface protected from direct

sun, high temperatures, and water.

2. Place the SunSaver Duo in the location where it will be mounted.

Verify that there is sufficient room to run wires and that there is

ample room above and below the controller for air flow.

11

3.3 M ounting

NO TE: When mounting the SunSaver Duo, ensure free air flow through the controller

heat sink fins. There should be at least 3 inches (75 mm) clearance above and below

the controller to allow for cooling. If mounted in an enclosure, ventilation is highly

recommended.

W ARNING: Never install the SunSaver Duo in a sealed enclosure with vented

(flooded) batteries! Do not install in a confined area where battery gasses can

accumulate. Risk of explosion!

1. Locate the SunSaver Duo on a vertical surface protected from direct sun, high

temperatures, and water.

2. Place the SunSaver Duo in the location where it will be mounted. Verify that

there is sufficient room to run wires and that there is ample room above and

below the controller for air flow.

Figure 3. Mounting and cooling

3. Use a pencil or pen to mark the four (4) mounting hole locations on the mounting

surface.

4. Remove the controller and drill 3/32” (2.5 mm) holes in the marked locations.

5. Place the controller on the surface and align the mounting holes with the drilled

holes in step 4. Secure the controller in place using the mounting screws

(included).

Figure 3. Mounting and cooling

3. Use a pencil or pen to mark the four (4) mounting hole locations on

the mounting surface.

4. Remove the controller and drill 3/32” (2.5 mm) holes in the marked

locations.

5. Place the controller on the surface and align the mounting holes with

the drilled holes in step 4. Secure the controller in place using the

mounting screws (included).

8

Wiring

Three system wiring examples are provided for RV’s and caravans,

boats, and non-mobile installations. Reference the appropriate wiring

diagram for your installation.

CAUTION: Protect system wiring from sharp edges and foot

traffic. Use grommets and wire loom where necessary.

NOTE: Power connection order is not critical. A connection

order has been provided for each installation type for

instructional purposes only.

NOTE: Wiring charts on page 17 of this manual provide

minimum recommended wire size.

RV / CARAVAN INSTALLATION

A wire jumper is installed across the Remote Temperature

Sensor (RTS) terminals at the factory. The jumper can

prevent false RTS detection due to condensation on the

SunSaver Duo. Do not remove this jumper unless an

optional RTS is to be installed.

12

3.4 Wiring

Three system wiring examples are provided for RV’s and caravans, boats, and non-

mobile installations. Reference the appropriate wiring diagram for your installation.

CAUTION: Protect system wiring from sharp edges and foot traffic. Use grommets and

wire loom where necessary.

NO TE: Power connection order is not critical. A connection order has been provided

for each installation type for instructional purposes only.

NO TE: Wiring charts on the back page of this manual provide minimum

recommended wire size.

RV / CARAVAN INSTA LLATION

Figure 4. Typical RV / Caravan wiring diagram

NO TE:To ensure good vehicle chassis ground connections:

- remove all paint, grease, debris at grounding point.

- use sandpaper/emory cloth to expose chassis bare metal.

- use ring terminal and star- or lock-washer to secure cable.

- dielectric grease can be used to minimize corrosion.

Before proceeding, mount the solar module(s) per the manufacturer’s instructions. If

adding batteries that are not factory installed, they should be safely secured in their

desired location. The SunSaver Duo should be mounted per the instructions in section

2.3 M ounting.

Figure 4. Typical RV / Caravan wiring diagram

ENGLISH

9

NOTE: To ensure good vehicle chassis ground connections:

• remove all paint, grease, debris at grounding point.

• use sandpaper/emery cloth to expose chassis bare metal.

• use ring terminal and star- or lock-washer to secure cable.

• dielectric grease can be used to minimize corrosion.

Before proceeding, mount the solar module(s) per the manufacturer’s

instructions. If adding batteries that are not factory installed, they

should be safely secured in their desired location. The SunSaver Duo

should be mounted per the instructions in section Mounting.

Step 1: Ground SunSaver Duo

Ground a negative terminal of the SunSaver Duo to the vehicle

chassis. The SunSaver Duo has a common negative; it does not matter

which negative terminal is grounded. Use wire with black insulation,

appropriately sized for the system charging current (see page 17).

Step 2: Battery #1 (“house” battery bank)

Connect Battery #1 to the SunSaver Duo as shown in figure 4. In RV

installations, Battery #1 should be the “house” or cabin battery.

If the cabin battery was factory installed, battery negative should

already be grounded to the vehicle chassis. Use a short piece of black

wire to ground the cabin battery if necessary. Use red wire for battery

positive. Use wire appropriately sized for the system charging current

(see back page).

An in-line fuse holder should be wired in the positive line no further

than 12” (305 mm) from the battery post. Do not insert a fuse in the

fuse holder at this time.

Step 3: Battery #2 (engine battery)

Connect Battery #2 to the SunSaver Duo as shown in figure 4. The

engine battery should already be grounded to the vehicle chassis. Use

red wire for battery positive. Use wire appropriately sized for the system

charging current (see page 17).

An in-line fuse holder should be wired in the positive line no further

than 12” (305 mm) from the battery post. Do not insert a fuse in the

fuse holder at this time.

Step 4: Solar

Ground the solar module(s) to the vehicle chassis with black wire.

Multiple 12V nominal solar modules may be wired together in parallel

and grounded with one wire. Use red wire for the solar positive connec

-

tion to the SunSaver Duo. Use wire appropriately sized for the system

charging current (see page 17).

10

Confirm that the solar modules are wired for 12V nominal output before

connecting them to the SunSaver Duo. In full sun, the output voltage of

the solar modules should be 18 – 25 Volts before connection to the

SunSaver Duo.

Upon connection of the Solar positive wire, the SunSaver Duo should

begin the start-up sequence, flashing the Status LED 3 times.

Step 5: Remote Temperature Sensor (optional)

An optional Remote Temperature Sensor (purchased separately) mea

-

sures the temperature directly at the battery for more accurate battery

charging. Remove the wire jumper from the RTS terminals before install

-

ing the sensor. The RTS includes full installation instructions.

Step 6: Insert Fuses

Insert a 30 A dc-rated fuse into the fuse holder in each of the battery

positive wires. If the solar module(s) is in full sun, charging should begin.

BOAT INSTALLATION

A wire jumper is installed across the Remote Temperature

Sensor (RTS) terminals at the factory. The jumper can

prevent false RTS detection due to condensation on the

SunSaver Duo. Do not remove this jumper unless an

optional RTS is to be installed.

WARNING: Only ground the DC system to battery negative

(one-point ground). Never ground the DC system to the boat

bonding system or to any metallic part, fixture, or component

on the boat.

NOTE:

An existing common ground wire may connect the

negative battery terminals of two or more on-board batteries.

This cable will not interfere with the SunSaver Duo operation.

ENGLISH

11

14

BOAT IN STA LLATION

W ARNING: Only ground the DC system to battery negative (one-point ground). Never

ground the DC system to the boat bonding system or to any metallic part, fixture, or

component on the boat.

NO TE: An existing common ground wire may connect the negative battery terminals

of two or more on-board batteries. This cable will not interfere with the SunSaver Duo

operation.

Figure 5. Typical boat wiring diagram

Before proceeding :

x Install the solar module(s) per the manufacturer’s instructions.

x Batteries should be installed per the U.S Coast Guard regulations for

pleasureboats. The batteries must be secured to prevent movement and the

battery terminals covered to prevent arcing. A battery box to contain any

spilled battery acid is strongly recommended.

x The SunSaver Duo should be mounted per the instructions in section 2.3

M ounting.

Step 1: B atte ry # 1 (“house” batte ry bank)

Wire the negative terminal of the “house” battery to the negative B attery 1

terminal on the SunSaver Duo with black wire as shown in figure 5. Wire the

“house” battery positive power cable as shown in figure 5. Wire a DC-rated in-line

fuse holder in the cable. The length of cable between the Battery (+) post and in-

line fuse holder should be no longer than 12” ( 305 mm ). Use wire with red

Figure 5. Typical boat wiring diagram

Before proceeding:

• Install the solar module(s) per the manufacturer’s instructions.

• Batteries should be installed per the U.S Coast Guard regulations for

pleasureboats. The batteries must be secured to prevent movement

and the battery terminals covered to prevent arcing. A battery box to

contain any spilled battery acid is strongly recommended.

• The SunSaver Duo should be mounted per the instructions in section

Mounting.

Step 1: Battery # 1 (“house” battery bank)

Wire the negative terminal of the “house” battery to the negative

Battery 1 terminal on the SunSaver Duo with black wire as shown in

figure 5. Wire the “house” battery positive power cable as shown in

figure 5. Wire a DC-rated in-line fuse holder in the cable. The length of

cable between the Battery (+) post and in-line fuse holder should be no

longer than 12” ( 305 mm ). Use wire with red insulation, appropriately

sized for the system charging current (see back page). Do not insert

a fuse in the fuse holder at this time.

Step 2: Battery # 2 (“house” battery)

Wire the negative terminal of the engine battery to the negative

Battery 1 terminal on the SunSaver Duo with black wire as shown in

figure 5. Wire the engine battery positive power cable as shown in fig-

ure 5. Wire a DC-rated in-line fuse holder in the cable. The length of

cable between the Battery (+) post and in-line fuse holder should be

no longer than 12” (305 mm). Use wire with red insulation, appropri-

ately sized for the system charging current. Do not insert a fuse in

the fuse holder at this time.

12

Step 3: Solar

Connect the solar module(s) output to the Solar input connection of the

SunSaver Duo. Multiple 12V nominal modules may be wired together in

parallel and wired to the SunSaver Duo with one pair of wires. Use red

wire for solar positive and black wire for solar negative.

Confirm that the modules are wired for 12V nominal output before

connecting them to the SunSaver Duo. Double-check polarity before

connection. In full sun, the output voltage of the solar modules should

be 18 – 25 Volts before connection to the SunSaver Duo.

Upon connection of the solar positive wire, the SunSaver Duo should

begin the start-up sequence, flashing the Status LED 3 times.

Step 4: Remote Temperature Sensor (optional)

An optional Remote Temperature Sensor (purchased separately) mea

-

sures the temperature directly at the battery for more accurate battery

charging. Remove the wire jumper from the RTS terminals before install

-

ing the sensor. The RTS includes full installation instructions.

Step 5: Insert Fuses

Insert a 30 A dc-rated fuse into the fuse holder in each of the battery

positive wires. If the solar module(s) is in full sun, charging should begin.

NON-MOBILE / PERMANENT DWELLING INSTALLATION

A wire jumper is installed across the Remote Temperature

Sensor (RTS) terminals at the factory. The jumper can

prevent false RTS detection due to condensation on the

SunSaver Duo. Do not remove this jumper unless an

optional RTS is to be installed.

16

NON-MOBILE / PERMANENT DWELLING INSTALLATION

+

-

+

-

+

-

Battery

#2

Battery

#1

30A Fuse 30A Fuse

Solar PV

Array

Earth

Ground

Earth

Ground

Earth

Ground

Figure 6. Terrestrial wiring diagram

NOTE: Earth grounding is recommended but not required. Grounding helps protect

against lightning by providing a direct path to earth. In areas prone to frequent

lightning strikes, external lightning arrestors and/or other means of protection may be

needed.

NOTE: If a Remote temperature Sensor (RTS) is not used, inserting a jumper across

the RTS terminals can prevent false RTS detection due to condensation

on the

SunSaver Duo. Secure a short piece of wire across the RTS terminals.

Step 1: Battery #1

Connect Battery #1 to the SunSaver Duo as shown in figure 6. If charging priority

is set to the default 90% / 10% setting, battery 1 will receive 90% priority. Use red

wire for battery positive and black for battery negative. An in-line fuse holder

should be wired in the positive line no further 12” ( 305 mm ) from the battery

post. Earth ground the battery negative post if desired using a short piece of

black wire appropriately sized for the system charging current (see back page).

Do not insert a fuse in the fuse holder at this time.

Step 3: Battery #2

Connect Battery #2 to the SunSaver Duo as shown in figure 6. Use red wire for

battery positive and black for battery negative. An in-line fuse holder should be

wired in the positive line no further 12” ( 305 mm ) from the battery post. Earth

ground the battery negative post if desired using a short piece of black wire

appropriately sized for the system charging current (see back page). Do not

insert a fuse in the fuse holder at this time.

Figure 6. Terrestrial wiring diagram

ENGLISH

1313

NOTE: Earth grounding is recommended but not required.

Grounding helps protect against lightning by providing a

direct path to earth. In areas prone to frequent lightning

strikes, external lightning arrestors and/or other means of

protection may be needed.

Step 1: Battery #1

Connect Battery #1 to the SunSaver Duo as shown in figure 6. If

charging priority is set to the default 90% / 10% setting, battery 1

will receive 90% priority. Use red wire for battery positive and black for

battery negative. An in-line fuse holder should be wired in the positive

line no further 12” ( 305 mm ) from the battery post. Earth ground the

battery negative post if desired using a short piece of black wire appro

-

priately sized for the system charging current (see back page). Do not

insert a fuse in the fuse holder at this time.

Step 2: Battery #2

Connect Battery #2 to the SunSaver Duo as shown in figure 6. Use red

wire for battery positive and black for battery negative. An in-line fuse

holder should be wired in the positive line no further 12” (305 mm) from

the battery post. Earth ground the battery negative post if desired using a

short piece of black wire appropriately sized for the system charging cur

-

rent (see page 17). Do not insert a fuse in the fuse holder at this time.

Step 3: Solar

Connect the solar module(s) output to the Solar input connection of the

SunSaver Duo. Multiple 12V nominal modules may be wired together in

parallel and wired to the SunSaver Duo with one pair of wires. Use

appropriately sized red wire for solar positive and black wire for solar

negative.

Confirm that the modules are wired for 12V nominal output before con

-

necting them to the SunSaver Duo. Double-check polarity before con-

nection. In full sun, the output voltage of the solar modules should be

18 – 25 Volts before connection to the SunSaver Duo.

Upon connection of the Solar positive wire, the SunSaver Duo should

begin the start-up sequence, flashing the Status LED 3 times.

Earth ground solar negative if desired using a short piece of black wire

appropriately sized for the system charging current (see page 17).

Do not insert a fuse in the fuse holder at this time.

Step 4: Remote Temperature Sensor (optional)

An optional Remote Temperature Sensor (purchased separately) mea

-

sures the temperature directly at the battery for more accurate battery

charging. Remove the wire jumper from the RTS terminals before install

-

ing the sensor. The RTS includes full installation instructions.

14

Step 5: Insert Fuses

Insert a 30 A dc-rated fuse into the fuse holder in each of the battery

positive wires. If the solar module(s) is in full sun, charging should begin.

OPERATION

LED Indications

The Status LED indicates system operational state and any existing

error conditions. Table 1 below defines the Status LED indications.

Status LED Operating State

Off: 5 second

heartbeat

1

Night

Green: on solid

(5 second

heartbeat

2

)

Bulk Charging

Green: Flashing

3

Absorption, Float, or Equalize

Red: Flashing Error

Red: On solid

(5 second

heartbeat

2

)

Critical Error

Table 1. Status LED definitions

1

heartbeat indication flickers the Status LED on briefly every 5 seconds

2

heartbeat indication flickers the Status LED off briefly every 5 seconds

3

Battery 1 and Battery 2 must both be in regulation

Red (flashing) Errors

• reverse polarity battery connection.

• reverse polarity solar connection.

• solar over-current condition.

• high temperature.

• damaged or disconnected Remote Temperature Sensor.

• high voltage disconnect.

Red (on solid) Critical Errors

• damaged local temperature sensor.

• damaged heatsink temperature sensor.

For more information on errors, see Protections section.

ENGLISH

15

Charging Information

19

4.2 Charging Information

The SunSaver Duo is an advanced, fully automatic solar battery charger. No

adjustments are required except to select the battery type at installation. Each battery is

charged independently. The SunSaver Duo has a 4-stage charging algorithm as shown

in figure 7.

NIGHT

1

BULK

CHARGE

2

ABSORPTION

3

FLOAT

TIME

VOLTAGE

4

BOOST

Figure 7. SunSaver Duo charging algorithm

1. Bulk Charge – Recharging with 100% of available solar energy.

2. Absorption – PWM constant-voltage regulation to prevent heating and

excessive battery gassing. Pulse charging to restore full battery capacity.

3. Float – After battery is fully charged, SunSaver Duo reduces to a float or “trickle

charge”.

4. Boost (Flooded battery type only – Every 28 days) – A boost charge for flooded

batteries, bringing uneven cell voltages into balance and extending battery life.

Sometimes called an equalization charge.

NOTE: A 15V maximum battery voltage limit prevents damage to sensitive DC loads.

Figure 7. SunSaver Duo charging algorithm

1. Bulk Charge – Recharging with 100% of available solar energy.

2. Absorption – PWM constant-voltage regulation to prevent heating

and excessive battery gassing. Pulse charging to restore full battery

capacity.

3. Float – After battery is fully charged, SunSaver Duo reduces to a float

or “trickle charge”.

4. Boost (Flooded battery type only – Every 28 days) – A boost charge

for flooded batteries, bringing uneven cell voltages into balance and

extending battery life. Sometimes called an equalization charge.

NOTE: A 15V maximum battery voltage limit prevents

damage to sensitive DC loads.

Protections

Over-current – Solar charge current exceeds the current rating of the

SunSaver Duo. Automatically reconnects in 30 seconds.

CAUTION: A mis-wired connection of a battery to the Solar

input when a second battery is already connected to a

Battery input may damage the SunSaver Duo.

High Temperature – The heatsink temperature is above safe limits.

Automatically reconnects when heatsink cools to a safe temperature.

Short Circuit – Solar input power wires are short-circuited. Charging

automatically resumes when the error is cleared.

Battery Reverse Polarity – Battery 1 or Battery 2 power connections

are connected backwards. Error clears when the mis-wire is corrected.

16

Damaged Local Temperature Sensor – The local ambient temperature

sensor is short-circuited or damaged. Charging stops to avoid over- or

under-charging. This is a critical error.

Damaged Internal Temperature Sensor – The internal heatsink tem

-

perature sensor reading is damaged. This is a critical error.

Remote Temperature Sensor (RTS) – A bad RTS connection or

severed RTS lead has disconnected the temperature sensor during

charging. Charging automatically resumes when the problem is fixed.

To resume operation without an RTS, disconnect all power to the

SunSaver Duo and then reconnect.

High Voltage Transients – Battery 1, Battery 2, and Solar input power

connections are protected against high voltage transients. In lightning

prone areas, additional external suppression is recommended.

Inspection and Maintenance

The following inspections and maintenance tasks are recommended at

least two times per year for best controller performance.

• Tighten all terminals. Inspect for loose, broken, or corroded

connections.

• Verify all wire clamps and tie-downs are secure.

• Check that the controller is mounted in a clean protected

environment free of dirt, insects, nests, and corrosion.

• Check enclosure ventilation and air flow holes for obstructions

if applicable.

• Verify LED indication is consistent with the system conditions at

that time.

• Verify that the Remote Temperature Sensor (if used) is securely

attached to the battery.

TECHNICAL SPECIFICATIONS

ELECTRICAL

• Nominal system voltage .............. 12 V

• Max. solar current ........................ 25 A

• Battery voltage range .................. 1 V – 15 V

• Max. solar voltage ........................ 30 V

• Self-consumption .......................... 5.5 mA (night)

10.0 mA (charging)

• Accuracy

Voltage ............................................ 1.0 %

Current ............................................ 2.0 %

ENGLISH

17

• Meterbus Connection ................... 6-pin RJ-11

• Transient Surge Protection .......... 1500 Watts, all power connections

BATTERY CHARGING

• Regulation Method ....................... 300 Hz PWM or

Slow Switching (10 Hz max.)

•

Temp. Compensation Coefficient

.. –30 mV / °C (25°C reference)

• Temp. Compensation Range ........ –30°C to + 60°C

• Temp. Compensated Setpoints ... Absorption, Float, Equalize

BATTERY SETPOINTS

Sealed Flooded

• Absorption .................................... 14.1 V 14.4 V

• Float ............................................... 13.7 V 13.7 V

• Time until Float ............................. 1 hr 1 hr

• Equalize ......................................... N/A 14.8 V

• Equalize Calendar ......................... N/A 28 days

• Maximum Regulation .................... 15.0 V 15.0 V

• High Voltage Disconnect ............. 15.5 V 15.5 V

• High Voltage Reconnect .............. 14.0 V 14.0 V

MECHANICAL

• Power terminals wire size (max.)

Solid ................................................ #6 AWG / 16 mm

2

Multistrand ...................................... #6 AWG / 16 mm

2

Fine strand ...................................... #8 AWG / 10 mm

2

Terminal Diameter ........................... 0.210 in / 5.4 mm

• Power terminals torque (max.) .... 35 in-lb / 4 Nm

• RTS terminals wire size (max.)

Wire gauge (min)............................. #22 AWG / 0.3 mm

2

Wire gauge (max) ............................ #12 AWG / 3.0 mm

2

• RTS terminals torque (max.) ........ 0.4 Nm / 3.5 in-lb

• Dimensions ....................................

see page 17

ENVIRONMENTAL

• Operating temperature ................ –40°C to +45°C

• Storage temperature .................... –40°C to +85°C

• Humidity ........................................ 100% N.C.

18

Minimum Recommended Wire Gauge

Solar

Amps

One Way Wire Distance (feet)

Wire Gauge (AWG)

14 12 10 8 6

2 70 112 180 287 456

4 35 56 90 143 228

8 18 28 45 72 114

12 12 19 30 48 76

16 9 14 23 36 57

20 7 11 18 29 46

25 6 9 14 23 36

3% Voltage drop, Annealed Copper Wire at 20°C

One-way wire distance: Solar  SunSaver Duo or

SunSaver Duo  Battery

Solar

Amps

One Way Wire Distance (meters)

Wire Gauge (mm

2

)

2.0 3.0 5.0 8.0 13.0

2 21.3 34.1 54.9 87.5 139.0

4 10.7 17.1 27.4 43.6 69.5

8 5.5 8.5 13.7 21.9 34.7

12 3.7 5.8 9.1 14.6 23.2

16 2.7 4.3 7.0 11.0 17.4

20 2.1 3.4 5.5 8.8 14.0

25 1.8 2.7 4.3 7.0 11.0

3% Voltage drop, Annealed Copper Wire at 20°C

One-way wire distance: Solar  SunSaver Duo or

SunSaver Duo  Battery

Specifications subject to change without notice.

Designed in the U.S.A.

Assembled in Taiwan

20

DIMENSIONS DU SUNSAVER DUO

1.36

34.52

6.65

168.78

6.10

154.94

2.17

55.12

1.00

25.4

0.28

7.24

inches (mm)

Ratings

• Tension nominale 12 Volts

• Courant solaire nominal 25 A

La page charge ...

Morningstar SunSaver Duo Manuel utilisateur

Morningstar SunSaver Duo Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents