Saber Compact R67SC0917 Manuel utilisateur

Catégorie
Barbecues
Taper
Manuel utilisateur
Assembly instructions © 2016
© 2016 Saber Grills, LLC., Columbus, GA 31902
Printed in China
11/15/16 • 80026872
For patents see www.sabergrills.com/patents
If you have questions or need
assistance during assembly,
please call
1-888-94-SABER
1-888-947-2237
Serial Number
Date Purchased
Place serial
number label
here
IMPORTANT: Fill out the product
record information below.
VISIT SABERGRILLS.COM FOR
START-UP TIPS, RECIPES, SUPPORT,
AND PRODUCT REGISTRATION
FOR NATURAL GAS CONVERSION:
NG Conversion Kit Model A00AA5417 must be used. Sold separately.
PRODUCT GUIDE
MODEL R67SC0917
DANGER
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING
WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION: Indicates a potentially hazardous situation or
unsafe practice which, if not avoided, may result in minor
or moderate injury.
Safety Symbols
The symbols and boxes shown below explain what each
heading means. Read and follow all of the messages found
throughout the manual.
CAUTION:
Read and follow all safety statements, assembly
instructions, and use and care directions before attempting
to assemble and cook.
INSTALLER/ASSEMBLER:
Leave this manual with consumer.
CONSUMER:
Keep this manual for future reference.
WARNING:
Failure to follow all manufacturer’s instructions could result
in serious personal injury and/or property damage.
CAUTION:
Some parts may contain sharp edges – especially as noted
in the manual! Wear protective gloves if necessary.
TABLE OF CONTENTS
DANGER
WARNING
CAUTION
For residential use only. Do not use for commercial
cooking.
THIS GRILL IS FOR OUTDOOR USE ONLY.
2
If you smell gas:
· Shut off gas to appliance.
· Extinguish any open flame.
· Open lid.
· If odor continues, keep away from the appliance and
immediately call your gas supplier or your fire
department.
· Do not store or use gasoline or other flammable liquids
or vapors in the vicinity of this or any other appliance.
· An LP cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
WARNING
CALIFORNIA PROPOSITION 65
1. Combustion by-products produced when using
this product contain chemicals known to the State of
California to cause cancer, birth defects, and other
reproductive harm.
2. This product contains chemicals, including lead
and lead compounds, known to the State of
California to cause cancer, birth defects or other
reproductive harm.
Wash your hands after handling this product.
For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Grill Light Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-14
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Parts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20
3
CAUTION
Using pots larger than 15 quarts in capacity could
exceed weight limit of the side burner shelf, resulting in
failure of grill cart components.
USE AND CARE
WARNING
Do not attempt to repair or alter the
hose/valve/regulator for any “assumed” defect. Any
modication to this assembly will void your warranty
and create the risk of a gas leak and re. Use only
authorized replacement parts supplied by
manufacturer.
Installation Safety Precautions
Use grill, as purchased, only with LP (propane) gas and
the regulator/valve assembly supplied. A conversion kit
must be purchased for use with natural gas.
Grill installation must conform with local codes, or in their
absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2, or the Standard for Recreational
Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV
Series, Recreational Vehicle Code, as applicable.
All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or
National Electrical Code, ANSI / NFPA 70 or Canadian
Electrical Code, CSA C22.1. Keep any electrical cords
and/or fuel supply hoses away from any hot surfaces.
This grill is safety certied for use in the United States
and/or Canada only. Do not modify for use in any other
location. Modication will result in a safety hazard.
The pressure regulator and hose assembly supplied must
be used and replacements must be those specied by
appliance manufacturer.
NEVER store a spare cylinder under or near the
appliance or in an enclosed area.
Never ll a cylinder beyond 80% full.
An over lled or improperly stored cylinder is a hazard
due to possible gas release from the safety relief valve.
If you see, smell or hear gas escaping, immediately get
away from the LP cylinder/appliance and call your re
department.
This could cause an intense re with risk of property
damage, serious injury or death.
DANGER
LP Cylinder Valve
Retainer Strap
Safety
Cap
LP Cylinder Removal, Transport and Storage
· Turn OFF all control knobs and LP cylinder valve. Turn
coupling nut counterclockwise by hand only - do not use tools
to disconnect. Loosen cylinder screw beneath bottom shelf,
then lift LP cylinder up and out of cart. Install safety cap onto
LP cylinder valve. Always use cap and strap supplied with
valve. Failure to use safety cap as directed may result in
serious personal injury and/or property damage.
· A disconnected LP cylinder in
storage or being transported
must have a safety cap installed
(as shown). Do not store an LP
cylinder in enclosed spaces such as a
carport, garage, porch, covered patio or
other building. Never leave an LP cylinder
inside a vehicle which may become overheated
by the sun.
· Do not store an LP cylinder in an area where children play.
4
OPD Hand Wheel
LP cylinder in upright position for vapor withdrawal
LP Cylinder
The LP cylinder used with your grill must meet the following
requirements:
· Use LP cylinders only with these required measurements: 12”
(30.5cm) (diameter) x 18” (45.7cm) (tall) with 20 lb. (9kg) capacity
maximum.
· LP cylinders must be constructed and marked in accordance with
specications for LP cylinders of the U. S. Department of
Transportation (DOT) or for Canada, CAN/CSA-B339, cylinders,
spheres and tubes for transportation of dangerous goods.
Transport Canada (TC). See cylinder collar for marking.
