Dorel Home WM3921FP Assembly Manual

Taper
Assembly Manual
11
Thank you for purchasing from DHP!
Date of Purchase
G.Y. - 2023/07/29
WM3921E2 (Mocha), WM3921W-DC (White),
WM3921G-DC (Gray), WM3921B-DC (Black),
WM3921SG (Sage Green), WM3921FP (Fancy Pine)
Bunk Bed
Twin / Twin
Lot Number (TAKEN FROM CARTON)
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY
INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
B34WM392100-100063
2023 Dorel Home Products All Rights Reserved
Weight Limit : 165 Lb / 75 Kg per level
If parts are missing or damaged, we will gladly ship your
replacement parts free of charge.
Visit www.dhpfurniture.com/eng/replacement-parts
or call Toll-Free 1-800-267-1739
You can also chat with us at www.dhpfurniture.com
Questions, concerns, missing parts?
CONTACT OUR CUSTOMER SERVICE
DEPARTMENT BEFORE RETURNING PRODUCT
TO THE RETAILER.
22
Limited 1 year Warranty
DHP warrants this product to be free from defects in material and workmanship
and agrees to remedy any such defect. This warranty covers one year from the
date of original purchase from authorized retailers. This is solely limited to the
repair or replacement of defective parts and assembly labor is not included.
This warranty does not apply to any product which has been improperly
assembled, subjected to misuse or abuse or which has been altered or repaired
in any way.The warranty does not cover wearing, tearing, fading or splitting of the
fabric (where applicable). Liability for consequential damages is excluded to the
extent exclusion is permitted by law. This warranty gives you specific legal rights
and you may also have other rights which vary from state to state or province to
province.
To obtain warranty service, purchaser must present original bill of sale.
Components repaired or replaced are warranted through the remainder of the
original warranty period only. The defective components will be repaired or
replaced without charge, subject to the terms and conditions described above.
The terms and conditions of the limited warranty are subject to change without
notice. For the latest warranty policy, please visit www.dhpfurniture.com.
Work in a spacious area and near where the unit will be used, preferably on a
carpet, or use a piece of the cardboard packaging to protect your floor and
product.
Make sure all parts are included. Most parts are labeled or stamped on the raw
edge.
Read each step carefully. It is very important that each step of the instructions is
performed in the correct order. If these steps are not followed in sequence,
assembly difficulties will occur.
This product may contain small components. Please ensure that they are kept
away from small children.
This product is designed for home use and is not intended for commercial use.
Contact Us!
For help with assembly, identifying parts, product information or to order parts,
please contact us: This product is shipped in
1 carton
www.dhpfurniture.com
Do NOT use
powertools
Phillips head screwdriver
needed (not included)
1 hour
Read Before Beginning Assembly
cs@dhpfurniture.com
1-800-267-1739
DHP Consumer Services
12345 Albert Hudon, Suite 100,
Montreal, Quebec H1G 3L1
33
STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed;
for example, but not limited to, hooks, belts and jump ropes.
WARNINGS - Bunk Bed: Twin / Twin
Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.
The mattress platform is designed to support a mattress without the need for a posture board or box spring.
Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.
USE ONLY A COIL SPRING MATTRESS ON THE UPPER BUNK. FAILURE TO DO SO CAN RESULT IN INJURY.
Use only mattresses which are 74"-75" long and 37 1/2" - 38 1/2" wide on upper and lower bed. Ensure thickness of mattress does not exceed
6"(152mm). Surface of mattress must be at least 5"(127mm) below the upper edge of guardrails.
Do not allow children under 6years of age to use the upper bunk.
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length
of the bed should be placed against the wall to prevent entrapment between the bed and wall (applicable for bunk beds with full length
guardrails on one side).
Periodically check and ensure that the guardrail, ladder and other components are in their proper position, free from damage, and that all
connectors are tight.
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
Use of a night light may provide added safety precaution for a child using the upper bunk.
The use of water or sleep flotation mattresses is prohibited.
Always use the ladder for entering and leaving the upper bunk.
Prohibit more than one person on upper bunk.
Keep these instructions for future reference.
44
PARTS
A
B
L
T
N
D
E
G
F
R
M
C
Q
I
O
P
S
K
J
H
55
PARTS LIST
TOP POST
2 PCS
TOP POST
1 PC
TOP POST
1 PC
BOTTOM POST
2 PCS
BOTTOM POST
2 PCS
HEADBOARD TOP CROSS
4 PCS
HEADBOARD BOTTOM CROSS
4 PCS TOP SIDE RAIL (WITH 3 HOLES)
1 PC
A
HGF
D
C
B
E
66
PARTS LIST
BOTTOM SIDE RAIL (WITH 2 HOLES)
1 PC
TOP SIDE RAIL (WITH 1 HOLES)
1PC
BOTTOM SIDE RAIL (WITH NO HOLES)
1 PC
SLAT
12 PCS
LONG GUARDRAIL
2 PCS
SHORT GUARDRAIL
2 PCS
LONG LADDER END
1 PC
SHORT LADDER END
1 PC
LADDER STEP
4 PCS
GUARDRAIL LEG
2 PCS
HEADBOARD CENTER CROSS
4 PCS
SLAT
4 PCS
I
M
Q R S T
PO
L
K
N
J
77
Each part has a unique part number. Please
reference the appropriate part number when
contacting customer service for replacement parts.
Before throwing any packaging, please
verify all contents and make sure you
have received all the parts listed above!
PART UNMBERS
PART
LABELS
WM3921E2
(Mocha) WM3921W-DC
(White)
WM3921G-DC
(Gray)
WM3921B-DC
(Black)
WM3921SG
(Sage Green)
WM3921FP
(Fancy Pine)
A WM3921E2-A WM3921W-DC-A WM3921G-DC-A WM3921B-DC-A T1028820 T1031600
B WM3921E2-B WM3921W-DC-B WM3921G-DC-B WM3921B-DC-B T1028830 T1031610
C WM3921E2-C WM3921W-DC-C WM3921G-DC-C WM3921B-DC-C T1028840 T1031620
D WM3921E2-D WM3921W-DC-D WM3921G-DC-D WM3921B-DC-D T1028850 T1031630
E WM3921E2-E WM3921W-DC-E WM3921G-DC-E WM3921B-DC-E T1028860 T1031640
F WM3921E2-F WM3921W-DC-F WM3921G-DC-F WM3921B-DC-F T1028870 T1031650
G WM3921E2-G WM3921W-DC-G WM3921G-DC-G WM3921B-DC-G T1028880 T1031660
H WM3921E2-H WM3921W-DC-H WM3921G-DC-H WM3921B-DC-H T1028890 T1031670
I WM3921E2-I WM3921W-DC-I WM3921G-DC-I WM3921B-DC-I T1028900 T1031680
J WM3921E2-J WM3921W-DC-J WM3921G-DC-J WM3921B-DC-J T1028910 T1031690
K WM3921E2-K WM3921W-DC-K WM3921G-DC-K WM3921B-DC-K T1028920 T1031700
L WM3921E2-L WM3921W-DC-L WM3921G-DC-L WM3921B-DC-L T1028930 T1031710
M WM3921E2-M WM3921W-DC-M WM3921G-DC-M WM3921B-DC-M T1028940 T1031720
N WM3921E2-N WM3921W-DC-N WM3921G-DC-N WM3921B-DC-N T1028950 T1031730
O WM3921E2-O WM3921W-DC-O WM3921G-DC-O WM3921B-DC-O T1028960 T1031740
P WM3921E2-P WM3921W-DC-P WM3921G-DC-P WM3921B-DC-P T1028970 T1031750
Q WM3921E2-Q WM3921W-DC-Q WM3921G-DC-Q WM3921B-DC-Q T1028980 T1031760
R WM3921E2-R WM3921W-DC-R WM3921G-DC-R WM3921B-DC-R T1028990 T1031770
S WM3921E2-S WM3921W-DC-S WM3921G-DC-S WM3921B-DC-S T1029000 T1031780
T WM3921E2-T WM3921W-DC-T WM3921G-DC-T WM3921B-DC-T T1029010 T1031790
88
HARDWARE LIST
Ø 1/4" x 100mm Ø 6.5mm x 48mm Ø 6.5mm x 100mm
JOINT CONNECTOR
(4mm hex head)
16 PCS
WOOD JOINT CONNECTOR
(4mm hex head)
14 PCS
WOOD JOINT CONNECTOR
(4mm hex head)
22 PCS
Ø 4mm x 35mm Ø 4mm x 30mm Ø 19mm x 95mm Ø 10mm x 50mm
FLAT HEAD SCREW
24 PCS
FLAT HEAD SCREW
6 PCS
WOOD DOWEL
4 PCS
WOOD DOWEL
62 PCS
Ø 11.8mm x 15mm
BARREL NUT
16 PCS
ALLEN KEY
1 PC
Hardware Pack
Please do not completely tighten all the hardware, until the entire assembly
is complete, unless otherwise indicated in the step-by-step instructions.
The screw(s), bolt(s) to be used at each step are
shown in actual size in the lower right corner of the page.
WM3921E2 (Mocha),
WM3921G-DC (Gray),
WM3921B-DC (Black)
HP#: TWM3921E2-00
WM3921W-DC (White),
WM3921SG (Sage Green) HP#: TWM3921N-DC-00
WM3921FP (Fancy Pine ) HP#: TWM3921FP-00
❹❺
❽❾
99
Step 1
One of the top cross Fhas a label on it, Use it
during this step.
Insert wood dowels into the ends of the top
cross Fx2, center cross Sx2 and bottom crosses
Gx2.
Attach posts A &B, A &Cto the crosses using
the wood joint connectors as shown.
Use the Allen key to tighten all
joint connectors.
X8X24
Warning label side face inward F
F
G
G
B
C
A
A
S
1010
Step 2
Insert wood dowels into the ends of top cross
Fx2 and center cross Sx2 and bottom crosses
Gx2.
Attach posts D & Eusing wood joint connectors
though crosses F, S& G.
X8
X24
F
F
G
G
E
E
D
S
D
1111
Step 3
Insert barrel nuts into side rails I & Kas
shown below.
Attach the rails I & Kto the posts D &E using
joint connectors .
X8X8
D
E
D
E
I
K
1212
Step 4
Insert wood dowels into each end of the
guardrails Mx2. Insert barrel nuts into side
rails H & Jas shown below.
Attach the long guardrails M to posts B &Aand
secure using joint connectors .
Attach the rails H & Jto the posts A, B &C
using joint connectors .
X4X4 X8
X8
Holesonthisside
C
A
A
B
H
J
M
1313
Step 5
Place wood dowels into the holes in the
posts Dx2 & Ex2.
Stack the top bunk onto the bottom bunk with
the help of another person.
X4
B
E
A
D
E
C
D
A
1414
Step 6
Insert wood dowels into the ends of the
ladder steps Qx4.
Attach ladder ends O &P to ladder steps Qwith
wood joint connectors .
X8X8
P
Q
O
1515
Step 7
Attach the ladder to the side rails H & Iwith
wood joint connector as shown.
X4
I
H
Q
P
1616
Step 8
Insert wood dowels in the ends of short
guardrails N, Attach short guardrails N to top
post A with wood joint connectors .
Attach the ladder to the short guardrails N with
wood joint connectors as shown.
Attach the guardrail leg Rto M,N,J & Hwith flat
head wood screws .
Use a Phillips head screwdriver (not included)
to install all screws.
X2X2
X2X6
N
A
M
R
H
J
O
1717
Step 9
Insert slats with wood dowel Tx4 into the center
slots of the side rails I & K and H & Jof the bunk
as shown.
Attach slats without wood dowel Lx12 onto side
rails I & K and H & Jof the bunk with flat head
screws .
X24
K
L
I
T
1818
Bottombed
consistsofa
headboardof
onebed.
Aswellasthe
headboardofthe
secondbed.
Topbedconsists
ofafootboard
ofonebed.
Aswellasthe
footboardofthe
secondbed.
Thefirsttwinbed.
Thesecondtwinbed.
Separating the beds
Remove the ladder and all the guardrails.
With the help of another person, remove the top
bunk from the lower bunk.
Disassemble the side rails from all headboards
(top and lower bunks).
Re-assemble the headboards (with tall posts) and
footboards (with short posts) to side rails.
Note: Switching the headboards will allow the two
single beds to be identical (the headboards will
have taller posts and the footboards will have the
shorter posts).
1919
Move your new furniture carefully, with two
people lifting and carrying the unit to its new
location.
Your furniture can be disassembled and
reassembled to move.
Dust this item regularly with a soft, lint- free
cloth to prevent soil build up. Do not soak or
wash in hot water. Wipe with a soft, damp cloth
if necessary. Do not use abrasives, cleansers or
polish.
Check bolts and nuts periodically and tighten if
necessary.
Helpful Hints
CAUTION: This unit is intended for use only with the products and/or maximum
weights indicated. Use with other products and/or products heavier than the
maximum weights indicated may result in instability or cause possible injury.
That's it ! You've finished assembling your Bunk Beds!
Weight Limit: 165 Lb / 75 Kg per level
ESES
Fecha de compra Número de lote
ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE
SEGURIDAD. POR FAVOR LEA Y GUARDE PARA SU REFERENCIA FUTURA.
DHP garantiza que este producto está libre de defectos de material y mano de obra y se
compromete a remediar cualquier defecto de este tipo. Esta garantía cubre 1 año a partir de la
fecha de compra original. Esta garantía es válida solamente con presentación de una prueba
de compra. Esto se limita a la reparación o reemplazo de componentes defectuosos del mueble
y no se incluye ningún trabajo de ensamblaje.
Esta garantía no se aplica a ningún producto que haya sido mal ensanblado, sujeto a mal uso o
abuso, o que haya sido alterado o reparado de cualquier manera. Cualquier uso, rotura o
pérdida de color de la tela no están incluidos en esta garantía (donde corresponda). Esta
garantía le da derechos legales específicos y usted puede también tener otros derechos que
varían de estado a estado o de provincia a provincial.
Para obtener el servicio de garantía, debe presentar la factura original de su compra. Los
componentes reparados o reemplazados están garantizados durante el periodo original de la
garantía. Las partes defectuosas serán reparadas o reemplazadas sin cargo extra y sujetas a
los términos y condiciones descritos anteriormente. Los términos y condiciones de la garantía
limitada están sujetos a cambios sin previo aviso. Para conocer la política de garantía más
reciente, visite www.dhpfurniture.com.
Información sobre la garantía
¡Gracias por tu compra DHP!
Este producto está diseñado para uso doméstico y no para uso comercial.
ADVERTENCIA PARA NIÑOS PEQUEÑOS - Este producto contiene
componentes pequeños. Por favor asegúrese de que las piezas estén fuera del
alcance de los niños.
No utilice herramientas eléctricas para ensamblar su mueble. Este tipo de
herramientas pueden rasgar o dañar las partes.
Precauciones
Lea antes de comenzar a ensamblar
Llame a nuestro número gratuito si necesita asistencia.
Trabaje en un área espaciosa y cerca de donde su producto será utilizado,
preferiblemente sobre una alfombra o utilice el cartón del empaque para
proteger su piso y su producto.
El número de personas recomendadas para el montaje de este producto
es: 1 (sin embargo, es recomendable contar con ayuda adicional).
Tiempo estimado de ensamble es 1 hora.
Asegúrese de que todas las partes están incluidas. La mayoría de las partes
están etiquetadas o selladas en los bordes.
Lea cada paso cuidadosamente. Es muy importante que cada paso de las
instrucciones sea realizado en el orden correcto. Si estos pasos no se siguen
en secuencia, pueden ocurrir dificultades durante el ensamblado.
¡Contáctenos !
Para solicitar ayuda con el ensamblaje, identificación de partes, información del
producto o simplemente ordenar otras partes, diríjase a:
Chatea con nosotros: www.dhpfurniture.com
1-800-267-1739
DHP Servicio al Cliente
12345 Albert Hudon, Suite 100, Montreal, Quebec, Canada, H1G 3L1
Individual / Individual
Litera
Preguntas, inquietudes, partes que faltan? CONTACTE A
NUESTRO DEPARTAMENTO DE SERVICIO AL CLIENTE ANTES
DE DEVOLVER EL PRODUCTO A LA TIENDA.
Si le faltan piezas o las que se incluyen están dañadas, con mucho gusto le
enviaremos sus piezas de reemplazo sin cargo extra.
Visite www.dhpfurniture.com/spa/replacement-parts, llame gratis al
1-800-267-1739 o chatea con nosotros en www.dhpfurniture.com
WM3921E2 (Mocha), WM3921W-DC (Blanco),
WM3921G-DC (Gris), WM3921B-DC (Negro),
WM3921SG (Verde Salvia), WM3921FP (Pino de lujo)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33

Dorel Home WM3921FP Assembly Manual

Taper
Assembly Manual

dans d''autres langues