Wacker Neuson RD7-RAW Manuel utilisateur

5000185489 18 0812

Operator’s Manual

Roller

RD 7

Notice d’Emploi

Rouleau

5000185489

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000185465 18 0812

RD 7 Foreword

wc_tx001345gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

;

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Machine Item Number

RD 7H 0008042

RD 7H-ES 0009408, 0620794

RD 7H-S 0009487, 0620795

RD 7-RAW 0620079, 0620478, 0620596

Foreword RD 7

4 wc_tx001345gb.fm

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

2012-CE-RD7H_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

RD 7H-ES, RD 7H-S

Vibrating Walk-Behind Rollers

To compact asphalt

0620794, 0620795

5,1 kW

107 dB(A)

108 dB(A)

Conformity Assessment Procedure

According to ANNEX VIII

Notified Body

Lloyds Register Quality Assurance Limited (Notified Body No 0088)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 16.02.2012

William Lahner

Managing Director

Paul Sina

Manager, Product Engineering

Todd Lutz

Director of Business Development

Original Declaration of Conformity

wc_bo5000185465_18TOC.fm 7

Table of ContentsRD 7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Operating Safety ................................................................................ 11

1.4 Operator Safety While Using Internal Combustion Engines ............... 13

1.5 Service Safety .................................................................................... 14

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 22

4 Operation 23

4.1 Preparing the Machine for First Use ................................................... 23

4.2 Controls and Service Locations .......................................................... 24

4.3 Position of the Operator ..................................................................... 25

4.4 Refueling the Machine ........................................................................ 26

4.5 Before Starting ................................................................................... 27

4.6 Engine Throttle Control ...................................................................... 27

4.7 Starting the Machine (RD 7H, RD 7H-S) ............................................ 28

4.8 Starting the Machine (RD 7H-ES) ...................................................... 29

4.9 Cold Weather Starting (RD 7H, RD 7H-S) ......................................... 30

4.10 Engine Speed ..................................................................................... 31

4.11 Stopping the Machine ......................................................................... 31

4.12 Direction and Speed Control .............................................................. 32

4.13 Exciter ................................................................................................ 32

4.14 Back-Up Stop Pad .............................................................................. 33

4.15 Engine Crank ...................................................................................... 33

4.16 Parking Brake ..................................................................................... 34

4.17 Watering System ................................................................................ 34

4.18 Machine Stability ................................................................................ 35

4.19 Operation on Slopes ........................................................................... 36

4.20 Rollovers ............................................................................................ 36

4.21 Emergency Shutdown Procedure ....................................................... 37

8 wc_bo5000185465_18TOC.fm

Table of Contents RD 7

5 Maintenance 38

5.1 Maintenance Schedule ........................................................................38

5.2 Checking Engine Oil ............................................................................41

5.3 Changing Engine Oil and Oil Filter ......................................................42

5.4 Fuel System ........................................................................................43

5.5 Engine Air Filter ...................................................................................45

5.6 Checking and Adjusting Valve Clearances .........................................46

5.7 Engine Cooling System .......................................................................47

5.8 Mechanical Oil Pressure Monitoring ....................................................48

5.9 Scraper Bars .......................................................................................49

5.10 Water Spray Bars ................................................................................50

5.11 Hydraulic Oil Requirements .................................................................51

5.12 Hydraulic Oil Level ..............................................................................52

5.13 Changing Hydraulic Fluid and Filter ....................................................53

5.14 Direction Lever Adjustment .................................................................54

5.15 Pressure Washing the Machine ..........................................................56

5.16 Storing the Machine ............................................................................56

6 Troubleshooting 57

7 Technical Data 58

7.1 Engine .................................................................................................58

7.2 Roller ...................................................................................................59

7.3 Lubrication ...........................................................................................59

7.4 Sound and Vibration Measurements ...................................................60

8 AEM Safety Manual 61

9 Schematics 88

9.1 Hydraulic Schematic ............................................................................88

9.2 Hydraulic Schematic Components ......................................................89

9.3 Hydraulic Diagram ...............................................................................90

9.4 Hydraulic Diagram Components .........................................................91

9.5 RD 7H ES—Electrical Schematic ........................................................92

9.6 RD 7H-ES—Electrical Schematic Components ..................................93

RD 7 Safety Information

wc_si000115gb.fm 9

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

Safety Information RD 7

10 wc_si000115gb.fm

1.2 Machine Description and Intended Use

This machine is a dual drum vibratory walk-behind roller. The Wacker

Neuson Walk-Behind Roller consists of an upper frame to which are

mounted a diesel engine, a hydraulic tank, a water tank, and a

hydrostatic drive system, and a lower frame which supports two steel

drums, an exciter assembly, and a handle. The engine powers the

hydraulics that provide machine movement and drum vibration. The

vibrating drums smooth and compact the work surface as the

machine moves. The operator uses the handle to control machine

speed and direction.

This machine is intended to be used for compacting sand, gravel, soil,

and asphalt on roadways, walkways, bridges, and parking lots.

This machine has been designed and built strictly for the intended use

described above. Using the machine for any other purpose could

permanently damage the machine or seriously injure the operator or

other persons in the area. Machine damage caused by misuse is not

covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to tow other machines

• Using the machine to spray liquids other than water (i.e., diesel fuel

on asphalt)

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual.

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Burns from hot hydraulic fluid

• Fire hazards from improper refueling techniques

• Fuel and its fumes

• Personal injury from improper lifting techniques or operating tech-

niques

RD 7 Safety Information

wc_si000115gb.fm 11

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

1.3 Operating Safety

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

• children

• people impaired by alcohol or drugs

Contact Wacker Neuson for additional training if necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

1.3.1 ALWAYS operate the machine with both of your feet on the ground! DO NOT

stand, sit, or ride on machine while in operation.

1.3.2 Always operate machine with all safety devices and guards in place and in

working order. Do not modify or defeat safety devices. Do not operate machine

if any safety devices or guards are missing or inoperative.

1.3.3 ALWAYS check that all controls are functioning properly immediately after

start-up! DO NOT operate the machine unless all controls operate correctly.

1.3.4 ALWAYS remain aware of changing surface conditions and use extra care

when operating over uneven ground, on hills, or over soft or coarse material.

The machine could shift or slide unexpectedly.

WARNING

Safety Information RD 7

12 wc_si000115gb.fm

1.3.5 ALWAYS use caution when operating near the edges of pits, trenches or

platforms. Check to be sure that the ground surface is stable enough to

support the weight of the machine with the operator and that there is no danger

of the roller sliding, falling, or tipping.

1.3.6 ALWAYS position yourself safely when operating machine in reverse or on

hills. Leave enough space between yourself and the machine so you will not

be placed in a hazardous position should the machine slide or tip.

1.3.7 Make sure that all other persons are at a safe distance from the machine. Stop

the machine if people step into the working area of the machine.

1.3.8 ALWAYS remain aware of moving parts and keep hands, feet, and loose

clothing away from the moving parts of the machine.

1.3.9 ALWAYS remain aware of changing positions and the movement of other

equipment and personnel on the job site.

1.3.10 Do not subject the roller to jarring impacts by driving it off curbs or off the back

of a truck or trailer.

1.3.11 NEVER operate the machine with the fuel cap loose or missing.

1.3.12 Do not operate the machine with unapproved accessories or

attachments.

1.3.13 Do not transport the machine while it is running.

1.3.14 Do not leave the machine running unattended.

1.3.15 Do not use accessories or attachments that are not recommended by Wacker

Neuson. Damage to equipment and injury to the user may result.

1.3.16 Do not touch the engine or muffler while the engine is on or immediately after

it has been turned off. These areas get hot and may cause burns.

1.3.17 Do not operate a machine in need of service or repair.

1.3.18 ALWAYS do periodic maintenance as recommended in the Operator’s

Manual.

1.3.19 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

1.3.20 Do not use a cellphone or send text messages while operating this machine.

RD 7 Safety Information

wc_si000115gb.fm 13

1.4 Operator Safety While Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

• Use suitable tools for refueling (for example, a fuel hose or funnel).

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

Safety Information RD 7

14 wc_si000115gb.fm

1.5 Service Safety

A poorly maintained machine can become a safety hazard! In order

for the machine to operate safely and properly over a long period of

time, periodic maintenance and occasional repairs are necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

1.5.1 ALWAYS check all external fasteners at regular intervals.

1.5.2 Do not modify the machine without the express written approval of the

manufacturer.

1.5.3 Do not attempt to clean or service the machine while it is running. Rotating

parts can cause severe injury.

1.5.4 Do not use gasoline or other types of fuels or flammable solvents to clean

parts, especially in enclosed areas. Fumes from fuels and solvents can

become explosive.

1.5.5 Some service procedures require that the machine’s battery be disconnected.

To reduce the risk of personal injury, read and understand the service

procedures before performing any service to the machine.

1.5.6 ALWAYS make sure slings, chains, hooks, ramps, jacks, and other types of

lifting devices are attached securely and have enough weight-bearing capacity

to lift or hold the machine safely. Always remain aware of the location of other

people in the area when lifting the machine.

1.5.7 ALWAYS turn the engine off before servicing the machine. If the engine has

electric start, disconnect the negative terminal on the battery before servicing

the machine.

1.5.8 Keep the area around the muffler free of debris such as leaves, paper, cartons,

etc. A hot muffler could ignite the debris and start a fire.

1.5.9 Do not tip the machine for cleaning or for any other reason.

1.5.10 DO NOT open hydraulic lines or loosen hydraulic connections while the engine

is running! Hydraulic fluid under pressure can penetrate the skin, cause burns,

blind, or create other potentially dangerous hazards. Set all controls in neutral

and turn engine off before loosening the hydraulic lines.

WARNING

RD 7 Safety Information

wc_si000115gb.fm 15

1.5.11 Fluid leaks from small holes are often practically invisible. DO NOT use your

bare hands to check for leaks. Check for leaks using a piece of cardboard or

wood.

1.5.12 Always make sure hose connections have been reconnected back to the

correct fitting. Failure to do so may result in damage to the machine and/or

injury to person on or near the machine.

1.5.13 All adjustments and repairs MUST be completed before operation. Do not

operate the machine with a known problem or deficiency! All repairs and

adjustments should be completed by a qualified technician.

1.5.14 Before you start the machine, ensure that all tools have been removed from

the machine and that replacement parts and adjusters are firmly tightened.

1.5.15 When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

1.5.16 Keep the machine clean and labels legible. Replace all missing and hard-to-

read labels. Labels provide important operating instructions and warn of

dangers and hazards.

1.5.17 ALWAYS replace safety devices and guards after repairs and maintenance.

Labels RD 7

16 wc_si000398gb.fm

2Labels

2.1 Label Locations

SR

E

P

O

L

M

H

G

M

B, F, U

A

S

C

T

J

K

D

L

Q

V

N

RD 7 Labels

wc_si000398gb.fm 17

2.2 Label Meanings

Wacker Neuson machines use international pictorial labels where

needed. These labels are described below.

A

DANGER!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an

enclosed area unless adequate ventilation,

through such items as exhaust fans or hoses,

is provided.

 Read the Operator’s Manual. No sparks,

flames, or burning objects near the machine.

Stop the engine before refueling.

B

WARNING!

Hot surface

C

WARNING!

Read and understand the supplied Operator’s

Manual before operating the machine. Failure

to do so increases the risk of injury to yourself

and others.

D

WARNING!

To prevent hearing loss, wear hearing

protection when operating the machine.

0178715

STOP

Labels RD 7

18 wc_si000398gb.fm

E

Guaranteed sound power level in dB(A).

F

CAUTION!

Use only clean, filtered diesel fuel.

G

Operator’s Manual must be stored on machine.

A replacement Operator’s Manual can be

ordered through your local Wacker Neuson

distributor.

H

Water control valve.

J

Vibration control ON/OFF.

K

NOTICE

No lift point.

E L M A N U A L D E O P E R A C I O N D E B E

S E R R E T E N I D O E N L A M A Q U I N A .

C O N T A C T E A S U D I S T R I B U I D O R

W A C K E R M A S C E R C A N O P

A R A

P E D I R U N E J E M P L A R

A D I C I O N A L .

L A N O T I C E D ' E M P L O I D O I T

E T R E M U N I E S U R L A M A C H I N E .

C O N T A C T E R L E D I S T R I

B U T E U R

W A C K E R L E P L U S P R O C H E

P O U R C O M M A N D E R U N

E X E M P L A I R E S U P P L E M E N T A I R E .

1 1 5 0 9 6

O P E R A T O R ' S M A N U A L M U S T B E

S T O R E D O N M A C H I N E .

R E P L A C E M E N T O P E R A T O R ' S

M A N U A L C A N B E O R D E R E D

T H R O U G H Y O U R

L O C A L W A C K E R

D I S T R I B U T O R .

D I E B E T R I E B S V O R S C H R I F T M U S S

A N D E R M A S C H I N E A U F B E W A H R T

W E R D E N . Z U R B E S T E L L U

N G V O N

E R S A T Z B Ü C H E R N W E N D E N S I E

S I C H B I T T E A N I H R E N

Ö R T L I C H E N W A C K E R H Ä N D L E R .

RD 7 Labels

wc_si000398gb.fm 19

L

NOTICE

Lifting point.

M

Tie-down point

N

Engine oil drain.

O

Hydraulic oil reservoir fill

P

Hydraulic oil drain.

Q

Key switch, engine start:

Off

On

Start

R

This machine may be covered by one or more

patents.

178709

Labels RD 7

20 wc_si000398gb.fm

S

A nameplate listing the model number, item

number, revision number, and serial number is

attached to each unit. Please record the infor-

mation found on this nameplate so it will be

available should the nameplate become lost or

damaged. When ordering parts or requesting

service information, you will always be asked to

specify the model number, item number, revi-

sion number, and serial number of the unit.

T

—

Check engine oil level.

Use SAE10W30.

Check the fuel level.

—

Engage parking brake.

—

Turn vibration off.

—

Pull engine throttle out.

La page charge ...

Wacker Neuson RD7-RAW Manuel utilisateur

Ce manuel convient également à

Wacker Neuson RD7-RAW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents