ALTA R Series Roller Shades Manuel utilisateur

ROLLER SHADES

R-Series

Thank you for your purchase. This shade has been custom built for you from the highest quality materials.

To avoid errors and save valuable time, please read these instructions before installing your new shade.

1. Pencil or Marker

2. Measuring Tape

3. Phillips Screwdriver

4. Level

5. Power Drill

7. Mounting Fasteners

1

Table of Contents Continued ........................................................................................................................................................................... Page 2

Getting Started ................................................................................................................................................................................................ Page 2

INSIDE MOUNT

Shades with No Top Treatment ........................................................................................................................................................................ Page 3

Shades with Square Cassette ......................................................................................................................................................................... Page 3

Shades with Curved Cassette ......................................................................................................................................................................... Page 4

Shades with 3” Fascia ..................................................................................................................................................................................... Page 5

Shades with 4” Fascia .................................................................................................................................................................................. Page 6-7

Shades with Pocket ...................................................................................................................................................................................... Page 8-9

Shaded with Fabric Cornice .......................................................................................................................................................................... Page 10

Shaded with Deluxe Valance .......................................................................................................................................................................... Page 10

OUTSIDE MOUNT

Shades with No Top Treatment .......................................................................................................................................................................Page 11

Shades with Square Cassette ........................................................................................................................................................................Page 11

Shades with Curved Cassette ....................................................................................................................................................................... Page 12

Shades with 3” Fascia ................................................................................................................................................................................... Page 13

Shades with 4” Fascia .............................................................................................................................................................................. Page 14-15

Shades with Pocket .................................................................................................................................................................................. Page 16-17

Shades with Fabric Cornice ....................................................................................................................................................................... Page 18-19

Installing Deluxe Valance ............................................................................................................................................................................... Page 19

TABLE OF CONTENTS

Mounting Surface Fastener

Drywall, Plaster Wall Anchors, Expansion Bolts

(Not provided)

Metal Sheet Metal Screws

(Not provided)

Wood No. 6 Hex Head Screws

(Provided)

INSTALLATION INSTRUCTIONS

TOOLS YOU WILL NEED

Required installation components are wrapped in your package along with these instructions.

NOTE: Some parts may vary depending on the selected mounting options or control system options and whether intermediate brackets are required.

Motorized Shades .......................................................................................................................................................................................... Page 19

Straightening the Shade ................................................................................................................................................................................ Page 20

Care and Cleaning ......................................................................................................................................................................................... Page 20

Child Safety ................................................................................................................................................................................................... Page 20

TABLE OF CONTENTS

2

With proper installation, operation, and care, your new shades will provide years of beauty and performance. Please thoroughly review this instruction

booklet before beginning the installation. If the installation brackets are mounted correctly, the rest of the installation process will follow easily.

Make sure mounting surface is level. Brackets must be in line and level. Shim brackets if necessary.

The head rail must be level for the shade to operate properly.

Once the brackets are secured and level, the fabric roll can be inserted. Make sure your hands are clean to avoid soiling the fabric.

Shades with

No Top Treatment — Standard

Cassette

Curved Cassette Square Cassette

Deluxe Valance Fabric Cornice

3” Fascia and 4” Fascia Pocket

#8 x 1/4”

Hex Head Screw

#8 x 3/8” Phillips Pan

Thread Forming Screw

#8 x 1/2”

Carriage Bolt

#8 Lock Nut

Inside Mount: Screws Only

Outside Mount: Screws & Brackets

Outside Mount

Bracket

Inside/Ceiling

Mount Bracket

Small Medium/Large

Slotted Angle Bracket

Bracket

GETTING STARTED

1. Measure correct spacing, mark the desired location

2. Install brackets – Brackets must be in line and level. Shim brackets if necessary.

Follow image below:

1. Hook cassette onto the bracket

2. Push the cassette towards the back

3. Allow the hook at the back of the cassette

to engage securely onto the hook at the

rear of the bracket.

To Remove the shade:

Reverse the steps above.

3

All Operating Systems

• Determine the control side. Bracket (B) with tab (foot) should be at the control side and the bracket (A) with V slot and T-Hook should be at

the idler side.

• The installation brackets are always mounted so that the inner surfaces face each other. Make sure all brackets are leveled and aligned.

• Insert control side into the foot of the bracket.

• Set the post of the idler end into the V slot of the idler side bracket. Rotate the T-hook on the idler side bracket over the post to lock in the

post and secure the fabric roll.

Flush Mounting Depth Requirement: 3-3/4”

Min. Mounting Surface Height Requirement: 1-1/2”

End Cap (attached at factory)

Flush Mount Depth Requirement: 1-1/4”

Min. Mounting Depth Requirement: 1-1/2”

1-1/2”

Control Side

Idler Side

V Slot

T-Hook Front

(B)

(A)

Shades with Square Cassette — INSIDE MOUNT

Shades with No Top Treatment — INSIDE MOUNT

1. Space brackets evenly. Using the installation bracket as a template, measure to the center of the brackets and mark the hole locations

with a pencil for drilling.

2. Install the brackets, make sure all brackets are leveled and aligned. Mount the shade.

Small Cassette

Figure A - Position the cassette valance so that the ridge engages into the top lip of all brackets.

Figure B - Rotate the bottom front of the cassette valance upwards until the rear of the cassette

valance engages into the bracket and snaps into place, as shown.

To remove the shade

• Hold the cassette at each bracket tab to disengage the rear of the cassette.

Medium/Large Cassette

Figure A - Position and securely engage rear of the cassette into the bottom hooks of the bracket.

Rotate cassette upward (1) and push backward (2).

Figure B - Hold the cassette release gently (3) to ensure the top of the cassette engaging into

the top lips of all brackets, as shown.

To remove the shade

• Hold the cassette, gently insert a athead screwdriver in between the top of the cassette

and each bracket tab to assist in releasing the cassette from the top bracket lips. Push the

cassette toward the back. Rotate downward to disengage the cassette.

Shades with Curved Cassette — INSIDE MOUNT

4

Flush Mounting Depth Requirement:

• 2-7/8” (small curved cassette)

• 3-3/4” (medium curved cassette)

• 4-3/8” (large curved cassette)

Min. Mounting Depth Requirement: 1-1/2”

Release Tab

Hooks

The open end of each bracket faces downward, as shown in the image. The bracket with a tab (foot) in the middle should be at the control side

and the bracket with V slot and T-Hook should be at the idler side.

• Install each bracket with two screws through the top.

Make sure all brackets are level and aligned.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the tab (foot) in the

middle of the bracket.

2. Set the post of the idler end into the V slot of the idler side bracket.

Rotate the T-hook over the post on the idler side bracket to lock in

the post and secure the fabric roll.

ATTACH THE FASCIA

• Please note, do not install fascia panel until shade is installed. Then assemble the two end brackets and the fascia panel.

• Place the top of the fascia panel into the top indention of the brackets. Rotate the panel down and snap it into place.

Shades with 3” Fascia — INSIDE MOUNT

5

Flush Mount Depth Requirement: 3-1/8”

Min. Mounting Depth Requirement: 2-7/8”

Fascia

Panel Rotator - Side

Bracket

The open end of each bracket faces downward, as shown in the image. The bracket with a tab (foot) in the middle should be at the control side

and the bracket with V slot and T-Hook should be at the idler side.

• Install each bracket with two screws through the top.

Make sure all brackets are level and aligned.

NOTE: If shade is ordered with Side and/or Bottom Channel, please refer to

Side/Bottom Channel Installation

Instructions.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the tab (foot) in the middle of the bracket.

2. Set the post of the idler end into the V slot of the idler side bracket. Rotate the T-hook over the post on the idler side bracket to lock

in the post and secure the fabric roll.

ATTACH THE FASCIA

3. Place the top of the fascia panel into the top indention of the brackets. Rotate the panel down and snap it into place.

See Side/Bottom Channel Installation Instructions on page 7.

6

Flush Mount Depth Requirement: 4-3/8”

Min. Mounting Depth Requirement: 3-7/8”

Shades with 4” Fascia — INSIDE MOUNT

Side/Bottom Channel Installation Instructions

MOUNT BACK SIDE CHANNELS

1. Align back channel under corner of fascia bracket so the side of the back channel is ush

with the bracket

2. Mark mounting screw hole locations with a center punch

3. Pre-drill holes in the side of channels using metal drill bit

4. Re-align the back channel. Use a level to ensure side channels are straight and leveled.

5. Mount with the correct mounting screws.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the tab (foot) in the middle of the bracket.

2. Set the post of the idler end into the V-slot of the idler side bracket. Rotate the T-hook over the post on the idler side bracket to lock

in the post and secure the fabric roll.

INSTALL FRONT SIDE CHANNEL

1. Install front side channel by engaging lip of the channel into the

groove on the back side channel. Snap front side channel into place.

INSTALL BOTTOM CHANNEL (if ordered)

1. Place left side of bottom channel between front and back side channels.

2. Slide the right side down in between the front and back side channels until the bottom

closure sits on the window sill. Mount bottom channel to window sill using mounting screws.

ATTACH FASCIA

1. Control side bracket attaches to the side of the panel with the notch.

The idler side bracket goes on the side without the notch.

2. Place the top of the fascia panel into the top indention of the brackets. Rotate the panel down

and snap it into place.

7

Engage lip into groove Snap into place

Back

Channel

Front

Channel

Front

Channel

Back

Channel

Click

Shades with 4” Fascia — INSIDE MOUNT

INSTALL MOUNTING BRACKETS

1. Insert bracket into the pocket. Attach end plate onto the side bracket.

2. Using appropriate screws, install pocket into top or window frame.

NOTE: If shade is ordered with side and/or bottom channel please go to Side/Bottom Channel Installation Instructions.

If not, skip to Install the Shade.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the tab (foot) in the middle of the control side bracket.

2. Set the post of the idler end into the V slot of the idler side bracket. Rotate the T-hook

over the post on the idler side bracket to lock in the post and secure the fabric roll.

3. Install Bottom Closure into the pocket on an angle.

Once aligned, allow front of bottom closure to drop in place.

See Side/Bottom Channel Installation Instructions on page 9.

8

Flush Mounting Depth Requirement: 4-9/16”

Min. Mounting Depth Requirement: 3-5/8”

Shades with Pocket — INSIDE MOUNT

Side/Bottom Channel Installation Instructions

MOUNT BACK SIDE CHANNELS

• Mount Back Side Channels by aligning the back channel ush with the back of the pocket and mount with the correct mounting screws.

INSTALL THE SHADE

• To install the shade, insert control side rst by placing the hole in the core into the tab (foot) in the middle of the bracket. Set the post of the

idler end into the V slot of the idler side bracket. Rotate the T-hook over the post on the idler side bracket to lock in the post and secure

the fabric roll.

INSTALL FRONT SIDE CHANNEL

• Install Front Side Channel by engaging lip of channel into the groove on the back side channel. Snap front side channel into place.

INSTALL BOTTOM CHANNEL (if ordered)

• To install Bottom Channel (if ordered), place left side of bottom channel between front and back side channels. Slide the right side down

in between the front and back side channels until the bottom closure sits on the window sill. Mount bottom channel to window sill using

correct mounting screws.

• Install Bottom Closure into the pocket on an angle. Once aligned, allow front of bottom closure to drop in place.

9

Engage lip into groove Snap into place

Front

Channel

Back

Channel

Front

Channel

Back

Channel

Shades with Pocket — INSIDE MOUNT

MOUNT THE CORNICE

1. Center the cornice in desired location.

2. Mark 2” from each jamb for screw location. Mark the mounting surface using a pencil. Center the marks in the bracket slots.

• Space screws evenly, but no more than 24” apart.

3. Drill screw holes.

IMPORTANT: Use drywall anchors when mounting into drywall.

4. Install the cornice through the slotted angle bracket to the

mounting surface with the #8 x 1-1/4” screws provided.

To install shade behind the cornice – refer to instruction under No Top Treatment

• Install the valance rst and then proceed with shade installation.

• The valance can be mounted directly with the provided installation screws, drill vertically through the pre-drilled slots

into the top of the window frame.

To install shade behind the valance – refer to instruction under No Top Treatment.

10

Slotted Angle

Bracket

Slotted Angle

Bracket

Cornice not

shown for

clarity

Inside Mount Screws Required

Width # of Screws

12” – 28” 3

28-1/8” – 52” 4

52-1/8” – 76” 5

76-1/8” – 100” 6

100-1/8” – 120” 7

120-1/8” – 144” 8

Space Evenly Space Evenly

Jamb Jamb

At least 2” At least 2”

Slotted

Angle

Flush Mount Depth Requirement: 1-1/2”

Min. Mounting Depth Requirement: 1”

Flush Mount Depth Requirement: 3-1/8”

Min. Mounting Depth Requirement: 1-1/4”

Shades with Fabric Cornice — INSIDE MOUNT

Shades with Deluxe Valance — INSIDE MOUNT

11

All Operating Systems

• Determine the control side. Bracket (B) with tab (foot) should be at the control side and the bracket (A) with V slot

and T-Hook should be at the idler side.

• The installation brackets are always mounted so that the inner surfaces face each other. Make sure all brackets are leveled and aligned.

• Insert control side into the foot of the bracket.

• Set the post of the idler end into the V slot of the idler side bracket. Rotate the T-hook on the idler side bracket over the post to lock in the

post and secure the fabric roll.

• Measure correct spacing

• Install brackets – face x wall mount, top x ceiling mount.

Brackets must be in line and level.

• Shim brackets if necessary.

To Remove the shade:

• Reverse the steps above.

Min. Mounting Surface Height Requirement: 1-3/4”

Min. Mounting Surface Height Requirement: 4”

End Cap (attached at factory)

V Slot Tab

(Foot)

(A)

(B)

Shades with Square Cassette — OUTSIDE MOUNT

Shades with No Top Treatment — OUTSIDE MOUNT

Small Cassette

Figure A - Position the cassette valance so the ridge engages into the top lip of all brackets.

Figure B - Rotate the bottom front of the cassette valance upwards and towards the bracket

until the rear of the cassette valance engages into the bracket and snaps into place, as shown.

To remove the shade

• Hold the cassette at each bracket tab to disengage the rear of the cassette.

Medium/Large Cassette

• Space brackets evenly. Using the installation bracket as a template, measure to the center

of the brackets and mark the hole locations with a pencil for drilling.

• Install the brackets, make sure all brackets are leveled. Mount the shade.

Figure A - Position and securely engage rear of the cassette into the bottom hooks of the bracket.

Rotate cassette upward (1) and push backward (2).

Figure B - Hold the cassette release gently (3) to ensure the top of the cassette engaging into

the top lips of all brackets, as shown.

To remove the shade

• Hold the cassette, gently insert a athead screwdriver in between the top of the cassette

and each bracket tab to assist in releasing the cassette from the top bracket lips.

Push the cassette toward the back. Rotate downward to disengage the cassette.

12

Min. Mounting Surface Height Requirement:

• 2-3/4” (small curved cassette)

• 3-1/8” (medium curved cassette)

• 4” (large curved cassette)

Release Tab

Shades with Curved Cassette — OUTSIDE MOUNT

INSTALL THE MOUNTING BRACKETS

The open end of each bracket faces downward, as shown in the image.

• Attach each bracket to the mounting surface using the two holes in the rear of each bracket.

• Use a level to make sure brackets are leveled.

INSTALL THE SHADE

• Insert control side of the fabric roll into the tab (foot) in the middle of the bracket.

• Set the post of the idler end into the V slot of the idler side bracket.

Rotate the T-hook on the idler side bracket to lock in the post and secure the fabric roll

INSTALL THE FASCIA

• Please note, do not install fascia panel until shade is installed. Then assemble the two end brackets and the fascia panel.

• Place the top of the fascia panel into the top indention of the brackets. Rotate the panel down and snap it into place.

• Attach bracket end plate to the brackets.

1313

Min. Mounting Depth Requirement: 3”

Fascia

Panel Rotator - Side

Bracket

Tab

Top/Rear Cover

Removed for Clarity

Shades with 3” Fascia — OUTSIDE MOUNT

INSTALL THE MOUNTING BRACKETS

The open end of each bracket faces downward, as shown in the image. The bracket with a tab (foot) in the middle should be at the control side

and the bracket with V slot and T-Hook should be at the idler side.

• Mount brackets to the wall using the two holes in the rear of each bracket for wall mount. For ceiling mount, mount brackets

to the ceiling using two holes in the top of each bracket.

• Use a level to make sure brackets are leveled.

NOTE: If shade is ordered with Side and/or Bottom Channel, please refer to Side/Bottom Channel Installation Instructions.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the tab (foot) in the middle of the bracket.

2. Set the post of the idler end into the V slot of the idler side bracket. Rotate the T-hook over the post on the idler side bracket to lock

in the post and secure the fabric roll.

ATTACH THE FASCIA

3. Place the top of the fascia panel into the top indention of the brackets. Rotate the panel down and snap it into place.

See Side/Bottom Channel Installation Instructions on page 15

14

Min. Mounting Depth Requirement: 4” Tab

Top/Rear Cover

Removed for Clarity

Shades with 4” Fascia — OUTSIDE MOUNT

Side/Bottom Channel Installation Instructions

MOUNT BACK SIDE CHANNELS

1. Align back channel under corner of fascia bracket so the side of the back channel

is ush with the bracket.

2. Mark mounting screw hole locations with a center punch

3. Pre-drill holes in the side of channels using metal drill bit as shown.

4. Re-align the back channel. Use a level to ensure side channels are straight and leveled.

5. Mount with the correct mounting screws.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the foot of the control side bracket.

2. Set the post of the idler end into the V slot of the idler side bracket. Rotate the T-hook over the post on the idler side bracket to lock

in the post and secure the fabric roll.

INSTALL FRONT SIDE CHANNEL

1. Install front side channel by engaging lip of the channel into the groove

on the back side channel. Snap front side channel into place.

INSTALL BOTTOM CHANNEL (if ordered)

1. Place left side of bottom channel between front and back side channels.

2. Slide the right side down in between the front and back side channels until bottom

closure is at the bottom of the side channels. White holding the bottom channel in

place, drill a screw hole using a metal drill bit (1” from the side and 3/8” from bottom

corner). Install mounting screw through all channels and into the wall.

ATTACH FASCIA

1. The control-side bracket attaches to the side of the panel with the notch. The rotator side bracket

goes on the side without the notch.

2. Place the top of the fascia panel into the top indention of the brackets. Rotate the panel down

and snap it into place.

3. Attach bracket end plate to the brackets.

1515

Engage lip into groove Snap into place

Back

Channel

Front

Channel

Front

Channel

Back

Channel

1” from side

3/8” from bottom

Click

Shades with 4” Fascia — OUTSIDE MOUNT

16

INSTALL POCKET & MOUNTING BRACKETS

1. Mount pocket to ceiling using the appropriate mounting screws.

2. Pre-drill mounting holes, and use anchor if needed.

3. Make sure all brackets are level.

4. Insert bracket into the pocket (use mallet to gently tap bracket into place)

until ush with the end of the pocket. Secure bracket to pocket with

supplied mounting screws.

5. Secure end plate to the pocket

NOTE: If shade is ordered with side and/or bottom channel please go to Side/Bottom Channel Installation Instructions.

If not, skip to shade installation.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the tab (foot) in the middle of the control side bracket.

2.Set the post of the idler end into the V slot of the idler side bracket. Rotate the T-hook

over the post on the idler side bracket to lock in the post and secure the fabric roll.

3. Install Bottom Closure into the pocket on an angle.

Once aligned, allow front of bottom closure to drop in place.

See Side/Bottom Channel Installation Instructions on page 17.

Min. Mounting Surface Height Requirement: 4-1/2”

Shades with Pocket — CEILING MOUNT

17

Side/Bottom Channel Installation Instructions

MOUNT BACK SIDE CHANNELS

1. Align back channel under corner of fascia bracket so the side of the back channel

is ush with the bracket.

2. Mark mounting screw hole locations with a center punch.

3. Pre-drill holes in the side of channels using metal drill bit as shown.

4. Re-align the back channel. Use a level to ensure side channels are straight and leveled.

5. Mount with the correct mounting screws.

INSTALL THE SHADE

1. Insert control side of the fabric roll into the tab (foot) in the middle of the control side bracket.

2. Set the post of the idler end into the V slot of the idler side bracket.

Rotate the T-hook over the post on the idler side bracket to lock in the post

and secure the fabric roll.

INSTALL FRONT SIDE CHANNEL

1. Install front side channel by engaging lip of the channel into the

groove on the back side channel. Snap front side channel into place.

INSTALL BOTTOM CHANNEL (if ordered)

1. Place left side of bottom channel between front and back side channels.

2. Slide the right side down in between the front and back side channels until bottom closure is at the bottom of the side channels.

White holding the bottom channel in place, drill a screw hole using a metal drill bit (1” from the side and 3/8” from bottom corner).

Install mounting screw through all channels and into the wall.

3. Install Bottom Closure into the pocket on an angle. Once aligned, allow front of bottom closure to drop in place.

1” from side

3/8” from bottom

Engage lip into groove Snap into place

Back

Channel

Front

Channel

Front

Channel

Back

Channel

Shades with Pocket — OUTSIDE MOUNT

1. Attach the returns to the cornice.

• Check the angle on each return.

• Fasten screws into the cornice.

• Repeat for opposite return.

2. Skip to next step if ordered with a shade. If ordered custom returns under Fabric Cornice Only

(without shade), place the 8” bracket on top of the slotted angle next to the return. With the back

of the bracket ush with the back edge of the return, mark the cut mark just past the screw hole

that lines up with the slotted angle. Then cut the bracket at the mark.

3. Measure distance from top edge of cornice to the rst complete hole in the slotted angle. Use that measurement to mark the location

for the rst bracket at the desired height. Repeat for the opposite bracket.

• Space brackets evenly, but no more than 24” apart.

4. Drill the screw holes. (Use drywall anchors when needed)

5. Attach the installation brackets with the screws provided.

• Ensure the mounting surface is level and the brackets are aligned. Shim brackets, if needed.

6. Using the bolts and nuts provided, attach the slotted angle on top of the installation brackets

See Install the Dust Cover (Outside Mount Only) on page 19.

Shades with Fabric Cornice — OUTSIDE MOUNT

18

Return

(Outside Mount Only)

Installation Bracket

(Outside Mount Only)

Slotted

Angle

Bracket

Bolt &

Nut

Dust Cover

Support

Dust Cover

Outside Mount Screws Required

Width # of Screws

12” – 28” 2

28-1/8” – 52” 3

52-1/8” – 76” 4

76-1/8” – 100” 5

100-1/8” – 120” 6

120-1/8” – 144” 7

Min. Mounting Surface Height Requirement: 2”

Space Evenly Space Evenly

Measure

this distance

Bracket

Measure

this distance

Measure

this distance

Bracket Use the distance measured

in the previous step.

Cornice not

shown for

clarify

Mark/Cut

This Line

Install the Dust Cover (Outside Mount Only)

• Dust cover only comes with cornice 1-1/2”, 4” & 6” return.

7/8” Dust Cover

• Remove adhesive backing from square tapes

• Place the square tapes on slotted angle

• Put the dust cover on top of slotted angle and press it to secure the adhesive.

3-7/8” & 5-7/8” Dust Cover

• Snap the dust cover support onto the slotted angle as shown

• Remove adhesive backing from square tapes

• Place the square tapes on slotted angle and brackets

• Press the dust cover in place to secure the adhesive

To install shade behind the cornice – refer to instruction under No Top Treatment.

1. Install the valance rst and then proceed with shade installation.

2. Use anchors if needed, spaced brackets evenly. Using the installation bracket as a template, measure to the center of the brackets

and mark the hole locations with a pencil for drilling.

3. Brackets must be in line and level. Shim brackets if necessary.

4. Mount the brackets with the screws provided, slide the valance under the clips that are on the top of the installation brackets.

To install shade behind the valance – refer to instruction under No Top Treatment.

19

Refer to motorization programming instructions provided for more details.

Dust

Cover

Dust

Cover

Press

Snap support

onto slotted angle.

Dust Cover

Support

Slotted

Angle Tape

Squares

Dust Cover

Support Tape

Squares

Dust Cover

Remove adhesive

backing from

both sides.

Peel

Min. Mounting Surface Height Requirement: 2”

Remove adhesive

backing from

both sides.

Peel

Shades with Fabric Cornice — OUTSIDE MOUNT

Shades with Deluxe Valance — OUTSIDE MOUNT

Motorized Shades

If your shade does not roll up evenly (telescoping)

• First check the mounting brackets are aligned and level. (Please use a leveling device to check)

IF shade STILL does not roll evenly.

• Unroll the shade until you can see where the fabric is attached to the roller tube.

• Place a small piece of evenly cut masking tape at the opposite end from where the fabric gathers (telescoping).

• A second or even third piece can be placed until shade is rolled up evenly.

Roller Shades are made of the highest quality materials for extended wear. If it is not damaged or exposed to a great deal of direct sunlight, it is not

unrealistic to expect years of enjoyment with minimal care. Raising and lowering shades periodically helps reduce most natural dust accumulation.

If additional cleaning is desired, regular dusting with a feather duster or carefully cleaned with a soft vacuum brush attachment.

Fabric: Vacuum your roller shade frequently. This will keep your roller shade looking like new! If your roller shade becomes soiled use a high-quality

foam upholstery cleaner.

Transparent and Vinyl: Transparent and vinyl shades can be readily cleaned with any standard commercial window spray cleaner, which should

be diluted with 10 parts water to 1 part cleaning solution. For best results, shades should be removed from brackets, then placed on a clean, at

covered surface. To prevent streaking and inconsistent drying, wash and dry one small area at a time. Do not rub hard. Use a soft, lint-free cloth for

washing and drying.

20

Immediately remove this product if a cord longer than 22 cm or a loop

exceeding 44 cm around becomes accessible.

Rev 7/21 Print 7/21

WARNING

RISQUE D’ÉTRANGLEMENT–

Les enfants en bas âge

MISE EN GARDE

peuvent s’étrangler avec des cordes. Enlevez immédiatement ce produit si une

corde mesurant plus de 22 cm devient accessible ou si le contour d’une boucle de

plus de 44 cm devient accessible.