GE GE30S10BAM Le manuel du propriétaire

Marque: GE

Modèle: GE30S10BAM

Catégorie: Chauffe-eau

Taper: Le manuel du propriétaire

Write the model and serial

numbers here:

Model # _________________

Serial # _________________

You can find them on the rating

label on the front side of your

water heater.

GE is a trademark of the General Electric Company. Manufactured under trademark license.

OWNER’S MANUAL

WATER HEATERS

Electric Residential

49-50336 Rev. 1 06-20 GEA

GE Branded Thermostat Control

Models with Top or Side Water

Connections

SAFETY INFORMATION .........3

OPERATING INSTRUCTIONS ....6

CARE AND CLEANING ...........9

INSTALLATION

INSTRUCTIONS ..................13

TROUBLESHOOTING TIPS ......14

REPLACEMENT PARTS .........15

WIRING DIAGRAM ...............16

LIMITED WARRANTY ...........17

CONSUMER SUPPORT ..........18

ESPAÑOL

Para consultar una version en

español de este manual de

instrucciones, visite nuestro sitio de

internet GEAppliances.com.

FRANÇAIS

Pour une version français de

ce manuel d’utilisation, veuillez

visiter notre site web à l’adresse

GEAppliances.com.

See http://info.nsf.org/Certified/Lead_

Content/ for specific model listing

2 49-50336 Rev. 1

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-50336 Rev. 1 3

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY INFORMATION

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric

shock, or to prevent property damage, personal injury, or loss of life.

Be sure to read and understand the entire Owner’ s Manual before attempting to install or operate this water

heater. It may save you time and cost. Pay particular attention to the Safety Instructions. Failure to follow these

warnings could result in serious bodily injury or death. Should you have problems understanding the instructions

in this manual, or have any questions, STOP and get help from a qualified service technician or the local electric

utility.

CAUTION

Risk of Fire - Hydrogen gas can be produced in a hot water system served by this water heater that has

not been used for a long period of time (generally two weeks or more). HYDROGEN GAS IS EXTREMELY

FLAMMABLE!! To dissipate such gas and to reduce risk of injury, it is recommended that the hot water faucet be

opened for several minutes at the kitchen sink before using any electrical appliance connected to the hot water

system. If hydrogen is present, there will be an unusual sound such as air escaping through the pipe as the water

begins to flow. Do not smoke or use an open flame near the faucet at the time it is open.

WARNING

Risk of Fire - DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance. Keep rags and other combustibles away.

FOR INSTALLATIONS IN THE STATE OF CALIFORNIA

California Law requires that residential water heaters must be braced, anchored or strapped to resist falling

or horizontal displacement due to earthquake motions. For residential water heaters up to 52 gallon (236.4 L)

capacity, a brochure with generic earthquake bracing instructions can be obtained from: Office of the State

Architect, 400 P Street, Sacramento, CA 95814 or you may call 916.324.5315 or ask a water heater dealer.

Applicable local codes shall always govern installation. For residential water heaters of a capacity greater than

52 gallons (236.4 L) consult the local building jurisdiction for acceptable bracing procedures.

WARNING

If the water heater has been subjected to flood, fire, or physical damage, turn off power and water to the

water heater.

Do not operate the water heater again until it has been thoroughly checked by qualified service personnel.

Safety Precautions

A. Do turn off power to water heater if it has been subjected to overheating, fire, flood or physical damage.

B. Do Not turn on water heater unless it is filled with water.

C. Do Not turn on water heater if cold water supply shut-off valve is closed.

NOTE: Flammable vapors may be drawn by air currents from surrounding areas to the water heater.

D. If there is any difficulty in understanding or following the Operating Instructions or the Care and Cleaning

section, it is recommended that a qualified person or serviceman perform the work.

4 49-50336 Rev. 1

SAFETY INFORMATION

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

Time/Temperature Relationship in Scalds

Temperature Time to Produce a Serious Burn

120°F (49°C) More than 5 minutes

125°F (52°C) 1-1/2 to 2 minutes

130°F (54°C) About 30 seconds

135°F (57°C) About 10 seconds

140°F (60°C) Less than 5 seconds

145°F (63°C) Less than 3 seconds

150°F (66°C) About 1-1/2 seconds

155°F (68°C) About 1 second

Table courtesy of Shriners Burn Institute

Water temperature over 125°F can

cause severe burns instantly or

death from scalds.

Temperature control settings

usually approximate tap water

temperature. However, factors

could cause water temperature

to reach 160°F regardless of the

control settings.

Children, disabled and elderly

are at highest risk of being scalded.

See instruction manual before

setting temperature at water

heater.

Feel water before bathing or

showering.

Temperature limiting valves are

available; see manual.

The chart shown above may be used as a guide in determining

the proper water temperature for your home.

DANGER

There is a Hot Water SCALD Potential if the

water temperature thermostat is set too high. Households

with small children, disabled or elderly persons may require

a 120°F (49°C) or lower thermostat setting to prevent contact

with “HOT” water.

Thermostat has been set at the factory to 120°F (49°C) to

reduce the risk of scald injury. This is the recommended starting

temperature setting, but it can be adjusted to any temperature

between 90°F and 150°F (32°C and 66°C).

Water Temperature Setting

The temperature of the water in the water heater can be regulated

by setting the temperature dial of the adjustable surface mounted

thermostat(s) located behind the jacket access panel(s). Dual

element heaters have 2 thermostats.

The illustration shows the temperature

adjustment dial used for setting the

water temperature.

Refer to the Operating Instructions in

this manual for detailed instructions in

how to adjust the thermostat(s).

DANGER

Hotter water increases

the Potential for Hot Water SCALDS.

WATER TEMPERATURE ADJUSTMENT

Safety, energy conservation, and hot water capacity are factors

to be considered when selecting the water temperature setting

of the water heater. Water temperatures above 125°F can cause

severe burns or death from scalding. Be sure to read and follow the

warnings outlined on the label pictured to the left. This label is also

located on the water heater near the top of the tank.

90°F150°F

125°F

TURN OFF

POWER

BEFORE

SERVICING

Reset

button

Thermostat

dial pointer

Thermostat

protective

cover

49-50336 Rev. 1 5

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

SAFETY CONTROLS

The water heater is equipped with a combination

thermostat and high limit Energy-Cut-Off control (ECO)

that is located above the heating element in contact

with the tank surface. If for any reason the water

temperature becomes excessively high, the high limit

control (ECO) breaks the power circuit to the heating

element. Once the control opens, it must be reset

manually. Resetting of the high limit control should be

done by a qualified service technician.

CAUTION

The cause of the high temperature

condition must be investigated by a qualified

service technician and corrective action must be

taken before placing the water heater in service

again.

To reset the temperature-limiting control:

1. Turn off the power to the water heater.

2. Remove the jacket access panel(s) and insulation.

The thermostat protective cover should not be

removed.

3. Press the red RESET button.

4. Replace the insulation and jacket access panel(s)

before turning on the power to the water heater.

5. Ensure water heater is operating properly after

resetting the ECO.

READ AND SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

6 49-50336 Rev. 1

Operating Instructions

Water Heater Capacity and Increasing

Temperature Setpoint:

The water heater temperature setting strongly impacts

the amount of usable hot water available for showers

and baths.

• Safety regulations require a factory setting no

greater than 125°F (52°C) for all new water heaters.

Therefore, if your old water heater was set to a hotter

temperature than your new water heater with a factory

set setpoint of 120°F (49°C), the new water heater

may seem to provide lower capacity than your old

water heater. This can be corrected by increasing the

temperature setpoint.

• If more hot water capacity is desired, increasing the

temperature from 120°F to 135°F (49°C to 57°C)

will enable the same tank of hot water to last about

25% longer because less hot water is mixed in at the

shower or faucet.

• Increasing the water temperature setpoint may

improve the cleaning performance of dishwashers and

washing machines.

• The user can adjust the temperature setting to meet

their needs. Always read and understand the safety

instructions contained in the owner’s manual before

adjusting the temperature setpoint.

If adjustment is necessary...

1. Turn off the power to the water heater.

2. Remove the jacket access panel(s) and insulation

exposing the thermostat(s).

The thermostat protective cover(s) should not be

removed.

3. Using a small screwdriver, set the thermostat(s) dial

pointer(s) to the desired temperature. Adjust the upper

and lower thermostats to the same temperature to

maximize hot water availability.

4. Replace the insulation and jacket access panel(s).

Turn on the power to the water heater.

Mixing Valves

• Mixing valves for reducing point-of-use water

temperature by mixing hot and cold water in branch

water lines are commercially available. Contact a

licensed plumber or the local plumbing authority for

further information.

Extended Shutdown Periods

If the water heater is to remain idle for an extended

period of time, the power and water to the appliance

should be turned off and the water heater drained to

conserve energy and prevent a buildup of dangerous

hydrogen gas. This unit has no power button, power

can only be shut off at the circuit breaker or disconnect

switch.

The water heater and piping should be drained if they

might be subjected to freezing temperatures.

After a long shutdown period, the water heater’s

operation and controls should be checked by qualified

service personnel. Make certain the water heater is

completely filled again before placing it in operation.

NOTE: Refer to the Hydrogen Gas Caution in the

Operating Instructions (see page 3).

OPERATING INSTRUCTIONS

90°F150°F

125°F

TURN OFF

POWER

BEFORE

SERVICING

Reset

button

Thermostat

dial pointer

Thermostat

protective

cover

49-50336 Rev. 1 7

Routine Preventive Maintenance

DANGER

Risk of Scald - Before manually

operating the relief valve, make certain no one will

be exposed to the danger of coming in contact with

the hot water released by the valve. The water may

be hot enough to create a scald hazard. The water

should be released into a suitable drain to prevent

injury or property damage.

NOTE: If the temperature and pressure-relief valve

on the hot water heater discharges periodically, this

may be due to thermal expansion in a closed water

system. Contact the water supplier or your plumbing

contractor on how to correct this. Do not plug the

relief valve outlet.

Properly maintained, your water heater will provide years

of dependable trouble-free service. It is suggested that

the following annual preventive maintenance program be

established.

1. Inspect Temperature & Pressure Relief Valve.

2. Inspect heating elements, ECO, and wiring to each.

3. Drain and Flush the water heater tank.

4. Anode rod must be removed and inspected.

Temperature and Pressure-Relief Valve:

Once a year, it is recommended to lift and release the

lever handle on the temperature and pressure-relief

valve, located on the front-right side of the water heater,

to make certain the valve operates freely. Allow several

gallons to flush through the discharge line to an open

drain.

Heating Elements and ECO:

Once a year, it is recommended to inspect the heating

elements, ECO, and wiring to each. Inspection should

be completed by service personnel qualified in electrical

appliance repair.

Most electrical appliances, even when new, make some

sound when in operation. If the hissing or singing sound

level increases excessively, the electric heating element

may require cleaning. Contact a qualified installer or

plumber for inspection.

Draining and Flushing the Water Heater

CAUTION

Risk of Shock - Shut off power to

the water heater before draining water.

DANGER

Risk of Scald - Before manually

operating the relief valve, make certain no one will

be exposed to the hot water released by the valve.

The water drained from the tank may be hot enough

to present a scald hazard and should be directed to

a suitable drain to prevent injury or damage.

A water heater’s tank can act as a settling basin for

solids suspended in the water. It is therefore not

uncommon for hard water deposits to accumulate in the

bottom of the tank. To clean the tank of these deposits, it

is recommended to drain and flush the water heater tank

once a year. To drain the water heater, follow these

steps:

1. Turn off power to the unit. The electric heating

elements will become damaged if operated without

water.

2. Attach a garden hose to the drain valve located at the

bottom of the unit and direct that hose to a drain.

3. Turn off the cold water supply.

4. Admit air to the tank by opening a hot water faucet or

lifting the handle on the relief valve.

5. Open the drain valve.

Flushing the Tank:

1. Follow steps above to drain the water heater.

2. Once the water heater is empty, with the drain valve

open and garden hose attached to the drain valve,

turn on the cold water supply.

3. Allow several gallons to flush through the drain valve

and hose to an open drain.

4. Turn off the water supply and allow any water

remaining in the tank to drain.

5. Repeat steps 3 and 4 until water runs clear.

6. Close the drain valve and fill the tank before returning

power to the unit. The tank is full when water runs out

of a nearby open hot water faucet.

Flushing should be done with an empty tank to promote

additional removal of sediment.

NOTE: See page 11 for product schematic.

CARE AND CLEANING

Care and Cleaning

Exterior Surfaces

Hand wash with damp cloth, using only warm water. Wipe dry using a dry, clean cloth.

Use a flat blade screwdriver

to turn brass drain valve or an

adjustable open-end wrench to

turn black stem on plastic drain

valve.

Straight Brass

Drain Valve

8 49-50336 Rev. 1

CARE AND CLEANING

Anode Rod

Anode rods are designed and installed to protect and

extend the life of residential water storage tanks.

The anode rod must be removed from the water heater’s

tank and inspected annually, and replaced when more

than 6” (15.2 cm) of core wire is exposed at either end of

the rod.* NOTE: Artificially softened water will cause the

anode rod to consume more rapidly.

Due to shock hazard and to prevent accidental water

leaks, this inspection should be done by a qualified

servicer or plumber, and requires that the electric power

and cold water supply be turned off before servicing the

anode rod.

NOTICE: Do not remove the anode rod from the water

heater’s tank except for inspection and/or replacement,

as operation with the anode rod removed will shorten

the life of the glass-lined tank and will void warranty

coverage.

Some areas have water conditions that may cause

an odor to develop in the water heater. Special alloy

replacement rods are available to address the condition.

*NOTE: Failure to replace the anode rod when

consumed voids the warranty for the tank. Warranty

coverage for all other components remains intact,

and is unaffected by this maintenance requirement.

The replacement anode rod, and the inspection for

consumption are not covered by warranty.

Care and Cleaning

Routine Preventative Maintenance

49-50336 Rev. 1 9

CARE AND CLEANING

Anode Rod Maintenance and Service

Tools needed:

• Flat Head Screwdriver

• Socket/Torque Wrench

• 1

/16” Socket

• Pipe Joint Compound or Pipe Thread Sealant Tape

• Anode Rod, if needed

* See page 18 for part ordering instructions

To service the Anode Rod:

1. Disconnect power, shut off the water supply, drain the

water lines of the home. Drain one or two gallons from

the water heater through the lower drain valve.

2. Remove anode cap and foam insulation in hole with

flat head screwdriver to expose anode fitting as shown

in Illustration A.

3. Using a 1

/16” socket, unscrew the anode rod, then lift

out to inspect as shown in Illustration B.

4. Inspect and replace if necessary.

5. To install the anode rod, seal the threads with pipe

joint compound or pipe thread sealant tape, thread

into the port and using the torque wrench tighten to 50

± 5 ft-lbs of torque.

6. Turn water supply on, open a tap to remove any air

in plumbing system, inspect for leaks, then replace

anode cap and turn the power on.

CAUTION - IMPORTANT SAFETY NOTICE

This information is intended for use by individuals

possessing adequate background of electrical,

electronic and mechanical experience. Any attempt

to repair a major appliance may result in personal

injury and property damage. The manufacturer or

seller cannot be responsible for the interpretation

of this information, nor can it assume any liability in

connection with its use.

