Dorel Home WM3921FP Assembly Manual

11

Thank you for purchasing from DHP!

Date of Purchase

G.Y. - 2023/07/29

WM3921E2 (Mocha), WM3921W-DC (White),

WM3921G-DC (Gray), WM3921B-DC (Black),

WM3921SG (Sage Green), WM3921FP (Fancy Pine)

Bunk Bed

Twin / Twin

Lot Number (TAKEN FROM CARTON)

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY

INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

B34WM392100-100063

Weight Limit : 165 Lb / 75 Kg per level

If parts are missing or damaged, we will gladly ship your

replacement parts free of charge.

Visit www.dhpfurniture.com/eng/replacement-parts

or call Toll-Free 1-800-267-1739

You can also chat with us at www.dhpfurniture.com

Questions, concerns, missing parts?

CONTACT OUR CUSTOMER SERVICE

DEPARTMENT BEFORE RETURNING PRODUCT

TO THE RETAILER.

22

Limited 1 year Warranty

DHP warrants this product to be free from defects in material and workmanship

and agrees to remedy any such defect. This warranty covers one year from the

date of original purchase from authorized retailers. This is solely limited to the

repair or replacement of defective parts and assembly labor is not included.

This warranty does not apply to any product which has been improperly

assembled, subjected to misuse or abuse or which has been altered or repaired

in any way.The warranty does not cover wearing, tearing, fading or splitting of the

fabric (where applicable). Liability for consequential damages is excluded to the

extent exclusion is permitted by law. This warranty gives you specific legal rights

and you may also have other rights which vary from state to state or province to

province.

To obtain warranty service, purchaser must present original bill of sale.

Components repaired or replaced are warranted through the remainder of the

original warranty period only. The defective components will be repaired or

replaced without charge, subject to the terms and conditions described above.

The terms and conditions of the limited warranty are subject to change without

notice. For the latest warranty policy, please visit www.dhpfurniture.com.

●Work in a spacious area and near where the unit will be used, preferably on a

carpet, or use a piece of the cardboard packaging to protect your floor and

product.

●Make sure all parts are included. Most parts are labeled or stamped on the raw

edge.

●Read each step carefully. It is very important that each step of the instructions is

performed in the correct order. If these steps are not followed in sequence,

assembly difficulties will occur.

●This product may contain small components. Please ensure that they are kept

away from small children.

●This product is designed for home use and is not intended for commercial use.

Contact Us!

For help with assembly, identifying parts, product information or to order parts,

please contact us: This product is shipped in

1 carton

www.dhpfurniture.com

Do NOT use

powertools

Phillips head screwdriver

needed (not included)

1 hour

Read Before Beginning Assembly

cs@dhpfurniture.com

1-800-267-1739

DHP Consumer Services

12345 Albert Hudon, Suite 100,

Montreal, Quebec H1G 3L1

33

●STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are not designed for use with the bed;

for example, but not limited to, hooks, belts and jump ropes.

WARNINGS - Bunk Bed: Twin / Twin

●Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove warning label from bed.

●The mattress platform is designed to support a mattress without the need for a posture board or box spring.

●Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls.

●USE ONLY A COIL SPRING MATTRESS ON THE UPPER BUNK. FAILURE TO DO SO CAN RESULT IN INJURY.

●Use only mattresses which are 74"-75" long and 37 1/2" - 38 1/2" wide on upper and lower bed. Ensure thickness of mattress does not exceed

6"(152mm). Surface of mattress must be at least 5"(127mm) below the upper edge of guardrails.

●Do not allow children under 6years of age to use the upper bunk.

●Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to the wall, the guardrail that runs the full length

of the bed should be placed against the wall to prevent entrapment between the bed and wall (applicable for bunk beds with full length

guardrails on one side).

●Periodically check and ensure that the guardrail, ladder and other components are in their proper position, free from damage, and that all

connectors are tight.

●Do not allow horseplay on or under the bed and prohibit jumping on the bed.

●Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.

●Use of a night light may provide added safety precaution for a child using the upper bunk.

●The use of water or sleep flotation mattresses is prohibited.

●Always use the ladder for entering and leaving the upper bunk.

●Prohibit more than one person on upper bunk.

●Keep these instructions for future reference.

44

PARTS

A

B

L

T

N

D

E

G

F

R

M

C

Q

I

O

P

S

K

J

H

55

PARTS LIST

TOP POST

1 PC

BOTTOM POST

2 PCS

BOTTOM POST

2 PCS

HEADBOARD TOP CROSS

4 PCS

HEADBOARD BOTTOM CROSS

4 PCS TOP SIDE RAIL (WITH 3 HOLES)

1 PC

A

HGF

D

C

B

E

66

PARTS LIST

BOTTOM SIDE RAIL (WITH 2 HOLES)

1 PC

TOP SIDE RAIL (WITH 1 HOLES)

1PC

BOTTOM SIDE RAIL (WITH NO HOLES)

1 PC

SLAT

12 PCS

LONG GUARDRAIL

2 PCS

SHORT GUARDRAIL

2 PCS

LONG LADDER END

1 PC

SHORT LADDER END

1 PC

LADDER STEP

4 PCS

GUARDRAIL LEG

2 PCS

HEADBOARD CENTER CROSS

4 PCS

SLAT

4 PCS

I

M

Q R S T

PO

L

K

N

J

77

Each part has a unique part number. Please

reference the appropriate part number when

contacting customer service for replacement parts.

Before throwing any packaging, please

verify all contents and make sure you

have received all the parts listed above!

PART UNMBERS

PART

LABELS

WM3921E2

(Mocha) WM3921W-DC

(White)

WM3921G-DC

(Gray)

WM3921B-DC

(Black)

WM3921SG

(Sage Green)

WM3921FP

(Fancy Pine)

A WM3921E2-A WM3921W-DC-A WM3921G-DC-A WM3921B-DC-A T1028820 T1031600

B WM3921E2-B WM3921W-DC-B WM3921G-DC-B WM3921B-DC-B T1028830 T1031610

C WM3921E2-C WM3921W-DC-C WM3921G-DC-C WM3921B-DC-C T1028840 T1031620

D WM3921E2-D WM3921W-DC-D WM3921G-DC-D WM3921B-DC-D T1028850 T1031630

E WM3921E2-E WM3921W-DC-E WM3921G-DC-E WM3921B-DC-E T1028860 T1031640

F WM3921E2-F WM3921W-DC-F WM3921G-DC-F WM3921B-DC-F T1028870 T1031650

G WM3921E2-G WM3921W-DC-G WM3921G-DC-G WM3921B-DC-G T1028880 T1031660

H WM3921E2-H WM3921W-DC-H WM3921G-DC-H WM3921B-DC-H T1028890 T1031670

I WM3921E2-I WM3921W-DC-I WM3921G-DC-I WM3921B-DC-I T1028900 T1031680

J WM3921E2-J WM3921W-DC-J WM3921G-DC-J WM3921B-DC-J T1028910 T1031690

K WM3921E2-K WM3921W-DC-K WM3921G-DC-K WM3921B-DC-K T1028920 T1031700

L WM3921E2-L WM3921W-DC-L WM3921G-DC-L WM3921B-DC-L T1028930 T1031710

M WM3921E2-M WM3921W-DC-M WM3921G-DC-M WM3921B-DC-M T1028940 T1031720

N WM3921E2-N WM3921W-DC-N WM3921G-DC-N WM3921B-DC-N T1028950 T1031730

O WM3921E2-O WM3921W-DC-O WM3921G-DC-O WM3921B-DC-O T1028960 T1031740

P WM3921E2-P WM3921W-DC-P WM3921G-DC-P WM3921B-DC-P T1028970 T1031750

Q WM3921E2-Q WM3921W-DC-Q WM3921G-DC-Q WM3921B-DC-Q T1028980 T1031760

R WM3921E2-R WM3921W-DC-R WM3921G-DC-R WM3921B-DC-R T1028990 T1031770

S WM3921E2-S WM3921W-DC-S WM3921G-DC-S WM3921B-DC-S T1029000 T1031780

T WM3921E2-T WM3921W-DC-T WM3921G-DC-T WM3921B-DC-T T1029010 T1031790

88

HARDWARE LIST

Ø 1/4" x 100mm Ø 6.5mm x 48mm Ø 6.5mm x 100mm

JOINT CONNECTOR

(4mm hex head)

16 PCS

WOOD JOINT CONNECTOR

(4mm hex head)

14 PCS

WOOD JOINT CONNECTOR

(4mm hex head)

22 PCS

Ø 4mm x 35mm Ø 4mm x 30mm Ø 19mm x 95mm Ø 10mm x 50mm

FLAT HEAD SCREW

24 PCS

FLAT HEAD SCREW

6 PCS

WOOD DOWEL

4 PCS

WOOD DOWEL

62 PCS

Ø 11.8mm x 15mm

BARREL NUT

16 PCS

ALLEN KEY

1 PC

Hardware Pack

Please do not completely tighten all the hardware, until the entire assembly

is complete, unless otherwise indicated in the step-by-step instructions.

The screw(s), bolt(s) to be used at each step are

shown in actual size in the lower right corner of the page.

WM3921E2 (Mocha),

WM3921G-DC (Gray),

WM3921B-DC (Black)

HP#: TWM3921E2-00

WM3921W-DC (White),

WM3921SG (Sage Green) HP#: TWM3921N-DC-00

WM3921FP (Fancy Pine ) HP#: TWM3921FP-00

❶❷❸

❹❺❻❼

❽❾

99

Step 1

One of the top cross Fhas a label on it, Use it

during this step.

Insert wood dowels ❼into the ends of the top

cross Fx2, center cross Sx2 and bottom crosses

Gx2.

Attach posts A &B, A &Cto the crosses using

the wood joint connectors ❸as shown.

Use the Allen key ❾to tighten all

joint connectors.

X8X24

❸

❼

Warning label side face inward F

F

G

B

C

A

S

❾

❸

❼

1010

Step 2

Insert wood dowels ❼into the ends of top cross

Fx2 and center cross Sx2 and bottom crosses

Gx2.

Attach posts D & Eusing wood joint connectors

❸though crosses F, S& G.

X8

X24

❸

❼

F

G

E

D

S

❸

❼

D

❸

1111

Step 3

Insert barrel nuts ❽into side rails I & Kas

shown below.

Attach the rails I & Kto the posts D &E using

joint connectors ❶.

X8X8

❶

❽

D

E

D

E

I

K

❽

❶

1212

Step 4

Insert wood dowels ❼into each end of the

guardrails Mx2. Insert barrel nuts ❽into side

rails H & Jas shown below.

Attach the long guardrails M to posts B &Aand

secure using joint connectors ❸.

Attach the rails H & Jto the posts A, B &C

using joint connectors ❶.

X4X4 X8

X8

❸❶

❼

❽

Holesonthisside

C

A

B

H

J

M

❽

❶

❸

1313

Step 5

Place wood dowels ❻into the holes in the

posts Dx2 & Ex2.

Stack the top bunk onto the bottom bunk with

the help of another person.

X4

B

E

A

D

E

C

D

A❻

❻

1414

Step 6

Insert wood dowels ❼into the ends of the

ladder steps Qx4.

Attach ladder ends O &P to ladder steps Qwith

wood joint connectors ❷.

X8X8

P

Q

O

❷

❼

❷

❼

1515

Step 7

Attach the ladder to the side rails H & Iwith

wood joint connector ❷as shown.

X4

❷

I

H

❷

Q

P

1616

Step 8

Insert wood dowels ❼in the ends of short

guardrails N, Attach short guardrails N to top

post A with wood joint connectors ❸.

Attach the ladder to the short guardrails N with

wood joint connectors ❷as shown.

Attach the guardrail leg Rto M,N,J & Hwith flat

head wood screws ❺.

Use a Phillips head screwdriver (not included)

to install all screws.

X2X2

X2X6

❸

❷

❺

❼

N

A

M

R

H

J

O

❷

❺

❸

1717

Step 9

Insert slats with wood dowel Tx4 into the center

slots of the side rails I & K and H & Jof the bunk

as shown.

Attach slats without wood dowel Lx12 onto side

rails I & K and H & Jof the bunk with flat head

screws ❹.

X24

❹

K

L

I

T

1818

Bottombed

consistsofa

headboardof

onebed.

Aswellasthe

headboardofthe

secondbed.

Topbedconsists

ofafootboard

ofonebed.

Aswellasthe

footboardofthe

secondbed.

Thefirsttwinbed.

Thesecondtwinbed.

Separating the beds

Remove the ladder and all the guardrails.

With the help of another person, remove the top

bunk from the lower bunk.

Disassemble the side rails from all headboards

(top and lower bunks).

Re-assemble the headboards (with tall posts) and

footboards (with short posts) to side rails.

Note: Switching the headboards will allow the two

single beds to be identical (the headboards will

have taller posts and the footboards will have the

shorter posts).

1919

●Move your new furniture carefully, with two

people lifting and carrying the unit to its new

location.

●Your furniture can be disassembled and

reassembled to move.

●Dust this item regularly with a soft, lint- free

cloth to prevent soil build up. Do not soak or

wash in hot water. Wipe with a soft, damp cloth

if necessary. Do not use abrasives, cleansers or

polish.

●Check bolts and nuts periodically and tighten if

necessary.

Helpful Hints

CAUTION: This unit is intended for use only with the products and/or maximum

weights indicated. Use with other products and/or products heavier than the

maximum weights indicated may result in instability or cause possible injury.

That's it ! You've finished assembling your Bunk Beds!

Weight Limit: 165 Lb / 75 Kg per level

ESES

Fecha de compra Número de lote

ESTE INSTRUCTIVO CONTIENE INFORMACION IMPORTANTE DE

SEGURIDAD. POR FAVOR LEA Y GUARDE PARA SU REFERENCIA FUTURA.

DHP garantiza que este producto está libre de defectos de material y mano de obra y se

compromete a remediar cualquier defecto de este tipo. Esta garantía cubre 1 año a partir de la

fecha de compra original. Esta garantía es válida solamente con presentación de una prueba

de compra. Esto se limita a la reparación o reemplazo de componentes defectuosos del mueble

y no se incluye ningún trabajo de ensamblaje.

Esta garantía no se aplica a ningún producto que haya sido mal ensanblado, sujeto a mal uso o

abuso, o que haya sido alterado o reparado de cualquier manera. Cualquier uso, rotura o

pérdida de color de la tela no están incluidos en esta garantía (donde corresponda). Esta

garantía le da derechos legales específicos y usted puede también tener otros derechos que

varían de estado a estado o de provincia a provincial.

Para obtener el servicio de garantía, debe presentar la factura original de su compra. Los

componentes reparados o reemplazados están garantizados durante el periodo original de la

garantía. Las partes defectuosas serán reparadas o reemplazadas sin cargo extra y sujetas a

los términos y condiciones descritos anteriormente. Los términos y condiciones de la garantía

limitada están sujetos a cambios sin previo aviso. Para conocer la política de garantía más

reciente, visite www.dhpfurniture.com.

Información sobre la garantía

¡Gracias por tu compra DHP!

●Este producto está diseñado para uso doméstico y no para uso comercial.

●ADVERTENCIA PARA NIÑOS PEQUEÑOS - Este producto contiene

componentes pequeños. Por favor asegúrese de que las piezas estén fuera del

alcance de los niños.

●No utilice herramientas eléctricas para ensamblar su mueble. Este tipo de

herramientas pueden rasgar o dañar las partes.

Precauciones

Lea antes de comenzar a ensamblar

●Llame a nuestro número gratuito si necesita asistencia.

●Trabaje en un área espaciosa y cerca de donde su producto será utilizado,

preferiblemente sobre una alfombra o utilice el cartón del empaque para

proteger su piso y su producto.

●El número de personas recomendadas para el montaje de este producto

es: 1 (sin embargo, es recomendable contar con ayuda adicional).

●Tiempo estimado de ensamble es 1 hora.

●Asegúrese de que todas las partes están incluidas. La mayoría de las partes

están etiquetadas o selladas en los bordes.

●Lea cada paso cuidadosamente. Es muy importante que cada paso de las

instrucciones sea realizado en el orden correcto. Si estos pasos no se siguen

en secuencia, pueden ocurrir dificultades durante el ensamblado.

¡Contáctenos !

Para solicitar ayuda con el ensamblaje, identificación de partes, información del

producto o simplemente ordenar otras partes, diríjase a:

●Chatea con nosotros: www.dhpfurniture.com

●[email protected]

●1-800-267-1739

●DHP Servicio al Cliente

12345 Albert Hudon, Suite 100, Montreal, Quebec, Canada, H1G 3L1

Individual / Individual

Litera

Preguntas, inquietudes, partes que faltan? CONTACTE A

NUESTRO DEPARTAMENTO DE SERVICIO AL CLIENTE ANTES

DE DEVOLVER EL PRODUCTO A LA TIENDA.

Si le faltan piezas o las que se incluyen están dañadas, con mucho gusto le

enviaremos sus piezas de reemplazo sin cargo extra.

Visite www.dhpfurniture.com/spa/replacement-parts, llame gratis al

1-800-267-1739 o chatea con nosotros en www.dhpfurniture.com

WM3921E2 (Mocha), WM3921W-DC (Blanco),

WM3921G-DC (Gris), WM3921B-DC (Negro),

WM3921SG (Verde Salvia), WM3921FP (Pino de lujo)

La page charge ...

Dorel Home WM3921FP Assembly Manual

Dorel Home WM3921FP Assembly Manual

dans d''autres langues

Documents connexes

Autres documents