Tripp Lite BC800U Le manuel du propriétaire

Marque: Tripp Lite

Modèle: BC800U

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

UPS Systems

Models:

BC800U, INTERNET750U, INTERNET900U

(Series Numbers: AG-0314, AG-0317, AG-0390)

Owner’s Manual

Español 14 • Français 26

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

WARRANTY REGISTRATION

automatically entered to win an ISOBAR®

surge protector in our monthly drawing!

tripplite.com/warranty

21-10-016-93388E.indb 121-10-016-93388E.indb 1 10/15/2021 2:55:43 PM10/15/2021 2:55:43 PM

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of this product. Failure to heed these warnings

may affect the warranty.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust

or direct sunlight.

• For best performance, keep the indoor temperature between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

• Optional mounting: The UPS may be securely mounted in a horizontal or vertical position.

To mount, use two screws (not provided) to secure the UPS rear keyholes to a ﬂat surface.

UPS Connection Warnings

• Connect your UPS directly to a properly-grounded AC power outlet. Do not plug the UPS into

itself; this will damage the UPS.

• Do not modify the UPS plug and do not use an adapter that would eliminate the UPS

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must provide

clean, ﬁltered, computer-grade output.

• The mains socket outlet that supplies the UPS should be easily accessible and located near

the UPS.

Equipment Connection Warnings

Install in accordance with National Electrical Code standards ANSI/NFPA

70 and Canadian Electrical Code, Part I, C22.1.

Short-circuit backup protection and overcurrent protection is provided by

the building installation.

To reduce the risk of ﬁre, connect only to a circuit with a maximum 20A

provided branch circuit overcurrent protection in accordance with the

National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code,

Part I, C22.1. The plug on the power supply cord is intended to serve as

the disconnect device. Be sure that the socket-outlet is installed near the

equipment and is made easily accessible.

The UPS is intended for use on a TN power distribution system.

Important Safety Instructions

21-10-016-93388E.indb 221-10-016-93388E.indb 2 10/15/2021 2:55:43 PM10/15/2021 2:55:43 PM

Important Safety Instructions

Main relay

Breaker

I/P Filter

DC-AC

Inverter

DC-DC

Converter

AC-DC

Charger

O/P relay

IP-L O/P-L

IP-N O/P-N

IP/G O/P-G

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended.

• Do not connect surge protectors or extension cords to the output of your UPS. This might

damage the UPS and may affect the surge protector and UPS warranties.

• Connect the UPS to an outlet that is adequately protected against excess currents, short

circuits and earth faults as part of the building installation.

21-10-016-93388E.indb 321-10-016-93388E.indb 3 10/15/2021 2:55:43 PM10/15/2021 2:55:43 PM

Important Safety Instructions

Explanation of Symbols

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe proper precautions. Do not dispose of the batteries in a ﬁre. Do not open the UPS

or batteries. Do not short or bridge the battery terminals with any object. Unplug and turn

off the UPS before performing battery replacement. Use tools with insulated handles. There

are no user-serviceable parts inside the UPS. Battery replacement should be performed

only by authorized service personnel using the same number and type of batteries (Sealed

Lead-Acid). The batteries are recyclable. Refer to your local codes for disposal requirements

or visit tripplite.com/support/recycling-program for recycling information. Tripp Lite offers a

complete line of UPS System Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the

Web at tripplite.com/products/battery-ﬁnder/ to locate the speciﬁc replacement battery for

your UPS.

CAUTION: A battery can present a risk of electrical shock and high short-

circuit current. Contact with any part of a grounded battery can result in

electrical shock. The following precautions should be observed when working

on batteries:

• Remove watches, rings or other metal objects.

• Use tools with insulated handles.

• Wear rubber gloves and boots.

• Do not lay tools or metal parts on top of batteries.

• Disconnect charging source and load prior to installing or maintaining the battery.

• Unplug the UPS from the AC mains receptacle. Disconnect all cables, including the

equipment plugged into the UPS.

UPS and Battery Recycling

Tripp Lite products use sealed lead-acid batteries, which are highly recyclable.

Call Tripp Lite at 1.773.869.1234 or visit tripplite.com/support/recycling-program

for more information on recycling the batteries or any other Tripp Lite product.

Please refer to local codes for disposal requirements.

Caution Alternating

Current

Surge

Protected

Battery

Mode

Recyclable –

Contains Lead

21-10-016-93388E.indb 421-10-016-93388E.indb 4 10/15/2021 2:55:43 PM10/15/2021 2:55:43 PM

STEP 1: Plug the UPS into

a properly grounded outlet.

After plugging the UPS into a wall outlet, press and

hold the power button next to the STATUS LEDs to

turn on the UPS (See Basic Operation).

Note: The UPS will not turn on automatically in the

presence of live utility power.

STEP 2: Plug your equipment

into the UPS.

There are two sets of outlets on the back of your

UPS. Outlets marked SURGE ONLY / do not

provide battery backup power during power outages.

Connect common desktop items like printers,

scanners and other accessories not requiring

battery support to these outlets. Outlets marked

BATTERY BACKUP / offer UPS battery backup

support during power failures. Connect your vital

computer equipment into these outlets.

Your UPS is designed to support electronic

equipment only. You will overload the UPS if the

total volt-amp (VA) ratings for all the equipment

connected to the BATTERY BACKUP / outlets

exceed the UPS output capacity. To ﬁnd your

equipment’s VA ratings, look on their nameplates.

If the equipment is listed in amps (A), multiply

the number of amps by 120 to determine VA.

For example: 1A × 120 = 120VA. If you suspect

you have overloaded the outlets, remove some

equipment.

If the left-side green LED does not illuminate when

the UPS is turned ON, try the following:

1. Make sure that the UPS is plugged into a live AC

outlet.

2. Press and hold the power button next to the

STATUS LEDs to turn on the UPS. A beep should

sound when the UPS starts.

3. If the UPS still does not start, contact Tripp Lite

Tech Support for assistance.

Quick Installation

21-10-016-93388E.indb 521-10-016-93388E.indb 5 10/15/2021 2:55:43 PM10/15/2021 2:55:43 PM

Quick Installation

Optional Installation

Both UPS models include USB communication

ports and tel/DSL/Ethernet surge protection jacks

(not compatible with PoE applications). These

connections are optional, as the UPS will work

properly without these connections.

Basic Operation

UPS ON/OFF

• Plug the UPS into a live, grounded outlet.

The SURGE ONLY outlets will begin passing power.

• Plug equipment into the UPS.

You will overload the UPS if the total volt-amp (VA) ratings for all the equipment connected

to the BATTERY BACKUP outlets exceed the UPS output capacity. To ﬁnd your equipment’s

VA ratings, look on their nameplates. If the equipment is listed in amps (A), multiply the

number of amps by 120 to determine VA. For example:

1A × 120 = 120VA.

• Turn the UPS on.

Press and hold the power button next to the STATUS LEDs. The UPS alarm will beep once

brieﬂy and the left-side green LED will illuminate. The BATTERY BACKUP outlets will begin

passing AC line power. The UPS will automatically recharge internal batteries as needed.

Once turned on, your UPS is ready to protect connected equipment from blackouts,

brownouts, overvoltages and transient surges.

• Turn the UPS off.

Press and hold the power button next to the STATUS LEDs.

Note: UPS system will function properly upon initial startup; however, maximum runtime for the

unit’s battery will only be accessible after it has been charged for 24 hours.

21-10-016-93388E.indb 621-10-016-93388E.indb 6 10/15/2021 2:55:43 PM10/15/2021 2:55:43 PM

Basic Operation

LED Indicators

Description Green LED 1 Green LED 2 Red LED Alarm

Line Mode On On Off Off

Battery Mode Off

On (ﬂashes

OFF every 10

seconds)

Off Off

Battery Low Off Off (ﬂashes

every 1 second) On

Sounds every

1 second

Line Mode

Overload Alert* On On Off

Sounds every

0.5 second

Battery Mode

Overload Alert** Off Flashes Off Sounds every

0.5 second

Line Mode

Overload Fault* Off Off On Sounds

continuously

Battery Mode

Overload Fault** Off Off Off Off

Replace Battery On On Flashes every

1 minute

Sounds every

1 minute

Fault Condition Off Off On Sounds

continuously

*Line Mode Overload Alert Condition - 110%±10%, goes to fault after 5 minutes; Overload Fault Condition

- 120%±10%, goes to fault immediately.

**Battery Mode Overload Alert Condition - 110%±10%, shuts down in 5 seconds; Battery Mode Overload

Fault Condition - 120%±10%, shuts down immediately.

21-10-016-93388E.indb 721-10-016-93388E.indb 7 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Basic Operation

UPS Features

5 6 7

1 ON/OFF Button: When the UPS is on, press and release this button after one beep to

turn the UPS off.

2 LED Indicators: Provide current status of the UPS. For a detailed description, refer to

”LED Indicators” in the Basic Operation section.

3 Battery Backup/Surge Protected Outlets: These outlets offer battery backup support

and premium surge suppression for critical devices requiring battery backup support.

4 Surge Protected Outlets: These outlets offer premium surge suppression for additional

devices not requiring battery support.

5 USB Communication Port: This port can connect your UPS to any computer for

automatic saves and unattended shutdown in the event of a power failure. Use with

Tripp Lite’s PowerAlert® Software (available as a FREE download attripplite.com) and

the USB cable included with your UPS. This connection is optional; your UPS will work

properly without this connection.

Note: This UPS System provides basic communication compatibility with most integrated Windows®,

Macintosh® and Linux® power management applications.

6 Tel/DSL/Ethernet Line Protection Jacks: These jacks protect equipment against surges

over a single phone line or network connection. Connecting your equipment to these

jacks is optional; your UPS will work properly without this connection.

Note: Not compatible with PoE (Power over Ethernet) applications.

7 Resettable Input Circuit Breaker: Protects your electrical circuit from overcurrent draw

from the combined load of equipment connected to the UPS and surge-only outlets. If

this breaker trips, remove some of the load, then reset by pressing it in.

21-10-016-93388E.indb 821-10-016-93388E.indb 8 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Battery Replacement

Under normal conditions, the original battery in your UPS will last several years. Battery

replacement should only be performed by qualiﬁed personnel. Refer to “Battery Warnings” in

the Important Safety Instructions section for more information.

Models BC800U, INTERNET700U and INTERNET900U require one 12V DC, 7Ah replacement

battery.

For further information about replacement compatibility and ordering, visit

tripplite.com/products/battery-ﬁnder.

Battery replacement must be done using the same battery type and

quantity: 12V DC sealed lead-acid, 6-cell and in compliance with UL 1989.

CAUTION: Risk of energy hazard. Before replacing batteries, remove

conductive jewelry such as chains, wristwatches and rings. High energy

passing through conductive materials may cause severe burns.

21-10-016-93388E.indb 921-10-016-93388E.indb 9 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Storage and Service

Storage

To avoid battery drain, all connected equipment should be turned off and disconnected from

the UPS. Press and hold the power button next to the STATUS LEDs and disconnect the

unit from AC power. Your UPS will be completely turned off (deactivated) and will be ready

for storage. If you plan on storing your UPS for an extended period, fully recharge the UPS

batteries every three months. Plug the UPS into a live AC outlet, turn it on by pressing the

power button next to the STATUS LEDs and allow the batteries to recharge for 4 to 6 hours. If

you leave your UPS batteries discharged for a long period of time, they will suffer a permanent

loss of capacity.

Service

A variety of Extended Warranty and On-Site Service Programs are available from Tripp Lite.

For more information on service, visit tripplite.com/support.

Before returning your product for service, follow these steps:

1. Review the installation and operation procedures in this manual to ensure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

tripplite.com/support.

3. If the problem requires service, visit tripplite.com/support and click the Product Returns

link. From here you can request a Returned Material Authorization (RMA) number, which

is required for service. This simple on-line form will ask for your unit’s model and serial

numbers, along with other general purchaser information. The RMA number, along with

shipping instructions, will be emailed to you. Any damages (direct, indirect, special or

consequential) to the product incurred during shipment to Tripp Lite or an authorized

Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite or

an authorized Tripp Lite service center must have transportation charges prepaid. Mark

the RMA number on the outside of the package. If the product is within its warranty

period, enclose a copy of your sales receipt. Return the product for service using an

insured carrier to the address given to you when you request the RMA.

21-10-016-93388E.indb 1021-10-016-93388E.indb 10 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Speciﬁcations

Model INTERNET750U INTERNET900U

Nominal input voltage(s)

and range: 120V~ , 95-145V~ 120V~ , 95-145V~

Nominal input frequency

and tolerance: 50/60 Hz (+/- 5 Hz) 50/60 Hz (+/- 5 Hz)

Nominal output voltage: 120V~ sinusoidal in line mode,

120V~ PWM in battery mode 120V~ sinusoidal in line mode,

120V~ PWM in battery mode

Nominal output frequency: 50/60 Hz (+/-0.5 Hz) 50/60 Hz (+/-0.5 Hz)

Output voltage regulation

in line mode: 120 V~ (+/-20%) 120 V~ (+/-20%)

Output voltage regulation

in battery mode: 120V~ (+/-10%) 120V~ (+/-10%)

Nominal output power

in W / VA: 450W / 750VA 480W / 900VA

Output voltage waveform: Sinusoidal in line mode and

quasi-sine (PWM) in battery

mode

Sinusoidal in line mode and

quasi-sine (PWM) in battery

mode

Maximum output current

@ P.F. 6.3A @ 120V~ 7.5A @ 120V~

P.F. = 0.6 P.F. = 0.53

Efﬁciency with nominal load: 98% 98%

Maximum operating altitude

at 100% of nominal power: 2,000 m above the sea level 2,000 m above the sea level

Online overload capability: 110%±10%, goes to fault

after 5 min.; 120%±10%,

goes to fault immediately

110%±10%, goes to fault

after 5 min.; 120%±10%,

goes to fault immediately

Overload capacity in battery

mode: 110%±10%, shuts down in

5 sec.; 120%±10%,

shuts down immediately

110%±10%, shuts down in

5 sec.; 120%±10%,

shuts down immediately

Current limitation: Input 10A Input 10A

Autonomy time at full load: 2 minutes @ 450W 1.7 minutes @ 480W

Battery recharge time: 8 hours 8 hours

Transfer time: 6 milliseconds typical

(10 milliseconds max) 6 milliseconds typical

(10 milliseconds max)

Outlets: 6x 5-15R outlets with battery

backup, regulation and surge,

6x 5-15R outlets with surge only

6x 5-15R outlets with battery

backup,regulation and surge,

6x 5-15R outlets with surge only

Maximum input current: 10A 10A

21-10-016-93388E.indb 1121-10-016-93388E.indb 11 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Product Registration

Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a

drawing for a chance to win a FREE Tripp Lite product! *

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

FCC Part 68 Notice (United States Only)

If your Modem/Fax Protection causes harm to the telephone network, the telephone company may temporarily

discontinue your service. If possible, they will notify you in advance. If advance notice isn’t practical, you will be

notiﬁed as soon as possible. You will be advised of your right to ﬁle a complaint with the FCC. Your telephone

company may make changes in its facilities, equipment, operations or procedures that could affect the proper

operation of your equipment. If it does, you will be given advance notice to give you an opportunity to maintain

uninterrupted service. If you experience trouble with this equipment’s Modem/Fax Protection, please visit

tripplite.com/support for repair/warranty information. The telephone company may ask you to disconnect

this equipment from the network until the problem has been corrected or you are sure the equipment is not

malfunctioning. There are no repairs that can be made by the customer to the Modem/Fax Protection. This

equipment may not be used on coin service provided by the telephone company. Connection to party lines is

subject to state tariffs. (Contact your state public utility commission or corporation commission for information.)

FCC Notice, Class B

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modiﬁcations to this equipment not expressly approved by Tripp Lite could void the user’s authority

to operate this equipment.

Equipment Attachment Limitations (models with the Industry Canada label in Canada only)

NOTICE: The Industry Canada label identiﬁes certiﬁed equipment. This certiﬁcation means that the equipment

meets the telecommunications network protective, operational and safety requirements as prescribed in the

appropriate Terminal Equipment Technical Requirements Document(s). The Department does not guarantee the

equipment will operate to the user’s satisfaction. Before installing this equipment, users should ensure that it is

permissible to be connected to the facilities of the local telecommunications company. The equipment must also

be installed using an acceptable method of connection. The customer should be aware that the compliance with

the above conditions might not prevent degradation of service in some situations.

Repairs to certiﬁed equipment should be coordinated by a representative designated by the supplier. Any repairs

or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone

lines and internal metallic water pipe system, if present, are connected together. This precaution may be

particularly important in rural areas. Caution: Users should not attempt to make connections themselves, but

should contact the appropriate electric inspection authority, or electrician, as appropriate.

Regulatory Compliance

21-10-016-93388E.indb 1221-10-016-93388E.indb 12 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V : DC Voltage

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

Regulatory Compliance

Regulatory Compliance Identiﬁcation Numbers

For the purpose of regulatory compliance certiﬁcations and identiﬁcation, your Tripp Lite product has been

assigned a unique series number. The series number can be found on the product nameplate label, along with

all required approval markings and information. When requesting compliance information for this product, always

refer to the series number. The series number should not be confused with the marking name or model number of

the product.

Tripp Lite has a policy of continuous improvement. Product speciﬁcations are subject to change without notice.

Photos and illustrations may differ slightly from actual products.

21-10-016 93388E_RevC

21-10-016-93388E.indb 1321-10-016-93388E.indb 13 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Sistemas UPS

Modelos:

BC800U, INTERNET750U, INTERNET900U

(Números de Serie: AG-0314, AG-0317, AG-0390)

Manual del Propietario

1111 W. 35th Street, Chicago, IL 60609 EE UU • tripplite.com/support

English 1 • Français 26

21-10-016-93388E.indb 1421-10-016-93388E.indb 14 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

CONSERVE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse durante

la instalación, operación y almacenamiento de este producto. La omisión en la

observancia de estas advertencias puede afectar la garantía.

Advertencias para la Ubicación del UPS

• Instale su UPS en interiores, alejado de humedad o calor excesivos, contaminantes

conductores, polvo o luz solar directa.

• Para mejor desempeño, mantenga la temperatura interior entre 0 ºC a 40 ºC [32 ºF a 104 ºF].

• Deje espacio adecuado alrededor de todos los lados del UPS para una ventilación

adecuada.

• Instalación opcional: El UPS puede instalarse con seguridad en posición horizontal o

vertical. Para instalar, utilice dos tornillos (no proporcionados) para ﬁjar los agujeros

traseros del UPS a una superﬁcie plana.

Advertencias para la Conexión del UPS

• Conecte su UPS directamente a un tomacorrientes de CA conectado correctamente a

tierra. No enchufe el UPS en sí mismo; esto dañará al UPS.

• No modiﬁque la clavija del UPS y no use un adaptador que pueda eliminar la conexión a

tierra del UPS.

• No use cables de extensión para conectar el UPS a un tomacorrientes de CA.

• Si el UPS recibe alimentación de un generador de CA activado por motor, debe probarse

que el generador proporciona una salida de grado computadora, limpia y ﬁltrada.

• El tomacorrientes que alimenta al UPS debe ser fácilmente accesible y estar cerca del UPS.

Advertencias para la Conexión del Equipo

Instale de acuerdo con los estándares del Código Eléctrico Nacional ANSI /

NFPA 70 y Código Eléctrico Canadiense, Parte I, C22.1.

La protección de respaldo por corto circuito y la protección contra

sobrecorriente es proporcionada por la instalación del ediﬁcio.

Para reducir el riesgo de incendio, conecte solamente a un circuito con

una protección de sobrecorriente de circuito de 20A máximo según el

Código Eléctrico Nacional, ANSI/NFPA 70 y el Código Eléctrico Canadiense,

Parte I, C22.1. La clavija en el cable de alimentación está diseñada para

servir como dispositivo de desconexión. Asegúrese que el tomacorrientes

esté instalado cerca del equipo y sea fácilmente accesible.

El UPS está diseñado para utilizarse en un sistema de distribución de

energía TN.

Instrucciones de Seguridad Importantes

21-10-016-93388E.indb 1521-10-016-93388E.indb 15 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

• No se recomienda el uso de este equipo en aplicaciones de soporte de vida en donde

razonablemente se pueda esperar que la falla de este equipo cause la falla del equipo de

soporte de vida o afectar signiﬁcativamente su seguridad o efectividad.

• No conecte supresores de sobretensiones o cables de extensión a la salida de su UPS.

Esto puede dañar al UPS y afectar las garantías del supresor de sobretensiones y del UPS.

• Conecte el UPS a un tomacorrientes que esté adecuadamente protegido contra corrientes

excesivas, cortocircuitos, y fallas de conexión a tierra como parte de la instalación del ediﬁcio.

Instrucciones de Seguridad Importantes

Relevador principal

Breaker

Filtro I/P

Inversor

CD a CA

Convertidor

CD a CD

Cargador

CA a CD

Relevador O/P

IP-L O/P-L

IP-N O/P-N

IP/T O/P-T

21-10-016-93388E.indb 1621-10-016-93388E.indb 16 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Instrucciones de Seguridad Importantes

Advertencias de la Batería

• Debido a que las baterías presentan un peligro de choque eléctrico y quemaduras por

las altas corrientes de cortocircuito, tome las precauciones adecuadas. No deseche las

baterías en un incinerador. No abra las baterías. No ponga los terminales de la batería en

corto o en puente con ningún objeto. Apague y desconecte el UPS antes de reemplazar

la batería. Sólo debe cambiar las baterías personal técnico debidamente capacitado.

Use herramientas con mangos aislados y reemplace las baterías existentes con el mismo

número y tipo de baterías nuevas (plomo-ácido selladas). Las baterías del UPS son

reciclables. Consulte la reglamentación local para los requisitos de disposición de desechos

o visita tripplite.com/support/recycling-program para reciclar información. Tripp Lite ofrece

una línea completa de Cartuchos de reemplazo de batería para UPS (R.B.C.). Visite Tripp

Lite en la web en tripplite.com/products/battery-ﬁnder/ para localizar la batería de reemplazo

especíﬁca para su UPS.

PRECAUCIÓN: Una batería puede presentar un riesgo de descarga eléctrica

y alta corriente de cortocircuito. Hacer contacto con cualquier parte de una

batería conectada a tierra puede causar una descarga eléctrica. Al trabajar

con baterías deben observarse las siguientes precauciones:

• Retire relojes, anillos u otros objetos metálicos.

• Use herramientas con mangos aislados.

• Use botas y guantes de hule.

• No coloque herramientas o partes metálicas sobre la parte superior de las

baterías.

• Desconecte la fuente de carga y la carga antes de la instalación o el

mantenimiento de la batería.

• Desconecte el UPS del tomacorrientes de CA de la red pública. Desconecte todos

los cables, incluido el equipo conectado al UPS.

Reciclado de la batería y el UPS

Los productos de Tripp Lite usan baterías selladas de plomo-ácido, que son

altamente reciclables.

Llame a Tripp Lite al 1.773.869.1234 o visite tripplite.com/support/recycling-

program para obtener información adicional sobre el reciclado de baterías u otro

producto de Tripp Lite. Para los requisitos de desecho, por favor consulte sus

códigos locales.

Explicación de los Símbolos

Precaución Corriente

Alterna

Protegido

contra

Sobretensiones

Modo de

Respaldo por

Batería

Reciclable –

Contiene Plomo

21-10-016-93388E.indb 1721-10-016-93388E.indb 17 10/15/2021 2:55:44 PM10/15/2021 2:55:44 PM

Enchufe el UPS en

un tomacorrientes activo

conectado a tierra.

Después de enchufar el UPS en un tomacorrientes

en la pared, presione y sostenga el botón de

encendido próximo a los LEDs DE ESTADO para

encender el UPS (Vea Operación Básica).

Nota: El UPS no encenderá automáticamente en

presencia de energía activa de la red pública.

PASO 2: Enchufe su equipo en

el UPS.

Hay dos juegos de tomacorrientes en la parte

posterior de su UPS. Los tomacorrientes marcados

SURGE ONLY / no proporcionan respaldo de

energía por batería durante apagones. Conecte

en estos tomacorrientes los equipos de escritorio

comunes como impresoras, escáneres y otros

accesorios que no requieran respaldo por batería.

Los tomacorrientes marcados BATTERY BACKUP /

ofrecen respaldo por batería del UPS

durante fallas de la energía. Conecte en estos

tomacorrientes sus equipos de cómputo vitales.

Su UPS está diseñado para soportar solamente

equipo electrónico. Usted sobrecargará el UPS

si el valor total en volt-amperes (VA) para todo el

equipo conectado a los tomacorrientes BATTERY

BACKUP / excede la capacidad de salida del

UPS. Para localizar los valores de VA de su equipo,

consulte las placas de identiﬁcación. Si el equipo

está especiﬁcado en amperes (A), multiplique el

número de amperes por 120 para determinar VA.

Por ejemplo: 1A × 120 = 120VA. Si sospecha que

ha sobrecargado los tomacorrientes, retire algunos

equipos.

Si el LED verde de la izquierda no se ilumina

cuando se enciende el UPS, intente lo siguiente:

1. Asegúrese de que el UPS esté conectado a un

tomacorrientes de CA.

2. Presione y sostenga el botón de encendido

junto a los LEDs DE ESTADO para encender el

UPS. Sonará un bip cuando el UPS arranque.

3. Si el UPS aún no arranca, póngase en contacto con

Soporte Técnico de Tripp Lite para solicitar apoyo.

Instalación Rápida

21-10-016-93388E.indb 1821-10-016-93388E.indb 18 10/15/2021 2:55:45 PM10/15/2021 2:55:45 PM

Instalación Rápida

Instalación Opcional

Ambos modelos de UPS incluyen puertos de

comunicación USB y conectores de supresión de

sobretensiones Tel / DSL / Ethernet (no compatible

con aplicaciones PoE). Estas conexiones son

opcionales, el UPS funcionará adecuadamente sin

estas conexiones.

Operación Básica

ENCENDIDO Y APAGADO DEL UPS

• Enchufe el UPS en un tomacorrientes activo conectado a tierra.

Los tomacorrientes SURGE ONLY [Únicamente protegidos contra sobretensiones]

empezarán a pasar alimentación.

• Enchufe los equipos en el UPS.

Usted sobrecargará el UPS si el valor total en volt-amperes (VA) para todo el equipo

conectado a los tomacorrientes BATTERY BACKUP [Respaldados por batería] excede la

capacidad de salida del UPS. Para localizar los valores de VA de su equipo, consulte las

placas de identiﬁcación. Si el equipo está especiﬁcado en amperes (A), multiplique el

número de amperes por 120 para determinar VA. Por ejemplo:

1A × 120 = 120VA.

• Encienda el UPS.

Presione y sostenga el botón de encendido junto a los LEDs DE ESTADO. La alarma del

UPS sonará brevemente una vez y se encenderá el LED verde izquierdo. Los tomacorrientes

BATTERY BACKUP empezarán a pasar energía de la línea de CA. El UPS recargará

automáticamente las baterías internas según sea necesario. Una vez encendido, su

UPS está listo para proteger los equipos conectados contra apagones, caídas de voltaje,

sobrevoltajes y sobretensiones transientes.

• Apague el UPS.

Presione y sostenga por el botón de encendido junto a los LEDs DE ESTADO.

Nota: El sistema UPS funcionará correctamente en el arranque inicial; no obstante, la autonomía

máxima para la batería de la unidad sólo será accesible después de haberse cargado por 24 horas.

21-10-016-93388E.indb 1921-10-016-93388E.indb 19 10/15/2021 2:55:45 PM10/15/2021 2:55:45 PM

Operación Básica

Indicadores LED

Descripción LED Verde 1 LED Verde 2 LED Rojo Alarma

Modo en Línea Encendido Encendido Apagado Apagado

Modo de

Respaldo por

Batería

Apagado

Encendido

(destella

OFF cada

10 segundos)

Apagado Apagado

Batería Baja Apagado

Apagado

(destella cada

1 segundo)

Encendido

Suena cada

1 segundo

Alerta por

Sobrecarga en el

Modo En Línea*

Encendido Encendido Apagado

Suena cada

0.5 segundos

Alerta por

Sobrecarga en

el Modo de en

Respaldo por

Batería**

Apagado Destella Apagado Suena cada

0.5 segundos

Falla por

Sobrecarga en el

Modo En Línea*

Apagado Apagado Encendido Suena

continuamente.

Falla por

Sobrecarga en

el Modo de en

Respaldo por

Batería**

Apagado Apagado Apagado Apagado

Reemplace su

Batería Encendido Encendido Destella cada

1 minuto

Suena cada

1 minuto

Condición de

Falla Apagado Apagado Encendido Suena

continuamente.

*Condición de Alerta por Sobrecarga en el Modo en Línea - 110% ±10%, se va a falla después de 5

minutos; Condición de Falla por Sobrecarga - 120% ±10%, se va a falla inmediatamente.

**Condición de Alerta por Sobrecarga en el Modo de Respaldo por Batería - 110% ±10%, se apaga en

5 segundos; Condición de Falla por Sobrecarga en el Modo de Respaldo por Batería - 120% ±10%, se

apaga inmediatamente.

21-10-016-93388E.indb 2021-10-016-93388E.indb 20 10/15/2021 2:55:45 PM10/15/2021 2:55:45 PM

La page charge ...

Tripp Lite BC800U Le manuel du propriétaire

Marque: Tripp Lite

Modèle: BC800U

Catégorie: Alimentations sans interruption (UPS)

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Tripp Lite BC800U Owner's manual
español: Tripp Lite BC800U El manual del propietario

Documents connexes

Autres documents

Humanscale NeatHub Mode d'emploi