Illustration A

Illustration B

Replace Anode Rod if

more than 6” of core wire

is exposed.

10 49-50336 Rev. 1

Installation Instructions

INSTALLATION INSTRUCTIONS

The location chosen for the water heater must take

into consideration the following:

LOCAL INSTALLATION

REGULATIONS

This water heater must be installed in accordance

with these instructions, local codes, utility codes,

utility company requirements or, in the absence of

local codes, the latest edition of the National Electrical

Code. It is available from some local libraries or

can be purchased from the National Fire Prevention

Association, Batterymarch park, Quincy, MA 02169 as

booklet ANSI/NFPA 70.

POWER REQUIREMENTS

Check the markings on the rating plate of the water

heater to be certain the power supply corresponds

to the water heater requirements. NOTE: 208V

installations may experience lower performance.

LOCATION

The water heater and water lines should be protected

from freezing temperatures and high-corrosive

atmospheres. Do not install the water heater in

outdoor, unprotected areas.

Locate the water heater in a clean dry area as near as

practical to the area of greatest heated water demand.

Long uninsulated hot water lines can waste energy

and water. Unit must be installed in a level location.

If required, add shims under base of unit to level for

proper operation.

NOTE: This unit is designed for any common indoor

installation.

Servicing the water heater requires proper installation

such that front panels can be removed to permit

inspection and servicing. Reference installation

instructions found in this manual.

Moving the water heater or other appliances to provide

service to the water heater is not covered under

warranty.

CAUTION

Risk of Property Damage -

The water heater should not be located in an

area where leakage of the tank or connections

will result in damage to the area adjacent to it

or to lower floors of the structure. Where such

areas cannot be avoided, it is recommended

that a suitable catch pan, adequately drained, be

installed under the water heater.

LOCATION (Cont).

Required clearances:

There must be sufficient clearance between any

object and the top, rear and sides of the water

heater in the event service is needed. The controls

and drain at front of unit must have clear access

for operation and service. Installations that require

minimal clearance on the sides or rear of the water

heater for earthquake straps are also acceptable.

In these cases, additional clearance should be

provided on the opposite side of the unit to

allow for service access.

CATCH PAN INSTALLATION

(If required)

NOTE: Auxiliary catch pan MUST conform to local

codes. Catch Pan Kits are available from the store

where the water heater was purchased, a builder

store or any water heater distributor. The catch

pan should be 2” (5.1 cm) minimum larger than the

Water Heater base diameter. To prevent corrosion

and improve Drain Valve access it is recommended

that the water heater be placed on spacers inside

the catch pan.

Relief Valve

Drain Line

Catch Pan

Drain (piped to

suitable drain)

THERMAL EXPANSION

If a check valve is present on the inlet water line,

it will create a “closed system.” Heating water in

a closed system creates an increase in pressure

within the water system because the pressure is not

able to dissipate in the main supply line. Referred to

as “thermal expansion”, the rapid pressure increase

can cause the relief valve to operate (releasing

water) during each heating cycle, potentially

causing premature failure to the valve or even the

water heater. The suggested method of controlling

thermal expansion is to install an expansion tank in

the cold water line between the water heater and the

check valve as shown in the following illustrations.

Contact your installing contractor, water supplier, or

plumbing inspector for additional information.

49-50336 Rev. 1 11

Installation Instructions

INSTALLATION INSTRUCTIONS

WATER SUPPLY CONNECTIONS

Refer to the illustration below for recommended

installation. The HOT and COLD water connections

are clearly marked and are ¾” NPT on all models.

When connecting to the inlet/outlet ports, the use of ¾”

female NPT tapered thread fittings with use of thread

sealant is recommended. The installation of unions is

recommended on the hot and cold water connections

so that the water heater may be easily disconnected

for servicing if necessary. Piping should be routed to

allow anode rod removal.

NOTE: Install a shut-off valve in the cold water line

near the water heater. This will enable easier service

or maintenance of the unit later.

IMPORTANT: Do not apply heat to the HOT or

COLD water connections. If sweat connections

are used, sweat tubing to adapter before fitting

the adapter to the cold water connections on

heater. Any heat applied to the hot or cold water

connection will permanently damage the internal

plastic lining in these ports.

Install a vacuum relief valve and/or anti-siphon device

when required by local jurisdictions.

TYPICAL TOP CONNECT INSTALLATION

TYPICAL SIDE CONNECT INSTALLATION

(Otherwise same as Top Connect Installation)

HOT AND COLD PIPE INSULATION INSTALLATION

(if supplied with product)

For increased energy efficiency, some water heaters

have been supplied with two 24” sections of pipe

insulation.

Please install the insulation, according to the

illustrations above, that best meets your requirements.

Hot water

outlet to

fixtures

Shut-off valve

To cold

water

supply

Unions

Thermal

expansion

tank

(Install per

manuf.

instructions),

if required

Relief Valve

discharge within

6” of floor and no

closer than 2 times

the pipe diameter

per local code

Temperature &

Pressure Relief Valve

Conduit to Electrical

Junction Box (use only

copper conductors)

(Model appearance

may vary)

Drain valve

To cold

water

supply

Relief Valve

discharge

within 6” of

floor and no

closer than

2 times the

pipe diameter

per local

code

Conduit to Electrical Junction Box

(use only copper conductors)

(Model appearance may vary)

Drain valve

Hot water

outlet to

fixtures

Shut-off

valve

Temperature &

Pressure Relief

Valve

Typical vertical

piping arrangement

Typical horizontal

piping arrangement

Typical side piping

arrangement

Unions

12 49-50336 Rev. 1

Installation Instructions

INSTALLATION INSTRUCTIONS

TO FILL THE WATER HEATER

WARNING

Risk of Unit Damage - The

tank must be full of water before heater is turned

on. The water heater warranty does not cover

damage or failure resulting from operation with

an empty or partially empty tank.

Make certain the drain valve is completely closed.

Open the shut-off valve in the cold water supply line.

Open each hot water faucet slowly to allow the air to

vent from the water heater and piping.

A steady flow of water from the hot water faucet(s)

indicates a full water heater.

Condensation can form on the tank and fittings when

it is first filled with water. Condensation may also

occur with a heavy water draw and very cold inlet

water temperature.

This condition is not unusual and will disappear once

water is heated. If condition persists, examine fittings

for potential leaks and repair, as required.

NOTICE

Do not mis-wire electrical connections. 240VAC or

208VAC must be applied across L1 and L2 wires as

shown in ‘Water heater junction box’ illustration.

If a 4-conductor wire is supplied to the water heater,

cap the neutral, and connect the remaining wires as

illustrated.

RELIEF VALVE

WARNING

Risk of Unit Damage - The

pressure rating of the relief valve must not

exceed 150 PSI (1.03 MPa), the maximum working

pressure of the water heater as marked on the

rating plate.

A new combination temperature and pressure-relief

valve, complying with the Standard for Relief Valves

and Automatic Gas Shut-Off Devices for Hot Water

Supply Systems, ANSI Z21.22, is supplied and must

remain installed in the opening provided and marked

for this purpose on the water heater. No valve of any

type should be installed between the relief valve and

the tank. Local codes shall govern the installation of

relief valves.

The BTUH rating of the relief valve must not be less

than the input rating of the water heater as indicated

on the rating label located on the front of the heater

(1 watt=3.412 BTUH).

Connect the outlet of the relief valve to a suitable

open drain so that the discharge water cannot contact

live electrical parts or persons and to eliminate

potential water damage.

Piping used should be of a type approved for hot

water distribution. The discharge line must be no

smaller than the outlet of the valve and must pitch

downward from the valve to allow complete drainage

(by gravity) of the relief valve and discharge line. The

end of the discharge line should not be threaded or

concealed and should be protected from freezing.

No valve of any type, restriction or reducer coupling

should be installed in the discharge line.

CAUTION

To reduce the risk of excessive pressures and

temperatures in this water heater, install temperature

and pressure protective equipment required by local

codes and no less than a combination temperature

and pressure relief valve certified by a nationally

recognized testing laboratory that maintains periodic

inspection of production of listed equipment or

materials, as meeting the requirements for Relief

Valves and Automatic Gas Shutoff Devices for Hot

Water Supply Systems, ANSI Z21.22. This valve

must be marked with a maximum set pressure not

to exceed the marked maximum working pressure

of the water heater. Install the valve into an opening

provided and marked for this purpose in the water

heater, and orient it or provide tubing so that any

discharge from the valve exits only within 6 inches

above, or at any distance below, the structural floor,

and does not contact any live electrical part. The

discharge opening must not be blocked or reduced in

size under any circumstances.

Relief Valve

Insulation

49-50336 Rev. 1 13

Installation Instructions

INSTALLATION INSTRUCTIONS

ELECTRICAL CONNECTIONS

A separate branch circuit with copper conductors,

overcurrent protective device and suitable

disconnecting means must be provided by a qualified

electrician.

All wiring must conform to local codes or latest edition

of National Electrical Code ANSI/NFPA 70.

The water heater is completely wired to the junction

box at the top of the water heater. An opening for 1/2”

electrical fitting is provided for field wiring connections.

The voltage requirements and wattage load for the

water heater are specified on the rating label on the

front of the water heater.

The branch circuit wiring should include

either:

1. Metallic conduit or metallic sheathed cable approved

for use as a grounding conductor and installed with

fittings approved for the purpose.

2. Nonmetallic sheathed cable, metallic conduit or

metallic sheathed cable not approved for use

as a ground conductor shall include a separate

conductor for grounding. It should be attached to

the ground terminals of the water heater and the

electrical distribution box.

To connect power to the water heater:

1. Turn the power off.

2. Remove the screw/screws holding the junction box

top cover.

3. Install L1 to L1, L2 to L2 and ground wire onto the

fixed junction box cover, per illustration below.

4. Reconnect all screws attaching the junction box

covers.

WARNING

Risk of fire or electrical shock.

Ensure both junction box covers and ground

screws are securely fastened for proper

grounding.

NOTE: Install electric connections according to local

codes or latest edition of National Electrical Code

ANSI/NFPA 70.

WARNING

Proper ground connection is

essential. The presence of water in the piping

and water heater does not provide sufficient

conduction for a ground. Nonmetallic piping,

dielectric unions, flexible connectors, etc., can

cause the water heater to be electrically isolated.

Do not disconnect factory ground.

The manufacturer’s warranty does not cover any

damage or defect caused by installation, attachment

or use of any type of energy-saving or other

unapproved devices (other than those authorized by

the manufacturer) into, onto or in conjunction with the

water heater. The use of unauthorized energy-saving

devices may shorten the life of the water heater and

may endanger life and property.

The manufacturer disclaims any responsibility for

such loss or injury resulting from the use of such

unauthorized devices.

If local codes require external application of insulation

blanket kits, the manufacturer’s instructions included

with the kit must be carefully followed.

Application of any external insulation, blankets

or water pipe insulation to this water heater will

require careful attention to the following:

• Do not cover the temperature and pressure-relief

valve.

• Do not cover access panels to the heating elements.

• Do not cover the electrical junction box of the water

heater.

• Do not cover the operating or warning labels

attached to the water heater or attempt to relocate

them on the exterior of the insulation blanket.

NOTE: This guide recommends minimum branch

circuit sizing based on the National Electric Code.

Refer to wiring diagrams in this manual for field

wiring connections.

BRANCH CIRCUIT SIZING GUIDE

Total

Water

Heater

Wattage

Recommended Over-

Current Protection

(fuse or circuit breaker

amperage rating)

Copper Wire Size AWG

Basedon N.E.C. Table

310-16 (167°F/75°C.)

@240V 208-240V 208-240V

3,000 20 12

4,000 25 10

4,500 25 10

5,000 30 10

5,500 30 10

6,000 35 8

8,000 45 8

9,000 50 8

10,000 – –

11,000 – –

12,000 – –

Junction

Box Cover

Junction

Box Cover

House

Ground

(Green)

Water Heater Junction Box

(Black)

Factory Ground

(Red)

14 49-50336 Rev. 1

Troubleshooting

Before you call for service....

Save time and money! Review the chart below first and you may not need to call for service.

CAUTION

For your safety, DO NOT attempt repair of electrical wiring, controls, heating elements or other

safety devices. Refer repairs to qualified service personnel.

Problem Possible Causes What To do

OPERATION AND PERFORMANCE

Not enough or no hot

water

Water temperature may

be set too low

• See the Water Temperature Adjustment and Water Heater

Capacity sections. (Pages 4 and 6)

Cold water inlet

temperature may be

colder during the winter

months

• This is normal. The colder inlet water takes longer to heat.

• Consider increasing the set temperature as described in

the Water Temperature Adjustment section.

Leaking or open hot

water faucets

• Make sure all faucets are closed.

Long runs of exposed

pipe, or hot water piping

on outside wall

• Insulate piping.

Dip tube damaged • Contact your local installer, plumbing contractor, or

previously agreed upon service agency.

A fuse is blown, circuit

breaker tripped, or

electric service to your

home may be interrupted

• Replace fuse or reset circuit breaker.

• Contact the local electric utility.

Inadequate wiring • See the Installation Instructions.

Manual reset high limit

(ECO)

•

See the Safety Controls section, see page 5.

Water Connections to

unit reversed

• Correct piping connections.

Recirculating System

Interference (if installed)

• Check flow rate is not set too high.

• Insulate piping

Water is too hot Water temperature is set

too high

• See the Water Temperature Adjustment section.

Thermostat has failed

• Contact your local installer, plumbing contractor, or

previously agreed upon service agency.

OTHER

Rumbling noise Water conditions in your

home caused a buildup of

scale or mineral deposits on

the heating elements

• Remove and clean the heating elements. This should only be

done by a qualified service person or plumbing contractor.

Water dripping down the

outside of the heater

Hot/Cold water connections

or other parts have loosened

•

Tighten the loose connections. This should only be done by a

qualified service person or plumbing contractor.

Relief valve producing

popping sound or

draining

Pressure buildup caused

by thermal expansion to a

closed system

• This is an unacceptable condition and must be corrected. See

Thermal Expansion section on page 12. Do not plug the relief

valve outlet. Contact a plumbing contractor to correct this.

Hot water has a rotten

egg or sulfur smell

Certain water supplies with

high sulfate content will react

with the anode rod that is

present in all water heaters

for corrosion protection of

the tank

• The odor can be reduced or eliminated in most water heaters

by replacing the anode rod with less-active material rod. In

some cases, an added step of chlorinating the water heater and

all hot water lines may be necessary, contact your local water

professional or plumber for options and instructions.

Go to GEAppliances.com/waterheater for information on

purchasing this replacement anode rod. A qualified servicer or

plumber should do this replacement. Use of a non-GE Appliances

approved anode rod, or operating the water heater without a GE

Appliances approved anode rod will VOID the warranty.

• In certain cases, increasing the tank temperature to 140°F (60°C)

can reduce this odor issue. Reference the Water Temperature

Adjustment section of the Important Safety Information of this

manual for procedure and dangers of scalding water. Installation of

temperature limiting valves can be used to reduce risk of scalding.

TROUBLESHOOTING

49-50336 Rev. 1 15

Replacement Parts

REPLACEMENT PARTS

WATER INLET/OUTLET

PIPE & HEAT TRAP

DIP TUBE & GASKET

ANODE ROD

BADGE

UPPER THERMOSTAT

CLIP SPRING THERMOSTAT

HEATING ELEMENT & GASKET

LOWER THERMOSTAT

DRAIN VALVE

INSULATION LARGE

COVER ELEMENT LARGE

& SCREWS

COVER ELEMENT SMALL

& SCREWS

INSULATION SMALL

HEATING ELEMENT & GASKET

CLIP SPRING

BARRIER DIELECTRIC UPPER

BARRIER DIELECTRIC LOWER

JUNCTION BOX COVERS

& SCREWS

INSULATION

T&P VALVE

Appearance may vary by model.

For standard thermostat control models with double elements.

Instructions for Placing a Parts Order

To place orders using a Visa/MasterCard or Discover contact

GEApplianceparts.com.

All parts orders should include:

1. The model and serial number of the water heater from the

rating plate.

2. Specify voltage and wattage as marked on the rating plate.

3. Part description (as noted below) and number of parts

desired.

CAUTION

For your safety, DO NOT attempt repair

of electrical wiring, thermostat(s), heating elements or other

operating controls. Refer repairs to qualified service personnel.

16 49-50336 Rev. 1

Wiring Diagram

WIRING DIAGRAM

YELLOW

BLUE

BLACK

LOWER

HEATING

ELEMENT

UPPER

HEATING

ELEMENT

HIGH TEMP

LIMIT SWITCH

& UPPER

THERMOSTAT

LOWER

THERMOSTAT

JUNCTION BOX

BRANCH CIRCUIT

TO ELECTRICAL

DISTRIBUTION PANEL

GREEN

BLACK

YELLOW

RED

TO WRAPPER

TO CLIP SPING

THERMOSTAT

TO CLIP SPING

THERMOSTAT

JUNCTION BOX COVER (FIXED)

Factory Ground

House Ground

Wire

Connectors

GREEN

49-50336 Rev. 1 17

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

GE Appliances Electric Water Heater Limited Warranty

What Is Not Covered:

Ŷ 6HUYLFHWULSVWR\RXUKRPHWRWHDFK\RXKRZWRXVH

the product.

Ŷ ,PSURSHULQVWDOODWLRQGHOLYHU\RUPDLQWHQDQFH

Ŷ 5HSODFHPHQWSDUWVVKLSSLQJDQGKDQGOLQJDQGFRVWWR

remove defective part or tank after the first year limited

warranty are NOT covered.

Ŷ )DLOXUHRIWKHSURGXFWLILWLVDEXVHGPLVXVHGDOWHUHGRU

used for other than the intended purpose.

Ŷ 8VHRIWKLVSURGXFWZKHUHZDWHULVPLFURELRORJLFDOO\XQVDIH

or of unknown quality, without adequate disinfection before

or after the system.

Ŷ 5HSODFHPHQWRIKRXVHIXVHVRUUHVHWWLQJRIFLUFXLWEUHDNHUV

Ŷ 'DPDJHWRWKHSURGXFWFDXVHGE\DFFLGHQWOLJKWQLQJILUH

flood or acts of God.

Ŷ ,QFLGHQWDORUFRQVHTXHQWLDOGDPDJHFDXVHGE\SRVVLEOH

defects with this appliance, its installation or repair.

Ŷ 3URGXFWQRWDFFHVVLEOHWRSURYLGHUHTXLUHGVHUYLFH

in a safe

manner. Attic installation must have flooring and accessible

stairs.

Ŷ ,ISURGXFWUHPRYHGIURPRULJLQDOLQVWDOODWLRQORFDWLRQ

Ŷ ,ISURGXFWRURWKHUDSSOLDQFHPXVWEHPRYHGIRU

service access.

Ŷ 'DPDJHPDOIXQFWLRQRUIDLOXUHFDXVHGE\WKHXVHRIUHSDLU

service not approved by GE Appliances.

Ŷ 'DPDJHPDOIXQFWLRQRUIDLOXUHFDXVHGE\WKHXVHRI

unapproved parts or components.

Ŷ 'DPDJHPDOIXQFWLRQRUIDLOXUHFDXVHGE\RSHUDWLQJWKH

water heater with the anode rod removed.

Ŷ $QRGH5RGLQVSHFWLRQDQGUHSODFHPHQW

Ŷ 'DPDJHPDOIXQFWLRQRUIDLOXUHUHVXOWLQJIURPRSHUDWLQJWKH

water heater with an empty or partially empty tank.

Ŷ 'DPDJHPDOIXQFWLRQRUIDLOXUHFDXVHGE\VXEMHFWLQJWKH

tank to pressure greater than those shown on the rating

label.

Ŷ 'DPDJHPDOIXQFWLRQRUIDLOXUHFDXVHGE\RSHUDWLQJWKH

water heater with electrical voltage outside the voltage

range listed on the rating label.

Ŷ :DWHUKHDWHUIDLOXUHGXHWRWKHZDWHUKHDWHUEHLQJRSHUDWHG

in a corrosive atmosphere.

Ŷ ,IWKLVZDWHUKHDWHULVXVHGIRURWKHUWKDQUHVLGHQWLDOSULYDWH

family use, labor will not be covered under warranty, and

the parts warranty is reduced to 1 year from the date of

purchase.

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided

in this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

LIMITED WARRANTY

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within

the USA. If the product is located in an area where service by a GE Appliances Authorized Servicer is not available, you may

be responsible for a trip charge or you may be required to bring the product to an Authorized GE Appliances Service location for

service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives you

specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult

your local or state consumer affairs office or your state’s Attorney General.

For product purchased outside of the US, contact your dealer for Warranty and Service information.

Warrantor for Products Purchased in the United States:

GE Appliances, a Haier company

Louisville, KY 40225

All warranty service is provided by our Factory Service Centers, or an authorized Customer Care® technician. To schedule service

for your GE water heater call GE Water Heaters at 1-800-943-8186. Please have your serial number and your model number

available when calling for service. Servicing your appliance may require the use of the onboard data port for diagnostics. This gives

a GE Appliances factory service technician the ability to quickly diagnose any issues with your appliance and helps GE Appliances

improve its products by providing GE Appliances with information on your appliance. If you do not want your appliance data to be

sent to GE Appliances, please advise your technician not to submit the data to GE Appliances at the time of service

For The Period Of: We Will Replace:

One Year

From the date of the

original purchase

Any factory specified part of the water heater which fails due to a defect in materials or

workmanship. During this limited one-year warranty, we will also provide, free of charge, all

labor and related service to replace the defective part.

Second through

Eighth or Tenth Year

From the date of the

original purchase

Any part of the Water Heater which fails due to a defect in materials or workmanship. During

this limited second through the end of the warranty period, labor and related service to

replace the defective part are not included.

*Warranty is based on the 6th and 7th digit of model number located on rating plate (e.g.: GE50T08BAM has a part

warranty of 8 years).

18 49-50336 Rev. 1

Printed in ChinaPrinted in China

Consumer Support

CONSUMER SUPPORT

communication and prompt service under the terms of your warranty, should the need arise.

• Scan QR Code on product registration card, or on product.

NOTE: This is just an example of what a QR code represents.

• Or go to GEAppliances.com/register

• Or mail in your pre-printed registration card included in the packing material

Consumer Service

If you have a question or need assistance with your new water heater on adjustments, repairs, or routine

maintenance:

• Review the Troubleshooting Tips or Care and Cleaning sections of this Owner’s Manual.

• Contact your local installer, plumbing contractor, or call GE Appliances Service and Support at 1-800-943-8186.

NOTE: Your installer phone number may be located on the product label.

If you still have issues, contact the GEA Customer Support at GEAppliances.com/waterheater

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes.

(VISA, MasterCard and Discover cards are accepted). Order on-line today 24 hours every day.

In the US, go to GEApplianceparts.com

If you are ultimately not satisfied with the service you receive, contact us on our Website with all the details including

your phone number, or write to:

In the US: General Manager, Customer Relations |GE Appliances, Appliance Park |Louisville, KY 40225

GEAppliances.com/contact

Voir http://info.nsf.org/Certified/Lead_

Content/ for specific model listing

Inscrivez les numéros de modèle

et de série ici :

No de modèle ____________

No de série ______________

Vous trouverez ces numéros sur

l’étiquette apposée à l’avant de

votre chauffe-eau.

GE est une marque déposée de General Electric Company. Fabriqué sous licence de marque.

MANUEL

D’UTILISATION

CHAUFFES-EAU

Électrique à usage domestique

49-50336 Rev. 1 06-20 GEA

INFORMATION SUR LA

SÉCURITÉ .........................3

CONSIGNES D’UTILISATION ....6

ENTRETIEN ET NETTOYAGE ....9

INSTRUCTIONS

D’INSTALLATION ................13

CONSEILS DE DÉPANNAGE ....14

PIÈCES DE RECHANGE .........15

SCHÉMA DE CÂBLAGE .........16

GARANTIE LIMITÉE .............17

SOUTIEN

AU CONSOMMATEUR ...........18

Modèles de commande de

thermostat de marque GE avec

raccordements d’eau supérieurs

ou latéraux

2 49-50336 Rev. 1

NOUS VOUS REMERCIONS D’ACCUEILLIR GE APPLIANCES CHEZ VOUS

Que vous ayez grandi avec GE Appliances ou qu’il s’agisse de votre première acquisition, nous

sommes heureux de vous accueillir dans notre famille.

Nous sommes fiers du savoir-faire, de l’innovation et de l’esthétique qui composent chaque appareil

GE Appliances, et nous pensons que vous le serez aussi. Dans cette optique, nous vous rappelons

que l’enregistrement de votre électroménager vous assure la communication de renseignements

importants sur le produit et la garantie lorsque vous en avez besoin.

Enregistrez votre électroménager GE en ligne dès maintenant. Des sites Web et des numéros de

téléphone utiles figurent dans la section Soutien au consommateur de ce manuel d’utilisation. Vous

pouvez aussi poster la fiche de garantie pré-imprimée incluse dans l’emballage.

La page charge ...

GE GE30S10BAM Le manuel du propriétaire

Marque: GE

Modèle: GE30S10BAM

Catégorie: Chauffe-eau

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: GE GE30S10BAM Owner's manual
español: GE GE30S10BAM El manual del propietario

GE GE30S10BAM Le manuel du propriétaire

GE GE30S10BAM Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents