DeWalt DW079KDT Le manuel du propriétaire

DW079

Rotary Laser

Laser rotatif

Láser rotativo

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

English

1

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS

OR ANY DEWALT TOOL, CALL US TOLL FREE AT:

1-800-4-DEWALT (1-800-433-9258).

WARNING! Read and understand all instructions.

Failure to follow all instructions listed below may result

in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Safety Instructions for Lasers

• Do not operate the laser in explosive atmospheres, such as

in the presence of flammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust or fumes.

• Use the laser only with the specifically designated batteries.

Use of any other batteries may create a risk of fire.

• Store idle laser out of reach of children and other untrained

persons. Lasers are dangerous in the hands of untrained

users.

• Use only accessories that are recommended by the

manufacturer for your model. Accessories that may be suitable

for one laser, may create a risk of injury when used on another

laser.

• Tool service MUST be performed only by qualified repair

personnel. Repairs, service or maintenance performed

by unqualified personnel may result in injury. To locate

your nearest DEWALT service center call 1-800-4-DEWALT

(1-800-433-9258) or go to http://www.dewalt.com on the Internet.

• Do not use optical tools such as a telescope or transit to

view the laser beam. Serious eye injury could result.

• Do not place the laser in a position which may cause anyone

to intentionally or unintentionally stare into the laser beam.

Serious eye injury could result.

• Do not position the laser near a reflective surface which

may reflect the laser beam toward anyone’s eyes. Serious

eye injury could result.

• Turn the laser off when it is not in use. Leaving the laser on

increases the risk of staring into the laser beam.

• Do not operate the laser around children or allow children

to operate the laser. Serious eye injury may result.

• Do not remove or deface warning labels. If labels are

removed user or others may inadvertently expose themselves to

radiation.

• Position the laser securely on a level surface. Damage to the

laser or serious injury could result if the laser falls.

• Dress properly. Do not wear loose clothing or jewelry.

Contain long hair. Keep your hair, clothing, and gloves away

from moving parts. Loose clothing, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and

should also be avoided.

WARNING: Use of controls or adjustments or performance

of procedures other than those specified herein may result in

hazardous radiation exposure.

WARNING! DO NOT DISASSEMBLE THE ROTARY LASER.

There are no user serviceable parts inside. Disassembling

the rotary laser will void all warranties on the product. Do not

modify the product in any way. Modifying the tool may result in

hazardous laser radiation exposure.

• The label on your tool may include the following symbols.

V .......volts nm .....wavelength in nanometers

mW .....milliwatts IIIa ..... Class IIIa Laser

.....laser warning symbol

English

2

FIG. 1 • For your convenience and safety, the following labels are on your

laser (Fig. 1).

AVOID EXPOSURE: LASER RADIATION IS EMITTED FROM

THIS APERTURES.

DANGER: LASER RADIATION. AVOID DIRECT EYE

EXPOSURE.

Laser Information

The DW079 Cordless Rotary Laser is listed as a CLASS IIIA LASER

PRODUCT and complies with the applicable requirement of title 21

of the Code of Federal Regulations set forth by: the Department of

Health, Education, and Welfare; the Food and Drug Administration;

the Center for Devices and Radiological Health.

These devices comply with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio and television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

English

3

• Connect the equipment into an outlet on a circuit differentfrom

that which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

These Class B digital devices comply with Canadian ICES-003.

SPECIFICATIONS

Light Source Semiconductor laser diode

Laser Wavelength 630 – 680 nm Visible

Laser Power <5mw, CLASS IIIa LASER

PRODUCT

Rotation Speed 0 – 600 rpm

Self-Leveling Range ± 5°

Indoor Visible Range 200' (61 m) diameter

Range with Detector 1500' (450 m) diameter

Level Accuracy ± 1/8" per 100' (± 3 mm per 31 m)

Power Source 9.6V–18V DEWALT batteries

Operating Temperature 23°F to 122°F (-5°C to 50°C)

Storage Temperature -4°F to 158°F (-20°C to 70°C)

Environmental Water resistant

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below.

Then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or dust.

Inserting or removing the battery from the charger may ignite the

dust or fumes.

• NEVER force battery pack into charger. DO NOT modify

battery pack in any way to fit into a non-compatible charger

as battery pack may rupture causing serious personal injury.

Consult the chart at the end of this manual for compatibility of

batteries and chargers.

• Charge the battery packs only in DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (40˚)

(such as outside sheds or metal buildings in summer).

DANGER: Electrocution hazard. Never attempt to open the

battery pack for any reason. If battery pack case is cracked or

damaged, do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that has

received a sharp blow, been dropped, run over or damaged in

any way (i.e., pierced with a nail, hit with a hammer, stepped on).

Electric shock or electrocution may result. Damaged battery packs

should be returned to service center for recycling.

NOTE: Battery storage and carrying caps are provided

for use whenever the battery is out of the tool or

charger. Remove cap before placing battery in charger

or tool.

WARNING: Fire hazard. Do not store or carry

battery so that metal objects can contact exposed

battery terminals. For example, do not place battery in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose nails,

screws, keys, etc. without battery cap. Transporting batteries can

possibly cause fires if the battery terminals inadvertently come

in contact with conductive materials such as keys, coins, hand

tools and the like. The US Department of Transportation Hazardous

English

4

Material Regulations (HMR) actually prohibit transporting batteries

in commerce or on airplanes (i.e., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits.

So when transporting individual batteries, make sure that the

battery terminals are protected and well insulated from materials

that could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR NICKEL CADMIUM

(NiCd) OR NICKEL METAL HYDRIDE (NiMH)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire.

• A small leakage of liquid from the battery pack cells may

occur under extreme usage or temperature conditions. This

does not indicate a failure.

However, if the outer seal is broken:

a. and the battery liquid gets on your skin, immediately wash

with soap and water for several minutes.

b. and the battery liquid gets into your eyes, flush them

with clean water for a minimum of 10 minutes and seek

immediate medical attention. (Medical note: The liquid is

25-35% solution of potassium hydroxide.)

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (LI-ION)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical attention is

needed, the battery electrolyte is composed of a mixture of liquid

organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs)

indicate that the costs to recycle these batteries (or

battery packs) at the end of their useful life have

already been paid by DEWALT. In some areas, it is

illegal to place spent nickel cadmium, nickel metal hydride or lithium

ion batteries in the trash or municipal solid waste stream and the

RBRC program provides an environmentally conscious alternative.

RBRC™ in cooperation with DEWALT and other battery users,

has established programs in the United States and Canada to

facilitate the collection of spent nickel cadmium, nickel metal

hydride or lithium ion batteries. Help protect our environment and

conserve natural resources by returning the spent nickel cadmium

and nickel cadmium, nickel metal hydride or lithium ion batteries

to an authorized DEWALT service center or to your local retailer

for recycling. You may also contact your local recycling center for

information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instruc tions for battery chargers.

English

5

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using battery

pack.

DANGER: Electrocution hazard. 120 volts are present at

charging terminals. Do not probe with conductive objects. Electric

shock or electrocution may result.

WARNING: Shock hazard. Do not allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

DEWALT rechargeable batteries. Other types of batteries may

burst causing personal injury and damage.

CAUTION: Under certain conditions, with the charger plugged

in to the power supply, the exposed charging contacts inside the

charger can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, steel wool, aluminum

foil, or any buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger before

attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging DEWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger.

This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire, electric shock, or electrocution.

• When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for out-

door use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that

is 16 gauge has more capacity than 18 gauge. An undersized

cord will cause a drop in line voltage resulting in loss of power

and overheating. When using more than one extension to make

up the total length, be sure each individual extension contains

at least the minimum wire size. The following table shows the

correct size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

smaller the gauge number, the heavier the cord.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.

7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m

Wire Size AWG

18 18 16 16 14 14 12

• Do not place any object on top of charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug.

English

6

• Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Using Automatic Tune-Up™ Mode

The Automatic Tune-Up™ Mode equalizes or balances the

individual cells in the battery pack allowing it to function at

peak capacity. Battery packs should be tuned up weekly or after

10 charge/discharge cycles or whenever the pack no longer

delivers the same amount of work. To use the Automatic Tune-

Up™, place the battery pack in the charger and leave it for at least

8 hours. The charger will cycle through the following modes.

1. The red light will blink continuously indicating that the 1-hour

charge cycle has started.

2. When the 1-hour charge cycle is complete, the light will stay

on continuously and will no longer blink. This indicates that the

pack is fully charged and can be used at this time.

3. If the pack is left in the charger after the initial 1-hour charge,

the charger will begin the Automatic Tune-Up™ mode. This

mode continues up to 8 hours or until the individual cells in the

battery pack are equalized. The battery pack is ready for use

and can be removed at any time during the Automatic Tune-

Up™ mode.

4. Once the Automatic Tune Up™ mode is complete, the charger

will begin a maintenance charge; the red indicator will remain

lit.

Chargers

Your tool uses a DEWALT 9.6, 12, 14.4, 18 Volt charger. Be sure to

read all safety instructions before using your charger. Consult the

chart at the end of this manual for compatibility of chargers and

battery packs.

Charging Procedure

DANGER: Electrocution hazard. 120 volts present at charging

terminals. Do not probe with conductive objects. Danger of electric

shock or electrocution.

1. Plug the charger into an appropriate outlet before inserting

battery pack.

2. Insert the battery pack into the charger, making sure the pack

is fully seated. The red (charging) light will blink continuously

indicating that the charging process has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may

be used at this time or left in the charger.

Indicator Light Operation

English

7

Charge Indicators

Some chargers are designed to detect certain problems that can

arise with battery packs. Problems are indicated by the red light

flashing at a fast rate. If this occurs, re-insert battery pack into

the charger. If the problem persists, try a different battery pack to

determine if the charger is OK. If the new pack charges correctly,

then the original pack is defective and should be returned to a

service center or other collection site for recycling. If the new battery

pack elicits the same trouble indication as the original, have the

charger tested at an authorized service center.

HOT/COLD PACK DELAY

Some chargers have a Hot/Cold Pack Delay feature: when the

charger detects a battery that is hot, it automatically starts a Hot

Pack Delay, suspending charging until the battery has cooled. After

the battery has cooled, the charger automatically switches to the

Pack Charging mode. This feature ensures maximum battery life.

The red light flashes long, then short while in the Hot Pack Delay

mode.

PROBLEM POWER LINE

Some chargers have a Problem Power Line indicator. When the

charger is used with some portable power sources such as

generators or sources that convert DC to AC, the charger may

temporarily suspend operation, flashing the red light with two

fast blinks followed by a pause. This indicates the power source

is out of limits.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the red

light glowing indefinitely. The charger will keep the battery pack

fresh and fully charged.

NOTE: A battery pack will slowly lose its charge when kept out of

the charger. If the battery pack has not been kept on maintenance

charge, it may need to be recharged before use. A battery pack may

also slowly lose its charge if left in a charger that is not plugged into

an appropriate AC source.

WEAK BATTERY PACKS: Chargers can also detect a weak

battery pack. Such batteries are still usable but should not be

expected to perform as much work. The charger will indicate to

replace battery pack.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65°F and

75°F (18° - 24°C). DO NOT charge the battery pack in an air

temperature below +40°F (+4.5°C), or above +105°F (+40.5°C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to touch while

charging. This is a normal condition, and does not indicate a

problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other

appliance

b. Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

c. Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F - 75°F

(18°- 24°C).

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

4. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously.

DO NOT CONTINUE to use under these conditions. Follow

English

8

the charging procedure. You may also charge a partially used

pack whenever you desire with no adverse affect on the battery

pack.

5. Under certain conditions, with the charger plugged into the

power supply, the exposed charging contacts inside the charger

can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, steel wool,

aluminum foil, or any buildup of metallic particles should be kept

away from charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity. Unplug

charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Never attempt to open the battery pack for any

reason. If the plastic housing of the battery pack breaks or cracks,

return to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from

direct sunlight and excess heat or cold.

2. Long storage will not harm the battery pack or charger. Under

proper conditions, they can be stored for 5 years or more.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

LASER OPERATION

• To extend battery life per charge, turn the laser off when it is not

in use.

• To ensure the accuracy of your work, check the laser

calibration often. Refer to Field Calibration Check under

Laser Maintenance.

• Before attempting to use the laser, make sure the tool is

positioned on a relatively smooth, secure surface.

• Always mark the center of the laser line or dot. If you mark

different parts of the beam at different times you will introduce

error into your measurements.

• To increase working distance and accuracy, set up the laser in

the middle of your working area.

• When attaching to a tripod or wall, mount the laser securely.

• When working indoors, a slow rotary head speed will produce

a visibly brighter line, a faster rotary head speed will produce a

visibly solid line.

• To increase beam visibility, wear Laser Enhancement Glass es

and/or use a Laser Target Card to help find the beam.

• Extreme temperature changes can cause movement or shifting

of building structures, metal tripods, equipment, etc., which can

effect accuracy. Check your accuracy often while working.

• When working with the DEWALT Digital Laser Detector, set the

laser’s rotation speed to the fastest setting.

• If the laser is dropped or has suffers a sharp blow, have the

calibration system checked by a qualified service center before

using the laser.

A

C

B

FIG. 2

English

9

Installing and Removing the

Battery Pack (Fig. 2)

NOTE: Make sure your battery pack is fully charged before you

install it.

INSTALLING THE BATTERY PACK

1. Release latch (B) to open the hatch door (A). Insert the battery

pack (C).

CAUTION: The laser will operate even if battery door is not

fully latched. To secure the battery, always ensure battery door

is closed and latched.

2. Slide the battery pack in firmly.

3. Close the hatch door and fasten latch.

REMOVING THE BATTERY PACK

1. Release latch to open the hatch door.

2. Remove the battery pack.

3. To recharge the battery pack, insert it into the charger as

described in the charger section of this manual.

Laser Control Panel

The laser is controlled by the power button (D), the speed/rotation

button (E), the scan mode button (F), and two arrows (G, H). The

arrows control the movement of the laser head left and right when

the laser is being used in the plumb mode. Four LED indicator lights

are on the control panel: power (I), X-axis leveling (J), Y-axis leveling

(K) and remote control private mode (L).

TURNING THE LASER ON (FIG. 3)

1. Insert the fully charged battery pack. Be sure that the battery

door is securely latched.

2. Gently press the power button (D) to power the laser on. The

power LED indicator light (J) will illuminate. If the laser is out of

level, the X-axis (J) and/or Y-axis (K) leveling lights will flash until

the laser is level. Press the speed/rotation button (E) to adjust

the rotation speed.

NOTE: The head will begin or resume rotation once the laser is

level.

KJ

I

H

G

F

E

DL

FIG. 3

TURNING THE LASER OFF

Gently press the power button to turn the laser off. The power LED

indicator light will no longer be illuminated.

Laser Control Panel Buttons

POWER BUTTON

To completely power the laser unit off, the power button on the

control panel of the laser unit must be pressed. The laser unit will

also automatically power off if it is left in Sleep Mode for 8 hours.

NOTE: Press the remote control power button to put the laser unit

into Sleep Mode. In Sleep Mode all laser unit functions shut off

except for a periodic blink from the power LED on the control panel

of the laser unit. Press the remote control power button again to

“wake up” the laser unit.

English

10

ARROW BUTTONS

The arrow buttons (G, H) are used for different functions depending

on the operating mode of the laser unit.

In Self-Leveling Horizontal Mode:

The arrows buttons adjust the direction of the laser beam in

Scan Mode or Pointing Mode (0 rpm).

In Self-Leveling Vertical Mode:

The arrow buttons move the laser beam left and right.

In Manual Mode:

The arrow buttons are used to tilt the laser head.

NOTE: Refer to Using the Wireless Remote Control for a full

description of Manual Mode.

SPEED/ROTATION BUTTON

The speed/rotation button (E) is used to adjust the rotation speed

of the laser beam through its 4 preset speeds.

The head speed will cycle through 4 speeds, then repeat the

sequence as the speed/rotation button is pressed.

REMEMBER:

Slow speed = Bright Beam Fast Speed = Solid Beam

NOTE: The speed/rotation button performs the same function as

the speed/rotation button on the remote control.

SCAN MODE BUTTON

The scan mode button (F) is used to make the laser head sweep

back and forth, creating a short, bright laser line. This short line is

much brighter and more visible than when the unit is in full rotation

mode.

Using Scan Mode:

To enter Scan Mode, push and release the scan mode

button. To exit Scan Mode, push and release the button

again.

The size and direction of the scan zone can be controlled

with the arrow buttons on the laser unit control panel or the

remote control. For a more detailed explanation, refer to

Using the Wireless Remote Control.

The size and direction of the scan zone can also be controlled

manually with the User Defined Scan Mode:

1. Set the laser unit at 0 rpm (pointer mode).

2. Manually rotate the laser head to position the laser beam

at one edge of the desired scan zone.

3. Press and hold the scan mode button on the laser unit

control panel. While holding down the scan mode button,

manually rotate the laser head to the opposite edge of the

desired scan zone.

4. Release the scan mode button.

5. The laser will scan between the two selected points.

NOTE: If the scan mode button is pressed and held, but the

laser head is not manually rotated, after four seconds the unit

will enter Private Mode or No Remote Mode as described

below.

IMPORTANT: The remote control cannot be used for User

Defined Scan Mode.

PUBLIC, PRIVATE AND NO REMOTE MODES

The DW079 Rotary Laser and the DW0794 Remote Control each

have the capability to operate in either Public Mode or Private

Mode. For the laser and the remote control to work together, they

must both be set to the same mode. The laser unit can also be set

to No Remote Mode, which causes it to ignore all remote control

commands.

Public Mode

The laser unit can receive commands from any DEWALT

laser remote control, and even from some other brands of

English

11

laser remote controls. This is the normal, default operating

mode for the DW079 laser unit.

To Activate Public Mode:

• Press and hold the speed/rotation button (E) (open

padlock symbol beside the button).

• As the default operating mode, the laser unit will power

up in Public Mode if:

• The laser was last used in Public Mode

OR

• The laser has been turned off for 8 hours after being

used in Private Mode

OR

• The battery pack has been removed and reinstalled.

Private Mode

The laser unit will only accept commands from the

DW0794 remote control designated by the user.

To activate Private Mode:

• Press and hold the scan mode button (F) on the laser

unit control panel (closed padlock symbol) and at the

same time press and hold the remote control scan

mode button (R) (closed padlock symbol).

After 4 seconds, both the laser unit and the remote

control will enter Private Mode. As confirmation,

the laser unit will beep and the laser control panel

LED (L) (next to the closed padlock symbol) and the

remote control LED (T) (next to the closed padlock

symbol) will flash.

No Remote Mode

This mode causes the laser unit to ignore all remote

control commands.

To activate No Remote Mode:

• Press and hold the scan mode button (F) on the laser

unit control panel (closed padlock symbol), but do

not press any button on the remote control.

After 4 seconds, the laser unit will beep and the LED

(L) next to the padlock symbol will flash.

Using the Wireless FIG. 4 S

M

P

O

N

RQ

T

Remote Control (Fig. 4)

The remote control allows one person

to operate and setup the laser from a

distance. The remote control features a

power button (M), manual mode button

(N), four arrows (O, PP), speed/rotation

button (Q) and scan mode button (R).

Two LED indicator lights are on the

remote control: transmit (S) and private

mode (T).

REMOTE CONTROL: POWER

BUTTON

Press the remote control power button

(M) to put the laser unit into Sleep

Mode. In Sleep Mode all laser unit functions shut off except for a

periodic blink from the power LED (L) on the control panel of the

laser unit. Press the remote control power button again to “wake

up” the laser unit.

NOTE: To completely power the laser unit off, the power button on

the control panel of the laser unit must be pressed. The laser unit will

also automatically power off if it is left in Sleep Mode for 8 hours.

REMOTE CONTROL: MANUAL MODE BUTTON

To activate Manual Mode, press and hold the remote control manual

mode button (N) for 3 seconds. Manual Mode must be activated to

English

12

use manual sloping. (Refer to Using Manual Slope Mode for a

complete description of this function.)

To re-engage full self-leveling, press and hold the manual mode

button again for 3 seconds.

Using Manual Slope Mode:

The DW079 Manual Slope Mode allows the self-leveling

function to be disabled in one axis (direction) so that the

laser can be sloped in that axis. The other axis will continue

to self-level, ensuring that the laser beam is only sloping in

the expected direction.

Entering and exiting Manual Slope Mode:

• To activate Manual Slope Mode, press and hold the

remote control manual mode button (N) for 3 seconds.

• To re-engage full self-leveling, press and hold the

manual mode button again for 3 seconds.

Setting the Slope Direction:

• When Manual Slope Mode is activated, the unit auto-

matically engages Manual Y Mode. This allows the

operator to slope the laser in the direction of the Y-axis,

as indicated by the “gunsights” on the rollcage.

In certain situations, it may be desirable to slope the

laser in the X-axis. The direction of Manual Slope Mode

can be changed back and forth between the Y- and

X-axes as follows:

• Immediately (within 5 seconds) after entering Manual

Slope Mode, press and hold the remote control right

arrow button to activate Manual X Mode.

• The unit can be changed back to Manual Y Mode by

immediately pressing and holding the remote control

left arrow button.

• To change the direction of Manual Slope Mode at a

later time, re-engage full self-leveling, then activate

Manual Slope Mode again and go through the axis

selection procedure outlined above.

The X and Y LED indicator lights on the laser unit control

panel (Fig. 3, K, J) will indicate the manual slope direction

that is selected. The manually controlled axis is identified

by a turned-off LED, and the self-leveling axis is identified

by a lighted LED.

Setting the Amount of Slope:

Once Manual Slope Mode is activated, the amount of

slope can be manually adjusted using any of the following

methods:

• Use the laser control panel up and down arrow buttons

(Fig. 3, G, H) to tilt the laser rotor head up and down.

OR

• Use the remote control up and down arrow buttons

(Fig. 3, O) to tilt the laser rotor head up and down.

OR

• The entire laser unit can be tipped up and down by

setting it on a sloped surface. Make sure the laser unit is

positioned so the direction of manual sloping is lined up in

the same direction as the sloped surface.

REMOTE CONTROL: ARROW BUTTONS

The arrow buttons (O, P) are used for different functions depending

on the operating mode of the laser unit.

In Self-Leveling Horizontal Mode:

The up and down arrows (O) adjust the length of the laser line

in Scan Mode.

The left and right arrows (P) adjust the direction of the laser

beam in Scan Mode or Pointing Mode (0 rpm).

In Self-Leveling Vertical Mode:

The up and down arrows (O) adjust the position of the laser

line in Scan Mode.

English

13

The left and right arrows (P) move the laser beam left and

right.

In Manual Mode:

The arrow buttons (O) are used to tilt the laser head up or

down in the X or Y directions as marked on the protective roll

cage of the laser unit.

REMOTE CONTROL: SPEED/ROTATION BUTTON

The speed/rotation button (Q) is used to adjust the speed of the

laser beam through its 4 preset speeds.

NOTE: The speed/rotation button performs the same function as

the speed/rotation button on the control panel of the laser unit.

REMOTE CONTROL: SCAN MODE BUTTON

The scan mode button (R) is used to make the laser head sweep

back and forth, creating a short, bright laser line. This short line is

much brighter and more visible than when the unit is in full rotation

mode.

Using Scan Mode:

To enter Scan Mode, push and release the scan mode button.

To exit Scan Mode, push and release the button again.

The size and direction of the scan zone can be controlled

with the arrow buttons on the laser unit control panel or the

remote control. For a more detailed explanation, refer to

Arrow Buttons under Laser Control Panel Buttons.

IMPORTANT: The remote control cannot be used for User

Defined Scan Mode.

REMOTE CONTROL: PUBLIC AND PRIVATE MODE

The DW079 Rotary Laser and the DW0794 Remote Control each

have the capability to operate in either Public Mode or Private

Mode. For the laser and the remote control to work together, they

must both be set to the same mode.

Public Mode

The remote control sends signals that can potentially be

received by multiple laser units as well as other models of

laser units. This is the normal, default operating mode for the

DW0794 remote control.

To activate Public Mode:

• Press and hold the speed/rotation button (Q) (open

padlock symbol beside the button) for 4 seconds.

• After an 8-hour period of inactivity, the remote control

will automatically enter Public Mode.

• After replacement of its battery, the remote control will

automatically enter Public Mode.

Private Mode

The remote control sends signals that can only be received by

the designated laser unit.

To activate Private Mode:

• Press and hold the remote control scan mode button

(R) (closed padlock symbol beside the button) and at

the same time, press and hold the scan mode button

(F) on the laser unit control panel (closed padlock

symbol).

After 4 seconds, both the remote control and the laser

unit will enter Private Mode. As confirmation, the laser

unit will beep and the laser unit control panel LED (L)

(next to the closed padlock symbol) and the remote

control LED (T) (next to the closed padlock symbol) will

flash.

Height of Instrument Alert

The DW079 has a built-in alarm feature that alerts the operator if

the unit is disturbed after the unit has self-leveled. The laser unit will

stop rotating, the control panel LED indicator lights will flash and the

beeper will sound.

English

14

TO RESET THE LASER UNIT FOR CONTINUED USE

• Turn the unit off and back on again using the power button on

the laser unit control panel.

OR

• Put the unit in sleep mode and then wake it back up using the

power button on the remote control.

NOTE: Always recheck the laser setup after the Height of

Instrument Alert has triggered.

Laser Troubleshooting

LASER AND REMOTE CONTROL ARE OUT OF SYNC

• On the remote control, press and hold speed/rotation button for

4 seconds to activate Public Mode.

• On the laser unit, press and hold speed/rotation button for

4 seconds to activate Public Mode.

Using the Laser on a Tripod

1. Position the tripod securely and set it to the desired height.

2. Make sure that the top of the tripod is roughly level. The laser

will self-level only if the top of the tripod is within ± 5˚ of level. If

the laser is set up too far out of level, it will beep when it reaches

the limit of its leveling range. No damage will be done to the

laser, but it will not operate in an “out of level” condition.

3. Secure the laser to the tripod by screwing the threaded knob on

the tripod into the female thread on the bottom of the laser.

NOTE: Be sure that the tripod you are working with has a

5/8"–11 threaded screw to ensure secure mounting.

4. Turn the laser on and adjust the rotation speed and controls as

desired.

Using the Laser on a Floor (Fig. 5)

The laser level can be positioned directly on the floor for leveling

and plumbing applications such as framing walls.

1. Place the laser on a relatively smooth and level surface where

it will not be disturbed.

2. Position the laser for a level or plumb setting as shown.

3. Turn the laser on and adjust the rotation speed and controls as

desired.

LEVEL

MODE

PLUMB

MODE

FIG. 5

NOTE: The laser will be easier to set up for wall applications if the

rotation speed is set to 0 rpms and if the remote control is used to

line up the laser with control marks. The remote allows one person

to set up the laser.

Manual Head Rotation

The laser is designed with a protective alloy cage around the rotary

head to prevent accidental damage from work site activities. You

can still access the rotary head and manually direct the beam to

establish or transfer a mark.

Laser Accessories

Recommended accessories for use with your tool are available for

purchase at your factory-owned local service center.

WARNING: Since accessories, other than those offered by

DEWALT, have not been tested with this product, use of such

English

15

accessories with this tool could be hazardous. To reduce the risk

of injury, only DEWALT, recommended accessories should be used

with this product.

If you need assistance in locating any accessory, please contact

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD

21286, call 1-800-4-DEWALT (1-800-433-9258) or visit our website

www.dewalt.com

Laser Enhancement Glasses

Some laser kits include a pair of FIG. 6

Laser En hancement Glasses (Fig. 6).

These red lens glasses improve the

visibility of the laser beam under

bright light conditions or over long

distances when the laser is used for

interior applications. These glasses

are not required to operate the laser.

CAUTION: These glasses are not ANSI approved safety glasses

and should not be worn while operating other tools. These glasses

do not keep the laser beam from entering your eyes.

DANGER: TO REDUCE THE RISK OF SERIOUS PERSONAL

INJURY, NEVER STARE DIRECTLY INTO THE LASER BEAM,

WITH OR WITHOUT THESE GLASSES.

Target Card

Some laser kits include a Laser Target Card

FIG. 7

(Fig. 7) to aid in locating and marking the laser

beam. The target card enhances the visibility of the

laser beam as the beam crosses over the card. The

card is marked with standard and metric scales.

The laser beam passes through the red plastic and

reflects off of the reflective tape on the reverse side.

The magnet at the top of the card is designed to

hold the target card to ceiling track or steel studs to determine

plumb and level positions. For best performance when using the

Target Card, the DEWALT logo should be facing you.

Digital Laser Detector: DW0772

(Fig. 8–10)

Some laser kits include a DEWALT Digital Laser Detector. The

DEWALT Digital Laser Detector allows you to locate a laser beam

emitted by a rotary laser in bright light conditions or over long

distances. The detector can be used in both indoor and outdoor

situations where it is difficult to see the laser beam.

DD

X

W

AA

Z

V

U

FIG. 8

The detector is not for use with non-rotating lasers but is compatible

with most rotary red-beam or infrared (invisible) beam lasers on the

market. It can be set to indicate the location of the beam to either

the nearest 1/8" (3 mm) or the nearest 1/25" (1 mm). The detector

gives both visual signals through the display window (V) and audio

signals through the speaker (W) to indicate the location of the laser

beam.

English

16

The DEWALT Digital Laser Detector can be used with or without

the detector clamp. When used with the clamp, the detector can be

positioned on a grade rod, leveling pole, stud or post.

BATTERIES (FIG. 9)

X

Y

FIG. 9

The Digital Laser Detector is powered by a

9 volt battery. To install the battery pro-

vided, lift up on the battery compartment

cover (X). Place the 9 volt battery in

the compartment, aligning the battery as

shown on the embossed icon (Y).

DETECTOR CONTROLS (FIG. 10)

The detector is controlled by the power/

volume button (Z) and the accuracy mode

button (AA).

When the power/volume button is pushed

CC

BB

AA2

AA1

FIG. 10

once, the detector is turned on. The top of

the display window shows the ON icon

(BB), and the volume icon (CC). To

decrease the volume of the audible signal

that the detector emits when it senses a

laser beam, push the button again; one of

the half circles next to the horn icon will

dissappear. To turn off the audible signal

push the button a third time; the volume

icon will dissapear. The DEWALT Digital

Laser Detector also has an auto shut-off

feature. If a rotary laser beam does not strike the beam detection

window, or if no buttons are pressed, the detector will shut itself off

in about 30 minutes.

When the detector is on, the bottom of the window shows an

accuracy mode icon. Either the ±1/25" (1 mm) accuracy mode icon

(AA1) will appear, or the ±1/8" (3 mm) accuracy mode icon (AA2)

will appear. When the ±1/25" (1 mm) accuracy mode icon appears,

it indicates that the detector will give an “on grade” reading only

when the laser beam is on grade or no more than 1/25" (1 mm)

above or below it. When the 1/8" (3 mm) accuracy mode icon

appears, it indicates that the detector will give an “on grade”

reading when the laser beam is on grade or approximately 1/8"

(3 mm) above or below it. Push the accuracy mode button (AA)

once to change the accuracy mode.

Detector Operation (Fig. 11)

1. Set up and position the rotary laser that you will be using

according to the manufacturer’s directions. Turn the laser on and

make sure that the laser is rotating and emitting a laser beam.

Slightly Slightly

Above Above On Below Below

Grade Grade Grade Grade Grade

fast fast steady slow slow

beep beep tone beep beep

audible

signals

INDICATORS

display icons

FIG. 11

NOTE: This detector has been designed to be used only with a

rotating laser. The detector will not work with a stationary beam

laser level.

2. Turn the detector on by pressing the power/volume button (Z).

English

17

3. Adjust the volume as desired as described in the Detector

Controls.

4. Position the detector so that the detector window (U) is facing

the laser beam produced by the rotary laser. Move the detector

up or down within the approximate area of the beam, until you

have centered the detector. For information about the display

window indicators and the audible signal indicators, refer to

the table titled Indicators (Fig. 11).

5. Use the marking notches (DD) to accurately mark the position

of the laser beam.

II

JJ

HH

GG

FF

EE

FIG. 12

DD

MOUNTING ON A GRADE ROD (FIG. 12)

1. To secure your detector to a grade rod, first attach the detector

to the clamp by pushing in on the clamp latch (EE). Slide the

tracks (FF) on the clamp around the rail (GG) on the detector

until the latch (HH) on the clamp pops into the latch hole (II) on

the detector.

2. Open the jaws of the clamp by turning the clamp knob (JJ)

counterclockwise.

3. Position the detector at the height needed and turn the clamp

knob clockwise to secure the clamp on the rod.

4. To make adjustments in height, slightly loosen the clamp,

reposition and retighten.

Detector Cleaning and Storage

• Dirt and grease may be removed from the exterior of the

detector using a cloth or soft, non-metallic brush.

• The DEWALT Digital Laser Detector is waterproof. If you should

drop the detector in mud, wet concrete, or a similar substance,

simply hose the detector off. Do not use high pressure water,

e.g., from a pressure washer.

• The best storage place is one that is cool and dry–away from

direct sunlight and excess heat or cold.

Detector Service

Except for batteries, there are no user serviceable parts in the

Digital Laser Detector. Do not disassemble the unit. Unauth orized

tampering with the laser detector will void all warranties.

Detector Troubleshooting

THE DETECTOR WILL NOT TURN ON.

• Press and release the power/volume button.

• Check to see that the battery is in place and in the proper

position.

• If the detector is very cold, allow it to warm up in a heated

area.

• Replace the 9 volt battery. Turn the unit on.

• If the detector still does not turn on, take the detector to a

DEWALT service center.

THE DETECTOR’S SPEAKER MAKES NO SOUND.

• Ensure that the detector is on.

English

18

• Press the power/volume button. It will toggle from high, to low,

to mute.

• Ensure that the rotary laser is spinning and that it is emitting a

laser beam.

• If the detector is still not making any sound, take it to a DEWALT

service center.

THE DETECTOR DOES NOT RESPOND TO A STATIONARY

LASER BEAM.

• The DEWALT Digital Laser Detector has been designed to work

only with rotary lasers.

THE DETECTOR GIVES OFF A TONE BUT THE LCD

DISPLAY WINDOW DOES NOT FUNCTION.

• If the detector is very cold, allow it to warm up in a heated

area.

• If the LCD display window is still not functioning, take the

detector to a DEWALT service center.

Construction Grade Rod

DANGER: NEVER attempt to use a grade rod in a storm or

near overhanging electric wires. Death or serious personal injury

will occur.

Some laser kits include a grade rod. The DEWALT FIG. 13

Grade Rod is marked with measurement scales

on both sides and is constructed in telescoping

sections. A spring-loaded button actuates a lock to

hold the grade rod at various lengths.

The front of the grade rod has the measurement

scale starting at the bottom. Use this for measuring

from the ground up when grading or leveling jobs.

The back of the grade rod is designed to measure

the height of ceilings, joists, etc. Fully extend the

top section of the grade rod until the button locks into the previous

section. Extend that section either until it locks into the adjacent

section or until the grade rod touches the ceiling or joist. The height

is read where the last extended section exits the previous lower

section, as shown in Figure 13.

Using the Laser with a Wall Mount

(Fig. 14, 15)

Some laser kits include a Wall Mount. It can be used for attaching

the tool to track or ceiling angle and to aid in acoustical ceiling

installation. Follow the directions below for using the wall mount.

CAUTION: Before attaching the laser level to wall track or ceiling

angle, be sure that the track or angle is properly secured.

1. Place the laser on the mounting base (KK) aligning the hole (LL)

on the bottom of the laser with the hole (MM) in the mounting

base. Turn the mounting knob (NN) to secure the laser.

PP

QQ

LL

SS

RR

NN

OO

PP

MM

KK

FIG. 14

La page est en cours de chargement...

DeWalt DW079KDT Le manuel du propriétaire

DeWalt DW079KDT Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents