SUN GLOW Roller Shade Dual Square Fascia Manuel utilisateur

Marque: SUN GLOW

Modèle: Roller Shade Dual Square Fascia

Taper: Manuel utilisateur

www.mysunglow.com

Installation Instructions | Dual Square Fascia | 2022-09-17 1 of 5

Roller Shade

Dual Square Fascia Installation Instructions

WARNING MISE EN GARDE

STRANGULATION HAZARD — Young children

can be strangled by cords. Immediately remove this

product if a cord longer than 22 cm or a loop

exceeding 44 cm around becomes accessible.

RISQUE D’ÉTRANGLEMENT — Les enfants en bas

âge peuvent s’étrangler avec des cordes. Enlevez

immédiatement ce produit si une corde mesurant

plus de 22 cm devient accessible ou si le contour

d’une boucle de plus de 44 cm devient accessible.

NOTE: Fabric wrapped valances must be handled with care

1PREPAR ATION

GComponent List

A. Front Shade

B. Back Shade

C. Fascia

D. Mounting Bracket

E. Chain Diverter

F. Chain Diverter Placeholder

G. Bracket Cover (Optional)

2MOUNT THE BRACKETS

For inside mounts using ceiling and wall mount, brackets must be installed to ensure a 1/8” gap is left on each side for end caps.

CEILING MOUNT WALL MOUNT LATERAL MOUNT

*note: for ceiling mount ensure that the center

and back mounting holes are used if the fascia

cover is inverted. If the cover is not inverted,

the front mounting hole may be used.

Roller Shade - Dual Square Fascia

Installation Instructions

www.mysunglow.com

Installation Instructions | Dual Square Fascia | 2022-09-17 2 of 5

INSTALL UPPER THE SHADE

NOTE: For shades with Zero Gravity, please refer to Zero Gravity instructions on page 4 at this stage.

STEP 3A: INSTALL PIN END FIRST STEP 3B: INSTALL CLUTCH END

Put the spring loaded Pin End into the hole in the bracket. Keeping gentle pressure against the Pin End lift the clutch end

up and align the two hooks on the clutch with the two slots in the

bracket. The hooks should fall into place in the bracket, pull down

gently to secure the blind into the bracket.

4LOOP CHAIN AROUND BEARINGS (CHAIN ONLY)

If the upper shade being installed is a chain driven shade,

ensure the chain falls behind the guide bearings.

5INSTALL LOWER THE SHADE

NOTE: For shades with Zero Gravity, please refer to Zero Gravity instructions on page 4 at this stage.

STEP 5A: INSTALL PIN END FIRST STEP 5C: INSTALL CLUTCH END

Put the spring loaded Pin End into the hole in the bracket. Keeping gentle pressure against the Pin End, lift the clutch end

up and align the two hooks on the clutch with the two slots in the

bracket. The hooks should fall into place in the bracket, pull down

gently to secure the blind into the bracket.

www.mysunglow.com

Installation Instructions | Dual Square Fascia | 2022-09-17 3 of 5

6INSTALL THE CHAIN DIVERTER/PLACEHOLDER

Insert the front chain into the outside channel on the chain diverter, then insert the rear chain into the rear inside channel.

Then insert the chain diverter into the mounting bracket until you here an audible click. Also insert the placeholder tab into the

mounting bracket on the idle end. If not using a chain system, the diverter is replaced with a secondary placeholder.

1. Back shade slot A

2. Back shade slot B

3. Front shade slot A

4. Front shade slot B

insert

7INSTALL THE FASCIA

NOTE: For inside mount shades: snap the bracket covers on before hooking to the mounting brackets

(1) Hook the fascia on the top corner of the mounting brackets,

(2) then swing the bottom in. (3) You should hear a distinct click.

*click*

8INSTALL THE BRACKET COVERS

See step 2: For inside mounts, brackets must be

installed to ensure a 1/8” gap is left on each side for end

caps.

1. Remove backing from adhesive strips.

2. Apply end caps to end brackets 12

9INSTALL THE SAFETY SHIELD (CHAIN ONLY)

NOTE: For shades with chain operation only.

Ensure that Safety Shield is carefully and properly installed.

www.mysunglow.com

Installation Instructions | Dual Square Fascia | 2022-09-17 4 of 5

Zero Gravity - Fascia or Open Roll Instructions

These steps are not required for Zero Gravity in Curved Cassettes.

Skip these steps if using chain, Neo, or motorized control

If the Pin End of the shade

appears as shown here,

proceed with Steps 1,2

& 3 before returning to

Step 4 of the Open Roll

Installation Instructions

If the Pin End of the shade

appears as shown here,

proceed with Steps 4,5

& 6 before returning to

Step 4 of the Open Roll

Installation Instructions

1PREPARING FOR INSTALLATION

NOTE: The blue shipping lock is used to

lock the tension in place during shipping.

Remove shipping lock before installing

Hex Plunger

2INSTALLING THE SYSTEM

(A) Insert the pin end of the blind into the bracket.

(B) Insert the hooked end into the other side bracket, and ensure the Zero Gravity head sits on the hooked

teeth firmly. This should compress the hex plunger which releases the tension onto the shade.

Push

BPush

3TESTING THE SYSTEM

Always operate the shade from the center of the bottom bar. Ensure that the shade is balanced and

does not want to roll up or down on its own. If it does, then the spring will require more or less tension to

be perfectly balanced. If the shade requires more tension, turn the zero gravity head into the fabric, ie

opposite direction to the fall of the fabric.

Insert for 5mm hex

(only for outside mount)

Adjusting Spanner

www.mysunglow.com

Installation Instructions | Dual Square Fascia | 2022-09-17 5 of 5

Zero Gravity - Fascia or Open Roll Instructions

These steps are not required for Zero Gravity in Curved Cassettes.

Skip these steps if using chain, Neo, or motorized control

WARNING

• Do not pull pin lock out until shade is installed or tension will be released.

• If tension has been released, see trouble shooting.

1RUBBER BAND REMOVAL

Before installing the shade remove the rubber band holding the Pin Lock in place.

2INSTALL SHADE AND REMOVE PIN LOCK

C: Install roller shade while keeping Pin

Lock toward you and held in place.

D: After installation remove the pin lock

C D

3TESTING THE INSTALLED ROLLER SHADE

Installed roller shade must be operated

smoothly by the centre of the bottom

bar to avoid excessive telescoping

TROUBLE SHOOTING:

ONLY REQUIRED IF TENSION IS RELEASED

If the tension is released or removed accidentally follow these instructions:

The tension can be put back in any Zero Gravity Mini by turning the clutch head in the

opposite direction of the fabric approximately 1 – 2 full rotations. While holding tension,

insert the Pin Lock into the hole of the clutch. PROCEED WITH STEP 2 WHEN FINISHED.

SUN GLOW Roller Shade Dual Square Fascia Manuel utilisateur

Marque: SUN GLOW

Modèle: Roller Shade Dual Square Fascia

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: SUN GLOW Roller Shade Dual Square Fascia User manual

Documents connexes

SUN GLOW Roller Shade Savalan Window Decor Manuel utilisateur

SUN GLOW Roller Shade Dual Square Fascia Manuel utilisateur

SUN GLOW Roller Shade Dual Square Fascia Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents