Wacker Neuson RD12-90 Manuel utilisateur

5200003907 01 1111

Operator’s Manual

Roller

RD 12

Notice d’Emploi

Rouleau

EN/FR

5200003907

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5200003906 01 1111

Foreword

wc_tx001937gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Machine Item Number

RD 12 0620059

0620321

Foreword

4 wc_tx001937gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

wc_bo5200003906_01TOC.fm 5

Table of ContentsRD 12

Foreword 3

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Operator Safety while Using Internal Combustion Engines ............... 13

1.5 Service Safety .................................................................................... 14

2 Labels 17

2.1 Label Locations .................................................................................. 17

2.2 Label Meanings .................................................................................. 18

3 Lifting and Transporting 23

3.1 Lifting the Machine ............................................................................. 23

3.2 Tying Down and Transporting the Machine ........................................ 24

4 Operation 25

4.1 Features and Controls ........................................................................ 25

4.2 Control Panel ...................................................................................... 27

4.3 Panel Indicator Lights ......................................................................... 28

4.4 Preparing the Machine for First Use ................................................... 29

4.5 Position of the Operator ..................................................................... 29

4.6 Recommended Fuel ........................................................................... 30

4.7 Refueling the Machine ........................................................................ 31

4.8 Roll Over Protection Structure (ROPS) .............................................. 32

4.9 Foldable Roll Over Protection Structure (ROPS) ............................... 33

4.10 Rotating Beacon (if equipped) ............................................................ 34

4.11 Backup Alarm (if equipped) ................................................................ 34

4.12 Lighting Equipment (if equipped) ........................................................ 35

4.13 Seat Belt ............................................................................................. 35

4.14 Operator Presence System ................................................................ 36

6 wc_bo5200003906_01TOC.fm

Table of Contents RD 12

4.15 Scraper Bars .......................................................................................37

4.16 Anti-Vandalism Protection and Machine Access .................................37

4.17 Articulation Joint Lockarm ...................................................................38

4.18 Machine Stability .................................................................................39

4.19 Operation on Slopes ............................................................................40

4.20 Before Starting ....................................................................................41

4.21 Starting the Machine ...........................................................................41

4.22 Stopping/Parking .................................................................................43

4.23 Emergency Shutdown Procedure ........................................................44

4.24 Parking Brake ......................................................................................45

4.25 Parking Brake Adjustment ...................................................................46

4.26 Direction and Speed ............................................................................47

4.27 Transmission .......................................................................................47

4.28 Vibration ..............................................................................................48

4.29 Water Spray System ...........................................................................49

4.30 Auxiliary Battery Positive Terminal ......................................................50

4.31 Adding Ballast to Rear Drum ...............................................................51

5 Maintenance 53

5.1 Maintaining the Emission Control System ...........................................53

5.2 Engine Maintenance ............................................................................53

5.3 Roller Maintenance Schedule .............................................................54

5.4 Rear Frame Access .............................................................................55

5.5 Battery .................................................................................................56

5.6 Fuel Filter ............................................................................................58

5.7 Cleaning the Water Filter .....................................................................58

5.8 Engine Oil and Filter ............................................................................60

5.9 Spark Plug ...........................................................................................61

5.10 Maintaining the Air Cleaner .................................................................62

5.11 Grease Fittings ....................................................................................63

5.12 Hydraulic System Cleanliness .............................................................64

5.13 Hydraulic Oil Requirements .................................................................65

5.14 Hydraulic Oil Level ..............................................................................65

5.15 Hydraulic Suction Strainer ...................................................................66

5.16 Changing the Hydraulic Oil & Filter .....................................................66

5.17 Bleeding the Hydraulic System ...........................................................67

5.18 Storage ................................................................................................68

5.19 Towing Bypass Valve ..........................................................................69

5.20 Towing .................................................................................................70

5.21 Troubleshooting ...................................................................................72

wc_bo5200003906_01TOC.fm 7

Table of ContentsRD 12

6 Technical Data 73

6.1 Engine ................................................................................................ 73

6.2 Roller .................................................................................................. 74

6.3 Lubrication .......................................................................................... 74

6.4 Dimensions ......................................................................................... 75

6.5 Hydraulic Pressures ........................................................................... 75

6.6 Sound Measurements ........................................................................ 76

6.7 Measurements of Operator Exposure to Vibration ............................. 76

7 Emission Control Systems Information and Warranty 77

7.1 Emission Control System Background Information ............................ 77

7.2 Limited Defect Warranty for Exhaust Emission Control System ......... 78

7.3 Limited Defect Warranty for Wacker Neuson Evaporative

Emission Control Systems ................................................................. 79

8 AEM Safety Manual 83

9 Schematics 110

9.1 Hydraulic Schematic ......................................................................... 110

9.2 Hydraulic Schematic Components ................................................... 111

9.3 Electrical Schematic ......................................................................... 112

9.4 Electrical Schematic Components .................................................... 113

8 wc_bo5200003906_01TOC.fm

Table of Contents RD 12

RD 12 Safety Information

wc_si000516gb.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information RD 12

10 wc_si000516gb.fm

1.2 Machine Description and Intended Use

This machine is a dual drum, ride-on roller. The Wacker Neuson Ride-

On Roller consists of an articulated frame onto which is mounted a

gasoline or diesel engine, a fuel tank, a hydraulic tank, a water tank, a

hydrostatic drive system, two steel drums containing internal eccentric

weights, and an operator’s platform with a ROPS (Roll Over

Protective Structure). The engine powers the hydraulic systems that

provide machine movement and drum vibration. The vibrating drums

smooth and compact the work surface as the machine moves.

Machine speed, direction, and vibration are controlled by the operator

from the operator’s seat on the platform.

The machine is designed as a lightweight roller to be used in the

compaction of sublayers and finish layers of asphalt on roads,

driveways, parking lots, and other types of asphalt-covered surfaces.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to tow other machines

• Using the machine to spray liquids other than water (i.e., diesel

fuel on asphalt)

• Operating the machine outside of factory specifications.

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Burns from hot hydraulic fluid

• Fire hazards from improper refueling techniques

• Fuel and its fumes

• Personal injury from improper lifting techniques

RD 12 Safety Information

wc_si000516gb.fm 11

• Crushing hazards from improper operation (feet, legs, or arms

extending outside of the operator work station) and for other

persons in the work zone

• Line of sight blockage by the ROPS

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

1.3 Safety Guidelines for Operating the Machine

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

1.3.1

DO NOT drive over curbs or other uneven objects that will result in the

machine and operator being shaken.

1.3.2 DO NOT attempt to start the machine when standing alongside it. Only

start the engine when seated in the driver's seat and with the forward/

reverse control in the neutral position.

1.3.3 Do not allow anyone to operate this equipment without proper training.

People operating this equipment must be familiar with the risks and

hazards associated with it.

1.3.4 Do not touch the engine or muffler while the engine is on or immediately

after it has been turned off. These areas get hot and may cause burns.

WARNING

Safety Information RD 12

12 wc_si000516gb.fm

1.3.5 Do not use accessories or attachments that are not recommended by

Wacker Neuson. Damage to equipment and injury to the user may result.

1.3.6 Never leave the machine running unattended.

1.3.7 NEVER operate the machine with the fuel cap loose or missing.

1.3.8 NEVER carry passengers on the machine. Crushing hazard—keep clear

of the articulated steering joint between the front and rear frames.

1.3.9 NEVER use or attempt to repair damaged safety belts or ROPS. Replace

only with Wacker Neuson spare parts.

1.3.10 ALWAYS disengage and stow the locking bar for the articulated steering

joint before operating the machine. The machine cannot be steered when

the locking bar is engaged.

1.3.11 ALWAYS check that all controls are functioning properly immediately after

start-up! DO NOT operate the machine unless all controls operate

correctly.

1.3.12 ALWAYS remain aware of changing positions and the movement of other

equipment and personnel on the job site.

1.3.13 Always remain seated and wear the seat belt at all times while operating

the machine.

1.3.14 ALWAYS remain aware of changing surface conditions and use extra care

when operating over uneven ground, on hills, or over soft or coarse

material. The machine could shift or slide unexpectedly.

1.3.15 ALWAYS use caution when operating the machine near the edges of pits,

trenches or platforms. Check to be sure that ground surface is stable

enough to support the weight of the machine with operator and that there

is no danger of the roller sliding, falling or tipping.

1.3.16 Always wear protective clothing appropriate to the job site when operating

the machine.

1.3.17 Always keep hands, feet, and loose clothing away from moving parts of the

machine.

1.3.18 Read, understand, and follow procedures in the Operator’s Manual before

attempting to operate the machine.

1.3.19 Store the machine properly when it is not being used. The machine should

be stored in a clean, dry location out of the reach of children.

1.3.20 Always operate the machine with all safety devices and guards in place

and in working order.

1.3.21 Make sure that all other persons are at a safe distance from the machine.

Stop the machine if people step into the working area of the machine.

1.3.22 Do not use a cellphone or send text messages while operating this

machine.

RD 12 Safety Information

wc_si000516gb.fm 13

1.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information RD 12

14 wc_si000516gb.fm

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

1.5.1 Some service procedures require that the machine’s battery be

disconnected. To reduce the risk of personal injury, read and

understand the service procedures before performing any service to

the machine.

1.5.2 All adjustments and repairs MUST be completed before operation. Do not

operate the machine with a known problem or deficiency! All repairs and

adjustments should be completed by a qualified technician.

1.5.3 Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

1.5.4 Do not crank a flooded engine with the spark plug removed on

gasoline-powered engines. Fuel trapped in the cylinder will squirt out

the spark plug opening.

1.5.5 Do not test for spark on gasoline-powered engines if the engine is

flooded or the smell of gasoline is present. A stray spark could ignite

the fumes.

1.5.6 Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

1.5.7 Do not modify the machine without the express written approval of the

manufacturer.

1.5.8 Do not stand under the machine while it is being hoisted or moved.

1.5.9 DO NOT get onto the machine while it is being hoisted or moved.

1.5.10 DO NOT use the machine as a ladder. Use safe ladders and platforms

designed for this purpose.

WARNING

RD 12 Safety Information

wc_si000516gb.fm 15

1.5.11 DO NOT modify, weld, or drill safety frames (ROPS) fitted as original

equipment. DO NOT loosen or remove bolts. DO NOT weld, drill or modify

a broken safety frame.

1.5.12 DO NOT open the hydraulic lines or loosen the hydraulic connections

while the engine is running! Before dismantling the hydraulic connectors

or hoses, ensure that all pressure has been bled from the circuit. Hydraulic

fluid under pressure can penetrate the skin, cause burns, blind, or create

other personal injury hazards. Set all controls in neutral, turn engine off,

and allow the fluids to cool before loosening hydraulic fittings or attaching

test gauges.

1.5.13 ALWAYS check all external fasteners at regular intervals.

1.5.14 Keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

1.5.15 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.5.16 Disconnect the spark plug on machines equipped with gasoline

engines, before servicing, to avoid accidental start-up.

1.5.17 Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions

and warn of dangers and hazards.

1.5.18 ALWAYS do periodic maintenance as recommended in the Operator’s

Manual.

1.5.19 ALWAYS turn the engine off before performing maintenance or making

repairs.

1.5.20 ALWAYS keep hands, feet and loose clothing away from moving parts.

1.5.21 ALWAYS make sure slings, chains, hooks, ramps, jacks, and other

types of lifting devices are attached securely and have enough weight-

bearing capacity to lift or hold the machine safely. Always remain

aware of the location of other people in the area when lifting the

machine.

1.5.22 Always make sure hose connections have been reconnected back to the

correct fitting. Failure to do so may result in damage to the machine and/

or injury to person on or near the machine.

1.5.23 ALWAYS secure the articulated steering joint using the locking bar before

lifting, jacking, and servicing the machine. The machine halves could

swing together unexpectedly and cause a serious injury.

1.5.24 ALWAYS lock the lifting cylinders in the open position when the seat

pedestal is raised.

1.5.25 Before you start the machine, ensure that all tools have been removed

from the machine and that replacement parts and adjusters are firmly

tightened.

Safety Information RD 12

16 wc_si000516gb.fm

1.5.26 Fluid leaks from small holes are often practically invisible. DO NOT use

your bare hands to check for leaks. Check for leaks using a piece of

cardboard or wood.

Notes

RD 12 Labels

wc_si000302gb.fm 17

2 Labels

2.1 Label Locations

X

JJ

FF

GG

HH

GG

Labels RD 12

18 wc_si000302gb.fm

2.2 Label Meanings

Wacker Neuson machines use international pictorial labels where

needed. These labels are described below.

A

WARNING!

Read and understand the supplied Operator’s Manual

before operating the machine. Failure to do so

increases the risk of injury to yourself and others.

B

DANGER!

Asphyxiation hazard.

Engines emit carbon monoxide.

Do not run the machine indoors or in an enclosed

area unless adequate ventilation, through such items

as exhaust fans or hoses, is provided.

Read the Operator’s Manual. No sparks, flames, or

burning objects near the machine. Stop the engine

before refueling.

C

Tie-down point

E

CAUTION!

Read and understand the supplied Operator’s Manual

before operating this machine. Failure to do so

increases the risk of injury to yourself and others.

F

WARNING!

Pinch point.

RD 12 Labels

wc_si000302gb.fm 19

G

WARNING!

Hot surface

H

WARNING!

Hot surface

I

Hydraulic oil reservoir fill tube.

Torque nuts to 13.6-14.7 Nm (120-130 in.lbs.) maxi-

mum.

J

NOTICE

Lifting point.

K

WARNING!

To prevent hearing loss, wear hearing protection when

operating this machine.

M

WARNING!

Disconnect battery before servicing.

Read Repair Manual for instructions.

Battery contains caustic acid and potentially explosive

hydrogen gas.

N

WARNING!

Always wear seat belt when operating roller.

T

Choke:

0 = Open

l = Closed

Labels RD 12

20 wc_si000302gb.fm

U

Grease points: Inspect and lubricate every 100 hours

of operation.

V

WARNING!

Avoid crushing area.

Articulated steering joint locking location. Lock the

articulated steering joint before servicing the machine.

Read Repair Manual.

W

Engine will stop without operator seated.

X

Guaranteed sound power level in dB(A).

Y

A nameplate listing the model number, item number,

revision number, and serial number is attached to

each unit. Please record the information found on this

nameplate so it will be available should the nameplate

become lost or damaged. When ordering parts or

requesting service information, you will always be

asked to specify the model number, item number, revi-

sion number, and serial number of the unit.

Z

No lift point.

La page est en cours de chargement...

Wacker Neuson RD12-90 Manuel utilisateur

Wacker Neuson RD12-90 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents