Yamaha PSR248 Le manuel du propriétaire

2

This product utilizes batteries or an external power supply (adapter).

DO NOT connect this product to any power supply or adapter other

than one described in the manual, on the name plate, or specifically

recommended by Yamaha.

This product should be used only with the components supplied or; a

cart, rack, or stand that is recommended by Yamaha. If a cart, etc.,

is used, please observe all safety markings and instructions that

accompany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE:

The information contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to change

or modify any of the specifications without notice or obligation to

update existing units.

This product, either alone or in combination with an amplifier and

headphones or speaker/s, may be capable of producing sound

levels that could cause permanent hearing loss. DO NOT operate for

long periods of time at a high volume level or at a level that is

uncomfortable. If you experience any hearing loss or ringing in the

ears, you should consult an audiologist.

IMPORTANT: The louder the sound, the shorter the time period

before damage occurs.

NOTICE:

Service charges incurred due to a lack of knowledge relating to how

a function or effect works (when the unit is operating as designed)

are not covered by the manufacturer’s warranty, and are therefore

the owners responsibility. Please study this manual carefully and

consult your dealer before requesting service.

ENVIRONMENTAL ISSUES:

Yamaha strives to produce products that are both user safe and

environmentally friendly. We sincerely believe that our products and

the production methods used to produce them, meet these goals. In

keeping with both the letter and the spirit of the law, we want you to

be aware of the following:

Battery Notice:

This product MAY contain a small non-rechargeable battery which (if

applicable) is soldered in place. The average life span of this type of

battery is approximately five years. When replacement becomes

necessary, contact a qualified service representative to perform the

replacement.

This product may also use “household” type batteries. Some of

these may be rechargeable. Make sure that the battery being

charged is a rechargeable type and that the charger is intended for

the battery being charged.

When installing batteries, do not mix batteries with new, or with

batteries of a different type. Batteries MUST be installed correctly.

Mismatches or incorrect installation may result in overheating and

battery case rupture.

Warning:

Do not attempt to disassemble, or incinerate any battery. Keep all

batteries away from children. Dispose of used batteries promptly and

as regulated by the laws in your area. Note: Check with any retailer

of household type batteries in your area for battery disposal

information.

Disposal Notice:

Should this product become damaged beyond repair, or for some

reason its useful life is considered to be at an end, please observe

all local, state, and federal regulations that relate to the disposal of

products that contain lead, batteries, plastics, etc. If your dealer is

unable to assist you, please contact Yamaha directly.

NAME PLATE LOCATION:

The name plate is located on the bottom of the product. The model

number, serial number, power requirements, etc., are located on this

plate. You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this

manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

SPECIAL MESSAGE SECTION

PLEASE KEEP THIS MANUAL

92-BP (bottom)

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with

the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements

provides a reasonable level of assurance that your use of this

product in a residential environment will not result in harmful

interference with other electronic devices. This equipment

generates/uses radio frequencies and, if not installed and used

according to the instructions found in the users manual, may

cause interference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product

is found to be the source of interference, which can be

determined by turning the unit “OFF” and “ON”, please try to

eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected

by the interference.

Utilize power outlets that are on different branch (circuit breaker

or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results,

please contact the local retailer authorized to distribute this type

of product. If you can not locate the appropriate retailer, please

contact Yamaha Corporation of America, Electronic Service

Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed

by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

(class B)

Entsorgung leerer Batterien (nur innerhalb Deutschlands)

Leisten Sie einen Beitrag zum Umweltschutz. Verbrauchte Batterien oder Akkumulatoren dürfen nicht in den Hausmüll. Sie können bei einer

Sammelstelle für Altbatterien bzw. Sondermüll abgegeben werden. Informieren Sie sich bei Ihrer Kommune.

(battery)

3

• Do not use the instrument near other electrical products such as televisions,

radios, or speakers, since this might cause interference which can affect

proper operation of the other products.

• Do not place the instrument in an unstable position where it might acciden-

tally fall over.

• Before moving the instrument, remove all connected adaptor and other cables.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do

not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do

not use excessive force on the buttons, switches or connectors.

• Use only the stand/rack specified for the instrument. When attaching the

stand or rack, use the provided screws only. Failure to do so could cause

damage to the internal components or result in the instrument falling over.

• Do not operate the instrument for a long period of time at a high or uncomfort-

able volume level, since this can cause permanent hearing loss. If you experi-

ence any hearing loss or ringing in the ears, consult a physician.

■SAVING USER DATA

• Save all data to an external device such as the Yamaha MIDI Data Filer MDF3,

in order to help prevent the loss of important data due to a malfunction or

user operating error.

Yamaha cannot be held responsible for damage caused by improper use or modi-

fications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

Make sure to discard used batteries according to local regulations.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep these precautions in a safe place for future reference.

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts.

If it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• If the AC adaptor cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the instrument, or if any unusual smells

or smoke should appear to be caused by it, immediately turn off the power

switch, disconnect the adaptor plug from the outlet, and have the instrument

inspected by qualified Yamaha service personnel.

• Use the specified adaptor (PA-3B or an equivalent recommended by Yamaha)

only. Using the wrong adaptor can result in damage to the instrument or

overheating.

• Before cleaning the instrument, always remove the electric plug from the

outlet. Never insert or remove an electric plug with wet hands.

• Check the electric plug periodically and remove any dirt or dust which may

have accumulated on it.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the

instrument or other property. These precautions include, but are not limited to, the following:

• Do not place the AC adaptor cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the cord, place

heavy objects on it, or place it in a position where anyone could walk on, trip

over, or roll anything over it.

• When removing the electric plug from the instrument or an outlet, always

hold the plug itself and not the cord.

• Do not connect the instrument to an electrical outlet using a multiple-con-

nector. Doing so can result in lower sound quality, or possibly cause over-

heating in the outlet.

• Unplug the AC power adaptor when not using the instrument, or during

electrical storms.

• Always make sure all batteries are inserted in conformity with the +/- polar-

ity markings. Failure to do so might result in overheating, fire, or battery

fluid leakage.

• Always replace all batteries at the same time. Do not use new batteries to-

gether with old ones. Also, do not mix battery types, such as alkaline batter-

ies with manganese batteries, or batteries from different makers, or different

types of batteries from the same maker, since this can cause overheating,

fire, or battery fluid leakage.

• Do not dispose of batteries in fire.

• Do not attempt to recharge batteries that are not intended to be charged.

• If the instrument is not to be in use for a long time, remove the batteries from

it, in order to prevent possible fluid leakage from the battery.

• Keep batteries away from children.

• Before connecting the instrument to other electronic components, turn off

the power for all components. Before turning the power on or off for all

components, set all volume levels to minimum. Also, be sure to set the

volumes of all components at their minimum levels and gradually raise the

volume controls while playing the instrument to set the desired listening

level.

• Do not expose the instrument to excessive dust or vibrations, or extreme

cold or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disfiguration or damage to the inter-

nal components.

(4)-4

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,

short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

* The illustrations and LCD screens as shown in this owner’s manual are for in-

structional purposes only, and may be different from the ones on your instru-

ment.

1

4

Congratulations on your purchase of

the Yamaha PSR-248 PortaTone!

You now own a portable keyboard that combines advanced functions, great

sound and exceptional ease-of-use in a highly compact package. Its outstanding

features also make it a remarkably expressive and versatile instrument.

Read this Owner’s Manual carefully while playing your new PortaTone in order

to take full advantage of its various features.

PANEL CONTROLS AND TERMINALS 6

●

Front Panel ...................................... 6

●

Rear Panel........................................ 8

SETTING UP 9

POWER REQUIREMENTS ............................ 9

●

Using an AC Power Adaptor ............ 9

●

Using Batteries................................. 9

TURNING ON THE POWER ........................ 9

ACCESSORY JACKS .................................. 10

MUSIC STAND......................................... 10

GETTING STARTED —

PLAYING THE DEMO SONGS 11

PANEL DISPLAY INDICATIONS 12

PORTABLE GRAND 13

USING THE METRONOME....................... 13

●

Setting the Metronome Time

Signature ....................................... 14

●

Adjusting the Metronome Volume . 14

SELECTING AND PLAYING VOICES —

THE VOICE MODE 15

SELECTING AND PLAYING A VOICE......... 15

●

Percussion Voice Chart

(voices 90 and 100). ...................... 17

TRANSPOSE AND TUNING ...................... 18

●

Transpose ...................................... 18

●

Tuning ........................................... 19

TOUCH RESPONSE .................................. 19

SELECTING AND PLAYING SONGS —

THE SONG MODE 20

SELECTING AND PLAYING A SONG......... 20

CHANGING THE TEMPO ......................... 21

●

About the Beat Display .................. 22

ADJUSTING THE SONG VOLUME ............ 23

SONG CONTROLS .................................. 24

A/B REPEAT .............................................. 24

MELODY GUIDE ....................................... 26

VOICE CHANGE ........................................ 27

SELECTING AND PLAYING STYLES —

THE STYLE MODE 28

SELECTING AND PLAYING A STYLE.......... 28

STYLE CONTROLS ................................... 30

USING THE AUTO ACCOMPANIMENT

FEATURES ............................................. 31

CHANGING THE TEMPO ......................... 31

STYLE SECTIONS (MAIN A, MAIN B) AND

FILL-INS ................................................ 32

ADJUSTING THE ACCOMPANIMENT

VOLUME .............................................. 32

USING AUTO ACCOMPANIMENT —

MULTI FINGERING................................ 33

●

Single Finger Chords ..................... 33

●

Fingered Chords ............................ 33

WHAT IS A CHORD? ................................ 34

WRITING CHORD NAMES ....................... 35

●

The Intervals of the Scale ............... 35

●

Other Chords ................................ 35

ONE TOUCH SETTING (OTS) ................... 36

CHORD GUIDE .......................................... 37

●

Smart ............................................ 37

●

Dictionary...................................... 39

MULTI PADS ............................................. 40

MIDI 41

●

About MIDI ................................... 41

●

How Can MIDI be Used? ............... 41

TROUBLESHOOTING ...................................... 42

INDEX ............................................................ 43

VOICE LIST ..................................................... 44

MULTI PAD LIST.............................................. 46

SPECIFICATIONS ............................................ 47

MIDI IMPLEMENTATION CHART..................... 48

Contents

2

5

Portable Grand

Yamaha Education Suite

The PortaTone also has a Portable Grand function for realistic piano performance. Pressing the

PORTABLE GRAND button instantly calls up the stunningly authentic “Stereo Sampled Piano” voice

and configures the entire PortaTone for optimum piano play. Special Piano styles — with piano-only

accompaniment — are also provided.

The PSR-248 is a sophisticated yet easy-to-use keyboard with the following fea-

tures and functions:

Main Features

The PortaTone features the new Yamaha Education Suite — a set of learning tools that utilize the latest

technology to make studying and practicing music more fun and fulfilling than ever before!

The Yamaha Education Suite includes:

Powerful Melody Guide functions in the Song mode — Waiting and Minus One — that let you

easily learn the 100 songs and even show you what notes to play!

• Waiting pauses song playback (like a patient teacher!), so you can practice at your own pace.

• Minus One mutes only the melody part, letting you play the part yourself. The expert

backing parts encourage you to play your best and make it easy to “feel” the song!

Chord Guide functions in the Style mode — Smart and Dictionary — that make it exceptionally

easy to learn chords and chord relationships.

• Smart lets you easily play harmonically “correct” chord progressions for whatever key you

specify. It’s great for learning — and performing!

• Dictionary is a built-in “chord encyclopedia” that teaches you how to play specific chords.

You type in the chord name, and the PortaTone shows you which notes to play!

page 26-27, 34-35, 37-39

page 13

Other powerful features include:

• Exceptionally realistic and dynamic sounds with

100 voices, utilizing digital recordings of actual

instruments.

• Touch Response lets you dynamically and expres-

sively control the volume of the voices with your

playing strength — just as on an acoustic piano.

• 100 dynamic auto accompaniment Styles, each

with different Intro, Main A and B, and Ending

sections. All styles (except for the Piano styles) also

have their own four Fill-in patterns.

•

Large custom LCD gives you easy, at-a-glance confirma-

tion of all important settings, as well as chord and note

indications.

• 100 songs, for your listening enjoyment — or for

use with the sophisticated learning tools of the

Yamaha Education Suite.

•

Convenient control over accompaniment Styles —

including Tempo and independent Accompaniment

Volume.

• One Touch Setting (OTS), for automatically calling

up an appropriate voice for playing with the selected

Style.

• MIDI terminals for interfacing with other MIDI

devices. The PSR-248 also has a Sustain switch jack.

• Built-in, high-quality stereo amplifier/speaker

system.

3

6

Panel Controls and Terminals

Front Panel

M

1 2 2

1

L

LH H

H L

H

B

C

S

BS L M H

MIN MAX

METRONOME

SMART

DICTIONARY

OFF

WAITING

MINUS ONE

OFF

AUTO FILL

MAINAB

rit.

INTRO/

ENDING

ACMP

ON/OFF

SYNC-

START

START/

STOP

CHORD

GUIDE

OTS

MELODY

GUIDE

VOICE

CHANGE

M

m

aug

dim

7 M7

sus4

m7 mM7 7 5

m7 5 7sus4 m6

(

9

)

C

C D

D

D E

E F

F G

G

K

C

K

D

IUM

A

LLAD

ROCK SHUFFLE

CUMBIA

SLOW ROCK

6/8 HVY ROCK

US ROCK

16BEAT ROCK

R&B

SOUL

FUNK

ALLAD

BALLAD

B

EAT POP

T

SHUFFLE

6BT BALLAD

F

USION BALLAD

C

E

O

CHU

R

FULL

O

WAVE O

R

ACCORDI

O

HARMONIC

A

SOFT GUITAR

FOLK GUITAR

12ST GUITAR

JAZZ GUITAR

E GUITAR

DIST GUITAR

P

WOOD BASS

FINGER BASS

MUTE BASS

SLAP BASS

SOUL BALLAD

GPL SHUFFLE

6/8 GOSPEL

SWING

B B SWING

B B BALLAD

JZ QUARTET

DIXIELAND

COOL JAZZ

JAZZ BALLAD

JAZZ WALTZ

4/4 BLUES

ROCK & ROLL

BOOGIE

TWIST

BOSSA NOVA

SALSA

SAMBA

MAMBO

DANCE POP

TECHNO

EUROBEAT

EURO HOUSE

HIP HOP

70S DISCO

DISCO TROP

8BT ROCK BLD

16BT ROCK BLD

6/8BALLAD

HARD ROCK

BLUEGRASS

2/4 COUNTRY

8BT COUNTRY

CBY BOOGIE

CTY BALLAD

CTY SHUFFLE

CTY WALTZ

CAJUN

BANDA

BEGUINE

MERENGUE

BLR LENTO

REGGAE 1

REGGAE 2

RHUMBA

TANGO

FOXTROT

JIVE

ARPEGGIO 1

ARPEGGIO 2

ARPEGGIO 3

DANCE POP

ROCK PIANO

ROCK & ROLL

TIGHT ROCK

SWING

JAZZ WALTZ

RAGTIME

BEGUINE

CHA CHA

MARCH

MARIACHI

TEJANO

6/8 MARCH

GALOPMARCH

FUSION

6/8 MARCH

POLKA

STD WALTZ

POP WALTZ

GMN WALTZ

VIEN WALTZ

2BEAT

8BEAT

HONKY-TONK

PIANO BALLAD

POP BALLAD

TEMPO

GrandPno

001

116

A

B

Q

G

O

P

D

E

F

C

R S

H I

J

K

L

M

N

4

7

A Power switch (STANDBY/ON)

B MASTER VOLUME dial

This determines the overall volume of the

PortaTone.

C OVERALL buttons

(s, t, +, -)

These are for selecting the various “overall”

functions and setting their values. (See page 23.)

D SONG button

This selects the Song mode. (See page 20.)

5 STYLE button

This selects the Style mode. (See page 28.)

6 VOICE button

This selects the Voice mode. (See page 15.)

G Numeric keypad, +/- buttons

These are for selecting songs, voices, and styles.

(See page 16.) They are also used for entering

certain values, such as the time signature for the

Metronome (page 14), and the key signature for

the Smart Chord function (page 38).

H ACMP ON/OFF button

When the Style mode is selected, this turns the

auto accompaniment on and off. (See page 31.)

This button has no function in the Song mode.

I SYNC-START, Pause (❙❙) button

When the Style mode is selected, this turns the

Sync-Start function on and off. (See page 29.)

When the Song mode is selected, this alternately

pauses and starts song playback. (See page 24.)

J START/STOP (>/■) button

When the Style mode is selected, this alternately

starts and stops the auto accompaniment. (See

page 29.) When the Song mode is selected, this

alternately starts and stops song playback. (See

page 24.)

K INTRO/ENDING, button

When the Style mode is selected, this is used to

control the Intro and Ending functions. (See

pages 29, 30.) When the Song mode is selected,

this is used to control the A/B Repeat function.

(See page 24.)

L MAIN A/B (AUTO FILL), Fast Forward

(f)/Rewind (r) buttons

When the Style mode is selected, these are used to

change auto accompaniment sections and control

the Auto Fill function. (See page 32.) When the

Song mode is selected, these are used to respec-

tively fast forward and rewind during song play-

back. When Song playback is stopped, they can be

used to advance or reverse to specific measure

numbers in the song. (See page 24.)

M OTS, VOICE CHANGE button

When the Style mode is selected, this is used to

turn the One Touch Setting (OTS) function on and

off. (See page 36.) When the Song mode is

selected, this is used to turn the Voice Change

function on and off. (See page 27.)

N CHORD GUIDE, MELODY GUIDE button

When the Style mode is selected, this is used to

control the Chord Guide functions. (See page 37.)

When the Song mode is selected, this is used to

control the Melody Guide function. (See page

26.)

O PORTABLE GRAND button

This instantly changes to the Voice mode and calls

up the Grand Piano voice. (See page 13.)

P METRONOME button

This turns the metronome on and off. (See page

13.)

Q MULTI PAD buttons

These are used to automatically play pre-pro-

grammed musical phrases. (See page 40.)

R DEMO button

This is used to play the Demo songs. (See page 11.)

S TOUCH button

This turns the Touch Response function on and off.

It also lets you set the Touch Sensitivity setting.

(See page 19.)

Panel Controls and Terminals

5

8

T DC IN 10-12V jack

This is for connection to a PA-3B AC power

adaptor. (See page 9.)

PHONES/OUTPUT jack

This is for connection to a set of stereo head-

phones or to an external amplifier/speaker

system. (See page 10.)

Rear Panel

SUSTAIN jack

This is for connection to an optional FC4 or FC5

Footswitch. (See page 10.)

MIDI IN, OUT terminals

These are for connection to other MIDI instru-

ments and devices. (See pages 10, 41.)

Panel Controls and Terminals

PHONES/

OUTPUT

DC IN 10-12V

T

IN OUTMIDI

SUSTAIN

6

9

This section contains information about setting up your PortaTone for playing.

Make sure to read this section carefully before using the instrument.

Setting Up

Power Requirements

Although the PSR-248 will run either from an

optional AC adaptor or batteries, Yamaha

recommends use of an AC adaptor whenever

possible. An AC adaptor is more environmen-

tally friendly than batteries and does not deplete

resources.

Using an AC Power Adaptor

To connect your PortaTone to a wall socket, you

will need the optionally available Yamaha PA-3B

Power Adaptor. Use of other AC adaptors could

result in damage to the instrument, so be sure

to ask for the right kind. Connect one end of

the adaptor to the DC IN 10-12V jack on the

rear panel of your PortaTone, and the other end

to a suitable electrical outlet.

WARNING

• Use ONLY a Yamaha PA-3B AC Power Adaptor (or other

adaptor specifically recommended by Yamaha) to power your

instrument from the AC mains. The use of other adaptors may

result in irreparable damage to both the adaptor and the PSR-

248.

• Unplug the AC Power Adaptor when not using the PSR-248,

or during electrical storms.

Using Batteries

■ Inserting Batteries

Turn the instrument upside-down and remove

the battery compartment lid. Insert six 1.5-volt

size “D” (SUM-1, R-20 or equivalent) batteries

as shown in the illustration, making sure that

the positive and negative terminals are properly

aligned, and replace the lid.

■ When the Batteries Run Down

When the batteries run low and the battery

voltage drops below a certain level, the

PortaTone may not sound or function properly.

As soon as this happens, replace them with a

complete set of six new batteries.

CAUTION

• Never mix old and new batteries or different types of

batteries (e.g., alkaline and manganese).

• To prevent possible damage from battery leakage, remove

the batteries from the instrument if it is not to be used for a

long time.

CAUTION

• Even when the switch is in the “STANDBY” position,

electricity is still flowing to the instrument at the minimum

level. When you are not using the PSR-248 for a long time,

make sure you unplug the AC power adaptor from the wall AC

outlet, and/or remove the batteries from the instrument.

Turning On the Power

With the AC power adaptor connected or with

batteries installed, simply press the STANDBY

switch until it locks in the ON position. When

the instrument is not in use, be sure to turn the

power off. (Press the switch again so that it

pops up.)

BATTERIES 1.5V

x

6

7

10

NOTE:

• Make sure that the footswitch plug is properly connected to

the SUSTAIN jack before turning on the power.

• Do not press the footswitch while turning the power on.

Doing this changes the recognized polarity of the footswitch,

resulting in reversed footswitch operation.

■ Using the MIDI Terminals

The PortaTone also features MIDI terminals,

allowing you to interface the PortaTone with

other MIDI instruments and devices. (For more

information, see page 41.)

Music Stand

Insert the bottom edge of the included music

stand into the slot located at the top rear of the

PortaTone control panel.

Setting Up

SUSTAIN

IN OUTMIDI

MIDI instrument

■ Using a Sustain Footswitch

This feature lets you use an optional footswitch

(Yamaha FC4 or FC5) to sustain the sound of

the keyboard voice. This is used in the same

way as a damper pedal on an acoustic piano —

press and hold down the footswitch as you play

the keyboard to sustain the sound.

Accessory Jacks

■ Using Headphones

For private practicing and playing without

disturbing others, connect a set of stereo head-

phones to the rear panel PHONES/OUTPUT jack.

Sound from the built-in speaker system is auto-

matically cut off when you insert a headphone

plug into this jack.

■ Connecting a Keyboard Amplifier or Stereo

System

Though the PortaTone is equipped with a built-

in speaker system, you can also play it through

an external amplifier/speaker system. First,

make sure the PortaTone and any external

devices are turned off, then connect one end of

a stereo audio cable to the LINE IN or AUX IN

jack(s) of the other device and the other end to

the rear panel PHONES/OUTPUT jack on the

PortaTone.

CAUTION

• To prevent damage to the speakers, set the volume of the

external devices at the minimum setting before connecting

them. Failure to observe these cautions may result in electric

shock or equipment damage. Also, be sure to set the volumes

of all devices at their minimum levels and gradually raise the

volume controls while playing the instrument to set the

desired listening level.

8

11

Getting Started —

Playing the Demo Songs

The PortaTone has a huge variety of Demo songs, specially recorded to showcase

the dynamic sounds and rhythms and give you an idea of what you can do with

the instrument.

First, turn on the power.

Press the STANDBY/ON button. Whenever the power is

turned on, the Voice mode is automatically called up

and set to play Voice 1 (GrandPno).

Set the Volume.

Initially, turn the MASTER VOLUME control about a third

of the way up. You can adjust the control for optimum

level once the songs start playing.

Press the DEMO button.

All 100 songs will play in sequence. You can play along on the keyboard

with the songs. If the Voice Change function is on (page 27), the key-

board voice will change to match the changes in the song of the melody

voice.

The current song name and number appear at the left of the display.

Notice also that the display indicates both the chords (except for song #1,

“StarWars”) and the melody notes (in the music staves and the keyboard

diagram) as they change during the song. (Scores for the Demo songs are

provided.)

To stop playback, press the START/STOP (>/■)

button. For information on selecting and playing

individual songs, see page 20.

While the Demo song is playing...

Many features of the PortaTone can be used while the

Demo songs are playing. These include:

• Tempo (page 21)

• Song volume (page 23)

• Tuning (page 19)

• Pause (❙❙), Rewind (r), Fast Forward (f) (page 24)

• Voice Change (page 27)

StarWars

001

002

MEASURE

Song name

Song number

Current chord

Melody notation

Keyboard diagram

(current note is dark)

MIN MAX

9

12

A Mode indicator

These dark bars indicate the currently selected

mode: Song, Voice, or Style. A C-shaped bar (at

SONG or STYLE) indicates that the mode is active

in the background.

In the first example, the Song mode is selected. In

the second example, the Voice mode is selected,

but the Song mode is active in the background.

(This means that the song controls below the

display are active and can be used to play the

currently selected song.)

Panel Display Indications

The PortaTone features a large multi-function display that shows all important

settings for the instrument. The section below briefly explains the various icons

and indications in the display.

NOTE:

The LCD’s backlight will gradually dim over a long period of use. When the display becomes dim or hard to read, contact the store

where you purchased the instrument or, Yamaha directly, to have the LCD replaced. A fee will be charged for replacement.

active, the display also shows the

specific notes of the current chord.

The indication “8va” appears at the

lower or upper part of the notation

staff for a note or notes that are

respectively an octave lower or

higher than notated.

NOTE:

For a few specific chords (such as BM7), not all notes may be

shown in the notation section of the display. This is due to

space limitations in the display.

E Measure/Tempo and beat

This shows either the current measure (when the

Song mode is selected) or the current Tempo

value (when the Style mode is selected). The

hand clap icons also flash to indicate the beats in

the measure during song or style playback. (See

page 22.)

F Chord

When a song is being played back, this indicates

the current chord root and type. It also indicates

chords played in the ACMP section of the key-

board when the Style mode and auto accompani-

ment are on.

G Song/Voice/Style name and number

This portion of the display indicates the name and

number of the currently selected song, voice, or

style. When other functions of the PortaTone are

selected, it briefly shows the function name and

current value or setting.

B Overall function bar indicator

The PortaTone has seven Overall functions or

controls. The currently selected function is indi-

cated by a dark bar that appears next to its name

(printed on the panel).

C Notation

D Keyboard

These two portions of the display conveniently

indicate notes currently played on the keyboard.

When a song is being played back, they show the

single notes of the melody in succession. When

the Style mode and auto accompaniment are

EX.1

Song

mode

EX.2

Song

mode

Voice

mode

003

8va

12

A Mode indicator

B Overall function

bar indicator

C Notation

D Keyboard

E Measure/Tempo

and beat

F Chord

G Song/Voice/Style name

and number

WholeNew

002

003

MEASURE

METRONOME VOL

SONG VOL

ACMP VOL

TUNING

TRANSPOSE

MULTI PAD

TEMPO

10

13

Using the Metronome

Set the desired tempo with the Tempo function in

the Overall menu.

Press one of the OVERALL s/t buttons, repeatedly if necessary, until

“Tempo” appears in the display.

Change the value.

Use the OVERALL +/- buttons to increase or

decrease the Tempo value. Holding down either

button continuously increases or decreases the

value.

Press the piano-shaped PORTABLE GRAND button.

Doing this automatically cancels any other mode or function, and resets

the entire instrument for playing the special “Stereo Sampled Piano”

Grand Piano voice (voice 001). It automatically selects the Song mode,

calling up song #72, “Für Elise” — which can be played instantly by

pressing the START/STOP (>/■) button. It also sets the Multi Pads to

special piano phrases, and calls up style #81 (“2beat”).

METRONOME

Portable Grand

This convenient function lets you automatically exit from any

other mode or function and instantly call up the Grand Piano

voice.

Turn on the Metronome.

Press the METRONOME button.

To turn the Metronome off, press the METRONOME

button again.

METRONOME

Increases

Tempo value

Decreases

Tempo value

TEMPO

Tempo

116

TEMPO

Current Tempo value

11

14

You can adjust the volume of the Metronome sound

independently of the other PortaTone sounds. The

volume range is 000 - 127.

The time signature of the Metronome can be set to

various quarter-note based meters.

NOTE:

The time signature changes automatically when a style

or song is selected.

Simultaneously hold down the METRONOME

button and press the button on the numeric

keypad that corresponds to the desired time

signature (see chart at right).

Change the value.

Use the OVERALL +/- buttons to increase or

decrease the Metronome Volume value. Holding

down either button continuously increases or

decreases the value.

Numeric Time

keypad signature

1 Plays only “1” beats (all high clicks)

2 2/4

3 3/4

4 4/4

5 5/4

6 6/4

7 7/4

8 8/4

9 9/4

0 Plays no “1” beats (all low clicks)

Setting the Metronome Time Signature

Adjusting the Metronome Volume

Portable Grand

Select the Metronome Volume function

in the Overall menu.

Press one of the OVERALL s/t buttons, repeatedly

if necessary, until “MtrVol” appears in the display.

Increases Metro-

nome Volume value

Decreases Metronome

Volume value

TEMPO

MtrVol

100

116

METRONOME VOL

Current Metronome value

Restoring the Default Metronome Volume Value

To restore the default Metronome Volume value

(100), press both OVERALL +/- buttons simulta-

neously (when Metronome Volume is selected in

the Overall menu).

12

15

The Voice mode features 100 authentic voices that have been

created with Yamaha’s sophisticated AWM (Advanced Wave

Memory) tone generation system. Many of these voices also

have special preset characteristics or embellishments. The

voices are divided into various categories depending on their

characteristics or the effects used.

Selecting and Playing Voices —

The Voice Mode

Selecting and Playing a Voice

Select the Voice mode.

Press the VOICE button.

Select the desired voice number.

Use the numeric keypad. The basic categories of voices and their num-

bers are shown at the right side of the panel. A complete list of the

available voices is given on page 44.

Voice list

GRAND PIANO

PIANO

HONKY-TONK

E PIANO 1~4

HARPSICHORD

CLAVI

CELESTA

E ORGAN 1~4

CHURCH ORG 1~2

STRINGS

VIOLIN

CELLO

HARP

SITAR

BANJO

UKULELE

VIBRAPHONE

MARIMBA

STEEL DRUMS

THICK LEAD

SIMPLE LEAD

THICK SAW

SIMPLE SAW

SYNTH BASS

SY STRINGS

SY BRASS 1~2

RISING

SLOW STRS

HARMONY

SPLIT

ECHO

DUAL

DRUM KIT

FULL ORGAN

WAVE ORGAN

ACCORDION

HARMONICA

TRUMPET

TROMBONE

MUTE TRPET

SOFT GUITAR

FOLK GUITAR

12ST GUITAR

JAZZ GUITAR

E GUITAR

DIST GUITAR

BRASS SECT

FRENCH HORN

ALTO SAX

TENOR SAX

CLARINET

STAR WARS MAIN TITLE

A WHOLE NEW WORLD

CHRISTMAS

FAVORITE

CHILDREN

FLUTE

PAN FLUTE

WOOD BASS

FINGER BASS

MUTE BASS

SLAP BASS

Indicates Voice mode is

selected

Voice name and number

TEMPO

GrandPno

001

116

13

16

There are three ways to select voices: 1) directly

entering the voice number with the numeric

keypad, 2) using the +/- keys to step up and

down through the voices, or 3) pressing the

VOICE button to advance through the voice

numbers.

Using the numeric keypad

Enter the digits of the voice number as printed

on the panel. For example, to select voice #42,

press “4” on the numeric keypad, then “2.”

Using the +/- keys

Press the + key to select the next voice number,

and press the - key to select the previous voice.

Holding down either key continuously scrolls up

or down through the numbers. The +/- keys

have a “wrap around” feature. For example,

pressing the + key from the voice 100 returns to

voice 1.

Using the VOICE button

Press the VOICE button to select the next voice

number. (This functions exactly the same as the

+ button.)

NOTE:

Each voice is automatically called up with the most suitable

octave range setting. Thus, playing middle C with one voice

may sound higher or lower than another voice at the same

key.

Selecting and Playing Voices — The Voice Mode

TEMPO

Trombone

042

116

NOTE:

When selecting Voice numbers 1 - 10, the PortaTone pauses

briefly before changing to the voice. (However, you can

quickly select the voice by pressing all three digits; for

example, select voice #9 by pressing “0,” “0,” then “9.”)

Pressing only “0” does not change the voice.

14

17

Play the selected voice.

To change to another voice, repeat step 2 above.

If the Song or Style mode is active in the background (indi-

cated by a C-shaped bar in the display), you can also play

songs or styles, respectively, in the Voice mode by simply

pressing the START/STOP (>/■) button. The last selected

song or style will be played.

NOTE:

The PortaTone is polyphonic up to a

maximum of 16 notes. (Depending on

the voice selected — such as split voices

and dual voices — fewer notes may be

available.) This includes not only the

notes played from the keyboard, but also

the notes in a style pattern, the notes

played by a Pad (page 40), and so on.

Thus, if you play too many notes at one

time, some may not sound and/or others

may be cancelled.

■ Percussion Voice Chart (voices 90 and 100)

Selecting and Playing Voices — The Voice Mode

M

H

1 2 21

L

LH

L

H L

H

B

C

S

BS L M H

M

m

aug

dim

7 M7

sus4

m7 mM7 7 5

m7 5 7sus4 m6

(

9

)

C

C D

D

D E

E F

F G

G

G A

A

A B

B

Rim Shot

Bass Drum 1

Bass Drum 2

Hi-hat Close

Snare Drum 1

Hi-hat Pedal

Snare Drum 2

Hi-hat Open

Tom Bass

Tom Low

Crash Cymbal

Tom Mid

Splash Cymbal

Tom High

SynthBass Drum

Cowbell

SynthSnare Drum

Claves

Synth Tom Bass

Shaker

Synth Tom Low

Synth Tom Mid

Timbale H

Synth Tom High

Timbale L

Agogo H

Agogo L

Conga H Mute

Bongo H

Conga H Open

Bongo L

Conga L

Guiro Short

Guiro Long

Harmony voices (#61 - #70) automatically add a

one-, two- or three-note harmony to the origi-

nal voice. Split voices (#71 - #80) feature two

separate voices, each playable from opposite

sections of the keyboard — the lower voice

playable up to B2 and the upper voice from C3

(middle C). Echo voices (#81 - #90) provide an

echo effect that adds delayed repeats to the

original voice. Dual voices (#91 - #99) blend

two voices together for a rich, layered sound.

Also included are special Percussion voices —

#90 (with Echo) and #100 — that let you play

various drum and percussion sounds from the

keyboard. (Refer to the Percussion Voice chart

below.) Symbols are also printed above the

keyboard, conveniently indicating which sounds

are played from which keys.

NOTE: About the Harmony voices

Since Harmony voices are designed to automatically play two

or more notes with the notes you play on the keyboard, only

one note can be played on the keyboard at a time. If several

notes are played together, only the last note or highest note

played will be used for the harmony effect.

The type of harmony used depends on the

particular voice that is selected.

15

18

Selecting and Playing Voices — The Voice Mode

Transpose and Tuning

You can also adjust the tuning and change the transposition (key) of the PortaTone with the Trans-

pose and Tuning functions.

Transpose

Transpose determines the key of both the main voice and the bass/chord accompaniment of the

selected style. It also determines the pitch of the songs and the Multi Pads. This allows you to easily

match the pitch of the PortaTone to other instruments or singers, or play in a different key without

changing your fingering. The Transpose settings can be adjusted over a range of ± 12 semitones (± 1

octave).

Select the Transpose function in the Overall menu.

Press one of the OVERALL s/t buttons, repeatedly if necessary, until “Tun-

ing” appears in the display.

Change the value.

Use the OVERALL +/- buttons to increase or decrease the Transpose value.

Holding down either button continuously increases or decreases the value.

Restoring the Default Transpose Value

If you’ve changed the Transpose setting, you can instantly

restore the default setting of “00” by pressing both

OVERALL +/- buttons simultaneously (when Transpose is

selected in the Overall menu).

NOTE:

This setting has no effect on the DrumKit voice (#90, #100).

Also, this setting cannot be changed during song playback.

Increases

Transpose value

Decreases

Transpose value

TEMPO

Transpos

00

116

TRANSPOSE

Current Transpose value

16

19

Select the Tuning function in the Overall menu.

Press one of the OVERALL s/t buttons, repeatedly if necessary, until “Tuning” appears in the

display.

Tuning

Tuning determines the fine pitch setting of both the main voice and the bass/chord accompaniment

of the selected style. It also determines the pitch of the songs and the Multi Pads. This allows you to

accurately match the tuning with that of other instruments. The Tuning settings can be adjusted over

a range of ± 50 (approx. ± 0.5 semitones).

Change the value.

Use the OVERALL +/- buttons to increase or decrease the Tuning

value. Holding down either button continuously increases or

decreases the value.

Restoring the Default Tuning Value

If you’ve changed the Tuning setting, you can instantly restore the default

setting of “00” by pressing both OVERALL +/- buttons simultaneously (when

Tuning is selected in the Overall menu).

Selecting and Playing Voices — The Voice Mode

Increases

Tuning value

Decreases

Tuning value

Touch response

Current Tuning value

The PortaTone features a Touch Response function that gives you dynamic, expressive control over

the volume of the voices. The Touch Sensitivity parameter lets you set the degree of Touch Response.

To turn on Touch Response, press the TOUCH button.

Change the Touch Sensitivity value.

Simultaneously hold down the TOUCH button, and press

the appropriate numbered button on the numeric keypad:

1, 2, or 3.

A setting of “1” results in a narrow dynamic range, no

matter how lightly or strongly you play the keys. A setting

of “2” provides a normal dynamic range from soft to loud,

while “3” (default setting) results in a wide dynamic range

that lets you play from very soft to very loud.

+

TEMPO

Tuning

00

116

TUNING

17

20

Selecting and Playing Songs —

The Song Mode

The Song mode features 100 special songs that have been created using the rich

and dynamic sounds of the PortaTone.

The songs are generally for your listening enjoyment; however, you can also play along with them on

the keyboard. A Voice Change function lets you set whether the keyboard voice changes or not with

the voice changes in the song itself. Also, by using the Minus One function, you can “mute” the

original melody and play it manually on the keyboard yourself.

Selecting and Playing a Song

Select the Song mode.

Press the SONG button.

Select the desired song number.

Use the numeric keypad. The basic categories of songs and

their numbers are shown at the right of the panel.

Song numbers can be selected in the same way as with the

voices (see page 16). You can use the numeric keypad to

directly enter the song number, use the +/- keys to step up

and down through the songs, or press the SONG button to

advance through the song numbers.

Start the selected song.

Press the START/STOP (>/■) button. As the song plays back,

the measure number, chords and melody notes are shown in

the display.

AUTO F

MAIA

rit.

INTRO/

ENDING

SYNC-

START

START/

STOP

Indicates Song mode is

selected

StarWars

001

MEASURE

Song name and number

18

La page charge ...

Yamaha PSR248 Le manuel du propriétaire

Yamaha PSR248 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents