Rotel RSP-1576MKII Le manuel du propriétaire

STANDBYSTANDBY

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

Owner’s Manual

Manuel de l’utilisateur

Bedienungsanleitung

Manual de Instrucciones

Gebruikershandleiding

Manuale di istruzioni

Bruksanvisning

Инструкция пользователя

RSP-1576MKII

Surround Sound Processor

Processeur Audio Surround

Surround-Prozessor

Procesador de Sonido Envolvente

Surround sound-processor

Processore Surround

Surroundprocessor

Процессор окружающего звука

2

RSP-1576MKII Surround Sound Processor

Remote Control Overview ...........................................18

Overview of Buttons and Controls .....................................18

STANDBY 1 and Power ON/OFF Buttons A 18

VOLUME Knob and VOLUME UP/DOWN Buttons =D 18

DISPLAY (DISP) Button 0B 18

SETUP Button H 18

Navigation and ENTER Buttons I 18

MUTE Button -F 18

Input Buttons 4qM 18

SUR+ Buttons 9B 18

Playback Control buttons L 18

DIM Button J 18

SUB, CTR, REAR Buttons B 18

MEM Button E 18

LIGHT Button N 18

ASSISTIVE LIGHT O 18

Automatic Surround Modes ...........................................18

Manually Selecting Surround Modes ....................................19

Digital Audio 19

Analog Stereo 19

Basic Operation ...................................................19

Selecting Inputs 19

USB/iPod Operation ...............................................20

iPod/iPhone Connection 0 20

Playback Control Buttons L 20

Bluetooth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Bluetooth Connection 20

Rear PC-USB .....................................................20

Rear PC-USB Connection 20

Setup ..........................................................20

Menu Basics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Navigation Buttons 20

Main Menu 20

Conﬁguring Inputs .................................................20

Input Setup 21

Multi Input Setup 22

Conﬁguring Audio ..................................................22

Audio Conguration 22

Conﬁguring Speakers and Audio .......................................22

Speaker Conguration 23

Advanced Speaker Setup 24

Subwoofer Setup 24

Speaker Level Setup 25

Speaker and Delay/Distance Setup 25

Miscellaneous Settings ..............................................26

System Setup 26

Video Setup 27

Troubleshooting ...................................................27

Specications .....................................................28

Contents

Important Safety Instructions ..........................................4

Figure 1: Control and Connections 5

Figure 2: Remote Control 6

Figure 3: Amplier And Subwoofer 7

Figure 4: Digital Audio and PC-USB Connections 8

Figure 5: Blu-Ray and Video Player Connections 8

Figure 6: Front USB Connections 9

Figure 7: CD Player Connections 9

Figure 8: Tuner Connections 10

Figure 9: Front HDMI Connections 10

Figure 10: Rear HDMI Connections 11

On-Screen Menus 12

About Rotel ......................................................13

Getting Started ...................................................13

Video Features 13

Audio Features 13

Surround Features 13

Other Features 13

Unpacking 13

Placement 13

Overview of Connections ............................................14

HDMI Inputs and Outputs ............................................14

Rear HDMI IN 1–6 Video Inputs r 14

Front HDMI IN 6 14

HDMI Monitor Outputs e 14

Audio Inputs and Outputs ............................................14

PHONO Input f 14

TUNER Input f 14

CD Input f 14

AUX Input f 15

BALANCED Input d 15

MULTI Input g 15

PREAMP Output h 15

DIGITAL Inputs w 15

PC-USB Input t 15

Front USB Input 5 15

Other Connections .................................................15

AC Input j 15

Master Power Switch a 15

12V TRIGGER Output i 15

REM IN Jack o 16

IR OUT Jacks p 16

Rotel Link [ 16

Rear USB Power Port \ 16

RS232 Connector y 16

NETWORK Connector u 16

Making Connections ................................................16

Connecting an External Amplier 16

Connecting a Subwoofer 16

Connecting a DVD, Blu-ray, Cable, Satellite, Game Console and HDTV Tuner 16

Connecting a Blu-ray or DVD Player 17

Connecting a Display 17

Connecting a CD Player or XLR Source 17

Connecting a Tuner 17

Connecting an iPod/iPhone 17

Front Panel Overview ..............................................17

Front Panel Display 3 17

IR Remote Sensor 2 17

3

Rotel products are designed to comply with international

directives on the Restriction of Hazardous Substances

(RoHS) in electrical and electronic equipment and

the disposal of Waste Electrical and Electronic

Equipment (WEEE). The crossed wheelie bin symbol

indicates compliance and that the products must be

appropriately recycled or processed in accordance

with these directives.

STANDBYSTANDBY

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

1

2

3

Pin Assignments

Balanced Audio (3 pole XLR):

Pin 1: Ground / Screen

Pin 2: In phase / +ve / Hot

Pin 3: Out of phase / -ve / Cold

4

RSP-1576MKII Surround Sound Processor

Notice

The RS232 connection should be handled by authorized persons only.

WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel.

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do

not expose the unit to dripping or splashing. Do not place objects filled with liquids, such as vases, on the

unit. Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign

object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a

qualified service person for inspection and necessary repairs.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The

wide blade or the third prong are provided for your safety. If the provided plug does not fit into your

outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

Only use attachments/accessories specified by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or

sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tipping over.

Unplug this apparatus during lightning storms or when unused for long periods of time.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate

normally, or has been dropped.

The apparatus should be used in non tropical climate.

The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers,

table-cloths, curtains, etc.

No open flame sources, such as lighted candles, should be placed on the apparatus.

Touching uninsulated terminals or wiring may result in an unpleasant sensation.

You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit.

WARNING: The rear panel power cord connector is the mains power disconnect device. The device must

be located in an open area that allows access to the cord connector.

The unit must be connected to a power supply only of the type and voltage specified on the rear panel.

(USA: 120 V/60Hz, EC: 230V/50Hz)

Connect the component to the power outlet only with the supplied power supply cable or an exact equivalent.

Do not modify the supplied cable. Do not use extension cords.

The mains plug is the disconnect of the unit. In order to completely disconnect the unit from the supply

mains, remove the main plug from the unit and the AC power outlet. This is the only way to completely

remove mains power from the unit.

The main plug is used as the main disconnect device and should remain readily accessible.

The batteries in remote control shall not be exposed to excessive heat such as sunshine, fire or the like.

Batteries should be recycled or disposed as per state and local guidelines.

WARNING: The master power switch is located on the rear panel. The unit must allow unobstructed

access to the main power switch.

Important Safety Instructions

FCC Information

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction, may cause harmful interference

to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.(TV, radio, etc.).

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for additional help.

Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following to conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

interference in a residential installation. This equipment generates and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions, may cause interference to radio or TV

communications. There is no guarantee that interference will not occur in a particular installation. If this

equipment does cause interference to radio or television reception, which can be determined by turning

the equipment off and on, try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the unit and the television tuner.

• Connect the unit to an AC power outlet on a different electrical circuit.

• Consult your authorized Rotel retailer for assistance.

DAB

5

STAND BYSTAND BY

HDMI

MUTE2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

PUSH

ON

OFF

j

h

g

f

d

3

1 2

4

e i

\

a

]

[

p

o

uyt

r

6

789

0

-

q

w

5

s

=

Figure 1: Control and Connections

Commandes et Connexions

Bedienelemente und Anschlüsse

Controles y Conexiones

Bedieningselementen en aansluitingen

Controlli e connessioni

Kontroller och anslutningar

Органы управления и соединения

6

RSP-1576MKII Surround Sound Processor

O

L

M

H

A

C

D

E

G

J

K

F

N

A

B

I

Figure 2: Remote Control

Télécommande

Fernbedienung

Mando a Distancia

Afstandsbediening

Telecomando

Fjärrkontroll

Пульт дистанционного управления

7

SUBWOOFER

INPUT

REAR LEFT

AMPLIFIER

CB RIGHT (2)

CB LEFT (1)

REAR RIGHT

AMPLIFIER

FRONT LEFT

AMPLIFIER

CENTER

AMPLIFIER

FRONT RIGHT

AMPLIFIER

PUSH

ON

OFF

Figure 3: Amplier And Subwoofer

Amplicateurs et caissons de graves

Verstärker und Subwoofer

Amplicador y Subwoofer

Versterker en subwoofer

Collegamento di amplicatori e subwoofer

Förstärkare och subbas

Усилитель и сабвуфер

8

RSP-1576MKII Surround Sound Processor

PUSH

ON

OFF

CD PLAYER

Computer

OPTICAL

COAXIAL

DIGITAL AUDIO OUTPUT

MULTICHANNEL ANALOG OUTPUT

FRONT R SUBREAR R CENTER FRONT LREAL L

DVD or BLUERAY PLAYER

PUSH

ON

OFF

Figure 4: Digital Audio and PC-USB Connections

Connexions audio numériques et PC-USB

Digitale Audio und PC-USB verbindungen

Conexiones Digitales de Audio y PC-USB

Digitale audio- en PC-USB-aansluitingen

Collegamenti audio digitale e PC-USB

Digitala ljud- och PC-USB-anslutningar

Подсоединения цифрового аудио и PC-USB

Figure 5: Blu-Ray and Video Player Connections

Connexions à un lecteur Blu-Ray ou Vidéo

Anschlussdiagramm für Blu-Ray- und Video-Player

Conexiones para Reproductor de Video o Blu-Ray

Aansluitingen voor een Blu-Ray of Video-speler

Collegamento di lettori Blu-Ray o Video

Blu-Ray- eller Video-spelare

Подключения Blu-Ray или Видео проигрывателя

9

STAND BYSTAND BY

HDMI

MUTE

2CH SUR + DISPLAYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

CD PLAYER

AUDIO OUTPUT

RIGHT LEFT

DIGITAL

ANALOG

BALANCED AUDIO OUTPUT

RIGHT LEFT

PUSH

ON

OFF

Figure 6: Front USB Connections

Connexions USB en face avant

Frontseitiger USB-Anschluss

Conexiones USB del Panel Frontal

USB-aansluiting op het voorpaneel

Ingresso USB frontale

USB-anslutning på fronten

Подключение USB-накопителей к фронтальному порту

Figure 7: CD Player Connections

Connexions à un lecteur de CD

Anschlussdiagramm für einen CD-Spieler

Conexiones para Reproductor de CD

Cd-speleraansluitingen

Collegamento di un lettore CD

CD-spelare

Подключения CD-плеера

10

RSP-1576MKII Surround Sound Processor

AUDIO OUTPUT

RIGHT LEFT

DIGITAL

ANALOG

PUSH

ON

OFF

TUNER

Figure 8: Tuner Connections

Connexions à un tuner

Anschlussdiagramm für einen Tune

Conexiones para Sintonizador

Aansluitingen voor Tuner

Collegamento di un Sintonizzatore

Tuner Anslutning

Подключение Тюнера

STAND BYSTAND BY

HDMI

MUTE

2CH SUR + DISPL AYBYPASS

VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 VIDEO 6 VIDEO 7

USB PC-USB XLR TUNER CD PHONO BT

5V 2.1A

Figure 9: Front HDMI Connections

Connexions HDMI avant

Vorderseite HDMI-Verbindungen

Conexiones HDMI del Panel Frente

HDMI-aansluitingen op de voorzijde

Collegamento delle prese HDMI anteriore

HDMI-anslutning på främre

Подключение к HDMI разъему на передний панели

11

480p/576p/720p/1080i/1080p HDTV/ 4K UHDTV

Blu-ray Player or other digital source with HDMI output

PUSH

ON

OFF

Figure 10: Rear HDMI Connections

Connexions HDMI arrières

Rückseitige HDMI-Verbindungen

Conexiones HDMI del Panel Posterior

HDMI-aansluitingen op de achterkant

Collegamento delle prese HDMI posteriori

HDMI-anslutning på baksidan

Подключение к HDMI разъему на задней панели

12

RSP-1576MKII Surround Sound Processor

INPUT SETUP

SPEAKER CONFIGURATION

SPEAKER DISTANCE SETUP

SUBWOOFER SETUP

SPEAKER LEVEL SETUP

VIDEO SETUP

SYSTEM SETUP

EXIT

AUDIO CONFIGURATION

MAIN MENU

SOURCE

NAME

VIDEO INPUT

AUDIO INPUT

TRIGGER OUTPUT

DEFAULT MODE

AUDIO DELAY

LEVEL ADJUST

BACK

INPUT SETUP

VIDEO 1

HDMI AUDIO

MULTI INPUT

1 _ _

SOURCE DEPENDENT

0M SEC

0DB

DIRAC

DISABLED

FRONT

CENTER

SURROUND

SUBWOOFER

OVERHEAD REAR

ADVANCED SETUP

BACK

CENTER BACK

OVERHEAD FRONT

SPEAKER CONFIGURATION

LARGE

YES

LARGE

2 LARGE

LARGE

SOURCE

NAME

VIDEO INPUT

TRIGGER OUTPUT

LEVEL ADJUST

DIRAC

INPUT SETUP

MULTI INPUT

M-INPUT

HDMI 1

1 _ _

0DB

BACK

DISABLE

SPEAKER

CROSSOVER

DOLBY

DTS

STEREO

BACK

ADVANCED SPEAKER SETUP

FRONT

100 HZ

DEFAULT

FRONT LEFT

CENTER

FRONT RIGHT

SURROUND RIGHT

CENTER BACK RIGHT

CENTER BACK LEFT

SURROUND LEFT

SUBWOOFER

BACK

OVERHEAD FRONT RIGHT

OVERHEAD REAR RIGHT

OVERHEAD REAR LEFT

OVERHEAD FRONT LEFT

SPEAKER LEVEL SETUP

0DB

SOURCE

NAME

VIDEO INPUT

AUDIO INPUT

TRIGGER OUTPUT

DEFAULT MODE

AUDIO DELAY

LEVEL ADJUST

DIRAC

FIXED VOLUME

INPUT SETUP

PC - USB

HDMI 1

USB AUDIO 2.0

1 _ _

SOURCE DEPENDENT

0M SEC

0DB

VARIABLE

BACK

DISABLE

DOLBY

STEREO

MULTI LPCM

MULTI INPUT

BACK

SUBWOOFER SETUP

DTS

0DB

STANDBY VIDEO SOURCE

FAST AUDIO SYNC

VIDEO SETUP

DISABLE

OSD FORMAT

BACK

480P

DISABLE

FRONT

CENTER

SURROUND

SUBWOOFER

CENTER BACK

HEIGHT 1

HEIGHT 2

BACK

CONFIGURATION

AUDIO CONFIGURATION

FRONT

CENTER

SURROUND

SUBWOOFER

CENTER BACK

OVERHEAD F RONT

OVERHEAD REAR

7 . 1 . 4

MAIN SOFTWARE

DSP SOFTWARE

STANDBY SOFTWARE

VFD SOFTWARE

HDMI SOFTWARE

CHECK FOR SOFTWARE UPDATE

BACK

SOFTWARE INFORMATION

V 00 . 00 . 00

CONFIRM RESTORE FACTORY DEFAULTS!

BACK

RESTORE FACTORY DEFAULT

OFF TIMER

BACK

SIGNAL SENSE INPUT

POWER MODE

POWER OPTION

20 MINS

DISABLE

NORMAL

MAX POWER ON VOLUME 45

LANGUAGE

IR REMOTE CODESET

DISPLAY

NETWORK WAKEUP

SOFTWARE INFORMATION

RESTORE FACTORY DEFAULT

BACK

NETWORK CONFIGURATION

SYSTEM SETUP

ENGLISH

CODESET 1

HDMI AND VFD

DISABLE

POWER OPTION

IP ADDRESS MODE

VIEW NETWORK SETTINGS

TEST NETWORK CONNECTION

BACK

NETWORK CONFIGURATION

RENEW DHCP IP ADDRESS

DHCP

FRONT LEFT

CENTER

FRONT RIGHT

SURROUND RIGHT

CENTER BACK RIGHT

CENTER BACK LEFT

SURROUND LEFT

SUBWOOFER

BACK

OVERHEAD FRONT RIGHT

OVERHEAD REAR RIGHT

OVERHEAD REAR LEFT

OVERHEAD FRONT LEFT

SPEAKER DISTANCE SETUP

10.00 FT 3.05M

On-Screen Menus

Afchage des menus à l’écran

On-Screen-Menüs

Sistema de Menús en Pantalla

Schermmenu’s

Menù sul display (OSD)

Menyer

Экранные меню

13

About Rotel

Our story began over 50 years ago. Over the decades, we have received

hundreds of awards for our products and satised hundreds of thousands

of people who take their entertainment seriously- like you!

Rotel was founded by a family whose passionate interest in music led them

to manufacture high-delity components of uncompromising quality. Through

the years, that passion has remained undiminished and the family goal of

providing exceptional value for audiophiles and music lovers, regardless

of their budget, is shared by all Rotel employees.

Rotel’s engineers work as a close team, listening to, and ne tuning, each

new product until it reaches their exacting musical standards. They are

free to choose components from around the world in order to make that

product the best they can. You are likely to nd capacitors from the United

Kingdom and Germany, semiconductors from Japan or the United States,

while toroidal power transformers are manufactured in Rotel’s own factory.

We all have concerns about our environment. And, as more and more

electronics are produced it is especially important for a manufacturer to do all

it can to engineer products that have a minimum impact on the environment.

At Rotel, we are proud to do our part. We have reduced the lead content

in our products by using special lead-free ROHS solder and components.

Our engineers continually strive to improve power supply efciency without

compromise to quality. When in standby mode Rotel products use minimal

power to meet global Standby Power Consumption requirements.

The Rotel factory is also doing their part to help the environment through

constant improvements to product assembly methods for a cleaner and

greener manufacturing processes.

All of us at Rotel thank you for buying this product. We are sure it will bring

you many years of enjoyment.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic,

and the double-D symbol are registered trademarks of Dolby Laboratories.

For DTS patents, see http://patents.dts.com. Manufactured under license

from DTS Licensing Limited. DTS, the Symbol, DTS in combination with the

Symbol, DTS:X, and the DTS:X logo are registered trademarks or trademarks

of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All

Rights Reserved.

Getting Started

Thank you for purchasing the Rotel RSP-1576MKII Surround Sound Processor.

The unit is a full-featured audio/video control center for analog and digital

source components. It features digital processing for a wide range of formats

including Dolby

®

Surround, Dolby

®

ATMOS and DTS

®

source material.

Video Features.

• HDMI switching for digital video signals up to 4K.

• Accepts HDMI video input: 480i, 480p/576p, 720p, 1080i, 1080p,

1080p 24Hz, 4K.

• Outputs HDMI video (480i, 480p/576p, 720p, 1080i, 1080p, 1080p

24Hz, 4K) compatible with common HDMI displays and projectors.

Audio Features

• Rotel’s Balanced Design Concept combines advanced circuit board

layout, comprehensive parts evaluation, and extensive listening tests

for superior sound and reliability.

• Analog bypass mode for pure 2 channel stereo with no digital processing.

• Digital and analog inputs including Coax, Optical, RCA and Balanced

XLR.

• 7.1 Multi-Channel input from compatible source components.

Surround Features

• Automatic Dolby

®

and DTS surround decoding of all popular formats

up to 7.1.4 channels.

• Surround modes for playback of multi channel audio on 2 channel

and 3 channel systems.

• Audio Return Channel (ARC) allowing the audio from the TV to be

processed by the RSP-1576MKII via HDMI.

Other Features

• User friendly ON-SCREEN DISPLAY (OSD) menu system with

programmable labels for all inputs.

• Multi language support in OSD setup.

• Upgradable software to accommodate future updates through the rear

Internet connection or front USB port.

• Assignable 12V trigger outputs for remote turn-on of power amplier(s)

and other components.

Unpacking

Remove the unit carefully from its packaging. Find the remote control and

other accessories. Save the box as it will protect the product if you move

or need to return it for maintenance.

Placement

Place the unit on a solid, level surface away from sunlight, heat, moisture,

or vibration. Make sure that the shelf can support the weight of the unit.

14

RSP-1576MKII Surround Sound Processor

Place the unit close to the other components in your system and, if possible,

on its own shelf or with the optionally included rack ears. This will make

initial connection, and subsequent system changes easier.

The unit can generate heat during normal operation. Do not block ventilation

openings. Allow a minimum of 10 cm or 4 inches of unobstructed space

around the unit. If installed in a cabinet, make sure that there is adequate

ventilation.

Do not stack other components or objects on top of the unit. Do not let any

liquid fall into the cabinet.

Overview of Connections

NOTE: Do NOT plug any system component into an AC source until

all connections have been properly made.

Source components within the system can be connected to the unit’s inputs

with either a pair of standard RCA cables or balanced XLR cables for analog

audio, or digitally, via HDMI, coax or optical.

Outputs of the RSP-1576MKII are sent to the power amplier(s) with standard

RCA cables from the preamp audio outputs. The video signal from the

RSP-1576MKII is sent to the monitor using the HDMI connections.

In addition, the processor has MULTI INPUT connections for use with a

source component that does its own surround decoding, remote IR receiver

inputs, 12V trigger outputs.

NOTE: The S/PDIF digital audio interface standard specifies a 75

ohm impedance and all good digital cables adhere to this requirement.

Do NOT substitute conventional audio interconnect cables for digital

signals. Standard audio interconnects will pass these signals, but their

limited bandwidth reduce performance.

When using analog audio connections ensure the Left and Right signals are

attached to the proper RCA jacks. All RCA-type connections on this product

follow these standard color codes:

Left channel audio: white RCA jack

Right channel audio: red RCA jack

NOTE: Each source input must be properly configured using the INPUT

SETUP menu of the OSD menu system. We recommend going to this

menu after connecting each source to configure it as desired. See Input

Setup in the Setup section for more information.

HDMI Inputs and Outputs

These connections are used for connecting video signals to and from the

unit. See the Making Connections section for speciﬁc instructions for each

type of component on page 16.

Rear HDMI IN 1–6 Video Inputs r

HDMI inputs provide digital video connections for use with components that

have HDMI outputs. HDMI connections carry video signals in multiple formats

including 3D, 1080p/24Hz, and 4K. The implementation of HDMI supports

audio signals, or a separate audio connection from an HDMI component.

All HDMI inputs support 4K UHD HDCP 2.2 as labeled on the rear panel.

Front HDMI IN 6

The Video 7 input is located on the front panel for easier access. Use

this HDMI connection for portable sources or devices that would not be

permanently connected.

HDMI Monitor Outputs e

The two HDMI outputs of the RSP-1576MKII can send High Denition video

signals to two display devices in parallel. The HDMI outputs can send video

signals to a high-deﬁnition TV 2D (480p/576p, 720p, 1080i, 1080p or

4K) and 3D (up to 1080p/24Hz). Both HDMI output will support 4K UHD

HDCP 2.2 as labeled on the rear panel.

There are two HDMI outputs on the rear panel sending out the same video

signal. Only one of the two will send the On Screen Menu to your TV.

Of the two HDMI Outputs, only one HDMI output supports ARC (Audio

Return Channel) and is labeled “ARC/OSD” above the HDMI connector.

Please refer to the INPUT SETUP menu section of this manual for more

details on page 21.

Your TV may have more than one HDMI input. Not all HDMI inputs support

ARC. Please use the ARC enabled HDMI input of your TV to use the ARC

function on this product. ARC compatible inputs should be labeled with

“ARC” next to the HDMI input connector.

Additional information for HDMI video outputs:

• All HDMI attached devices must be HDCP compatible to ensure proper

display of the HDMI video signal.

• Audio received over HDMI will be processed by this product and sent

out via the RCA terminal outputs.

• When using both HDMI outputs simultaneously, both HDMI outputs

will be set to the same resolution. This resolution will be the lower

resolution of any attached monitor.

Audio Inputs and Outputs

This Rotel processor provides both analog and digital audio connections.

PHONO Input f

A Left/Right pair of RCA analog audio inputs for connecting a phono player

with a moving magnet cartridge. If the turntable has a “ground” wire, connect

it to the screw terminal labeled “GND” to the left of the Digital inputs.

TUNER Input f

A Left/Right pair of RCA analog audio inputs for connecting a tuner.

CD Input f

A Left/Right pair of RCA analog audio inputs for connecting a CD player.

By default the CD source is set to CD analog RCA input, but this can be

changed to XLR, Coax 1-3 or Optical 1-3 in the input setup menu.

AUX Input f

A Left/Right pair of RCA analog audio inputs for connecting a audio

playback device with an analog audio output.

15

BALANCED Input d

A Left/Right pair of Balanced XLR audio inputs for connecting a source

component with Balanced XLR audio outputs.

MULTI Input g

A set of RCA inputs accepting up to 7.1 channels of analog signals from a

source component capable of decoding multi channel audio. These inputs

support FRONT L & R, CENTER, SUB, REAR L & R, and CENTER BACK

L[1] & R[2].

These inputs bypass all digital processing in the RSP-1576MKII and are

routed directly to the volume control and outputs.

PREAMP Output h

A group of fourteen RCA analog audio outputs sends the RSP-1576MKII’s

line level output signals to external ampliers and powered subwoofers.

These output levels are variable and adjusted by the RSP-1576MKII’s volume

control. The fourteen connectors provide output for: FRONT L & R, REAR

L & R, CENTER BACK L[1] & R[2], CENTER 1 & 2, SUBWOOFER 1 & 2,

HEIGHT 1 L & R and HEIGHT 2 L & R.

DIGITAL Inputs w

The RSP-1576MKII accepts digital inputs from source components such as CD

players, satellite TV tuners, and DVD players. The DSP in the RSP-1576MKII

detects the sampling rate of the incoming signal and automatically adjusts.

Sampling rates up to 192kHz are supported.

NOTE: Digital inputs support both 2 Channel Stereo and Multi Channel

audio signals. When using the digital input with a Multi Channel

audio signal the processor DSP will decode the incoming audio stream

including Dolby or DTS.

There are six digital audio inputs on the rear panel, three coaxial and

three optical. These digital inputs can be assigned to any of the VIDEO

1 - 7 input sources using the INPUT SETUP menu during the setup process.

For example, you can assign the COAXIAL 1 digital input connector to the

VIDEO 1 source and the OPTICAL 2 digital input to the VIDEO 3 source. By

default, the source of the audio for inputs Video 1 - 7 is set to HDMI Audio.

By default the CD source is set to CD analog RCA input, but this can be

changed to XLR, Coax 1-3 or Optical 1-3 in the input setup menu.

PC-USB Input t

See Figure 4

Connect this input using the supplied USB cable to the USB socket of your

computer.

The RSP-1576MKII supports both USB Audio Class 1.0 and USB Audio

Class 2.0 modes. Windows computers do not require installation of a

driver for USB Audio Class 1.0 and support playback of audio up to 96kHz

sampling rates.

The Factory Default setting is USB Audio Class 2.0. To take advantage of

USB Audio Class 2.0 audio playback supporting up to 192kHz sampling

rates you will need to install the Windows driver supplied on the CD included

with the RSP-1576MKII.

You can switch the RSP-1576MKII to USB Audio Class 1.0 playback mode

with the following:

• Press SETUP on the remote control to enter MAIN MENU and use

Up/Down buttons to select the INPUT SETUP menu then press ENTER.

• Use Left/Right buttons to select “PC-USB” as INPUT SOURCE and select

“USB Audio 1.0” as AUDIO INPUT.

• Power cycle the RSP-1576MKII and reboot your PC after changing

the USB Audio mode to ensure both units are properly congured.

Many audio playback applications do not support 192kHz sampling rate.

Please conrm your audio player supports 192kHz audio and you have

192kHz audio les to properly playback this sample rate. Also, you may

need to congure the audio driver in your PC to output 192kHz or your

computer may “down sample” to a lower audio sample rate. For more

information please refer to your audio player or operating system information.

NOTE: Upon successful installation of the driver, you may need to select

the ROTEL audio driver from the audio/speaker setup of your computer.

Front USB Input 5

See Figure 6

This connection will accept Apple devices such as iPod, iPad and iPhone.

While connected, the iPod and iPhone displays remain active allowing

search and play functions.

Other Connections

AC Input j

Your Rotel processor is conﬁgured at the factory for the proper AC line

voltage in the country where you purchased it (USA: 120 volts/60 Hz

AC or CE: 230 volts/50 Hz AC). The AC line conﬁguration is noted on a

decal on the back of your unit. Plug the supplied cord into the AC INPUT

receptacle on the back of the unit.

Master Power Switch a

The large rocker switch on the rear panel is a master power switch. When

it is in the OFF position, power to the unit is completely off. When it is in

the ON position, the front panel STANDBY and remote control ON/OFF

buttons can be used to activate the unit or put it into standby mode.

12V TRIGGER Output i

Many Rotel ampliers offer the option of turning them on and off using a

12 volt trigger. These three connections provide this 12 volt trigger signal

from the processor. When the unit is activated, a 12 volt DC signal is sent

from these jacks to the ampliers to automatically turn them on. When the

processor is put in STANDBY mode, the trigger signal is removed and the

ampliers automatically turn off.

To use the automatic trigger turn on feature, connect one of the RSP-

1576MKII’s 12V TRIG OUT jacks to the 12 volt trigger input of a Rotel

amplier, using only the black 3.5 mm trigger cable included with this unit

or a Rotel amplier. Do not use any other cable for trigger connection. The

+12V DC signal appears at the “tip” of the connector.

The 12V Trigger outputs are conﬁgured to turn on in various combinations

only when speciﬁc input sources are activated. See the INPUT SETUP menus

in the Setup section of this manual for details on page 21.

16

RSP-1576MKII Surround Sound Processor

REM IN Jack o

This 3.5 mm mini-jack receives command codes from third-party IR remote

receiver. These remote IR inputs can be used when the RSP-1576MKII front

IR receiver cannot be reached by a sending remote control.

Consult your authorized Rotel dealer for more information on the REM IN jack.

The IR signals from the REM IN jack can be relayed to other source components

using external IR emitters or hard-wired connections from the IR OUT jacks.

See the following section for additional information.

IR OUT Jacks p

The IR OUT 1 & 2 jacks send IR signals received at the REM IN jack to

an infrared blaster or emitter placed in front of a source component’s IR

sensor. In addition, the IR OUT can be hard-wired to other Rotel products

with a REM IN jack.

These outputs allow IR signals to be “relayed” through the RSP-1576MKII

either directly to the IR receiver on the front panel or via the REM IN jack

on the rear panel. This function provides easy control of other source

components when their IR inputs are not accessible such as when they are

installed in a rack system or in a cabinet.

See your authorized Rotel dealer for more information on IR emitters and

repeater systems.

Rotel Link [

Rotel Link is not used for RSP-1576MKII.

Rear USB Power Port \

The rear USB port provides 5V for charging or powering USB devices

including streaming music players. This port does not allow playback of audio.

The port can be congured to remain powered even when the RSP-1576MKII

is in standby mode through the front panel setup menu (See the Power Mode

under the Power Option menu on page 26).

The Power Mode “Quick” option allows the attached streaming source to

remain powered for use with the Signal Sense function for automatic power

on/off control of the RSP-1576MKII.

NOTE: When configured to provide continuous power to the rear panel

USB port the RSP-1576MKII will consume additional power even when

in standby mode.

RS232 Connector y

The RSP-1576MKII can be controlled via RS232 for integration with

automation systems. The RS232 connector accepts a standard straight DB-9

Male-to-Female cable.

NETWORK Connector u

The Network socket accepts standard RJ-45, CAT-5 cables. The network

connection is not required for normal operation of this unit. This connection

is for software updates or control from an automation system only.

For additional information on the connections, cabling, software, and

operating codes for automation system control or software updates, contact

your authorized Rotel dealer.

Making Connections

Connecting an External Amplier

See Figure 3

The RSP-1576MKII has preamp RCA outputs for connections to external

power ampliers to drive up to 12 speakers in congurations from 5.1 to

7.1.4. In addition, there are two subwoofer outputs.

To connect ampliers, connect an audio cable from each output jack to the

input of the amplier channel that will power the corresponding speaker.

For example, connect the FRONT L output to the amplier channel driving

the front left speaker. There are two CENTER RCA jacks; use either jack for

a single center channel, or both if you have two center channels. In six or

seven channel systems, make one or two additional connections for Center

Back channel(s). These jacks are labeled CB L[1] and CB R[2]. Use CB L[1]

for a single center back channel. Ceiling or Overhead speakers should be

connected to the Height 1 and Height 2 jacks.

For preamp output connection information see Audio Conguration options

in the RSP-1576MKII Setup Menu on page 22.

After you have connected the preamp outputs, you need to conﬁgure the

RSP-1576MKII for the size and style of speakers in your system and calibrate

the relative volume levels of the speakers. See the Speaker Level Setup

section of this manual on page 24.

Connecting a Subwoofer

See Figure 3

To connect a powered subwoofer, connect a standard RCA audio cable

from the jacks labeled SUB 1/SUB 2 to the input on the subwoofer’s power

amp. Both SUB outputs provide the same signal. Use either connection

for a single subwoofer. Use both connections to connect two subwoofers.

After you have connected the subwoofer, you need to conﬁgure the unit to

use the subwoofer and calibrate the relative volume level of the subwoofer.

See the Speaker Level Setup section of this manual on page 24.

Connecting a DVD, Blu-ray, Cable, Satellite, Game Console and HDTV Tuner

See Figure 5 and 9

Source devices including Blu-ray, DVD, satellite, cable, etc. should be attached

to the RSP-1576MKII using HDMI. Connect an HDMI cable from the output

of the source to one of the HDMI inputs on the processor.

Digital audio connection: Depending on the setup of your system, you can also

use the audio digital connections and assign them to the HDMI video inputs.

Connect the digital output of the source to any of the DIGITAL IN OPTICAL

1–3 or DIGITAL IN COAXIAL 1–3 inputs on the processor. An HDMI cable

carries both digital video and digital audio signals; therefore, in most cases

no separate digital audio connection needs to be made.

Use the INPUT SETUP screen to assign the audio digital input to the HDMI

video input source used above.

17

Although there are typically no video connections for a CD Player, the

RSP-1576MKII can assign another video input to the CD or XLR input. The

Video choices are HDMI 1-7 (Front), Last Video Source, or Off. HDMI 1

video input is assigned to CD and XLR as the default setting.

Connecting a Tuner

See Figure 8

Digital audio connection: If using an HD Radio or other digital tuner, connect

the digital output of the tuner to the Optical or Coax digital inputs on the

RSP-1576MKII. Use the INPUT SETUP menu to assign the audio input to the

TUNER source (the default is TUNER analog input jacks).

Analog audio connection:

Option 1: If using an analog tuner, connect the left and right analog outputs

from the tuner to the pair of analog input jacks labeled TUNER on the

RSP-1576MKII. Make sure that you connect the right channel to the R input

jack and the left channel to the L input jack.

Option 2: If your Tuner has XLR output connectors, you can use the XLR inputs

on the RSP-1576MKII for this connection. Connect the left and right XLR

outputs from the source to the jacks labeled BALANCED INPUT (left and right).

Although there are typically no video connections for a Tuner, the

RSP-1576MKII can assign another video input to the Tuner input. The Video

choices are HDMI 1 - 7 (Front), Last Video Source, or Off. HDMI 1 video

input is assigned to the Tuner input as a default setting.

Connecting an iPod/iPhone

See Figure 6

Connect the iPod/iPhone to the front USB socket.

NOTE: The audio inputs CD, PHONO, XLR, MULTI, USB, PC-USB,

BLUETOOTH, and TUNER are set to HDMI 1 video input as the factory

default. Video input can be changed to HDMI 1-7 (Front), Last Video

Source, or Off.

Front Panel Overview

The following is a brief overview of the controls and features on the front

panel of the unit. Details concerning the use of these controls are provided

in subsequent sections of this manual describing various tasks.

Front Panel Display 3

The Display on the front panel shows the volume, DSP mode, source selected

and type of audio mode the unit is receiving or processing.

IR Remote Sensor 2

This sensor receives IR signals from the remote control. Do not block this sensor.

NOTE: The remainder of the buttons and controls on the front panel

are described in the Overview of Buttons and Controls section.

Connecting a Blu-ray or DVD Player

See Figure 5

In some cases DVD, SACD, and other external multichannel processors are

connected to the processor by sending decoded analog audio signals using

RCA cables. A player with HDMI outputs can send digital signals directly

to the processor for decoding.

Analog Connections: To connect a Blu-ray or DVD player (or any device

that decodes multi-channel audio) with analog connections, use audio RCA

cables to connect the outputs of the player to the RCA jacks labeled MULTI

INPUT on the RSP-1576MKII. Make sure that you observe proper channel

consistency, i.e. connect the right front channel to the FRONT R input, etc.

Depending on your system conﬁguration, make six connections (FRONT L

& R, REAR L & R, CENTER, and SUBWOOFER), seven connections (adding

a CENTER BACK connection), or eight connections (adding two CENTER

BACK connections).

The MULTI inputs are analog bypass inputs, passing signals directly to the

Volume Control and preamp outputs, bypassing all of the digital processing.

HDMI digital connection: If the player has HDMI outputs, simply connect

an HDMI cable from the output of the player to one of the HDMI inputs

on the processor. This cable sends the video signal from the player along

with a digital audio signal. Using HDMI for audio and video allows the

multichannel decoding to be handled by the processor.

Connecting a Display

See Figure 10

Connect one of the HDMI outputs of the RSP-1576MKII to the HDMI input

of your TV or projector. The RSP-1576MKII has two HDMI outputs. Only

one HDMI output will display the OSD and is ARC enabled. This output is

labeled on the rear panel with ARC/OSD.

Connecting a CD Player or XLR Source

See Figure 7

Digital audio connection: Connect the digital output of the CD player to the

Optical or Coax digital inputs on the RSP-1576MKII. Use the INPUT SETUP

menu to assign the audio input to the CD (the default is CD).

Analogue audio connections:

Option 1: Connect the left and right analog outputs from the CD player to

the AUDIO IN jacks labeled CD (left and right). This option uses the CD

player’s D/A converter. Depending on the selected DSP mode this connection

method may require the analog signal to be converted to a digital signal

for processing.

Option 2: If your CD Player (or another source) has XLR output connectors,

you can use the XLR inputs on the RSP-1576MKII for this connection.

Connect the left and right XLR outputs from the source to the jacks labeled

BALANCED INPUT (left and right). This option uses the CD player’s D/A

converter. Depending on the selected DSP mode this connection method may

require the analog signal to be converted to a digital signal for processing.

18

RSP-1576MKII Surround Sound Processor

Input Buttons 4qM

The input source can be changed by pressing the desired source input

buttons on the front panel or remote control.

