Norcold 2118 PolarMax Le manuel du propriétaire

Marque: Norcold

Modèle: 2118 PolarMax

Catégorie: Boissons glacées

Taper: Le manuel du propriétaire

Improper installation, adjustment, alteration, service or maintenance can

cause injury or property damage. Refer to this manual. For assistance

or additional information, contact a qualied installer, service agency, or

the gas supplier.

NORCOLD, Inc.

P.O. Box 4248

Sidney, OH 45365-4248

Part No. 636900B (09/2/2021)

English Norcold Customer Support Dept.

Telephone: 800-543-1219

Fax: 734-769-2332

Web Site: www.norcold.com

Owner’s Manual

for the 2118X series of RV Refrigerators

The letter “X”, in the model numbers above, stands for letters or numerals which means a

refrigerator option.

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other ammable vapors and liquid in the

vicinity of this or any other appliance.

FIRE OR EXPLOSION HAZARD

If you smell gas:

1. Open Windows

2. Do not attempt to light appliances and make sure the appliance is in the o

position.

3. Extinguish any open ame

4. Do not touch electrical switches.

5. Do not use elctronic devices such as cell phones or landline phone.

6. Evacuate the building or recreational vehicle

7. Shut o fuel supply at LP tank.

8. Call emergency services.

Failure to follow these instructions could result in re or explosion, which could cause property

damage, personal injury, or death.

CARBON MONOXIDE POISONING MAY CAUSE DEATH OR INJURY.

When used without adequate combustion and ventilation air, the refrigerator may give o excess

CARBON MONOXIDE, and odorless poisonous gas. This is an unvented gas-red appliance. The

refrigerator uses air (oxygen) from the area in which the refrigerator is used. Adequate combustion

and ventilation air must be provided.

WARNING

Owner’s Manual 2

Table of Contents

For dened warranty terms, please see the one page warranty statement included in the product information packet.

Safety Awareness ........................................................................................................................................................................................ 2

Safety Instructions ....................................................................................................................................................................................... 3

About Your Refrigerator ............................................................................................................................................................................... 3

Storage volume .................................................................................................................................................................................... 3

Leveling ................................................................................................................................................................................................ 3

Operation during travel ......................................................................................................................................................................... 4

Food compartment ............................................................................................................................................................................... 4

Freezer compartment ........................................................................................................................................................................... 4

Door handles ........................................................................................................................................................................................ 4

Moveable door seal .............................................................................................................................................................................. 4

Crispers and beverage bin ................................................................................................................................................................... 4

Door bins .............................................................................................................................................................................................. 6

Door alarm ........................................................................................................................................................................................... 6

Interior light........................................................................................................................................................................................... 7

Moisture reduction heaters ................................................................................................................................................................... 7

Temperature Control System................................................................................................................................................................ 7

Backup operating system ..................................................................................................................................................................... 7

Temperature switch monitor ................................................................................................................................................................. 8

Operating the Refrigerator Controls ............................................................................................................................................................ 8

Control panel ........................................................................................................................................................................................ 8

Automatic mode operation ................................................................................................................................................................. 10

Removing air from the propane gas supply lines ............................................................................................................................... 10

Set the controls to manual mode operation .................................................................................................................................11

Eects of High Altitude on Propane Gas Operation ...................................................................................................................................11

Eects of Freezing Temperatures on Refrigerator Operation .....................................................................................................................11

Ice Maker ................................................................................................................................................................................................... 12

Ice Maker Operation ........................................................................................................................................................................... 12

Refrigerator Care Checklist ....................................................................................................................................................................... 13

Defrosting .................................................................................................................................................................................................. 13

Cleaning .................................................................................................................................................................................................... 14

Interior ................................................................................................................................................................................................ 14

Metal doors ................................................................................................................................................................................................ 14

Door Sealing .............................................................................................................................................................................................. 15

Refrigerator Storage .................................................................................................................................................................................. 15

Ice Maker Storage ..................................................................................................................................................................................... 15

Refrigerator Maintenance Checklist ......................................................................................................................................................... 16

Refrigerator Maintenance .......................................................................................................................................................................... 17

Gas ame appearance ....................................................................................................................................................................... 17

Remove and clean the burner orice ................................................................................................................................................. 17

Remove the Refrigerator ........................................................................................................................................................................... 18

Reinstall the Refrigerator ........................................................................................................................................................................... 19

Replacement Parts .................................................................................................................................................................................... 19

Fault Codes ............................................................................................................................................................................................... 20

Wiring Diagram and Pictorial ..................................................................................................................................................................... 21

Ice Maker Wiring Diagram and Pictorial .................................................................................................................................................... 23

Wiring Diagram and Pictorial - Low Ambient Heater ................................................................................................................................. 23

Safety Awareness

Read this manual carefully and understand the contents before you use the refrigerator.

Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows

the safety alert symbol and identies the danger of the hazard. Carefully read the descriptions of these signal words to fully know their

meanings. They are for your safety.

This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much

property damage.

This signal word means a hazard, which if ignored, can cause small personal injury or much property

damage.

CAUTION

WARNING

Owner’s Manual 3

Safety Instructions

- The storage of ammable materials behind or around the refrigerator creates a re hazard. Do not use the area

behind the refrigerator to store anything, especially ammable materials (gasoline, cleaning supplies, etc.)

- Do not remove the round ground prong from the AC power cord of the refrigerator or the ice maker (optional). Do not

use a two prong adapter or an extension cord with either AC power cord.

- A circuit overload can result in an electrical re if the wires and/or fuses are not the correct size. Use only the wire

and fuse sizes as writtten in the “Installation Manual”.

- Incorrect installation, adjustment, change to, or maintenance of this refrigerator can cause personal injury, property

damage, or both. Have service and maintenance work done by your dealer or by an Norcold authorized service

center.

- Disconnect both the AC and DC power sources before doing any maintenance work on the refrigerator. All service

work on this refrigerator must be done by a qualied service technician.

- Do not bypass or change the refrigerator’s electrical components or features.

- When you discard an appliance, remove all doors to prevent accidental entrapment and suocation.

- Do not spray liquids near electrical outlets, connections, or the refrigerator components. Many liquids are electrically

conductive and can cause a shock hazard, electrical shorts, and in some cases re.

- The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system. The

cooling system contains sodium chromate. The breathing of certain chromium compounds can cause cancer. The

cooling system contents can cause severe skin and eye burns, and can ignite and burn with an intense ame. Do not

bend, drop, weld, move, drill, puncture, or hit the cooling system.

- At regular intervals, make sure that the refrigerator ue, the burner, the vent areas, and the ventilation air pathway

between the vents are completely free from any ammable material or blockage. After a period of storage, it is

especially important to check these areas for any ammable material or blockage caused by animals.

- The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the

refrigerator, be careful and wear cut resistant gloves.

About Your Refrigerator

Storage Volume:

This refrigerator is made for storage of foods and frozen food and for making ice.

Total capacity 18.0 cubic feet

Freezer Compartment 5.8 cubic feet

Fresh Food Compartment 12.2 cubic feet

Leveling:

The refrigerator is made to operate within 3° o level side-to-side and 6° o level front-to-back (as looking at

the front of the refrigerator). Operating it at more than these limits can cause damage to the cooling system

and create a risk of personal injury or property damage. Make sure the vehicle is level before you operate

the refrigerator.

WARNING

CAUTION

Owner’s Manual 4

Operation during travel:

While the refrigerator should be level when the vehicle is stopped, performance

during travel is not usually eected.

Food compartment:

Start up the refrigerator (see “Operating the Refrigerator Controls”)and let it cool

for eight hours before loading with food. If the refrigerator does not start to cool

down after about two hours, contact your dealer or a Norcold authorized service

center.

For the best cooling performance:

- Let air move freely inside the entire food compartment.

- Do not cover the shelves with plastic, paper, etc.

To decrease the amount of ice that collects on the cooling ns:

- Cover all liquids and moist foods.

- Let all hot foods cool before putting them in the refrigerator.

- Do not open the door any longer than necessary.

Freezer compartment:

The freezer compartment is made to keep pre-frozen food frozen and not to quick freeze

food.

Door handles:

During travel, the door latch prevents the door from opening. When closing each door, push

the door toward the refrigerator until you hear a “click” sound.

To open each door, pull the handle away from the refrigerator (See Art02494).

Movable door seal:

The movable door seal [134] is located on the left door of the fresh food

compartment (See Art0813). It provides the correct seal when both doors of

the fresh food compartment are closed. When the left door of the fresh food

compartment opens, the movable door seal moves so that it is at against

the edge of the door. To avoid possible damage to the movable door seal,

make sure that it is at against the edge of the door before you close the

door

Crispers and beverage bin:

The crispers are located at the bottom of the fresh food compartment and supply a

storage area to preserve fruit and vegetable freshness. Make sure that you always

push the crispers fully in. The crisper covers open as the crispers open and close as

the crispers close.

Each crisper also has an adjustable vent that is used to adjust the humidity inside

each crisper. Move each vent toward the right (high humidity) for most vegetables or

toward the left (low humidity) for most fruits (See Art01834).

134

Art01813

Art01834

ART 02494

Art 02498

197

135

Owner’s Manual 5

The crispers, crisper covers, beverage bin, and beverage bin cover are

removable for cleaning.

Do not wash the crispers, crisper covers, beverage bin, or

beverage bin cover in a dishwasher. These parts are not

dishwasher safe.

To remove the crisper covers (See Art02498):

- With the crisper closed, lift the crisper cover[135] to the fully raised

position.

- Locate the hinge pins[71] that are part of the crisper cover rails [197].

- Push the front of one of the crisper cover rails inward toward the

crisper so you can lift that side of the crisper cover o of the hinge pin.

- Slide the opposite side of the crisper cover o of the other hinge pin.

- To reinstall the crisper covers, do this procedure in the opposite order.

To remove the crispers (See Art02499):

- Pull each crisper forward until it reaches the “stop” position.

- Lift up on the front of the crisper [a] and continue to pull the crisper out

[b].

- To reinstall the crispers, do this procedure in the opposite order.

To remove the bottom full shelf (See Art02500):

- Remove the crisper covers, the crispers, the beverage bin and the

beverage bin cover.

- Locate the two (2) screws [41] that attach the bottom full shelf [200]

(one screw is on the bottom of each side).

- Remove and save the screws and the plastic spacers [201].

- Using both hands, slide the shelf out of the rails.

- To reinstall the bottom full shelf, do this procedure in the

opposite order.

To remove the top full shelf (See Art02495):

- Locate the screws that attach the plastic clips [202] (the

top shelf clips are located at the end of each shelf and the

lower shelf clips are located in the center of the shelf.

- Remove and save the screws and the plastic clips.

- Pul the top full shelf forward [203] to remove.

- To reinstall the top full shelf, do this procedure in the

opposite order.

NOTICE

Art 02495

203

202

Art 02499

Art02500

201

200

Owner’s Manual 6

Door bins:

You may put the small door bins [52] of the freezer and fresh food compartment in a location that best meets your needs. You must put

the large door bins in the lowest positions or else the large door bins will touch the shelves and the doors wil not close (See Art 01815).

To remove the bins, lift them over the locator and pull them forward. To install the bins, push them onto the locator.

Do not wash the door bins in a dishwasher. The door bins are not dishwasher safe.

Door alarm:

The refrigerator has an alarm to alert you if a fresh food compartment door is not closed. The refrigerator continues to operate, but if a

fresh food compartment door is open and the interior light remains on for two minutes:

- An audible alarm starts.

- “dr” appears in the center display.

- The interior light automatically turns o.

Close the door to silence the alarm.

Art01815

NOTICE

Owner’s Manual 7

Interior light:

The interior light is at the top of the fresh food compartment. It comes on when the

refrigerator is ON and the door is open. To replace the bulb:

1. Remove the DC power supply wires from the power board at the rear of the refrigerator.

2. Remove the cover [57] by pulling it toward the front of the refrigerator (See Art00988).

3. Remove the light bulb [58] from the holder [59].

Use only a GE#214-2 bulb as the replacement bulb. This bulb is available

at most retail automotive parts centers.

4. Install the replacement bulb.

5. Install the cover.

6. Connect the DC power supply wires to the power board at the rear of the refrigerator.

Moisture reduction heaters:

The refrigerator has heaters that prevent moisture from forming on the center divider between the two doors and the perimeter of

the freezer compartment, and on the movable door seal. The heaters operate only when the refrigerator is ON and the DC power is

sucient. The heater in the movable door seal also only operates when both doors of the fresh food compartment are closed.

Temperature control system:

Although the refrigerator is not frost -free, it is made to limit frost on the cooling ns. At regular intervals, the temperature control system

automatically melts most of the frost from the cooling ns. The water from the cooling ns drains into a collection cup that is attached

to the back of the refrigerator. The heat of the cooling system evaporates the water from the collection cup.

Backup operating system:

This refrigerator has a backup operating system. The backup operating system allows the regerator to continue to cool if the

temperature sensor of the refrigerator should fail.

If this failure occurs:

- The refrigerator automatically changes to the backup operating system.

- When you push the TEMP SET button, the temperature setting ashes in the center display for ten seconds.

- The backup operating system can overfreeze or thaw the contents of the freezer and the fresh food compartment.

- Make sure the temperatures of the freezer and the fresh food compartment are satisfactory.

Art00988

NOTICE

Owner’s Manual 8

Operating the Refrigerator Controls

Temperature switch monitor:

The refrigerator is equipped with a temperature switch [142] for

overheating protection (See Art02496) . A Norcold authorized service

technician can determine if this switch has been triggered.

Control panel:

The refrigerator control panel (See Art02492) is between the freezer compartment and the fresh food compartment. A 12 volt DC power

supply is necessary for the control functions of the refrigerator to operate. The refrigerator receives DC power from the 12 volt system of

the vehicle; either an auxiliary battery, a converter, or the vehicle engine battery.

The POWER ON/OFF button [30] starts and shuts down the refrigerator.

- Push and release the POWER ON/OFF button [30] to turn on the refrigerator.

- Push and hold the POWER ON/OFF button [30] for one second to turn o the refrigerator.

The MODE button [31] changes the modes of operation of the refrigerator.

- Push and hold the MODE button [31] to scroll through the available operation modes of the refrigerator, one after the other (See

Art02397).

- When the desired mode indicator comes on, release the MODE button.

142

ART 02496

set

ART 02492

30 31

280 278

Owner’s Manual 9

- Or push and release the MODE button again and

again to change the available operation modes of the

refrigerator, one at a time.

- As you change the mode, the applicable mode

indicator will come on.

- The mode indicators are (See Art02493):

- Auto mode AC electric [281].

- Auto mode gas [282].

- Manual mode AC electric [283].

- Manual mode gas [284].

- Select one of three (3) modes of operation

AUTO mode The refrigerator’s electronic controls automatically select the the most ecient energy source that is

available. Either the Auto mode AC indicator [281], the Auto mode gas indicator [282], comes on.

MANUAL AC mode The refrigerator cools using only AC electric power as the power source. The Manual mode AC

indicator [283] comes on.

MANUAL GAS mode The refrigerator cools using only propane gas as the power source. The Manual mode gas

indicator [284] comes on.

Select the temperature setting:

- Push and hold the TEMPERATURE SET button [32] to scroll through the temperature settings, one after the other (See Art02492).

- Or push and release the TEMPERATURE SET button again and again to change the temperature settings, one at a time.

- The temperature settings come on as numbers in the LCD.

- Select one of nine (9) temperature settings:

- The number one (1) is the warmest temperature setting.

- The number nine (9) is the coldest temperature setting.

ART 02493

set

set set

284

282

281

283

Owner’s Manual 10

Automatic mode operation:

When the refrigerator is in AUTO mode, the electronic controls of the refrigerator automatically select and use the most ecient energy

source that is available for operation.

During operation, if a more ecient energy source becomes available, the electronic controls of the refrigerator automatically changes

from the current energy source to the more ecient energy source as follows:

- The rst choice of operation is AC electric mode.

- If AC electric is not available to the refrigerator, if the AC electric is outside of the permitted operating range, or if the AC heater

does not operate; the electronic controls of the refrigerator automatically change to the second choice of operation.

- The second choice of operation is gas mode.

- The refrigerator attempts to operate the propane gas burner. If unable to establish and maintain a ame, a “no” FL” fault code

shows on the LCD. Refer to “Fault Codes” section of this manual.

Removing air from the propane gas supply lines:

For safety reasons, the burner is made to ignite on propane gas within a specied amount of time. When starting the refrigerator for the

rst time, after storage, or after replacing the propane gas tank, the propane gas supply lines can have air in them. Due to the air in the

gas supply lines, the refrigerator may not ignite on propane gas within the specied amount of time.

To remove the air from the propane gas supply lines:

- Make sure that all of the gas valves are open.

- Push and release the POWER ON/OFF button [30] to turn on the refrigerator.

- Push and hold the MODE button [31] until the Manual mode gas indicator [284] is on.

- Push and release the TEMPERATURE SET button until the desired temperature setting shows.

- The refrigerator will start a 30 second trial for ignition.

- During the 30 second trial for ignition, the refrigerator controls open the gas safety valve and the igniter sparks.

- After 30 seconds, if the Manual mode gas indicator remains on, it means that the refrigerator is operating on propane gas.

- At this time, all of the air is removed from the propane gas supply lines and you may select AUTO mode of operation if

you wish.

- If the gas does not ignite within 30 seconds, the gas valve of the refrigerator will automatically close and a “no” “FL” fault code

will show in the LCD. To reset the controls, press and hold the POWER ON/OFF button for 1 second to turn the refrigerator

o, then press it again to restart the refrigerator and begin another 30 second trial for ignition.

- Depending on how much air may be in the propane gas supply lines, you may need to repeat the 30 second trial for

ignition two or three times.

- If the burner does not ignite on propane gas after two or three attempts, stop and consult your local dealer or an

authorized Norcold Service Center.

Owner’s Manual 11

Eects of High Altitude on Propane Gas Operation

When you operate the refrigerator on propane gas at altitudes higher than 5500 feet above sea level:

- You may experience reduced cooling performance of the refrigerator.

- You may experience burner outages.

To avoid these possible problems, Norcold recommends that you operate the refrigerator on AC when at altitudes higher than 5500 feet

above sea level.

Eects of Freezing Temperatures on Refrigerator Operation

A gas absorption refrigerator is not designed to operate in freezing temperatures. If the refrigerator is not equipped for low temperature

operation, and if the cooling system of the refrigerator is exposed to temperatures of 32° F. or lower for an extended period of time,

the refrigerator operation may be disrupted. The refrigerator operation will resume when the cooling system of the refrigerator warms

suciently.

The refrigerator is equipped for low temperature operation. The refrigerator will operate in temperatures down to 0° F with the cold

weather kit provided if connected.

Disrupted operation of the refrigerator, due to extended exposure to temperatures of 32° F. or lower, and any costs incurred to warm the

cooling system of the refrigerator are not covered by the Norcold limited warranty. Please contact your local RV dealer for information

about how to resume refrigerator operation or about how to equip your refrigerator for operation in freezing temperatures.

Do not change the installation or the venting of your refrigerator. Refrigerator failures, which are the result of changes to either the

refrigerator installation or to the venting, are not covered by the Norcold limited warranty.

Set the controls to manual mode operation:

- Push and release the POWER ON/OFF button [30] to turn on the refrigerator.(See Art02493)

- Push and hold the MODE button [31] until the desired Manual mode indicator comes on.

- Manual mode AC electric [283].

- Manual mode gas [284].

If the energy source is interrupted:

- A fault code shows in the LCD.

- Refer to the “Fault Codes” section of this manual.

Shut down:

- Push and hold the POWER ON/OFF button [30] for one second to turn o the refrigerator.

This kit supplies DC voltage to the heater any time the ambient temperature is low enough. Extended storage during

cold weather will drain the vehicle batteries. To prevent battery drain, remove the 3 amp fuse from the low ambient

heater.

NOTICE

Owner’s Manual 12

Ice Maker

The ice maker is fully automatic and will operate in ambient temperatures as low as 0° F. To allow operation at temperatures between

0° F and 32° F., the ice maker has a heater on the solenoid water valve and on the water line between the solenoid valve and the ice

maker. At temperatures below 0° F, store the ice maker as written in the “Ice Maker Storage” section of this manual.

The water line heater does not protect the water supply line from the vehicle shut o valve to the solenoid

valve on the back of the refrigerator.

When the freezer temperature of the refrigerator is low enough, the ice maker opens the water solenoid valve and lls the mold. The

ice maker ejects the frozen ice into a storage bin. As the storage bin lls, the ice raises the shut-o arm until it turns o the ice maker.

As you use the ice and lower the ice level in the storage bin, the shut-o arm also lowers. This turns the ice maker ON and begins the

process of making ice.

The ice maker operates on:

- Cold potable water at a pressure of 15 psi - 125 psi.

- 120 Volts AC (108 VAC min. - 132 VAC max.).

Ice maker operation:

1. Make sure the ice maker AC power cord is plugged into a receptacle.

2. Open the water shut o valve of the vehicle.

Make sure that the ice maker arm can move freely and does not touch the

frozen foods in the freezer.

3. Push the ice maker arm down to the ON position [60] (See Art01015).

If you operate the refrigerator without connecting the water supply line

and/or opening the water shut o valve of the vehicle, make sure the

ice maker arm is up in the OFF position.

4. Allow the freezer to cool enough and ice production will begin to ll the storage bin [61].

New plumbing connections and/or impurities in the water supply line after

winterizing can cause the rst ice to be discolored or have an odd avor.

5. To stop the ice maker, push the ice maker arm up to the OFF position [62].

Art01015

CAUTION

NOTICE

Owner’s Manual 13

Refrigerator Care Checklist

Your refrigerator will give you years of trouble free service if you do these simple checks every three to six months:

- Keep the food compartment and the freezer clean. See “Cleaning”.

- Make sure the door seals correctly. See “Door Sealing“.

- Be aware of any cooling changes that are not because of weather, loading, or gas control changes. If changes occur, contact your

dealer or service center.

- Make sure the gas supply is propane gas only and not butane or a butane mixture.

- When in propane gas operation, examine the appearance of the ame. See “Gas Flame Appearance”.

- Make sure the air ow in the lower intake vent, through the refrigerator coils and condenser, and out the upper exhaust vent is not

blocked or decreased.

- Make sure the area behind the refrigerator is clear. Do not use the area behind the refrigerator for storage of anything, especially

combustible materials, especially gasoline and other ammable vapors and liquids.

Defrosting

The cooling ns of the refrigerator operate at below freezing temperature and will naturally form frost from humidity, which is always

present in the air. The humidity inside the refrigerator increases:

- with higher outside temperature and humidity.

- with the storage of non-sealed fresh foods or warm foods.

- with the amount of time that the door(s) are open.

- with any air leakage into the refrigerator.

Although the refrigerator is not frost -free, it is made to limit frost on the cooling ns. At regular intervals, the temperature control system

automatically melts most of the frost from the cooling ns. The water from the cooling ns drains into a collection cup that is attached to

the back of the refrigerator. The heat of the cooling system evaporates the water from the collection cup.

It is normal for frost to collect inside the freezer. Excess frost decreases the cooling performance of the refrigerator. Defrost the

refrigerator and freezer as necessary:

- Remove all food from the refrigerator.

- Turn the refrigerator OFF.

Defrosting the refrigerator makes excess water inside the refrigerator.

- Remove the drain hose from the drip cup at the rear of the refrigerator.

- Put the drain hose into a half-gallon or larger container to capture water.

- Put dry towels (etc.) inside the refrigerator and freezer to absorb melted frost.

High temperatures can cause the inside surfaces of the refrigerator to warp or melt. Do not use pans of

HOT water, a hair dryer, or any other high temperature devices to defrost the refrigerator. Do not use any

hard or sharp objects to remove frost. Damage to the interior of the refrigerator can occur.

- To increase the speed of defrosting, put pans of WARM water in the refrigerator and freezer.

- Remove the wet towels (etc.) and dry the interior.

- Remove the drain hose from the large container and put the drain hose back into the drip cup.

- Remove the large container from the enclosure.

- Start up the refrigerator.

- Allow the refrigerator to cool down.

- Return all food to the refrigerator.

NOTICE

CAUTION

Owner’s Manual 14

Interior:

Clean the inside of the refrigerator as often as necessary to avoid food odors:

- Remove all food from the refrigerator.

Do not use abrasive cleaners, chemicals, or scouring pads because they can damage the interior of the refrigerator.

- Wash the interior with a mild cleaner or a solution of liquid dish detergent and warm water.

- Rinse with a solution of baking soda and clean water.

- Dry with clean cloth.

- Put all food in the refrigerator.

Metal doors:

To clean the metal doors:

- Wash the doors with a mild cleaner or a solution of liquid dish detergent and warm water.

- Rinse with clean water.

- Dry with clean cloth.

Do not use abrasive cleaners, chemicals, or scouring pads because they can damage the metal doors.

Cleaning

NOTICE

Owner’s Manual 15

Ice Maker Storage

To prepare the ice maker for seasonal storage:

1. Close the vehicle water supply valve to the ice maker.

2. Push the ice maker arm up until it locks into the OFF position.

3. Remove the garden hose adapter from the water solenoid valve.

4. Remove the ice maker water line from the water solenoid valve

- Do not unwrap the water line heater wires from around the water solenoid valve.

5. Drain all of the water from both the water supply line and the ice maker water line.

6. Put the end of the water supply line, the end of the ice maker water line, and the water solenoid valve each into a clean plastic bag.

7. Use tape to close each plastic bag around the water lines and the water solenoid valve.

Door Sealing

Check the seal of the doors (See Art00980).

If a door does not seal correctly, excess frost will collect inside the refrigerator. Make sure the

doors seal correctly:

- Close each door on a piece of paper that is about the size and thickness of a dollar bill.

- Gently pull the paper.

- You should feel a slight drag between the gasket and the cabinet.

- Do this on all four sides of the door.

- If you do not feel a slight drag on the paper, the door does not seal correctly.

- Have your dealer or an authorized Norcold Service Center correct the seal of the door.

Refrigerator Storage

Before the refrigerator is stored for an extended (seasonal) period of time:

- Clean the interior of the refrigerator.

- Do not close the doors completely.

If the refrigerator is stored for an extended period of time, before start up:

- Make sure there are no obstructions in the vents, the ventilation air pathway, the burner, the orice, or the ue area.

Art00980

Owner’s Manual 16

Refrigerator Maintenance Checklist

Read and understand the following maintenance sections of this manual.

Norcold is not responsible for installation, adjustment, alteration, service, or maintenance performed by anyone other

than a qualied RV dealer or a Norcold authorized service center.

Have a qualied RV dealer or a Norcold authorized service center do these annual safety and maintenance checks:

- Examine the gas supply lines for leaks.

- Replace or repair if needed.

- Make sure the propane gas pressure is 11 inches water column.

- Adjust if needed.

- Make sure the combustion seal is complete and intact.

- Replace or repair it if needed.

- Make sure the burner and the burner orice are clean.

- Clean if needed.

- Make sure the electrode [167] is clean and the spark gap is 1/8 - 3/16 inch.(see Art02497)

- Adjust if needed.

- Make sure the AC voltage is 108 -132 volts and the DC voltage is 10.5 - 15.4 volts.

To use the ice maker after seasonal storage:

Do not operate the ice maker when the ambient air temperature is 0° F. or lower. Damage to the water

solenoid valve and the water supply line can occur.

1. Remove the tape and plastic bags from the end of the water supply line, the end of the ice maker water line, and the water solenoid

valve.

2. Connect the ice maker water line to the water solenoid valve.

3. Connect the garden hose adapter to the water solenoid valve.

4. Push the ice maker arm down into the ON position.

5. Open the vehicle water supply valve to the ice maker.

You should discard and not use the rst two batches of ice cubes. It will take about three cycles for the ice maker to

make fully formed and clean ice cubes.

CAUTION

NOTICE

Owner’s Manual 17

Refrigerator Maintenance

Gas ame appearance:

While in LP GAS operation, examine the appearance of the gas ame:

- Push the TEMP SET button until the number “9” appears in the center display.

- Open the lower intake vent.

The burner box cover can be hot. Wear gloves to avoid burns.

- Look at the gas ame [75] (See Art02497).

- The ame should be:

- a darker blue color on the inside of the ame and a lighter blue color on the

outside of the ame.

- a constant shape without ickering.

- Contact your dealer or Norcold authorized service center if the ame is:

- yellow

- ickering or changing shape.

- Make sure the ame does not touch the inside of the ue tube [76].

- If the ame touches the inside of the ue tube, contact your dealer or Norcold authorized service center.

- Close the burner box door.

Remove and clean the burner orice:

Your dealer or Norcold authorized service center must do this procedure.

Remove and clean the burner orice (See Art00956):

- Close the valve at the propane gas tank(s).

- Push the ON / OFF button to shut down the refrigerator.

- Open the lower intake vent.

The burner box cover can be hot. Wear gloves to avoid

burns.

- Remove the burner box cover by removing the screw(s).

To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line

connections.

- Remove the are nut from the orice assembly [77] (See Art00956).

- Remove the orice assembly from the burner [78].

Do not try to remove the orice [79] from the orice adapter [80] when cleaning. Removal will damage

the orice and seal of the orice and can cause a propane gas leak. Leaking propane gas can ignite or

explode which can result in dangerous personal injury or death. Do not clean the orice with a pin or

other objects.

Art 00956

77 78

CAUTION

WARNING

CAUTION

ART 02497

167

Owner’s Manual 18

Remove the Refrigerator

Your dealer or Norcold authorized service center must do this procedure.

The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the

refrigerator, be careful and wear cut resistant gloves.

To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the gas supply line

connections.

1. Close the valve at the propane gas tank(s).

2. Remove the black AC power cord and the white ice maker AC power cord (optional) from the receptacle.

3. Remove the DC wiring from the refrigerator:

- Put a mark on the DC wires so you can put them back in the correct location.

- Remove the DC fuse or remove the DC wiring from the battery or the converter.

- Remove the DC wires from the refrigerator.

4. Open the lower intake vent and remove the gas supply line from the bulkhead tting of the refrigerator.

5. Remove the top and bottom trim pieces by pulling them forward until they “snap” o of the refrigerator.

6. Remove the screws from the upper and lower mounting anges on the front of the refrigerator.

7. Remove the screws from the mounting ange at the rear of the refrigerator.

8. Remove the refrigerator from the opening.

- Clean the orice assembly with air pressure and alcohol only.

- Using a wrench, assemble the orice assembly to the burner.

- Assemble the are nut to the orice assembly.

- Examine all of the connections for gas leaks.

- Assemble the burner box cover.

CAUTION

WARNING

Owner’s Manual 19

Replacement Parts

You may purchase replacement parts through your local RV dealer or authorized Norcold Service Center.

Reinstall the Refrigerator

Your dealer or Norcold authorized service center must do this procedure.

Make sure the combustion seal is not broken, is completely around the refrigerator mounting anges, and

is between the mounting anges and the wall of the enclosure. If the combustion seal is not complete,

exhaust fumes can be present in the living area of the vehicle. The breathing of exhaust fumes can cause

dizziness, nausea, and in extreme cases, death.

1. Push the refrigerator completely into the enclosure.

2. Install the screws in the upper and then the lower mounting anges on the front of the refrigerator.

3. Install the screws in the mounting ange at the rear of the refrigerator.

4. Push the top and bottom trim pieces onto the to front of the refrigerator until they “snap” into position.

To avoid possible propane gas leaks, always use two wrenches to loosen and tighten the LP gas supply

line connections.

5. Attach the gas supply line to the bulkhead tting of the refrigerator.

6. Open the valve at the propane gas tank(s).

Do not allow the leak checking solution to touch the electrical components. Many liquids are electrically

conductive and can cause electrical shorts and in some cases, re.

7. Using a leak detecting solution, examine the gas supply line for leaks.

8. Connect the DC wiring to the refrigerator:

- Connect the DC wires to the refrigerator.

- Install the DC fuse or connect the DC wiring to the battery or the converter.

9. Connect the black AC power cord and the white ice maker AC power cord (optional) to the receptacle.

WARNING

Owner’s Manual 20

Fault Codes

“dr”

Audible alarm also.

“no” “FL”

Audible alarm also.

“no” “AC”

Audible alarm also.

“dc” “LO”

Audible alarm also.

“Sr”

Audible alarm also.

Temperature setting

ashes when TEMP SET

or MODE button is pushed.

“AC” “rE”

Audible alarm also.

“AC” “HE”

Audible alarm also.

“oP” “LI”

Audible alarm also.

“FL” “- -”

Audible alarm also.

Fault Code Meaning

The door was open for more

than 2 minutes.

The burner did not ignite or

re-ignite.

AC voltage is not available to

the refrigerator.

The DC voltage to the

refrigerator is low.

The DC voltage to the

refrigerator is low.

This is a fault within the

refrigerator controls.

The refrigerator is operating on

the Backup Operating System.

This is a fault within the

refrigerator controls.

This is problem related to the

AC heater.

A temperature limit switch is

open.

A ame is present at the burner

when there should be none.

Corrective Actions

Close the door.

Check:

- That the valve of the propane gas tank(s) is open.

- That the propane gas is at the correct pressure.

- That the manual shut o valve of the refrigerator is open.

- That there is no air in the propane gas supply line. See

“Removing air from the propane gas supply lines” section of

the Owner’s Manual.

- See your dealer or authorized Norcold Service Center.

Check:

- That the refrigerator is plugged into a serviceable outlet.

- That the fuse or circuit breaker or the vehicle is intact.

- That the vehicle generator is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Check:

- That the battery charging equipment of the vehicle is

operational.

- That the AC/DC converter is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Check:

- That the battery charging equipment of the vehicle is

operational.

- That the AC/DC converter is operational (if applicable).

- See your dealer or authorized Norcold Service Center.

Turn the refrigerator power OFF and then back on to reset.

If the Fault Code continues, see your dealer or authorized

Norcold Service Center.