Regency Fireplace Products F3500 Le manuel du propriétaire

Marque: Regency Fireplace Products

Modèle: F3500

Catégorie: Poêles

Taper: Le manuel du propriétaire

Ce manuel convient également à

Pro-Series F3500

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-552f

MODEL: F3500

Pro Series Freestanding Woodstove

12.10.19

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Owners &

Installation Manual

www.regency-ﬁre.com

French Manual Download: http://ow.ly/Zv1Hq

Manuel en Français: http://ow.ly/Zv1Hq

0219WS018S

Tested by:

F3500 Regency Freestanding Woodstove

Thank-you for purchasing a

REGENCY FIREPLACE PRODUCT.

The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you have any questions about

your product that are not covered in this manual, please contact the REGENCY DEALER in your area.

“This wood heater has a manufacturer set minimum low burn rate that must not be altered. It is against federal regulations to alter this setting or

otherwise operate this wood heater in a manner inconsistent with operating instructions in this manual.” Failure to follow the manual details

can lead to smoke and CO emissions spilling into the home. It is recommended to have monitors in areas that are expected to generate CO

such as heater fueling areas.

“U.S. ENVIRONMENTAL PROTECTION AGENCY Certiﬁed to comply with 2020 particulate emission standards using cord wood.”

Tested and listed to ASTM E3053 Model Regency F3500 – 0.9 g /hr.

“This manual describes the installation and operation of the Regency F3500 catalytic equipped wood heater. This heater meets the 2020 U.S.

Environmental Protection Agency’s crib wood emission limits for wood heaters. Under speciﬁc test conditions this heater has been shown to

deliver heat at rates ranging from 10,704 BTU/hr. to 36,174 BTU/hr.” Efﬁciency is determined using the B415 method resulting in lower and higher

heat values. This heater generates the best efﬁciency when operated using well-seasoned wood and installed in the main living areas where the

majority of the chimney is within the building envelope. "This wood heater contains a catalytic combustor, which needs periodic inspection and

replacement for proper operation.

It is against federal regulation to operate this wood heater in a manner inconsistent with operating instructions in this manual, or if the

catalytic element is deactivated or removed."

CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESERVATIVES, METAL FOILS, COAL,

PLASTIC,GARBAGE, SULPHUR OR OIL MAY DAMAGE THE CATALYST

"This heater is designed to burn natural wood only. Higher efﬁciencies and lower emissions generally result when burning air dried seasoned

hardwoods, as compared to softwoods or to green or freshly cut hardwoods."

DO NOT BURN:

• Treated wood • Lawn clippings or yard waste • Manure or animal remains

• Coal • Materials containing rubber including tires • Saltwater driftwood or other previously salt water

saturated materials

• Garbage • Materials containing plastic • Unseasoned wood

• Cardboard • Waste petroleum products , paints or paint thinners or asphalt products • Paper products, cardboard, plywood or particle

board. The prohibition against burning these

materials does not prohibit the use of ﬁre starters

made from paper, cardboard, saw dust, wax and

similar substances for the purpose of starting a

ﬁre in a wood heater.

• Solvents • Materials containing asbestos

• Colored Paper • Construction or demolition debris

• Trash • Railroad ties

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

The authority having jurisdiction (such as Municipal Building Department, Fire Department, Fire Prevention Bureau, etc.) should be

consulted before installation to determine the need to obtain a permit.

Note: Due to the high efﬁciency of the F3500 unit. Double wall pipe is recommended from the stove top to either wall or roof exit. A minimum of

36" vertical rise is required prior to using any elbows.

This unit must be connected to either a listed factory built chimney suitable for use with solid fuels and conforming to, ULC629 in Canada or UL-

103HT in the United States of America. or code approved masonry chimney with ﬂue liner.

F3500 is tested and certiﬁed to ULC-S627-00 and UL1482-2011 (R 2015).

SAVE THESE INSTRUCTIONS

F3500 Regency Freestanding Woodstove

table of

contents

Safety Label for F3500 ..................................................4

Unit Dimensions ............................................................5

Wood Stove Outside Air Dimensions .............................6

Residential Installation ...................................................7

Modular Installation Options ..........................................7

Room Air - Important .....................................................7

Stove Assembly

Prior To Installation ........................................................8

Minimum Clearance To Combustible Materials ..............9

Wall exit Clearance Factory Built Chimney ..................10

Masonry Fireplace .......................................................11

Combustible Wall Chimney Connector Pass-throughs 12

Step-by-step Chimney And Connector Installation ......14

Recommended Heights For Woodstove Flue ..............15

Mobile Home Installation .............................................16

Optional outside air kit ................................................17

Listed Components For Mobile Home Installation .......18

Stainless steel smoke deﬂector

Installation / replacement: ............................................19

Brick Installation ..........................................................20

Removable door handle ...............................................21

Fan Installation ...........................................................22

Seasoned Firewood .....................................................23

Operating Instructions .................................................24

Draft Control ................................................................24

First Fire ......................................................................24

Fan Operation ..............................................................25

Ash Disposal ................................................................25

Safety Guidelines and Warnings .................................25

Maintenance ................................................................27

Creosote ......................................................................27

Door Catch Adjustment ...............................................27

Door Gasket ................................................................27

Glass Maintenance ......................................................27

Wood Storage ..............................................................27

Glass Replacement .....................................................27

Catalytic combustor ....................................................28

Bypass door gasket replacement ...............................30

Secondary air tube removal / installation .....................31

door catch Adjustment .................................................31

F3500 Stove Main Assembly .......................................33

F3500 Stove brick layout .............................................34

Door assembly ............................................................35

Warranty .....................................................................36

CAUTION: To avoid burns or wood splinters, when opening/closing the fuel

door or adding wood to the ﬁre, You should always wear appropriate protective

gloves to protect your hands from the heat being emitted from this ﬁreplace.

F3500 Regency Freestanding Woodstove

SAFETY LABEL

safety decal

This is a copy of the label that accompanies each

Regency Freestanding Woodstove (F3500).

We have printed a copy of the contents here

for your review.

NOTE: Regency units are constantly being

improved. Check the label on the unit and if

there is a difference, the label on the unit is the

correct one.

Part #: 919-337b

Size: 12-5/8" H x 5-3/4" W (File at 100%)

Color: Everything printed black on grey except what is indicated is printed red on grey.

Material: 2 ml silver matt polyester (DPM SMS)

Jan 13/14: Created draft.

Apr. 4/14: Updated as per Dave L

Apr. 16/14: Updated as per Dave L

May 06/15: Updated yrs. of manufacture/removed 1990 EPA info

Apr. 29/16: Updated yrs of manufacture 2017-2021

Dec. 18/18: Rev. B Updated Omni logo + add info to be 2020 compliant

Jan. 14/19: Updated Report # + Ref Test

HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURNS. READ NAMEPLATE AND INSTRUCTIONS.

ATTENTION

CHAUD EN COURS DE FONCTIONNEMENT.

NE PAS TOUCHER. ÉLOIGNER LES ENFANTS, LES VÊTEMENTS ET LES MEU-

BLES DE L'APPAREIL. LE CONTACT AVEC L'APPAREIL PEUT OCCA-

SIONNER DES BRÛLURES. LIRE CETTE ÉTIQUETTE ET LES CONSIGNES.

DO NOT REMOVE THIS LABEL

431

JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC

CAUTION

DATE OF MANUFACTURE

919-337b

LISTED ROOM HEATER, SOLID FUEL TYPE, ALSO

FOR USE IN MOBILE HOME INSTALLATION

MODEL: REGENCY FREESTANDING STOVE - F3500

TESTED TO: UL-1482 -2011 (R 2015) / ULC-S627-00

WARNING: THE SPACE BENEATH THE HEATER MUST NOT BE OBSTRUCTED. OPERATE ONLY WITH FIREBRICKS IN PLACE.

FOR USE WITH SOLID WOOD FUEL ONLY. USE OF OTHER FUELS MAY DAMAGE HEATER AND CREATE A HAZARDOUS CONDITION. DO NOT OBSTRUCT COMBUSTION AIR

OPENINGS. OPERATE ONLY WITH FIREBRICKS IN PLACE. RISK OF SMOKE AND FLAME SPILLAGE, OPERATE ONLY WITH DOORS FULLY CLOSED. DO NOT USE GRATE

OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. DO NOT OVERFIRE - IF HEATER OR CHIMNEY CONNECTOR GLOWS YOU ARE OVERFIRING. INSPECT AND

CLEAN CHIMNEY AND CONNECTOR FREQUENTLY. UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. KEEP FURNISHINGS AND OTHER

COMBUSTIBLE MATERIAL AWAY FROM HEATER. REPLACE GLASS ONLY WITH NEOCERAM GLASS. COMBUSTIBLE FLOOR MUST BE PROTECTED BY NON-COMBUSTIBLE

MATERIAL EXTENDING BENEATH THE HEATER AND TO THE FRONT AND SIDES AS INDICATED OR TO THE NEAREST PERMITTED COMBUSTIBLE MATERIAL.

OPTIONAL COMPONENTS: FAN (846-515), ELECTRICAL RATING: VOLTS 115, 60 HZ, 2 AMPS., AIRMATE, OUTSIDE AIR KIT, ASH DRAWER, COMBUSTOR PART #051-530

THIS WOOD HEATER CONTAIN A CATALYTIC COMBUSTOR WHICH REQUIRES PERIODIC INSPECTION AND REPLACEMENT FOR PROPER OPERATION. IT IS AGAINST THE

LAW TO OPERATE THIS WOOD HEATER IN A MANNER INCONSISTENT WITH OPERATING INSTRUCTIONS IN INSTRUCTION MANUAL, OR IF THE CATALYTIC ELEMENT IS

DEACTIVATED OR REMOVED.

DANGER: RISK OF ELECTRIC SHOCK. DISCONNECT POWER BEFORE SERVICING UNIT. DO NOT ROUTE POWER CORD UNDER OR IN FRONT OF APPLIANCE.

CAUTION: MOVING PARTS MAY CAUSE INJURY. DO NOT OPERATE UNIT WITH FAN HOSING REMOVED.

CAUTION: HOT PARTS. DO NOT OPERATE UNIT WITH DOOR OR GLASS REMOVED.

COMPONENTS REQUIRED FOR MOBILE HOME INSTALLATION: OUTSIDE AIR KIT AND ONE OF THE FOLLOWING DOUBLE WALL CONNECTOR

IN CANADA: LISTED SECURITY MODEL DP, OR OLIVER MACLEOD PRO-VENT PV DOUBLE WALLED CONNECTOR WITH LISTED CHIMNEY SYSTEM: LISTED SECURITY MODEL

SECURITY S2100+, ICC EXCEL 2100, SIMPSON DURA-PLUS HTC, SELKIRK SENTINAL CF.

IN USA: LISTED DOUBLE WALL CONNECTORS SECURITY MODEL DP, SELKIRK MODEL DS, OLIVER MACLEOD PRO VENT PV, SIMPSON DURA VENT MODEL DVL, METAL-

FAB DOUBLE WALL. CONNECTED TO ONE OF THE FOLLOWING COMPATIBLE CHIMNEY SYSTEMS SELKIRK SURE-TEMP, PROJET Nova Temp, SECURITY SECURE TEMP

ASH+, SECURITY SECURE TEMP S-2100+, METAL-FAB TEMP/GUARD 2100, AMERI-TEC HS, ICC EXCEL 2100 . USE CHIMNEY COMPONENTS AS SPECIFIED IN INSTALLATION

INSTRUCTIONS.

AVERTISSEMENT : L’ESPACE SITUÉ SOUS L’APPAREIL DE CHAUFFAGE NE DOIT PAS ÊTRE OBSTRUÉ. FAIRE FONCTIONNER SEULEMENT LORSQUE LES BRIQUES SONT

EN PLACE.

À UTILISER SEULEMENT AVEC UN COMBUSTIBLE DE BOIS SOLIDE. L’UTILISATION D’AUTRES COMBUSTIBLES PEUT ENDOMMAGER L’APPAREIL DE CHAUFFAGE ET

PRÉSENTER UN DANGER. NE PAS OBSTRUER LES OUVERTURES DE L’AIR DE COMBUSTION. FAIRE FONCTIONNER SEULEMENT LORSQUE LES BRIQUES SONT EN

PLACE. RISQUE DE FUMÉE ET DE DÉBORDEMENT DES FLAMMES. FAIRE FONCTIONNER SEULEMENT AVEC LES PORTES COMPLÈTEMENT FERMÉES. NE PAS UTILISER

DE GRILLE NI SURÉLEVER LE FOYER. FAIRE LE FEU DIRECTEMENT SUR L’ÂTRE. NE PAS SURCHAUFFER - SI LE POÊLE OU LE CONNECTEUR DE CHEMINÉE ROUGEOIE,

IL Y A SURCHAUFFE. INSPECTER ET FAIRE RAMONER FRÉQUEMMENT LA CHEMINÉE ET LE CONNECTEUR. DANS CERTAINES CONDITIONS D’UTILISATION, UN DÉPÔT

DE CRÉOSOTE PEUT SE FORMER RAPIDEMENT. TENIR LES MEUBLES ET TOUT AUTRE MATÉRIAU COMBUSTIBLE À DISTANCE DU FEU. REMPLACER LA VITRE SEULE-

MENT PAR UNE VITRE NÉOCÉRAM. LE PLANCHER COMBUSTIBLE DOIT ÊTRE PROTÉGÉ PAR UN MATÉRIAU NON COMBUSTIBLE SE PROLONGEANT SOUS L’APPAREIL, À

L’AVANT ET SUR LES CÔTÉS, TEL QU’INDIQUÉ, OU JUSQU’AU MATÉRIAU COMBUSTIBLE LE PLUS PROCHE PERMIS.

PIÈCES EN OPTION : VENTILATEUR (846-515), ALIMENTATION ÉLECTRIQUE : VOLTS 115,60 HZ, 2 AMPS; DIFFUSEUR AIRMATE, DISPOSITIF D’AIR EXTÉRIEUR, TIROIR À

CENDRES, CATALYSEUR PIÈCE NO051-530.

CET APPAREIL AU BOIS COMPREND UN CATALYSEUR DE POSTCOMBUSTION QUI A BESOIN D’ÊTRE INSPECTÉ ET REMPLACÉ RÉGULIÈREMENT POUR UN FONCTIONNE-

MENT ADÉQUAT. LA RÉGLEMENTATION INTERDIT DE FAIRE FONCTIONNER CET APPAREIL DE CHAUFFAGE AU BOIS SI LES CONSIGNES D’UTILISATION CONTENUES

DANS LE PRÉSENT MANUEL NE SONT PAS RESPECTÉES OU SI L’ÉLÉMENT CATALYTIQUE EST DÉSACTIVÉ OU RETIRÉ.

DANGER : RISQUE D’ÉLECTROCUTION. DÉBRANCHER L’ALIMENTATION ÉLECTRIQUE AVANT L’ENTRETIEN DE L’APPAREIL. NE PAS PLACER LE CORDON

D’ALIMENTATION ÉLECTRIQUE AU-DESSOUS OU DEVANT L’APPAREIL.

ATTENTION : LE DÉPLACEMENT DES PIÈCES PEUT CAUSER DES BLESSURES. NE PAS FAIRE FONCTIONNER L’APPAREIL SANS LE VENTILATEUR.

ATTENTION : PIÈCES CHAUDES, NE PAS FAIRE FONCTIONNER L’APPAREIL SANS LA PORTE OU LA VITRE.

COMPOSANTS REQUIS POUR UNE INSTALLATION DANS UNE MAISON MOBILE : DISPOSITIF D’AIR EXTÉRIEUR ET UN DES CONNECTEURS À DOUBLE PAROI SUIVANTS.

AU CANADA : CONNECTEUR À DOUBLE PAROI HOMOLOGUÉ MODÈLES SECURITY DP, OU OLIVER MACLEOD PRO-VENT PV AVEC SYSTÈME DE CHEMINÉE HOMOLOGUÉ

: MODÈLE DE SÉCURITÉ HOMOLOGUÉ SECURITY S2100+, ICC EXCEL 2100, SIMPSON DURA-PLUS HTC, SELKIRK SENTINAL CF.

AUX ÉTATS-UNIS : CONNECTEURS À DOUBLE PAROI HOMOLOGUÉS MODÈLES SECURITY DP, SELKIRK DS, OLIVER MCLEOD PRO VENT PV, SIMPSON DURANT VENT

DVL, METAL FAB. RELIÉS À L’UN DES SYSTÈMES DE CHEMINÉE COMPATIBLES SUIVANTS : SELKIRK SURE-TEMP, PROJET NOVA TEMP, SECURITY SECURE TEMP ASH+,

SECURITY SECURE TEMP S-2100+, METAL-FAB TEMP/GUARD 2100, AMERI-TECH HS, ICC EXCEL 2100. UTILISER LES PIÈCES DE CHEMINÉE COMME SPÉCIFIÉ DANS LES

CONSIGNES D’INSTALLATION.

FLOOR

PROTECTION*

INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. CONTACT LOCAL BUILDING

OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA. USE 6"(152MM) DIAMETER MINIMUM 24 MSG BLACK

OR 26 MSG BLUED STEEL CONNECTOR WITH LISTED UL103 HT or ULCS629 FACTORY-BUILT CHIMNEY SUITABLE FOR USE WITH SOLID FUELS OR

MASONRY CHIMNEY.

SEE LOCAL BUILDING CODE AND MANUFACTURER'S INSTRUCTIONS FOR PRECAUTIONS REQUIRED FOR PASSING A CHIMNEY THROUGH A COMBUSTIBLE

WALL OR CEILING. DO NOT PASS CHIMNEY CONNECTOR THROUGH COMBUSTIBLE WALL OR CEILING. DO NOT CONNECT THIS UNIT TO A CHIMNEY

FLUE SERVING ANOTHER APPLIANCE.

CAUTION:

BURNING OF MATERIAL OTHER THAN THE SPECIFIED FUELS MAY MAKE THE CATALYST IN THE COMBUSTOR INACTIVE. THE COMBUS-

TOR IS FRAGILE, HANDLE CAREFULLY.

THE PERFORMANCE OF THE CATALYTIC DEVICE OR ITS' DURABILITY HAS NOT BEEN EVALUATED AS PART OF THE CERTIFICATION.

INSTALLER ET UTILISER SEULEMENT SELON LES INSTRUCTIONS D’INSTALLATION ET D’UTILISATION DU FABRICANT.

CONTACTER LES RESPONSABLES DU BÂTIMENT OU DU SERVICE-INCENDIE DE VOTRE RÉGION POUR CONNAÎTRE LES RESTRICTIONS ET EXI-

GENCES D’INSPECTION DANS VOTRE RÉGION. UTILISER UN CONNECTEUR D’UN DIAMÈTRE MINIMAL DE 152 MM (6 PO) 24 MSG EN ACIER NOIR OU

26 MSG EN ACIER BRONZÉ AVEC CHEMINÉE PRÉFABRIQUÉE HOMOLOGUÉE CONÇUE POUR UTILISATION AVEC COMBUSTIBLES SOLIDES OU UNE

CHEMINÉE DE MAÇONNERIE.

VOIR LE CODE DU BÂTIMENT LOCAL ET LES INSTRUCTIONS DU FABRICANT CONCERNANT LES PRÉCAUTIONS EXIGÉES POUR INSTALLER UNE

CHEMINÉE TRAVERSANT UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES. NE FAITES PAS TRAVERSER LE CONNECTEUR DE CHEMINÉE

DANS UN MUR OU PLAFOND EN MATÉRIAUX COMBUSTIBLES. NE RACCORDEZ PAS CE POÊLE À BOIS À UN CONDUIT DE CHEMINÉE DESSERVANT

UN AUTRE APPAREIL.

CERTIFICATION DU MAISON MOBILE, APPAREIL DE CHAUFFAGE AMBIANT HOMOLOGUÉ À COMBUSTIBLE SOLIDE, CONVENANT AUSSI POUR

INSTALLATION DANS UNE MAISON MOBILE.

In USA:

V 203 mm / 8"

W 406 mm / 16"

X 838 mm / 33"

Y 1181 mm / 46-1/2"

Z 203 mm / 8"

In Canada:

V 203 mm / 8"

W 450 mm / 18"

X 838 mm / 33"

Y 1232 mm / 48-1/2"

Z 203 mm / 8"

20182017 2020 20212019

431

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS

INSTALLATION USING 6" SINGLE WALL OR LISTED

DOUBLE WALL

CONNECTOR ONLY: RESIDENTIAL, ALCOVE, MOBILE

HOME

To Top of stove:

A) 279mm / 11"

To Flue Centre Line:

E) 406mm / 16"

To Rear Shield:

B) 241mm / 9.5"

To Flue Centre Line:

F) 521mm / 20-1/2"

To Corner of Stove:

C) 203mm / 8"

Alcove width:

G) 1524mm / 60"

To Flue Centre Line:

D) 610mm / 24"

To Top of Flue:

H) 152mm / 6"

MANUFACTURED BY:

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD.

6988 VENTURE ST.

DELTA, BC V4G 1H4

MADE IN CANADA

MINIMUM PARALLEL / ALCOVE CEILING HEIGHT: 2.1 M / 83" MAXIMUM ALCOVE DEPTH 1219 MM / 48 IN.

HAUTEUR MINIMALE DU PLAFOND DE L’ALCÔVE : 2,1 M / 83PO. PROFONDEUR MAXIMALE DE L’ALCÔVE : 1219 MM / 48 PO.

0219WS018S

U.S. ENVIRONMENTAL PROTECTION AGENCY CERTIFIED TO COMPLY WITH 2020 PARTICULATE EMISSION STANDARDS USING

CORD WOOD.” TESTED TO ASTM E3053. MODEL REGENCY F3500 – 0.9G /HR. THIS WOOD HEATER NEEDS PERIODIC INSPEC-

TION AND REPAIR FOR PROPER OPERATION. CONSULT THE OWNER'S MANUAL FOR FURTHER INFORMATION. IT IS AGAINST

FEDERAL REGULATIONS TO OPERATE THIS WOOD HEATER IN A MANNER INCONSISTENT WITH THE OPERATING INSTRUCTIONS

IN THE OWNER'S MANUAL.

CERTIFIÉ CONFORME AUX NORMES 2020 DU U.S. ENVIRONMENTAL PROTECTION AGENCY EN MATIÈRE D'ÉMISSION DE

PARTICULES DE BOIS AVEC DU BOIS DE CORDE''. APPROUVÉ ASTM E3053. MODÈLE REGENCY F3500 – 0,9 G /H. CET AP-

PAREIL DE CHAUFFAGE AU BOIS DOIT ÊTRE INSPECTÉ PÉRIODIQUEMENT ET RÉPARÉ POUR FONCTIONNER CORRECTEMENT.

CONSULTER LE MANUEL D’INSTALLATION POUR PLUS D’INFORMATION. LA RÉGLEMENTATION FÉDÉRALE INTERDIT DE FAIRE

FONCTIONNER UN TEL APPAREIL SI LES CONSIGNES D'UTILISATION CONTENUES DANS LE PRÉSENT MANUEL NE SONT PAS

RESPECTÉES.

SAFETY LABEL FOR F3500

F3500 Regency Freestanding Woodstove

DIMENSIONS

dimensions

UNIT DIMENSIONS

12-7/8"

23"

26"

8-7/8"

15-1/16"

36"

32-7/8"

24-7/16"

30-1/4"

22"

[225mm]

[660mm]

[584mm]

[559mm]

[621mm]

[768mm]

[914mm]

[865mm]

6" Flue Collar

ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.

ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

Shown with optional fan

F3500 Regency Freestanding Woodstove

DIMENSIONS

dimensions

WOOD STOVE OUTSIDE AIR DIMENSIONS

With pedestal from base of unit to centerline

5-1/2" (138mm)

Rear

F3500 Regency Freestanding Woodstove

installation

RESIDENTIAL

INSTALLATION

1) Please read this entire manual before you install

and use your new woodstove. Failure to follow

instructions may result in property damage,

bodily injury or even death. Be aware that local

Codes and Regulations may override some

items in this manual. Check with your local

inspector.

2) Select a position for your Regency Stove. Consult

the minimum clearance chart for your model

and set the stove in place.

3) To insure vertical alignment, suspend a plumb

bob from the ceiling over the exact center of

your stove ﬂue and mark a spot on the ceiling

to indicate the center of the chimney.

4) Check that the area above the ceiling is clear

for cutting. Re-conﬁrm the clearance from the

stove to combustibles to insure that they are

within the prescribed limits.

5) This woodstove must be connected to a UL

103 HT (ULC S629) listed chimney or a code

approved masonry chimney with a ﬂue liner.

Space heater is to be connected to a factory

built chimney conforming to CAN/ULC-5629

standard for 650C factory built chimneys. The

chimney requirement is 6", refer to appropri-

ate sections in this manual for speciﬁcs.

6) Install chimney according to chimney manu-

facturers instructions. The performance of your

woodstove is governed to a very large part by

the chimney system. Too short a chimney can

cause difﬁcult start-up, dirty glass, back smok-

ing when door is open, and even reduced heat

output.

Too tall a chimney may prompt excessive draft

which can result in very short burn times and

excessive heat output. The use of an inexpen-

sive ﬂue pipe damper may be helpful in reducing

excessive draft.

CAUTION: The chimney should be the same

size as the 6" ﬂue outlet on the stove. The

chimney must be listed as suitable for use with

solid fuels. For other types of chimneys check

with your local building code ofﬁcials. Do not

confuse a chimney with a type “B” Venting

System used for gas appliances as suitable for

a wood burning appliance. For Mobile Home

installations refer to that section within this

manual.

7) Mark the location of the pedestal base or legs

on the ﬂoor, then move the stove aside and

mark the position of the ﬂoor protector.

8) The ﬂoor protector must be of non-combustible

material and must extend 16" (406mm) in front

of the door opening and 8" (203mm) to the

sides and rear of the unit. Some areas may

require a larger size ﬂoor protector. See your

local inspector. For outside air installation refer

to Mobile Home installation instructions within

this manual.

9) When the ﬂoor protection is complete, position

the stove with the ﬂue collar centered under the

installed chimney.

10) In areas with frequent seismic activity, Regency

recommends that your unit is secured to the

ﬂoor by using the bolt down holes inside the

pedestal (the same ones used in Mobile Home

installations).

11) For residential installations 6" (single wall OK)

double wall chimney, the chimney connector

must be at least 24 gauge steel. Do not use

galvanized pipe. For Mobile Home installation

refer to the Mobile Home installation instructions

within this manual.

12) DO NOT CONNECT THIS UNIT TO A CHIM-

NEY SERVING ANOTHER APPLIANCE.

13) A chimney connector cannot pass through an

attic or roof space, closet or similar concealed

space, or a ﬂoor, ceiling, wall or partition of

combustible construction. In Canada, if pas-

sage through a wall, or partition of combustible

construction is desired, the installation shall

conform to CAN/CSA-B365, Installation Code

for Solid-Fuel-Burning Appliances and Equip-

ment.

14) Your Regency Woodstove is not to be connected

to any air distribution duct.

Emissions from burning wood or gas

could contain chemicals known to the

State of California to cause cancer, birth

defects or other reproductive harm.

CAUTION:

Do not alter or makeshift chimney or install.

Install as per Manual.

NOTE: In Canada, ﬂoor protection must

extend 18" (450mm) to the front and

8" (203mm) to each side and back

of the stove.

MODULAR INSTALLATION OPTIONS

WARNING: ONLY USE SPECIFIED COMPONENTS.

The following items are required when assembling your Regency Stove. F3500 unit - the Rear Heat Deﬂector is supplied with the stove, but if you choose

not to use it you must use the Airmate instead.

Modular Part

See the Minimum Clearance to Combustible Materials chart in the Installation section of this manual

F3500

Airmate OR

Rear Heat Deﬂector

Convection heat with Airmate vs. Radiant Heat with Rear Heat Deﬂector. The Airmate pushes heat forward out into

the room, the Rear Heat Deﬂector deﬂects the heat upward. Refer to the Installation sections within this manual.

OPTIONS: These can be installed at time of installation or added later:

Blower/Fan

Adding the blower will increase the area heated by the stove, it can move warm air beyond the room where the stove

Ash Drawer Kit

Adding the Ash Drawer Kit makes cleaning ashes out of the stove easier and cleaner (refer to Bottom Shield Ash

Drawer Kit, Installation section).

Airmate

The Airmate pushes heat forward out into the room.

Outside Air Kit

Draw combustion air from the outside of dwelling.

ROOM AIR - IMPORTANT

For installation using room air for combustion,

remove knockout from the pedestal.

Mobile home installations require the use of

outside air.

Fresh air is important - if heater is starved for air

caused by exhaust fans or icing, the unit will not

operate properly.

On pedestal units there are two locations where

outside air may be adapted to the unit. If using

the bottom of the pedestal, do not remove knock-

out from the rear of the pedestal. Only remove

rear knockout if outside air will be brought in from

the rear.

Note: Once the knockout is removed there are

two tabs remaining. Bend both tabs out

for ease of installation of outside air kit.

F3500 Regency Freestanding Woodstove

installation

Side View

Rear Heat Deflector

Screws

Diagram 2

Diagram 3

STOVE ASSEMBLY

PRIOR TO

INSTALLATION

The F3500 unit requires the pedestal attached

to the base. The F3500 stove requires either the

Airmate or Rear Heat Deﬂector on top of the stove.

Clearances to combustible materials vary depend-

ing on whether the Airmate or rear heat deﬂector

is installed, so be sure to check the Minimum

Clearances, Installation section.

Airmate Assembly for F3500

1) The Airmate sits on top of the stove with the slots

in the sides ﬁtting over the curved deﬂector on

the rear stove top. See diagram 1. Discard the

Rear Heat Deﬂector that is supplied with the

unit, it is not required if the Airmate is installed.

2) Center the Airmate and push it forward to the

front of the stove. The back of the Airmate

should be level with the back and sides of the

rear heat shield. See Diagrams 2 & 3.

Rear Heat Deﬂector

Assembly for F3500

The rear heat deﬂector is supplied with the stove

and must be installed unless the optional Airmate

has been selected. It stops the heat radiated from

the ﬂue collar from overheating the rear wall. The

rear heat deﬂector is installed on top of the rear

heat shield, as shown in Diagram 4.

Side Shield Adjustment

The left and right side shields are lowered for ship-

ping and handling. It allows for a handhold on the

top of the stove. Before placing in the Step Stove

in its ﬁnal position, the side shields must be raised.

Loosen the screws on the rear on the stove (3 per

side), slide the side panel up as far as possible and

then secure by tightening the screws.

1) Push the

Regency logo

into the two

holes in the

front bottom left

corner of the

pedestal cover

plate.

Note: Any paint touch up should be done prior

to placing logo on pedestal.

2) If not using ash drawer, then cover plate must be

installed.

Airmate

Rear Heat

Shield

Side

Shield

Stove

Diagram 1

Diagram 4

Logo Installation

F3500 Regency Freestanding Woodstove

installation

MINIMUM CLEARANCE TO COMBUSTIBLE MATERIALS

Please read the section below carefully as clearances depend on whether the Airmate or the Rear Heat Deﬂector is installed on the stove.

Measurements "From Unit" are from the top plate of the stove to a side wall or to a corner, and from the rear heat shield to a back wall.

Clearances may only be reduced by means approved by the regulatory authority.

Note: Minimum ceiling height - 83" (2108mm)

NOTE: Be aware that local Codes and

Regulations may override some

clearances listed in this manual.

Check with your local inspector.

Residential Close Clearance (To be installed with required pipe components) Listed Double Wall Pipe

When the stove is installed as a close clearance residential unit, a listed double wall connector is required from the stove collar to the ceiling level.

F3500 with Airmate or

Rear Deﬂector

A B C D E F

11"

279mm

9-1/2"

241mm

203mm

24"

610mm

16"

406mm

20-1/2"

521mm

Residential Installation "C" Vent (Single Wall Pipe)

F3500 with Airmate or

Rear Deﬂector

A B C D E F

11"

279mm

9-1/2"

241mm

203mm

24"

610mm

16"

406mm

20-1/2"

521mm

Mobile Home Close Clearance (To be installed with required pipe components) Listed Double Wall Pipe When

the stove is installed as a close clearance residential unit, a listed double wall connector is required from the stove collar to the ceiling level.

Refer to Mobile Home Installation in this manual.

F3500 with Airmate or

Rear Deﬂector

A B C D E F

11"

279mm

9-1/2"

241mm

203mm

24"

610mm

16"

406mm

20-1/2"

521mm

Minimum Alcove Clearance to Combustible Materials

The Regency Freestanding models have been alcove approved and must be installed

with a listed double wall connector to the ceiling level.

Note: Minimum alcove ceiling height - 83" (2108 mm) Vertical Termination}

H = Maximum depth of alcove - 48" (1219mm)

G= Minimum width of alcove - 60" (1524mm)

ROOF EXIT

WALL EXIT

ROOF EXIT

WALL EXIT

ROOF EXIT

WALL EXIT

NOTE: Clearances to combustibles are for

the safety of the property. To avoid

overheating and damaging the

appliance these clearances should

be maintained for non-combustibles

also.

NOTE: This clearance is also required for air space between the appliance and wall/ceiling.

F3500 Regency Freestanding Woodstove

installation

FLOOR PROTECTION (Ember Protection

Only Required)

A combustible ﬂoor must be protected by non-combustible

material (like tile, concrete board, or certiﬁed to UL-1618 or

as deﬁned by local codes) extending beneath the heater and

a minimum of 8" (203mm) from each side and minimum 16"

(406mm) from the front face of the stove and minimum 6"

(or the rear clearance to combustibles whichever is smaller)

from the rear of the stove.

NOTE: This clearance is also required for air space between

the appliance and wall/ceiling. Where the appliance is installed

less than 8" from a rear wall, the ember pad only needs to

extend to the base of the wall based on the clearances noted

in this manual.

When installed with horizontal venting, non-combustible ﬂoor

protection must beneath the ﬂue pipe and extend 2" (51mm)

beyond each side.

Minimum Overall Width (X) of Floor

Protector for all installations:

Stove F3500 33" (838mm)

NOTE: In Canada, ﬂoor protection must extend 18" (450mm) to the front

and 8" (203mm) to each side and back of the stove.

Minimum Overall Depth (Y) of Floor Protector

Unit Residential

Close Clearance

Mobile Home

Close Clearance

Alcove

F3500

Y Z

USA

46-1/2" 8" 46-1/2 8" 46-1/2 8"

Canada

48-1/2" 8" 48-1/2" 8" 48-1/2" 8"

The rear clearance to combustibles is less than 6" (for corner installations the rear corners may

be angled to take advantage of the closer clearances.

NOTE: USA clearances shown above.

Minimum Overall Depth (Y) of Floor Protector - Corner Hearth

Reference only when hearth pad is installed to rear wall at minimum pipe clearances.

Hearth Depth

F3500 L M N O

Residential Installation ''C'' Vent (Single Wall)

Canada 33" (838mm) 65" (1651mm) 57-9/16" (1461mm) 25-3/4" (654mm)

USA 33" (838mm) 63" (1600mm) 56-1/8" (1425mm) 24-5/16" (618mm)

Residential Close Clearance (To be installed with required pipe components)

Canada 33" (838mm) 65" (1651mm) 57-9/16" (1461mm) 25-3/4" (654mm)

USA 33" (838mm) 63" (1600mm) 56-1/8" (1425mm) 24-5/16" (618mm)

F3500 Regency Freestanding Woodstove

installation

MASONRY FIREPLACE

There are listed kits available to connect a stove to a masonry

ﬁreplace. The kit is an adapter that is installed at the location

of the ﬁreplace damper. The existing damper may have to

be removed to allow installation.

Minimum vertical of 36" before any offset.

Horizontal Maximum of 36" with 1/4" rise per foot.

NOTE: Recommend using 2-45º instead of 90º to improve

draft and performance.

Max. 36"

Horizontal

Min. 36"

Vertical

Rise

[152mm]

10"

[254mm]

18"

[457mm]

Single

Double

NOTE: Only a 6" and or 5.5" liner may be used when relin-

ing the masonry chimney. Do not increase/decrease size

of the liner as this could result in poor performance, over

ﬁring and or dangerous operating conditions which may

void your warranty.

Do not use or add a pipe damper as this will result in poor

performance, over ﬁring and or dangerous operating condi-

tions which may void your warranty. This appliance already

has a bypass damper in place.

A minimum vertical rise of 36 inches is required from top of

stove collar prior to having any offset. It is recommended

that 45º elbows be used instead of a 90º elbow to improve

draft and performance. If not adhered to this, it will result

in poor performance overfiring and or dangerous operating

conditions which may void your warranty.

WALL EXIT CLEARANCE FACTORY BUILT CHIMNEY

When a metal prefabricated chimney is used, the manufacturer's installation instructions must be followed. You must also purchase and install the ceiling

support package or wall pass-through and "T" section package, ﬁrestops (where needed), insulation shield, roof ﬂashing, chimney cap, etc. Maintain proper

clearance to the structure as recommended by the manufacturer. The chimney must be the required height above the roof or other obstructions for safety and

proper draft operation.

Minimum vertical of 36" before any offset.

Horizontal Maximum of 36" with 1/4" rise per foot.

NOTE: Recommend using 2-45º instead of 90º to improve draft

and performance.

Note: Minimum ceiling height roof - 83" (2108mm)

[152mm]

[127mm]

Max. 36"

Horizontal

Min. 36"

Vertical

Rise

18"

[457mm]

Listed Double Wall

Single Wall

F3500 Regency Freestanding Woodstove

installation

Method A: 12" (304.8 mm) Clearance to Combustible Wall Member:

Using a minimum thickness 3.5" (89 mm) brick and a 5/8" (15.9 mm)

minimum wall thickness clay liner, construct a wall pass-through.

The clay liner must conform to ASTM C315 (Standard Speciﬁcation

for Clay Fire Linings) or its equivalent. Keep a minimum of 12" (304.8

mm) of brick masonry between the clay liner and wall combustibles.

The clay liner shall run from the brick masonry outer surface to the

inner surface of the chimney ﬂue liner but not past the inner surface.

Firmly grout or cement the clay liner in place to the chimney ﬂue liner.

Method B: 9" (228.6 mm) Clearance to Combustible Wall Member:

Using a 6" (152.4 mm) inside diameter, listed, factory-built Solid-Pak

chimney section with insulation of 1" (25.4 mm) or more, build a wall

pass-through with a minimum 9" (228.6 mm) air space between the

outer wall of the chimney length and wall combustibles. Use sheet metal

supports fastened securely to wall surfaces on all sides, to maintain the

9" (228.6 mm) air space. When fastening supports to chimney length,

do not penetrate the chimney liner (the inside wall of the Solid-Pak

chimney). The inner end of the Solid-Pak chimney section shall be

ﬂush with the inside of the masonry chimney ﬂue, and sealed with a

non-water soluble refractory cement. Use this cement to also seal to

the brick masonry penetration.

Method C: 6" (152.4 mm) Clearance to Combustible Wall Member:

Minimum

12 in. (304.8mm)

to combustibles

Masonry chimney

Chimney Flue

Minimum chimney clearance to brick

and combustibles 2 in. (50.8mm)

Minimum clearance

12 in. (304.8mm)

of brick

Chimney

connector

Fire clay

liner

Starting with a minimum 24 gage (.024" [.61 mm]) 6" (152.4 mm) metal

chimney connector, and a minimum 24 gage ventilated wall thimble

which has two air channels of 1" (25.4 mm) each, construct a wall

pass-through. There shall be a minimum 6" (152.4) mm separation

area containing ﬁberglass insulation, from the outer surface of the wall

thimble to wall combustibles. Support the wall thimble, and cover its

opening with a 24-gage minimum sheet metal support. Maintain the

6" (152.4 mm) space. There should also be a support sized to ﬁt and

hold the metal chimney connector. See that the supports are fastened

securely to wall surfaces on all sides. Make sure fasteners used to

secure the metal chimney connector do not penetrate chimney ﬂue liner.

Method D: 2" (50.8 mm) Clearance to Combustible Wall Member:

Start with a solid-pak listed factory built chimney section at least

12" (304 mm) long, with insulation of 1" (25.4 mm) or more, and an

inside diameter of 6" (2 inches [51 mm] larger than the 6" [152.4

mm] chimney connector). Use this as a pass-through for a minimum

24-gage single wall steel chimney connector. Keep solid-pak section

concentric with and spaced 1" (25.4 mm) off the chimney connector

by way of sheet metal support plates at both ends of chimney section.

Cover opening with and support chimney section on both sides with

24 gage minimum sheet metal supports. See that the supports are

fastened securely to wall surfaces on all sides. Make sure fasteners

used to secure chimney ﬂue liner.

COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS

F3500 Regency Freestanding Woodstove

installation

Horizontal Installation

Standard Ceiling Installation

8. To complete your chimney installation, install

the single wall or double wall connector pipe

from the stove’s ﬂue collar to the chimney

support device.

NOTE: When attaching the chimney to the appli-

ance, ensure a minimum of two (2) screws are

used to establish a snug ﬁt.

9. If you are using a horizontal connector, the

chimney connector should be as high as pos-

sible while still maintaining the 18" (457mm)

minimum distance from the horizontal con-

nector to the ceiling.

10. NOTE: Residential Close Clearance and

Alcove installations require a listed double

wall connector from the stove collar to the

ceiling level.

The diagrams below illustrate one way to install

your unit into a standard ceiling or with a horizontal

connector. Check with your dealer or installer for

information on other options available to you.

STEP-BY-STEP

CHIMNEY AND

CONNECTOR

INSTALLATION

Note: These are a generic set of chimney

installation instructions. Always follow

the manufacturers own instructions

explicitly. Verify the Minimum Recom-

mended Heights for Woodstove Flue

(Table 1 in the Installation section).

1. With your location already established, cut

and frame the roof hole. It is recommended

that no ceiling support member be cut for

chimney and support box installation. If it is

necessary to cut them, the members must be

made structurally sound.

2. Install radiant shield and support from above.

3. Stack the insulated pipe onto your ﬁnish sup-

port to a minimum height of 3 feet above the

roof penetration, or 2 feet above any point

within 10 feet measured horizontally. There

must be at least 3 feet of chimney above the

roof level.

NOTE: Ensure each section of chimney is posi-

tively attached and secured.

Note: Increasing the chimney height above

this minimum level will sometimes

help your unit to “breathe” better by

allowing a greater draft to be cre-

ated. This greater draft can decrease

problems such as, difﬁcult start-ups,

back-smoking when door is open, and

dirty glass. It might be sufﬁcient to

initially try with the minimum required

height, and then if problems do arise

add additional height at a later date.

4. Slide the roof ﬂashing over your chimney

and seal the ﬂashing to the roof with rooﬁng

compound. Secure the ﬂashing to your roof

with nails or screws.

5. Place the storm collar over the ﬂashing, seal-

ing the joints with a silicone caulking.

6. Fasten the raincap with spark screens (if

required) to the top of your chimney.

7. For optimum efﬁciency when installing into

a masonry chimney, size accordingly, i.e.

the 6" (152.4mm) ﬂue dia. is 28.28 sq.in.

(718.31mm

F3500 Regency Freestanding Woodstove

installation

RECOMMENDED HEIGHTS FOR WOODSTOVE FLUE

Simple rules on draft (refer to Table 1).

1) At sea level minimum height is 12' straight.

2) Add the following vertical height to compen-

sate for:

45 deg. elbow = 1 ft.

90 deg. elbow = 2 ft.

"T" = 3 ft.

Each foot of horizontal run = 2 ft.

3) Add 4% overall for each 1000' above sea level.

Example: a)

1-1/2 ft. of horizontal run = 3 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 6 ft.

Example: b)

One 90 deg. elbow = 2 ft.

2 ft. of horizontal run = 4 ft.

one "T" = 3 ft.

Total Addition (at sea level) = 9 ft.

Recommended Flue Height

Elevation Example a) Example b)

0' 18' 21'

1000' 18.72' 21.84'

2000' 19.44' 22.68'

5000' 21.60' 25.20'

8000' 23.76' 27.72'

MINIMUM RECOMMENDED FLUE HEIGHTS IN FEET

(Measured from the top of the unit)

ELEVATION (FT)

ABOVE SEA

LEVEL

NUMBER OF ELBOWS

For listed double wall pipe.

0 2 x 15

2 x 30

2 x 45

0-1000 12.0 13.0 15.0 16.0

1000-2000 12.5 13.5 15.5 16.5

2000-3000 13.0 14.0 16.0 17.0

3000-4000 13.5 14.5 17.0 18.0

4000-5000 14.0 15.0 17.5 18.5

5000-6000 14.5 15.5 18.0 19.0

6000-7000 15.0 16.0 18.5 20.0

7000-8000 15.5 16.5 19.0 20.5

8000-9000 16.0 17.0 20.0 21.0

9000-10000 16.5 17.5 20.5 22.0

NOTE: No more than one offsets (two elbows) allowed. Two 45

elbows

equal one 90

elbow.

Table 1

F3500 Regency Freestanding Woodstove

installation

Pedestal

Bolted to

Floor

Permanent Outside

Air Inlet

MOBILE HOME INSTALLATION

Once you have properly marked the position of

your unit and the ﬂoor protection as outlined in

the Residential Installation items #1 through #8, a

supply of fresh air has to be supplied to your unit.

See Optional Outside Air Kit instructions in this

manual.

Place your unit in position and secure it to the ﬂoor

using two lag bolts 3/8" (10mm) x 3-1/2" (89mm)

through the two holes inside the pedestal base.

It is important to maintain the structural integrity

of the Mobile Home ﬂoor, walls and roof when

installing your unit.

For Mobile Home units installed in the U.S. the unit

must be grounded using a #8 ground wire with

approved termination and star washer.

In addition to standard installation instructions

the following requirements are mandatory for

installation in a mobile home.

1. The stove must be permanently bolted to

the ﬂoor of the Mobile Home using the ﬂoor

screws provided.

2. The stove must have a permanent outside

air source for combustion.

3. The stove must be electrically grounded to

the steel chassis of the Mobile Home.

4. A listed double-wall connector chimney

system, roof thimble, spark arrestor and roof

ﬂashing kit suitable for use in Mobile Homes

must be used.

5. If the chimney exits the Mobile Home at a

location other than through the roof, and

exits at a point 7ft. (2130mm) or less above

the ground level on which the Mobile Home

is positioned a guard or method of enclosing

the chimney shall be ﬁtted at the point of exit

for a height up to 7ft. (2130mm).

6. The chimney shall be attached directly to the

room heater and shall extend at least 3 ft.

(914mm) above the part of the roof through

which it passes. The top of the chimney should

project at least 2ft. (610mm) above the high-

est elevation of any part of the Mobile Home

within 10 ft. (3048mm) of the chimney.

7. The chimney system shall comply with Local

Requirements.

8. Any openings in a chimney guard where

required must not permit the entrance of 3/4"

(19mm) diameter rod.

9. CAUTION: THE STRUCTURAL INTEGRITY

OF THE MOBILE HOME ROOF, FLOOR,

WALLS AND CEILING MUST BE MAIN-

TAINED.

10. Check any other local building code as other

local codes may apply.

11. WARNING: DO NOT INSTALL IN A SLEEP-

ING ROOM OF A MOBILE HOME.

12. Use silicone to create an effective vapour

barrier at the location where the chimney or

other component penetrates to the exterior

of the structure.

CAUTION: At no time use unlabelled

parts, or substitute parts made for another

chimney system.

Install as per chimney manufacturer's

installation instructions.

For Canadian Installations: see Outside Air

Kit Blanking Plate - Part # 042-909

There are further requirements when installing

this unit into a mobile home in Canada Only.

WARNING: Operate only with door fully

closed - open feed door to feed ﬁre only.

1. Identify the position of the outside air damper by the orientation of the metal handle that rests outside

the galvanized pipe. The metal handle and the damper disc are in line with each other. This means

that if the metal handle is in a horizontal position, the damper is ﬂat and fully open.

2. Open the damper fully whenever you start a ﬁre. This will allow the outside air to be drawn in the

pedestal base eliminating any potential smoke escaping the stove and entering the room. (Negative

air pressure)

F3500 Regency Freestanding Woodstove

installation

The Outside Air Kit is an option for Freestanding Stoves. Outside air for combustion can be brought in either through the bottom of the pedestal or through

the rear plate of the pedestal.

Rear View

Completed Install

Side View

Outside Air Through Pedestal Bottom

Mark the position of your unit as outlined in the "General Information"

and "Clearances to Combustibles" section of the manual. Pipe fresh

air into the pedestal area by using a minimum 4" duct pipe with a

mesh grill at the outside termination.

Outside Air Through Pedestal Rear

Remove the blanking plate from the rear of the pedestal and bend

the two tabs out 90 degrees. Pipe fresh air into the pedestal area

by using a minimum 4" metallic duct pipe with a mesh grill at the

outside termination.

Fasten the pipe to the cover plate using the tabs and 2 screws.

Damper Installation

NOTE: The damper cannot be installed if attaching outside air to the

bottom of the appliance.

Supplied damper allows the combustion air to be closed off when unit

is not in operation.

Install the damper within the round pipe in an easily accessible location.

1. Drill a 5/16" hole in the desired location.

2. Insert damper with threaded section out.

3. Install damper handle and secure with wing nut.

Wing nut

Damper handle

Damper

OPTIONAL OUTSIDE AIR KIT

F3500 Regency Freestanding Woodstove

installation

LISTED COMPONENTS

FOR MOBILE HOME

INSTALLATION

The Regency F3500B Freestanding pedestal

units are approved for installation in a Mobile

Home if one of the following pipe systems is used.

U.S. Installation*

METALBESTOS SSII

Qty. Part # Description

1 6DS-VK Connector Kit

1 6TMH Shield/Support

1 6TAF-6 Flashing

1 6T-36 Chimney Length

1 6T-18 Chimney Length

1 6T-CT Rain Cap

PRO-JET 3103

Qty.Part # Description

1 PV06-TK Connector

1 CSB Shield/Support

1 RRS Radiation Shield

1 LFR03 Flashing

1 SL3 Chimney Length

1 SL1 Chimney Length

1 RCSA Rain Cap

SECURITY ASHT

Qty.Part # Description

1 DL42A-6 Connector Kit

1 6SS Shield/Support

1 6FAMH Flashing

1 6L3 Chimney Length

1 6L1 Chimney Length

1 CPE Rain Cap

SECURITY S2100

Qty.Part # Description

1 DL42A-6 Connector Kit

1 6XSF Support

1 6XFA Flashing

1 6XL3 Chimney Length

1 6XL18 Chimney Length

1 6XCPE Rain Cap

METAL-FAB TEMP/GUARD 2100

Qty.Part # Description

1 6DWBK Connector

1 6TGRS Roof Support

1 6TGG36 Chimney Length

1 6TGG12 Chimney Length

1 6TGF Flashing

1 6TGC Rain Cap

AMERI-TEC HS

Qty.Part # Description

1 6DCC Connector

1 6HSRS-12 Roof Support

(6PLRS-12-BK)

1 6F Flashing

1 6HS-36 Chimney Length

1 6HS-18 Chimney Length

1 6HS-RCS Rain Cap (6PL-MPC)

SIMPSON DURA-PLUS

Qty.Part # Description

1 6DVL8693 Connector Kit

1 6DP-MH9096 Mobile Home Kit

ICC EXCEL 2100

Qty.Part # Description

1 6CL48 48" Chimney length (also in

12", 18", 24" lengths.

1 6RC Rain Cap

1 6RCS Spark Screen (for rain cap)

1 6RDS/SQS Round/Square support box

1 6VF Flashing

1 6UBA "Ultrablack" Close Clearance

Connector

Canadian Installations*

SECURITY S2100

ICC EXCEL 2100

SELKIRK SENTINAL CF

*The use of alternate pitch ﬂashings, support

box extensions, additional chimney lengths, and

additional chimney bracing, may be used on each

of the previously listed systems. These parts

though must be from the same system as listed,

and must be a similar and/or complimentary part.

CAUTION: At no time use unlabelled

parts, or substitute parts made for

another chimney system.

Install as per chimney manufacturer's instal-

lation instructions.

F3500 Regency Freestanding Woodstove

installation

STAINLESS STEEL SMOKE DEFLECTOR INSTALLATION / REPLACEMENT

1. The stainless smoke deﬂector is located in the upper front area of the ﬁre-

box (see diagram below). The deﬂector is held in place with 2 x 7/16” hex

head bolts. Prior to the ﬁrst ﬁre, ensure deﬂector is seated properly and

secured with 2 hand tightened bolts.

2. To replace the deﬂector, loosen off both 7/16” bolts and slide deﬂector up-

ward and out. Install new deﬂector and hand tighten 7/16” hex head bolts.

Ensure positive location of the deﬂector prior to hand tightening.

WARNING: Operation of the unit without proper installation of smoke

deﬂector will void warranty.

3. Ensure deﬂector is seated so bolts are situated at the top of the opening

before tightening. Hand tighten bolts only.

3. Correct Install: Ensure return edge of smoke deﬂector is seated within

the backside of the glass wash.

3. Incorrect Install: Return edge of smoke deﬂector seated under the glass

wash.

F3500 Regency Freestanding Woodstove

installation

BRICK INSTALLATION

Firebrick is included to extend the life of your stove and radiate heat more evenly. Install all ﬁrebricks per the diagram below and place in their correct positions.

Do not use a grate.

1. Remove box of ﬁrebricks from inside unit.

2. Remove LyTherm sheet from mailer tube and install on base of ﬁrebox as shown below.

NOTE: The "AD" brick covers the Ash Dump hole that is used when the Ash Drawer Kit is installed.

LyTherm sheet

Final Install

3. Order of ﬁrebrick install:

a) Rear Firebrick

b) Firebox ﬂoor - install brick over LyTherm sheet

c) Right and left side Firebricks

AD brick

Fire bricks