SUR+ Buttons 9B

The SUR+ buttons on the remote control or front panel will display surround

mode information of currently selected source. The default DSP mode can

be congured in the Setup menu for each source. Press the SUR+ button

repeatedly to toggle through the available DSP modes.

DSP processing options vary depending on the selected source input type.

Not all DSP options are available in analog or digital input modes.

Other buttons on the remote can directly access specic DSP modes.

2CH: Changes the audio mode to STEREO, DOWN MIX.

BYPASS: Bypass all DSP processing.

PLCM: Selects Dolby ATMOS surround mode.

Playback Control buttons L

These buttons provide basic control functions for iPod AUDIO playback.

The control buttons can also control Rotel CD players. For more information

how to congure CD controls see the REMOTE CONTROL OVERVIEW

section of the manual. Supported functions include Play, Stop, Pause, Next

Track, Previous Track.

DIM Button J

Use this button to dim the front panel display.

Adjustment made using the

J

button is temporary only and not saved

after power off.

SUB, CTR, REAR Buttons B

These buttons can access the speaker setting and adjust the output level for

speakers in the system. Use the Up and Down arrow buttons on the remote

control to change values. This is only a temporary change. To make permanent

adjustments, please access the SPEAKER LEVEL SETUP menu from the OSD.

MEM Button E

This button does not operate with the RSP-1576MKII and is used only to

control a Rotel tuner product for preset memory control.

LIGHT Button N

Pushing this button turns on the back light of the remote control for easy

operation in dimly lit rooms.

ASSISTIVE LIGHT O

Push and hold on the LIGHT Button

N

for 3 seconds to turn on the assistive

light. This light can be used to help locate objects in a dimly lit room such

as a home theatre surrounding. The light will remain illuminated as long

as the button is held.

Automatic Surround Modes

Decoding of digital sources connected is generally automatic with detection

triggered by a “ﬂag” embedded in the digital recording telling the processor

what decoding format to use. For example, when a Dolby or DTS surround

signal is detected, the processor activates the proper decoding.

Remote Control Overview

The RSP-1576MKII is supplied with an easy to use remote control RR-CX100.

The RR-CX100 can be congured to use IR codeset 1 or IR codeset 2 in case

the unit is conicting with other Rotel models. Push and hold the TUNER

button and 1 (or TUNER and 2 for codeset 2) at the same time and hold for

approximately 5 seconds until the backlights on the remote control blink on

then off then release both buttons. This sets the remote control to use codeset

1 (or codeset 2 if TUNER and 2 are held). The System menu in the OSD

includes a conguration option to set the processor to either codeset 1 or

codeset 2. The factory default for the remote and processor is codeset 1.

The RR-CX100 can also control an attached Rotel CD player. The CD player

functions include Play, Stop, Pause, Track Forward, Track Back, Fast Forward,

Fast Reverse. To activate these functions press the CD button on the remote.

If the CD is attached to the XLR source input, these functions can be activated

by pressing the XLR button. To change the CD player functions to operate

after pressing the XLR button press and hold the XLR and 1 button for 5

seconds until the backlight LEDs blink twice times then release. To disable

XLR sending the CD control functions press and hold the XLR and 0 button

for 5 seconds until the backlight blinks.

The transport buttons will only operate for CD control after the CD or XLR

button is pressed on the remote. If a different input is selected from the

remote these buttons will no longer send the CD transport IR commands.

Overview of Buttons and Controls

This section provides a basic overview of the buttons and controls on the

front panel and the remote control. Detailed instructions on the use of these

buttons are provided in the more complete operating instructions in the

following sections.

STANDBY 1 and Power ON/OFF Buttons A

The front-panel STANDBY button and the remote control ON/OFF button

activate or deactivate the unit. The rear panel master POWER switch must

be on the ON position for the remote standby function to operate.

VOLUME Knob and VOLUME UP/DOWN Buttons =D

The VOLUME UP/DOWN buttons on the remote and the large rotary control

on the front panel provide the master VOLUME control, adjusting the output

level of all channels simultaneously including mute and volume level 1 to 96.

DISPLAY (DISP) Button 0B

Push this button to toggle through device status on the VFD and TV.

SETUP Button H

Navigating and ENTER Buttons I

The SETUP button displays the OSD setup screen on the HDMI OSD enabled

output. Push the SETUP button again to deactivate this menu. Use the

navigation buttons Up/Down/Left/Right and ENTER on the remote control

to access the various menus.

MUTE Button -F

Push the MUTE button once to turn the sound off. An indication appears in

the front panel and on-screen display. Press the button again to restore the

previous volume level.

19

The processor will recognize a digital signal with Dolby Surround encoding

and activate Dolby

®

decoding. Additionally, you can conﬁgure a default

surround mode for each input using the INPUT SETUP menu (see the Setup

section of this manual). Combined with the auto-detection of Dolby Digital

and DTS, this default surround setting makes operation of the processor’s

surround modes totally automatic.

For stereo inputs such as CD and Tuner, you could select BYPASS or STEREO

mode as the default for 2-channel playback or a DSP mode if you prefer to

hear music sources in surround sound.

NOTE: A digital signal coming into the processor will be recognized and

properly decoded. However, on a Blu-ray with multiple soundtracks, you

may need to configure the player for the desired signal and encoding type.

For example, you may need to use the player’s menu system to select the

desired Dolby Digital or DTS soundtrack.

Manually Selecting Surround Modes

For users who prefer a more active role in setting surround modes, buttons

on the remote and the front panel provide manual selection of surround

modes that are not automatically detected or, in some cases, to override

an automatic setting.

Manual settings available from the front panel and/or the remote control

should be used when you want to play:

• Standard 2-channel stereo (Left/Right speakers, and depending upon

speaker settings also subwoofer) with no surround processing.

• Down mixed 2-channel playback of Dolby Digital 5.1 or DTS recordings.

• Dolby 3-channel stereo (Left/Right/center) of 2-channel recordings.

• 5-channel stereo, 7-channel, 9-channel or 11-channel from 2-channel

recordings.

• Other modes may be available depending on the system conguration

and active source material.

• PCM 2-channel (non 96kHz) digital signals can be overridden to Dolby

3-Stereo, 5CH Stereo, 7CH Stereo, 9CH, and 11CH and Stereo as

well as Dolby Atmos and DTS Neural:x.

To change the surround mode press the SUR+ button on the remote control

or front panel to toggle through the available options. The 2CH button on

the remote control will create a down mix of any multichannel signal to 2

channel stereo mode.

NOTE: Not all surround modes are available for all surround source

formats. The input source signal will determine the available surround

options that can be selected.

Digital Audio

You can play these recordings in BYPASS, 2-CH Stereo, Dolby 3-Stereo, 5-CH

Stereo, 7-CH Stereo, 9CH Stereo, 11CH Stereo, Dolby ATMOS Surround

and Dolby Neural:X modes.

All of the bass management settings (speaker size, subwoofer, and crossover)

are in effect with digital stereo inputs unless BYPASS mode is selected.

To change the surround mode press the SUR+ button on the remote control

or front panel control to toggle through the available surround options. The

2CH button on the remote control will create a down mix of any multichannel

signal to 2 channel stereo mode.

NOTE: Not all surround modes are available for all surround source

formats. The input source signal will determine the available surround

options that can be selected.

Analog Stereo

This type of recording includes any conventional stereo signals from the

processor’s analog inputs, including analog audio from CD players, FM

tuners, etc.

Analog stereo inputs require a choice about how the signal is routed through

the processor. One option is the ANALOG BYPASS mode. In this mode, the

stereo signal is routed directly to the volume control and the outputs. This

mode is pure 2-channel stereo, bypassing all of the digital circuitry. None

of the bass management features, speaker level settings, EQ settings, Dirac

lters, or delay settings is active. There is no subwoofer output. A full-range

signal is sent directly to the front left and right speakers.

Alternatively, a DSP mode can be enabled, this converts the analog

inputs to digital signals, passing them through the digital processors in the

RSP-1576MKII. This option allows all of the features to be active including

bass management settings, crossovers, subwoofer outputs, EQ settings,

etc. There are several DSP modes available including: 2-CH Stereo, Dolby

3-Stereo, 5-CH Stereo, 7-CH Stereo, 9CH and 11CH Stereo, Dolby ATMOS

Surround and Dolby Neural:X modes.

To change the surround mode press the SUR+ button on the remote control

or front panel control to toggle through the available surround options.

NOTE: Not all surround modes are available for all surround source

formats. The input source signal will determine the available surround

options that can be selected.

Basic Operation

This section covers the basic operating controls of the RSP-1576MKII and

the remote control.

Selecting Inputs

You can select any of the source inputs for listening and/or watching: VIDEO

1 - 7, CD, PHONO, XLR, MULTI INPUT, USB, PC-USB, BLUETOOTH or TUNER.

The source inputs can be customized using the INPUT SETUP menu to assign

which HDMI input to use as the video source. Video 1- 7 inputs can also

be congured to accept any analog and digital audio sources. The default

of audio source is set to HDMI Audio.

When you have congured the source input, you can use Input buttons to

select the desired inputs:

1. Press the Input buttons on the front panel 4q to switch to the selected

source input i.e. CD, Tuner, Video 1 etc...

2. Press the source input button on the remote control M to select the

desired source.

20

RSP-1576MKII Surround Sound Processor

USB/iPod Operation

iPod/iPhone Connection 5

1. An iPod/iPhone can be connected using the proper USB cable to the

USB front socket of the RSP-1576MKII.

2. The iPod/iPhone will stream a digital music signal to the unit. Music

selection and playback control are available using the iPod/iPhone.

3. The iPod/iPhone screen will remain active while connected to the unit.

Playback Control Buttons L

Transport controls are available from the remote control during playback

including play, stop/pause, next track, previous track.

Bluetooth

Bluetooth Connection

The Bluetooth feature allows you to stream music wireless from your Bluetooth

enabled device, i.e. mobile phones. Select the BLUETOOTH (BT) input on

the RSP-1576MKII. From your device (mobile phones etc.) activate Bluetooth

and allow it to search for other Bluetooth devices. Select “Rotel Bluetooth”

and connect to it. Once connected you can start streaming music to the

RSP-1576MKII.

NOTE: The RSP-1576MKII Bluetooth is APTX compatible. This enables

you to stream music at lossless CD quality.

NOTE: Some Bluetooth devices may require you to establish connection

again with the RSP-1576MKII if the unit was powered off. If this occurs,

please go through the above steps to re-connect.

Rear PC-USB

Rear PC-USB Connection

The rear USB socket labeled PC-USB accepts a type B USB plug. This input

accepts PCM audio signals sent from your computer up to 24 bits/192kHz

resolution.

Setup

The Rotel RSP-1576MKII features two types of information displays to help

operate the system. The ﬁrst consists of simple status displays that appear on

the TV screen whenever primary settings (Volume, Input, etc.) are changed.

A more comprehensive ON-SCREEN DISPLAY (OSD) menu system is available

at any time by pressing the SETUP H button on the remote. These OSD

menus guide you through the conﬁguration and setup of the RSP-1576MKII.

The settings made in the conﬁguration process are memorized as default

settings and need not be made again for normal operation of the unit.

The OSD menus can be conﬁgured to display several different languages.

The default English version of all main menus are shown at the front of this

manual. If your language is available, those menus will be shown in the

instructions. If you would like to change from the default English language

before proceeding, go to the instructions for the SYSTEM SETUP menu later

in this manual. From this menu, you can change the language display.

Menu Basics

Navigation Buttons

The following remote control buttons are used to navigate the OSD menu

system:

SETUP button: Press to display the MAIN MENU. If a menu is already

visible, push this button to close the OSD and return to normal operation.

Up/Down buttons: Press to move up and down in the lists of menu items

that appear on the OSD screens.

Left/Right buttons: Press to change the current settings for a selected menu

item on OSD screens.

ENTER button: Press ENTER to conﬁrm a setting.

BACK Button: Press BACK to go back to the previous menu.

Main Menu

INPUT SETUP

SPEAKER CONFIGURATION

SPEAKER DISTANCE SETUP

SUBWOOFER SETUP

SPEAKER LEVEL SETUP

VIDEO SETUP

SYSTEM SETUP

EXIT

AUDIO CONFIGURATION

MAIN MENU

The MAIN MENU provides access to OSD screens for various conﬁguration

options. MAIN MENU is reached by pressing the SETUP H button on the

remote. To select the desired menu, move the highlight using the Up/Down

arrow buttons and press the ENTER button on the remote control. Press the

SETUP button again or select “EXIT“ on the OSD to end setup and return

to normal operation.

Conﬁguring Inputs

A key step in setting up the unit, is to conﬁgure each source input using the

INPUT SETUP screens. Conﬁguring the inputs allows you to set defaults for a

number of settings including the type of input connector, the desired surround

mode, custom labels that appear in the displays when a source is selected,

and many more. The following OSD menus are used to conﬁgure the inputs.

La page charge ...

Rotel RSP-1576MKII Le manuel du propriétaire

Rotel RSP-1576MKII Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents