Hikoki CR 18DL Manuel utilisateur

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner

la mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être

conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual BEFORE operating the power tool. Please keep this

manual available for other users and owners before they use the power tool. This

manual should be stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de utilizar la herramienta

eléctrica. Este manual debe ser guardado en un lugar seguro.

Model Cordless Reciprocating Saw

Modèle Scie alternative à batterie

Modelo Sierra reciprocante a batería

CR 18DL

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

00Cover_CR18DL_US 8/6/12, 13:421

2

TABLE DES MATIERES

ÍNDICE

Français

Español

CONTENTS

English

Página

MONTAJE Y OPERACIÓN ...................................... 70

APLICACIONES ................................................... 70

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA ............................................ 70

MÉTODO DE CARGA .......................................... 70

ANTES DE LA UTILIZACIÓN .............................. 75

ANTES DE LA OPERACIÓN ................................ 76

COMO USAR LA SIERRA SABLE

A BATERÍA ................................................... 78

MANTENIMIENTO E INSPECCIÓN ........................ 82

ACCESORIOS ........................................................... 84

ACCESORIOS ESTÁNDAR ................................. 85

ACCESORIOS OPCIONALES .............................. 86

LISTA DE PIEZAS .................................................... 88

Página

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD

..... 59

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

... 59

SEGURIDAD ............................................................. 60

ADVERTENCIAS DE SEGURIDAD GENERAL

DE LA HERRAMIENTA ELÉCTRICA ............ 60

NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD

.... 63

INSTRUCCIONES IMPORTANTES PARA LA

UTILIZACIÓN DEL SIERRA SABLE

A BATTERÍA

................................................... 64

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

.................. 65

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS

... 66

ADVERTENCIA DE LA BATERÍA DE LITIO ......... 67

DESCRIPCIÓN FUNCIONAL .................................... 68

NOMENCLATURA ............................................... 68

ESPECIFICACIONES ............................................ 69

Page

IMPORTANT SAFETY INFORMATION .............. 3

MEANINGS OF SIGNAL WORDS ...................... 3

SAFETY .................................................................... 4

GENERAL POWER TOOL SAFETY WARNINGS ....

4

SPECIFIC SAFETY RULES AND SYMBOLS ....... 7

IMPORTANT SAFETY INSTRUCTIONS FOR USE

OF THE CORDLESS RECIPROCATING SAW

.... 8

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ............................. 9

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER .................................... 10

CAUTION ON LITHIUM-ION BATTERY ............. 11

FUNCTIONAL DESCRIPTION .................................. 12

NAME OF PARTS ................................................ 12

SPECIFICATIONS ................................................ 13

Page

ASSEMBLAGE ET FONCTIONNEMENT ................ 41

APPLICATIONS ................................................... 41

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 41

MÉTHODE DE RECHARGE ................................. 41

AVANT L’UTILISATION ...................................... 46

AVANT L’OPERATION ........................................ 47

COMMENT UTILISER LA SCIE

ALTERNATIVE À BATTERIE ........................ 49

ENTRETIEN ET INSPECTION .................................. 53

ACCESSOIRES ......................................................... 56

ACCESSOIRES STANDARD ............................... 56

ACCESSOIRES SUR OPTION ............................. 57

LISTA DES PIÈCES .................................................. 88

Page

ASSEMBLY AND OPERATION ............................... 14

APPLICATIONS ................................................... 14

REMOVAL AND INSTALLATION METHOD

OF BATTERY ................................................ 14

CHARGING METHOD ......................................... 14

BEFORE USE ....................................................... 19

PRIOR TO OPERATION ....................................... 19

HOW TO USE THE CORDLESS

RECIPROCATING SAW ................................ 22

MAINTENANCE AND INSPECTION ....................... 25

ACCESSORIES ......................................................... 27

STANDARD ACCESSORIES ............................... 27

OPTIONAL ACCESSORIES ................................. 29

PARTS LIST .............................................................. 88

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ

...... 30

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.... 30

SECURITE ................................................................ 31

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES...

31

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES

.... 34

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L'UTILISATION DU SCIE ALTERNATIVE À BATTERIE

.. 35

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE .......... 36

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR L’UTILISATION

DE LA BATTERIE ET DU CHARGEUR DE BATTERIE

........... 37

PRÉCAUTIONS RELATIVES A LA BATTERIE AU

LITHIUM ION ................................................ 38

DESCRIPTION FONCTIONNELLE ........................... 39

NOM DES PARTIES ............................................ 39

SPECIFICATIONS ................................................ 40

00Cover_CR18DL_US 7/28/09, 21:572

3

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

01Eng_CR18DL_US 7/28/09, 21:573

4

English

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING:

Read all safety warnings and instructions.

Failure to follow the warnings and instructions may result in electric shock, fire and/or

serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power

tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust of fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.c)

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool.

Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor

use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current

device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool.

Do not use a power tool while you are tired or under the influence of drugs, alcohol

or medication.

01Eng_CR18DL_US 7/28/09, 21:574

5

English

A moment of inattention while operating power tools may result in serious personal

injury.

b) Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench or a key left attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables better control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous and must be

repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool

accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the power tool’s operation.

If damaged, have the power tool repaired before use.

Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these

instructions, taking into account the working conditions and the work to be

performed.

Use of the power tool for operations different from those intended could result in a

hazardous situation.

01Eng_CR18DL_US 7/28/09, 21:575

6

English

5) Battery tool use and care

a) Recharge only with the charger specified by the manufacturer.

A charger that is suitable for one type of battery pack may create a risk of fire when

used with another battery pack.

b) Use power tools only with specifically designated battery packs.

Use of any other battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like paper

clips, coins, keys, nails, screws, or other small metal objects, that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally

seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known [to the State of California] to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

01Eng_CR18DL_US 7/28/09, 21:576

7

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tool by insulated gripping surfaces, when performing an operation where

the cutting accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make exposed metal parts of the power

tool “live” and could give the operator an electric shock.

2. Use clamps or another practical way to secure and support the workpiece to a stable

platform.

Holding the work by hand or against your body leaves it unstable and may lead to loss

of control.

3. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s moving parts.

4. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

5. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

6. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction

Manual.

7. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with

its operation or unauthorized personnel.

8. Definitions for symbols used on this tool.

V ............. volts

—

---

............ direct current

Hz ........... hertz

A ............. amperes

no .......... no load speed

---/min .... revolutions or reciprocation per minute

9. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

10. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

11. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

12. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

01Eng_CR18DL_US 7/28/09, 21:577

8

English

13. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

14. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE CORDLESS

RECIPROCATING SAW

WARNING: Death or serious bodily injury could result from improper or unsafe

use of the Cordless Reciprocating Saw. To avoid these risks, follow

these basic safety instructions:

1. NEVER touch the tool blade with bare hands after operation.

2. ALWAYS wear ear protectors when using for extended periods.

3. ALWAYS wear eye protection that meets the requirement of the latest revision of

ANSI Standard Z87.1.

4. ALWAYS be careful with buried object such as an underground, wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric

shock.

Comfirm if there are any buried object such as electric cable within the wall, floor or

ceiling where you are going to operate here after.

01Eng_CR18DL_US 7/28/09, 21:578

9

English

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER

WARNING: Death or serious bodily injury could result from improper or unsafe

use of battery chargers. To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating instructions for battery charger

Model UC18YRL, UC18YFL and UC18YGL2.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB7, EB9, EB12,

EB14, EB18, BCL14, BCL18 and EBM18 series. Other type of batteries may burst causing

personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturer

may result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same number, size, and shape as those of

plug on battery charger:

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating–for example:

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

02 1818 18 16

23 1818 16 14

34 1818 16 14

1,250 watts

125 volts

= 10 amperes

01Eng_CR18DL_US 7/28/09, 21:579

10

English

9. Do not operate battery charger with damaged cord or plug-replace them immediately.

10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

13. This battery charger might be attached to HITACHI battery operated tools as a standard

accessory. In this case, please confirm instruction Manual of the HITACHI battery

operated tools before using the battery charger.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY

AND BATTERY CHARGER

You must charge the battery before you can use the power tool. Before using the model

UC18YRL or UC18YFL or UC18YGL2 battery charger, be sure to read all instructions and

cautionary statements on it, the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPES EB7 SERIES, EB9 SERIES, EB12 SERIES,

EB14 SERIES, EB18 SERIES, BCL14 SERIES, BCL18 SERIES AND EBM18 SERIES. OTHER

TYPES OF BATTERIES MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING: Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in

use.

01Eng_CR18DL_US 7/28/09, 21:5710

11

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop

the output.

In the cases of 1 to 3 described below, when using this product, even if you are pulling the

switch, the motor may stop. This is not the trouble but the result of protection function.

1. When the battery power remaining runs out (the battery voltage drops to about 12V),

the motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and

eliminate causes of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the battery power may stop.

In this case, stop using the battery and let the battery cool. After that, you can use it

again.

01Eng_CR18DL_US 7/28/09, 21:5711

12

English

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool.

NAME OF PARTS

1. Cordless Reciprocating Saw (CR18DL)

䡬 Battery

Fig. 1

Switch trigger

Handle

Blade holder

Base

Blade

Lever

Rubber cap

Housing

Front cover

Brush cap

Lock-off button

Battery

Nameplate

Terminal hole

Latch

Terminal hole

Latch

Nameplate

01Eng_CR18DL_US 7/28/09, 21:5712

13

English

2. Battery Charger

SPECIFICATIONS

1. Cordless Reciprocating Saw (CR18DL)

Motor DC motor

No-Load Speed 0 – 2100/min.

Stroke 1-1/8" (28 mm)

Capacity Mild Steel Pipe: O.D. 3-1/2" (90 mm)

Vinyl Chloride Pipe: O.D. 3-1/2" (90 mm)

Wood: Depth 3-1/2" (90 mm)

Model EBM1830 BCL1815

Battery Type Lithium – ion battery

Voltage DC 18V

Weight 7.5 lbs. (3.4 kg) 7.0 lbs. (3.2 kg)

NOTE: The charging time may vary according to ambient temperature and power source

voltage.

2. Battery Charger

Model UC18YRL / UC18YFL UC18YGL2

Input power source Single phase: AC120V 60Hz

Charging time

Approx. 20 min. .....BCL1815 Approx. 40 min. .....BCL1815

(At a temperature of 68°F (20°C))

Approx. 45 min. .....EBM1830 Approx. 90 min. .....EBM1830

Charging voltage DC 7.2 – 18V

Charging current DC 3.5A DC 2.0A

Weight 1.3 lbs. (0.6 kg) 0.9 lbs. (0.4 kg)

Overheat lamp (green)

Nameplate

Caution

plate

Body

Fig. 2

Battery

installation hole

Charge status lamp (red)

Pilot lamp

Nameplate

Body

Fig. 3

Battery

installation hole

01Eng_CR18DL_US 7/28/09, 21:5713

14

English

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Cutting metal and stainless steel pipe.

䡬 Cutting various lumber.

䡬 Cutting mild steel, aluminum and copper plate.

䡬 Cutting synthetic resins, such as phenol resin and vinyl chloride.

REMOVAL AND INSTALLATION METHOD OF BATTERY

CAUTION: Be sure to keep the switch turned off and the lock-off button moved to

right position (lock position). (See Fig. 23)

䡬 How to install the battery.

Align the battery with the groove in tool

handle and slip it into place.

Always insert it all the way until it locks in

place with a little click. If not, it may acci-

dentally fall out of the tool, causing injury

to you or someone around you. (Fig. 4)

䡬 How to remove the battery.

Withdraw battery from the tool handle while

pressing the latches (2 pcs.) on the sides of

the battery. (Fig. 4)

CHARGING METHOD

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING: Do not charge at voltage higher than indicated on the

nameplate.

If charged at voltage higher than indicated on the nameplate,

the charger will burn out.

Fig. 4

Handle

Latch

Push

Battery

Pull out

Insert

Switch trigger

01Eng_CR18DL_US 7/28/09, 21:5714

15

English

Battery

Charge status lamp (red)

Overheat lamp (green)

<UC18YRL, UC18YFL>

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted into the receptacle, the charge

status lamp will blink in red. (At 1-second intervals)

WARNING:

Do not use the electrical cord if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 5. Make sure it contacts the

bottom of the battery charger.

Fig. 5

3. Charging

䡬 When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 2)

NOTE: If the pilot lamp flikers in red, pull out the plug from the receptacle and check if

the battery is properly mounted.

䡬 When the battery is fully charged, the pilot lamp will bilink in red slowly. (At 1-second

intervals) (See Table 2)

01Eng_CR18DL_US 7/28/09, 21:5715

16

English

䡬 Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted into the receptacle, pilot lamp will

blink in red. (At 1-second intervals)

Table 3

Rechargeable batteries Temperatures at which the battery can be recharged

EBM1830, BCL1815 32°F — 122°F (0°C — 50°C)

Before

charging

While

charging

Charging

complete

Charging

impossible

Overheat

standby

Malfunction in the

battery or the charger

Battery overheated.

Unable to charge

(Charging will commence

when battery cools).

Table 2

Indications of the pilot lamp

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light

for 0.1 seconds. (off for 0.1 seconds)

Lights continuously

Charge

status

lamp

(RED)

Overheat

lamp

(GREEN)

NOTE: When standby for cooling battery, UC18YRL cools the overheated battery by cooling

fan.

01Eng_CR18DL_US 7/28/09, 21:5716

17

English

WARNING:Do not use the electrical cord if damaged. Have it

repaired immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in Fig. 6. Make sure it contacts the

bottom of the battery charger.

3. Charging

䡬 When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 4)

NOTE: If the pilot lamp does not light or blink in red, pull out the plug from the receptacle

and check if the battery is properly mounted.

䡬 When the battery is fully charged, the pilot lamp will blink in red slowly. (At 1-second

intervals) (See Table 4)

Fig. 6

Pilot lamp

01Eng_CR18DL_US 7/28/09, 21:5717

18

English

䡬 Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as shown in Table 3, and batteries that

have become hot should be cooled for a while before being recharged.

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the battery from the battery charger.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal

time required for recharging will be restored by recharging the batteries 2 – 3 times.

CAUTION:

䢇 When the battery charger has been continuously used, the battery charger will be

heated, thus constituting the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

䢇 If the battery is charged while it is heated because it has been left for a long time in a

location subject to direct sunlight or because the battery has just been used, the pilot

lamp of the charger lights for 1 second, does not light for 0.5 seconds (off for 0.5

seconds).

The battery will not be recharged. In such a case, let the battery cool before charging.

Before

charging

While

charging

Charging

complete

Overheat

standby

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Table 4

Indications of the pilot lamp

Blinks

Lights

Blinks

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (off for 0.5 seconds)

Lights for 1 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Pilot lamp

(red)

01Eng_CR18DL_US 7/28/09, 21:5718

19

English

How to make the batteries perform longer.

䡬 Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

䡬 Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will heated,

thus constituting the cause of the failures. Once the charging has been completed,

give 15 minutes rest until the next charging.

● If the battery is rechraged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may light in green. (UC18YRL, UC18YFL)

The battery will not be recharged. In such a case, let the battery cool before charging.

● When the pilot lamp flickers in red (at 0.2 second intervals), check for and take out any

foreign objects in the charger’s battery installation hole. If there are no foreign objects,

it is probable that the battery or charger is malfunctioning. Take it to your authorized

Service Center. (UC18YRL, UC18YFL)

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

PRIOR TO OPERATION

1. Mounting the blade

This unit employs a detachable mechanism that

enables mounting and removal of saw blades

without the use of a wrench or other tools.

(1) Turn on and off the switching trigger several

times so that the lever can jump out of the front

cover completely. Thereafter, turn off the switch

and remove the battery. (Fig. 7)

CAUTION: Be absolutely sure to keep the switch

turned off and the battery removed

to prevent any accident.

Lever

Front cover

Fig. 7

01Eng_CR18DL_US 7/28/09, 21:5819

20

English

Fig. 8

Lever

Fig. 9

Blade

Slit of plunger

(2) Push the lever in the direction of the arrow mark

shown in Fig. 8 marked on the lever.

(3) Insert the saw blade all the way into the small

slit of the plunger tip with the lever pushing.

You can mount this blade either in the upward

or downward direction. (Fig. 9, Fig. 10)

(4) When you release the lever, the spring force will

return the lever to the correct position

automatically. (Fig. 11)

(5) Pull the back of the saw blade two or three times

by hand and check that the blade is securely

mounted. When pulling the blade, you will know

it is properly mounted if it clicks and the lever

moves slightly. (Fig. 12)

CAUTION: When pulling the saw blade, be

absolutely sure to pull it from the

back. Pulling other parts of the blade

will result in an injury.

2. Dismounting the blade

(1) Turn on and off the switching trigger several

times so that the lever can jump out of the front

cover completely. Thereafter, turn off the switch

and remove the battery. (Fig. 7)

CAUTION: Be absolutely sure to keep the switch

turned off and the battery removed

to prevent any accident.

(2) After you have pushed the lever in the direction

of the arrow mark shown in Fig. 8, turn the blade

so it faces downward. The blade should fall out

by itself. If the blade doesn’t fall out, pull it out

by hand.

CAUTION: Never touch the saw blade immediately

after use. The metal is hot and can easily

burn your skin.

WHEN THE BLADE IS BROKEN

Even when the saw blade is broken and remains

inside the small slit of the plunger, it should fall out

if you push the lever in the direction of the arrow

mark, and face the blade downward. If it doesn’t fall

out itself, take it out using the procedures explained

below.

Blade

Slit of plunger

Fig. 10

Fig. 11

Lever

Fig. 12

Lever

Blade

01Eng_CR18DL_US 7/28/09, 21:5820

La page charge ...

Hikoki CR 18DL Manuel utilisateur

Ce manuel convient également à

Hikoki CR 18DL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents