red lion DA 8DI Guide d'installation

Marque: red lion

Modèle: DA 8DI

Taper: Guide d'installation

Ce manuel convient également à

DA 8DI/8RO Module

Installation 8DI/RO - A

Drawing No. LP1119

Effective 02/2020

DA 8 Digital Input / 8 Relay Output Module

Installation Guide

FOR USE IN HAZARDOUS LOCATIONS:

Class I, Division 2, Groups A, B, C, and D

LISTED

IND.CONT. EQ.

E317425

MODULE PACKAGE CHECKLIST

This product package should contain the items listed below. If

any items are missing or damaged, contact Red Lion immediately.

- DIN Rail Mount DA 8DI/8RO Module

- Installation Guide

GENERAL DESCRIPTION

The DA 8DI/8RO module is designed for use with the DA70

controllers, that can support up to 10 I/O modules simultaneously.

This module features 8 Digital Inputs and 8 Relay Outputs that

can be used to monitor contact or sensor inputs and actuate

relays, solenoids, PLC inputs, etc.

The inputs accept standard DC inputs or contact closures, and

are configured for Sink/Source signals via software switches.

Additionally, each input has a switch selectable input filter that

can be used to prevent contact bounce. Each input may also be

software configured as a high-active or low-active input.

The module is available with relay outputs that are capable of

switching up to one amp each. For applications requiring large

loads to be controlled, several DIN rail mount relays are available.

The modules connect and communicate via proprietary

backplane to the DA host device. The DA host device, equipped

with serial ports as well as an Ethernet port(s), allows the system

to share data with PCs, PLCs, and SCADA systems.

Internal power management circuits allow the module to be

replaced while power is applied, which reduces downtime in the

event of a module failure. All configuration information is stored

locally within the module, as well as in the Host, so replacement

modules do not need to be configured.

DIMENSIONS In Inches (mm)

CONFIGURATION

The DA 8DI/8RO modules are configured with Windows

compatible Crimson

software. The software is an easy to use,

graphical interface which provides a means of configuration and

commissioning of new systems, as well as routine module

re-calibration.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that

appear in this document or on equipment must be observed to

ensure personal safety and to prevent damage to either the

device or equipment connected to it.

Do not use these products to replace proper safety interlocking.

No software-based device (or any other solid-state device) should

ever be designed to be responsible for the maintenance of

personnel safety or consequential equipment not equipped with

safeguards. Red Lion disclaims any responsibility for damages,

either direct or consequential, that result from the use of this

equipment in a manner not specified.

0.49

(12.51)

0.45 (11.50)

4.53 (114.97)

6.22

(157.91)

1.91

(48.51)

1.35

(34.32)

6.00

(152.40)

CAUTION: Risk of Danger

Read complete instructions prior to installation and

operation of the unit.

ATTENTION : Risque de danger

Lire les instructions complètes avant l’installation et

l’utilisation de l’appareil.

WARNING - EXPLOSION HAZARD - SUBSTITUTION

OF COMPONENTS MAY IMPAIR SUITABILITY FOR

CLASS I, DIVISION 2

AVERTISSEMENT - DANGER D’EXPLOSION - LE

REMPLACEMENT DE COMPOSANTS PEUT NUIRE À

L’APTITUDE À LA CLASSE I, DIVISION 2

This equipment is suitable for use in Class I, Division 2,

Groups A, B, C, D, or non-hazardous locations only.

Cet équipement est adapté à une utilisation dans des

endroits de classe I, Division 2, Groupes A, B, C, D, ou

dans des endroits non dangereux seulement.

z Adds I/O capability to the DA70

z Offers complete isolation; inputs, power and Controller

z Inputs independently software selectable for sink or source

signals, high or low active states, and high or low frequency

signals

z Ideal for data acquisition applications

z Configured using Crimson

software (version 3.1 or later)

Drawing No. LP1119 Effective 02 2020

WARNING - EXPLOSION HAZARD. NOT HOT

SWAPPABLE. DO NOT REMOVE OR REPLACE WHILE

CIRCUIT IS LIVE UNLESS THE AREA IS FREE OF

IGNITIBLE CONCENTRATIONS.

AVERTISSEMENT - RISQUE D’EXPLOSION. NON

ÉCHANGEABLE À CHAUD. NE PAS RETIRER OU

REMPLACER SOUS TENSION SAUF SI LA ZONE EST

EXEMPTE DE CONCENTRATIONS INFLAMMABLES.

