CTC Union SDTU-01 Manuel utilisateur

Marque: CTC Union

Modèle: SDTU-01

Catégorie: Les routeurs

Taper: Manuel utilisateur

Ce manuel convient également à

xDSL Series

User's Manual

Contents

Overview.............................................................................................. 3

Features.............................................................................................. 4

Applications......................................................................................... 4

Specifications...................................................................................... 5

Packing................................................................................................ 6

Appearance......................................................................................... 7

Front Panel....................................................................................... 7

Rear Panel........................................................................................ 8

Important Safety Instructions............................................................. 9

Installation...........................................................................................11

Hardware Setup.................................................................................13

Point-to-point Operation.....................................................................14

Console Operation.............................................................................15

Console Operation / Configuration....................................................16

Cables.................................................................................................18

SDTU-01 SDSL V.35 DSU

Overview

The SDTU-01 SDSL DSU with V.35 interface is a data access DSU

modem with the latest multi-rate SDSL (Symmetrical Digital Subscriber

Line) technology offering both long range and high speed data

transmission with rates from 144Kbps up to 2320Kbps. The

transmitting data rate may be adapted for the best "rate vs. range"

performance for efficient and stable data transmission.

The SDTU-01 uses the 2B1Q line code with echo cancellation to

transmit its high data rate over a single twisted pair of telephone wire

without being affected by bridge taps or mixed cable links. It also

provides high immunity to background noise and enables transmission

over multiple pair cables.

SDTU-01 SDSL V.35 DSU

Features

4 High speed SDSL transport over single twisted Copper pair

telephone line

4 2B1Q line code

4 Symmetrical Multi-rate data transmission from 144Kbps to

2320Kbps

4 Simple operation

4 Low power consumption

4 Transparent data over SDSL

4 Point-to-point data transmission service

4 Supervision via RS-232 Craft port

Applications

LAN

Router

SDTU-01

LAN

Router

SDTU-01

Application : Point-to-Point Connection for Network Extension

SDTU-01 SDSL V.35 DSU

Specifications

Item SDTU-01

Data Port Interface V.35

Connector DB-25

WAN Port --

SDSL Line I/F

Transmission Rate : 144 Kbps – 2320 Kbps

Data Rate : 144 Kbps – 2320 Kbps

Line Code 2B1Q

Line Impedance

135 Ω

Test Standard ANSI T1E1.413/94-006; ETSI ETR 152

Connection Loops One Pair (2-wire)

Connector RJ-11

Indicators

LED

Power

Activity

Link Status

WAN Status

Alarm

Green LED, indicate power and operation

Green LED, DSL data activity status

Green LED, Local Data port Link status

Green LED, DSL Link Status

Green LED, Self-test & Error status

OAM&P Local ASCII Terminal via EIA RS-232 Port

Environment Temperature

Humidity

0°C ~ 50°C

5% ~ 95%

Dimensions

(WxDxH)

CPE 220mm X 169mm X 40mm

Electrical Power Input

Power Consumption

12VDC via AC Adapter

Less than 5 Watts

SDTU-01 SDSL V.35 DSU

Packing

This package shall contain the following items:

1. SDTU-01 unit

2. AC Adapter (120VAC

for North America, and

220-240VAC for

Europe)

3. RJ-11 Cable

4. RS-232 Serial Cable,

DB-9 to DB-9(optional)

5. DB25-V35 Cable

6. This manual

SDTU-01 SDSL V.35 DSU

Appearance

Front Panel

Connect all cables and power on the SDTU-01, LED’s on front panel

shall indicate the following status.

ALM: On when there is an error, if it remains On all the

time, please call customer service.

WAN: On when there is an active and connected

WAN

(SDSL Sync.)

PWR: On when the power supply is properly connected.

ACT: On and blink when there are data activities.

LINK: On when V.35 port is properly connected to Router.

SDTU-01 SDSL V.35 DSU

Rear Panel

RJ11, SDSL for

connection to

local loop

DB9, console port for

connection to ASCII

data terminal

DB25, V.35 serial Data Port, for

connection to a router

4P DIP switch, for setting speed &

CO/RT

Power Jack, for connecting to a AC-DC

power adapter, 12VDC, 1A

V.35

DC-IN

TERMINAL

WANRATE

DIP ON

SDTU-01 SDSL V.35 DSU

Important Safety Instructions

The following safety instructions apply to the SDTU-01:

1. Be sure to read and follow all warning notices and instructions.

2. The maximum recommended ambient temperature for SDTU-01 is

40(104) Care must be taken to allow sufficient air circulation or

space between units when the SDTU-01 is installed inside a closed

rack assembly. The operating ambient temperature of the rack

environment might be greater than room temperature.

3. Installation in a rack without sufficient air flow can be unsafe.

4. Racks should safely support the combined weight of all equipment.

5. The connections and equipment that supply power to the SDTU-01

should be capable of operating safely with the maximum power

requirements of the SDTU-01. In the event of a power overload, the

supply circuits and supply wiring should not become hazardous. The

input rating of the SDTU-01 is printed on the nameplate.

6. The AC adapter must plug in to the right supply voltage, i.e. 120VAC

adapter for North America and 230VAC adapter for Europe. Be sure

the supplied AC voltage is correct and stable. If the input AC voltage is

over 10% lower than the standard may cause to malfunction of the

SDTU-01 unit.

7. Installation in restricted access areas must comply with Articles 110-16,

110-17, and 110-18 of the national Electrical Code, ANSI/NFPA 70.

8. Do not allow anything to rest on the power cord of the AC adapter, and

do not locate the product where anyone will walk on the power cord.

9. Do not service the product by yourself. Opening or removing covers

can expose you to dangerous high voltage points or other risks. Refer

all servicing to qualified service personnel.

10. General when installed in the final configuration, the product must

comply with the applicable safety standards and regulatory

requirements of the country in which it is installed. If necessary,

consult the appropriate regulatory agencies and inspection authorities

to ensure compliance.

SDTU-01 SDSL V.35 DSU

11. A rare condition can create a voltage potential between the earth

grounds of two or more buildings. If products installed in separate

building are interconnected, the voltage potential can cause a

hazardous condition. Consult a qualified electrical consultant to

determine whether or not this phenomenon exists and, if necessary,

implement corrective action before interconnecting the products. If the

equipment is to be used with telecommunications circuit, take the

following precautions:

4 Never install telephone wiring during a lightning storm.

4 Never install telephone jacks in wet location unless the jack is specially

designed for wet location.

4 Never touch uninsulated telephone wires or terminals unless the

telephone line has been disconnected at the network interface.

4 Use caution when installing or modifying telephone lines (other than a

cordless telephone) during an electrical storm. There is a remote risk of

electric shock from lightning.

4 Do not use a telephone or other equipment connected to telephone

lines to report a gas leak in the vicinity of the leak.

SDTU-01 SDSL V.35 DSU

TERMINAL

RATE

Router

TERMINAL

RATE

TERMINAL

RATE

Installation

Connect the local loop

(twisted copper pair

telephone wire) to the WAN

port (SDSL, RJ-11) by

using the RJ-11 cable

attached. Be sure this local

loop had been properly

connected to the Central

Office side SDSL

equipment.

Connect the DB-25

connector marked "V.35"

with "DB-25 to V.35" cable

to the router. To correctly

connect with the router

cable. Please refer to the

section of "Cables" for

detail pin assignment. The

other end of router will

connect to LAN (Local Area

Network) or other data

equipment.

Power connection --

• Warning : Do not apply

the AC power before all

the connections above

have been connected.

• Plug in the AC Adapter to

the wall AC socket

• Connect the DC jack to the

DC-IN of the unit

SDTU-01 SDSL V.35 DSU

TERMINAL

RATE

RS232

Terminal Connection --

• A data terminal can be

connected to the

TERMINAL port (RS-232)

of the unit for configuration

& monitoring purpose. Use

the RS-232 serial cable to

connect to a ASCII data

terminal. The TERMINAL is

VT-100 compatible.

• A PC with data terminal

emulation software

installed, can be connected

via serial COM port in data

terminal mode.

SDTU-01 SDSL V.35 DSU

Hardware Setup

DSL rate and terminal type can be set up by adjusting the 4-pole DIP switch

on the rear panel. Sw. 1 to Sw. 3 are for adjusting the DSL rate while Sw. 4

is for termination type.

1. DSL Rate Setting

Rate No.1 No.2 No.3

144K ON ON ON

272K ON ON OFF

400K ON OFF ON

528K ON OFF OFF

784K OFF ON ON

1168K OFF ON OFF

1552K OFF OFF ON

2320K OFF OFF OFF

2. CO/RT configuration

Terminal type DIP SW No. 4

CO ON

RT OFF

SDTU-01 SDSL V.35 DSU

Point-to-point Operation

1. The SDTU-01 should be located on each side of the connection. One

side must be set to "CO" and the other side must be set to "RT". Refer

to the section on "Hardware Setup" for the CO & RT setup.

2. Insure that both CO & RT SDTU-01s are set to the same DSL rate. For

example, 784Kbps.

3. Make sure that both CO & RT SDTU-01s have been connected to the

Routers properly.

4. Check the WAN LED on the SDTU-01 -- it will remain lit when the Link

is successfully established. The DSL training process may take around

one minute and the WAN LED will flash during the training process.

5. After the DSL link is established, check the router setup. Both CO & RT

side routers must be set to use the same Link Protocol, i.e. PPP or

Frame Relay link. Both side routers must also set the same

parameters. Otherwise, they may fail to communicate with each other

even though the DSL link is ready.

6. Follow the Router manual to set the IP and other parameters. When

the router is properly set, you are ready to use the high-speed

connection between the two networks. You may test the data

transportation speed by using the "Ping" command or FTP file transfer.

SDTU-01 SDSL V.35 DSU

Console Operation

Starting Hyper-Terminal (on Windows 95 or Windows NT)

To Start the Hyper-terminal, following the steps below:

1. Start "Hyper-terminal" program --

− On Windows 95 or Windows NT : start Tool Bar à Program à

Accessory à Hyper Terminal Group à Double Click

Hypertrm.exe à Enter Connection Name à Select Icon à Click

2. Select COM port to communicate with the SDTU-01--

− Choose direct to COM1 or COM2 à click OK

3. Set up Port Properties --

n Port Setting :

− Bit per second : 57600

− Data bits : 8

− Stop bits : 1

− Parity bit: None

− Flow Control : None

n Settings :

− Function, arrow, and ctrl keys act as : Windows keys

− Emulation : Auto-detect

− Back-scroll buffer lines : 500

n ASCII Setup:

− Echo typed characters locally

− Line delay : 0 milliseconds

− Character line feeds t incoming line ends : enable

SDTU-01 SDSL V.35 DSU

Console Operation / Configuration

1. Turn on the power of SDTU-01, the terminal screen will display :

The booting screen will stay for about 6 seconds before entering the

Main Menu.

2. Main Menu display--

3. Select "0" display --

Descriptions of select items --

3.1. Bit Pump Status : Bit Pump Chip detection; OK or NG(No

Good).

3.2. Terminal Type : Indicate whether the Terminal Type of this

unit is set for CO(Central Office) or RT(Remote Terminal).

3.3. Operation Status : Indicates the DSL operation mode as

UP(Normal Operation) or DN(Down, During Start up).

SDSL V.35 DSU Software Version xxx

0. Show DSL Status

1. Upgrade Operation Software

2. Upgrade SDSL Firmware

Select Function Item ?__

Firmware Version xxx Software Version xxx

Bitpump Status: OK Terminal Type: RT

Operation Status: DN V.35 OFF_Line

Noise Margin: -15.5 dB Data Rate: 2320 kbps

Press any key to return main manual….

Booting Code_Version: xxx

DRAM BANK0 Check O.K.

DRAM BANK1 Check O.K.

Wait, booting now……….

SDTU-01 SDSL V.35 DSU

3.4. V35 : To indicate whether V.35 is Active(ON_Line) or Not

Active(Off_Line).

3.5. Noise Margin : Shows Noise Margin value.

3.6. Data Rate : Shows current transmission data rate (e.g.

1552Kbps)

4. Select "1" display -- Upgrade Operation Software

4.1. The XMODEM window will be opened, type in the file directory

e.g. A:

(Note: the Communication Protocol should be "Xmodem")

4.2. A window will be activated to show the status to download the

Operation Software Code.

4.3. When finishing the downloading process, the SDTU-01 will be

reset and the console screen will be back to initial booting

screen.

5. Select "2" display -- Upgrade SDSL Firmware

Are you sure you want to upgrade "Operation Software" ?

(Y/N)

Enter Password : 2000

Start to Receive Program from Console by X_MODEM !

Are you sure you want to upgrade "SDSL Firmware" ? (Y/N)

Enter Password : 2000

Start to Receive Program from Console by X_MODEM !

SDTU-01 SDSL V.35 DSU

5.1. The XMODEM window will be open, type in the file directory

e.g. A:

(Note: the Communication Protocol should be "Xmodem")

5.2. A window will be activated to show the status to download the

SDSL Firmware Code.

5.3. When finishing the downloading process, the SDTU-01 will be

reset and the console screen will return to the initial booting

screen.

Cables

1. RS-232 Cable for connection to VT-100 type ASCII terminal

4 CRAFT Port DB-9 connector pin assignment :

− Pin 2 ------ TXD

− Pin 3 ------ RXD

− Pin 5 ------ GND

4 Parameter :

− Data Speed : 57600 bps

− Parity : None

− Stop Bit : 1 bit

− Character Length : 8 Bits

male

female

La page charge ...

CTC Union SDTU-01 Manuel utilisateur

Marque: CTC Union

Modèle: SDTU-01

Catégorie: Les routeurs

Taper: Manuel utilisateur

Ce manuel convient également à

xDSL Series

Télécharger le PDF

rapport

dans d''autres langues

English: CTC Union SDTU-01 User manual

CTC Union SDTU-01 Manuel utilisateur

Ce manuel convient également à

CTC Union SDTU-01 Manuel utilisateur

dans d''autres langues

Autres documents