· LP cylinder valve must have:
-Type 1 outlet compatible with
regulator or grill.
-Safety relief valve.
-UL listed Overll Protection
Device (OPD). This OPD safety
feature is identied by a unique triangular hand wheel. Use only
LP cylinders equipped with this type of valve.
· LP cylinder must be arranged for vapor withdrawal and include
collar to protect LP cylinder valve. Always keep LP cylinder in
upright position during use, transit or storage.
LP (Liqueed Petroleum Gas)
· LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten
cabbage) so that it can be smelled.
· LP gas is highly ammable and may ignite unexpectedly when
mixed with air.
LP Cylinder Filling
· Use only licensed and experienced dealers.
· LP dealer must purge new cylinder before lling.
· Dealer should NEVER fill LP cylinder more than 80% of LP
cylinder volume. Volume of propane in cylinder will vary by
temperature.
· A frosty regulator indicates gas overll. Immediately close LP
cylinder valve and call local LP gas dealer for assistance.
· Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.
· To remove gas from LP cylinder, contact an LP dealer or call a
local re department for assistance. Check the telephone
directory under “Gas Companies” for nearest certied LP
dealers.
LP Cylinder Exchange
· Many retailers that sell grills offer you the option of replacing your
empty LP cylinder through an exchange service. Use only those
reputable exchange companies that inspect, precision ll, test
and certify their cylinders. Exchange your cylinder only for an
OPD safety feature-equipped cylinder as described in the
“LP Cylinder” section of this manual.
· Always keep new and exchanged LP cylinders in upright position
during use, transit or storage.
· Leak test new and exchanged LP cylinders BEFORE
connecting to grill.
LP Cylinder Leak Test
For your safety
· Leak test must be repeated each time LP cylinder is exchanged
or relled.
· Do not smoke during leak test.
· Do not use an open ame to check for gas leaks.
· Grill must be leak tested outdoors in a well-ventilated area, away
from ignition sources such as gas red or electrical appliances.
During leak test, keep grill away from open ames or sparks.
· Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows in
gure below.
· Do not use household cleaning agents. Damage to gas train
components can result.
If “growing” bubbles appear do not use or move the
LP cylinder. Contact an LP gas supplier or your re
department!
WARNING
5
Safety Relief Valve
OPD Hand Wheel
c
k
w
o
l
i
s
C
e
f
f
O
Strap and Cap
Do not use a POL transport
plug (plastic part with external
threads)! It will defeat the
safety feature of the valve.
Type 1 outlet with
thread on outside
5. Hold regulator and insert nipple into LP
cylinder valve. Hand-tighten the
coupling nut, holding regulator in a
straight line with LP cylinder valve so
as not to cross-thread the connection.
Connecting Regulator to the LP Cylinder
1. LP cylinder must be properly secured onto grill. (Refer to
assembly section of your grill manual).
2. Turn all control knobs to the OFF position.
3. Turn LP cylinder OFF by turning hand wheel clockwise to a
Full Stop.
4. Remove the protective cap from LP cylinder valve. Always use
cap and strap supplied with valve.
Nipple has to be centered
into the LP cylinder valve.
Straight
Hold coupling nut and
regulator as shown for
proper connection to LP
cylinder valve.
Connecting Regulator to the LP Cylinder (Con’t.)
6. Turn the coupling nut clockwise and tighten to a Full Stop.
The regulator will seal on the back-check feature in the LP
cylinder valve, resulting in some resistance. An additional
one-half to three-quarters turn is required to complete the
connection. Tighten by hand only - do not use tools.
NOTE:
If you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!
WARNING
DANGER
Do not insert any tool or foreign object into the valve outlet
or safety relief valve. You may damage the valve and
cause a leak. Leaking propane may result in explosion,
fire, severe personal injury, or death.
· Outdoor gas appliance is not intended to be installed in
or on a boat.
· Outdoor gas appliance is not intended to be installed in
or on an RV.
· Never attempt to attach this grill to the self-contained LP
gas system of a camper trailer or motor home.
· Do not use grill until leak tested.
· If a leak is detected at any time, S TOP and call the fire
department.
· If you cannot stop a gas leak, i mmediately close LP
cylinder valve and call LP supplier or your fire
department!
6
5. If “growing” bubbles appear there is a leak. Close LP cylinder
valve immediately and retighten connections. If leaks cannot
be stopped do not try to repair. Call for replacement parts.
6. Always close LP cylinder valve after performing leak test by
turning hand wheel clockwise.
WARNING
Turn controls and gas source or tank OFF when not
in use.
NOTE:
Sideburner shelf fascia not shown for clarity.
Leak Testing Valves, Hoses and Regulator
1. Turn all control knobs to the OFF position.
2. Be sure regulator is tightly connected to LP cylinder.
3. Completely open LP cylinder valve by turning hand wheel
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct
before proceeding.
4. Brush soapy solution onto areas circled below, or other similar
ttings on your grill.
For Safe Use of Your Grill and to avoid serious injury:
· Do not let children operate or play near grill.
· Keep grill area clear and free from materials that burn.
· Do not block holes in sides or back of grill.
· Check burner ames regularly.
· Use grill only in well-ventilated space. N EVER use in
enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of any
kind.
· Do not use charcoal or ceramic briquets in a gas grill.
· Use grill at least 3 ft. from any wall or surface.
Maintain 10 ft. clearance to objects that can catch re or
sources of ignition such as pilot lights on water heaters,
live electrical appliances, etc.
Apartment Dwellers:
· Check with management to learn the requirements and
re codes for using an LP gas grill in your apartment
complex. If allowed, use outside on the ground oor
with a three (3) foot clearance from walls or rails. Do
not use on or under balconies.
· NEVER attempt to light burner with lid closed. A build-
up of non-ignited gas inside a closed grill is hazardous.
· Never operate grill with LP cylinder out of correct
position specied in assembly instructions.
· Always close LP cylinder valve and remove coupling nut
before moving LP cylinder from specied operation
position.
WARNING
NOTE: Sideburner shelf fascia not
shown for clarity.
7. Repeat steps 4 through 6 for second burner.
Viewing ports
Safety Tips
· Before opening LP cylinder valve, check the coupling nut for
tightness.
· When grill is not in use, turn off all control knobs and LP
cylinder valve.
· Never move grill while in operation or still hot.
· Use long handled barbecue utensils and oven mitts to avoid
burns and splatters.
· Maximum load for sideburner and side shelf is 10 lbs.
· The grease tray must be inserted into grill and emptied after
each use. Do not remove grease tray until grill has
completely cooled.
· Clean grill often, preferably after each cookout. If a bristle
brush is used to clean any of the grill cooking surfaces,
ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.
· If you notice grease or other hot material dripping from grill
onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.
· Keep ventilation openings in cylinder enclosure (grill cart)
free and clear of debris.
· Do not store objects or materials inside the grill cart
enclosure that would block the ow of combustion air to the
underside of either the control panel or the rebox bowl.
· The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
· If you have a grill problem see the Troubleshooting Section”.
· If the regulator frosts, turn off grill and LP cylinder valve
immediately. This indicates a problem with the cylinder and
it should not be used on any product. Return to supplier!
Main Burner Ignitor Lighting
Do not lean over grill while lighting.
1. Turn all control knobs to OFF.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. To ignite, push and turn burner control knob to
5. Push and hold ELECTRONIC IGNITION button until the burner
lights (use ame viewing ports to verify).
6. If ignition does NOT occur in 5 seconds, turn the burner controls
to OFF, wait 5 minutes, and repeat the lighting procedure.
7. Ignite remaining burners by repeating steps 4 through 6 for each
burner.
8. Once each burner has ignited, turn knobs to desired setting.
7
CAUTION
· Putting out grease res by closing the lid is not
possible. Grills are well ventilated for safety reasons.
· Do not use water on a grease re. Personal injury may
result. If a grease re develops, turn knobs and LP
cylinder off.
· Do not leave grill unattended while preheating or
burning off food residue on HI. If grill has not been
regularly cleaned, a grease re can occur that may
damage the product.
Main Burner Match-Lighting
Do not lean over grill while lighting.
1. Turn all control knobs to OFF.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. Place match into match holder (hanging from left side of cart).
Light match, place into lighting hole on left side of rebox.
5. Push in and turn far left control knob to position. Once
burner has ignited (use ame viewing ports to verify), turn
control knob to desired setting.
6. If ignition does NOT occur in 5 seconds, turn the control knob
to OFF, wait 5 minutes, and repeat the lighting procedure.
7. Light adjacent burners in sequence by pushing control knob
in and turning to position.
Sideburner Ignitor Lighting
Do not lean over grill while lighting.
1. Turn all control knobs to OFF.
2. Turn ON gas at LP cylinder.
3. Open sideburner lid during lighting.
4. To ignite push in and turn side burner control knob to .
5. Push and hold ELECTRONIC IGNITION button until the burner
lights.
6. If ignition does NOT occur in 5 seconds, turn the control knob
to OFF, wait 5 minutes, and repeat the lighting procedure.
If ignition does NOT occur in 5 seconds, turn the
control knobs OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to ow out of the
burner and could accidently ignite with risk of injury.
CAUTION
8 8
Burner Flame Check
· Remove cooking grates and emitters. Light burners, rotate control
knobs from HI to LO. You should see a smaller ame in LO
position than seen on HI. Perform burner ame check on side
burner, also. Always check ame prior to each use. If only low
ame is seen refer to “Sudden drop or low ame” in the
Troubleshooting Section.
Turning Grill OFF
· Turn all control knobs to OFF position. Turn LP cylinder OFF by
turning hand-wheel clockwise to a full stop.
Ignitor Check
· Turn Gas OFF at LP cylinder. Press and hold electronic ignition
button. “Click” should be heard and spark seen each time
between collector box or burner and electrode. See
“Troubleshooting” if no click or spark.
Valve Check
· IMPORTANT: Make sure gas is OFF at LP cylinder before
checking valves. Control knobs lock in OFF position. To check
valves, rst push in knobs and release, knobs should spring back.
If control knobs do not spring back, replace valve assembly before
using grill. Turn control knobs to LO position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
· Before each use, check to see if hoses are cut or worn. Replace
damaged hoses before using grill. Use only valve/hose/regulator
specied by manufacturer.
HI
LO
Sideburner Match-Lighting
Do not lean over grill while lighting.
1. Turn all control knobs to OFF.
2. Turn ON gas at LP cylinder.
3. Open lid during lighting.
4. Place lit match near inside
bottom opening of burner pan.
5. Push in and turn control
knob of the burner
to the position.
Ensure burner stays lit.
Quick Start Tips
Reversible sideburner grate:
· The dual function sideburner grate has a at surface on one side
for warming, boiling, or frying using pots and pans and it has a
curved surface on the other side for wok usage.
Preheating for different types of grilling:
· Sear - preheat with all burners set to HI for maximum cooking
grate temperatures
· Barbecue - preheat with all burners set to LO for a lower starting
grate temperature for grilling foods slower.
Quick Start Tips (con’t.)
Preheating for different types of grilling:
· Indirect grilling - preheat one burner only on the side opposite
where the food will be placed to allow the slowest and lowest
grilling for larger cuts of meat.
· Roasting - place the warming rack on the lower supports and
use burner(s) directly under the food on LO or indirectly for lower
temperature cooking. This will allow more heat to circulate
around the food during grilling.
Lowering the temperature of the cooking grate:
· Control knob - turn the control knob to the LO setting for the
lowest temperature setting.
· Control knob - for the lowest cooking grate temperatures the
food can be grilled indirectly with the burner under the food in the
OFF position and a single burner away from the food on LO.
· During grilling the grill can be cooled down faster by lifting the lid
while adjusting the control knobs to a lower setting.
Adding a smoked avor while grilling:
· Do not use wood chunks on a Saber grill cooking grate.
· Wood chips can be used by placing them between the cooking
grate bars. Soaking the wood chips for a minimum of 15
minutes prior to use will extend the smoking time.
· A smoker box (sold separately) can be used by lling it with
wood chips and placing it directly on the cooking grate
with the burner on the HI or LO setting.
General Grill Cleaning
· Do not mistake brown or black accumulation of grease and
smoke for paint. Apply a strong solution of detergent and
water or use a grill cleaner with scrub brush on insides of grill lid
and bottom. Rinse and allow to completely air dry.
Do not apply a caustic grill/oven cleaner to painted surfaces.
· Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
· Porcelain surfaces: Because of glass-like composition,
most residue can be wiped away with baking soda/water solution
or specially formulated cleaner. Use non-abrasive scouring
powder on stubborn stains.
· Painted surfaces: Wash with mild detergent or non-abrasive
cleaner and warm soapy water. Wipe dry with a soft non-
abrasive cloth.
· Stainless steel surfaces: To maintain your grill’s high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on
grease deposits may require the use of an abrasive plastic
cleaning pad. Use only in direction of brushed nish to avoid
damage. Do not use abrasive pad on areas with graphics.
6. Light adjacent burner by pushing
knob in and turning to the position.
Firebox
Carryover tube
Electrode
Firebox burner
bracket
Pry off electrode with a at
blade screwdriver
Retainer clip
9
Correct
burner-to-valve
engagement
Storing your grill
· Clean cooking grates.
· Store in dry place.
· When LP cylinder is connected to grill, store outdoors in a
well ventilated space and out of reach of children.
· Cover grill if stored outdoors. Choose from a cover offered
by the manufacturer.
· Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.
· When removing grill from storage, follow Cleaning the
Burner Assembly” instructions before starting grill.
CAUTION
CONTROL PANEL
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER TUBE
VALVE
SPIDER WEBS
BURNER
INSIDE BURNER
CONTROL PANEL
If you notice that your grill is getting hard to light or that the
ame isn’t as strong as it should be, take the time to check and
clean the burners.
In some areas of the country, spiders or small insects have been
known to create “ashback” problems. The spiders spin webs, build
nests and lay eggs in the grill’s burner tube(s) obstructing the ow of
gas to the burner. The backed-up gas can ignite in the burner
behind the control panel. This is known as a ashback and it can
damage your grill and even cause injury.
To prevent ashbacks and ensure good performance the burner
assembly should be removed from the grill and cleaned before use
whenever the grill has been idle for an extended period.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1. Turn gas to OFF at control knobs and gas source.
2. Remove cooking grates and emitters.
3. Remove retaining clips and carryover tubes from rear of
burners.
4. Using a flat blade screwdriver pry off the electrode from each
burner. Electrode should remain in burner box connected to
ignition wire.
5. Carefully lift each burner up and away from valve openings.
6. We suggest three ways to clean the burner tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well) into
a small hook. Run the hook through each burner tube
several times.
(B) Use a narrow bottle brush with a exible handle (do not use
a brass brush), run the brush through each burner tube
several times.
(C) Wear eye protection: Use an air hose to force air into the
burner tube and out the burner ports. Check each port to
make sure air comes out each hole.
7. Wire brush entire outer surface of burner to remove food
residue and dirt.
8. Clean any blocked ports with a stiff wire such as an open paper
clip.
9. Check burner for damage, due to normal wear and corrosion
some holes may become enlarged. If any large cracks or holes
are found replace burner.
10.Re-attach electrode to burner. Ensure ignition wire is
connected.
11.Carefully replace burners. VERY IMPORTANT: Burner tubes
must re-engage valve opening.
12.Re-attach burners to brackets inside burner box.
13.Reposition carryover tubes and re-attach to burners.
14.Replace emitters and cooking grates.
Cooking surfaces: If a bristle brush is used to clean any of the
grill cooking surfaces, ensure no loose bristles remain on cooking
surfaces prior to grilling. It is not recommended to clean cooking
surfaces while grill is hot.
VALVE
SPIDER WEBS
BURNER
INSIDE BURNER
CONTROL PANEL
10
WARNING
LIGHT OPERATION INSTRUCTIONS
Ÿ Do not let the electrical supply cord hang over the
edge of a table or touch any heated surface.
Ÿ Use the shortest length extension cord required.
Ÿ Do not connect 2 or more extension cords
together.
Ÿ To protect against electrical shock, do not
immerse cord or plugs in water or other liquid.
Ÿ Unplug from the outlet when not in use and before
cleaning. Allow to cool before putting on or
taking off parts.
Ÿ Do not operate grill with a damaged cord, plug or
after the appliance malfunctions or has been
damaged in any manner. Contact the
manufacturer for repair.
Ÿ Do not use an outdoor cooking gas appliance for
purposes other than intended.
Ÿ When connecting, first connect plug to the
outdoor cooking gas appliance then plug
appliance into the outlet.
Ÿ Never remove the grounding plug or use with an
adapter of 2 prongs.
Ÿ Use only extension cords with a 3 prong
grounding plug, rated for the power of the
equipment, and approved for outdoor use with a
W-A marking.
IMPORTANT
Ÿ Since 1971 the National Electrical Code (NEC) has
required Ground Fault Interrupter devices on all
outdoor circuits.
Ÿ If your residence was built before 1971, check with
a qualified electrician to determine if a Ground
Fault Interrupter (GFI) protector exists.
Ÿ Do not use this appliance if the circuit does not
have GFI protection.
Ÿ Do not plug this appliance into an indoor circuit.
Light Operations
1. Make sure light switch on the control panel is in the “OFF” position.
The button should be flat with the rim.
2. Connect the light plug to a GFI outlet or an extension cord, then put
the extension cord plug into the outlet on the wall.
3. Turn the light switch to “ON” by pressing the button. Turn “OFF”
by pressing the button again.
Light plug
Extension cord,
for outdoor use
OFF POSITION
ON POSITION
11
3. Pull out bulb and replace with a new bulb.
4. Reverse instructions from step 2 through step 1 to re-install
socket.
IMPORTANT
Take care not to touch the bulb with your bare fingers.
Touching bulb with your skin can leave a film on the
bulb that causes it to burn out quickly.
Cleaning the Lens
1. Prior to cleaning, make sure the light switch is in the “OFF”
position and the light plug is disconnected from the power
suply.
2. Do not clean the glass lens when warm. Allow to cool before
cleaning. Sudden change in temperature may cause cracking
of the glass lens.
3. Use a damp towel to clean the surface of the glass lens.
4. Allow the lens to dry before reconnecting the light plug to the
power supply and pressing the light switch to the “ON”
position.
Bulb Replacement
Note: Make sure light switch on the control panel is in the “OFF”
position and adapter plug is disconnected from outlet.
Standard Replacement Bulb Specification:
Bulb Type: Halogen
Wattage: 10 W per bulb
Voltage: 12 V
1. Release the screw securing the light socket.
2. Take out the socket and remove the lens.
Can be purchased at
a local hardware store
12
LIMITED LIFETIME WARRANTY:
Saber warrants the fabricated stainless steel components (lids, lid inserts, exterior fire box and cart panels), to be free from defects in
material and workmanship under normal residential use for the lifetime of the product.
Saber’s Limited Lifetime Warranty covers the structural integrity of the lids, lid inserts, exterior firebox and cart panels. Should
structural deterioration occur to the degree of non performance, the part(s) will be replaced, free of change to the consumer for
installation. Costs associated with the installation of replacement warranty parts is not covered by this limited lifetime warranty and is
the sole responsibility of the owner.
This warranty excludes discoloration, surface scratches, weather and atmospheric related staining, and minor surface rust and
oxidation which are normal conditions and to be expected with any outdoor product.
TEN YEAR LIMITED WARRANTY: Saber warrants the stainless steel burner tubes and carryover tubes to be free from defects in
materials and workmanship under normal residential use for a period of ten (10) years from the original date of purchase. The part will
be replaced, free of charge.
FIVE YEAR LIMITED WARRANTY: Saber warrants the stainless steel cooking grates, emitters, warming racks, grease tray, burner boxes,
side burner grate, side burner pan, and porcelain enameled warming racks, grates, and burner boxes to be free from defects in materials
and workmanship for a period of five (5) years from the original date of purchase. The part will be replaced free of charge.
TWO YEAR FULL WARRANTY: Saber warrants all painted parts and any other parts not specifically mentioned above, to be free from
defects in materials and workmanship under normal residential use for a period of two (2) years from the original date of purchase.
Saber will replace the part which fails or is found to be defective during the warranty period, at no cost to the original purchaser.
Owner shall be responsible for proper installation, providing normal care and maintenance, and providing proof of purchase upon
request.
Saber reserves the right, PRIOR to shipping warranty replacement parts, to require the part in question be returned for inspection and
analysis. Requested parts should be returned to Saber, freight pre-paid by the consumer.
WARRANTY LIMITATIONS & EXCLUSIONS
This warranty excludes units purchased for use in all types of commercial and or community use locations such
as restaurants, hotels, catering operations food service establishments, condominium/apartment complexes,
rental properties, and to products with altered or removed serial numbers.
This warranty shall apply ONLY to the products purchased and located in the continental United States and Canada.
Item Warranty Term
Stainless Steel Parts
Lids & Lid inserts Limited Lifetime
Firebox & Cart Panels Limited Lifetime
Burner Tubes & Carryover Tubes 10 Years
Cooking Grates, Emitters, Warming Racks, Grease 5 Years no rust through or burn through
Porcelain Enameled Parts
Lid Insert Limited Lifetime (excludes fading)
Interior Firebox Limited Lifetime no rust through or burn
through (excludes fading)
Warming Racks, Grates, Burner Boxes 5 Years no rust through or burn through
(excludes fading)
Painted Parts 2 Years (excludes fading)
All Other Parts 2 Years
Tray, Burner Boxes, Side Burner Grate, Side Burner
Pan
13
The warranty coverage begins on the original date of purchase and proof of date of purchase is required for warranty service. Please
register your product and retain your original sales receipt.
In order to activate the warranty, we require that you send in the attached warranty registration card or register your product online.
This warranty applies only to the original grill owner and cannot/may not be transferred.
This warranty does not apply to damages resulting from negligence, alteration, misuse, abuse, accident, natural disaster, loss of
electrical power to the product for any reason, improper installation or improper operation, unauthorized adjustments or calibrations,
dings, dents, scratches, or damages due to harsh cleaning chemicals.
Saber shall not be liable for incidental, consequential, special or contingent damages resulting from its breach of this written warranty or
any implied warranty.
In the event of any warranty replacement, all removal, replacement and installation are the responsibility of the grill owner.
Saber reserves the right to replace any defective product with a product equal in value to the original purchase price. Warranty repair
or replacement is at the sole discretion of Saber.
Dealers and Distributors may not, under any circumstances, adjust, alter or extend the conditions and terms of the original warranty.
Your Saber warranty does not cover the following:
Ÿ Labor charges related to installation or set-up, diagnosis of a problem, or repairs.
Ÿ Normal recommended routine maintenance and care.
Ÿ Damage resulting from accident, alteration, misuse, abuse, hostile environments, improper installation, or installation not in
accordance with local, state and federal codes and regulations.
Ÿ The use of unauthorized or “universal” parts.
Ÿ Damage or corrosion caused by lack of maintenance, neglect in following the manufacturer’s care and usage instructions,
grease fires, animals and insects.
Ÿ Any damage resulting from the commercial and or community use of this product.
Ÿ Retail display models are generally sold “AS IS.” If you have purchased a display model, please be advised that it is sold “AS
IS” and that it is subject to the following warranty exclusions:
Ÿ Any exterior or cosmetic damage is non-warrantable
Ÿ Any missing components will be replaced at the consumer’s sole expense.
DISCLAIMER OF IMPLIED WARRANTIES AND LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR
REPLACEMENT AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED OR LIMITED TO ONE YEAR OR THE SHORTEST
PERIOD ALLOWED BY LAW. SABER SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
SOME STATES OR PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUETIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTY OF MERCHANTIBILITY
OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH CAN VARY FROM STATE TO STATE
OR PROVINCE TO PROVINCE.
14
How to Obtain Warranty Service or Repair Parts:
Prior to contacting your dealer or calling us directly, please make sure your grill is registered. You can register your grill at:
http://www.sabergrills.com/registration.
Call your authorized Saber dealer. A list of Saber dealers and their contact information can be found at http://www.sabergrills.com.
Utilize our online customer service at http://www.sabergrills.com/warranty service.
Call Saber directly at 1-(888)-94S-ABER (947-2237). We look forward to assisting you!
Or write us at: Saber
Warranty Service
P. O. Box 1977
Columbus, GA. 31902
Please be prepared to furnish the following information: Purchaser’s name, model and serial number of the grill, date of purchase
and the accurate description of the problem.
Date of Purchase:
Dealer Where You Purchased Your Grill:
Dealer Phone Number:
Model Number:
(located on the cover of your instruction manual or rating label)
Serial Number:
(located on the cover of your instruction manual or rating label)
®
PARTS LIST
15
Key Qty Description
A 1 KIT, Bottom Shelf Assembly
B 4 Caster, Locking
C 1 Right Cart Panel
D 1 Left Cart Panel
E 1 Rear Cart Panel
F 1 Front Door Brace
G 1 Center Cart Panel
H 1 KIT, Right Door w/ Hinges
I 1 KIT, Door Hinges (SET of 2)
J 1 KIT, Door Magnets (SET of 2)
K 1 Door Closer Bracket
L 1 KIT, Striker Plates (SET of 2)
M 2 Drawer Assembly
N 1 Condiment Basket
O 1 KIT, Handles for Door and Drawers (SET of 3)
P 2 KIT, Drawer Slides (SET of 2)
Q 1 Grommet, for Light Cord
R 1 Grommet, for NG Conversion Hose Hole
S 1 KIT, Ignition Module
T 1 KIT, Tank Tray
U 1 Drawer Top Panel
V 1 KIT, Transformer for Halogen Grill Light
W 1 Grate Cleaning Tool
X 1 KIT, Lid Assembly
Y 1 KIT, Logo Plate
Z 1 KIT, Lid Handle
AA 1 KIT, Lid Shoulder Bolt (SET of 2)
BB 1 KIT, Lid Stop, Silicone, (SET of 4)
CC 1 KIT, Firebox Assembly
DD 1 Warming Rack
EE 1 KIT, Light for Halogen Grill Light (SET of 2)
FF 1 KIT, Right Shelf Assembly w/ Tool Holders
GG 4 KIT, Cooking Grate with Emitter
HH 4 KIT, Burner Box
II 4 KIT, Burner w/ Carryover
JJ 1 Electrode w/ Ignition Wire, 850 mm
KK 1 Electrode w/ Ignition Wire, 1110 mm
LL 1 Electrode w/ Ignition Wire, 1315 mm
MM 1 Electrode w/ Ignition Wire, 1510 mm
NN 1 KIT, Control Console, w/ Valve Assembly and Switches
OO 1 KIT, Ignition Switch Module w/ Wires
PP 1 Switch for Halogen/LED Grill Lights
QQ 4 Temperature Gauge, UFC, w/ Clip
RR 4 LED Light
SS 1 LED Wire Harness
TT 4 Control Knob
UU 4 KIT, Bezel
V V 1 KIT, Sideburner Shelf Assembly
WW 2 Control Knob, for Sideburner
XX 2 KIT, Bezel, for Sideburner
YY 1 Sideburner Grate, SS Wire
ZZ 1 KIT, Burners for Dual Sideburner
Key Qty Description
AAA 1 KIT, Sideburner Lid
BBB 1 Sideburner Pan with Lid Stop
CCC 1 KIT, Electrode for Sideburner with Wire
DDD 1 KIT, Wind Deflector
EEE 4 KIT, Firebox Heat Shield
FFF 1 Grease Tray Assembly
GGG 1 KIT, Grease Tray Supports (SET of 2)
HHH 1 Match Holder w/ Chain
III 1 KIT, Firebox Mounting Posts (SET of 4)
JJJ 1 KIT, Rotisserie Rod Brackets (SET of 2)
NOT Pictured
1 Hardware Pack
1 Assembly Guide, English/ Spanish/ French
1 Product Guide, English/ Spanish/ French
1 Grill Cover
1 KIT, Rotisserie
1 Rotisserie Rod
V
BB
II
AA
QQ
JJ
KK
LL
RR
PP
FFF
MM
EE
BBB
HH
OO
850 mm
1110 mm
1315 mm
1510 mm
PARTS DIAGRAM
A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
Q
R
S
T
U
W
X
Y
Z
CC
DD
FF
GG
NN
TT
UU
WW
XX
V V
AAA
ZZ
YY
CCC
DDD
EEE
SS
HHH
III
GGG
O
16
JJJ
17
Problem Possible Cause
Prevention/Solution
Troubleshooting
GAS ISSUES:
Burner(s) will not light
using ignitor. See
Electronic Ignition
Troubleshooting also.)
Continued on next
page.
Trying to light wrong burner.
Burner not engaged with control valve.
Obstruction in burner.
No gas flow.
Vapor lock at coupling nut to LP cylinder.
Coupling nut and LP cylinder valve not fully
connected.
See instructions on door panel and in Use and Care section.
Make sure valves are positioned inside of burner tubes.
Ensure burner tubes are not obstructed with spider webs or other
matter. See cleaning section of Use and Care.
Make sure LP cylinder is not empty. If LP cylinder is not empty, refer
to “Sudden drop in Gas Flow.”
Turn control knobs to OFF and disconnect coupling nut from
LP cylinder. Wait 30 seconds, reconnect and retry.
Turn the coupling nut approximately one-half to three-quarters
additional turn until solid stop. Tighten by hand only-do not use tools.
ELECTRICAL ISSUES:
Electrode cracked or broken; “sparks at
crack.”
Electrode tip not in proper position.
Wire and/or electrode covered with cooking
residue.
Replace electrode(s).
Tip of electrode should be pointing toward gas port opening on
burner. The distance should be 1/8” to 1/4”. Adjust if necessary.
Clean wire and/or electrode with rubbing alcohol and clean swab.
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.
Emergencies Possible Cause Prevention/Solution
EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department.
Gas leaking from
cracked/cut/burned
hose.
Gas leaking from LP
cylinder.
Gas leaking from LP
cylinder valve.
Gas leaking between
LP cylinder and
regulator connection.
Fire coming through
control panel.
Grease fire or
continuous excessive
flames above cooking
surface.
Damaged Hose.
Mechanical failure due to rusting or
mishandling.
Failure of cylinder valve from mishandling
or mechanical failure.
Improper installation, connection not tight,
failure of rubber seal.
Fire in burner tube section of burner due to
blockage.
Too much grease buildup in burner area.
Turn OFF gas at LP cylinder. If anything got burned, replace
valve/hose/regulator. If burned, discontinue use of product until a
plumber has investigated cause and corrections are made.
Replace LP cylinder.
Turn OFF LP cylinder valve. Return LP cylinder to gas supplier.
Turn OFF LP cylinder valve. Remove regulator from cylinder and
visually inspect rubber seal for damage. See LP Cylinder Leak Test
and Connecting Regulator to the LP Cylinder.
Turn control knobs to OFF and LP cylinder valve OFF. Leave lid
open to allow flames to die down. After fire is out and grill is cold,
remove burner and inspect for spider nests or rust. See Natural
Hazard and Cleaning the Burner Assembly pages.
Turn control knobs to OFF and LP cylinder valve OFF. Leave lid
open to allow flames to die down. After cooling, clean food particles
and excess grease from inside firebox area, grease tray and other
surfaces.
18
Problem Possible Cause
ELECTRICAL ISSUES CON’T.:
Prevention/Solution
Troubleshooting (continued)
Burner(s) will not light
using ignitor. (See
Electronic Ignition
Troubleshooting also).
Continued.
Burner(s) will not match
light.
Sudden drop in gas
ow or low ame.
Flames blow out.
Flare-up.
Persistent grease re
Flashback (re in
burner tube(s)).
Unable to ll LP tank.
One burner does not
light from other
burner(s).
Wires are loose or disconnected.
Wires are shorting (sparking) between
ignitor and electrode.
Dead battery.
No spark, no ignition noise.
No spark, some ignition noise.
Sparks, but not at electrode or at full
strength.
See “GAS ISSUES:” on previous page.
Match will not reach
Improper method of match-lighting.
Out of gas.
Excess ow valve tripped.
Vapor lock at coupling nut/LP tank
connection.
High or gusting winds
Low on LP gas.
Excess ow valve tripped.
Grease buildup.
Excessive fat in meat.
Excessive cooking temperature.
Grease trapped by food buildup around
burner system.
Burner and/or burner tubes are blocked.
Some dealers have older ll nozzles with
worn threads.
Grease buildup or food particles in end(s) of
carryover tube(s).
Reconnect wires or replace electrode/wire assembly.
Replace ignitor wire/electrode assembly.
Replace with a new alkaline battery.
See Section l of Electronic Ignition System.
See Section ll of Electronic Ignition System.
See Section lll of Electronic Ignition System.
Use long-stem match (replace match)
See “Match-Lighting” section of Use and Care.
Check for gas in LP tank.
Turn control knobs to OFF, wait 30 seconds and light grill. If ames
are still low, turn off knobs and LP tank valve. Disconnect regulator.
Reconnect regulator and leak-test. Turn on LP tank valve, wait 30
seconds and then light grill.
Turn off knobs and LP tank valve. Disconnect coupling nut from tank.
Reconnect and retry.
Turn front of grill to face wind or increase ame height.
Rell LP tank.
Refer to “Sudden drop in gas ow” above.
Clean burners and inside of grill/rebox.
Trim fat from meat before grilling.
Adjust (lower) temperature accordingly.
Turn knobs to OFF. Turn gas off at LP tank. Leave lid in position
and let re burn out. After grill cools, remove and clean parts.
Turn knobs to OFF. Clean burner and/or burner tubes. See burner
cleaning section of Use and Care manual.
The worn nozzles don’t have enough “bite” to engage valve. Try a
second LP dealer.
Clean carryover tube(s) with a wire brush.
ELECTRONIC IGNITION:
19
Troubleshooting - Electronic Ignition
No sparks appear at
any electrodes when
Electronic Ignition
Button is pressed; no
noise can be heard
from spark module.
No sparks appear at
any electrodes when
Electronic Ignition
Button is pressed;
noise can be heard
from spark module.
Sparks are present but
not at all electrodes
and/or not at full
strength.
Problem (Ignition) Possible Cause Check Procedure Prevention/Solution
SECTION l
Battery not installed
properly.
Dead battery.
Button assembly not
installed properly.
Faulty spark module.
Switch wires
disconnected.
Output lead connections
not connected.
Output lead connections
not connected.
Arcing to grill away from
burner(s).
Weak battery.
Electrodes are wet.
Electrodes cracked or
broken “sparks at crack”.
SECTION ll
SECTION lll
Check battery orientation.
Has battery been used
previously?
Check to ensure threads are
properly engaged. Button
should travel up and down
without binding.
If no sparks are generated with
new battery and good wire
connections, module is faulty.
Check to ensure switch wires
are connected.
Are output connections on and
Tight?
Are output connections on and
tight?
If possible, observe grill in dark
location. Operate ignition
system and look for arcing
between output wires and grill
frame.
All sparks present but weak or
at slow rate.
Has moisture accumulated on
electrode and/or in burner
ports?
Inspect electrodes for cracks.
Install battery (make sure that “+” and “-”
connectors are oriented correctly, with “+” end up
and “-” end down.
Replace battery with new alkaline battery.
Remove battery cap and reinstall, making sure it
can be fully engaged.
Replace spark module.
Reconnect switch wires.
Remove and reconnect all output connections at
module and electrodes.
Remove and reconnect all output connections at
module and electrodes.
If sparks are observed other than from burner(s),
wire insulation may be damaged. Replace wires.
Replace battery with a new alkaline battery.
Use paper towel to remove moisture.
Replace cracked or broken electrodes.
Troubleshooting - LED Lights
LED lights do NOT
illuminate when light
switch is pressed ON,
but LED light switch
illuminates.
LED lights do NOT
illuminate when light
switch is pressed ON,
AND LED light switch
does NOT illuminate.
LED lights DO
illuminate when light
switch is pressed ON,
but LED light switch
does NOT illuminate.
Problem (Lights) Possible Cause Check Procedure Prevention/Solution
LED wires disconnected.
Faulty LED light(s).
Transformer lead wires
disconnected (if used).
Switch wire harness
disconnected.
Bad LED light switch.
Check to ensure that wires at
each LED spade terminal are
firmly connected and not loose
behind control panel.
If good connection at LED, and
other LED lights are
operational, then bad LED.
Check that transformer output
connector is engaged and
locked with no loose wires at
the connectors.
Check that the switch wire
harness is connected properly
to back of switch.
Switch wire harness is
attached and LED lights
illuminate.
Reconnect wires at spade connectors on the LED.
If wires will not stay attached and are loose,
contact Saber for warranty replacement parts.
Contact Saber for a warranty replacement part.
Reconnect the transformer wire connectors. If
wires pull loose from the connectors, contact
Saber for warranty replacement parts.
Reconnect switch wire harness to switch ensuring
that harness locks to switch.
Contact Saber for a warranty replacement part.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Saber Compact R67SC0917 Manuel utilisateur

Catégorie
Barbecues
Taper
Manuel utilisateur