SPECIFICATIONS

1. POWER REQUIREMENTS:

Power is supplied by the DA host controller. Modules may be

hot-swapped (replaced while powered up) in non-hazardous

locations only.

Max Power: 2.0 W

2. LEDs: One LED indicator for each I/O point and a status LED.

3. MEMORY: Non-volatile memory retains all programmable

parameters.

4. Digital Input: Software selectable for sink or source

Maximum voltage: +30 VDC, reverse polarity protected

Off Voltage: < 1.2 Volts

On Voltage: > 3.8 Volts

Input Impedance: Source Mode 10K ohms; Sink Mode 20K ohms

Input Frequency*:

Software Filter selection on: 50 Hz

Software Filter selection off: 300 Hz

* Actual usable frequency limited by communication to

external device.

5. Form A Relay Output:

Type: Normally Open

Current Ratings:

Per Relay: 0.5 Amps @ 30 VDC/125 VAC at 75 °C

1.0 Amps @ 30 VDC/125 VAC at 55 °C

Per Module: 4.0 Amps @ 30 VDC/125 VAC at 75 °C

8.0 Amps @ 30 VDC/125 VAC at 55 °C

Life Expectancy: 100,000 cycles at max. load rating.

(Decreasing load, increasing cycle time, and use of surge

suppression such as RC snubbers increases life expectancy.)

6. ISOLATION LEVEL: 500 Vrms @ 50/60 Hz for 1 minute

between the following:

Inputs

Outputs

Host Controller

7. COMMUNICATIONS: Provided by the DA70 Controller

8. ENVIRONMENTAL CONDITIONS:

Operating Temperature Range: -40 to 75 °C

Storage Temperature Range: -40 to 80 °C

Vibration to IEC 60068-2-6: Operational 5-500 Hz, 2 g

Shock to IEC 60068-2-27: Operational 15 g

Operating and Storage Humidity: 0 to 95% max. RH non-

condensing

Altitude: Up to 2000 meters

Installation Category II, Pollution Degree 2 as defined in IEC/

EN 60664-1.

9. CERTIFICATIONS AND COMPLIANCES:

CE Approved

EN 61326-1 Immunity to Industrial Locations

Emission CISPR 11 Class A

IEC/EN 61010-1

RoHS Compliant

UL Hazardous: File # E317425

Rugged IP30 enclosure

10. CONNECTIONS: Removable wire clamp screw terminal blocks

Wire Strip Length: 0.3" (7.5 mm)

Wire Gauge Capacity: 14 to 24 AWG (2.08 to 0.20 mm

)

copper wire only

Torque: 2 inch-lbs (0.23 N-m)

11. CONSTRUCTION: Polycarbonate enclosure with IP30

rating. For use only in an approved enclosure.

12. MOUNTING REQUIREMENTS: Mounts onto standard DIN

style top hat (T) profile mounting rails according to EN50022

– 35 x 7.5 mm and 35 x 15 mm.

13. WEIGHT: 14.0 oz (397 g)

EMC INSTALLATION GUIDELINES

Although Red Lion Controls products are designed with a high

degree of immunity to Electromagnetic Interference (EMI), proper

installation and wiring methods must be followed to ensure

compatibility in each application. The type of the electrical noise,

source or coupling method into a unit may be different for various

installations. Cable length, routing, and shield termination are

very important and can mean the difference between a successful

or troublesome installation. Listed are some EMI guidelines for a

successful installation in an industrial environment.

1. A unit should be mounted in a metal enclosure, which is

properly connected to protective earth.

2. Use shielded cables for all Signal and Control inputs. The

shield connection should be made as short as possible. The

connection point for the shield depends somewhat upon the

application. Listed below are the recommended methods of

connecting the shield, in order of their effectiveness.

a. Connect the shield to earth ground (protective earth) at one

end where the unit is mounted.

b. Connect the shield to earth ground at both ends of the cable,

usually when the noise source frequency is over 1 MHz.

3. Never run Signal or Control cables in the same conduit or

raceway with AC power lines, conductors, feeding motors,

solenoids, SCR controls, and heaters, etc. The cables should

be run through metal conduit that is properly grounded. This

is especially useful in applications where cable runs are long

and portable two-way radios are used in close proximity or if

the installation is near a commercial radio transmitter. Also,

Signal or Control cables within an enclosure should be routed

as far away as possible from contactors, control relays,

transformers, and other noisy components.

4. Long cable runs are more susceptible to EMI pickup than

short cable runs.

5. In extremely high EMI environments, the use of external EMI

suppression devices such as Ferrite Suppression Cores for

signal and control cables is effective. The following EMI

suppression devices (or equivalent) are recommended:

Fair-Rite part number 0443167251 (Red Lion #FCOR0000)

Line Filters for input power cables:

Schaffner # FN2010-1/07 (Red Lion #LFIL0000)

6. To protect relay contacts that control inductive loads and to

minimize radiated and conducted noise (EMI), some type of

contact protection network is normally installed across the

load, the contacts or both. The most effective location is

across the load.

a. Using a snubber, which is a resistor-capacitor (RC) network or

metal oxide varistor (MOV) across an AC inductive load is

very effective at reducing EMI and increasing relay contact

life.

b. If a DC inductive load (such as a DC relay coil) is controlled

by a transistor switch, care must be taken not to exceed the

breakdown voltage of the transistor when the load is

Effective 02 2020 Drawing No. LP1119

switched. One of the most effective ways is to place a

diode across the inductive load. Most Red Lion products

with solid state outputs have internal zener diode

protection. However external diode protection at the load is

always a good design practice to limit EMI. Although the

use of a snubber or varistor could be used.

Red Lion part numbers: Snubber: SNUB0000

Varistor: ILS11500 or ILS23000

7. Care should be taken when connecting input and output

devices to the instrument. When a separate input and output

common is provided, they should not be mixed. Therefore a

sensor common should NOT be connected to an output

common. This would cause EMI on the sensitive input

common, which could affect the instrument’s operation.

Visit https://www.redlion.net/emi for more information on EMI

guidelines, Safety and CE issues as they relate to Red Lion

products.

HARDWARE INSTALLATION

Removing Module From Cradle

To remove the module from the cradle, push in the module

release button at the top of the cradle and pull the module out of

the cradle.

MODULE

CRADLE

Attaching the Module/Cradle to the DIN Rail

The DIN rail should be mounted

horizontally so that the unit’s

ventilation holes are vertical in

relation to installation orientation.

A minimum clearance of 1 inch

(25.4 mm) should be maintained

above and below the unit to

ensure proper thermal regulation.

For hazardous location

installation, the unit shall be

installed inside a UL Listed

Industrial Control Panel or similar

type of enclosure that can only

be opened with the use of a tool.

The cradle can be installed on

the DIN rail with or without the

module attached. Ensure the DIN rail lock latch is in the outward

most position (unlocked). Hook the top back of the cradle DIN rail

clip over the DIN rail. Press the cradle until flush with the rail and

push the DIN rail lock latch to the latched (in) position.

Installing Module into Cradle

Push module into cradle until you hear an audible click

indicating it is properly latched.

MODULE CRADLE

DIN

rail

MODULE HOT SWAPPING

If the area is known to be non-hazardous (free of ignitable

concentrations), then a module can be removed and/or installed

into a cradle attached to the controller while power is applied.

However, it is NOT recommended to connect to or remove from

the controller, a module/cradle pair or group of modules/cradles,

while power is applied. The power should be turned off anytime

a cradle or group of cradles (with or without modules) is plugged

into or removed from the controller.

WIRING

All power, input and output (I/O) wiring must be in accordance

with Class I, Division 2 wiring methods and in accordance with

the authority having jurisdiction.

All conductors should meet voltage and current ratings for each

terminal. When wiring the module, use the numbers on the label

to identify the position number with the proper function. Strip

the wire, leaving approximately 0.3" (7.5 mm) of bare wire

exposed. Insert the wire into the terminal, and tighten.

DIN RAIL LOCK LATCH

Unlock Lock

Terminals 17 to 24

Terminals 25 to 32

Terminals 9 to 16

Terminals 1 to 8

IN3+

IN2+

COM IN

IN1+

COM IN

IN4+

IN8+

COM IN

IN5+

COM IN

IN7+

IN6+

COM IN

OUT 4

COM 3

OUT 1

COM 2

OUT 3

OUT 2

COM 1

COM 4

COM 8

COM 5

OUT 6

OUT 7

COM 6

OUT 5

COM 7

OUT 8

OUTPUTINPUT

CAUTION: Only UL listed wiring with temperature

ratings greater than 90 °C permitted for Class I, Division

2 installations.

ATTENTION: Seul le câblage homologué UL avec des

températures nominales supérieures à 90°C est autorisé

pour les installations de classe I, Division 2.

Drawing No. LP1119 Effective 02 2020

I/O Wiring

The DA 8DI/8RO offers 8 discrete

inputs and 8 Form A relay outputs. The

discrete inputs and outputs operate on

the same voltage that powers the unit.

Pluggable screw block terminals are

provided for the I/O wiring connections.

Refer to the diagrams below on how to

make your I/O connections.

OUT 4

COM 3

OUT 1

COM 2

OUT 3

OUT 2

COM 1

COM 4

OUT

Load

Relay Output Connection

IN3+

IN2+

COM IN

IN1+

COM IN

IN4+

COM IN

INPUT

Sourcing Input Connections

STATUS LED

LED

COLOR(S)

LED STATE MEANING

Blue 3 quick flashes Module is booting.

Green Solid Module is configured and running.

Green/Off Flashing Module is running but is not

configured.

Green/

Purple

Flashing Module is performing calibration.

Red/Green Flashing Module is running but

communication with the controller

is inactive. If status persists, contact

technical support.

Red/Off Flashing An internal error has occurred. If

status persists, contact technical

support.

Yellow/Off Flashing Module position is unassigned. If

status persists, contact technical

support.

Off Solid Module application is not running or

the module is not powered. If status

persists, contact technical support.

FIRMWARE UPGRADE

The module’s firmware is stored in flash memory so that

software/ hardware conflicts are avoided, and so features can be

added in the future.

During a download, Crimson compares its own library of

firmware files with those stored in the module. If they do not

match, Crimson will download the necessary firmware.

RED LION CONTROLS TECHNICAL SUPPORT

If for any reason you have trouble operating, connecting, or

simply have questions concerning your new DA Module, contact

Red Lion’s technical support.

Support: support.redlion.net

Website: www.redlion.net

Inside US: +1 (877) 432-9908

Outside US: +1 (717) 767-6511

ORDERING INFORMATION

DESCRIPTION PART NUMBER

DA 8 Channel DI/ 8 Channel RO Module DA M00I0 DI0R0 0000

Spaces in listed part numbers are shown to improve readability,

do not include when searching for or ordering these parts.

and the Red Lion logo are trademarks of Red Lion Controls,

Inc. All other company and product names are trademarks of

their respective owners.

LIMITED WARRANTY

(a) Red Lion Controls Inc. (the “Company”) warrants that all

Products shall be free from defects in material and workmanship

under normal use for the period of me provided in “Statement

of Warranty Periods” (available at www.redlion.net) current at

the me of shipment of the Products (the “Warranty Period”).

EXCEPT FOR THE ABOVE-STATED WARRANTY, COMPANY

MAKES NO WARRANTY WHATSOEVER WITH RESPECT

TO THE PRODUCTS, INCLUDING ANY (A) WARRANTY OF

MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE; OR (C) WARRANTY AGAINST

INFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS OF

A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW,

COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE

OF TRADE OR OTHERWISE. Customer shall be responsible for

determining that a Product is suitable for Customer’s use and that

such use complies with any applicable local, state or federal law.

(b) The Company shall not be liable for a breach of the warranty

set forth in paragraph (a) if (i) the defect is a result of Customer’s

failure to store, install, commission or maintain the Product

according to specicaons; (ii) Customer alters or repairs such

Product without the prior wrien consent of Company.

during the Warranty Period, Company shall, in its sole discreon,

either (i) repair or replace the Product; or (ii) credit or refund the

price of Product provided that, if Company so requests, Customer

shall, at Company’s expense, return such Product to Company.

(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL

BE THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY AND

COMPANY’S ENTIRE LIABILITY FOR ANY BREACH OF THE

LIMITED WARRANTY SET FORTH IN PARAGRAPH (a).

red lion DA 8DI Guide d'installation

Marque: red lion

Modèle: DA 8DI

Taper: Guide d'installation

Ce manuel convient également à

DA 8DI/8RO Module

Télécharger le PDF

rapport

dans d''autres langues

English: red lion DA 8DI Installation guide

Documents connexes

Autres documents

Atos CR17 Le manuel du propriétaire