SUN GLOW Roller Shade Savalan Window Decor Manuel utilisateur

Roller Shade Savalan Window Decor
Marque
SUN GLOW
Modèle
Roller Shade Savalan Window Decor
Taper
Manuel utilisateur
www.mysunglow.com
Installation Instructions | Open Roll | 202-04-29 1 of 4
Open Roll Roller Shade
Installation Instructions
WARNING MISE EN GARDE
STRANGULATION HAZARD — Young children
can be strangled by cords. Immediately remove this
product if a cord longer than 22 cm or a loop
exceeding 44 cm around becomes accessible.
RISQUE D’ÉTRANGLEMENT — Les enfants en bas
âge peuvent s’étrangler avec des cordes. Enlevez
immédiatement ce produit si une corde mesurant
plus de 22 cm devient accessible ou si le contour
d’une boucle de plus de 44 cm devient accessible.
1PREPAR ATION
A
B
B
C
C
D
Component List
A. Shade
B. Universal Mounting Bracket
C. Bracket Cover (Optional)
D. Chain Tension Device
2MOUNT THE BRACKETS
Brackets are universal and are capable of receiving both the clutch and pin end.
CEILING MOUNT WALL MOUNT LATERAL MOUNT
Roller Shade - Open Roll
Installation Instructions
www.mysunglow.com
Installation Instructions | Open Roll | 202-04-29 2 of 4
3
INSTALL THE SHADE
NOTE: For shades with Zero Gravity, please refer to Zero Gravity instructions on page 3 at this stage.
STEP 3A:
INSTALL PIN END FIRST
STEP 3B:
INSTALL CLUTCH END
Put the spring loaded Pin End into the hole in the bracket. Keeping gentle pressure against the Pin End lift the clutch up and
align the two hooks on the clutch with the two slots in the bracket.
The hooks should fall into place in the bracket, pull down gently to
secure the blind into the bracket.
**The bottom of the Clutch should point straight down.
4INSTALL BRACKET COVERS (OPTIONAL)
If you were supplied with bracket covers, install them by sliding them on to the mounting brackets.
5INSTALL THE SAFETY SHIELD
NOTE: For shades with chain operation only.
Ensure that Safety Shield is carefully and properly installed.
www.mysunglow.com
Installation Instructions | Open Roll | 202-04-29 3 of 4
Zero Gravity - Fascia or Open Roll Instructions
These steps are not required for Zero Gravity in Curved Cassettes.
Skip these steps if using chain, Neo, or motorized control
If the Pin End of the shade
appears as shown here,
proceed with Steps 1,2
& 3 before returning to
Step 4 of the Open Roll
Installation Instructions
If the Pin End of the shade
appears as shown here,
proceed with Steps 4,5
& 6 before returning to
Step 4 of the Open Roll
Installation Instructions
1PREPARING FOR INSTALLATION
NOTE: The blue shipping lock is used to
lock the tension in place during shipping.
Remove shipping lock before installing
Hex Plunger
2INSTALLING THE SYSTEM
(A) Insert the pin end of the blind into the bracket.
(B) Insert the hooked end into the other side bracket, and ensure the Zero Gravity head sits on the hooked
teeth firmly. This should compress the hex plunger which releases the tension onto the shade.
A
Push
BPush
3TESTING THE SYSTEM
Always operate the shade from the center of the bottom bar. Ensure that the shade is balanced and
does not want to roll up or down on its own. If it does, then the spring will require more or less tension to
be perfectly balanced. If the shade requires more tension, turn the zero gravity head into the fabric, ie
opposite direction to the fall of the fabric.
Insert for 5mm hex
(only for outside mount)
Adjusting Spanner
www.mysunglow.com
Installation Instructions | Open Roll | 202-04-29 4 of 4
Zero Gravity Mini - Pin Lock Instructions
These steps are not required for Zero Gravity in Curved Cassettes.
Skip these steps if using chain, Neo, or motorized control
WARNING
• Do not pull pin lock out until shade is installed or tension will be released.
• If tension has been released, see trouble shooting.
1RUBBER BAND REMOVAL
Before installing the shade remove the rubber band holding the Pin Lock in place.
AB
2INSTALL SHADE AND REMOVE PIN LOCK
C: Install roller shade while keeping Pin
Lock toward you and held in place.
D: After installation remove the pin lock
C D
3TESTING THE INSTALLED ROLLER SHADE
Installed roller shade must be operated
smoothly by the centre of the bottom
bar to avoid excessive telescoping
TROUBLE SHOOTING:
ONLY REQUIRED IF TENSION IS RELEASED
If the tension is released or removed accidentally follow these instructions:
The tension can be put back in any Zero Gravity Mini by turning the clutch head in the
opposite direction of the fabric approximately 1 – 2 full rotations. While holding tension,
insert the Pin Lock into the hole of the clutch. PROCEED WITH STEP 2 WHEN FINISHED.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

SUN GLOW Roller Shade Savalan Window Decor Manuel utilisateur

Roller Shade Savalan Window Decor
Marque
SUN GLOW
Modèle
Roller Shade Savalan Window Decor
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents