Arris VIP7300 Guide d'installation

Marque: Arris

Modèle: VIP7300

Taper: Guide d'installation

Hereby, ARRIS declares that the radio equipment type VIP7300

is in compliance with Direcve 2014/53/EU. The full text of

the EU declaraon of conformity is available at the following

Internet address: hp://arris.com/consumers/eudoc.

In accordance with Commission Regulaon (EU) 2019/1782,

energy eciency data for the power supply provided with

this product is available here: hps://www.commscope.com/

consumers/psuinfo.

Disabling Wireless: This equipment is dependent on wireless

for primary operaon. To disable wireless disconnect the

product from power. Installation Guide

VIP7300

Set-top box

Caring for the Environment by Recycling

When you see this symbol on an ARRIS product,

do not dispose of the product with residenal

or commercial waste. Some countries or regions

have set up systems to collect and recycle electri-

cal and electronic waste items. Recycling informa-

on can be obtained from the WEEE recycling

secon at www.CommScope.com.

Please recycle product packaging and this

document.

Ambient operang

temperature

0 °C to +40 °C

Voltage 100-240 V~,50/60 Hz, 1A max

Power supply unit This Class II product, VIP7300, shall

be powered by the Limited Power

Supply that is provided together

with the product.

Maximum Power

consumpon

12 W

504-xxxxx00

The following table shows the maximum EU RF Output Power:

Frequency Band (GHz) Maximum RF Power (dBm)

2.4 to 2.48 10

5.150 – 5.350* 23

5.470 – 5.725 23

*Indoor use only BE, BG, CZ, DK, DE, EE, IE, EL, ES, FR, HR,

IT, CY, LV, LT, LU, HU, MT, NL, AT, PL, PT, RO, SI, SK, FI, SE, and

UK(NI).

Front panel

LED indicators:

•On: Blue

•Standby: Red

Rear panel

POWER

For connecons to the power

supply included in the package

ETHERNET

For broadband connecon

HDMI

For connecon to your TV

(High and Standard Denion

digital video and digital audio)

OPTICAL

For connecon to your

audio/home theatre system

In the box

VIP7300 HDMI cable Power supply

RCU

EU Compliance is maintained at the following address:

ARRIS Group B.V., Hoogoorddreef 5,

1101 BA Amsterdam-Zuidoost, The Netherlands

ARRIS and the ARRIS Logo are trademarks of CommScope,

Inc. and/or its aliates. All other trademarks are the

property of their respecve owners.

The terms HDMI, HDMI High-Denion Mulmedia Interface,

and the HDMI Logo are trademarks or registered trademarks

of HDMI Licensing Administrator, Inc.

Manufactured under license from Dolby Laboratories.

Dolby, Dolby Audio, Pro Logic, and the double-D symbol are

trademarks of Dolby Laboratories Licensing Corporaon.

NOTE:

Do not use any power supply other than the

one supplied with the product. Doing so may

cause re or seriously damage your set-top

box.

INSTALLING YOUR SET-TOP BOX

Power outlet

Connect one end of the power

supply to POWER port on your

set-top box and to the power

outlet.

Connect your set-top box to your home

Wi-Fi network.

123

Connect one end of the HDMI cable to

the HDMI port on your set-top box and

the other end to the HDMI connector on

to your TV.

To display a picture from your set-top

box, your TV must be switched to the

correct external input. This is either done

automacally or manually, using a buon

on the TV remote control. See your TV

user’s guide for instrucons.

Insert the baeries into your remote

control.

The remote control will iniate

pairing with your set-top box when

baeries are inserted and any key is

pressed.

NOTE:When removing the Ethernet/

LAN cable make sure to rmly press the

underside latching tab on the Ethernet/

LAN cable; to unlock the cable from the

Ethernet/LAN port on the product.

IMPORTANT SAFETY INSTRUCTIONS

• Never place the product on top of or close to any

heat sources such as other electronic devices. Doing

so will reduce lifeme and may cause irreparable

damage or malfuncon. Do not use the product near

water. Note that the ambient temperature must be

below 104° F/40 C. Be sure to maintain necessary

space around the product to allow for proper

venlaon.

• Never use the product outside. The product is

designed to stand on a horizontal surface.

• Do not use any power supply other than the one

supplied with the product. Doing so may cause re or

seriously damage the product.

Federal Communicaon Commission Interference

Statement:This device complies with Part 15 of the

FCC Rules. Operaon is subject to the following two

condions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operaon.

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protecon

against harmful interference in a residenal

installaon. This equipment generates, uses and can

radiate radio frequency energy and, if not installed

dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV

technician for help.

FCC Cauon: Any changes or modicaons not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

this equipment. This transmier must not be co-

located or operang in conjuncon with any other

antenna or transmier.

Radiaon Exposure Statement:This equipment

complies with FCC radiaon exposure limits set forth

for an uncontrolled environment. This equipment

should be installed and operated with minimum

distance 20cm between the radiator and your body.

and used in accordance with the instrucons,

may cause harmful interference to radio

communicaons. However, there is no guarantee

that interference will not occur in a parcular

installaon. If this equipment does cause harmful

interference to radio or television recepon, which

can be determined by turning the equipment o

and on, the user is encouraged to try to correct

the interference by one of the

following measures.

- Reorient or relocate the receiving antenna.

- Increase the separaon between the equipment

and receiver.

- Connect the equipment into an outlet on a circuit

Alternavely: Connect one end of the

Ethernet cable (not included) to the

Ethernet port on your set-top box and

the other end to your home router.

IC Warning

- English: "

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

- French:"

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement."

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by

Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated

power (e.i.r.p.) is not more than that necessary for

successful communication.

Selon les règlements d'Industrie Canada, cet émetteur radio ne peut fonctionner qu'à l'aide d'une antenne d'un type et d'un gain maximal (ou moindre) approuvé pour

l'émetteur par Industrie Canada. Pour réduire les interférences radioélectriques potentielles avec d'autres utilisateurs, le type d'antenne et son gain doivent être choisis

de telle sorte que la puissance équivalente rayonnée (p.i.r.e.) ne soit pas supérieure à celle nécessaire pour une communication réussie.

STATEMENT OF RADIATION EXPOSURE:

This equipment complies with the limites of exposure to IC radiation established for an uncontrolled environment. This equipment must be installed and used with a

minimum of 20cm distance between the radiation source and your body.

DÉCLARATION D'EXPOSITION AUX RADIATIONS:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé

avec un minimum de 20cm de distance entre la source de rayonnement et votre corps.