Panasonic PV-DF2704K Le manuel du propriétaire

Getting Started

TV Operation VCR

Operation

TV / VCR

Operation

Disc

Operation

Information

TV / DVD / VCR Combination

Operating Instructions

Models No.

• Initial Setup and Connection Procedures are on page 18.

As an ENERGY STAR

®

Partner, Panasonic has determined that

this product or product model meets the

ENERGY STAR

®

guidelines for energy efficiency.

Please read these instructions carefully before attempting to connect,

operate, or adjust this product. Please save this manual.

This operating instruction book is designed for use with models PV-DF2004-K and

PV-DF2704-K. Illustrations in this manual show the PV-DF2704-K. Fea tures may vary, so please

read care ful ly.

PV-DF2004-K/PV-DF2704-K

MULTI FORMAT PLAYBACK

*Ability to play back may depend on recording

conditions.

LSQT0812 A

For assistance, please call : 1-800-561-5505 or visit us at www.panasonic.ca

2

Before Using

On your purchase of one of the most

sophisticated and reliable products on the

market today. Used properly, it will bring you

and your family years of enjoyment. Please

fill in the information below. The serial

number is on the tag located on the back of

your unit.

Please check and identify the supplied

accessories.

Use numbers indicated in parentheses

when asking for replacement parts.

Date of Purchase _______________

Dealer Purchased From __________

Dealer Address_________________

Dealer Phone No._______________

Model No. ____________________

Serial No. _____________________

1 Remote Control (EUR7724020)

2 Batteries “AA”

Congratulations

Accessories

The unit may tip or fall if not situated on a

stable surface, if pushed, or during an

earthquake. Use a strong rope or chain

(not included) to fasten the unit firmly to

a strong wall support.

WARNING

Safety Precaution

Be sure to read the following cautions

carefully.

Always grasp

bottom and front

of unit as shown

for proper

balance.

To avoid injury to

hands, always

hold unit by area

shown with arrow

when resting it

on a flat surface.

Never pick unit up

by VCR cassette

opening.

■ PV-DF2704-K only

3

Getting Started

Table of Contents

Getting

Started

TV and VCR

Operation

Disc

Operation

Information

Before Using..................................................................................2

Safety Precautions .......................................................................4

IMPORTANT SAFEGUARDS AND PRECAUTIONS ....................6

Information (Unit, Cassette) ........................................................8

Information (Disc) .........................................................................9

Location of Controls................................................................... 11

Connections ................................................................................14

Initial Setup -Ready to Play- ......................................................18

Tuning TV.....................................................................................19

TV Operation ...............................................................................22

MTS Broadcast / TV Stereo System..........................................24

TV Timer Features.......................................................................25

Closed Caption System..............................................................26

Video / Audio Menu.....................................................................28

Basic VCR Operation -Playback- ..............................................30

Basic VCR Operation -Record-..................................................31

Tape Operation............................................................................32

Timer Recording .........................................................................34

Special VCR Features.................................................................36

Copy Your Tapes (Dubbing).......................................................38

V-Chip Control Features ............................................................39

Display Feature ...........................................................................45

Basic Disc Operation..................................................................46

Disc Operation -In PLAY mode- ................................................48

DVD-RAM Operation...................................................................52

Disc Operation -Using Information Screen- ............................54

Special Disc Operation ..............................................................58

Settings for DVD Operation .......................................................62

Warning and Instruction Displays ............................................67

Before Requesting Service........................................................68

Limited Warranty/Servicentre List ...........................................70

Glossary.......................................................................................72

Specifications .............................................................................73

Index ............................................................................................. 74

Getting Started

TV Operation VCR

Operation

TV / VCR

Operation

Disc

Operation

Information

4

Safety Precautions

This video recorder, equipped with the HQ (High Quality) System, is compatible with

existing VHS equipment. Only use those tapes with the

mark. It is recommended that

only cassette tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour VCR

machines be used. This television receiver provides display of television closed captioning

in accordance with §15.119 of the FCC rules.

WARNING

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

EQUIPMENT TO RAIN OR MOIS TURE.

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO

WIDE SLOT IN WALL SOCKET. FULLY INSERT.

CAUTION

5

Getting Started

CAUTION:

LASER RADIATION WHEN OPEN. DO

NOT STARE INTO BEAM.

(Inside of product)

This television receiver provides display of television closed captioning.

This symbol warns the user that uninsulated

voltage within the unit may have sufficient

magnitude to cause electric shock.

Therefore, it is dangerous to make any kind

of contact with any inside part of this unit.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS

INSIDE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

CAUTION:

UNIT IS A CLASS I LASER PRODUCT.

HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE

HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE

UNIT CORRECTLY AS INSTRUCTED.

WHEN THIS UNIT IS PLUGGED TO THE WALL OUTLET, DO NOT PLACE YOUR EYES

CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK

INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES

OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION

EXPOSURE.

DO NOT OPEN COVERS AND DO NOT ATTEMPT TO REPAIR THE UNIT YOURSELF.

REFER SERVICING TO QUALIFIED PERSONNEL.

This symbol alerts the user that important

literature concerning the operation and

main te nance of this unit has been included.

Therefore, it should be read carefully in order

to avoid any problems.

Apparatus Claims of U.S. Patent Nos. 4,631,603, 4,577,216, 4,819,098, and 4,907,093,

licensed for limited viewing uses only.

This product incorporates copyright protection technology that is protected by method

claims of certain U.S. Patents and other intellectual property rights owned by Macrovision

Corporation and other rights owners. Use of this copyright protection technology must be

authorized by Macrovision Corporation, and is intended for home and other limited viewing

uses only unless otherwise authorized by Macrovision Cor po ra tion. Reverse engineering

or dis as sem bly is prohibited.

6

IMPORTANT SAFEGUARDS AND PRE CAU TIONS

4 DO NOT BLOCK VENTILATION

HOLES

Ventilation openings in the cabinet release heat

generated during operation. If blocked, heat

build-up may result in a fire hazard or heat

damage to cassettes or discs.

For your protection:

a. Never cover ventilation slots while unit is

ON, or operate unit while placed on a bed,

sofa, rug, or other soft surface.

b. Avoid built-in installation, such as a book

case or rack, unless properly ventilated.

5 AVOID EXTREMELY HOT LOCATIONS

OR SUDDEN TEMPERATURE

CHANGES

Do not place unit over or near a heater or

radiator, in direct sunlight, inside closed

vehicles, in high temperature locations [over

95 °F (35 °C)], or in over 75 % humidity. If unit

is suddenly moved from a cold place to a warm

one, moisture may con dense in unit and on the

tape causing damage. Never subject unit to

vibration, impact, or place it so that the surface

is tilted as internal parts may be seriously

dam aged.

6 TO AVOID PERSONAL INJURY

• Never place unit on support or stand that is

not firm, level, and adequately strong. The

unit could fall causing serious injury to a child

or adult and damage to the unit.

• Move any appliance and cart

combination with care. Quick

stops, excessive force, and

uneven surfaces may cause

objects to overturn.

• Carefully follow all operating

instructions.

TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO

PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL

SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN

THE MANUAL AND ON THE PRODUCT.

INSTALLATION

1 POWER SOURCE CAUTION

Operate only from power source indicated on

unit or in this manual. If uncertain, have your

Electric Utility Service Company or Video

Products Dealer verify your home power

source.

2 POWER CORD PLUG

For safety, this unit has a polarized type plug

(one wide blade), or a three-wire grounding

type plug. Always hold the plug firmly and

make sure your hands are dry when plugging

in or unplugging the AC power cord. Regularly

remove dust, dirt, etc. on the plug.

POLARIZED PLUG CAUTION:

The plug fits into outlet only one way. If it

cannot be fully inserted, try reversing it. If it still

will not fit, have an electrician install the proper

wall outlet. Do not tamper with the plug.

GROUNDING PLUG CAUTION:

The plug requires a three-hole grounding

outlet. If necessary, have an electrician install

the proper outlet. Do not tamper with the plug.

3 POWER CORD

To avoid unit malfunction, and to protect

against electrical shock, fire or personal injury:

- Keep power cord away from heating

appliances and walking traffic. Do not rest

heavy objects on, or roll such objects over the

power cord.

- Do not tamper with the cord in any way.

- An extension cord should have the same type

plug (polarized or grounding) and must be

securely connected.

- Overloaded wall outlets or extension cords

are fire hazards.

- Frayed cords, damaged plugs, and damaged

or cracked wire insulation are hazardous and

should be replaced by a qualified electrician.

WARNING

7

Getting Started

1 SAFE ANTENNA AND CABLE

CONNECTION

An outside antenna or cable system must be

properly grounded to provide some protection

against built up static charges and voltage. Part

1 of the Canadian Electrical Code, in U.S.A.

Section 810 of the National Electrical Code.

ANSI/NFPA 70 provides information regarding

proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an

antenna discharge unit, size of grounding

conductors, location of antenna discharge unit,

con nec tion to grounding electrodes, and

requirements for the grounding electrode.

2 KEEP ANTENNA CLEAR OF HIGH

VOLTAGE POWER LINES OR

CIRCUITS

Locate an outside antenna system well away

from power lines and electric light or power

circuits so it will never touch these power

sources should it ever fall. When installing

antenna, absolutely never touch power lines,

circuits or other

power sources as

this could be fatal.

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC

- NATIONAL ELECTRICAL CODE

OUTDOOR ANTENNA INSTALLATION

USING THE UNIT

SERVICE

Before unit is brought out of storage or

moved to a new location, refer again to the

INSTALLATION section of these safe guards.

1 KEEP UNIT WELL AWAY FROM

WATER OR MOISTURE,

such as vases, sinks, tubs, etc.

2 IF EXPOSED TO RAIN, MOISTURE,

OR STRONG IMPACT,

unplug unit and have it inspected by a qualified

service technician before use.

3 ELECTRICAL STORMS

During a lightning storm, or before leaving unit

unused for extended periods of time,

disconnect all equipment from the power

source as well as the antenna and cable

system.

4 WHEN UNIT IS PLUGGED IN

• DO NOT OPERATE IF:

- liquid has spilled into unit.

- unit was dropped or otherwise damaged.

- unit emits smoke, odours, or noises.

Immediately unplug unit, and have it

inspected by a service technician to avoid

potential fire and shock hazards.

• Never drop or push any object through

openings in unit. Touching internal parts may

cause electric shock or fire hazard. Do not

put any foreign object on the tray.

• Keep magnetic objects, such as speakers,

away from unit to avoid electrical interference.

5 USING ACCESSORIES

Use only accessories recommended by the

manufacturer to avoid risk of fire, shock, or

other hazards.

6 CLEANING UNIT

Unplug unit. Use a clean, dry, chemically

untreated cloth to gently remove dust or debris.

DO NOT USE cleaning fluids, aerosols, or

forced air that could over-spray, or seep into

unit and cause electrical shock. Any substance,

such as wax, adhesive tape, etc. may mar the

cabinet surface. Exposure to greasy, humid, or

dusty areas may adversely affect internal parts.

1 DO NOT SERVICE PRODUCT

YOURSELF

If, after carefully following detailed operating

in struc tions, the unit does not operate properly,

do not attempt to open or remove covers, or

make any adjustments not described in the

manual. Unplug unit and contact a qualified

service tech ni cian.

2 REPLACEMENT OF PARTS

Make sure the service technician uses only

parts specified by the manufacturer, or have

equal safety char ac ter is tics as original parts.

The use of unauthorized substitutes may result

in fire, electric shock, or other hazards.

3 SAFETY CHECK AFTER SERVICING

After unit is serviced or repaired, request that a

thorough safety check be done as described in

the manufacturer’s service literature to ensure

video unit is in safe operating condition.

8

Information (Unit, Cassette)

• Insert so the poles (+ and - ) match those in the

remote control.

• Do not use rechargeable type batteries.

1 Open the

cover.

3 Close the

cover.

2 Insert

batteries as

marked.

Only use tapes with the mark in this

unit.

 Break off the tab to protect.

Record Tab

Screw driver

Cover the hole with

cellophane tape.

 To record again.

Do not:

• Mix old and new batteries.

• Use different types at the same time.

• Heat or expose to flame.

• Take apart or short circuit.

• Attempt to recharge alkaline or manganese

batteries.

• Use batteries if the covering has been peeled

off.

Mishandling of batteries can cause

electrolyte leakage which can damage items

the fluid contacts and may cause a fire.

Remove if the remote control is not going to

be used for a long period of time. Store in a

cool, dark place.

 Head Clog Sensor

VIDEO HEADS MAY

NEED CLEANING

PLEASE INSERT HEAD

CLEANING CASSETTE

OR REFER TO MANUAL

END:PLAY

Loading the Batteries

Prevent Accidental Tape Era sure

Head Cleaning

Tape

Speed

Setting

Type of Video Cassette

T60 T120 T160

SP (Standard

Play)

1 Hour 2 Hours

2 Hours

40 Minutes

SLP (Super

Long Play)

3 Hours 6 Hours 8 Hours

Record/Playback Time

Playing older or damaged tapes may

eventually cause video heads to become

clogged.

• Use “dry” type head cleaning cassette only.

(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape directions carefully.

Excessive use of head cleaning tape can shorten

the video head life.

During playback this

screen appears if

clogging is detected.

To clear message

from screen, press

PLAY on the remote

or unit.

Unit auto adjusts clock for DST (Daylight

Saving Time.)

DST (Daylight Saving Time)

• If your area does not observe Daylight Saving

Time, select DST : OFF (see “Manual Clock

Setting” on page 20).

• Keep these time changes in mind when

pro gram ming the unit for timer recording.

■ Spring (First Sunday in April)

DST: ON ➞ Sets clock ahead one hour.

■ Autumn (Last Sunday in October)

DST: ON ➞ Turns clock back one hour.

9

Getting Started

Information (Disc)

*A process that allows play on compatible

equipment.

Discs that can be played

 Discs that cannot be played

DVD with Region No. other than “1” or “ALL”,

DVD from PAL system, DVD-ROM, DVD+R,

DVD-AUDIO, DVD-RW, DVD+RW,

CD-ROM, CDV, CVD, CD-G, CD-TEXT,

SACD, Photo-CD,

Video CD.

 DVDs that can be played

You can play discs with these symbols.

 Playing DVDs

The producer of these discs can control how

they are played so you may not always be

able to control play as described in these

operating instructions. Read the disc’s

instructions carefully.

 CD-R and CD-RW discs

This unit can play CD-R and CD-RW if they

are formatted as CD-DA (digital audio) and

finalized*.

 DVD-R discs

Panasonic DVD-R recorded and finalized*

on a Panasonic DVD video recorder are

played as DVD-Video on this unit.

• It may not be possible to play CD-R, CD-RW,

DVD-R and DVD-RAM in all cases due to the

type of disc or condition of the recording.

Note

Disc type Disc Logo

Indication in

these operating

instructions

DVD-Video

DVD-V

(DVD-Video)

DVD-R*

1

DVD-RAM

*

2

DVD-RAM

CD

(CD-DA)

CD-R

CD-RW

DVD-RAM discs

DVD-RAM discs must meet the following

conditions for this unit to be able to play

them.

• Some parts of the disc, for example where one

program ends and another begins, may not play

smoothly.

• Remove TYPE 2 and 4 discs from their

cartridges before use, then return them when

you are finished. Read the instructions for the

disc carefully.

Non-cartridge disc

TYPE 2 or 4 disc

Type

• Non-cartridge discs

• Discs that can be removed from

their cartridges (TYPE 2 and 4)

Capacity

• 12 cm (5″) 9.4 GB (double-sided)

and 4.7 GB (single-sided)

• 8 cm (3″) 2.8 GB (double-sided)

Do not use irregularly shaped discs (e.g.

heart-shaped), as these can damage the

unit.

*

1

DVD-Video formatted discs [finalized].

*

2

Discs recorded using Version 1.1 of the Video

Recording Format.

10

• The region number of this player is “1”.

• The player will play DVD-Video marked with

labels bearing “1” or “ALL”.

1

For U.S.A. and Canada

Example:

ALL

2

4

1

Disc Handling

This unit is designed and man u fac tured to

respond to the Region Management

Information that is recorded on a DVD disc. If

the Region number described on the DVD

disc does not cor re spond to the Region

number of this unit, this unit cannot play this

disc.

Region Management Information

Handling

precautions

• Sticking a label on the

disc may impair DVD-R

playback.

• Do not attach sticker to

disc. (Do not use discs

with exposed adhesive

from tape or left over

peeled-off stickers.)

• Only hold disc by edges

as shown below.

Fin ger prints, dirt and

scratches can cause

skipping and distortion.

• Do not write on label

side of disc.

• Never use record

cleaning sprays,

benzine, thinner, static

electricity prevention

liquids, or any other

solvent.

• Do not try to close disc

tray when disc is not

properly placed.

Disc tray

Disc

If disc is brought from a cold to a warm

environment, moisture may form on the

disc

Wipe away moisture with a soft, dry, lint-free

cloth before using disc. (See above.)

Improper disc storage

Discs can be damaged if stored or left in

these environment:

• Exposed to direct sunlight.

• Areas that are humid or dusty.

• Near heat (i.e. heater, radiator, etc.).

With a soft, damp (water only) cloth, gently

wipe from the centre hole to the outer edge

as shown below. (Wiping in a circular pattern

will scratch the surface.)

To clean disc surface

• DVD-RAM, DVD-R :

Clean only with the DVD-RAM disc cleaner

available. Never use cloths or cleaners for CDs,

etc.

11

Getting Started

Location of Controls

Remote Control Buttons

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

1

OPEN / CLOSE /

EJECT

When this button is pressed in

TV / VCR mode, the tape is

ejected. This button is

inoperative if pressed during

recording. If pressed in DVD

mode, the disc tray opens or

closes.

2

POWER Turns the unit on or off.

3

DISPLAY

Displays the TV status and

clock. In DVD mode, displays

disc and unit information.

4

RAPID TUNE

Displays the last channel you

were watching.

5

MUTE Mutes the sound instantly.

6

INPUT Changes input source.

7

ACTION Displays Main Menu.

8

SELECT ▲▼◄ ►

Controls navigation around

on-screen menu.

9

CHANNEL

UP/DOWN

Selects a channel.

10

REW/SLOW-

Rewinds tape and searches

previous scene. Decreases slow

motion speed in Still mode.

11

STOP Stops recording or playback.

12

STILL/PAUSE

Pauses picture in Playback

mode and frame advance

picture in Still mode.

13

SKIP- /

SEARCH

Skips back one chapter or track.

Goes to previous menu screen.

Goes directly to the desired

recording.

14

AUDIO Selects the desired audio mode.

15

ANGLE

Selects the desired angle in

DVD mode.

16

REC Records a program.

17

PROGRAM

Displays SET PROGRAM

screen. You can set Timer

Program and On-Timer.

18

DVD Set to DVD mode.

19

TV/VCR Sets to TV/VCR mode.

20

TRACKING UP /

DOWN

Reduces picture noise during

Playback and Slow Motion.

21

NUMBER Keys Selects a channel directly.

22

ADD/DELETE/

CLEAR

Adds or deletes a channel.

Cancels an item on the screen.

23

MENU / PLAY

LIST

Displays DVD menu. Displays

Play List. (DVD-RAM)

24

SET Sets selected menu.

25

VOLUME

UP/DOWN

Adjusts volume.

26

PLAY Begins playback.

27

FF/SLOW+

Fast forwards tape and

searches next scene. Increases

slow motion speed in Still mode.

28

TITLE / D.NAVI

Selects the desired title by

number on some DVDs.

Displays Direct Navigator.

(DVD-RAM).

29

SKIP+ /

CM SKIP / ZERO

SEARCH

Skips one chapter or track.

Goes to next menu screen. In

Stop mode, goes to the counter

“0:00:00”. In Playback mode,

skips over 1 to 3 minutes of

tape.

30

SURROUND / VSS

Creates a deeper, 3-D sound

effect.

31

SUB TITLE

Selects a different subtitle

language.

32

ZOOM/

COUNTER RESET

Enlarges specific portions of

DVD picture. Resets to “0:00:00”

at desired portion of tape.

33

SPEED / RETURN

Returns to DVD menu screen.

Selects recording speed of tape.

12

Front View

Unit Buttons

1

56

23 4

78910

11

12

13

14

15

16

17

18

19

20

21

22 24

23

8' 14'

1

Built In Speakers Equipped with 2 front speakers.

2

Audio Input

Connector 2

Connect from other component.

(LINE 2)

3

Disc Tray Place compatible discs here.

4

Cassette

Compartment

Insert VHS tapes here.

5

Phones Jack

Connect an ear phone or

headphones.

6

Video Input

Connector 2

Connect from other component.

(LINE 2)

7

POWER Turns the unit on or off.

8

DVD Operation

STOP Stops playback.

8'

STILL

(PV-DF2004-K

only)

Pauses picture in Playback

mode and frame advance picture

in Still mode.

9

PLAY Begins playback.

10

SKIP ◄◄

Skips back one chapter or track.

Goes to previous menu screen.

11

SKIP►►

Skips one chapter or track. Goes

to next menu screen.

12

OPEN/CLOSE Opens or closes the disc tray.

13

VOLUME

UP/DOWN

Adjusts volume.

14

CHANNEL

UP/DOWN or

TRACKING

UP/DOWN

Selects a channel.

Reduces picture noise during

Playback and Slow Motion.

14'

INPUT

(PV-DF2004-K

only)

Changes input source.

15

VCR Operation

STOP/

EJECT

STOP:

Stops playback.

EJECT:

Ejects the tape.

16

PLAY/

REPEAT

PLAY:

Begins playback.

REPEAT:

Sets to see a recording over and

over.

17

REWIND/

SEARCH

Rewinds tape and searches

previous scene. Decreases slow

motion speed in Still mode.

18

FAST

FORWARD/

SEARCH

Fast forwards tape and searches

next scene. Increases slow

motion speed in Still mode.

19

REC Records a program.

20

Remote Sensor

Receives infrared signal from

remote control.

21

REC Indicator

(RED)

Lights up during recording. In

Rec Pause or OTR Pause mode,

the Indicator flashes.

22

ON TIMER

Indicator

(ORANGE)

Lights when the On Timer is set.

23

PROG TIMER

Indicator

(GREEN)

Lights up when the unit is set for

Timer Recording. It flashes

when a Timer Recording has

been set with no tape inserted,

the clock is not set, or the tape is

in motion. Lights up when the On

Timer is set.

24

ANGLE Indicator

(RED)

Lights up when a scene

recorded multiple angles is

detected. (DVD only)

13

Getting Started

Rear View

1 AC Power Plug

When plugged into an

AC outlet, this unit

consumes 1.5 W of

electric power in OFF

condition.

2

Optical digital audio output

connector

Outputs audio signal.

(Digital)

3

Audio Output Connector

(L/R)

Outputs audio signal.

(Analog)

4 Audio Input Connector 1

Connect from other

component. (LINE 1)

5 Video Input Connector 1

Connect from other

component. (LINE 1)

6

VHF/UHF Antenna

Input Terminal

Input terminal for an

antenna or cable box

signal.

12 3 45 6

14

Connections

 Antenna Connection

Connect the cable from Antenna to the VHF/UHF terminal on the unit.

 Cable Connection

Connect the cable supplied by your local cable company to VHF/UHF terminal on the unit.

Overtightening “Nut type” RF coaxial cables may damage jacks.

Finger tighten only.

• Turn off the power supply for all com po nents before making any connections.

• If the cables necessary for connecting a component to the system are not included with the

component or available as an option, you may need to fashion a cable to suit the component

concerned.

• Read the instruction manual for each system component care ful ly before connecting it.

Notes on con nec tions

Connecting the RF in Terminal

Note to CABLE system installer:

This re mind er is pro vid ed to call

the CABLE (Cable TV) System

Installer’s at ten tion to Article

820-40 of the NEC that pro vides

guide lines for proper grounding

and, in par tic u lar, specifies that

the cable ground shall be

con nect ed to the ground ing

system of the build ing, as close to

the point of cable entry as

practical.

CAUTION

Or

Cable Box

In from CABLE

Mixer

VHF

Antenna

UHF

Antenna

15

Getting Started

Connects VCRs and other peripheral equipment

 AV Input terminal 1 is used

Connecting the “1, 2” AV Input Terminals

• Similar connections are available at the “1, 2” AV input terminals.

• AV Input terminal 2 is located on the front of the unit.

Notes

Audio

OUT

Video

OUT

RL

16

Enjoy the powerful movie theatre and hall-like sound available with multiple channel audio

found on DVDs by connecting an amplifier and speakers. There are two types of connection,

digital and analog.

Connect an amplifier with Dolby Digital or

DTS decoders to enjoy surround sound.

Connect an amplifier to enjoy high-quality

stereo sound with sampling frequencies of

96 kHz.

 Analog connection Digital connection

Connecting the Audio Output Terminal

OPTICAL

Firmly connect

the cable to the

connector.

Speakers (example)

Please see

amplifier manual

for speaker

requirements.

Speakers (example)

Amplifier

Amplifier with built in

Dolby Digital or DTS

decoders.

17

Getting Started

Manufactured under license from Dolby

Laboratories. “Dolby,” “Pro Logic,” and the

double-D symbol are trademarks of Dolby

Laboratories.

IMPORTANT NOTE:

Caution for optical digital audio output

connector:

• When connecting an amplifier (with an optical

digital input connector) which does not contain

the Dolby Digital or dts decoder, be sure to

select “PCM” at “Dolby Digital” and “PCM” at “dts”

in the Settings for DVD Operation “Selecting

AUDIO OUTPUT” (see pages 64-65). Otherwise,

any attempt to play DVDs may cause such a high

level of noise that it may be harmful to your ears

and damage your speakers.

• Be sure to refer to pages 64-65 regarding output

settings of Dolby Digital, dts, and PCM.

• CDs can be played as usual.

Notes on audio output from the optical

digital audio output con nec tor

Enjoying digital audio output from the

digital audio output con nec tor

*

1

The type of audio output from the connector can

be selected by adjusting the Settings for DVD

Operation. (See pages 64-65.)

*

2

When "LPCM" is set to OFF in the DVD Main

Menu, only 48 kHz sampling/16 bit is output.

When set to ON, sampling of sound quality

greater than 48 kHz/16 bit is reduced to

48 kHz/16 bit. (See pages 64-65.)

For your reference:

• Dolby Digital is a digital sound compression

technique developed by the Dolby Laboratories

Licensing Corporation. Supporting 5.1-channel

surround sound, as well as stereo (2-channel)

sound, this technique enables a large quantity of

sound data to be efficiently recorded on a disc.

• Linear PCM is a signal recording format used in

CDs. While CDs are recorded in 44.1 kHz/16 bit,

DVDs are recorded in 48 kHz/16 bit up to

96 kHz/24 bit.

• If you have a Dolby Pro Logic Surround decoder,

you will obtain the full benefit of Pro Logic from

the same DVD movies that provide full 5.1

channel Dolby Digital soundtracks, as well as

from titles with the Dolby Surround mark. For

information on Panasonic or Technics Dolby Pro

Logic Surround Sound Decoders please contact

your local dealer.

Turn down the volume, then turn this unit, as

well as other equipment to be connected, off

before pro ceed ing with connection.

Do not block ventilation holes of any equipment

and arrange it so that air can circulate freely.

Check List

Note

• Some dts decoders which do not support

DVD-dts Interface may not work properly with

the unit.

Disc

Sound

recording

format

Optical digital audio

output from connector

DVD-V

Dolby Digital

Dolby Digital bitstream

(1-5.1 ch) or PCM (48 kHz

sampling/16 bit only)*

1

Linear PCM

(48/96 kHz

16/20/24 bit)

Linear PCM (2ch)

(48 kHz sampling/16 bit

only)*

2

dts

Bitstream or PCM (48 kHz

sampling/16 bit only)*

1

DVD-RAM

Dolby Digital

Dolby Digital bitstream

(1-5.1 ch) or PCM (48 kHz

sampling/16 bit only)*

1

Linear PCM

(48 kHz

16 bit)

Linear PCM (2ch)

CD

Linear PCM

(44.1 kHz sampling)

Manufactured under license from Digital

Theatre Systems, Inc. US Pat. No’s.

5,451,942, 5,956,674, 5,974,380,

5,978,762, 6,487,535 and other U.S. and

world-wide patents issued and pending.

“DTS” and “DTS 2.0 + Digital Out” are

trademarks of Digital Theatre Systems,

18

Please make all cable or antenna

connections before powering on.

Plug the unit power cord into an AC wall

outlet.

Settings are made

automatically. When

complete, this screen

appears.

If setup is incomplete,

the following screen

appears. Check

connection of

Antenna/Cable to the

RF in Terminal, then

try to manually set the

clock as follows.

a. Press ACTION on the Remote to

display SET CLOCK Menu screen.

b. Press ▲▼ to select the month and

press SET to set. In the same

manner, select and set the date, year,

time, and DST (Daylight Saving Time).

• Press ◄ repeatedly to move the cursor. Press

▲▼ to make a correction.

c. Press ACTION twice to start CLOCK

and exit.

POWER

ACTION

SET

CH AUTO SET PROCEEDING

AUTO CLOCK SET

PROCEEDING

CANCEL:STOP

10/25/2004 MON 11:45AM

DST:ON

SETTING : CH 10

AUTO CLOCK SET

COMPLETED

AUTO CLOCK SET

IS INCOMPLETE

PLEASE SET CLOCK BY

PRESSING ACTION KEY

SET CLOCK

1/ 1/2004 THU 12:00AM

DST:ON

SELECT: SET:SET

START :ACTION

SET CLOCK

10/25/2004 MON 11:45AM

DST:ON

SELECT: SET:SET

START :ACTION

Case 1

Case 2

Initial Setup (Ready to Play)

Initial Setup -Ready to Play-

• Function buttons are void during Initial Setup.

• To eject a tape during Auto Set, press EJECT on

remote. Then make settings manually. (See

pages 19-21.)

• If Auto Clock Set takes more than 30 minutes,

press STOP and perform settings manually. (See

pages 19-21.)

SELECT

▲▼◄ ►

EJECT

STOP

POWER

STOP

VOL+

• If you use a cable

box, turn it on and

set it to the Public

Broadcasting

Service (PBS)

channel in your

time zone. If you

use a DSS

receiver, it must be

turned off.

1 Press POWER on the remote or unit.

3 Auto channel and clock set starts.

2 Press ▲, ▼, or

VOL+ to select

language.

SELECT LANGUAGE

PRESS CH :English

APPUYER CH :Français

OPRIMIR VOL+ :Español

19

TV Operation

5 Press ▲▼ to select “AUTO SET,”

then press SET.

• After Channel Auto Set is finished, Clock Auto

Set will be performed. (If clock is set manually,

Clock Auto Set will not be performed.)

2 Press ▲▼◄ ► to select “CH.”

3 Press SET.

1 Press ACTION to display MAIN

MENU.

 To add channel:

Select channel with NUMBER keys and

press ADD/DLT.

 To delete channel:

Select channel with CH ▲▼ or NUMBER

keys and press ADD/DLT.

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET

END :ACTION

SET UP CHANNEL

ANTENNA : CABLE

AUTO SET

WEAK SIGNAL DISPLAY:OFF

SELECT: SET:SET

END :ACTION

CHANNEL 08 ADDED

CHANNEL 08 DELETED

Automatic Channel Setting

4 Press ▲▼ to select “ANTENNA,” then

press SET to set your antenna

system (“TV” or “CABLE”).

Add or Delete a Chan nel

Tuning T V

SELECT

▲▼◄ ►

ACTION

SET

ADD/DLT

NUMBER

keys

CH▲▼

20

SET CLOCK

10/25/2004 MON 11:45AM

DST:ON

SELECT: SET:SET

END :ACTION

4 Press ▲▼ to select “MANUAL,” then

press SET.

(“TIME ZONE ADJUST” appears only when

auto clock is set.)

2 Press ▲▼◄ ► to select “CLOCK.”

3 Press SET.

1 Press ACTION to display MAIN

MENU.

5 Press ▲▼ and press SET to select

and set the month, date, year, time,

and DST (Daylight Saving Time).

To Make Corrections, repeatedly

press ◄ to move to error, then

correct.

6 Press ACTION twice to start the

clock and exit this mode.

SET CLOCK

AUTO CLOCK SET

MANUAL

TIME ZONE ADJUST : 0

SELECT: SET:SET

END :ACTION

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET

END :ACTION

Manual Clock Setting

4 Press ▲▼ to select “AUTO CLOCK

SET,” then press SET.

3 Press SET.

SET CLOCK

AUTO CLOCK SET

MANUAL

SELECT: SET:SET

END :ACTION

2 Press ▲▼◄ ► to select “CLOCK.”

1 Press ACTION to display MAIN

MENU.

MAIN MENU

DVD LOCK LANGUAGE

TV CLOCK CH

SELECT: SET:SET

END :ACTION

Automatic Clock Setting

ACTION

SET

SELECT

▲▼◄ ►

POWER

PLAY/REPEAT

FF

La page charge ...

Panasonic PV-DF2704K Le manuel du propriétaire

Ce manuel convient également à

Panasonic PV-DF2704K Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents