Askey AP6275S Manuel utilisateur

AP6275S
Marque
Askey
Modèle
AP6275S
Catégorie
Antennes réseau
Taper
Manuel utilisateur
AP6275S User manual
Product Name
WIFI+BT Combo Module
Brand Name
ASKEY
Model Name
AP6275S
Rating Voltage:
DC 3.3V
Frequency Range:
2.4GHz:
2.400 GHz ~ 2.4835 GHz (2.4GHz ISM Band)
5GHz:
5.15~5.35GHz, 5.47~5.725GHz, 5.725~5.85GHz
(5GHz UNII Band)
Channels
2.4GHz: Ch1 ~ Ch11
5.15~5.35 GHz: Ch36 ~ Ch64
5.47~5.725GHz: Ch100 ~ Ch142
5.725~5.85GHz: Ch149 ~ Ch165
Antenna Type:
PIFA antenna
Hardware version:
V01
Software Version:
Android 10
Product Features
IEEE 802.11 Key Feature
⚫ Lead Free design which is compliant with ROHS requirements.
⚫ TX and RX low-density parity check (LDPC) support for improved range and
power efficiency.
⚫ Dual-stream spatial multiplexing up to 1200 Mbps data rate.
⚫ 20, 40, 80 MHz channels with optional SGI (1024 QAM modulation)
⚫ Real simultaneous dual-band
⚫ Client MU-MIMO
⚫ Supports standard SDIO v3.0, compatible with SDIO v2.0 HOST interfaces.
Bluetooth Key Feature
⚫ BT host digital interface:
- HCI UART (up to 4 Mbps)
- PCM for audio data
⚫ Complies with Bluetooth Core Specification Version 5.0 with provisions for
supporting future specifications. With Bluetooth Class 1 or Class2 transmitter
operation.
⚫ Supports extended synchronous connections (eSCO), for enhanced voice quality
by allowing for retransmission of dropped packets.
⚫ Adaptive frequency hopping (AFH) for reducing radio frequency interference.
A simplified block diagram of the module is depicted in the figure above.
Wi-Fi RF Specification
2.4GHz RF Specification
5GHz RF Specification
Note: The frequencies that fall in the 5600MHz to 5650MHz band will not be used in Canada.
Bluetooth RF Specification
Frequency Range:
802.11b/g/n-HT20/ax-HE20: 2412 ~ 2462MHz
Channel Number:
802.11b/g/n-HT20/ax-HE20: 11
Type of Modulation:
802.11b: DSSS
802.11g/n: OFDM
802.11ax: OFDMA
Frequency Range:
For 802.11a/n-HT20/ac-VHT20/ax-HE20:
5180~5240MHz, 5260~5320MHz, 5500~5720MHz, 5745~5825MHz
For 802.11n-HT40/ac-VHT40/ax-HE40:
5190~5230MHz, 5270~5310MHz, 5510~5710MHz, 5755~5795MHz
For 802.11ac-VHT80/ax-HE80:
5210MHz, 5290MHz, 5530MHz, 5610MHz, 5690MHz, 5775MHz
Type of Modulation:
802.11a/n/ac: OFDM
802.11ax: OFDMA
Operating Frequency:
Channel Number:
Type of modulation:
External clock reference
U.S. FCC Statement
FCC ID: H8N-AP6275S
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
o Reorient or relocate the receiving antenna.
o Increase the separation between the equipment and receiver.
o Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
o Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or
operating in conjunction with any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
Canada (IC) Notices
IC: 1353A-AP6275S
CAN ICES-003(B) / NMB-003(B)
This device complies with Industry Canada license-exempt RSSs. Operation is subject
to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes:
1. l’appareil ne doit pas produire de brouillage
2. l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si
le brouillage est susceptible d’en compromettre le fonctionnement.
Caution:
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems.
Avertissement:
Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour
une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les memes canaux.
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20 cm between the radiator & your body.
Cet équipement est conforme aux limites d’exposition aux rayonnements
IC établies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre
corps.
OEM Integration Instructions：
Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2.
This module is limited to installation in mobile or fixed applications, according to Part
2.1091(b). 3. The separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and different antenna
configurations 4. For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for
additional testing to verify compliance as a composite system. When testing the host device
for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance
with Part 15 Subpart B while the transmitter module(s) are installed and operating. The
modules should be transmitting, and the evaluation should confirm that the module's
intentional emissions are compliant (i.e. fundamental and out of band emissions). The host
manufacturer must verify that there are no additional unintentional emissions other than what
is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s).
The Grantee will provide guidance to the host manufacturer for Part 15 B requirements if
needed.
IMPORTANT NOTE：
Notice that any deviation(s) from the defined parameters of the antenna, as described by the
instructions, require that the host product manufacturer must notify to Askey that they wish to
change the antenna trace design. In this case, a Class II permissive change application is
required to be filed by the USI, or the host manufacturer can take responsibility through the
change in FCC ID (new application) procedure followed by a Class II permissive change
application.
End Product Labeling
When the module is installed in the host device, the FCC/IC label must be visible through a
window on the final device or it must be visible when an access panel, door or cover is easily
re-moved. If not, a second label must be placed on the outside of the final device that contains
the following text: “Contains Transmitter Module FCC ID: H8N-AP6275S or Contains FCC
ID: H8N-AP6275S”. The FCC ID/IC Certification Number can be used only when all
FCC/IC compliance requirements are met.
Antenna
(1) The antenna must be installed such that 20 cm is maintained between the antenna and
users.
(2) The transmitter module may not be co-located with any other transmitter or antenna.
In the event that these conditions cannot be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC/IC authorization is no longer considered
valid, and the FCC ID/IC Certification Number cannot be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC/IC authorization.
To comply with FCC regulations limiting both maximum RF output power and human
exposure to RF radiation, maximum antenna gain (including cable loss) must not exceed.
Antenna Specification:
Antenna Type
Frequency Band
(GHz)
TX
Paths
Per Chain Max Antenna
Gain (dBi)
CDD Directional Gain
(dBi)
Ant 0
Ant 1
For Power
For PSD
Wi-Fi Internal Antenna
PIFA
2412 ~ 2462
2
2.1
1.9
2.1
5.11
5180 ~ 5240
2
4.2
1.9
4.2
7.21
5260 ~ 5320
2
3.8
3.0
3.8
6.81
5500 ~ 5720
2
3.8
2.9
3.8
6.81
5745 ~ 5825
2
3.4
2.3
3.4
6.41
Bluetooth Internal Antenna
PIFA
2402 ~ 2480
1
1.9
--
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module. The end user manual shall include all required regulatory information/warning as
show in this manual.
List of applicable FCC rules
This module has been tested and found to comply with part 15 requirements for Modular
Approval.
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC
transmitter rules) listed on the grant, and that the host product manufacturer is responsible for
compliance to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart
B compliant (when it also contains unintentional-radiator digital circuity), then the grantee
shall provide a notice stating that the final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.
1. List of applicable FCC rules. KDB 996369 D03, Section 2.2
Complies with FCC Part 15.247 & Part 15.407.
2. Summarize the specific operational use conditions. KDB 996369 D03, Section 2.3
Refer to Antenna specification.
3. Limited Module Procedures. KDB 996369 D03, Section 2.4
This module is approved as single module.
4. Trace antenna designs. KDB 996369 D03, Section 2.5
Refer to Antenna specification.
5. RF exposure considerations. KDB 996369 D03, Section 2.6
The antennas used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter.
6. Antennas. KDB 996369 D03, Section 2.7
Refer to Antenna specification.
7. Label and compliance information. KDB 996369 D03, Section 2.8
Refer label file.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and
users, and
2) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.
Industry Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to
the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement."
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following
conditions: (For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co-located with any other transmitter or antenna. As
long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans
les conditions suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur
son produit final pour toutes exigences de conformité supplémentaires requis pour ce module
installé.
IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or
colocation with another transmitter), then the Canada authorization is no longer considered
valid, and the IC ID cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur),
l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé
sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le
produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following: “Contains IC: 1353A-AP6275S”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre
l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec
l'inscription suivante: " Contains IC: 1353A-AP6275S ".
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du
produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
Dimensions
Label
Recommended Reflow Profile
Package Information
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Askey AP6275S Manuel utilisateur

AP6275S
Marque
Askey
Modèle
AP6275S
Catégorie
Antennes réseau
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents