Sensear SmartPlug Manuel utilisateur

smartPlug

USER GUIDE

1

English

GETTING STARTED

1. Headset anatomy

2. Wearing the headset

3. Fitting the Earbuds

4. Charging the headset

5. Power up the headset

6. Environmental modes

7. Connecting A Two Way

Radio

8. Using Bluetooth

9. Bluetooth pairing and

connecting

10. Using Short Range

11. Using FM Radio

12. Troubleshooting

1. HEADSET ANATOMY

Right indicator light

Right Ear Bud

Disposable Foam Tip

Left Ear Bud

Inline PTT

Inline 1 Button

Inline 2 Button

Left Indicator Light

Power Button

Volume Up Button

Multi Function Button

Volume Down Button

Main Unit with Belt Clip

Two-Way Radio Connection

Mini USB Connection

Battery Rechaging Connection

1

English

3

2

2.WEARING THE HEADSET

The smartPlug is a state of the art hearing protection

communication system that allows you to retain situational

awareness while being in full contact with all your

communication devices.

Situational awareness is provided by processing

technology and environmental microphones within the

Earbuds.

Contact through other communication devices is enabled by:

- Two Way Radios interface cables (sold separately).

- Bluetooth to Two Way Radios and cell phones (if installed)

- Direct Headset to Headset communications through

Short Range (if installed)

The smartPlug is designed to be worn with the main housing

attaching to the belt or pant seam, and the Inline PTT

attaching to the shirt / upper garment of the user.

Note: For SR communications, the best communication

range is achieved with the Inline PTT set as high up on the

user as possible.

Ear

Microphone

Ear Buds

Inline PTT

Main Housing

Earbud

Foam Tip

In-Ear speaker

and microphone

English

3

2

3. FITTING THE EARBUDS

1. Place Disposable Foam

Tip between thumb and

forefinger.

6. Using your opposite hand, pull

your ear upward and outward.

Insert the Ear Bud deeply into the

ear -as you would normally do with

a Foam Ear Plug.

7. Hold the Ear Bud in place for

30 seconds while the Foam Tip

expands.

8. Check to ensure the Ear Buds

are correctly inserted.

9. A poor fit will be visible by the

Earbuds being far away from the

ear. No foam tip should be visible.

Repeat the process until a good

fit is achieved.

2. Roll Foam Tip to a

compressed, crease free

cylinder

3. Push the Foam Tip all the

way onto the Ear Bud spout.

4. Roll the Foam Tip again

between the thumb and

forefinger.

5. Ensure the Foam Tip

remains a compressed,

crease free cylinder on the

Ear Bud.

It is critical the earbuds are correctly fitted to ensure the correct level of hearing protection and communication abilities. The Earbuds

incorporate an in-ear pickup, if the Earbuds are not fitted correctly, the speech quality may be lower than expected.

English

5

4

4. CHARGING

Your headset comes supplier with a charger. Do not

attempt to use third party chargers as damage may

result.

The headset should be regularly charged. To charge

your headset connect the charger to the headset and

connect to the mains power.

While charging the Right Indicator LED will be Red.

When charging is complete the LED will turn Green.

Note: Be sure to charge your headset fully before first

use.

Note: Your headset will automatically power up when the

charger is connected to the headset.

Charge Time :5 hours

Battery Life: 15 hours

Your headset is powered by a built-in high capacity Lithium Ion battery.

Thisis designed to last the life of your headset and should be returned to

the manufacturer for replacement and servicing. Any attempt to access

the battery will damage the headset. Please see accompanying smartPlug

Headset Information guide for additional safety battery precautions.

Right Indicator

Red: Charging

Green: Charge Complete

Charger

Charging Jack

English

5

4

5. POWER ON HEADSET

Your headset must be powered up to use

situational awareness and the communication

connectivity features.

Power on / off

To power up your headset press and release the

power button.

To power off your headset press and hold the power

button until the unit powers off.

6. ENVIRONMENTAL MODES

Your smartPlug headset features situational

awareness technology.

(Speech Enhancement, Noise Suppression)

allows you to be in audible contact with your

surroundings while wearing your headset.

To toggle situational awareness on or off

momentarily press and release the power button.

Right Indicator

Green fast flash: Quiet Mode

Green slow flash:

active

Red flash:

Battery low (less than 1 hour)

Off: Headset off

Power Button

English

7. CONNECTING TWO WAY RADIO

smartPlugheadset can be connected to most Two Way

Radios through interface cables (sold separately).

1. Connect the Two Way Radio Cable into the Two way

Radio Connector located on the bottom of the Main

Unit.

2. Turn the Two Way Radio on. A tone will be heard

through the headset indicating it has detected the

Two Way Radio.

3. Adjust the volume of the Two Way Radio

communication by the normal controls of your Two

Way Radio until a comfortable level is reached.

4. To transmit, press and hold the Inline 1 Button or

the button programmed by your dealer.

Note: See ‘Using Bluetooth’ for more information on

connecting Two-Way Radios by Bluetooth.

Two Way Radio Connector

Two Way Radio Cable

Inline PTT

Inline 1 Button

7

6

English

8. USING BLUETOOTH

smartPlug Headsets also feature Bluetooth connectivity

(if installed). Bluetooth enables wireless connections to some

models of Two Way Radio, industrial computers, vibration analysers

and most Cell phones. If Bluetooth is installed on your smartPlug,

the following details apply.

Default automatic connection setting: When the headset powers

up, the smartPlug searches for previously paired devices. If a

previously paired device is within range, it will automatically attempt

to reconnect to this device. A blue light will flash slowly if a Bluetooth

connection is made and you will hear a tone in the headset.

Note: When entering pairing mode the smartPlug forgets all

previously connected devices.

Note: Bluetooth is discoverable for 2 minutes in pairing mode. If no

connection has been made within this time, the process will need to

be repeated.

Bluetooth Phone :To answer calls, press the Multi Function Button

(or programmed button, consult your dealer). To end or reject a

call, press and hold the Multi Function button for 2 seconds.

Bluetooth PTT:Some radios and cell phones feature PTT over

Bluetooth. Please consult your dealer for more information.

7

6

English

9

8

9. BLUETOOTH PAIRING AND

CONNECTING

Bluetooth pairing to new device:

For Bluetooth functionality, the smartPlug headset must be paired

and connected.

1. Enable Bluetooth on the device which you want to connect to the

smartPlug

2. Power up the smartPlug

3. Hold the Multi Function Button for 5 seconds to enable pairing.

A blue light indicator will switch on.

4. Follow pairing instructions on the device that you want to

connect to, search and pair the smartPlug. If asked for a

passkey, enter 0000

5. Once paired, the headset will automatically connect and the blue

light indicator will flash slowly.

6. If automatic connection fails, use the device instructions to

connect to the smartPlugheadset.

Multi Function Button

9

8

10. USING SHORT RANGE

Short Range (SR) is a technology enabling communication directly

between compatible smartPlug headsets. Short Range units tuned

to the same channel and within range will hear your transmissions.

SR behaves similarly to Two-Way Radios, where only one unit can

transmit at one time.

If Short Range is installed on your smartPlug, the following applies:

By default, Short Range is disabled and must be enabled. To

enable Short Range press Volume Up and Volume Down buttons

simultaneously, the smartPlug headset will make a tone indicating

SR has been enabled.

Headset to Headset Communication with SR: To communicate

with other smartPlug headsets push and hold the Inline 2 Button

and talk. Other headsets within range and tuned to the same

frequency will hear your transmissions.

SR Change frequency channel: To change SR channel up press

and hold Volume Up. To change SR channel down press and hold

Volume Down. The smartPlug headset will speak the channel

number. Up to 8 channels can be programmed.

The SR frequency can only be set by your dealer. Please contact

your dealer for reprogramming of channels.

Volume Up Button

Volume Down Button

Inline 2 Button

English

10

11. USING FM RADIO

SmartPlugheadsets can also be configured to receive FM radio

stations. This enables you to listen to FM radio while wearing

the smartPlug. If FM Radio is installed on your smartPlug, the

following applies:

By default, FM Radio Reception is disabled and must be enabled

as follows:

FM Radio on / off: Press the Power Button + Multi Function

Button together simultaneously. The smartPlugwill make a tone

indicating that FM radio has been enabled and you will hear the

currently tuned radio station in the headset.

To change radio stations, scan for a new station:

FM Radio Scan: Press and hold the Volume Up button for 2

seconds to scan up, or press and hold the Volume Down button

for 2 seconds to scan down. The smartPlugheadset will tune to

the next stations

Note: SR and FM radio cannot be enabled simultaneously. Enabling FM

radio will automatically disable SR Radio and vice versa.

Multi Function Button

Power Button

Volume Up Button

Volume Down Button

11

10

12. TROUBLESHOOTING

Having Trouble pairing the headset

Make sure any previously paired devices are powered off. Make

sure the radio is configured with Bluetooth enabled.

Headset and Radio will not connect

Wired:

Make sure the cable is securely fastened to both the Two Way

Radio and the Main Housing.

Bluetooth:

Make sure your radio and headset are paired together and within

range. Try pairing the two devices together again. Make sure the

Two Way Radio is not connected to another device or headset.

Having Trouble Hearing

Check your headset is on. Make sure your radio and headset

are paired, connected and within range. Check the radio’s LED

indicator to check transmit/receive is not stuck on. Check

your radio is functioning by turning off the headset and listening

through the radio. If the radio is working, try turning up the

volume control on the headset and on the radio controls.

Having trouble being heard

Check the headset is on. Make sure the radio and headset

are paired, connected and within range. Check your radio is

functioning by turning off the headset and talking through the

radio.Make sure you have fitted the Ear Buds correctly.

Ensure radio gain is set to a reasonable level.

Two-Way Radio distorted

Check your Two-Way Radio volume level. If the volume

is set too high, this may be breaching the volume level

on the smartPlug and affecting the sound quality.

English

11

Light Indicator Headset Function

Red On Charging

Green on Charge Complete

Red slow flash Battery Low <1hr remains

Green fast flash Quiet mode

Green slow flash

situational

awareness active

Blue on Bluetooth on and

discoverable

Blue slow flash Bluetooth connected

Blue fast flash Bluetooth incoming call

DOC00071 - Rev.00

smartPlug

GUÍA DEL USUARIO

Español

12

13

Español

PRIMEROS PASOS

1. Anatomía de los

auriculares

2. Uso de los auriculares

3. Montaje de los audífonos

4. Carga de los auriculares

5. Encendido de los

auriculares

6. Modalidad ambiental

7. Conexión de radio

bidireccional

8. Uso de Bluetooth

9. Asociación y conexión

por Bluetooth

10. Uso de corto alcance

(Short Range en inglés)

11. Uso de radio FM

12. Solución de problemas

1. ANATOMÍA DE LOS AURICULARES

Luz de indicador derecho

Audífono derecho

Protector de

espuma descartable

Audífono izquierdo

Línea PTT

Botón de linea 1

Botón de linea 2

Luz de indicador izquierdo

Botón de encendido

Botón para subir volumen

Botón multifunción

Botón para bajar volumen

Unidad principal con

sujetador para cinturón

Conexión de radio bidireccional

Mini conexión USB

Conexión para recarga

de batería

12

13

15

14

2. USO DE LOS AURICULARES

El smartPlug es un sistema de comunicación de protección

auditiva de última generación que le permite conservar la

conciencia situacional y simultáneamente mantener pleno

contacto con todos sus dispositivos de comunicación.

La conciencia situacional es proporcionada

por el procesamiento de la tecnología y los micrófonos

ambientales dentro de los audífonos.

El contacto a través de otros dispositivos de comunicación

se activa por medio de:

- Cables de interfaz de radio bidireccional (se venden por

separado).

- Bluetooth para radios bidireccionales y teléfonos

celulares (si están instalados).

- Comunicación directa de auricular a auricular a través

del sistema de corto alcance (si está instalado).

El smartPlug está diseñado para uso con la carcasa

principal sujeta al cinturón o a la costura del pantalón, y la

línea PTT sujeta a la camisa / prenda superior del usuario.

Nota: Para las comunicaciones de corto alcance, la mejor

cobertura de comunicación se logra con la línea PTT

colocada lo más elevada posible en el usuario.

Oído

MIcrófono

Audífonos

Línea PTT

Carcasa principal

Audífono

Protector de espuma

Auricular

dentro del oído

y micrófono

Español

15

14

Protector de espuma

3. MONTAJE DE LOS AUDÍFONOS

1. Coloque el protector de

espuma desechable entre

el pulgar y el índice.

6. Con la mano opuesta, tire

de la oreja hacia arriba y hacia

afuera. Inserte el audífono

profundamente en el oído - como

lo haría normalmente con un

tapón de oídos.

7. Sostenga el audífono en su sitio

por 30 segundos mientras se

expande el protector de espuma.

8. Compruebe que los audífonos

se inserten correctamente.

9. Un mal ajuste se Observação

porque los audífonos quedan

lejos de la oreja. Ningún protector

de espuma debe quedar visible.

Repita el proceso hasta lograr

un buen ajuste.

2. Enrolle el protector de

espuma hasta formar un

cilindro comprimido libre de

pliegues.

3. Empuje el protector de

espuma hacia el pitorro del

audífono.

4. Enrolle el protector de

espuma otra vez entre el

pulgar y el índice.

5. Compruebe que el

protector de espuma

siga siendo un cilindro

comprimido libre de

arrugas en el audífono.

Es fundamental que los audífonos estén correctamente colocados para asegurar el nivel correcto de protección auditiva y capacidad de

comunicación. Los audífonos incorporan la recepción dentro del oído. Si los audífonos no se montan correctamente, la calidad de la voz puede

ser menor de lo esperado.

Español

17

16

4. CARGA

El auricular viene con un cargador. No intente utilizar

cargadores de terceros, pues podría provocar daños.

El auricular debe cargarse regularmente. Para cargar

el auricular, conecte el cargador al auricular y a la red

eléctrica.

Mientras carga, el indicador LED derecho está rojo.

Cuando finaliza la carga, el LED se pone verde.

Nota: Asegúrese de cargar el auricular completamente

antes del primer uso.

Nota: El auricular se encenderá automáticamente

cuando el cargador esté conectado al auricular.

Tiempo de carga: 5 horas

Duración de la batería: 15 horas

El auricular es alimentado por una batería de iones de litio de alta

capacidad incorporada. Está diseñada para durar toda la vida del auricular

y debe ser devuelta al fabricante para sustitución y mantenimiento.

Cualquier intento de acceder a la batería dañará el auricular. Consulte la

guía informativa de los auriculares smartPlug adjunta para adicionales

precauciones de seguridad de la batería.

Cargador

Conector de

carga

Español

Indicador derecho

Rojo: Cargando

Verde: Carga completa

17

16

El auricular debe estar encendido para usar las

funciones de conciencia situacional y de

conectividad de comunicación.

Encendido (on) / Apagado (off)

Para encender el auricular, presione y suelte el

botón de encendido.

Para apagar el auricular, presione el botón de

encendido y manténgalo presionado hasta que se

apague la unidad.

6. MODALIDAD AMBIENTAL

El auricular smartPlug utiliza la tecnología

de conciencia situacional (Speech

Enhancement, Noise Suppression: mejora del habla

y supresión de ruidos).

le permite estar en contacto auditivo con el

entorno mientras escucha los auriculares.

Para apagar o encender la conciencia situacional

presione un momento y suelte el botón

de encendido.

Indicador derecho

Parpadeo verde rápido: Modo silencioso

Parpadeo verde lento:

activo

Parpadeo rojo:

Batería baja

(menos de 1 hora)

Off: Auriculares apagados

Botón de

encendido

Español

5. ENCENDIDO DE LOS AURICULARES

El auricular smartPlug se puede conectar a la mayoría

de los radios bidireccionales a través de los cables de

interfaz (se venden por separado).

1. Conecte el cable del radio bidireccional al conector

de radio bidireccional situado en la parte inferior de

la unidad principal.

2. Encienda el radio bidireccional. Escuchará un tono

por el auricular que indica que éste ha detectado el

radio bidireccional.

3. Ajuste el volumen de la comunicación del radio

bidireccional por los controles normales de su radio

hasta alcanzar un nivel cómodo.

4. Para transmitir, mantenga presionado el botón de

línea 1 o el botón programado por el distribuidor.

Nota: Vea ‘Uso de Bluetooth’ para mayor información

sobre cómo conectar un radio bidireccional por

Bluetooth.

Conector de radio

bidireccional

Cable de radio bidireccional

Línea PTT

Botón

de línea 1

19

18

Español Español

7. CONEXIÓN DE RADIO BIDIRECCIONAL

La page est en cours de chargement...

Sensear SmartPlug Manuel utilisateur

Sensear SmartPlug Manuel utilisateur

dans d''autres langues

Autres documents