KitchenAid KSSO36QMB02 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSSO36QMB02

Catégorie: Frigos

Taper: Le manuel du propriétaire

®itchen_kid ®

SIDE BY SIDE BUILT-IN REFRIGERATOR

For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230

In Canada, call for assistance 1-800-461-5681, for installation and service, call: 1-800-807-6777 or visit our website at...

www.kitchenaid.com or www.KitchenAid.ca

REFRIGERADOR EMPOTRADO DE DOS

PUERTAS

Pars consultas respecto a caracteristicas, operaci6n/desempe_o, partes, accesorios o servicio, Ilame al: 1-800-422-1230

En CanadA, pars obtener asistencia Ilame al 1-800-461-5681, pars instalaci6n y servicio Ilame al: 1-800-807-6777 o

visite nuestra pagina de Internet... www.kitchenaid.com o www.KitchenAid.ca

REFRIGERATEUR ENCASTRE COTE A COTE

Au Canada, pour assistance composez le 1-800-461-5681, pour installation ou service composez le 1-800-807-6777 ou visitez notre site web &...

www.KitchenAid.ca

Table of Contents/Indice/Table des matieres .................................................................. 2

2266808A

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

BEFORE USE .................................................................................. 4

REFRIGERATOR USE .................................................................... 4

Power On/Off Switch ................................................................... 4

Water System Preparation ........................................................... 5

Normal Sounds ............................................................................ 6

Ensuring Proper Air Circulation .................................................... 6

Using Controls .............................................................................. 6

Water and Ice Dispensers ............................................................ 8

Water Filtration System ................................................................ 9

Ice Maker and Storage Bin ........................................................ 10

REFRIGERATOR FEATURES ...................................................... 11

Refrigerator Shelves ................................................................... 11

Ingredient Care Center ............................................................... 11

Crisper and Covers .................................................................... 12

Covered Utility Bin ..................................................................... 12

Wine Rack .................................................................................. 12

FREEZER FEATURES .................................................................. 12

Freezer Shelf ............................................................................... 12

Freezer Basket ............................................................................ 12

DOOR FEATURES ........................................................................ 13

Utility Compartment ................................................................... 13

Door Bins .................................................................................... 13

REFRIGERATOR CARE ............................................................... 13

Cleaning ...................................................................................... 13

Changing the Light Bulbs ........................................................... 14

Power Interruptions .................................................................... 14

Vacation Care ............................................................................. 15

TROU BLESI-IOOTING .................................................................. 15

ASSISTANCE OR SERVICE ......................................................... 18

In the U.S.A................................................................................ 18

In Canada ................................................................................... 18

Accessories ................................................................................ 18

WATER FILTER CERTIFICATIONS ............................................. 18

PRODUCT DATA SHEETS ........................................................... 19

WARRANTY .................................................................................. 20

INDICE

SEGURIDAD DEL REFRIGERADOR ........................................... 21

CGmo deshacerse adecuadamente de su refrigerador viejo....21

ANTES BE MSAR .......................................................................... 22

USO DE SU REFRIGERADOR ..................................................... 22

Interrupter de Encendido/Apagado ........................................... 22

PreparaciGn del sistema de agua .............................................. 23

Sonidos normales ...................................................................... 24

CGmo asegurar la debida circulaciGn del aire ........................... 24

Uso de los controles .................................................................. 24

Despachadores de agua y hielo ................................................ 27

Sistema de filtraciGn de agua .................................................... 28

Fabrica de hielo y dep6sito ........................................................ 29

CARACTERiSTICAS DEL REFRIGERADOR .............................. 30

Estantes del refrigerador ............................................................ 30

Centre de cuidado de ingredientes ........................................... 30

Cajones para verduras y tapas .................................................. 31

Compartimiento de uso general con tapa ................................. 31

Portabotellas .............................................................................. 31

CARACTERiSTICAS DEL CONGELADOR ................................. 31

Estante del congelador .............................................................. 31

Canastilla del congelador ........................................................... 32

CARACTERiSTICAS DE LA PUERTA ......................................... 32

Compartimiento utilitario ............................................................ 32

Recipientes de las puertas ......................................................... 32

CMIDADO DE SU REFRIGERABOR ............................................ 32

Limpieza ..................................................................................... 32

CGmo cambiar los focos ............................................................ 33

Cortes de corriente ..................................................................... 34

Cuidado durante las vacaciones ................................................ 34

SOLUCION DE PROBLEMAS ...................................................... 34

AYUDA O SERVICIO TI_CNICO ................................................... 38

En los EE.UU.............................................................................. 38

En Canada .................................................................................. 38

Accesorios .................................................................................. 38

NOJA DE DATOS DEL PRODUCTO ........................................... 39

GARANT|A ..................................................................................... 40

TABLE DES MATIERES

SI_CURITE DU REFRIGERATEUR .............................................. 41

Mise au rebut de votre vieux refrigerateur ................................. 41

AVANT L'UTILISATION ................................................................ 42

UTILISATION DU RI_FRIGI_RATEUR .......................................... 42

Commutateur marche/arr_t ....................................................... 42

Preparation du syst_me d'eau ................................................... 43

Sons normaux ............................................................................ 44

Pour s'assurer d'une circulation d'air appropriee ..................... 44

Utilisation des commandes ........................................................ 44

Distributeurs d'eau et de glagons .............................................. 47

Systeme de filtration d'eau ........................................................ 48

Machine a glagons et bac/seau d'entreposage ........................ 49

CARACTERISTIQUES DU REFRIGI_RATEUR ........................... 50

Tablettes du refrigerateur ........................................................... 50

Centre de soins des ingredients ................................................ 50

Bac a legumes et couvercles ..................................................... 51

Casier utilitaire couvert ............................................................... 51

Casier a vin ................................................................................. 51

CARACTERISTIQUES DU CONGI_LATEUR ............................... 51

Tablette de congelateur ............................................................. 51

Panier du congelateur ................................................................ 52

CARACTERISTIQUES DE LA PORTE ......................................... 52

Compartiment utilitaire ............................................................... 52

Compartiments dans la porte .................................................... 52

ENTRETIEN BU RI_FRIGERATEUR ............................................ 52

Nettoyage ................................................................................... 52

Remplacement des ampoules d'eclairage ................................ 53

Pannes de courant ..................................................................... 54

Entretien avant les vacances ..................................................... 54

DEPANNAGE ................................................................................. 55

ASSISTANCE OU SERVICE ......................................................... 58

Accessoires ................................................................................ 58

FEUILLES BE BONNI_ES SUR LE PROBUIT ............................. 59

GARANTIE ..................................................................................... 60

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

mPlug into a grounded 3 prong outlet, m Use nonflammable cleaner.

mDo not remove ground prong.

mDo not use an adapter.

mDo not use an extension cord.

mDisconnect power before servicing.

mReplace all panels before operating.

mRemove doors from your old refrigerator.

m Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

m Use two or more people to move and install refrigerator.

m Disconnect power before installing ice maker (on ice maker

kit ready models only).

m Use a sturdy glass when dispensing ice or water (on some

models).

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of

your old refrigerator, please follow these instructions to help

prevent accidents.

BEFORE USE

Removing Packaging Materials

• Remove tape and glue residue from surfaces before turning on

the refrigerator. Rub a small amount of liquid dish soap over

the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

Cleaning Before Use

After you remove all of the packaging materials, clean the inside

of your refrigeratoer before using it. See the cleaning instructions

in "Refrigerator Care."

important information to know about glass she_ves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold= Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping=

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal= Giass

shelves and covers are heavy= Use special care when

removing them to avoid impact from dropping=

REFRIGERATOR USE

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or eiectdca_ shock,

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

If you need to turn the power to your refrigerator ON or OFF, you

must remove the top grille assembly to access the On/Off switch.

Turn the power to the refrigerator OFF when cleaning product or

changing light bulbs.

Classic, Overlay and Complete Series

To remove top grille:

1. Grasp both ends of the top grille.

2. Push the top grille straight up, then pull straight out. Lay the

grille on a soft surface.

B A B

A. Top grille

B. Cabinet side trims

To replace top grille:

1. Insert top grille hooks (located on the back of the top grille)

into the slots on the side trim.

2. Pull grille down slightly to lock into place.

Architect ®Series

To remove top grille:

1. Grasp both ends of louver panel. Push louver panel straight

up, then pull straight out. Lay the panel on a soft surface.

2. Grasp both ends of the top grille. Push top grille straight up,

then pull straight out. Lay the top grille on a soft surface.

B A B

A. Top grille

B. Cabinetside trim

C.Louver panel

To replace top grille:

Insert top grille hooks (located on the back of the top grille

panel) into the slots on side trim. Pull grille down slightly to

lock into place.

2. Insert louver panel hooks (located on the back of the louver

panel) into the slots on the side trim. Pull panel down slightly

to lock into place.

Pro Line TM Series

To remove top grille:

1. Grasp both ends of the top grille.

2. Push the top grille straight up, and then pull straight out.

3. Disconnect the wirinc harness from the back of the top grille.

4. Lay the grille on a soft surface.

5. Place wiring on the top of the cabinet, ensuring it is out of the

way of the doors.

To replace top grille:

1. Reattach wiring harness into grille back.

2. Insert top grille hooks into slots on the side trim. Pull grille

down slightly to lock into place.

To Turn Power On or Off:

1. Remove top grille.

2. Press main power switch to the ON or OFF position.

3. Replace top grille.

IMPORTANT: Be sure the power switch is set to the ON position

after cleaning refrigerator or changing light bulbs.

iiii

A. Power On/Off switch

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. For Style 1,

lift up the wire shutoff arm as shown. For Style 2, move the

switch to the OFF (right) setting as shown. The ON/OFF

switch is located on the top right side of the freezer

compartment.

Style 1

Style 2

NOTES:

• If your model has a base grille filter system, make sure the

base grille filter is properly installed and the cartridge cap

handle is in the horizontal position.

Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction

may be used on disinfected waters that may contain

filterable cysts.

Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by

dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.

Cleaning the system will take approximately 6 to 7 minutes

and will help clear air from the line. Additional flushing may be

required in some households.

NOTE: As air is cleared from the system, water may spurt out

of the dispenser.

Open the freezer door and turn on the ice maker. For Style 1,

lower the wire shutoff arm. For Style 2, move the switch to

the ON (left) position. Please refer to the "Ice Maker and

Storage Bin" section for further instructions on the operation

of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Your new refrigerator may make sounds that your old one didn't

make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your refrigerator is equipped with an ice maker, you will hear

a buzzing sound when the water valve opens to fill the ice

maker for each cycle.

Your refrigerator is designed to run more efficiently to keep

your food items at the desired temperatures and to minimize

energy usage. The high efficiency compressor and fans may

cause your refrigerator to run longer than your old one. You

may also hear a pulsating or high-pitched sound from the

compressor or fans adjusting to optimize performance.

You may hear the evaporator fan motor circulating air through

the refrigerator and freezer compartments. The fan speed

may increase as you open the doors or add warm food.

Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.

Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.

As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.

Contraction and expansion of the inside walls may cause a

popping noise.

You may hear air being forced over the condenser by the

condenser fan.

You may hear water running into the drain pan during the

defrost cycle.

))): _

In order to ensure proper temperatures, you need to permit

airflow between the two sections. Cold air enters the bottom of

the freezer section and moves up. It then enters the refrigerator

section through the top vent. Air then returns to the freezer as

shown.

/ii .............................

Do not block any of these vents with food such as soda, cereal,

bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent

odor transfer from food, wrap or cover foods tightly.

IMPORTANT:

• The refrigerator control adjusts the refrigerator compartment

temperature. The freezer control adjusts the freezer

compartment temperature.

Wait 24 hours after you turn on the refrigerator before you put

food into it. If you add food before the refrigerator has cooled

completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer controls to a

lower (colder) setting will not cool the compartments any

faster.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not

blocked before adjusting the controls.

The preset settings should be correct for normal household

usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.

NOTE: The factory recommended set points are 0°F (-18°C)for

the freezer and 37°F (3°C) for the refrigerator.

Turning Refrigerator On and Viewing Set Points

Press and hold POWER (ON/OFF) for 2 seconds.

Warmer Warmer

@ EFO'O RATOR(D

(2)

Colder Colder

NOTE: After the refrigerator is turned on, the Over Temperature

audio alarm and indicator light will activate every 11/2hours until

the refrigerator and freezer temperatures are below 48°F (9°C)

and 15°F (-9°C), respectively, or until the alarm is turned off. To

turn off the audio alarm and indicator light, see "Master Alarm

Reset."

Viewing the Celsius Temperatures

Press °C SELECT touch pad. The negative sign (-) will light

up. To redisplay degrees Fahrenheit, press °C SELECT again.

NOTE: If the freezer temperature is below zero, the negative sign

next to the freezer display will light up. This is normal.

Adjusting Controls

NOTE: Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To adjust set point temperatures:

• Press the refrigerator or freezer PLUS (+) or MINUS (-) key

pad until the desired temperature is reached.

Warmer

REFRIGERATOR Q

Colder

NOTE: The set point range for the freezer is -5°F to 6°F (-21 °C to

-14°C). The set point range for the refrigerator is 34°F to 46°F

1°C to 8°C).

CONDITION/REASON: 1EMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control 1°

Not set correctly for conditions higher

REFRIGERATOR too warm REFRIGERATOR Control 1°

lower

High use or room very warm

FREEZER too cold FREEZER Control 1° higher

Not set correctly for conditions

FREEZER too warm/too little FREEZER Control 1° lower

ice

High use or heavy ice use

Water Filter Status & Reset

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may

be used on disinfected waters that may contain filterable

cysts.

The water filter display will help you know when it is time to

change your filter. To change the filter, see the "Water Filtration

System" section.

INDICATOR: STATUS:

99 percent New filter installed

10 percent Order replacement filter

0 percent or flow decreases Replace filter

• After replacing the water filter, press RESET and hold for

2 seconds to change the water filter display to 99 percent.

WATER FILTER

PERCENTLEFT

Max Cool

The Max Cool feature assists with periods of heavy ice usage, full

grocery loads, or temporarily warm room temperatures.

• Press MAX COOL to turn on the Max Cool feature. The Max

Cool indicator light will remain on for 24 hours unless

manually turned off.

NOTE: The temperature display will remain at 34°F (1°C) and -5°F

(-21 °C) for the refrigerator and freezer compartments,

respectively, while the Max Cool feature is enabled. After

24 hours, the refrigerator returns to the previous temperature set

points.

Holiday Mode

The Holiday Mode feature is designed for the traveler or for those

whose religious observances require turning off the lights and

icemaker. By selecting this feature, the temperature set points

remain unchanged, the ice maker will be disabled and the interior

lights will turn off. On some models, the Holiday Mode feature

won't disable the ice and water dispenser. For these models the

lock button can be used to disable the ice and water functions,

but depressing the ice or water lever will still turn on the

dispenser light. For most efficient refrigerator operation, it is

recommended to exit the Holiday Mode when it is no longer

required.

• Press HOLIDAY MODE to turn on the Holiday Mode feature.

This feature will remain on until the Holiday Mode key is

pressed again.

oliday

NOTE: If the Max Cool feature has been selected prior to

turning on the Holiday Mode feature, then the set points will

remain at 34°F (1°C) and -5°F (-21 °C) for the refrigerator and

freezer compartments, respectively, until the Max Cool

feature times out. The refrigerator will then return to the

previous temperature set points chosen prior to the selection

of the Max Cool feature, but the lights and ice maker will

remain off until the Holiday Mode key is pressed again.

Alarm Functions

Master Alarm Reset

Pressing the OVER TEMPERATURE RESET will shut off the audio

alarm, but this does not affect the indicator light the first time the

OVER TEMPERATURE RESET is pressed. The indicator light will

shut off once the OVER TEMPERATURE RESET is pressed the

second time. The audio alarm will not sound again for the current

condition that caused the alarm until a new condition occurs or

until a Master Alarm Reset is performed.

A Master Alarm Reset can be performed by pressing the POWER

(ON/OFF) twice or by turning the power to the refrigerator off and

on again. See "Power On/Off Switch." The indicator light will

reactivate after the OVER TEMPERATURE RESET is pressed if

the condition that caused the alarm is still present. See "Over

Temperature," "Call Service," or "Door Open."

Over Temperature

The Over Temperature feature is designed to let you know when

either the refrigerator temperature rises above 48°F (9°C) or the

freezer temperature rises above 15°F (-9°C) for longer than

11/2hours. The audio alarm will shut off automatically when the

temperature returns to normal, but the indicator light will continue

to flash to let you know that an over temperature condition has

occurred until the OVER TEMPERATURE RESET is pressed.

If the over temperature condition is still present when an Over

Temperature Reset is performed, the indicator light will continue

to reactivate every 11/2hours until refrigerator and freezer

temperatures are below 48°F (9°C) and 15°F (-9°C), respectively.

IMPORTANT: Ifthe Over Temperature Alarm activates, your food

may spoil. See the "Power Interruptions" section for more

information and minimize door openings until temperatures return

to normal.

NOTE: To deactivate the audio alarm and indicator light, see

"Master Alarm Reset."

CallService

IftheCallServiceindicatorlightisflashing,callforservice.See

the"AssistanceorService"sectionforinformationoncallingfor

service.

0 CallService

NOTE: To deactivate the audio alarm and indicator light, see

"Master Alarm Reset."

Door Open

The Door Open indicator light will flash, an alarm will sound and

the interior lights will turn off when a door has been open for

longer than 10 minutes. When the door is closed, the audio alarm

will reset and turn off, but the Door Open indicator light will

continue to flash until the temperature is equal to or below 45°F

(7°C) and 15°F (-9°C) for the refrigerator and freezer

compartments, respectively.

@ Door Open

NOTE: To deactivate the audio alarm and indicator light, see

"Master Alarm Reset."

Top Grille Temperature Display (Pro Line TMModels Only)

The top grille temperature display shows the freezer and

refrigerator temperatures. The display will show either Fahrenheit

or Celsius, depending on the selected reading inside the

refrigerator.

During the defrost cycle, the temperature display will show the

temperature set points.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer. When

the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the

ice bin. Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes

and the ice dispensing stops. The dispensing system will not

operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before

dispensing ice, select which type of ice you prefer. The button

controls are designed for easy use and cleaning.

ICE

CRUSH CUBE

For crushed ice, cubes are crushed before they are dispensed.

This may cause a slight delay when dispensing crushed ice.

Noise from the ice crusher is normal, and pieces of ice may vary

in size. When changing from crushed to cubed, a few ounces of

crushed ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the

glass close to the dispenser opening so ice does not fall

outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to

the lever in order to activate the ice dispenser. Pressing hard

will not make the ice dispense faster or in greater quantities.

A B

A. Freezertemperature display

B.Refrigerator temperature display

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

Depending on your model, you may have one or more of the

following options: the ability to select either crushed or cubed

ice, a special light that turns on when you use the dispenser, or a

lock option to avoid unintentional dispensing.

Remove the glass to stop dispensing.

NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The Water Dispenser

If you did not flush the water system when the refrigerator was

first installed, press the water dispenser bar with asturdy glass or

jar until you draw and discard 2 to 3 gal. (8 to 12 L) or

approximately 6 to 7 minutes of water after water begins

dispensing. It will take 3 to 4 minutes for the water to begin

dispensing. The water you draw and discard cleans the system

and helps clear air from the lines. Allow several hours for the

refrigerator to cool down and chill water.

IMPORTANT: Depending on your model, the small removable

tray at the bottom of the dispenser is designed to catch small

spills and allow for easy cleaning. There is no drain in the tray.

The tray can be removed from the dispenser and carried to the

sink to be emptied or cleaned.

ToDispense Water:

1. Press a sturdy glass against the water dispenser lever.

2. Remove the glass to stop dispensing.

NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense enough water every week to

maintain a fresh supply.

A new water filter should display a reading of 99% and will

continue to decrease as the filter life is used. When display reads

10%, it is time to order a replacement filter. It is recommended

that you replace the base grille water filter cartridge when the

water filter indicator light changes to 0% OR when water flow to

your water dispenser or ice maker decreases noticeably. See

"Changing the Base Grille Filter."

WATER FILTER

The Dispenser Light

The dispenser area has a light. It can be turned on manually by

pressing the ON button (touchpad or rocker switch).

On some models: Whenever you use the dispenser, the lever will

automatically turn the light on.

LIGHT

OFF O N

NOTE: See the "Changing the Light Bulbs" section for

information on changing the dispenser light bulb.

The Dispenser Lock (on some models)

Your dispenser can be turned off for easy cleaning or to prevent

unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the

refrigerator, to the ice maker, or to the dispenser light. It simply

deactivates the dispenser levers.

To turn off the dispenser, press the LOCK button. The indicator

will appear above the LOCK button and the ice and water

dispensers will not work. To unlock the dispenser, press the

UNLOCK button until the indicator appears. Then continue to

dispense ice or water as usual.

DISPENSER

LOCK UNLOCK

PERCENTLEFT

After changing the water filter cartridge, reset the water filter

status light by pressing and holding the RESET button for

2 seconds. The indicator light will change to 99% when the filter

indicator is reset.

Changing the Base Grille Filter

Locate the water filter cartridge cap in the front base grille.

Rotate the cap counterclockwise to a vertical position and

pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur.

Remove the cartridge cap by sliding it off the end of the old

cartridge. The cap will slide to the left or right.

IMPORTANT: Do not discard the cartridge cap. It is part of

your refrigerator. Keep the cartridge cap to use with the

replacement filter.

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

The Base Grille Water Filter Status Light

The water filter indicator display will help you know when to

change your water filter cartridge. The display or light is located

at the top of the refrigerator compartment.

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may

be used on disinfected waters that may contain filterable

cysts.

Slide the cartridge cap onto the new cartridge. See

illustration in Step 2.

With cartridge cap handle in the vertical position, push the

new filter cartridge into the base grille until it stops. Rotate

the cartridge cap clockwise to a horizontal position. Flush the

water system. See "Flushing the Water System After

Replacing Filter."

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until

the water begins to flow. Flush the water system by dispensing

and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the

system will take approximately 6 to 7 minutes and will help clear

air from the line. Additional flushing may be required in some

households.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

Using the Dispenser Without the Water Filter

You can run the dispenser without a water filter cartridge. Your

water will not be filtered.

1. Remove the base grille water filter cartridge.

2. Slide the cartridge cap off the end of the filter cartridge. With

the cartridge cap handle in the vertical position, insert the

cartridge cap into the base grille until it stops.

IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. Rotate the cartridge cap to a horizontal position. The

cartridge cap might not be even with the base grille.

Style I

To turn the ice maker on/off:

The on/off switch for the ice maker is a wire shutoff arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm.

NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice

cubes will raise the wire shutoff arm to the OFF (arm up)

position.

2. To manually turn the ice maker off, lift the wire shutoff arm to

the OFF (arm up) position and listen for the click to make sure

the ice maker will not continue to operate.

To remove and replace the ice bin:

1. Flip up the covering panel.

A .........................

A. Ice maker cover

2. Lift the wire shutoff arm so it clicks into the OFF (up)

position. Ice can still be dispensed, but no more can be

made.

3. Lift up the front of the storage bin and pull the ice bin forward.

4. Replace the bin by pushing it in all the way or the dispenser

will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is

closed tightly.

Style 2

To turn the ice maker on/off:

The on/off switch is located on the top right side of the freezer

compartment.

1. Toturn the ice maker on, slide the control to the ON (left)

position.

NOTE: Your ice maker has an automatic shutoff. The ice

maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the

OFF (right) position.

To remove and replace the ice storage bin:

1. Hold the base of the storage bin with both hands and press

the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to the

OFF (right) position when removing the storage bin. The

sensor cover ("flipper door") on the left wall of the freezer

stops the ice maker from producing ice if the door is open or

the storage bin is removed.

2. Replace the storage bin on the door and push down to make

sure it is securely in place.

To increase ice production rate:

• In normal ice production, the ice maker should produce

approximately 7 to 9 batches of ice in a 24-hour period. If ice

is not being made fast enough, turn the Freezer Control

toward a higher (colder) number. Wait 24 hours between each

increase.

Clean the ice storage bin

Empty the ice container. Use warm water to melt the ice if

necessary.

NOTE: Do not use anything sharp to break up the ice in the

bin or bucket. This can cause damage to the ice container

and the dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry

thoroughly. Do not use harsh or abrasive cleaners or solvents.

REMEMBER

Allow 24 hours to produce the first batch of ice. Allow 3 days

to completely fill ice container.

Discard the first three batches of ice produced to avoid

impurities that may be flushed out of the system.

The quality of your ice will be only as good as the quality of

the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply.

Water softener chemicals (such as salt) can damage parts of

the ice maker and lead to poor quality ice. If a softened water

supply cannot be avoided, make sure the water softener is

operating properly and is well maintained.

It is normal for the ice cubes to be attached at the corners.

They will break apart easily.

For Style 1 ice maker, do not force the wire shutoff arm up or

down.

Do not store anything on top of the ice maker or in the ice

storage bin/bucket.

REFRIGERATOR FEATURES

Important information to know about glass shemves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use speciaI care when

removing them to avoid impact from dropping.

The shelves in your refrigerator are adjustable to meet your

individual storage needs.

Storing similar food items together in your refrigerator and

adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the

amount of time the refrigerator door is open, and save energy.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports. Pull shelf straight out.

2. Replace the shelf/frame by guiding the rear shelf hooks into

the shelf supports. Tilt the front of the shelf up until the rear

shelf hooks drop into the shelf supports.

3. Lower the front of the shelf and check to make sure that the

shelf is securely in position.

The control for the ingredient care center adjusts the storage

temperature of the pan. Cold air flows into the pan through the air

duct between the freezer and the refrigerator. Setting the controls

allows more or less cold air through the air duct.

To adjust the ingredient care center:

1. Choose a setting based on the item to be stored in the pan.

2. Push the button that corresponds to that setting.

3. The indicator light for that setting will illuminate to verify that

the pan is ready to be loaded.

Cold

I_g_ed en_ Ca e C_ter 6

Var)ous Cheeses •

Jams and Jellies

Fresh Produce• 0

Fresh Herbs O

Berry Fruits •

Meats 9

Beverages •

Colder

To remove and replace the ingredient care center cover:

1. Remove food from ingredient care center cover. Pull drawer

out about 4" (10.16 cm). Reach under the glass shelf with

both hands and lift gently upward until back of shelf is free.

Tilt shelf at an angle and remove shelf from refrigerator being

careful not to bump the glass.

2. Replace the cover by holding the glass shelf firmly with both

hands, tilt the shelf at an angle and position it above the

support rails. Place shelf gently on support rails on side wall.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and

moisture-proof. Rewrap if necessary. See the following chart for

storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ................. use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ........................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or

plastic containers with tight lids.

To remove and replace the crispers:

1. Slide the crisper drawer straight out to the stop. Lift the front

of the drawer with one hand while supporting the bottom of

the drawer with your other hand and slide the drawer out the

rest of the way.

2. To replace the crisper drawer, place the drawer onto slides

and push the drawer back until securely in position.

3. Carefully test the crisper drawer to make sure it has been

replaced properly.

To clean the crisper covers:

1. To clean the top crisper cover, remove the ingredient care

center located above it.

2. Toclean the bottom crisper cover, first remove the top crisper

drawer.

NOTE: For long-term storage, store eggs in a covered container

or in their original carton on an interior shelf,

To remove and replace the wine rack:

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the

wall of the refrigerator.

FREEZERFEATURES

To remove and replace the shelf:

1. Remove the shelf by lifting it up and pulling it straight out.

2. Replace the shelf by putting it over the supports and lowering

it into place.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food,

the type of packaging or wrap used (should be airtight and

moisture-proof), and the storage temperature. Ice crystals inside

a sealed package are normal. This simply means that moisture in

the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot

[907-1,350 g per 28 L] of freezer space). Leave enough space in

the freezer for air to circulate around packages. Be careful to

leave enough room for the door to close tightly.

For more information on preparing food for freezing, check a

freezer guide or reliable cookbook.

The freezer basket can be used to store bags of frozen fruits and

vegetables that may slide off freezer shelves.

To remove and replace the freezer basket:

1. Pull the basket straight out to the stop.

2. Lift the front of the basket and slide it out the rest of the way.

3. Replace the basket by positioning it on the side wall guide

rails. Lift the basket front slightly while pushing it past the

guide rail stops and slide basket in the rest of the way.

DOOR FEATURES REFRIGERATOR CARE

The utility compartment can be placed in any position on the

refrigerator door.

To remove and replace the utility bin:

1. Remove utility compartment by grasping both ends and lifting

compartment up and out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

Large door bins hold gallon containers and the smaller door bins

hold 2-liter bottles. The door bins are adjustable and removable

for easy cleaning and adjusting.

Gallon Door Bin

To install gallon door bin:

NOTE: The gallon door bin can only be placed on the lower

support.

1. Position gallon door bin above lowest door adjustment slot.

2. Push down to secure bin.

3. Adjust other bins, as necessary to allow for milk or beverage

container height.

Door Bins

To remove and replace the door bins:

1. Remove the bin by lifting it up and pulling it out.

2. Replace the bin by sliding it in above the desired support and

pushing it down until it stops.

Exp_osio_ Hazard

Use _onflammab_e c_eaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To clean your refrigerator:

1. Remove the top grille. See "Power On/Off Switch."

2. Press power switch to OFR

3. Remove all removable parts from inside, such as shelves,

crispers, etc.

4. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.

[26 g to .95 L] of water).

5. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water. Do

not use abrasive or harsh cleaners. Dry thoroughly with a soft

cloth. For additional protection against damage to painted

metal exteriors, apply appliance wax (or auto paste wax) with

a clean, soft cloth. Do not wax plastic parts.

NOTE: To keep your Stainless Steel refrigerator looking like

new and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel Cleaner

& Polish.

IMPORTANT: This cleaner is for Stainless Steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does

occur, clean plastic part with a sponge and mild detergent in

warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see "Accessories."

Clean the condenser coils located behind the top grille

ventilation panel regularly. Coils may need to be cleaned as

often as every other month. This may help save energy.

• Use a vacuum cleaner with an extended attachment to

clean the condenser coils when they are dusty or dirty.

Clean defrost pan using mild detergent in warm water. Dry

thoroughly.

• Remove the base grille by removing a screw at each end.

Dispenser Light (on some models)

Reach through the dispenser area to remove and replace light

bulb.

Remove the defrost pan by pushing up on the retaining

clip under the refrigerator while sliding the pan forward.

A.Dispenser Light

Refrigerator Control Panel Light

Style 1

Reach behind the refrigerator control panel to remove and

replace light bulb.

A. Defrost pan

B. Retaining clip

• Replace the defrost pan by positioning the edge of the

defrost pan approximately 7" (17.8 cm) from the left side

of the refrigerator. Lift defrost pan into guides and push

back and place pan inside of retaining clip. Replace the

base grille and base grille screws.

Press the power switch to the ON position.

Replace the top grille. See "Power On/Off Switch."

Style 2

Use a 1/4"hex-head screw driver to remove and replacethe light

shield.

Freezer and Crisper Lights

Remove the light shield by grasping the sides and squeezing

in toward the center. Once the side hooks of the shield are

free from the freezer or crisper lining, pull down the shield.

Replace the light shield by squeezing the top and bottom

toward the center and inserting the hooks into the slotted

holes. Once the hooks are in place, snap the front tab into the

slotted hole.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size and shape. The

dispenser light requires a heavy duty 10-watt bulb. All other lights

require a 40-watt maximum appliance bulb. Replacement bulbs

are available from your dealer or appliance store.

1. Remove the top grille. See "Power On/Off Switch."

2. Press the power switch to OFF.

3. Remove light shield when applicable as shown.

NOTE: To clean a light shield, wash it with warm water and a

liquid detergent. Rinse and dry the shield well.

4. Remove light bulb and replace with one of the same size,

shape and wattage.

5. Replace light shield when applicable as shown.

6. Press the power switch ON.

7. Replace the top grille. See "Power On/Off Switch."

If the power will be out for 24 hours or less, keep the door or

doors closed (depending on your model) to help food stay cold

and frozen.

If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen for

2 to 4 days.

• If neither afood locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled

one. A freezer full of meat stays cold longer than a freezer full of

baked goods. If you see that food contains ice crystals, it may be

refrozen, although the quality and flavor may be affected. If the

condition of the food is poor, dispose of it.

Your refrigerator is equipped with the Holiday Mode feature,

which is designed for the traveler who wishes to turn off the lights

and icemaker. By selecting this feature, the temperature set

points remain unchanged, the ice maker will be disabled and the

interior lights will turn off. For most efficient refrigerator operation,

it is recommended to exit the Holiday Mode when it is no longer

required.

If you choose to leave the refrigerator on while you're

away:

1. Use up any perishables and freeze other items.

2. Press HOLIDAY MODE pad.

3. If your refrigerator has an automatic ice maker, shut off water

supply to the ice maker.

4. Empty the ice bin.

5. When you return from vacation, press HOLIDAY MODE to

return to normal operation.

If you choose to turn the refrigerator off before you leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

3. Depending on your model, turn the Thermostat Control

(or Refrigerator Control) to OFR See "Using the Controls."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of

Your refrigerator will not operate

is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

Has a household fuse or circuit breaker tripped? Replace

the fuse or reset the circuit breaker.

Is the refrigerator or freezer control turned to the OFF

position? See "Using the Control(s)."

Is the refrigerator defrosting? Recheck to see if the

refrigerator is operating in 30 minutes. Your refrigerator will

regularly run an automatic defrost cycle.

is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See "Using

the Control(s)." If this does not correct the problem, call for

service.

The lights do not work

is the power supply cord unplugged? Plug into a grounded

3 prong outlet.

Is a light bulb loose in the socket or burned out? See

"Changing the Light Bulb(s)."

Has the door been open more than 10 minutes? When the

door is held open for more than 10 minutes, the "Door Open"

indicator light will flash and the interior lights will shut off. See

"Door Open" in "Using the Control(s)."

There is water in the defrost drain pan

• is the refrigerator defrosting? The water will evaporate. It is

normal for water to drip into the defrost pan.

• is it more humid than normal? When it is humid, expect that

the water in the defrost pan will take longer to evaporate.

The motor seems to run too much

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room

temperatures, expect your motor to run about 80% of the

time. Under warmer conditions, it will run even more.

an unnecessary service call.

Has a large amount of food just been added to the

refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the

refrigerator back down.

Are the doors opened often? The motor will run longer

when this occurs. Conserve energy by getting all items out at

one time, keeping food organized, and closing the door as

soon as possible.

Are the controls not set correctly for the surrounding

conditions? See "Using the Control(s)."

Are the doors not closed completely? Close the doors

firmly. If they do not close completely, see "The doors will not

close completely" later in this section.

Are the condenser coils dirty? This prevents air transfer and

makes the motor work harder. Clean the condenser coils.

Refer to the "Cleaning" section.

Are the door gaskets not sealed all the way around?

Contact a technician or other qualified person.

NOTE: Your new refrigerator will run longer than your old one

due to its high-efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normalforyourrefrigeraton See"Normal

Sounds."

The ice maker is not producing ice or not enough ice

• Has the ice maker just been installed? The ice bin holds

14 to 17 Ibs (6.4 to 7.7 kg) of ice. The ice bin can take three to

four days to completely fill, if no ice is used during this time.

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after ice maker hookup for ice production. See

"Using the Control(s)."

Is the ice maker wire shutoff arm in the OFF (arm up)

position (on some models)? Lower the wire shutoff arm to

the ON (arm down) position. See "Ice Maker and Storage

Bin."

• Is the ice maker switch in the OFF (right) position (on

some models)? Move ice maker switch to the ON (left)

position. See "Ice Maker and Storage Bin."

• Is the water line shutoff valve to the refrigerator turned

on? Turn on the water valve. See "Connect Water Line to

Refrigerator" in the Installation Instructions.

Does the ice maker mold have water in it or has no ice

been produced? Make sure your refrigerator has been

connected to a water supply and the supply shutoff valve is

turned on. See "Connect Water Line to Refrigerator" in the

Installation Instructions.

Is an ice cube jammed in the ice maker ejector arm?

For models with an interior ice bin, remove the ice from the

ejector arm with a plastic utensil. For models with an ice bin

located on the freezer door, access the ice maker by

depressing the ice sensor door on the upper left side of the

freezer interior. While depressing the sensor door, lift the ice

maker service door and remove the ice from the ejector with

a plastic utensil. See "Ice Maker and Storage Bin."

• Has a large amount of ice just been removed? Allow three

to four days for an empty ice bin to completely fill, if no ice is

used during this time.

• Are the controls set correctly? See "Using the Control(s)."

Is there a water filter installed on the refrigerator? The

filter may be clogged or installed incorrectly. Check the filter

installation instructions to ensure that the filter was installed

correctly and is not clogged. If installation or clogging is not a

problem, call a technician or other qualified person.

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

Off-taste, odor or gray color in the ice

• Are the plumbing connections new, causing discolored or

off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored too long? Throw old ice

away and make a new supply.

• Does the freezer and ice bin need to be cleaned? See

"Cleaning" or "Ice Maker and Storage Bin."

• Has food in the freezer or refrigerator been wrapped

properly? Use airtight, moisture-proof packaging to help

prevent odor transfer to stored food.

• Does the water contain minerals (such as sulfur)? A filter

may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration

system needs additional flushing. Run additional water

through the water dispenser to flush the water filtration

system more thoroughly (at least 2 to 3 gal. [8 to 12 L] or 6 to

7 minutes initially). Discard discolored ice.

The ice dispenser will not operate properly

• Is the freezer door closed completely? Push the door firmly

shut. If it will not shut all the way, see "The doors will not

close completely" later in this section.

Is the ice bin installed correctly? For models with an interior

ice bin, push the ice bin in all the way. Ifthe ice bin does not

go in all the way, it may not be put in straight. Pull it out and

try again. For models with an ice bin located on the freezer

door, the bin should sit level. To remove the bin, press the

release button on the right side of the bin and lift straight up.

Replace the bin in the door making sure it is properly aligned

and snapped securely into place. See "Ice Maker and

Storage Bin."

Has the wrong ice been added to the bin? Use only cubes

produced by the current ice maker. If other cubes have been

added, remove all cubes and check to see that none have

become stuck in the delivery chute.

• Has the ice frozen in the ice bin? Shake the ice bin to

separate cubes. If cubes do not separate, empty bin and wait

24 hours for ice to restock.

Has the ice melted around the auger (metal spiral) in the

ice bin? Dump the ice cubes and clean the ice bin

completely. Allow 24 hours for the ice maker to restock. Do

not try to remove the melted ice with a sharp object. You

could damage the ice bin.

• Is ice stuck in the delivery chute? Clear the ice from the

delivery chute with a plastic utensil. Do not use anything

sharp to remove the ice. You could cause damage.

Is the ice dispenser stalling while dispensing "crushed"

ice? Stop dispensing ice. Change the ice button from

"crushed" to "cubed." Depress the ice dispenser arm using a

sturdy glass. If cubed ice dispenses correctly, depress the

button for "crushed" ice and begin dispensing again. See

"Water and Ice Dispensers."

• Is there ice in the bin? See "The ice maker is not producing

ice" earlier in this section.

Has the dispenser arm been held in too long? Release

dispenser arm. Ice will stop dispensing when the arm is held

in too long. Wait three minutes for dispenser motor to reset

before using again. It is best to take large amounts of ice

directly from the ice bin, not through the dispenser.

Ice bin difficult to remove

Is the ice bin difficult to remove (on some models)? For

models with an ice bin located on the freezer door, select

"cubed" ice. Using a sturdy glass, quickly depress and

release the ice dispenser arm. Open the freezer door, depress

the release button on the ice bin and lift upward. See "Ice

Maker and Storage Bin."

The water dispenser will not operate properly

Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to

depress the water dispenser bar until the water begins to

flow. Flush the water system by dispensing and discarding

2 to 3 gal. (8 to 12 L) of water. Cleaning the system will take

approximately 6 to 7 minutes and will help clear air from the

line. Additional flushing may be required in some households.

See "Water and Ice Dispensers."

Is the water shutoff valve not turned on or the water line

connected at the source? Make sure the water shutoff valve

is turned on and the water source is connected to the

refrigerator. See "Connect Water Line to Refrigerator" in the

Installation Instructions.

Is the water shutoff valve clogged or incorrectly installed?

See "Connect Water Line to Refrigerator" in the Installation

Instructions. If clogging or installation is not a problem, call

for service or contact a plumber.

Is there a kink in the home water source line? If you find or

suspect a kink in the water line, call for service.

Is there a water filter installed on the refrigerator? The

filter may be clogged or incorrectly installed. First, check the

filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call for service.

Water or ice is leaking from the dispenser

Is the glass not being held under the ice dispenser long

enough, causing the ice to spill? Hold the container under

the ice chute for two to three seconds after releasing the

dispenser lever. Water or ice may continue to dispense during

this time.

• Is an ice cube stuck in the chute and holding the trap

door open? Remove the cube.

Is there a water filter installed on the refrigerator? The

water filtration system may have air in the lines, causing water

to drip. Additional flushing may help clear air from the lines.

Normal dispenser use should flush air from the lines within 24

to 72 hours.

Water flow from the dispenser decreases noticeably

Is there a water filter installed on the refrigerator?

The filter may be full or incorrectly installed. Remove the

water filter cartridge. See "Water Filtration System." Operate

the dispenser. If the water flow increases noticeably, replace

the filter.

The dispenser water is not cool enough

• Has the refrigerator been newly installed? Allow 24 hours

for the refrigerator to cool completely.

• Has a large amount of water been recently dispensed?

Allow 24 hours for the water to cool completely.

• Has water not been recently dispensed? The first glass of

water may not be cool. Discard the first glass of water.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the

automatic exterior moisture control. If still concerned, call for

service.

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the

refrigerator. Remove any objects from in front of the air vents.

See "Ensuring Proper Air Circulation" for the location of air

vents.

Are the door(s) opened often? The refrigerator will warm

when this occurs. Keep the refrigerator cool by getting all

items out at one time, keeping food organized, and closing

the door as soon as possible.

Has a large amount of food just been added to the

refrigerator or freezer? Adding a large amount of food

warms the refrigerator. It can take several hours for the

refrigerator to return to the normal temperature.

Are the controls set correctly for the surrounding

conditions? See "Using the Control(s)."

Is the refrigerator not cooling? For models with digital

controls, turn the unit OFF then ON again to reset. See "Using

the Control(s)." If this does not correct the problem, call for

service.

There is interior moisture buildup

• Are the air vents blocked in the refrigerator? Remove any

objects from in front of the air vents. See "Ensuring Proper Air

Circulation" for the location of air vents.

Are the door(s) opened often? Avoid humidity buildup by

getting all items out at one time, keeping food organized, and

closing the door as soon as possible.

Is the room humid? It is normal for moisture to build up

inside the refrigerator when the room air is humid.

Is the food packaged correctly? Check that all food is

securely wrapped. Wipe off damp food containers before

placing in the refrigerator.

Are the controls set correctly for the surrounding

conditions? See "Using the Control(s)."

Was a self-defrost cycle completed? It is normal for

droplets to form after the refrigerator self-defrosts.

The doors will not close completely

• Are food packages blocking the door open? Rearrange

containers so that they fit more tightly and take up less

space.

Is the ice bin out of position? For models with an interior ice

bin, push the ice bin in all the way. If the ice bin does not go in

all the way, it may not be put in straight. Pull it out and try

again. For models with an ice bin located on the freezer door,

the bin should sit level. To remove the bin, press the release

button on the right side of the bin and lift straight up. Replace

the bin in the door making sure it is properly aligned and

snapped securely into place. See "Ice Maker and Storage

Bin."

Are the pans, shelves, bins, or baskets out of position?

Put the crisper cover and all pans, shelves, bins, and baskets

back into their correct positions. See "Crisper Drawers and

Covers" for more information.

• Are the gaskets sticking? Clean gaskets according to the

directions in "Cleaning."

• Does the refrigerator wobble or seem unstable? Level the

refrigerator. See "Adjust Doors" and "Level Refrigerator" in

the Installation Instructions.

The doors are difficult to open

• Are the gaskets dirty or sticky? Clean gaskets according to

the directions in "Cleaning."

ASSISTANCE OR SERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

only use factory specified replacement parts. Factory specified

replacement parts will fit right and work right because they are

made with the same precision used to build every new

KITCH ENAID®appliance.

To locate factory specified replacement parts in your area, call

our Customer Interaction Center telephone number or your

nearest designated service center.

Call the KitchenAid Customer Interaction Center

toll free: 1-800-422-1230.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

• Referrals to local dealers, repair parts distributors, and

service companies. KitchenAid designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in the United States.

To locate the KitchenAid designated service company in your

area, you can also look in your telephone directory Yellow

Pages.

For further assistance

If you need further assistance, you can write to KitchenAid with

any questions or concerns at:

KitchenAid Brand Home Appliances

Customer Interaction Center

553 Benson Road

Benton Harbor, M149022-2692

Please include a daytime phone number in your correspondence.

Call the KitchenAid Canada Customer Interaction Center toll free:

1-800-461-5681 Monday to Friday 8:00 a.m. - 6:00 p.m. (EST).

Saturday 8:30 a.m. - 4:30 p.m. (EST).

Our consultants provide assistance with:

• Features and specifications on our full line of appliances.

• Referrals to local dealers.

For service in Canada

Call 1-800-807-6777. KitchenAid Canada designated service

technicians are trained to fulfill the product warranty and provide

after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to KitchenAid

Canada with any questions or concerns at:

KitchenAid Canada

Customer Interaction Center

1901 Minnesota Court

Mississauga, Ontario L5N 3A7

Please include a daytime phone number in your correspondence.

To order accessories, call 1-800-442-9991 and ask for the

appropriate part number listed below or contact your authorized

KitchenAid dealer. In Canada, call 1-800-807-6777.

Stainless Steel Cleaner & Polish

Order Part #8171420

Base grille water filter cartridge:

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before

or after the system. Systems certified for cyst reduction may

be used on disinfected waters that may contain filterable

cysts.

Standard Cartridge:

Order Part #4396548 (LC 400V)

WATER FILTER

CERTIFICATIONS

Slate of Calilorma

Deparlmcnl of Health Service,

WaterTreatment Device

CertificateNumber

03 - 1551

Daw Issued iamla_y ?l, 2003

Trademark/Mndel Designation Replacement Element_ Ruled Ca_

Wlmlpool WF-NIX'240V NLC240V 240 ga]

Whtr/pool WI -t Ca{RW c_o_ 41_) gal

Manufacturer: ..... _x_at Cotp

_le water treatment devlcets) Hs_ed *_n this certificate have met the testillg requirements pursuant to Section

116830 of the Health and Salet_ _Code for the follo_in_ hoafih related eontalainant_

Microbiological Contantinaut_ and Turbidity |n or _ani_iRadfolo_ieal Contaminant_

Cyst_

1 _rbldlb

Organic Contaminants

_\tt_ ne

24-D

Ben/xme

p-mcmom_nz ¸- :

Toxaphene

r_t_d Servlre FIm_: 05gpm

DO not use where water is microbfo fogical|y unsafe or _ith water of unknown quality, except that systems

certified for cyst reduction may be used on disinfected waters that may contain fifier aMe cysts.

PRODUCT DATA SHEETS

Base Grille Water Filtration System

Model WF-LC400V/LC400V Capacity 400 Gallons (1514 Liters)

Tested and certified by NSF International against ANSI/NSF Standard

42 for the reduction of Chlorine Taste and Odor, Particulate Class I*;

and against ANSI/NSF Standard 53 for the reduction of Lead,

Mercury, Atrazine, Benzene, Toxaphene, p-dichlorobenzene, 2, 4-D,

Cysts, Turbidity and Asbestos.

This system has been tested according to ANSl/NSF 42/53 for the reduction of the substances listed below. The concentration of

the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for

water leaving the system, as specified in ANSI/NSF 42/53.

Substance Reduction NSF Average Influent Challenge Maximum Average Minimum % Average % NSFTest

Aesthetic Effects Reduction Influent Concentration Effluent Effluent Reduction Reduction Number

Requirements

Chlorine Taste/Odor ->50% 2.1 mg/L 2.0 mg/L _+10% 0.06 mg/L 0.05 mg/L 97.1% 97.6% 507173-02

Particulate Class 1" _>85% 5,366,667/mL 2,300/mL 99.9%

At least 10,000 4,100/mL** 99.3% 507175-02

particles/mL

Contaminant NSF Average Influent Challenge Maximum Average Minimum % Average % NSFTest

Reduction Reduction Influent Concentration Effluent Effluent Reduction Reduction Number

Requirements

Lead: @pH 6.5 0.01mg/L 0.16 rag/L1- 0.15 mg/L _+10% 0.001 mg/L 0.001 mg/L 99.3% 99.35% 507601-01

Lead: @pH 8.5 0.01mg/L 0.15 rag/L1- 0.15 mg/L _+10% 0.001 mg/L 0.001 mg/L 99.2% 99.31% 507602-01

Mercury: @ pH 6.5 0.002 mg/L 0.0061 mg/L 0.006 mg/L_+ 10% 0.0004 mg/L 0.0003 mg/L 93.5% 96.7% 507603-02

Mercury: @ pH 8.5 0.002 mg/L 0.0057 mg/L 0.006 mg/L_+ 10% 0.0008 mg/L 0.00051 mg/L 85.8% 91.2% 507604-02

Benzene 0.005 mg/L 0.0138 mg/L 0.015 _+10% 0.0005 mg/L 0.005 mg/L 96.3% 96.3% 507183-02

p-dichlorobenzene 0.075 mg/L 0.220 mg/L 0.225 _+10% 0.0005 mg/L 0.0005 mg/L 99.7% 99.7% 507186-02

Toxaphene 0.003 mg/L 0.014 mg/L 0.015 _+10% 0.0014 mg/L 0.001 mg/L 90% 92.96% 507185-02

Atrazine 0.003 mg/L 0.009 mg/L 0.009 mg/L +_10% 0.0013 mg/L 0.00036 mg/L 85.6% 85.6% 507181-02

2, 4-D 0.07 mg/L 0.197 mg/L 0.215 _+10% 0.058 mg/L 0.0137 mg/L 70.6% 93.06% 507180-02

Asbestos 99% 26 x 107 107to 10_fibers/Ll-1 - 0.18 x 107mg/L 0.18 x 107mg/L 99.93 99.93% 507178-02

Cysts:[: 99.95% 111,000/mL 50,000/L min. 1 mg/L 1 mg/L 99.99% 99.99% 507187-02

Turbidity 0.5 NTU 11.08 NTU 11 _+1 NTU 0.13 NTU 0.078 NTU 98.8% 99.3% 507751-02

Test Parameters: pH = 7.5 + 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 63°F

(17.2°C).

• It is essential that operational, maintenance, and filter

replacement requirements be carried out for the product to

perform as advertised.

• Model WF-LC4OOV The filter monitor system measures the

amount of water that passes through the filter and alerts you

to replace the filter. When 90% of the filter's rated life is used,

the filter indicator light changes from green to yellow. When

100% of the filter's rated life is used, the filter indicator light

changes from yellow to red, and it is recommended that you

replace the filter. Use replacement cartridge LC4OOV,part

#4396548. 2004 suggested retail price of $39.99 U.S.A./

$59.95 Canada. Prices are subject to change without notice.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system. Systems certified for cyst reduction may be used

on disinfected waters that may contain filterable cysts.

• Refer to the front cover or "Accessories" section for the

Manufacturer's name, address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited

warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well

Water Pressure 30 - 120 psi (207 - 827 kPa)

Water Temperature 33 ° - 100°F (0.6 ° -37.8 ° C)

Service Flow Rate 0.5 GPM (1.89 L/min.) @ 60 psi.

*Class I particle size: >0.5 to <1 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

1,These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

1-1-Fibers greater than 10 um in length

:l:Based on the use of Cryptosporidium parvum oocysts

®) NSF is a registered trademark of NSF International.

KITCHENAID ®BUILT-IN REFRIGERATOR WARRANTY

TWO-YEAR FULL WARRANTY

For two years from the date of purchase, when this refrigerator (excluding the water filter cartridges) is operated and maintained

according to instructions attached to or furnished with the product, KitchenAid will pay for factory specified replacement parts and

repair labor costs to correct defects in materials or workmanship. Service must be provided by a KitchenAid designated service

company.

Water filter cartridge: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated and

maintained according to instructions attached to or furnished with the product, KitchenAid will pay for replacement parts to correct

defects in materials and workmanship.

THIRD THROUGH SIXTH YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM PARTS AS LISTED

In the third through sixth years from the date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with the product, KitchenAid will pay for factory specified replacement parts and repair labor costs to correct

defects in materials or workmanship in the sealed refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and

connecting tubing. Service must be performed by a KitchenAid designated service company.

SEVENTH THROUGH TWELFTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM

In the seventh through twelfth years from date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with the product, KitchenAid will pay for factory specified replacement parts to correct defects in materials or

workmanship in the sealed refrigeration system. These parts are: compressor, evaporator, condenser, dryer, and connecting tubing.

LIFETIME LIMITED WARRANTY ON DOOR BINS

For the life of the product, when this refrigerator is operated and maintained according to instructions attached to or furnished with the

product, KitchenAid will replace all Door Bins due to defective materials or workmanship.

KitchenAid will not pay for:

1. Service calls to correct the installation of your refrigerator, to instruct you how to use your refrigerator, to replace house fuses or

correct house wiring or plumbing, to replace light bulbs, or to replace water filters other than as noted above.

2. Repairs when your refrigerator is used in other than normal, single-family household use.

3. Pickup and delivery. Your refrigerator is designed to be repaired in the home.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, improper installation, acts of God, or use of products not

approved by KitchenAid or KitchenAid Canada.

5. Any food or medicine loss due to product failure.

6. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

7. Removal and replacement of trim or decorative panels that interfere with servicing the product.

8. Labor or parts installed by any non-designated service company during the full warranty period, unless approved by KitchenAid

before service is performed.

g. In Canada, travel or transportation expenses for customers who reside in remote areas.

10. Any labor costs during the limited warranty periods.

KITCHENAID AND KITCHENAID CANADA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states or provinces do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or

province to province.

Outside the 50 United States and Canada, a different warranty may apply. Contact your authorized KitchenAid dealer to

determine if another warranty applies.

If you need service, first see the "Troubleshooting" section of this book. After checking "Troubleshooting," additional help can be found

by checking the "Assistance or Service" section or by calling the KitchenAid Customer Interaction Center, 1-800-422-1230 (toll-free),

from anywhere in the U.S.A. In Canada, contact your designated KitchenAid Canada service company or

call 1-800-807-6777. 5/03

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your refrigerator to

better help you obtain assistance or service if you ever need it.

You will need to know your complete model number and serial

number. You can find this information on the model and serial

number label located on the inside wall of the refrigerator

compartment.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

La page charge ...

KitchenAid KSSO36QMB02 Le manuel du propriétaire

Marque: KitchenAid

Modèle: KSSO36QMB02

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: KitchenAid KSSO36QMB02 Owner's manual
español: KitchenAid KSSO36QMB02 El manual del propietario

KitchenAid KSSO36QMB02 Le manuel du propriétaire

KitchenAid KSSO36QMB02 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents