DeWalt Laser Level DW076 Manuel utilisateur

Marque: DeWalt

Modèle: Laser Level DW076

Taper: Manuel utilisateur

Ce manuel convient également à

DW076

Rotary Laser

Laser rotatif

Láser rotativo

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO

ANTES DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

English

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS

OR ANY D

EWALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

EWALT (1-800-433-9258)

WARNING! Read and understand all instructions.

Failure to follow all instructions listed below may result

in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

Safety Instructions for Lasers

• Do not operate the laser in explosive atmospheres, such as

in the presence of flammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust or fumes.

• Use the laser only with the specifically designated batteries.

Use of any other batteries may create a risk of fire.

• Store idle laser out of reach of children and other untrained

persons. Lasers are dangerous in the hands of untrained users.

• Use only accessories that are recommended by the manu-

facturer for your model. Accessories that may be suitable for

one laser, may create a risk of injury when used on another laser.

• Tool service must be performed only by qualified repair

personnel. Service or maintenance performed by unquali-

fied personnel may result in injury. To locate your nearest

WALT service center call 1-800-4-D

WALT (1-800-433-9258)

or go to http://www.dewalt.com on the Internet.

• Do not use optical tools such as a telescope or transit to

view the laser beam. Serious eye injury could result.

• Do not place the laser in a position which may cause any-

one to intentionally or unintentionally stare into the laser

beam. Serious eye injury could result

• Turn the laser off when it is not in use. Leaving the laser on

increases the risk of staring into the laser beam.

• Repairs and servicing MUST be performed by a qualified

repair facility. Repairs performed by unqualified personnel

could result in serious injury.

• Do not disassemble the laser tool. There are no user service-

able parts inside.

• Do not operate the laser around children or allow children

to operate the laser. Serious eye injury may result.

• Do not remove or deface warning labels. If labels are

removed user or others may inadvertently expose themselves to

radiation.

• Position the laser securely on a level surface. Damage to the

laser or serious injury could result if the laser falls.

• Dress properly. Do not wear loose clothing or jewelry.

Contain long hair. Keep your hair, clothing, and gloves

away from moving parts. Loose clothing, jewelry, or long hair

can be caught in moving parts. Air vents often cover moving

parts and should also be avoided.

CAUTION - Use of controls or adjustments or performance

of procedures other than those specified herein may result in

hazardous radiation exposure.

WARNING! DO NOT DISASSEMBLE THE ROTARY LASER.

There are no user serviceable parts inside. Disassembling the

rotary laser will void all warranties on the product. Do not

modify the product in any way. Modifying the tool may result in

hazardous laser radiation exposure.

• The label on your tool may include the following symbols.

V......................volts

mW ................milliwatts

..............laser warning symbol

nm ..................wavelength in nanometers

IIIa ..................Class IIIa Laser

English

• For your convenience and safety, the following labels are on

your laser.

AVOID EXPOSURE: LASER RADIATION IS EMITTED FROM

THIS APERTURES.

DANGER: LASER RADIATION. AVOID DIRECT EYE

EXPOSURE.

Laser Information

The DW076 Cordless Rotary Laser is listed as a CLASS IIIA

LASER PRODUCT and complies with the applicable requirement

of title 21 of the Code of Federal Regulations set forth by: the

Department of Health, Education, and Welfare; the Food and Drug

Administration; the Center for Devices and Radiological Health.

These devices comply with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause unde-

sired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio and television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit differentfrom

that which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

These Class B digital devices comply with Canadian ICES-003.

Important Safety Instructions for

Battery Packs

Your tool uses a 9.6, 12.0, 14.4 or an 18 Volt DEWALT battery pack.

When ordering replacement battery packs, be sure to include cata-

log number and voltage. Extended Run-Time battery packs deliver

more run-time than standard battery packs. Consult the chart at the

end of this manual for compatibility of chargers and battery packs.

NOTE: Your tool will accept either standard or Extended Run Time

battery packs. However, be sure to select proper voltage. Batteries

slowly lose their charge when they are not on the charger, the best

place to keep your battery is on the charger at all times.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below.

Then follow charging procedures outlined.

English

READ ALL INSTRUCTIONS

• Do not incinerate the battery pack even if it is severely dam-

aged or is completely worn out. The battery pack can explode

in a fire.

• A small leakage of liquid from the battery pack cells may

occur under extreme usage or temperature conditions. This

does not indicate a failure. However, if the outer seal is broken

and this leakage gets on your skin:

a. Wash quickly with soap and water.

b. Neutralize with a mild acid such as lemon juice or vinegar.

c. If battery liquid gets into your eyes, flush them with clean

water for a minimum of 10 minutes and seek immediate

medical attention. (MEDICAL NOTE: The liquid is 25-35%

solution of potassium hydroxide.)

• Charge the battery packs only in D

WALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (40˚)

(such as outside sheds or metal buildings in summer).

DANGER: Electrocution hazard. Never attempt to open the bat-

tery pack for any reason. If battery pack case is cracked or dam-

aged, do not insert into charger. Electric shock or electrocution may

result. Damaged battery packs should be returned to service cen-

ter for recycling.

NOTE: Battery storage and carrying caps are provided

for use whenever the battery is out of the tool or charg-

er. Remove cap before placing battery in charger or tool.

WARNING: Fire hazard. Do not store or carry

battery so that metal objects can contact exposed

battery terminals. For example, do not place battery

in aprons, pockets, tool boxes, product kit boxes, drawers, etc., with

loose nails, screws, keys, etc. without battery cap. Transporting

batteries can possibly cause fires if the battery terminals

inadvertently come in contact with conductive materials such

as keys, coins, hand tools and the like.

The US Department of

Transportation Hazardous Material Regulations (HMR) actually

prohibit transporting batteries in commerce or on airplanes (i.e.,

packed in suitcases and carry-on luggage) UNLESS they are

properly protected from short circuits. So when transporting indi-

vidual batteries, make sure that the battery terminals are protected

and well insulated from materials that could contact them and

cause a short circuit.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling

Corporation) Seal on the nickel-cadmium battery (or

battery pack) indicates that the costs to recycle the bat-

tery (or battery pack) at the end of its useful life have

already been paid by D

EWALT. In some areas, it is ille-

gal to place spent nickel-cadmium batteries in the trash or municipal

solid waste stream and the RBRC program provides an environ-

mentally conscious alternative.

RBRC in cooperation with D

EWALT and other battery users, has

established programs in the United States to facilitate the collection

of spent nickel-cadmium batteries. Help protect our environment

and conserve natural resources by returning the spent nickel-

cadmium battery to an authorized D

EWALT service center or to your

local retailer for recycling. You may also contact your local recycling

center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the

Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety instructions for battery chargers.

• Before using charger, read all instructions and cautionary mark-

ings on charger, battery pack, and product using battery pack.

English

DANGER: Electrocution hazard. 120 volts are present at charg-

ing terminals. Do not probe with conductive objects. Electric shock

or electrocution may result.

WARNING: Shock hazard. Do not allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

WALT nickel cadmium rechargeable batteries. Other types of

batteries may burst causing personal injury and damage.

CAUTION: Under certain conditions, with the charger plugged in

to the power supply, the exposed charging contacts inside the

charger can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, steel wool, aluminum

foil, or any buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger before

attempting to clean.

• DO NOT attempt to charge the battery pack with any charg-

ers other than the ones in this manual. The charger and bat-

tery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

WALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger.

This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

• Do not use an extension cord unless it is absolutely neces-

sary. Use of improper extension cord could result in risk of fire,

electric shock, or electrocution.

• An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. When using more

than one extension to make up the total length, be sure each

individual extension contains at least the minimum wire size.

Recommended Minimum Wire Size for Extension Cords

Total Length of Cord

25 ft. 50 ft. 75 ft. 100 ft. 125 ft. 150 ft. 175 ft.

7.6 m 15.2 m 22.9 m 30.5 m 38.1 m 45.7 m 53.3 m

Wire Size AWG

18 18 16 16 14 14 12

• Do not place any object on top of charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charg-

er in a position away from any heat source. The charger is ven-

tilated through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug — have

them replaced immediately.

• Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble charger; take it to an authorized service

center when service or repair is required. Incorrect reassem-

bly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard household

electrical power (120 Volts). Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

English

Using Automatic Tune-Up™ Mode

The Automatic Tune-Up™ Mode equalizes or balances the individ-

ual cells in the battery pack allowing it to function at peak capacity.

Battery packs should be tuned up weekly or after 10 charge/dis-

charge cycles or whenever the pack no longer delivers the same

amount of work. To use the Automatic Tune-Up™, place the battery

pack in the charger and leave it for at least 8 hours. The charger

will cycle through the following modes.

1. The red light will blink continuously indicating that the 1-hour

charge cycle has started.

2. When the 1-hour charge cycle is complete, the light will stay on

continuously and will no longer blink. This indicates that the

pack is fully charged and can be used at this time.

3. If the pack is left in the charger after the initial 1-hour charge,

the charger will begin the Automatic Tune-Up mode. This mode

continues up to 8 hours or until the individual cells in the battery

pack are equalized. The battery pack is ready for use and can

be removed at any time during the Tune-Up mode.

4. Once the Automatic Tune Up mode is complete, the charger will

begin a maintenance charge; the red indicator will remain lit.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

Chargers

Your tool uses a DEWALT charger. Your battery can be charged in

EWALT 1 Hour Chargers, 15 Minute Chargers or Vehicular 12 Volt

Charger. Be sure to read all safety instructions before using

your charger. Consult the chart at the end of this manual for

compatibility of chargers and battery packs.

Charging Procedure

DANGER: Electrocution hazard. 120 volts present at charging

terminals. Do not probe with conductive objects. Danger of electric

shock or electrocution.

1. Plug the charger into an appropriate outlet before inserting

battery pack.

2. Insert the battery pack into the charger, making sure the pack

is fully seated. The red (charging) light will blink continuously

indicating that the charging process has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may

be used at this time or left in the charger.

Indicator Light Operation

Charge Indicators

Some chargers are designed to detect certain problems that can

arise with battery packs. Problems are indicated by the red light

flashing at a fast rate. If this occurs, re-insert battery pack into the

charger. If the problem persists, try a different battery pack to deter-

mine if the charger is OK. If the new pack charges correctly, then the

original pack is defective and should be returned to a service center

or other collection site for recycling. If the new battery pack elicits the

same trouble indication as the original, have the charger tested at

an authorized service center.

HOT/COLD PACK DELAY

Some chargers have a Hot/Cold Pack Delay feature: when the

charger detects a battery that is hot, it automatically starts a Hot

Pack Delay, suspending charging until the battery has cooled.

After the battery has cooled, the charger automatically switches

to the Pack Charging mode. This feature ensures maximum

English

battery life. The red light flashes long, then short while in the Hot

Pack Delay mode.

PROBLEM POWER LINE

Some chargers have a Problem Power Line indicator. When the

charger is used with some portable power sources such as genera-

tors or sources that convert DC to AC, the charger may temporarily

suspend operation, flashing the red light with two fast blinks fol-

lowed by a pause. This indicates the power source is out of limits.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the red

light glowing indefinitely. The charger will keep the battery pack

fresh and fully charged.

NOTE: A battery pack will slowly lose its charge when kept out of

the charger. If the battery pack has not been kept on maintenance

charge, it may need to be recharged before use. A battery pack

may also slowly lose its charge if left in a charger that is not plugged

into an appropriate AC source.

WEAK BATTERY PACKS: Chargers can also detect a weak bat-

tery. Such batteries are still usable but should not be expected to

perform as much work. In such cases, about 10 seconds after bat-

tery insertion, the charger will beep rapidly 8 times to indicate a

weak battery condition. The charger will then go on to charge the

battery to the highest capacity possible.

Important Charging Notes

1. Longest life and best performance can be obtained if the bat-

tery pack is charged when the air temperature is between 65°F

and 75°F (18°- 24°C). DO NOT charge the battery pack in an

air temperature below +40°F (+4.5°C), or above +105°F

(+40.5°C). This is important and will prevent serious damage to

the battery pack.

2. The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery pack

after use, avoid placing the charger or battery pack in a warm

environment such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check current at receptacle by plugging in a lamp or other

appliance

b. Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

c. Move charger and battery pack to a location where the

surrounding air temperature is approximately 65°F - 75°F

(18°- 24°C).

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

4. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse affect on the battery pack.

5. Under certain conditions, with the charger plugged into the

power supply, the exposed charging contacts inside the charg-

er can be shorted by foreign material. Foreign materials of a

conductive nature such as, but not limited to, steel wool, alu-

minum foil, or any buildup of metallic particles should be kept

away from charger cavities. Always unplug the charger from the

power supply when there is no battery pack in the cavity.

Unplug charger before attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

charger. Electric shock may result.

English

CAUTION: Never attempt to open the battery pack for any rea-

son. If the plastic housing of the battery pack breaks or cracks,

return to a service center for recycling.

LASER OPERATION

• Ensure that the battery is properly charged. If the “Power” LED

light is flashing, the battery needs to be charged.

• To extend battery life per charge, turn the laser off when it is not

in use.

• To ensure the accuracy of your work, check the laser calibration

often. See the Field Calibration Check section of this manual.

• Before attempting to use the laser, make sure the tool is posi-

tioned on a relatively smooth,secure surface.

• Always mark the center of the laser line or dot. If you mark dif-

ferent parts of the beam at different times you will introduce

error into your measurements.

• To increase working distance and accuracy, set up the laser in

the middle of your working area.

• When attaching to a tripod or wall, mount the laser securely.

• When working indoors, a slow rotary head speed will produce

a visibly brighter line, a faster rotary head speed will produce a

visibly solid line.

• To increase beam visibility, wear a Laser Enhancement

Glasses (not included) and/or use a Laser Target Card (not

included) to help find the beam.

• Extreme temperature changes can cause movement or shifting

of building structures, metal tripods, equipment, etc., which can

effect accuracy. Check your accuracy often while working.

• If the laser is dropped or has suffers a sharp blow, have the

calibration system checked by a qualified service center before

using the laser.

NOTE: The DW076 rotary laser has no remote control capability.

Installing and Removing the

Battery Pack

NOTE: Make sure your battery pack is fully

charged before you install it.

INSTALLING THE BATTERY PACK

1. Rotate the battery adapter plate (A) so that the

applicable cut out for 9.6, 12, 14.4 volt pack

or the 18 volt pack is aligned with the battery

contacts facing the inside of the cut out.

SPECIFICATIONS

Light Source Semiconductor laser diode

Laser Wavelength 630 – 680nm Visible

Laser Power <5mw, CLASS IIIa LASER

PRODUCT

Rotation Speed approx. 600 rpm

Self-Leveling Range ± 5°

Indoor Visible Range 200' (61m) diameter

Range with Detector 1500' (450m) diameter

Level Accuracy ± 1/8" per 100'

(± 3mm per 31m)

Power Source 9.6V–18V DEWALT batteries

Operating Temperature 23°F to 122°F (-5°C to 50°C)

Storage Temperature -4°F to 158°F (-20°C to 70°C)

Water Resistant IPX4

Usage Indoor and Outdoor

Altitude Up to 6560' (2000m)

Maximum Relative 95%

Humidity

Rated Pollution Degree 2

English

2. Slide the battery pack in firmly until you hear the battery pack

lock in place.

REMOVING THE BATTERY PACK

1. Push the battery in slightly, press the release buttons, and firm-

ly pull the battery pack out of the receptacle.

2. The battery ejector pin (B) will aid in removing the pack.

3. To recharge the battery pack, insert it into the charger as

described in the charger section of this manual.

Control Panel

The laser is controlled by the ON/OFF button (C) and the manual

rotation button (D). Three indicator lights are on the control panel,

power LED light (E), X-axis leveling (F), and Y-axis leveling (G).

TURNING THE LASER ON

1. Insert the fully charged battery pack through the proper cut out

in battery adapter plate. Be sure that the battery is firmly

engaged.

2. Gently press the ON/OFF button (C) to power the laser on.

The laser diode will turn on and the power LED light (E) will

illuminate. The X-axis and Y-axis leveling lights (F, G) will

flash indicating that the laser is automatically leveling.

NOTE: The head will only rotate momentarily if the laser is leveling.

The head will begin or resume rotation once the laser is level.

TURNING THE LASER OFF

Gently press the ON/OFF button to turn the laser off. The power

LED Light will no longer be illuminated.

Using the Laser on a Tripod

1. Position the tripod securely and set it to the desired height.

2. Make sure that the top of the tripod is roughly level. the laser

will self-level only if the top of the tripod is within ± 5˚ of level.

If the laser is set up too far out of level, it will beep when it

reaches the limit of its leveling range. No damage will be done

to the laser, but it will not operate in an “out of level” condition.

3. Secure the laser to the tripod by screwing the threaded knob on

the tripod into the female thread on the bottom of the laser.

NOTE: Be sure that the tripod you are working with has a 5/8"–11

threaded screw to ensure secure mounting.

4. Turn the laser on by pressing the ON/OFF button (C). The

rotary head starts to spin after the unit levels itself.

Using the Laser in Level Mode

The laser can be positioned directly on the floor or on a tripod

(described above) for applications such as carpentry.

1. Place the laser on a smooth surface where it will not be

disturbed.

2. Position the laser for level setting as shown.

3. Turn the laser on by pressing the ON/OFF button (C).

4. The level indicator lights (F, G) blink on and off until the rotary

head is level.

5. The rotary head starts spinning after leveling and the indi-

cator lights remain on continuously.

NOTE: When the laser is out of leveling range. The rotary head

stops spinning, the laser turns off, the transmitter beeps and

the level indicator lights (F, G) blink.

English

Using the Laser in Manual Mode

To activate manual mode, press the manual button (D) for at least

two seconds. The laser will not self level and the level indicator

lights (F, G) do not light while in manual mode. Manual mode may

be used in either level or vertical orientation.

Using the Laser in Vertical Mode

The laser can be positioned to be used in the vertical orientation.

The laser will not self level in vertical mode.

1. Place the laser on a smooth surface where it will not be

disturbed.

2. Position the laser vertically as shown.

3. The laser must be put in manual mode when used in vertical

orientation.

4. Turn the laser on by pressing the ON/OFF button (C).

Using the Laser with a Wall Mount

The DW076 Rotary Laser has been designed to work with an

accessory Wall Mount (DW0770). It can be used for attaching the

tool to track or celing angle (mould) and to aid in acoustical ceiling

installation. Follow the directions below for using the wall mount.

CAUTION: Before attaching the laser level to wall track or

ceiling angle, be sure that the track or angle is properly secured.

1. Attach the Laser to the accessory wall mount.

LEVEL

MODE

VERTICAL

MODE

2. With the wall mount measuring scale (H) facing you, rotate the

wall mount clamp locking knob (I) towards you to open the

clamp jaws.

3. Position the clamp jaws around the wall track or ceiling angle

and as shown rotate the wall mount clamp locking knob away

from you to close the clamp jaws shut on the track. Be sure that

the wall mount clamp locking knob is securely locked before

proceding.

CAUTION: Always use a ceiling wire

hanger or equivalent material, in addition to

the wall mount clamp, to help secure the laser

level while mounting it to a wall. Thread the

wire through the handle of the laser level. DO

NOT thread the wire through the protective

metal cage. Additionally, screws may be used

to fasten the wall mount directly to the wall as

a back up. Screw holes (J) are located in the

wall mount next to the measuring scales.

4. The tool can be adjusted up and down to

the desired offset height for working. To

change the height, loosen the Rack ‘N

Pinion locking knob (K) located on the left

of the wall mount.

English

5. Turn the Rack ‘N Pinion adjustment knob (L) located to the right

of the wall mount to move the laser level up and down to set

your height. Use the wall mount measuring scale to pinpoint

your mark.

NOTE: It may be helpful to turn the power on and turn the rotary

head so that it puts a dot on one of the laser scales. The

EWALT target card is marked at 1-1/2" (38mm), therefore, it

may be easiest to set the offset of the laser to 1-1/2" (38mm)

below the wall angle.

6. Once you have positioned the

laser at the desired offset height,

tighten the Rack ‘N Pinion

locking knob to maintain the

offset.

7. Using the base leveling knob

(M), approximate a level position

from the wall.

Laser Accessories

Recommended accessories for use with your tool are available for

purchase at your factory-owned local service center.

CAUTION: The use of any non-recommended accessory may

be hazardous. Use only D

WALT accessories designed for use

with this product.

If you need any assistance in locating any accessory, please con-

tact D

EWALT Industrial Tool Co., 701 East Joppa Road, Baltimore,

MD 21286 or call 1-800-4-D

EWALT (1-800-433-9258). See our

catalog on the World Wide Web at www.dewalt.com.

Digital Laser Detector: DW0772

Some laser kits include a DEWALT digital laser detector. The

EWALT digital laser detector allows you to locate a laser beam

emitted by a rotary laser in bright light conditions or over long dis-

tances. The detector can be used in both indoor and outdoor situ-

ations where it is difficult to see the laser beam. The detector is not

for use with non-rotating lasers but is compatible with most rotary

red-beam or infra-red (invisible) beam lasers on the market. It can

be set to indicate the location of the beam to either the nearest 1/8"

or the nearest 1/25". The detector gives both visual signals through

the display window (N) and audio signals through the speaker (O)

to indicate the location of the laser beam.

The D

EWALT digital laser detector can be used with or without the

detector clamp. When used with the clamp, the detector can be

positioned on a grade rod, leveling pole, stud or post.

BATTERIES

The digital laser detector is powered by a 9 volt battery. To install

the battery provided, lift up on the battery compartment cover (P).

Place the 9 volt battery in the compartment, aligning the battery

as shown on the embossed icon (Q).

DETECTOR CONTROLS

The detector is controlled by the power/volume button (R) and the

accuracy mode button (S). When the power/volume button is

pushed once, the detector is turned on. The top of the display win-

English

dow shows the ON icon (T), and the volume icon (U). To decrease

the volume of the audible signal that the detector emits when it sens-

es a laser beam, push the button again; one of the half circles next

to the horn icon will dissappear. To turn off the audible signal push

the button a third time; the volume icon will dissapear. The D

EWALT

digital laser detector also has an auto shut-off feature. If a rotary

laser beam does not strike the beam detection window, or, if no but-

tons are pressed, the detector will shut itself off in about 30 minutes.

When the detector is on, the bottom of the window shows an accu-

racy mode icon. Either the ±1/25" accuracy mode icon (V) will

appear, or the ±1/8" accuracy mode icon (W) will appear. When

the ±1/25" accuracy mode icon appears, it indicates that the detec-

tor will give an “on grade” reading only when the laser beam is on

grade or no more than 1/25" above or below it. When the 1/8"

accuracy mode icon appears, it indicates that the detector will give

an “on grade” reading when the laser beam is on grade or approx-

imately 1/8" above or below it. Push the accuracy mode button (S)

once to change the accuracy mode.

Detector Operation

1. Set up and position the rotary laser that you will be using

according to the manufacturer’s directions. Turn the laser on

and make sure that the laser is rotating and emitting a laser

beam.

NOTE: This detector has been designed to be used only with a

rotating laser. The detector will not work with a stationary beam

laser level.

2. Turn the detector on by pressing the power/volume button (R).

3. Adjust the volume as desired as described in the Detector

Controls above.

4. Position the detector so that the detector window (X) is facing

the laser beam produced by the rotary laser. Move the detector

up or down within the approximate area of the beam, until you

have centered the detector. For information about the display

window indicators and the audible signal indicators, see the

table titled Indicators.

Slightly Slightly

Above Above On Below Below

Grade Grade Grade Grade Grade

fast fast steady slow slow

beep beep tone beep beep

audible

signals

INDICATORS

display icons

English

5. Use the marking notches (Y) to accurately mark the position of

the laser beam.

MOUNTING ON A GRADE ROD

1. To secure your detector to a grade rod, first attach the detector

to the clamp by pushing in on the clamp latch (Z). Slide the

tracks on the clamp (AA) around the rail on the detector (BB)

until the latch (CC) on the clamp pops into the latch hole (DD)

on the detector.

2. Open the jaws of the clamp by turning the clamp knob (EE)

counterclockwise.

3. Position the detector at the height needed and turn the clamp

knob clockwise to secure the clamp on the rod.

4. To make adjustments in height, slightly loosen the clamp,

reposition and retighten.

Detector Cleaning and Storage

• Dirt and grease may be removed from the exterior of the

detector using a cloth or soft, non-metallic brush.

• The DEWALT digital laser detector is waterproof. If you should

drop the detector in mud, wet concrete, or a similar substance,

simply hose the detector off. Do not use high pressure water,

(e.g., from a pressure washer).

• The best storage place is one that is cool and dry—away from

direct sunlight and excess heat or cold.

Detector Service

Except for batteries, there are no user serviceable parts in the

Digital Laser Detector. Do not disassemble the unit. Unauthorized

tampering with the laser detector will void all warranties.

Detector Troubleshooting

THE DETECTOR WILL NOT TURN ON

• Press and release the power/volume button.

• Check to see that the battery is in place and in the proper

position.

• If the detector is very cold, allow it to warm up in a heated area.

• Replace the 9 volt battery. Turn the unit on.

• If the detector still does not turn on, take the detector to a

EWALT service center.

THE DETECTOR’S SPEAKER MAKES NO SOUND

• Ensure that the detector is on.

• Press the power/volume button. It will toggle from high, to low,

to mute.

• Ensure that the rotary laser is spinning and that it is emitting a

laser beam.

• If the detector is still not making any sound, take it to a D

EWALT

service center.

THE DETECTOR IS NOT RESPONDING TO MY STATIONARY

LASER LEVEL

• The D

EWALT Digital Laser Detector has been designed to work

only with rotary lasers.

English

THE DETECTOR IS GIVING OFF A TONE BUT THE

LCD DISPLAY WINDOW IS NOT FUNCTIONING.

• If the detector is very cold, allow it to warm up in a heated area.

• If the LCD display window is still not functioning, take the detec-

tor to a D

EWALT service center.

LASER MAINTENANCE

1. Under some conditions, the

glass lens inside the rotary

head may collect some dirt or

debris. This will affect beam

quality and operating range.

The lens should be cleaned

with a cotton swab moistened

with water as shown.

2. The flexible rubber shield can be cleaned with a wet lint-free

cloth such as a cotton cloth. USE WATER ONLY — DO NOT

use cleansers or solvents. Allow the unit to air dry before

storing.

3. To maintain the accuracy of your work, check the calibration of

the laser often. See the Field Calibration Check section of this

manual.

4. Calibration checks and other maintenance repairs can be

performed by D

EWALT service centers. Two free calibration

checks are included under the D

EWALT One Year Free

Service Contract.

5. When the laser is not in use, store it in the kit box provided.

6. Do not store your laser in the kit box if the laser is wet. Dry

exterior parts with a soft, dry cloth and allow the laser to air dry.

7. Do not store your laser at temperatures below 0˚F (-18˚C) or

above 105˚F (41˚C).

CLEANING

Exterior plastic parts may be cleaned with a damp cloth and mild

detergent. Although these parts are highly solvent resistant,

NEVER use solvents. Never use compressed air to clean the laser.

Field Calibration Check

Field calibration checks should be done frequently. This section

provides instructions for performing simple field calibration checks

of your D

EWALT Rotary Laser. Field calibration checks do not

calibrate the laser. That is, these checks do not correct errors in the

leveling or plumbing capability of the laser. Instead, the checks

indicate whether or not the laser is providing a correct level and

plumb line. These checks cannot take the place of professional

calibration performed by a D

EWALT service center.

LEVEL MODE CALIBRATION CHECK

1. Set up a tripod 50' (15m) from a vertical wall as shown. Make

sure that the head of the tripod is level using a bubble vial.

APPROX. 50 ft.

(15m)

APPROX. 50 ft.

(15m)

BEAM

LASER UNIT

ROTATED 180˚

English

2. Mount the rotary laser on the tripod so that the X-axis points

away from the wall as shown.

3. Turn the laser on by pressing the ON/OFF button.

4. Mark the center of the beam elevation on the wall (a).

5. Turn the entire laser unit 180° so that the X-axis points towards

the wall and mark the center of the beam elevation (b).

6. If the distance between the two marks (a, b) is no more than

1/8" (3 mm), the laser is properly calibrated.

7. Repeat the above steps for the Y-axis by first pointing the Y-axis

away from the wall then turning the entire laser unit 180° again.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustments should be performed by a D

EWALT factory service

center, a D

EWALT authorized service center or other qualified

service personnel. Always use identical replacement parts.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty mate-

rials or workmanship for three years from the date of purchase.

This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others.

This warranty gives you specific legal rights and you may have

other rights which vary in certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

EWALT Power Tool, Laser, or Nailer for any reason, you can

return it within 90 days from the date of purchase with a receipt for

a full refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

RECONDITIONED PRODUCT: Reconditioned product is covered

under the 1 Year Free Service Warranty. The 90 Day Money Back

Guarantee and the Three Year Limited Warranty do not apply to

reconditioned product.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

EWALT for a free

replacement.

Français

SI VOUS AVEZ DES QUESTIONS OU VOULEZ NOUS FAIRE

PART DE VOS COMMENTAIRES CONCERNANT CET OUTIL OU

TOUT AUTRE OUTIL D

EWALT, COMPOSEZ SANS FRAIS LE :

1 800 433-9258

AVERTISSEMENT : Lire, comprendre et suivre

toutes les directives précisées ci-dessous, y com-

pris les consignes de sécurité, afin d’éviter les risques de

choc électrique, d’incendie ou de blessure grave.

CONSERVER CES DIRECTIVES

Consignes de sécurité concernant les

lasers

• Ne pas utiliser le laser dans une atmosphère explosive,

comme à proximité de liquides, de gaz ou de poussières

inflammables; le moteur peut créer des étincelles et enflammer

les vapeurs ou les poussières environnantes.

• N’utiliser le laser qu’avec les piles désignées, car l’utilisation

d’un autre type de piles pourrait entraîner un risque d’incendie.

• Lorsqu’on n’utilise pas le laser, le ranger hors de la portée

des enfants ou des personnes non qualifiées; les outils sont

dangereux entre les mains de personnes inexpérimentées.

• N’utiliser que les accessoires recommandés par le fabricant

pour le modèle concerné; un accessoire destiné à un laser par-

ticulier peut devenir dangereux lorsqu’il est utilisé avec un autre.

• L’outil doit être entretenu ou réparé par le personnel qual-

ifié seulement; toute maintenance effectuée par une person-

ne non qualifiée pourrait entraîner des risques de blessure.

Pour obtenir le numéro du centre de service D

WALT le plus

près, composer le 1 800 433-9258 ou consulter le site Internet

http://www.dewalt.com.

• Ne pas utiliser un dispositif optique, tel qu’un téléscope ou

une lunette de passage, pour examiner le faisceau laser afin

d’éviter de blesser grièvement les yeux.

• Ne pas mettre le laser dans une position qui pourrait

encourager une personne à regarder directement le fais-

ceau laser, volontairement ou involontairement, car cela pour-

rait blesser grièvement les yeux.

• Mettre le laser hors tension après chaque utilisation, car un

laser laissé sous tension encourage une personne à regarder

directement le faisceau laser.

• La réparation et l’entretien DOIVENT être effectués dans un

centre de service autorisé ou par du personnel qualifié;

toute opération d’entretien ou de réparation effectuée par une

personne non qualifiée pourrait entraîner des blessures graves.

• Ne pas démonter l’outil laser; ce dernier ne comprend aucune

pièce interne destinée à être entretenue par l’utilisateur.

• Ne pas utiliser le laser en présence d’un enfant, ni autoriser

les enfants à utiliser le laser afin d’éviter les blessures graves

aux yeux.

• Ne pas retirer ni abîmer les étiquettes d’avertissement; le

fait de retirer les étiquettes augmentera les risques d’exposition

aux rayonnements laser.

• S’assurer de bien déposer le laser sur une surface de

niveau afin de l’empêcher de tomber et de s’endommager ou

de blesser l’utilisateur.

• Porter des vêtements appropriés; ne pas porter de vête-

ments amples ni de bijoux. Couvrir ou attacher les cheveux

longs. Garder les cheveux, les vêtements, les bijoux et les

gants éloignés des pièces mobiles, car ceux-ci peuvent s’y

coincer. Se tenir éloigné des évents puisque ces derniers pour-

raient camoufler des pièces mobiles.

MISE EN GARDE : L’utilisation de procédures, de commandes

ou de réglages autres que ceux précisés aux présentes pourrait

entraîner des risques d’exposition aux rayonnements laser.

AVERTISSEMENT! NE PAS DÉMONTER LE LASER

ROTATIF. L’outil ne comprend aucune pièce interne destinée à

Français

être entretenue par l’utilisateur. Le fait de démonter le laser

rotatif annulera toute garantie appuyant ce produit; on ne doit

jamais modifier ce dernier de quelque manière que ce soit afin

d’éviter d’entraîner des risques d’exposition aux rayonnements.

• L’étiquette apposée sur l’outil peut afficher les symboles suivants :

V ........................volts

MW ....................milliwatts

................symbole d’avertissement du laser

nm......................longueur d’onde exprimée en nanomètres

IIIa......................laser de classe IIIa

• Pour des fins pratiques et de sécurité, la scie à onglets com-

prend les étiquettes d’avertissement suivantes

ÉVITER L’EXPOSITION AUX RAYONNEMENTS LASER

ÉMIS PAR CES OUVERTURES.

DANGER. RAYONNEMENTS LASER. ÉVITER LES

RISQUES D’EXPOSITION OCULAIRE.

Information sur les lasers

Le laser rotatif sans fil DW076 est répertorié en tant que PRODUIT

À LASER DE CLASSE IIIa; il est conforme aux exigences perti-

nentes contenues au chapitre 21 du Code of Federal Regulations

(ou CFR) des États-Unis établies par les organismes américains

suivants : le Department of Health, Education and Welfare, le Food

and Drug Administration et le Center for Devices and Radiological

Health.

Ces dispositifs sont conformes aux dispositions de la partie 15 des

règlements de la FCC. Le fonctionnement doit respecter les deux

conditions suivantes : (1) ce dispositif ne doit pas causer de brouil-

lage nuisible, et (2) ce dispositif doit accepter tout brouillage qu’il

reçoit, y compris celui qui cause un fonctionnement indésirable.

REMARQUE : Les essais ont démontré que cet appareil respecte

les limites régissant un dispositif numérique de classe B, confor-

mément aux dispositions de la partie 15 des règlements de la

FCC. Le but de ces limites est de fournir une protection

raisonnable contre le brouillage nuisible dans une installation

résidentielle. Cet appareil génère, utilise et peut produire une

énergie radiofréquence rayonnée et, lorsqu’il n’est pas installé et

utilisé conformément aux directives, peut causer le brouillage

nuisible des communications radio. Cependant, il n’existe aucune

garantie que le brouillage ne se produira pas dans une installa-

tion particulière. Si cet appareil entraîne le brouillage nuisible de

la réception radio ainsi que celle des programmes de télévision,

ce qui peut être déterminé en allumant et en éteignant l’appareil,

on invite l’utilisateur à tenter de corriger le problème relié au

brouillage au moyen de l’une des deux méthodes suivantes :

• en réorientant ou en déplaçant l’antenne de réception,

• en augmentant l’espace entre l’appareil et le récepteur ou

• en raccordant l’appareil à une prise murale reliée à un

circuit autre que celui dans lequel le récepteur est branché.

Français

• Communiquer avec le distributeur ou un technicien de

radio ou de téléviseur qualifié pour obtenir de l’aide.

Cet appareil numérique de la classe B est conforme à la norme

NMB-003 du Canada.

Consignes de sécurité importantes

concernant les bloc-piles

L’outil fonctionne sur un bloc-pile DEWALT de 9,6, de 12,0 de 14,4

ou de 18 volts. Au moment de commander un bloc-pile de

rechange, s’assurer d’inclure le numéro de catalogue et la tension

appropriée. Les bloc-piles à durée prolongée durent plus

longtemps que les bloc-piles standard. Consulter le diagramme à

la fin du présent manuel afin de vérifier la compatibilité du chargeur

avec le bloc-pile.

REMARQUE : Bien que l’outil puisse fonctionner au moyen de l’un

ou l’autre de ces bloc-piles, on doit s’assurer d’en choisir un de ten-

sion appropriée. Un bloc-pile perd graduellement sa charge s’il

n’est pas laissé dans le chargeur; il est donc recommandé de le

laisser dans le chargeur en tout temps.

Le bloc-pile n’est pas complètement chargé au moment de sa

livraison. Avant d’utiliser le bloc-pile et le chargeur, lire attentive-

ment toutes les consignes de sécurité énumérées ci-dessous et

suivre les méthodes de chargement précisées ci-dessous.

LIRE TOUTES LES DIRECTIVES

• NE PAS incinérer le bloc-pile même s’il est gravement

endommagé ou complètement usé, car il pourrait exploser en

présence de flammes.

• Les cellules peuvent subir une fuite légère par suite d’un

usage extrême ou d’une exposition à certaines tempéra-

tures; cela n’indique pas un problème. Cependant, si le scellant

externe est percé et le liquide entre en contact avec la peau, on

doit:

a. se laver rapidement la partie du corps touchée avec de l’eau

savonneuse;

b. neutraliser l’effet au moyen d’un acide doux tel que du jus de

citron ou du vinaigre;

c. si les yeux sont touchés, les rincer à fond avec de l’eau

propre pendant au moins 10 minutes et consulter

immédiatement un médecin. (REMARQUE AUX FINS

MÉDICALES : ce liquide contient une solution composée

de 25 à 35 % d’hydroxyde de potassium).

• Ne recharger les blocs-piles que dans des chargeurs D

WALT.

• NE PAS immerger le chargeur ou le bloc-pile dans l’eau ou tout

autre liquide quelconque, ni l’éclabousser.

• Ne pas ranger ou utiliser l’outil et le bloc-pile là où la tem-

pérature ambiante peut excéder 40 °C (105 °F) (comme des

hangars ou des bâtiments métalliques en été).

DANGER : Risques d’électrocution. Ne jamais tenter d’ouvrir le

bloc-pile pour quelque raison que ce soit. Si le compartiment se

rupture ou subit des dommages, ne pas l’insérer dans le chargeur

afin d’éviter les risques.de choc électrique ou d’électrocution. On

doit retourner les bloc-piles endommagés à un centre de service

afin qu’ils puissent être recyclés.

REMARQUE : Un capuchon est fourni avec la

pile en vue d’être utilisé chaque fois qu’on retire cette

dernière de l’outil ou du chargeur en vue de la ranger

ou de la transporter; enlever le capuchon avant de

remettre la pile dans le chargeur ou dans l’outil.

AVERTISSEMENT : Risques d’incendie. S’assurer, au

moment de ranger ou de transporter un bloc-pile ou une pile,

qu’aucun objet métallique n’entre en contact avec leurs

bornes à découvert de celui-ci. Par exemple, il faut éviter de

placer un bloc-pile ou une pile sans capuchon dans un tablier, une

poche, une boîte à outils ou un tiroir (etc.) contenant des objets tels

que des clous, des vis ou des clés, car tout contact entre les

bornes à découvert et un objet métallique comme une clé, une

pièce de monnaie, un outil à main. etc. pourrait causer un

incendie. En effet, les règlements américains Hazardous Material

Français

Regulations (HMR) du US Department of Transportation interdisent

le transport d’un bloc-pile ou d’une pile dans tout moyen de trans-

port commercial ou aéronef (que ce soit dans une valise ou le

bagage de cabine) SAUF s’ils sont bien protégés contre les courts-

circuits. On doit donc s’assurer, lorsqu’on transporte un bloc-pile ou

une pile séparément, de bien protéger et isoler les bornes contre

tout matériau qui risque d’entrer en contact avec eux et de causer

un court-circuit.

Sceau RBRC

Le sceau RBRC

de la Rechargeable Battery

Recycling Corporation apposé sur la pile au nickel-

cadmium (ou le bloc-pile) indique que les coûts de

recyclage de ce dernier à la fin de sa vie utile ont déjà

été payés par D

EWALT. En certains endroits, la mise

au rebut ou aux ordures municipales des piles au nickel-cadmium

est illégale; le programme de «RBRC» constitue donc une solution

des plus pratiques et écologiques.

La «RBRC», en collaboration avec D

EWALT et d’autres utilisateurs

de piles, a mis sur pied des programmes aux États-Unis dans le but

de faciliter la collecte des piles déchargées. D

EWALT encourage

ses utilisateurs à participer à son programme de protection de l’en-

vironnement et de conservation des ressources naturelles en

retournant les piles usagées à un centre de service D

EWALT ou

chez un dépositaire local afin qu’elles puissent être recyclées. On

peut en outre se renseigner auprès d’un centre de recyclage local

pour connaître d’autres sites les acceptant.

RBRC

est une marque déposée de la

Rechargeable Battery

Recycling Corporation.

Consignes de sécurité importantes

concernant les chargeurs de piles

CONSERVER CES DIRECTIVES : Le présent manuel comprend

d’importantes directives et consignes de sécurité concernant les

chargeurs de piles.

• Avant d’utiliser le chargeur, lire toute directive et étiquettes de

mise en garde apposées sur le chargeur, le bloc-pile et le pro-

duit utilisant le bloc-pile.

DANGER : Risques d’électrocution. Les bornes du chargeur

conduisent une tension de 120 volts. Ne pas toucher le chargeur ou

la borne avec des objets conducteurs, chocs électriques ou électro-

cution peuvent en résulter.

AVERTISSEMENT : Risques de choc électrique. Ne jamais laiss-

er de liquide s’infiltrer à l’intérieur du chargeur afin d éviter les

risques de choc électrique.

MISE EN GARDE : Risques de brûlure. Afin de réduire les

risques de blessure, ne charger que des piles rechargeables au

nickel-cadmium D

WALT. Car les autres peuvent éclater et entraîn-

er des blessures ou des dommages matériels.

MISE EN GARDE : Sous certaines conditions, lorsque le

chargeur est enfiché au bloc d’alimentation, les contacts de charge

exposés à l’intérieur du chargeur peuvent être court-circuités par

des corps étrangers. Les corps étrangers de nature conductrice

telle que, mais pas limité à, la paille de fer, les feuilles d’aluminium,

ou tout accumulation de particules métalliques doivent être tenus

éloignés des cavités du chargeur. Toujours débrancher le chargeur

du bloc d’alimentation lorsque le bloc-pile n’y est pas inséré ou

avant de le nettoyer.

• NE PAS tenter de charger le bloc-piles avec des chargeurs

autres que ceux décrits dans ce manuel. Le chargeur et le

bloc-pile sont conçus spécialement pour être utilisés ensemble.

• Ces chargeurs n’ont pas été conçus pour une utilisation

autre que recharger les piles rechargeables D

WALT. Toute

autre utilisation pose des risques d’incendie, de choc électrique

ou d’électrocution.

• Ne pas exposer le chargeur à la pluie ou à la neige.

• Débrancher le chargeur en saisissant la fiche, non le

cordon, afin de réduire les risques d’endommager la fiche ou le

cordon électrique.

La page charge ...

DeWalt Laser Level DW076 Manuel utilisateur

Marque: DeWalt

Modèle: Laser Level DW076

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt Laser Level DW076 User manual
español: DeWalt Laser Level DW076 Manual de usuario

Documents connexes

Autres documents

Johnson Level & Tool 40-6705 Manuel utilisateur