Transition Networks CBFTF1010-130 Manuel utilisateur

Marque: Transition Networks

Modèle: CBFTF1010-130

Catégorie: Commutateurs réseau

Taper: Manuel utilisateur

Product features . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . .7

Cable Specifications . . . . . . . . . . . . .8

Troubleshooting . . . . . . . . . . . . . . . .9

Technical Specifications . . . . . . . . .10

Compliance Information . . . . . . . . .12

*Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of th network.

Part Number Port One - Copper

10/100Base-T(x)

Port Two Copper

10/100Base-T(x)

Port Three - Copper

10/100Base-T(x)

CBFTF1010-130 RJ-45 100 M

(328 ft*)

RJ-45 100 M

(328 ft*)

RJ-45 100 M

(328 ft*)

User’s Guide

CBFTF1010-130 10/100 Fault-Tolerant Redundant

Link Protector

• 10/100 Base-T(x) to 10/100 Base-T(x)

Ethernet/Fast Ethernet

• Three RJ-45 Ports

The CBFTF1010-130 is a fault-tolerant redundant link protector that provides redundant

paths for fast Ethernet devices. It has three RJ-45 ports. As a redundant link protector,

typically, the main port connects to a critical 10/100 fast Ethernet device. The primary

port and the backup port connect to two different switch ports or two different ports on

separate switches. When the unit powers up, it checks the primary port for a link signal; if

the signal is present, the main and primary ports connect and the signal from the backup

port is then disabled. Any device connected to the backup port will not detect a signal at

this time. However, if the device does not detect a signal on the primary port, then the

main port and backup port connect.

Optional functionality controlled via DIP switches enable changing the transceiver from

fault-tolerant mode to switch mode.

Product Features

Front panel

The CBFTF1010-130 bridging media converter has three RJ-45 10/100Base-TX

ports. See illustration below.

Auto-Negotiation (selectable)

The Auto-Negotiation feature automatically configures the bridging media

converter to achieve the best possible mode of operation over a link. The bridging

media converter broadcasts its speed (10 Mbps or 100 Mbps) and duplex

capabilities (full or half) to the other devices and negotiates the best mode of

operation. Auto-Negotiation allows quick and easy installation because the optimal

link is established automatically—no user intervention required.

In a scenario where the media converter is linked to a non-negotiating device,

disable Auto-Negotiation. In this instance, the mode of operation will drop to the

least common denominator between the two devices (e.g., 10 Mbps, half-duplex).

Disabling this feature allows forcing the connection to the desired speed and duplex

mode.

Data transfer rate (selectable)

10Base-T data transfer rate: 10 Mbps Ethernet.

100Base-TX data transfer rate: 100 Mbps Ethernet.

Full-Duplex network (selectable)

In a full-duplex network, maximum cable lengths are determined by the type of

cables used. The 512-Bit Rule does not apply in a full-duplex network.

Half-Duplex network (selectable) (512-Bit Rule)

In a half-duplex network, the maximum cable lengths are determined by the round

trip delay limitations of each fast Ethernet collision domain. (A collision domain is

the longest path between any two terminal devices, e.g., terminal, switch, or router.)

The 512-Bit Rule determines the maximum length of cable permitted by calculating

the round-trip delay in bit times (BT) of a particular collision domain. If the result is

less than or equal to 512 BT, the path is good.

AutoCross™

When the AutoCross feature is activated, it allows either straight-through MDI or

crossover MDI-X cables to be used when connecting to 10Base-T or 100Base-TX

devices. AutoCross determines the characteristics of the connection and

automatically configures the unit to link up, regardless if the cable configuration is

MDI or MDI-X. This feature is permanently enabled.

Port 1 Port 3

BLK PRI PWR

CBFTF

Port 2

CBFTF1010-130

Technical Support: 1.800.466.4526. Press "2" -- International: 1.408.744.2751

Installation

Note: Wear a grounding strap when removing the circuit board from its anti-static

bag.

Jumpers

The two, 3-pin headers located on the inner surface of the board are used to select

“hardware” and “software” modes, and “redundancy.” See photo below.

• Hardware Mode: DIP switches control the function of the board. You can view

status only via the Web or Focal Point interface.

• Software Mode: Software controls the function of the board. The DIP switches do

not function in software mode.

• Redundancy: automatically switches data transfer responsibilities to the secondary

port if the primary port fails.

CBFTF1010-130

[email protected] -- Click the “Transition Now” link for live Web chat.

Product features -- continued

Redundancy (selectable)

With redundancy enable and the primary port fails, the converter automatically

switches data transfer responsibilities to the backup port without disrupting network

traffic. After the primary port's failure is resolved, the converter automatically

switches data transfer responsibilities back to the primary port.

Parallel detection

Parallel detection is the method used to link when an auto negotiating port detects a

link partner that is in forced mode and therefore cannot participate in the auto

negotiating process. Parallel Detection can be set to IEEE Standard half duplex, or

the non-standard full duplex. Switch settings for parallel detection are valid in

hardware or software mode, only when Auto-Negotiation is enabled.

Per the IEEE method, an auto negotiating port that detects a forced link partner

should drop to the detected speed (10Mbs or 100Mbs) and default to half duplex

The BFTF-130 allows bypassing the IEEE method by setting the parallel detection

default mode to half or full duplex via DIP switch 3.

(Shunt in Default Position)

Letter "H" = Hardware

J4 (3-Pin Header)

J2 (3-Pin Header)

Letter "S" = Software

Letter "R" = Redundant

Shunt in Redundant Position

(Default)

Installation -- continued

DIP switch settings

Four (4) DIP switches, see illustration below.

• SW 1: Auto-Negotiation

• SW 2: Speed

• SW 3: Duplex

• SW 4: Redundancy

CBFTF1010-130

Tech Support: 1-800-260-1312 International: 00-1-952-941-7600, 24 hours

1342

Down

1342

Down

1342

When Auto-Negotiation is enabled (switch #1 UP), the bridging media

converter advertises all rate and mode capabilities to the network:

100Mb/s full duplex, 100Mb/s half-duplex, 10Mb/s full duplex, and

10Mb/s half duplex.

Note: Switch “2” does not function when switch “#1” is in the UP position (Auto-

Negotiation enabled).

When auto-negotiation is disabled (switch #1 DOWN), the bridging

media converter does not advertise rate and mode capabilities to the

network.

100Base-TX data transfer rate (switch #2 UP), 100 Mbps fast Ethernet.

10Base-TX data transfer rate (switch #2 DOWN), 10 Mbps fast Ethernet.

Note: See the diagrams below and use a very small flat-blade screwdriver or similar

tool to set the DIP switch.

1234

Side View

4 DIP Switches

CBFTF1010-130

[email protected] -- Click the “Transition Now” link for live Web chat.

Fully Inserted and Secured Card

Chassis Slot Screw Hole

Inserting Redundant Link

Protector Card

Installing the transceiver in the Point System chassis

To insert the redundant link protector card, do the following:

1. Wearing a ground strap, slide the card into an available slot in the Point System

chassis. See photo below.

2. Push the card all the way into the slot (should snap in).

3. Push in and turn the screw clockwise to secure the card to the chassis frame.

1342

Down

1342

Down

1342

Forced Full duplex (switch #3 UP with auto-negotiation disabled ). Also

when Parallel detection occurs (auto-negotiation enabled only), the

device will be forced to IEEE Standard half duplex

Forced Half duplex (switch #3 DOWN with auto-negotiation disabled ).

Also when Parallel detection occurs (auto-negotiation enabled only),

the device will be forced to non-standard full duplex.

Redundancy enabled switch #4 UP (with J2 shunt in the “R” position)

See notes below.

Note: With redundancy turned OFF, the primary and secondary port LEDs will turn

OFF, returning these ports to normal functionality.

Note: The functionality for each switch setting applies to all ports simultaneously.

Note: With the shunt removed from header J2, the switch is set to redundant mode.

Installation -- continued

Setting DIP switches -- continued

Redundancy disabled switch #4 DOWN (3-port switch mode)

CBFTF1010-130

Tech Support: 1-800-260-1312 International: 00-1-952-941-7600, 24 hours

Installation -- continued

RJ-45 cable pin assignments

Installing the RJ-45 cable

1 Locate or build an IEEE 802.3 compliant 10Base-T or 100Base-TX cables, with

male RJ-45 connectors installed onto both ends.

2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the

bridging media converter as shown below.

3. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port on the

other device (switch, workstation, etc.) as shown below.

Note: The MDI (straight-through) cable or the MDI-X (crossover) cable connection

is configured automatically, according to network conditions.

RJ-45 Port

Transceiver

RJ-45 Port

Switch,Workstation, etc.

12345678

Pair 1

Pair 2

RJ-45 10Base-T

CBFTF1010-130

[email protected] -- Click the “Transition Now” link for live Web chat.

Pr imary

Po wer

Link/Act/SPD

(Qty 3)

Duple

(Qty 3)

Fr ont View

Port 2

Port 3Port 1

(Secondary)

Backup

Card LEDs

Power (PWR): LED ON indicates chassis is powering the board

Primary: ON when the primary port is in use

Backup (Secondary): ON when the secondary port is in use

TP port LEDs

LINK/ACT/SPD: Green (ON) for 100 Mbps and Link/Act; Flashing when

transmitting data; Orange for 10Mbps

Duplex (DPX): Green (ON) for full duplex; OFF for half duplex

Management features

• Mirror port mode

• Twisted pair port control:

-Auto-Negotiation

-Pause

-Speed

-Duplex

AutoCross

• VLAN tagging

-Port default tag insertion

-Tag insertion and removal

• MIB counters per port

Operation

Status LEDs

There are three (3) LEDs on the converter chassis front panel and two (2) on each

TP port.

CBFTF1010-130

Tech Support: 1-800-260-1312 International: 00-1-952-941-7600, 24 hours

Cable Specifications

Copper cable (10Base-T/100Base-TX)

Ensure that the correct cable type is installed to support the highest speed and mode of

operation. Though category 3 cable is adequate for a 10Base-T installation, category 5

cable is recommended, since category 3 cables DO NOT support 100Base-TX.

Category 3: (minimum requirement for 10 Mbps operation)

Gauge: 24 to 22 AWG

Attenuation: 11.5 dB/100m @ 5-10 MHz

Maximum cable distance: 100 meters

Category 5: (minimum requirement for 100 Mbps operation)

Gauge: 24 to 22 AWG

Attenuation: 22.0 dB/100m @ 100 MHz

Maximum cable distance: 100 meters

• Straight-through (MDI) or crossover (MDI-X) cable may be used.

• Shielded (STP) or unshielded (UTP) twisted-pair cable may be used.

• Pins 1&2 and 3&6 are the two active pairs in an Ethernet network.

• Use only dedicated wire pairs for the active pins:

(e.g., blue/white & white/blue, orange/white & white/orange, etc.)

• Do not use flat or silver satin wire.

10Base-T and the Ethernet collision domain:

• Refer to the 5-Segment Rule before installing half-duplex 10Base-T

cable.

• Installing full-duplex twisted-pair cable avoids collision domain

considerations—maximum distance 100 meters.

100Base-TX and the Fast Ethernet collision domain:

• Refer to the 512-Bit Rule before installing half-duplex 100Base-TX cable.

• Installing full-duplex twisted-pair cable avoids collision domain

considerations—maximum distance 100 meters.

Note: A Fast Ethernet collision domain can have only “1” Class “I” repeater or “2”

Class “II” repeaters.

Crossover Cable

Straight-Through Cable

Twisted Pair #1

Twisted Pair #2

CBFTF1010-130

[email protected] -- Click the “Transition Now” link for live Web chat.

Troubleshooting

If the CBFTF1010-130 fails or initially does not power up and function properly,

answer the following questions and take the suggested corrective actions.

1. Is the power LED on the bridging media converter ON?

NO:

a. Is the chassis plugged into AC power?

b. Is the card fully inserted into the chassis?

c. Contact Technical Support: 1.800.466.4526.

YES: Go to step 2.

2. Is there an active (connected to an output source) RJ-45 cable inserted into the

bridging media converter’s main port?

NO:

a. Insert an RJ-45 cable into the bridging media converter main port.

b. Insert the other cable end into an active device.

YES: Go to step 3.

3. Is the link/active LED on the main port lit (ON)?

NO:

a. Check that the RJ-45 cable is properly inserted into the bridging media

converter main port.

b. Check that the other cable end is inserted into an active device.

c. Check the cable for damage.

d. Contact Technical Support.

YES: Go to step 4.

4. Is there an RJ-45 cable inserted into the primary port on the bridging media

converter?

NO:

a. Insert the RJ-45 cable into the bridging media converter primary port.

b. Insert the other end of the cable into the input of an active device.

YES: Go to step 5.

5. Is the primary LED on the chassis lit (ON)?

NO:

a. Check that the RJ-45 cable is properly inserted into the primary port.

b. Check that the other end of the cable is properly inserted into an active

device.

c. Check the cable for damage.

d. Contact Technical Support.

YES: Go to step 6.

CBFTF1010-130

Technical Support: 1.800.466.4526. Press "2" -- International: 1.408.744.2751

Troubleshooting -- continued

6. Is there an RJ-45 cable inserted into the secondary port on the bridging media

converter?

NO:

a. Insert the RJ-45 cable into the bridging media converter secondary port.

b. Insert the other end of the cable into the input of the an active device.

YES: Go to step 7.

7. Is the secondary LED on the board lit (ON)?

NO:

a. Check that the RJ-45 cable is properly inserted into the secondary port.

b. Check that the other end of the cable is properly inserted into an active

device.

c. Check the cable for damage.

c. Contact technical support.

8. YES: Contact technical support: 1.800.466.4526.

Technical specifications

Standards: IEEE 802.3™ 2000

Regulatory: Emissions: EN55022 Class A, Immunity: EN55024

Safety compliance: CE Mark

Data Rate: 10 Mbps, 100 Mbps

Dimensions: 0.86”W x 5.0”D x 3.4”H

(22 mm x 127 mm x 86 mm)

Shipping weight: 1 lb. approximately

Power consumption: 2.4 watts

Power supply: Powered by chassis

Operating temp: 0°C to 50°C (32°F to 140°F )

Switching time: <189 ms (primary to secondary)

Storage temp: -20°C to +85°C (-4°F to 185°F)

Humidity: 5% to 95%, non-condensing

Altitude: 0 – 10,000 feet

Warranty: Lifetime

CBFTF1010-130

[email protected] -- Click the “Transition Now” link for live Web chat.

Technical support

Technical support is available at [email protected]

• US and Canada: 1-800-260-1312 (24 hours)

• International: 00-1-952-941-7600 (24 hours)

Transition now

Chat live via the Web with Transition Networks Technical Support. Log onto

www.transition.com and click the Transition Now link.

Web-based seminar

Transition networks provides seminars via live, web-based training. Log onto

www.transition.com and click the Learning Center link.

Ask a question anytime by sending an email to our technical support staff:

[email protected]

Address

Transition Networks

6475 City West Parkway

Minneapolis, MN 55344, U.S.A.

Telephone: 952-941-7600,

Toll free: 800-526-9267

Fax: 952-941-2322

Declaration of Conformity

Name of Mfg: Transition Networks, 6475 City West Parkway,

Minneapolis, MN 55344 U.S.A.

Model: CBFTF1010-130 Bridging Media Converter

Part Number: CBFTF1010-130

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the CBFTF1010-130 to which this declaration

refers is in conformity with the following standards:

CISPR 22:1997+A1:2000; EN 55022:1998+A1:2000 Class A; FCC Part 15 Subpart B;

21CFR subpart J

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s)

and Standard(s).

January, 2007

Stephen Anderson, Vice-President of Engineering Date

CBFTF1010-130

Trademark notice

All registered trademarks and trademarks are the property of their respective owners.

used in any form or by any means—graphic, electronic or mechanical—without written permission

from Transition Networks.

Printed in the U.S.A. 33350.B

Compliance Information

CSA Certified

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC regulations

This equipment has been tested and found to comply with the limits for a class A digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out

on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage

radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

WARNING: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Achtung ! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei

Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für

Gegenmaßnahmen verantwortlich.

Attention ! Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de

créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures

spécifiques appropriées.

In accordance with European Union Directive 2002/96/EC of the European Parliament

and of the Council of 27 January 2003, Transition Networks will accept post usage

returns of this product for proper disposal. The contact information for this activity can

be found in the 'Contact Us' portion of this document.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result

in damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst

gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der

Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der

gegenseitigen Anerkennung ihrer Konformität.

Transition Networks CBFTF1010-130 Manuel utilisateur

Marque: Transition Networks

Modèle: CBFTF1010-130

Catégorie: Commutateurs réseau

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Transition Networks CBFTF1010-130 User manual

Transition Networks CBFTF1010-130 Manuel utilisateur

Transition Networks CBFTF1010-130 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents