Losi LOS03028T2 Le manuel du propriétaire

Marque: Losi

Modèle: LOS03028T2

Catégorie: Jouets télécommandés

Taper: Le manuel du propriétaire

Ce manuel convient également à

Before operating this vehicle, please read all printed materials thoroughly.

Horizon Hobby is not responsible for inadvertent errors in this manual.

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D’UTILISATION

MANUALE DI ISTRUZIONI

LASERNUT TENACITY ULTRA 4 ROCK RACER

1/10

Scale 4WD RTR

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

Age Recommendation: Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to

the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and

responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with

incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance.

It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product.

Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with

DSM or Spektrum technology.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby,LLC. For up-to-date product literature, visit www.horizonhobby.com

or www.towerhobbies.com and click on the support or resources tab for this product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superﬁcial injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

As the user of this product, you are solely responsible for operating in a manner that does not

endanger yourself and others or result in damage to the product or property of others.

This model is controlled by a radio signal subject to interference from many sources outside

your control. This interference can cause momentary loss of control, so it is advisable to

always keep a safe distance in all directions around your model as this margin will help avoid

collisions or injury.

• Never operate your model with low transmitter batteries.

• Always operate your model in open spaces away from full-size vehicles, traffic and people.

• Never operate the model in the street or in populated areas for any reason.

• Carefully follow the directions and warnings for this and any optional support equipment

(chargers, rechargeable battery packs, etc.) you use.

• Keep all chemicals, small parts and anything electrical out of the reach of children.

• Never lick or place any portion of the model in your mouth as it could cause serious injury

or even death.

• Exercise caution when using tools and sharp instruments.

• Take care during maintenance as some parts may have sharp edges.

• Immediately after using your model, do NOT touch equipment such as the motor, electronic

speed control and battery, because they generate high temperatures. You may burn yourself

seriously touching them.

• Do not put ﬁngers or any objects inside rotating and moving parts, as this may cause

damage or serious injury.

• Always turn on your transmitter before you turn on the receiver in the car. Always turn off the

receiver before turning your transmitter off.

• Keep the wheels of the model off the ground when checking the operation of the radio

equipment.

SAFETY PRECAUTIONS AND WARNINGS

TABLE OF CONTENTS

BOX CONTENTS ........................................................................................................3

COMPONENTS ..................................................................................................................3

SPEKTRUM SMART TECHNOLOGY .....................................................................................3

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS ..............................3

GENERAL PRECAUTIONS ................................................................................................... 3

WET CONDITIONS MAINTENANCE ....................................................................................3

QUICK START ............................................................................................................3

CHARGING THE BATTERY .........................................................................................3

INSTALLING THE BATTERY ........................................................................................ 4

TRANSMITTER FUNCTIONS ......................................................................................4

TRANSMITTER BATTERY INSTALLATION .............................................................................4

SR6100AT AVC TECHNOLOGY TELEMETRY RECEIVER AUX CHANNELS ...............................5

BINDING AND CALIBRATING THE RECEIVER ............................................................5

DISABLING AVC

TECHNOLOGY STABILITY ASSIST.............................................................5

FAILSAFE ..........................................................................................................................5

DRIVING PRECAUTIONS ..........................................................................................5

POWERING ON THE VEHICLE .................................................................................... 5

BEFORE RUNNING THE VEHICLE ............................................................................... 5

AVC

SENSITIVITY .................................................................................................... 5

RUN TIME ................................................................................................................. 6

TO IMPROVE RUN TIMES ...................................................................................................6

PERFORMING A CONTROL DIRECTION TEST.............................................................6

CHANGING THE TRAVEL ADJUST SETTINGS .............................................................6

SPEKTRUM

™

FIRMA

™

SMART 130A BRUSHLESS ESC (SPMXSE1130) .......................6

SPECIFICATIONS ...............................................................................................................6

ESC LED STATUS ...............................................................................................................6

AUDIBLE WARNING TONES ...............................................................................................6

ESC CALIBRATION PROCEDURE ........................................................................................6

ESC FUNCTIONS AND MODES ...........................................................................................7

PROGRAMMING TABLE ..................................................................................................... 7

ESC PROGRAMMING PROCEDURE ....................................................................................7

DESCRIPTIONS ..................................................................................................................7

SPEKTRUM™ FIRMA™ 1900KV BRUSHLESS MOTOR ..............................................8

PRECAUTIONS ..................................................................................................................8

GEARING ......................................................................................................................... 8

CHANGING THE PINION GEAR/GEAR RATIO ......................................................................8

SETTING THE GEAR MESH .................................................................................................8

TELEMETRY SETTINGS ....................................................................................................... 8

TROUBLESHOOTING GUIDE ......................................................................................8

LIMITED WARRANTY ............................................................................................... 8

WARRANTY AND SERVICE CONTACT INFORMATION ................................................9

FCC INFORMATION ..................................................................................................9

IC INFORMATION .....................................................................................................9

COMPLIANCE INFORMATION FOR THE EUROPEAN UNION ......................................9

REPLACEMENT PARTS ......................................................................................34–35

RECOMMENDED PARTS..........................................................................................36

OPTIONAL PARTS ...................................................................................................36

EXPLODED VIEW ..............................................................................................37–41

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

BOX CONTENTS

Your new Horizon Hobby vehicle has been designed and built with a combination of

waterproof and water-resistant components to allow you to operate the product in many

“wet conditions,” including puddles, creeks, wet grass, snow and even rain.

While the entire vehicle is highly water-resistant, it is not completely waterproof and your vehicle

should NOT be treated like a submarine. The various electronic components used in the vehicle,

such as the Electronic Speed Control (ESC), servo(s) and receiver are waterproof, however, most

of the mechanical components are water-resistant and should not be submerged.

Metal parts, including the bearings, hinge pins, screws and nuts, as well as the contacts in the

electrical cables, will be susceptible to corrosion if additional maintenance is not performed

after running in wet conditions. To maximize the long-term performance of your vehicle and

to keep the warranty intact, the procedures described in the “Wet Conditions Maintenance”

section below must be performed regularly if you choose to run in wet conditions. If you are

not willing to perform the additional care and maintenance required, then you should not

operate the vehicle in those conditions.

CAUTION: Failure to exercise caution while using this product and complying with the

following precautions could result in product malfunction and/or void the warranty.

GENERAL PRECAUTIONS

• Read through the wet conditions maintenance procedures and make sure that you have all

the tools you will need to properly maintain your vehicle.

• Not all batteries can be used in wet conditions. Consult the battery manufacturer before

use. Caution should be taken when using Li-Po batteries in wet conditions.

• Most transmitters are not water-resistant. Consult your transmitter’s manual or the

manufacturer before operation.

• Never operate your transmitter or vehicle where lightning may be present.

• Do not operate your vehicle where it could come in contact with salt water (ocean water or

water on salt-covered roads), contaminated or polluted water. Salt water is very conductive

and highly corrosive, so use caution.

• Even minimal water contact can reduce the life of your motor if it has not been certiﬁed as

water-resistant or waterproof. If the motor becomes excessively wet, apply very light throttle

until the water is mostly removed from the motor. Running a wet motor at high speeds may

rapidly damage the motor.

• Driving in wet conditions can reduce the life of the motor. The additional resistance of

operating in water causes excess strain. Alter the gear ratio by using a smaller pinion or larger

spur gear. This will increase torque (and motor life) when running in mud, deeper puddles, or

any wet conditions that will increase the load on the motor for an extended period of time.

WET CONDITIONS MAINTENANCE

• Drain any water that has collected in the tires by spinning them at high speed. With the

body removed, place the vehicle upside down and pull full throttle for a few short bursts

until the water has been removed.

CAUTION: Always keep hands, ﬁngers, tools and any loose or hanging objects

away from rotating parts when performing the above drying technique.

• Remove the battery pack(s) and dry the contacts. If you have an air compressor or a can of

compressed air, blow out any water that may be inside the recessed connector housing.

• Remove the tires/wheels from the vehicle and gently rinse the mud and dirt off with a

garden hose. Avoid rinsing the bearings and transmission.

NOTICE: Never use a pressure washer to clean your vehicle.

• Use an air compressor or a can of compressed air to dry the vehicle and help remove any

water that may have gotten into small crevices or corners.

• Spray the bearings, drive train, fasteners and other metal parts with a water-displacing light

oil. Do not spray the motor.

• Let the vehicle air dry before you store it. Water (and oil) may continue to drip for a few hours.

• Increase the frequency of disassembly, inspection and lubrication of the following:

- Front and rear axle hub assembly bearings.

- All transmission cases, gears and differentials.

- Motor—clean with an aerosol motor cleaner and re-oil the bushings with lightweight

motor oil.

WATER-RESISTANT VEHICLE WITH WATERPROOF ELECTRONICS

QUICK START

Please read the entire manual to gain a full understanding of the LASERNUT U4 RTR vehicle, ﬁne-tuning the setup and performing maintenance.

1. Read the safety precautions found in this manual.

2. Charge a battery for the vehicle. Refer to the included charging warnings and

instructions for battery charging information.

3. Install the AA batteries in the transmitter. Only use alkaline

or rechargeable batteries.

4. Install the fully charged battery in the vehicle.

5. Power ON the transmitter and then the vehicle. Wait 5 seconds for the ESC

to initialize. Always power the transmitter ON before the vehicle and power

it OFF after the vehicle has been powered OFF.

6. Check the steering and throttle control directions. Verify that the servos are

moving in the correct direction.

7. Drive your vehicle.

8. Perform any necessary maintenance.

CHARGING THE BATTERY

The Lasernut Ultra 4 includes Spektrum SMART Technology in the ESC and receiver, which can

provide you with telemetry information including battery voltage and vehicle temperature.

To take advantage of SMART Technology, you’ll need a SMART compatible transmitter. The

included DX3 Active transmitter can be upgraded with the Spektrum Bluetooth Module

(SPM6741) Or, consider upgrading to a SMART Technology compatible Spektrum transmitter

like the DX5C (SPMR5100–transmitter only), DX5 Pro (SPMR5010–transmitter only), or DX5

Rugged (SPM5200–includes SR515 receiver). Use Spektrum SMART batteries to power your

vehicle to take full advantage of SMART Technology, which can communicate battery data

through the SMART system as well.

Visit www.SpektrumRC.com for more information.

SPEKTRUM SMART TECHNOLOGY

COMPONENTS

• Losi

Tenacity

Lasernut Ultra 4 1/10-Scale 4WD RTR Rock Racer

• Spektrum

™

DX3

™

SMART Transmitter (SPMR2340)

• Spektrum SR6100AT 6 Channel AVC Telemetry Surface Receiver (SPMSR6100AT)

• Spektrum

15KG 23T Waterproof Metal Center Case Servo (SPMS614)

• Spektrum Firma

™

SMART 130A Brushless ESC (SPMXSE1130)

• 3668 - 1900Kv BL 4 Pole Motor (SPMXSM2200)

• 4 AA batteries (for transmitter)

Choose a battery designed to work with the Spektrum

™

Firma

™

SMART 130A Brushless ESC

(SPMXSE1130). We recommend the Spektrum 5000mAh 3S 11.1V 50C SMART LiPo hardcase

battery with IC5

connector (SPMX50003S50H5) or Spektrum 5000mAh 4S 14.8V 50C SMART

LiPo IC5 hardcase battery with IC5 connector (SPMC50004S50H5). Choose a charger designed

to charge 3S and/or 4S Li-Po batteries.

We recommend the Spektrum SMART dual-output AC charger, 2x100W (SPMXC1010).

Refer to your battery and charger manuals for usage, safety, and charging information.

IMPORTANT: When using a 3S battery, you must change the motor pinion gear to the 14T

pinion provided with your vehicle.

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

INSTALLING THE BATTERY

TRANSMITTER FUNCTIONS

A/B.

Channel 3 Button

Throttle/Brake

Steering Wheel

Steering Rate

Adjusts the end point of the steering

Brake Rate

Adjusts the braking end point.

Steering Trim

Adjusts the steering center point. Normally, the steering trim is adjusted until the vehicle tracks straight.

Throttle Trim

Adjusts the throttle neutral point

SMART Battery Level Indicator

Servo Reversing

To reverse the Throttle (TH) or Steering (ST) channel, switch the position of the correlating switch—

“N” is for normal, “R” is for reverse.

Throttle Limit

Limits throttle output to 50/75/100%

Select 50% or 75% for less experienced drivers or when you are driving the vehicle in a small area.

Power LED

• Solid red lights: Indicates radio connectivity and adequate battery power

• Flashing red lights: Indicates the battery voltage is critically low. Replace batteries

Power Button

Bind Button

This transmitter requires 4 AA batteries

1. Remove the battery cover from the transmitter.

2. Install the batteries as shown.

3. Install the battery cover.

CAUTION: Never remove the transmitter batteries while the

model is powered ON. Loss of model control, damage, or injury may

occur.

CAUTION: If using rechargeable batteries, charge only

rechargeable batteries. Charging non-rechargeable batteries may

cause the batteries to burst, resulting in injury to persons and/or damage

to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to national regulations.

TRANSMITTER BATTERY INSTALLATION

A/B

1. Ensure the ESC is powered OFF.

2. Remove the body clips and rotate the body up.

3. Undo the hook and loop straps.

4. Insert the battery into the battery tray.

5. Secure the hook and loop straps.

6. Connect the battery power lead to the ESC, noting proper polarity.

7. Power ON the transmitter, then the vehicle.

8. Rotate the body into place, and insert the body clips.

IMPORTANT: Secure the ESC wires so they do not interfere with the gearing.

NOTICE: If you are using a 3S Li-Po battery, use the included 14T pinion

gear. If you are using a 4S Li-Po battery, use the installed 12T pinion gear.

Using a 14T pinion gear with a 4S Li-Po battery will result in damage to

the ESC and motor.

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

DRIVING PRECAUTIONS

• Maintain sight of the vehicle at all times.

• Routinely inspect the vehicle for loose wheel hardware.

• Routinely inspect the steering assembly for any loose hardware. Driving the vehicle off-road

can cause fasteners to loosen over time.

• Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.

• Stop driving the vehicle when you notice a lack of power. Driving the vehicle when the

battery is discharged can cause the receiver to power off. If the receiver loses power, you

will lose control of the vehicle. Damage due to an over-discharged Li-Po battery is not

covered under warranty.

CAUTION: Do not discharge a Li-Po battery below 3V per cell. Batteries discharged

to a voltage lower than the lowest approved voltage may become damaged,

resulting in loss of performance and potential ﬁre when batteries are charged.

• Do not apply forward or reverse throttle if the vehicle is stuck.

Applying throttle in this instance can damage the motor or ESC.

• After driving the vehicle, allow the electronics to cool before driving the vehicle again.

IMPORTANT: Keep wires away from all moving parts.

POWERING ON THE VEHICLE

1. Center the ST TRIM and TH TRIM dials on the transmitter.

2. Power on the transmitter.

3. Install a fully charged battery pack per the

Installing the Battery

section.

4. Power on the ESC.

IMPORTANT: The vehicle MUST remain on a ﬂat, level surface and motionless

for at least 5 seconds.

BEFORE RUNNING THE VEHICLE

1. Check for free suspension movement. All suspension arms and steering components should

move freely. Any binds will cause the vehicle to handle poorly.

TIP: To increase the ride height and ground clearance of your vehicle, screw down the

shock collars to compress the springs.

2. Charge a battery pack. Always charge the battery pack as per the battery and/or charger

manufacturers’ instructions.

3. Set the transmitter steering trim. Follow the instructions to set the steering trim/subtrim so

that the vehicle drives straight with no input to the steering.

4. Perform a Control Direction Test.

AVC

SENSITIVITY

The ST RATE dial adjusts the sensitivity, or stability, value in the receiver. If you increase the

sensitivity, the AVC

system becomes more sensitive to the vehicle drifting left or right. You

would use maximum sensitivity during high speed driving or drag racing, when you want the

vehicle to stay in a straight line.

Turn the ST RATE knob counter-clockwise to reduce the sensitivity.

Turn the ST RATE knob clockwise to increase the sensitivity.

IMPORTANT: The ST RATE knob will only adjust the sensitivity when the

transmitter is bound to a DSMR

receiver. When the transmitter is bound

to a DSM

, DSM2

or DSM Marine receiver, the ST RATE knob controls

the steering dual rate.

BINDING AND CALIBRATING THE RECEIVER

Binding is the process of linking the SR6100AT receiver to your Spektrum transmitter. The AVC

features on the receiver can be enabled or disabled during the binding process.

IMPORTANT: You must calibrate the SR6100AT receiver each time it is placed in bind mode,

regardless of AVC being enabled or disabled.

Upon initial setup after the ﬁrst bind, the model must be conﬁgured for servo direction, trim

and travel. Then the receiver must be rebound and calibrated to those settings for proper

operation. Center the steering trim and throttle trim on the transmitter before beginning.

1. Press and hold the bind button on the receiver.

2. Power on the receiver. The orange LED ﬂashes, indicating the receiver is in bind mode.

Release the bind button after the orange LED illuminates.

3. Put your transmitter in bind mode. The bind process is complete when the orange LED

on the receiver remains lit. The receiver is now bound to the transmitter but must be

calibrated before it will operate.

4. Pull the transmitter trigger to full throttle, pause, then return the trigger to center.

5. Push the transmitter trigger to full brake, pause, then return the trigger to center.

6. Turn the transmitter steering wheel to full right, pause, then return the wheel to center.

7. Turn the transmitter steering wheel to full left, pause, then return the steering wheel to

center. The orange LED ﬂashes to conﬁrm the settings have been accepted.

8. Turn off the vehicle to complete the binding and calibration process.

CAUTION: When the bind process is complete, the throttle and steering channels

are active. Keep hands and loose objects away from all spinning parts on the

vehicle.

IMPORTANT: You must rebind the transmitter and receiver if you:

• Change the servo reversing after binding

• Change the travel after binding

• Change the receiver mounting orientation

DISABLING AVC

TECHNOLOGY STABILITY ASSIST

If you participate in organized racing, you may be required to turn AVC technology off.

To turn off AVC technology:

1. Connect power to the receiver and quickly press and release the bind button three times

(within 1.5 seconds).

2. Press and hold the bind button and to put the receiver in bind mode. release the buton

when the LED starts to ﬂash rapidly, indicating it is in bind mode.

When the AVC system has been disabled, the LED on the receiver will show three ﬂashes

upon power up, and then remain lit. The receiver is bound and operating normally when the

LED remains illuminated.

TIP: If the AVC feature in the receiver is active and the AVC menu in the transmitter is

Inhibited, AVC functions will default to the AUX 1 and AUX 2 operation, and in this scenario,

AVC will not work correctly.

FAILSAFE

In the unlikely event that the radio link is lost during use, the receiver will drive the throttle

channel to the neutral position. If the receiver is powered on prior to turning on the

transmitter, the receiver will enter the failsafe mode, driving the throttle channel to the neutral

position. When the transmitter is turned on, normal control is resumed.

IMPORTANT: Failsafe activates only in the event that signal is lost from the transmitter.

Failsafe will NOT activate in the event that receiver battery power decreases below the

recommended minimums or power to the receiver is lost.

SR6100AT AVC TECHNOLOGY TELEMETRY RECEIVER

AUX CHANNELS

The Aux channels can operate as additional servo channels, or as a power supply

for a personal transponder.

If AVC is active, only 4 channels; Steering, Throttle, AUX3 and AUX4 are operational.

The reaming Aux channels can be used to power a personal transponder or lights.

If AVC is disabled (see DISABLING AVC TECHNOLOGY STABILITY ASSIST FUNCTION),

all 6 channels including the Aux channels can operate as servo channels.

AUX 1 Port

AUX 2 Port

AUX 3 Port

AUX 4 Port

Battery/Programming Port

Throttle Port

Steering Port

Bind Button

FULL THROTTLE

BRAKE/REVERSE

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

RUN TIME

The largest factor in run time is the capacity of the battery pack. A larger mAh rating increases

the amount of run time experienced.

The condition of a battery pack is also an important factor in both run time and speed.

The battery connectors may become hot during driving. Batteries will lose performance

and capacity over time.

Driving the vehicle from a stop to full speed repeatedly will damage the batteries

and electronics over time. Sudden acceleration will also lead to shorter run times.

TO IMPROVE RUN TIMES

• Keep your vehicle clean and well maintained.

• Allow more airﬂow to the ESC and motor.

• Change the gearing to a lower ratio. A lower ratio decreases the operating temperature

of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.

• Use a battery pack with a higher mAh rating.

• Use the optimum charger to charge battery packs (Visit your local hobby dealer for

more information).

PERFORMING A CONTROL DIRECTION TEST

Perform a control test with the vehicle wheels off the ground. If the wheels rotate after the

vehicle is powered ON, adjust the TH Trim knob until they stop. To make the wheels move

forward, pull the trigger. To reverse them, wait for the wheels to stop, then push the trigger.

When moving forward, the wheels should maintain a straight line without any steering wheel

input. If not, adjust the ST Trim knob, so the wheels maintain a straight line without having to

turn the steering wheel.

CHANGING THE TRAVEL ADJUST SETTINGS

Set the travel adjust settings with all four vehicle wheels off the ground. The throttle end point

and brake end point adjustments will cause the wheels to spin at full speed. Have an assistant

safely hold the vehicle securely while adjusting these settings.

CAUTION: Keep hands, hair and all loose clothing away from any moving parts,

especially the wheels, while setting the travel adjust end points. Serious injury may result.

1. Hold the trigger in the full brake position and turn the steering wheel to full right while powering

on the transmitter. The LED ﬂashes rapidly, indicating programming mode is active.

2. Throttle End Point: Continue holding full throttle. Turn the TH TRIM knob to adjust the full

throttle end point.

3. Brake End Point: Hold the trigger in the full brake position. Turn the TH TRIM knob to adjust

the full brake end point. Return the trigger to the center position.

4. Left Steering End Point: Hold the steering wheel in the full left position. Turn the ST TRIM

knob to adjust the left end point.

5. Right Steering End Point: Hold the steering wheel in the full right position. Turn the ST TRIM

knob to adjust the right end point. Return the steering wheel to the center position.

6. Power off the transmitter to save the travel adjust settings.

The minimum Travel is 75%, and the Maximum travel is 150%.

IMPORTANT: If the travel is changed on the DX2E, you must rebind and calibrate the SRS6100AT.

SPECIFICATIONS

Type Sensorless, SMART Throttle Compatible

Output 130A/760A

Function Forward/Brake–Forward/Brake Reverse

Input Voltage 7.4V–14.8V

BEC Output 6V/4A

Dimensions (LxWxH) 57.5mm x 46mm x 38mm

Weight 154 g

ESC LED STATUS

• No ESC LEDs will glow when there is no throttle input from the transmitter.

• The red ESC LED glows when there is any throttle input from the transmitter.

AUDIBLE WARNING TONES

1. Input Voltage: The ESC checks the in put voltage when it is powered ON. If a voltage

problem is detected, the ESC continuously sounds 2 beeps with a 1 second pause

(xx-xx-xx). Power OFF the ESC and ensure the connections are secure and that

the battery power is not too low for safe operation.

2. Radio Connection: The ESC checks radio signal input when it is powered ON.

If a problem is detected, the ESC continuously sounds 1 beep with a 2 second pause

(x--x--x). Power OFF the ESC and ensure the radio system is operating correctly.

NOTICE: Always disconnect the battery from the ESC after operating your vehicle. The ESC’s

switch only controls power to the receiver and servos. The ESC will continue to draw current when

connected to the battery, resulting in possible damage to the battery through over discharge.

ESC CALIBRATION PROCEDURE

Complete the transmitter/receiver binding procedure prior to calibrating the ESC.

1. Set the transmitter throttle channel to 100% travel and center the throttle trim.

2. Connect a battery to the ESC battery lead.

3. Power on the transmitter.

4. Press and hold the SET button while turning on the ESC. Release the SET button when

the red LED begins to ﬂash, indicating the ESC is in calibration mode. The ESC will enter

programming mode if the button is held for more than three seconds.

TIP: The red LED should be ﬂashing when the ESC enters calibration mode. If the green LED

is ﬂashing the ESC has entered programming mode. Power off the ESC and repeat step 4,

releasing the SET button when the red LED begins to ﬂash.

5. With the transmitter throttle trigger at the neutral position, press and release the ESC SET

button. The red LED will stop ﬂashing, the green LED will ﬂash one time and the motor will

make a tone to indicate the neutral position has been accepted.

6. While holding the throttle trigger at the full throttle position, press and release the ESC SET

button. The green LED will ﬂash twice and the motor will make two tones to indicate the full

throttle position has been accepted.

7. While holding the throttle trigger at the full brake position, press and release the SET button.

The green LED will ﬂash three times and the motor will make three tones to indicate the full

brake position has been accepted.

The motor will operate normally after calibration is completed.

SPEKTRUM

™

FIRMA

™

SMART 130A BRUSHLESS ESC (SPMXSE1130)

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

DESCRIPTIONS

1. Running Mode

- Forward Only with Brake

Intended for competition use, this mode allows only forward and brake controls.

- Forward/Reverse with Brake

This mode is the basic all-around mode, allowing forward, reverse and brake controls.

To engage reverse while moving forward, apply the brake until the vehicle has come to

a complete stop, release brake, then apply the brake again. While braking or in reverse,

engaging the throttle will result in the vehicle immediately accelerating forward.

2. Drag Brake Force

Adjusts the amount of brake automatically applied when the throttle is returned to the

neutral position. This simulates the engine braking effect of a full-scale vehicle, allowing

improved turn-in and your vehicle’s general response to controls.

3. Low Voltage Cutoff

This function helps to prevent battery over-discharge. The ESC continuously monitors the

battery’s voltage. If the voltage falls below the voltage threshold for 2 seconds, the output

power shuts off and the red LED ﬂashes twice repeatedly.

The cutoff threshold calculation is based on individual Li-Po cell voltage. For Ni-MH batteries,

if the voltage battery pack is higher than 9.0V, it will be treated as a 3-cell Li-Po battery

pack; if it is lower than 9.0V, it will be treated as a 2-cell Li-Po battery pack. Example: for a

8.0V Ni-MH battery pack used with a 2.6V/cell threshold, it will be treated as a 2-cell Li-Po

battery pack and the low-voltage cut-off threshold will be 5.2V (2.6x2=5.2).

4. Start Mode (Punch)

Sets the initial throttle punch when the car accelerates. Level 1 gives

a very soft initial acceleration and level 4 gives a stronger initial acceleration.

5. Max Brake Force

Adjusts the maximum braking force. A higher value provides stronger braking,

but can also cause the wheels to lock, resulting in loss of control of the car.

6. Max Reverse Force

This parameter adjusts the maximum power when travelling in reverse.

7. Initial Brake Force (minimum brake)

Adjusts the minimum amount of braking power when the brakes engage. The default value

is equal to the drag brake value. A high value can lock the wheels when the brake is used.

8. Neutral Range

Adjusts the throttle sensitivity around the neutral point. A higher value results in the

throttle having to be moved more for the vehicle to move forward, backward or brake.

9. Timing

Adjusts the motor drive current timing. More timing gives more performance, but can

lower efﬁciency and cause damage to the motor and/or ESC by overload or overheating.

NOTICE: Always ensure the motor timing is set correctly. Failure to set the motor timing

correctly can result in damage to the motor and ESC. Refer to the manufacturer instructions

for recommended timing settings.

10. Motor Type

11. Motor Rotation

Allows you to make this change in the ESC so no wires need to be changed between the

ESC and the motor.

12. Li-Po Cells

Allows the ESC to automatically detect or manually set the number of cells in your Li-Po

battery back.

Default Settings

ESC FUNCTIONS AND MODES

The ESC includes programming options so you can adjust the way your vehicle performs. Refer to the included programming table to adjust the ESC for your driving conditions.

PROGRAMMING TABLE

PROGRAMMING VALUE

PROGRAMMING ITEMS 1 2 3 4 5 6 7 8 9

1. Running Mode Forward w/ brake

Forward/Reverse

w/ brake

Forward/Reverse

2. Drag Brake Force 0% 5% 10% 20% 40% 60% 80% 100%

3. Low Voltage Cutoff non-protection 2.6V/Cell 2.8V/Cell 3.0V/Cell 3.2V/Cell 3.4V/Cell

4. Start Mode Level 1 Level 2 Level 3 Level 4 Level 5 Level 6 Level 7 Level 8 Level 9

5. Max Brake Force 25% 50% 75% 100% disable

6. Max Reverse Force 25% 50% 75% 100%

7. Initial Brake Force = Drag Brake 0% 20% 40%

8. Neutral Range 6% (Narrow) 9% (Normal) 12% (Wide)

9. Timing 0.00º 3.75º 7.50º 11.25º 15.00º 18.75º 22.50º 26.25º

10. Motor Rotation Counterclockwise Clockwise

11. Li-Po Cells Auto Calculate 2 Cells 3 Cells 4 Cells 5 Cells 6 Cells

ESC PROGRAMMING PROCEDURE

Programming is accomplished using the SET button on the ON/OFF switch*.

1. Connect a fully charged battery to the ESC.

2. Power on the transmitter.

3. Power on the ESC.

4. Hold the SET button until the green LED ﬂashes. Release the set button to enter

programming mode.

TIP: To reset all programming items to the default values, press and hold the set button for

ﬁve seconds

5. Press and release the set button as needed to cycle through the programming items. The

number of times the green LED ﬂashes equals the programming item number given in the

programming table.

6. When at the desired programming item, press and hold the set button until the red LED

ﬂashes to select the item.

7. Press and release the SET button to cycle through the values available for the programming

item based on the number of times the LED ﬂashes. Refer to the programming table.

8. Save the setting by pressing and holding the SET button for 3 seconds.

9. Power off the ESC to exit programming mode or to change other programming items.

* Other programming options include the Spektrum SMART Firma ESC Programming Box (SPMXCA200) and the SmartLink USB updating and programmer application. See SpektrumRC.com for

more details about Spektrum SMART Firma ESCs.

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

PRECAUTIONS

• Never touch moving parts.

• Never disassemble while the batteries are installed.

• Always let parts cool before touching.

GEARING

Your vehicle has been equipped with the optimal gearing installed for the use of a 4S battery.

It offers an ideal balance between speed, power and efﬁciency. Should you decide to

customize your vehicle with a 3S battery it is necessary to change to the 14T pinion (included).

Installing a pinion gear with fewer teeth or a spur gear with more teeth will provide greater

torque but will reduce top speed. Likewise, a pinion gear with more teeth or a spur gear with

fewer teeth will reduce torque and increase top speed. Care should be taken when installing

larger pinion gears as this can "overgear" the vehicle, resulting in overheating of the motor

and ESC. When testing different gearing options, pay close attention to the temperature

of the motor and speed control to ensure you are operating within the temperature range

of the components. The motor or ESC should never be so hot that it cannot be touched. If

temperatures are too hot, a different gearing combination with a lower pinion gear and/or

higher spur gear is suggested.

CHANGING THE PINION GEAR/GEAR RATIO

1. Remove the screw holding the pinion gear cover in place.

2. Loosen the set screw and remove the installed pinion gear.

3. Loosen the motor screws and slide the motor back.

4. Place the new pinion on the end of the motor shaft so the set screw is located

over the ﬂat on the shaft.

5. Position it so the teeth line up with the spur gear and secure the pinion by tightening

the set screw.

6. Set the gear mesh.

SPEKTRUM

™

FIRMA

™

1900KV BRUSHLESS MOTOR

SETTING THE GEAR MESH

The gear mesh has already been set at the factory. Setting it is only necessary when changing

motors or gears.

Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When

the gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If

the mesh is too tight, speed could be limited and the motor and ESC will overheat.

1. Loosen the motor screws and slide the motor back.

2. Put a small piece of paper between the pinion and spur gears.

3. Push the gears together while tightening the motor screws.

4. Remove the paper. Check the mesh at 3–5 different locations around

the spur gear for a small amount of movement.

5. Install the gear cover.

NOTICE: If you are using a 3S Li-Po battery, use the included 14T Pinion gear. If you are

using a 4S Li-Po battery, use the installed 12T pinion gear. Using a 14T pinion gear with a

4S Li-Po battery will result in damage to the ESC and motor.

TELEMETRY SETTINGS

If using the Spektrum Dashboard app or the optional speedometer module on your

transmitter, set the motor pole count to 4 and the rollout distance to 1.5" (38.1mm).

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

Vehicle does not operate

Battery not charged or plugged in Charge battery/plug in

ESC switch not “On” Turn on ESC switch

Transmitter not “On” or low battery Turn on/replace batteries

Motor runs but wheels

do not rotate

Pinion not meshing with spur gear Adjust pinion/spur mesh

Pinion spinning on motor shaft Tighten pinion gear setscrew on motor shaft ﬂat spot

Transmission gears stripped Replace transmission gears

Drive pin broken Check and replace drive pin

Steering does not work

Servo plug not in receiver properly Make sure the steering servo plug is connected to the receiver steering channel, noting proper polarity

Servo gears or motor damaged Replace or repair servo

Will not turn one direction Servo gears damaged Replace or repair servo

Motor does not run

Motor wire solder joint is damaged Resolder the motor wire with the proper equipment

Motor wire broken Repair or replace as needed

ESC damaged Contact Horizon Hobby Product Support

ESC gets hot

Motor over-geared Use smaller pinion or larger spur gear

Driveline bound up Check wheels and transmission for binding

Poor run time and/or sluggish

acceleration

Battery pack not fully charged Recharge battery

Charger not allowing full charge Try another charger

Driveline bound up Check wheels, transmission for binding

Poor range and/or glitching

Transmitter batteries low Check and replace

Vehicle battery low Recharge battery

Loose plugs or wires Check all wire connections and plugs

LIMITED WARRANTY

What this Warranty Covers

Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the

“Product”) will be free from defects in materials and workmanship for a period of 2 years from

the date of purchase.

What is Not Covered

This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due

to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use,

installation, operation or maintenance, (iii) modiﬁcation of or to any part of the Product, (iv)

attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product

not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable

technical regulations or (vii) use that violates any applicable laws, rules, or regulations.

OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY

OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES,

INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY

MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

Purchaser’s Remedy

Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon

will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be

defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty

claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase

is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS

WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.

Limitation of Liability

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,

REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,

NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS

BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability

of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon

has no control over use, setup, ﬁnal assembly, modiﬁcation or misuse, no liability shall be

assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly,

the user accepts all resulting liability. If you as the purchaser or user are not prepared to

accept the liability associated with the use of the Product, purchaser is advised to return the

Product immediately in new and unused condition to the place of purchase.

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER • INSTRUCTION MANUAL

Country of Purchase Horizon Hobby Contact Information Address

United States of America

Horizon Service Center (Repairs and Repair Requests) servicecenter.horizonhobby.com/RequestForm/

2904 Research Rd.

Champaign, Illinois, 61822 USA

Horizon Product Support (Product Technical Assistance)

productsupport@horizonhobby.com

877-504-0233

Sales

websales@horizonhobby.com

800-338-4639

European Union

Horizon Technischer Service

service@horizonhobby.eu

+49 (0) 4121 2655 100

Hanskampring 9

D 22885 Barsbüttel, Germany

Sales: Horizon Hobby GmbH

WARRANTY AND SERVICE CONTACT INFORMATION

Law

These terms are governed by Illinois law (without regard to conﬂict of law principals). This

warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state

to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

Your local hobby store and/or place of purchase cannot provide warranty support or service.

Once assembly, setup or use of the Product has been started, you must contact your local

distributor or Horizon directly. This will enable Horizon to better answer your questions and

service you in the event that you may need any assistance. For questions or assistance, please

visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll

free telephone number referenced in the Warranty and Service Contact Information section to

speak with a Product Support representative.

Inspection or Services

If this Product needs to be inspected or serviced and is compliant in the country you live

and use the Product in, please use the Horizon Online Service Request submission process

found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA)

number. Pack the Product securely using a shipping carton. Please note that original boxes

may be included, but are not designed to withstand the rigors of shipping without additional

protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels,

as Horizon is not responsible for merchandise until it arrives and is accepted at our facility.

An Online Service Request is available at http://www.horizonhobby.com/content/service-

center_render-service-center. If you do not have internet access, please contact Horizon

Product Support to obtain a RMA number along with instructions for submitting your product

for service. When calling Horizon, you will be asked to provide your complete name, street

address, email address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the included

items, and a brief summary of the problem. A copy of your original sales receipt must be

included for warranty consideration. Be sure your name, address, and RMA number are clearly

written on the outside of the shipping carton.

NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a

Li-Po battery, please contact the appropriate Horizon Product Support ofﬁce.

Warranty Requirements

For Warranty consideration, you must include your original sales receipt verifying

the proof-of-purchase date. Provided warranty conditions have been met, your Product

will be serviced or replaced free of charge. Service or replacement decisions are at the sole

discretion of Horizon.

Non-Warranty Service

Should your service not be covered by warranty, service will be completed and

payment will be required without notiﬁcation or estimate of the expense unless

the expense exceeds 50% of the retail purchase cost. By submitting the item for

service you are agreeing to payment of the service without notiﬁcation. Service estimates are

available upon request. You must include this request with your item submitted for service.

Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you

will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as

Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for

service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.

horizonhobby.com/content/service-center_render-service-center.

ATTENTION: Horizon service is limited to Product compliant in the country of

use and ownership. If received, a non-compliant Product will not be serviced.

Further, the sender will be responsible for arranging return shipment of the un-

serviced Product, through a carrier of the sender’s choice and at the sender’s

expense. Horizon will hold non-compliant Product for a period of 60 days from

notiﬁcation, after which it will be discarded.

10/15

FCC INFORMATION

FCC ID: CONTAINS BRWKATY1T | FCC ID: CONTAINS BRWSR6100AT

Supplier’s Declaration of Conformity

LOSI LASERNUT ULTRA 4 ROCK RACER, RTR: 1/10 4WD (LOS03028)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

CAUTION: changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC

2904 Research Rd.,

Champaign, IL 61822

Email: [email protected]

Web: HorizonHobby.com

COMPLIANCE INFORMATION

FOR THE EUROPEAN UNION

IC INFORMATION

IC: CONTAINS 6157A-KATY1T | CONTAINS 6157A-SR6100AT

CAN ICES-3 (B)/NMB-3(B)

This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation,

Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to

the following 2 conditions:

This device may not cause interference.

This device must accept any interference, including interference that may cause undesired

operation of the device.

EU Compliance Statement:

LOSI LASERNUT ULTRA 4 ROCK RACER, RTR: 1/10 4WD (LOS03028)

Hereby, Horizon Hobby, LLC declares that the device is in compliance with the

following: EU Radio Equipment Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

https://www.horizonhobby.com/content/support-render-compliance.

Transmitter:

Frequency Band: 2402.0–2478.0 MHz

Max EIRP: 17.5 dBm

Receiver:

Frequency Band: 2402-2478 MHz

Max EIRP: 20 dBm

EU Manufacturer of Record:

Horizon Hobby, LLC

2904 Research Road

Champaign, IL 61822 USA

EU Importer of Record:

Horizon Hobby, GmbH

Hanskampring 9

22885 Barsbüttel Germany

WEEE NOTICE:

This appliance is labeled in accordance with European Directive 2012/19/EU

concerning waste of electrical and electronic equipment (WEEE). This label

indicates that this product should not be disposed of with household waste. It

should be deposited at an appropriate facility to enable recovery and recycling.

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI

Part # English Deutsch Français Italiano

LOS230072 Body Clip Leash (4) Gehäuseklemme Schnur (4) Laisse de clip de carrosserie (4) Lacci per clip per carrozzeria (4)

LOS230075 Body Set, Blue, Painted Karosseriesatz, blau, lackiert Carrosserie, bleue, peinte Kit carrozzeria a vernice blu

LOS230076 Body Set, Red, Painted Karosseriesatz, rot, lackiert Carrosserie, rouge, peinte Kit carrozzeria a vernice rossa

LOS230077 Body Set, Clear Karosseriesatz, farblos Carrosserie, transparente Kit carrozzeria trasparente

LOS230078 Cage Set Käﬁgsatz Ensemble cage Kit scocca

LOS230079 LED, Cage Parts LED, Käﬁgteile LED, pièces de la cage Parti scocca, LED

LOS230080 Spare Tire Rack Ersatzreifenstange Support de pneu de secours Porta ruota di ricambio

LOS231026 Steering Bellcrank Set Steuerungsumlenkhebelsatz Ensemble leviers de renvoi de direction Kit squadrette di sterzo

LOS231027 Steering Posts, Tubes & Hardware Lenksäulen, Rohre und Hardware

Colonnes de direction, tubes et

accessoires

Supporti, tubi e bulloneria dello sterzo

LOS231030 Chassis Support Set Karosserieträgersatz Ensemble support de châssis Kit supporti telaio

LOS231031 Motor Mount Motorhalterung Support moteur Supporto motore

LOS231033 Steering Drag Link & Hardware Lenkzwischenstange & Hardware

Barre d’accouplement de la direction &

accessoires

Tirante di sterzo e bulloneria

LOS231057 Rod Ends & Links Stangenende und Verbindungen Embouts de bielle et liaisons Teste a snodo e aste

LOS231062 Aluminum Chassis Aluminiumchassis Châssis en aluminium Telaio in alluminio

LOS231063 Side Guards Seitenschutze Protections latérales Protezioni laterali

LOS231064 Top Deck, Battery Mount Oberdeck, Akkuhalterung Pont supérieur, support de batterie Piano superiore, supporto batteria

LOS231065 Grid Set Halterungssatz Ensemble grille Kit griglia

LOS232023 Diff Case Set Differentialgehäusesatz Ensemble boîtier de différentiel Kit scatola diff.

LOS232024 Center Drive Coupler Zentrale Antriebskupplung Coupleur d’entraînement central Attacco albero trasmissione

LOS232025 40T Spur Gear, Mod 1 40T-Stirnrad, Mod 1 Engrenage cylindrique 40 dents, Mod 1 Corona 40T, Mod 1

LOS232026 Diff Housing Diffentialgehäuse Logement du différentiel Carter differenziale

LOS232027 Front Ring & Pinion Gear Set Vorderer Ring- und Zahnradgetriebesatz

Ensemble anneau et engrenage à

pignons avant

Kit pignone e corona anteriori

LOS232028 Rear Ring & Pinion Gear Set Hinterer Ring- und Zahnradgetriebesatz

Ensemble anneau et engrenage à

pignons arrière

Kit pignone e corona posteriori

LOS232029 Diff Gear Set w/Hardware Differentialgetriebesatz mit Hardware

Ensemble engrenage de différentiel avec

accessoires

Kit ingr. diff. con bulloneria

LOS232030 Outdrive, Diff (2) Flexwelle, Diff (2) Entraînement extérieur, différentiel (2) Outdrive, diff.(2)

LOS232031 Wheel Hex Set (4) Sechskantradsatz (4) Ensemble écrous hexagonaux de roue (4) Kit esagoni ruote (4)

LOS232032 Front/Rear Driveshafts (2) Front/Heck Antriebswellen (2) Arbres de transmission avant/arrière (2) Alberi trasmissione ant./post. (2)

LOS232033 Front Center Dogbone (1) Vorderes mittiges Dogbone (1) Dogbone central avant (1) Cardano centrale ant. (1)

LOS232034 Rear Center Dogbone (1) Hinteres mittiges Dogbone (1) Dogbone central arrière (1) Cardano centrale post. (1)

LOS232054 Center Dogbone Set Mittiger Dogbone-Satz Ensemble dogbone central Kit cardano centrale

LOS232055 Aluminum Diff Case Aluminium-Differentialgehäuse Ensemble différentiel en aluminium Scatola diff. in alluminio

LOS233011 Shock Plastics Set Kunststoff-Stoßdämpfersatz Ensemble plastiques d’amortisseur Kit plastiche ammortizzatori

LOS233013 Spring Set Federnsatz Ensemble ressort Kit molle

LOS233014 Rear Shock Shaft (2) Hintere Kolbenstange (2) Arbre d’amortisseur arrière (2) Albero amm. post. (2)

LOS233015 Front Shock Shaft (2) Vordere Kolbenstange (2) Arbre d’amortisseur avant (2) Albero amm. ant. (2)

LOS233025 Adjuster Nut Einstellmutter Écrou de réglage Dado di registrazione

LOS233026 Aluminum Shock Caps Aluminium Stoßdämpferkappen Capuchons d’amortisseur en aluminium Tappi amm. in alluminio

LOS233027 Aluminum Front Shock Bodies Vordere Stoßdämpfergehäuse, Aluminium Corps d’amortisseur avant en aluminium Carcasse amm. in alluminio ant.

LOS233028 Aluminum Rear Shock Bodies Hintere Stoßdämpfergehäuse, Aluminium Corps d’amortisseur arrière en aluminium Carcasse amm. in alluminio post.

LOS234016 Front Arm Set Vorderarmsatz Ensemble bras avant Kit braccio anteriore

LOS234017 Rear Arm Set Hinterarmsatz Ensemble bras arrière Kit braccio posteriore

LOS234018 Front Spindle & Carrier Set Front-Spindel- & Trägersatz Ensemble axe et support avant Kit fuselli e portafuselli ant.

LOS234019 Front/Rear Pin Mount Cover Set

Vorderer/Hinterer Stift

Halterungsabdeckungssatz

Ensemble cache de support axe FR/R Kit protezione montanti perni ant/post.

LOS234020 Rear Hub Set Hinterradnabensatz Ensemble moyeu arrière Kit mozzi posteriori

LOS234021 Hingepin & Kingpin Set Scharnierstift & Sattelzapfensatz

Ensemble axe de charnière et axe de

pivot

Kit perni e cardini

LOS234023 Pivot Pin Mount Set, Steel (4) Drehzapfensatz, Stahl (4) Ensemble support axe de pivot, acier (4) Kit supporto perno girevole, acciaio (4)

LOS234035 Aluminum Front Shock Tow Vordere Aluminium-Stoßdämpferbrücke Tour d’amortisseur avant en aluminium Torre amm. in alluminio, ant.

LOS234036 Aluminum Rear Shock Tow Hintere Aluminium-Stoßdämpferbrücke Tour d’amortisseur arrière en aluminium Torre amm. in alluminio, post.

LOS234037 Sway Bar Set Schwingen-Set Ensemble barre stabilisatrice Kit barra antirollio

LOS234038 Rear Sway Bar Set Heck Schwingen-Satz Ensemble barre stabilisatrice arrière Kit barra antirollio posteriore

LOS235011 Set Screw, M3 x 3mm Cup Point (10) Stellschraube M3 x 3 mm Ringschneide (10) Vis de ﬁxation M3 x 3 mm Bout cuvette (10) Kit viti, M3 x 3 mm, senza testa (10)

LOS235012 Set Screw, M4 x 4mm Cup Point (10) Stellschraube M4 x 4 mm Ringschneide (10) Vis de ﬁxation M4 x 4 mm Bout cuvette (10) Kit viti, M4 x 4 mm, senza testa (10)

LOS235024 Button Head Screw, M3 x 25mm (10) Rundkopfschraube, M3 x 25mm (10) Vis à tête bombée M3 x 25 mm (10) Viti a testa tonda, M3 x 25 mm (10)

LOS235025 Button Head Screw, M3 x 30mm (10) Rundkopfschraube, M3 x 30mm (10) Vis à tête bombée M3 x 30 mm (10) Viti a testa tonda, M3 x 30 mm (10)

LOS235026 Set Screw, M3 x 4mm Cup Point (10) Stellschraube M3 x 4mm Ringschneide (10) Vis de ﬁxation M3 x 4mm Bout cuvette (10) Kit viti, M3 x 4 mm, senza testa (10)

LOS235027 Set Screw, M3 x 10mm Cup Point (10)

Stellschraube M3 x 10mm

Ringschneide (10)

Vis de ﬁxation M3 x 10mm Bout

cuvette (10)

Kit viti, M3 x 10 mm, senza testa (10)

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

REPLACEMENT PARTS // TEILELISTE // LISTE DES PIÈCES DE RECHANGE // ELENCO DEI RICAMBI

Part # English Deutsch Français Italiano

LOS236000 E-Clips 2.5mm (12) E-Klemmen, 2,5 mm (12) Attaches en E 2,5 mm (12) E-Clip 2,5 mm (12)

LOS236001 3.2 x 7 x .5mm Washer (10) 3,2 x 7 x 5mm Unterlegscheibe (10) Rondelle 3,2 × 7 × 0,5 mm (10) Rondelle 3,2 x 7 x 0,5 mm (10)

LOS237000 12 x 18 x 4mm Ball Bearing (4) 12 x 18 x 4mm, Kugellager (4) Roulement à billes 12 x 18 x 4 mm (4) Cuscinetto a sfera 12 x 18 x 4 mm (4)

LOS237001 10 x 15 x 4mm Ball Bearing (4) 10 x 15 x 4mm, Kugellager (4) Roulement à billes 10 x 15 x 4 mm (4) Cuscinetto a sfera 10 x 15 x 4 mm (4)

LOS237002 5 x 11 x 4mm Ball Bearing (4) 5 x 11 x 4mm, Kugellager (4) Roulement à billes 5 x 11 x 4 mm (4) Cuscinetto a sfera 5 x 11 x 4 mm (4)

LOS43028 Wheel w/BFG Tire, Copper Rad mit BFG-Reifen, Kupfer Roue avec pneu BFG, cuivre Ruota con pneumatico BFG, rame

LOSA3572 1.0 Module Pitch Pinion, 12T 1.0 Modul Getrieberad, 12T Module de pignon de pas 1.0, 12 dents Pignone Modulo 1.0, 12T

LOSA3574 1.0 Module Pitch Pinion, 14T 1.0 Modul Getrieberad, 14T Module de pignon de pas 1.0, 14 dents Pignone Modulo 1.0, 14T

LOSA6940 6 x 12mm Sealed Ball Bearing (4) 6 x 12mm abgedichtetes Kugellager (4)

Roulement à billes hermétique 6 x 12

mm (4)

Cuscinetti a sfera sigillati 6 x 12 mm (4)

SPM2340

DX3 SMART DSMR 3CH Transmitter

w/SR315

DX3 SMART DSMR-Sender mit 3 Kanälen

mit SR315

Émetteur DX3 SMART DSMR 3 canaux

avec SR315

Trasmittente DX3 SMART DSMR 3 CH

con SR315

SPMS614 S614 Metal Gear Servo, 23T WP S614 Metallgetriebeservo 23T WP

Servo à engrenages métalliques S614,

23 dents, étanche

Servo ingr. in metallo S614 23T WP

SPMSR6100AT

SR6100AT DSMR 6CH AVC

Telemetry Surface Receiver

SR6100AT DSMR AVC Telemetrie

Oberﬂächenempfänger mit 6 Kanälen

Récepteur de surface de télémétrie

AVC 6 canaux SR6100AT DSMR

Ricevitore di superﬁcie con telemetria

SR6100AT DSMR 6CH AVC

SPMXSE1130 Firma 130A Brushless Smart ESC

Firma 130 A Bürstenloser Smart-

Geschwindigkeitsregler

Variateur ESC sans balais 130 A Smart

Firma

Smart ESC Firma 130 A Brushless

SPMXSM2200 3668-1900Kv Motor 3668 - 1900Kv Motor Moteur 3668 - 1900Kv Motore 3668 - 1900Kv

TLR5280 Silicone Differential Fluid, 5,000CS Differential-Silikonﬂüssigkeit, 5.000CS Liquide silicone pour différentiel, 5 000 CS Fluido siliconico per differenziale, 5.000 CS

TLR5282 Silicone Differential Fluid, 10,000CS Differential-Silikonﬂüssigkeit, 10.000CS Liquide silicone pour différentiel, 10 000 CS Fluido siliconico per differenziale, 10.000 CS

TLR5284 Silicone Differential Fluid, 20,000CS Differential-Silikonﬂüssigkeit, 20.000CS Liquide silicone pour différentiel, 20 000 CS Fluido siliconico per differenziale, 20.000 CS

TLR5901 Button Head Screw, M3 x 6mm (10) Rundkopfschraube, M3 x 6mm (10) Vis à tête bombée M3 x 6mm (10) Viti a testa tonda, M3 x 6 mm (10)

TLR5902 Button Head Screw, M3 x 8mm (10) Rundkopfschraube, M3 x 8mm (10) Vis à tête bombée M3 x 8mm (10) Viti a testa tonda, M3 x 8 mm (10)

TLR5903 Button Head Screw, M3 x 10mm (10) Rundkopfschraube, M3 x 10mm (10) Vis à tête bombée M3 x 10mm (10) Viti a testa tonda, M3 x 10 mm (10)

TLR5904 Button Head Screw, M3 x 12mm (10) Rundkopfschraube, M3 x 12mm (10) Vis à tête bombée M3 x 12mm (10) Viti a testa tonda, M3 x 12 mm (10)

TLR5905 Button Head Screw, M3 x 18mm (10) Rundkopfschraube, M3 x 18mm (10) Vis à tête bombée M3 x 18mm (10) Viti a testa tonda, M3 x 18 mm (10)

TLR5908 Button Head Screw, M3 x 44mm (4) Rundkopfschraube, M3 x 44mm (4) Vis à tête bombée M3 x 44mm (4) Viti a testa tonda, M3 x 44 mm (4)

TLR5909 Button Head Screw, M3 x 16mm (10) Rundkopfschraube, M3 x 16mm (10) Vis à tête bombée M3 x 16mm (10) Viti a testa tonda, M3 x 16 mm (10)

TLR5910 Button Head Screw, M3 x 14mm (10) Rundkopfschraube, M3 x 14mm (10) Vis à tête bombée M3 x 14mm (10) Viti a testa tonda, M3 x 14 mm (10)

TLR5911 Button Head Screw, M3 x 20mm (10) Rundkopfschraube, M3 x 20mm (10) Vis à tête bombée M3 x 20mm (10) Viti a testa tonda, M3 x 20 mm (10)

TLR5914 Button Head Screw, M2 x 12mm (10) Rundkopfschraube, M2 x 12mm (10) Vis à tête bombée, M2 x 12mm (10) Viti a testa tonda, M2 x 12 mm (10)

TLR5932 Cap Head Screw, M3 x 10mm (10) Inbusschraube, M3 x 10mm (10)

Vis d’assemblage creuse,

M3 x 10mm (10)

Viti a testa cilindrica, M3 x 10 mm (10)

TLR5933 Cap Head Screw, M3 x 12mm (10) Inbusschraube, M3 x 12mm (10)

Vis d’assemblage creuse, M3 x 12mm

(10)

Viti a testa cilindrica, M3 x 12 mm (10)

TLR5962 Flathead Screw, M3 x 10mm (10) Flachkopfschraube, M3 x 10mm (10) Vis à tête plate, M3 x 10mm (10) Viti a testa piana, M3 x 10 mm (10)

TLR5963 Flathead Screw, M3 x 12mm (10) Flachkopfschraube, M3 x 12mm (10) Vis à tête plate, M3 x 12mm (10) Viti a testa piana, M3 x 12 mm (10)

TLR5964 Flathead Screw, M3 x 16mm (10) Flachkopfschraube, M3 x 16mm (10) Vis à tête plate, M3 x 16mm (10) Viti a testa piana, M3 x 16 mm (10)

TLR5965 Flathead Screw, M3 x 20mm (10) Flachkopfschraube, M3 x 20mm (10) Vis à tête plate, M3 x 20mm (10) Viti a testa piana, M3 x 20 mm (10)

TLR6313 Locknut, M3 x .5 x 5.5mm (10) Kontermutter, M3 x 0,5 x 5,5 mm (10) Contre-écrou M3 x 5 x 5,5 mm (10) Controdadi, M3 x 0,5 x 5,5 mm (10)

TLR6352 Washers, M3 (10) Unterlegscheiben, M3 (10) Rondelles, M3 (10) Rondelle, M3 (10)

TLR8202 Body Clips, Black (12) Gehäuseklemmen, schwarz (12) Clips de carrosserie, noir (12) Clip carrozzeria, colore nero (12)

TLR74008 Silicone Shock Oil, 35 wt, 2 oz Stoßdämpfer-Silikonöl, 35 wt, 59 ml (2 oz)

Huile silicone pour amortisseurs, 35 wt,

59 mL

Olio di silicone per ammortizzatori,

35 wt, 60 ml (2 oz)

TLR235007 Flat Head Screw, M2.5 x 10mm (10) Flachkopfschraube M2,5 x 10mm (10) Vis à tête plate M2,5 x 10 mm (10) Smart ESC Firma 130 A Brushless

TLR255008 Button Head Screw, M4 x 16mm (10) Rundkopfschraube, M4 x 16mm (10) Vis à tête bombée, M4 x 16 mm (10) Viti a testa tonda, M4 x 16 mm (10)

TLR255013 Flat Head Screws, M4 x 12mm (10) Rundkopfschrauben, M4 x 12mm (10) Vis à tête plate, M4 x 12mm (10) Viti a testa piana, M4 x 12 mm (10)

TLR256005 Nylock Nut, M4 (10) Nylock-Mutter, M4 (10) Contre-écrou Nylock, M4 (10) Dado Nylock, M4 (10)

TLR336005

M3 Flanged Aluminum Locknut,

Black (10)

M3 Aluminium-Kontermutter mit Flansch,

schwarz (10)

Contre-écrou M3 en aluminium à collet,

noir (10)

Controdado allumino ﬂangiato M3,

nero (10)

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

OPTIONAL PARTS // OPTIONALE TEILE // PIÈCES OPTIONNELLES // PARTI OPZIONALI

Part # English Deutsch Français Italiano

DYN2834 Startup Tool Set: Metric Anfänger-Werkzeugsatz: Metrisch Jeu d’outils de démarrage : Métrique Kit completo attrezzi base: metrico

DYN5500 Magnum Force 2 Motor Spray, 13 oz Magnum Force 2 Motorspray, 368 g

Vaporisateur pour moteur Magnum Force

2, 368 g

Spray per motore Magnum Force 2,

385 ml (13 oz)

DYNT2010 Machined Nut Driver Set (4) Metric Set gefräste Steckschlüssel (4) metrisch

Ensemble tourne-écrou usiné (4)

Métrique

Kit di chiavi (4) metriche

DYNT2030 Machined Hex Driver Set (4) Met

Set gefräste Inbusschraubendreher

(4) Met

Ensemble clé à six pans usinée (4)

Métrique

Kit di chiavi a brugola (4) metriche

LOS331012 Mach Alum Motor Mount Gefräste Motorhalterung, Aluminium Support moteur en aluminium usiné Supporto motore in alluminio lavorato

LOS334011 Aluminum Rear Hubs (2) Hintere Naben, Aluminium (2) Moyeux arrière en aluminium (2) Mozzi in alluminio, post. (2)

LOS334012 Aluminum Front Spindle (2) Front-Spindel, Aluminium (2) Axe avant en aluminium (2) Fuselli in alluminio, ant. (2)

LOS334013 Aluminum Spindle Carrier (2) Spindelträger, Aluminium (2) Support d’axe en aluminium (2) Portafuselli in alluminio (2)

LOS43011 Desert Claws Tires w/Foam, Soft (2)

Desert Claws-Reifen mit Schaumstoff

(2)

Pneus Desert Claws avec mousse,

douce (2)

Pneumatici Desert Claw con schiuma,

morbidi (2)

LOSA3571 1.0 Module Pitch Pinion,11T 1.0 Modul Getrieberad, 11T Module de pignon de pas 1.0, 11 dents Pignone Modulo 1.0, 11T

LOSA3573 1.0 Module Pitch Pinion, 13T 1.0 Modul Getrieberad, 13T Module de pignon de pas 1.0, 13 dents Pignone Modulo 1.0, 13T

LOSA3576 1.0 Module Pitch Pinion, 16T 1.0 Modul Getrieberad, 16T Module de pignon de pas 1.0, 16 dents Pignone Modulo 1.0, 16T

LOSA3578 1.0 Module Pitch Pinion, 18T 1.0 Modul Getrieberad, 18T Module de pignon de pas 1.0, 18 dents Pignone Modulo 1.0, 18T

LOSA99173 Ride Height Gauge Höhenmesser Jauge de hauteur de course Misuratore altezza di marcia

LOSA99174 Car Stand Fahrzeugständer Socle Supporto automodello

LOSB3493 Aluminum Clamping Wheel Hex Aluminium Klemmrad Sechskant

Roue de serrage hexagonale en

aluminium

Rotella di bloccaggio esagonale in

alluminio

SPM6730 Spektrum Tx Storage Bag* Spektrum Tx Aufbewahrungstasche* Sac de rangement Spektrum Tx* Sacco custodia Tx Spektrum

SPMSS6230 S6230 U-T / M-S Digital WP Servo S6230 U-T/M-S Digitaler WP Servo Servo numérique S6230 U-T / M-S WP

Servo impermeabile digitale S6230

U-T/M-S

TLR332014 Rear Hex, +0.5mm Width, Aluminum

Hinterer Sechskant, +0,5 mm Breite,

Aluminium

Écrou hexagonal arrière, +0,5 mm

de largeur, aluminium

Esagono posteriore, larghezza +0,5 mm,

alluminio

TLR336000

4mm Aluminum Serrated Lock Nut,

Black (6)

4 mm Aluminium Rändelmutter,

schwarz (6)

Contre-écrou en aluminium à embase

striée 4 mm, noir (6)

Controdado dentato in alluminio 4 mm,

nero (6)

TLR336001

4mm Aluminum Serrated Lock Nut,

Blue (6)

4 mm Aluminium Rändelmutter,

blau (6)

Contre-écrou en aluminium à embase

striée 4 mm, bleu (6)

Controdado dentato in alluminio 4 mm,

blu (6)

TLR5062 Bleeder Shock Cap, Aluminum (2)

Stoßdämpfer-Entlüfterkappe,

Aluminium (2)

Contre-écrou en aluminium à embase

striée 4 mm, bleu (6)

Tappi di sﬁato per ammortizzatori,

alluminio (2)

TLR74006 Silicone Shock Oil, 30 wt, 2 oz

Stoßdämpfer-Silikonöl, 30 wt, 59 ml

(2 oz)

Huile silicone pour amortisseurs, 30 WT,

59 mL

Olio di silicone per ammortizzatori, 30

wt, 60 ml (2 oz)

TLR74010 Silicone Shock Oil, 40 wt, 2 oz

Stoßdämpfer-Silikonöl, 40 wt, 59 ml

(2 oz)

Huile silicone pour amortisseurs, 40 WT,

59 mL

Olio di silicone per ammortizzatori, 40

wt, 60 ml (2 oz)

TLR76000 Tire Glue, Standard Reifenklebemittel, Standard Colle de pneu, standard Colla pneumatici, standard

TLR76004 TLR Lok, Threadlock, Blue TLR Lok, Schraubensicherung, blau Verrou TLR, frein-ﬁlet, bleu TLR Lok, frenaﬁletti, blu

Part # English Deutsch Français Italiano

DYNC2005CA Prophet Sport LiPo 35W AC Charger Prophet Sport LiPo 35 W AC-Ladegerät Chargeur CA Li-Po 35 W Prophet Sport

Caricabatterie Prophet Sport LiPo

35 W CA

SPMXC1080 Spektrum Smart S100 AC Charger

Spectrum Smart S100 Wechselstrom-

Ladegerät

Chargeur CA Spektrum Smart S100

Caricabatterie Spektrum Smart

S100 CA

SPMX50003S50H5

11.1V 5000mAh 3S 50C Smart

Hardcase LiPo Battery: IC5

11,1 V 5000 mAh 3S 50C Smart

LiPo-Akku, Hartschale: IC5

Batterie LiPo Smart 11,1 V 5 000 mAh

3S 50C, boîtier rigide : IC5

Batteria Li-Po 11,1 V 5000 mAh 3S

50C Smart Hardcase: IC5

SPMX50004S50H5

14.8V 5000mAh 4S 50C Smart

Hardcase LiPo Battery: IC5

14,8 V 5000 mAh 4S 50C Smart LiPo-

Akku, Hartschale: IC5

Batterie LiPo Smart 14,8V 5 000 mAh

4S 50C, boîtier rigide : IC5

Batteria Li-Po 14,8 V 5000 mAh 4S

50C Smart Hardcase: IC5

RECOMMENDED PARTS // EMPFOHLENE TEILE// PIÈCES RECOMMANDÉES // PARTI CONSIGLIATE

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

SPMXSM2200

LOS231064

SPMXSE1130

LOS231054

LOS231062

LOS231063

LOS231064

LOS232029

LOS232025

TLR235007

LOS237000

TLR3100

LOS232030

LOS232054

LOS232023

LOS232030

LOS237000

TLR5901

LOS232055

LOS232026

LOSA3572 (12T)

LOSA3574 (14T)

LOS235024

TLR5905

LOS233014

LOS233015

TLR6313

LOS233011

LOS233013

LOS231030

TLR336005

LOSB2906

LOS233027

LOS233025

LOS233026

LOS233028

LOS236000

LOS235012

TLR6352

TLR235007

LOS234022

LOS234035

LOS234037

LOS234021

LOS234023

LOS234019

TLR5909

TLR5911

TLR5964

LOS234016

LOS234018

LOS237001

LOS234021

LOS234018

LOS232032

TLR5911

LOS231057

TLR6313

TLR5964

LOS231057

TLR6313

TLR5905

LOS235026

LOSA6940

LOS232031

LOS234016

TLR255008

LOS232030

LOS237000

LOS232023

LOS232028

LOS237002

LOS232024

LOS232023

LOS232026

LOS237000

LOS232030

LOS232029

LOS232026

LOS232023

TLR5965

LOS232023

LOS237000

LOS232027

LOS232023

TLR5933

LOS232030

LOS231027

LOS231026

TLR5904

TLR6313

TLR5904

TLR5910

LOS231057

LOS231024

LOS231057

LOS231054

LOS231026

LOS231033

LOS232026

TLR5963

TLR5964

TLR5932

LOS232054

LOS231031

SPMS614

SPMSR6100AT

TLR5904

LOS232029

LOS232023

TLR5904 TLR5964

LOS232027

LOS237002

LOS232024

TLR5911

TLR5905

LOS232031

TLR336000

TLR256005

LOS237001

LOSA6940

LOS234021

LOS234023

TLR255013

TLR5963

LOS234020

LOS234021

TLR6313

LOS234017

LOS234019

LOS234036

TLR235007

TLR5903

TLR5963

LOS235011

LOS231054t

LOS235025

TLR6313

TLR5908

LOS230079

TLR5904

LOS230079

LOS230078

LOS230079

LOS230080

LOS234038

LOS43028

LOS235025

TLR5903

TLR5901

TLR5903

TLR5901

LOS234038

TLR5901

TLR5903

TLR5901

TLR5903

LOS231065

TLR5901

LOS231065

TLR5901

LOS230076

LOS230077

LOS230079

TLR5901

TLR5903

TLR5962

TLR5963

TLR5903

SPMXSM2200

LOS231064

LOS230079

10K

FLUID

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

SPMXSM2200

LOS231064

SPMXSE1130

LOS231054

LOS231062

LOS231063

LOS231064

LOS232029

LOS232025

TLR235007

LOS237000

TLR3100

LOS232030

LOS232054

LOS232023

LOS232030

LOS237000

TLR5901

LOS232055

LOS232026

LOSA3572 (12T)

LOSA3574 (14T)

LOS235024

TLR5905

LOS233014

LOS233015

TLR6313

LOS233011

LOS233013

LOS231030

TLR336005

LOSB2906

LOS233027

LOS233025

LOS233026

LOS233028

LOS236000

LOS235012

TLR6352

TLR235007

LOS234022

LOS234035

LOS234037

LOS234021

LOS234023

LOS234019

TLR5909

TLR5911

TLR5964

LOS234016

LOS234018

LOS237001

LOS234021

LOS234018

LOS232032

TLR5911

LOS231057

TLR6313

TLR5964

LOS231057

TLR6313

TLR5905

LOS235026

LOSA6940

LOS232031

LOS234016

TLR255008

LOS232030

LOS237000

LOS232023

LOS232028

LOS237002

LOS232024

LOS232023

LOS232026

LOS237000

LOS232030

LOS232029

LOS232026

LOS232023

TLR5965

LOS232023

LOS237000

LOS232027

LOS232023

TLR5933

LOS232030

LOS231027

LOS231026

TLR5904

TLR6313

TLR5904

TLR5910

LOS231057

LOS231024

LOS231057

LOS231054

LOS231026

LOS231033

LOS232026

TLR5963

TLR5964

TLR5932

LOS232054

LOS231031

SPMS614

SPMSR6100AT

TLR5904

LOS232029

LOS232023

TLR5904 TLR5964

LOS232027

LOS237002

LOS232024

TLR5911

TLR5905

LOS232031

TLR336000

TLR256005

LOS237001

LOSA6940

LOS234021

LOS234023

TLR255013

TLR5963

LOS234020

LOS234021

TLR6313

LOS234017

LOS234019

LOS234036

TLR235007

TLR5903

TLR5963

LOS235011

LOS231054t

LOS235025

TLR6313

TLR5908

LOS230079

TLR5904

LOS230079

LOS230078

LOS230079

LOS230080

LOS234038

LOS43028

LOS235025

TLR5903

TLR5901

TLR5903

TLR5901

LOS234038

TLR5901

TLR5903

TLR5901

TLR5903

LOS231065

TLR5901

LOS231065

TLR5901

LOS230076

LOS230077

LOS230079

TLR5901

TLR5903

TLR5962

TLR5963

TLR5903

SPMXSM2200

LOS231064

LOS230079

FLUID

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

SPMXSM2200

LOS231064

SPMXSE1130

LOS231054

LOS231062

LOS231063

LOS231064

LOS232029

LOS232025

TLR235007

LOS237000

TLR3100

LOS232030

LOS232054

LOS232023

LOS232030

LOS237000

TLR5901

LOS232055

LOS232026

LOSA3572 (12T)

LOSA3574 (14T)

LOS235024

TLR5905

LOS233014

LOS233015

TLR6313

LOS233011

LOS233013

LOS231030

TLR336005

LOSB2906

LOS233027

LOS233025

LOS233026

LOS233028

LOS236000

LOS235012

TLR6352

TLR235007

LOS234022

LOS234035

LOS234037

LOS234021

LOS234023

LOS234019

TLR5909

TLR5911

TLR5964

LOS234016

LOS234018

LOS237001

LOS234021

LOS234018

LOS232032

TLR5911

LOS231057

TLR6313

TLR5964

LOS231057

TLR6313

TLR5905

LOS235026

LOSA6940

LOS232031

LOS234016

TLR255008

LOS232030

LOS237000

LOS232023

LOS232028

LOS237002

LOS232024

LOS232023

LOS232026

LOS237000

LOS232030

LOS232029

LOS232026

LOS232023

TLR5965

LOS232023

LOS237000

LOS232027

LOS232023

TLR5933

LOS232030

LOS231027

LOS231026

TLR5904

TLR6313

TLR5904

TLR5910

LOS231057

LOS231024

LOS231057

LOS231054

LOS231026

LOS231033

LOS232026

TLR5963

TLR5964

TLR5932

LOS232054

LOS231031

SPMS614

SPMSR6100AT

TLR5904

LOS232029

LOS232023

TLR5904 TLR5964

LOS232027

LOS237002

LOS232024

TLR5911

TLR5905

LOS232031

TLR336000

TLR256005

LOS237001

LOSA6940

LOS234021

LOS234023

TLR255013

TLR5963

LOS234020

LOS234021

TLR6313

LOS234017

LOS234019

LOS234036

TLR235007

TLR5903

TLR5963

LOS235011

LOS231054t

LOS235025

TLR6313

TLR5908

LOS230079

TLR5904

LOS230079

LOS230078

LOS230079

LOS230080

LOS234038

LOS43028

LOS235025

TLR5903

TLR5901

TLR5903

TLR5901

LOS234038

TLR5901

TLR5903

TLR5901

TLR5903

LOS231065

TLR5901

LOS231065

TLR5901

LOS230076

LOS230077

LOS230079

TLR5901

TLR5903

TLR5962

TLR5963

TLR5903

SPMXSM2200

LOS231064

LOS230079

35 WT

OIL

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

SPMXSM2200

LOS231064

SPMXSE1130

LOS231054

LOS231062

LOS231063

LOS231064

LOS232029

LOS232025

TLR235007

LOS237000

TLR3100

LOS232030

LOS232054

LOS232023

LOS232030

LOS237000

TLR5901

LOS232055

LOS232026

LOSA3572 (12T)

LOSA3574 (14T)

LOS235024

TLR5905

LOS233014

LOS233015

TLR6313

LOS233011

LOS233013

LOS231030

TLR336005

LOSB2906

LOS233027

LOS233025

LOS233026

LOS233028

LOS236000

LOS235012

TLR6352

TLR235007

LOS234022

LOS234035

LOS234037

LOS234021

LOS234023

LOS234019

TLR5909

TLR5911

TLR5964

LOS234016

LOS234018

LOS237001

LOS234021

LOS234018

LOS232032

TLR5911

LOS231057

TLR6313

TLR5964

LOS231057

TLR6313

TLR5905

LOS235026

LOSA6940

LOS232031

LOS234016

TLR255008

LOS232030

LOS237000

LOS232023

LOS232028

LOS237002

LOS232024

LOS232023

LOS232026

LOS237000

LOS232030

LOS232029

LOS232026

LOS232023

TLR5965

LOS232023

LOS237000

LOS232027

LOS232023

TLR5933

LOS232030

LOS231027

LOS231026

TLR5904

TLR6313

TLR5904

TLR5910

LOS231057

LOS231024

LOS231057

LOS231054

LOS231026

LOS231033

LOS232026

TLR5963

TLR5964

TLR5932

LOS232054

LOS231031

SPMS614

SPMSR6100AT

TLR5904

LOS232029

LOS232023

TLR5904 TLR5964

LOS232027

LOS237002

LOS232024

TLR5911

TLR5905

LOS232031

TLR336000

TLR256005

LOS237001

LOSA6940

LOS234021

LOS234023

TLR255013

TLR5963

LOS234020

LOS234021

TLR6313

LOS234017

LOS234019

LOS234036

TLR235007

TLR5903

TLR5963

LOS235011

LOS231054t

LOS235025

TLR6313

TLR5908

LOS230079

TLR5904

LOS230079

LOS230078

LOS230079

LOS230080

LOS234038

LOS43028

LOS235025

TLR5903

TLR5901

TLR5903

TLR5901

LOS234038

TLR5901

TLR5903

TLR5901

TLR5903

LOS231065

TLR5901

LOS231065

TLR5901

LOS230076

LOS230077

LOS230079

TLR5901

TLR5903

TLR5962

TLR5963

TLR5903

SPMXSM2200

LOS231064

LOS230079

20K

FLUID

LOSI

TENACITY

LASERNUT ULTRA 4 1/10 4WD RTR ROCK RACER

EXPLODED VIEW // EXPLOSIONSZEICHNUNG // VUE ÉCLATÉE DES PIÈCES // VISTA ESPLOSA DELLE PARTI

SPMXSM2200

LOS231064

SPMXSE1130

LOS231054

LOS231062

LOS231063

LOS231064

LOS232029

LOS232025

TLR235007

LOS237000

TLR3100

LOS232030

LOS232054

LOS232023

LOS232030

LOS237000

TLR5901

LOS232055

LOS232026

LOSA3572 (12T)

LOSA3574 (14T)

LOS235024

TLR5905

LOS233014

LOS233015

TLR6313

LOS233011

LOS233013

LOS231030

TLR336005

LOSB2906

LOS233027

LOS233025

LOS233026

LOS233028

LOS236000

LOS235012

TLR6352

TLR235007

LOS234022

LOS234035

LOS234037

LOS234021

LOS234023

LOS234019

TLR5909

TLR5911

TLR5964

LOS234016

LOS234018

LOS237001

LOS234021

LOS234018

LOS232032

TLR5911

LOS231057

TLR6313

TLR5964

LOS231057

TLR6313

TLR5905

LOS235026

LOSA6940

LOS232031

LOS234016

TLR255008

LOS232030

LOS237000

LOS232023

LOS232028

LOS237002

LOS232024

LOS232023

LOS232026

LOS237000

LOS232030

LOS232029

LOS232026

LOS232023

TLR5965

LOS232023

LOS237000

LOS232027

LOS232023

TLR5933

LOS232030

LOS231027

LOS231026

TLR5904

TLR6313

TLR5904

TLR5910

LOS231057

LOS231024

LOS231057

LOS231054

LOS231026

LOS231033

LOS232026

TLR5963

TLR5964

TLR5932

LOS232054

LOS231031

SPMS614

SPMSR6100AT

TLR5904

LOS232029

LOS232023

TLR5904 TLR5964

LOS232027

LOS237002

LOS232024

TLR5911

TLR5905

LOS232031

TLR336000

TLR256005

LOS237001

LOSA6940

LOS234021

LOS234023

TLR255013

TLR5963

LOS234020

LOS234021

TLR6313

LOS234017

LOS234019

LOS234036

TLR235007

TLR5903

TLR5963

LOS235011

LOS231054t

LOS235025

TLR6313

TLR5908

LOS230079

TLR5904

LOS230079

LOS230078

LOS230079

LOS230080

LOS234038

LOS43028

LOS235025

TLR5903

TLR5901

TLR5903

TLR5901

LOS234038

TLR5901

TLR5903

TLR5901

TLR5903

LOS231065

TLR5901

LOS231065

TLR5901

LOS230076

LOS230077

LOS230079

TLR5901

TLR5903

TLR5962

TLR5963

TLR5903

SPMXSM2200

LOS231064

LOS230079

Losi, Tenacity, Firma, DX3, DSM, DSM2, DSMR, AVC, Active Vehicle Control, Fuze, IC5 and the Horizon Hobby logo are trademarks or

registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc.

The Lasernut name and logo and vehicle cage design are property of Cody Waggoner, used under license.

All other trademarks, service marks and logos are property of their respective owners.

US 9,320,977, US 10,528,060, US 9,930,567. US 10,419,970. US 10,849,013. Other patents pending.

Updated 03/21 | LOS03028

WWW.LOSI.COM

Losi LOS03028T2 Le manuel du propriétaire

Marque: Losi

Modèle: LOS03028T2

Catégorie: Jouets télécommandés

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Losi LOS03028T2 Owner's manual

Losi LOS03028T2 Le manuel du propriétaire

Ce manuel convient également à

Losi LOS03028T2 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents