Sony XR-L240 Manuel utilisateur

Marque: Sony

Modèle: XR-L240

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

 2002 Sony Corporation

FM/MW/LW

Cassette Car Stereo

3-236-756-11 (1)

XR-L240

Operating Instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Wichtig!

Bitte nehmen Sie sich etwas Zeit, um den Geräte-Pass

vollständig auszufüllen. Dieser befindet sich auf der

hinteren Umschlagseite dieser Bedienungsanleitung.

Si dichiara che l’apparecchio è stato fabbricato in conformità all’art. 2, Comma 1 del

D.M. 28.08.1995 n. 548.

For installation and connections, see the supplied installation/connections

manual.

Zur Installation und zum Anschluß siehe die mitgelieferte Installations-/

Anschlußanleitung.

En ce qui concerne l’installation et les connexions, consulter le manuel

d’installation/connexions fourni.

Per l’installazione e i collegamenti, fare riferimento al manuale di istruzioni di

installazione/collegamenti in dotazione.

Zie voor het monteren en aansluiten van het apparaat de bijgeleverde handleiding

“Installatie en aansluitingen”.

Welcome !

Thank you for purchasing this Sony Cassette

Player.

Precautions

• If your car was parked in direct sunlight

resulting in a considerable rise in

temperature inside the car, allow the unit to

cool off before operating it.

• If no power is being supplied to the unit,

check the connections first. If everything is in

order, check the fuse.

• If no sound comes from the speakers of a

two-speaker system, set the fader control to

the centre position.

• When a tape is played back for a long period,

the cassette may become warm because of

the built-in power amplifier. However, this is

not a sign of malfunction.

If you have any questions or problems

concerning your unit that are not covered in

this manual, please consult your nearest Sony

dealer.

To maintain high quality sound

If you have drink holders near your audio

equipment, be careful not to splash juice or

other soft drinks onto the car audio. Sugary

residues on this unit or cassette tapes may

contaminate the playback heads, reduce the

sound quality, or prevent sound reproduction

altogether.

Cassette cleaning kits cannot remove sugar

from the tape heads.

Notes on Cassettes

Cassette care

• Do not touch the tape surface of a cassette, as

any dirt or dust will contaminate the heads.

• Keep cassettes away from equipment with

built-in magnets such as speakers and

amplifiers, as erasure or distortion on the

recorded tape could occur.

• Do not expose cassettes to direct sunlight,

extremely cold temperatures, or moisture.

• Slack in the tape may cause the tape to be

caught in the machine. Before you insert the

tape, use a pencil or similar object to turn the

reel and take up any slack.

• Distorted cassettes and loose labels can cause

problems when inserting or ejecting tapes.

Remove or replace loose labels.

• The sound may become distorted while

playing the cassette. The cassette player head

should be cleaned after each 50 hours of use.

Cassettes longer than 90 minutes

The use of cassettes longer than 90 minutes is

not recommended except for long continuous

play. The tape used for these cassettes is very

thin and tends to stretch easily. Frequent

playing and stopping of these tapes may cause

them to become entangled in the cassette deck

mechanism.

Slack

Table of Contents

Location of controls ................................................. 4

Getting Started

Resetting the unit ................................................ 5

Detaching the front panel .................................. 5

Setting the clock .................................................. 6

Cassette Player

Listening to a tape ............................................... 6

Radio reception during fast-forwarding or

rewinding of a tape

— Automatic Tuner Activation (ATA) ........ 7

Radio

Memorizing stations automatically

— Best Tuning Memory (BTM) .................... 7

Memorizing only the desired stations ............. 8

Receiving the memorized stations.................... 8

RDS

Overview of the RDS function .......................... 9

Displaying the station name .............................. 9

Retuning the same programme automatically

— Alternative Frequencies (AF) .................. 9

Listening to traffic announcements .................11

Presetting the RDS stations with the AF and

TA data .......................................................... 12

Locating a station by programme type .......... 12

Setting the clock automatically ....................... 13

Other Functions

Adjusting the sound characteristics ............... 14

Attenuating the sound ..................................... 14

Changing the sound and display settings ..... 14

Boosting the bass sound

— D-bass ....................................................... 15

Selecting the sound position

— “My Best sound Position” ..................... 15

Additional Information

Maintenance....................................................... 16

Dismounting the unit ....................................... 17

Specifications ..................................................... 17

Troubleshooting guide ..................................... 18

Location of controls

Refer to the pages listed for details.

1 Volume +/– button 6

2 MODE button

During radio reception:

BAND select 7, 8

3 TUNER button 7, 8

4 SEL (select) button 6, 13, 14, 15

5 Z (eject) button 6, 7, 8

6 Display window

7 m/M (fast winding)/DIR (tape

transport direction change) buttons 6, 7

8 MBP (My Best sound Position) button

9 D-BASS button 15

q; SEEK/MANU +/– button 8, 10, 13

qa RELEASE (front panel release) button

5, 16

qs ATT (attenuate) button 14

qd SENS/BTM button 7, 8, 12

qf RESET button (located on the front side

of the unit behind the front panel) 5

qg AF button 9, 10, 12

qh Number buttons 7, 8, 13, 14

During radio reception:

Preset number select 8, 10, 12

During tape playback:

(6) ATA 7

qj TA button 11, 12

qk PTY (programme type) button 13

ql DSPL (display mode change) button

6, 9

w; OFF button* 5

* Warning when installing in a car

without ACC (accessory) position on

the ignition key switch

Be sure to press (OFF) on the unit for two

seconds to turn off the clock display after

turning off the engine.

When you press (OFF) momentarily, the

clock display does not turn off and this

causes battery wear.

SENS

AF12 3456TA

PTY DSPL

BTM

AT T

RELEASE

DIR

SEEK

MANU

SEL

MODE

TUNER

D-BASS

OFF

MBP

ATA

XR-L240

Attaching the front panel

Attach part A of the front panel to part B of

the unit as illustrated and push the left side

into position until it clicks.

Notes

• Be sure not to attach the front panel upside

down.

• Do not press the front panel too hard against the

unit when attaching it.

• Do not press too hard or put excessive pressure

on the display window of the front panel.

• Do not expose the front panel to direct sunlight

or heat sources such as hot air ducts, and do not

leave it in a humid place. Never leave it on the

dashboard of a car parked in direct sunlight or

where there may be a considerable rise in

temperature.

Caution alarm

If you turn the car ignition off without

removing the front panel, the caution alarm

will beep for a few seconds.

If you connect an optional power amplifier and

do not use the built-in amplifier, the beep

sound will be deactivated.

Getting Started

Resetting the unit

Before operating the unit for the first time or

after replacing the car battery, you must reset

the unit.

Remove the front panel and press the RESET

button with a pointed object, such as a

ballpoint pen.

Note

Pressing the RESET button will erase the clock

setting and some memorized functions.

Detaching the front panel

You can detach the front panel of this unit to

protect the unit from being stolen.

1 Press (OFF).

2 Press (RELEASE), then slide the front

panel a little to the left, and pull it off

towards you.

Notes

• Be sure not to drop the panel when detaching it

from the unit.

• If you detach the panel while the unit is still

turned on, the power will turn off automatically

to prevent the speakers from being damaged.

• When carrying the front panel with you, use the

supplied front panel case.

RESET button

(OFF)

(RELEASE)

Cassette Player

Listening to a tape

Insert a cassette.

Playback starts automatically.

The side facing up is played.

The side facing down is played.

Tip

To change the tape‘s playback direction, press m

and M.

To stop playback and eject the

cassette

Press Z.

Fast-winding the tape

During playback, press m or M.

* The indicator will flash while fast-winding the

tape.

To start playback during fast-forwarding or

rewinding, press the other fast-winding button

partially until the locked button is released.

Setting the clock

The clock uses a 24-hour digital indication.

Example: To set the clock to 10:08

1 Press (DSPL) for two seconds.

The hour indication flashes.

1 Press either side of the volume button

to set the hour.

2 Press (SEL).

The minute indication flashes.

3 Press either side of the volume button

to set the minute.

2 Press (DSPL).

The clock starts.

After the clock setting is complete, the

display returns to normal playback mode.

To rewind

Direction

indicator*

FWD

REV

To advance

to go forward

to go back

to go forward

to go back

Radio

Memorizing stations

automatically

— Best Tuning Memory (BTM)

The unit selects the stations with the strongest

signals and memorizes them in the order of

their frequencies. You can store up to 6 stations

on each band (FM1, FM2, FM3, MW, and LW).

Caution

When tuning in stations while driving, use

Best Tuning Memory to prevent accidents.

1 Press (TUNER).

In case of tape playback, press Z to eject the

tape.

2 Press (MODE) repeatedly to select the

band.

Each time you press (MODE), the band

changes as follows:

B FM1 B FM2 B FM3 B MW B LW

3 Press (SENS) (BTM) for two seconds.

The unit stores stations in the order of their

frequencies on the number buttons.

A beep sounds when the setting is stored.

Notes

• The unit does not store stations with weak

signals. If only a few stations can be received,

some number buttons will retain their former

setting.

• When a number is indicated in the display, the

unit starts storing stations from the one currently

displayed.

Radio reception during

fast-forwarding or

rewinding of a tape

— Automatic Tuner Activation (ATA)

When fast-forwarding or rewinding with the

m or M button, the tuner will turn on

automatically.

During playback, press (6) (ATA)

repeatedly until “ATA-ON” in the display

appears.

ATA-ON y ATA-OFF

ATA mode starts.

To return to normal playback mode, select

“ATA-OFF.”

AF123456TA

ATA

Memorizing only the

desired stations

You can preset up to 18 FM stations (6 each for

FM1, 2, and 3), up to 6 MW stations, and up to

6 LW stations in the order of your choice.

1 Press (TUNER).

In case of tape playback, press Z to eject the

tape.

2 Press (MODE) repeatedly to select the

band.

3 Press either side of (SEEK/MANU) to tune

in the station that you want to store on

the number button.

4 Press the desired number button ((1) to

(6)) until “MEM” appears.

The number button indication appears in

the display.

Note

If you try to store another station on the same

number button, the previously stored station will

be erased.

Receiving the memorized

stations

1 Press (TUNER).

In case of tape playback, press Z to eject the

tape.

2 Press (MODE) repeatedly to select the

band.

3 Press the number button ((1) to (6)) on

which the desired station is stored.

If you cannot tune in a preset

station

— Automatic tuning/ Local Seek Mode

Automatic tuning:

Press either side of (SEEK/MANU) to

search for the station.

Scanning stops when the unit receives a

station. Press either side of (SEEK/MANU)

repeatedly until the desired station is

received.

Local Seek Mode:

If the automatic tuning stops too

frequently, press (SENS) repeatedly until

“LOCAL-ON” appears.

“LCL” indicator is displayed.

Only the stations with relatively strong

signals will be tuned in.

Tip

If you know the frequency of the station you want

to listen to, press either side of (SEEK/MANU) until

the desired frequency appears (manual tuning).

If FM stereo reception is poor

— Monaural Mode

During radio reception, press (SENS)

repeatedly until “MONO-ON” appears.

“MONO” indicator is displayed.

The sound improves, but becomes

monaural (“ST” disappears).

To return to normal mode, select “MONO-

OFF.”

RDS

Overview of the RDS

function

Radio Data System (RDS) is a broadcasting

service that allows FM stations to send

additional digital information along with the

regular radio programme signal. Your car

stereo offers you a variety of services. Here are

just a few: retuning the same programme

automatically, listening to traffic

announcements, and locating a station by

programme type.

Notes

• Depending on the country or region, not all of

the RDS functions are available.

• RDS may not work properly if the signal strength

is weak or if the station you are tuned to is not

transmitting RDS data.

Displaying the station

name

The name of the current station lights up in the

display.

Select an FM station (page 7).

When you tune in an FM station that

transmits RDS data, the station name

appears in the display.

Note

The “*” indication means that an RDS station is

being received.

Changing the display item

Each time you press (DSPL), the item changes

as follows:

Station Name* (Frequency) y Clock

* When you tune in an FM station that transmits

RDS data, the station name appears.

Note

“NO NAME” appears if the received station does

not transmit RDS data.

Retuning the same

programme automatically

— Alternative Frequencies (AF)

The Alternative Frequencies (AF) function

automatically selects and retunes the station

with the strongest signal in a network. By

using this function, you can continuously

listen to the same programme during a long-

distance drive without having to retune the

station manually.

1 Select an FM station (page 7).

2 Press (AF) repeatedly until “AF-ON”

appears.

The unit starts searching for an alternative

station with a stronger signal in the same

network.

Note

When there is no alternative station in the area

and you do not need to search for an alternative

station, turn the AF function off by pressing (AF)

repeatedly until “AF-OFF” appears.

continue to next page t

102.5MHz

96.0MHz

Frequencies change automatically.

Station

98.5MHz

Changing the display item

Each time you press (AF), the item changes as

follows:

AF-ON y AF-OFF

Notes

• When “NO AF” and the station name flash

alternately, it means that the unit cannot find an

alternative station in the network.

• If the station name starts flashing after selecting

a station with the AF function on, this indicates

that no alternative frequency is available. Press

either side of (SEEK/MANU) while the station

name is flashing (within eight seconds). The unit

starts searching for another frequency with the

same PI (Programme Identification) data (“PI

SEEK” appears and no sound is heard). If the unit

cannot find another frequency, “NO PI” appears,

and the unit returns to the previously selected

frequency.

Listening to a regional programme

The “REG-ON” (regional on) function lets you

stay tuned to a regional programme without

being switched to another regional station.

(Note that you must turn the AF function on.)

The unit is factory preset to “REG-ON,” but if

you want to turn off the function, do the

following.

During radio reception, press (AF) for

two seconds until “REG-OFF” appears.

Note that selecting “REG-OFF” might cause

the unit to switch to another regional

station within the same network.

To return to regional on, select “REG-ON.”

Note

This function does not work in the United

Kingdom and in some other areas.

Changing the display item

Each time you press (AF) for two seconds, the

item changes as follows:

REG-ON y REG-OFF

Local link function

(United Kingdom only)

The Local Link function lets you select other

local stations in the area, even if they are not

stored on your number buttons.

1 Press a number button that has a local

station stored on it.

2 Within five seconds, press the number

button of the local station again.

3 Repeat this procedure until the desired

local station is received.

Presetting the volume of traffic

announcements

You can preset the volume level of the traffic

announcements beforehand so you won’t

miss the announcement. When a traffic

announcement starts, the volume will be

automatically adjusted to the preset level.

1 Press the volume button to adjust the

desired volume level.

2 Press (TA) for two seconds.

“TA” appears and the setting is stored.

Receiving emergency

announcements

If an emergency announcement comes in while

you are listening to the radio, the programme

will automatically switch to it. If you are

listening to a source other than the radio, the

emergency announcements will be heard if

you set AF or TA to on. The unit will then

automatically switch to these announcements

no matter which source you are listening to at

the time.

Listening to traffic

announcements

The Traffic Announcement (TA) and Traffic

Programme (TP) data let you automatically

tune in an FM station that is broadcasting

traffic announcements even if you are listening

to other programme sources.

Press (TA) repeatedly until “TA-ON”

appears.

The unit starts searching for traffic

information stations. “TP” appears in the

display when the unit finds a station

broadcasting traffic announcements.

When the traffic announcement starts,

“TA” flashes. The flashing stops when the

traffic announcement is over.

Tip

If the traffic announcement starts while you are

listening to another programme source, the unit

automatically switches to the announcement and

goes back to the original source when the

announcement is over.

Notes

•

“NO TP” flashes for five seconds if the received

station does not broadcast traffic announcements.

Then, the unit starts searching for a station that

broadcasts it.

• When “EON” appears with “TP” in the display,

the current station makes use of broadcast traffic

announcements by other stations in the same

network.

To cancel the current traffic

announcement

Press (TA).

To cancel all traffic announcements, turn off

the function by pressing (TA) until

“TA-OFF” appears.

Presetting the RDS

stations with the AF and

TA data

When you preset RDS stations, the unit stores

each station’s data as well as its frequency, so

you don’t have to turn on the AF or TA

function every time you tune in the preset

station. You can select a different setting (AF,

TA, or both) for individual preset stations, or

the same setting for all preset stations.

Presetting the same setting for all

preset stations

1 Select an FM band (page 7).

2 Press (AF) and/or (TA) to select “AF-ON”

and/or “TA-ON.”

Note that selecting “AF-OFF” or “TA-OFF”

stores not only RDS stations, but also non-

RDS stations.

3 Press (SENS) (BTM) until “BTM” flashes.

Presetting different settings for

each preset station

1 Select an FM band, and tune in the

desired station.

2 Press (AF) and/or (TA) to select “AF-ON”

and/or “TA-ON.”

3 Press the desired number button until

“MEM” appears.

Repeat from step 1 to preset other stations.

Tip

If you want to change the preset AF and/or TA

setting after you tune in the preset station, you

can do so by turning the AF or TA function on or

off.

Locating a station by

programme type

You can locate the station you want by

selecting one of the programme types shown

below.

Programme types Display

News NEWS

Current Affairs AFFAIRS

Information INFO

Sports SPORT

Education EDUCATE

Drama DRAMA

Culture CULTURE

Science SCIENCE

Varied VARIED

Popular Music POP M

Rock Music ROCK M

Easy Listening EASY M

Light Classical LIGHT M

Classical CLASSICS

Other Music Type OTHER M

Weather WEATHER

Finance FINANCE

Children’s Programmes CHILDREN

Social Affairs SOCIAL A

Religion RELIGION

Phone In PHONE IN

Travel TRAVEL

Leisure LEISURE

Jazz Music JAZZ

Country Music COUNTRY

National Music NATION M

Oldies Music OLDIES

Folk Music FOLK M

Documentary DOCUMENT

Not specified NONE

Note

You cannot use this function in some countries

where no PTY (Programme Type selection) data is

available.

Setting the clock

automatically

The CT (Clock Time) data from the RDS

transmission sets the clock automatically.

1 During radio reception, press (SEL) and

(2) simultaneously.

2 Press (2) repeatedly until

“CT-ON” appears.

The clock is set.

In two seconds the normal display

automatically appears.

To cancel the CT function

Select “CT-OFF” in step 2.

Notes

• The CT function may not work even though an

RDS station is being received.

• There might be a difference between the time

set by the CT function and the actual time.

1 Press (PTY) during FM reception.

The current programme type name appears

if the station is transmitting the PTY data.

“- - - - -” appears if the received station is

not an RDS station, or if the RDS data has

not been received.

If the TA function is ON, the unit starts

searching for the next station.

2 Press (PTY) repeatedly until the desired

programme type appears.

The programme types appear in the order

shown in the above table. Note that you

cannot select “NONE” (Not specified) for

searching.

3 Press either side of (SEEK/MANU).

The unit starts searching for a station

broadcasting the selected programme type.

When the unit finds the programme, the

programme type appears again for five

seconds.

“NO” and the programme type appear

alternately for five seconds if the unit

cannot find the programme type. It then

returns to the previously selected station.

Other Functions

Adjusting the sound

characteristics

You can adjust the bass, treble, balance, and

fader.

You can store the bass and treble levels

independently for each source.

1 Select the item you want to adjust by

pressing (SEL) repeatedly.

Each time you press (SEL), the item

changes as follows:

BAS (bass) t TRE (treble) t

BAL (left-right) t FAD (front-rear)

2 Adjust the selected item by pressing

either side of the volume button.

Adjust within three seconds after selecting

the item.

Attenuating the sound

Press (ATT).

After “ATT-ON” momentarily flashes, the

“ATT” indication appears in the display.

To restore the previous volume level, press

(ATT) again.

“ATT-OFF” flashes momentarily.

Changing the sound and

display settings

The following items can be set:

•CT (Clock Time) (page 13).

•M.DSPL (Motion Display)

– the demonstration mode which appears

when the tape is ejected and no source is

selected (e.g., tuner is turned off).

•BEEP – to turn the beep sound on or off.

1 Press (SEL).

2 Press the preset number button to select

the desired item.

Number buttons

(2): CT

(4): M.DSPL

(6): BEEP

Note

The displayed item will differ depending on the

source.

3 Press the preset number button

repeatedly to select the desired setting

(Example: ON or OFF).

0dB

D.BASS-3

D.BASS-2

D.BASS-1

D.BASS-3

D.BASS-2

D.BASS-1

Boosting the bass sound

— D-bass

You can enjoy a clear and powerful bass

sound. The D-bass function boosts the low

frequency signal and high frequency signal

with a sharper curve than conventional bass

boost.

You can hear the bass line more clearly even

while the vocal volume remains the same. You

can emphasize and adjust the bass sound

easily with the D-BASS button.

Adjusting the bass curve

Press (D-BASS) repeatedly to select the

desired bass curve.

As the D-BASS number increases so does

the effect.

D.BASS-1 t D.BASS-2 t D.BASS-3 t

D.BASS-OFF

Note

The bass sound may distort at same volume. If the

bass sound distorts, select less effective bass curve.

Level

Frequency (Hz)

Selecting the sound

position — “My Best sound Position”

When you drive without passengers, you can

enjoy comfortable sound environment by “My

Best sound Position.”

“My Best sound Position” has two presets,

which adjusts the sound level of balance and

fader. You can select one very easily with MBP

button.

Press (MBP) repeatedly until the desired

listening position.

Mode of “My Best sound Position” will be

shown in the display in order of the table.

After one second, the display goes back to

the normal playback mode.

If you want to adjust the sound level of

balance and fader more precisely, you can

do it in (SEL) button. (See “Adjusting the

sound characteristics” on page 14.)

Display

window

MBP-A

MBP-B

MBP-OFF

Right

– 4dB

Left

– 4dB

Front

Rear

– 4dB

Balance Level

Fader Level

Fuse (10 A)

Additional

Information

Maintenance

Fuse replacement

When replacing the fuse, be sure to use one

matching the amperage rating stated on the

original fuse. If the fuse blows, check the

power connection and replace the fuse. If the

fuse blows again after replacement, there may

be an internal malfunction. In such a case,

consult your nearest Sony dealer.

Warning

Never use a fuse with an amperage rating

exceeding the one supplied with the unit as

this could damage the unit.

Cleaning the connectors

The unit may not function properly if the

connectors between the unit and the front

panel are not clean. In order to prevent this,

open the front panel by pressing (RELEASE),

then detach it and clean the connectors with a

cotton swab dipped in alcohol. Do not apply

too much force. Otherwise, the connectors may

be damaged.

Main unit

Back of the front panel

Notes

• For safety, turn off the engine before cleaning

the connectors and remove the key from the

ignition switch.

• Never touch the connectors directly with your

fingers or any metal device.

Dismounting the unit

Release key (supplied)

Specifications

Cassette player section

Tape track 4-track 2-channel stereo

Wow and flutter 0.13 % (WRMS)

Frequency response 30 – 15,000 Hz

Signal-to-noise ratio 55 dB

Tuner section

Tuning range 87.5 – 108.0 MHz

Aerial terminal External aerial connector

Intermediate frequency 10.7 MHz

Usable sensitivity 11 dBf

Selectivity 75 dB at 400 kHz

Signal-to-noise ratio 62 dB (stereo),

68 dB (mono)

Harmonic distortion at 1 kHz

0.7 % (stereo),

0.5 % (mono)

Separation 33 dB at 1 kHz

Frequency response 30 – 15,000 Hz

MW/LW

Tuning range MW: 531 – 1,602 kHz

LW: 153 – 279 kHz

Aerial terminal External aerial connector

Intermediate frequency 10.7 MHz/450 kHz

Sensitivity MW: 30 µV

LW: 50 µV

Power amplifier section

Outputs Speaker outputs

(sure seal connectors)

Speaker impedance 4 – 8 ohms

Maximum power output 45 W × 4 (at 4 ohms)

General

Outputs Power aerial relay control

lead

Tone controls Bass ±9 dB at 100 Hz

Treble ±9 dB at 10 kHz

Power requirements 12 V DC car battery

(negative earth)

Dimensions Approx. 178 × 50 × 178 mm

(w/h/d)

Mounting dimensions Approx. 182 × 53 × 161 mm

(w/h/d)

Mass Approx. 1.2 kg

Supplied accessories Parts for installation and

connections (1 set)

Front panel case (1)

Design and specifications are subject to change

without notice.

Troubleshooting guide

The following checklist will help you remedy the problems you may encounter with your unit.

Before going through the checklist below, check the connections and operating procedures.

General

Tape playback

Problem

The sound is distorted.

Cause/Solution

The tape head is contaminated.

t Clean the head with a commercially available dry-type

cleaning cassette.

Radio reception

Problem

Preset tuning is not possible.

Automatic tuning is not

possible.

The stations cannot be

received.

The sound is hampered by

noises.

The “ST” indication flashes.

Cause/Solution

• Store the correct frequency in the memory.

• The broadcast signal is too weak.

•The broadcast signal is too weak.

t Use manual tuning.

•The local seek mode is set to ON.

t Set the local seek mode to OFF (page 8).

Connect an power aerial control lead (blue) or accessory power

supply lead (red) to the power supply lead of a car’s aerial

booster. (When your car has built-in FM/MW/LW aerial in the

rear/side glass only.)

•Tune in the frequency accurately.

•The broadcast signal is too weak.

t Set to MONO mode (page 8).

Problem

No sound.

The contents of the memory

have been erased.

Indications do not appear

in the display.

Cause/Solution

•Cancel the ATT function (page 14).

•Set the fader control to the centre position for two-speaker

systems.

•Adjust the volume with (+).

• The power cord or battery has been disconnected.

• The RESET button was pressed.

t Store again into the memory.

Remove the front panel and clean the connectors. See

“Cleaning the connectors” (page 16) for details.

RDS

Problem

The SEEK starts after a few

seconds of listening.

No traffic announcements.

PTY displays “NONE.”

Cause/Solution

The station is non-TP or has a weak signal.

t Press (AF) or (TA) repeatedly until “AF-OFF” or

“TA-OFF” appears.

•Activate “TA.”

•The station does not broadcast any traffic announcements

despite being TP.

t Tune to another station.

The station does not specify the programme type.

If the above-mentioned solutions do not help improve the situation, consult your nearest Sony

dealer.

Danke, daß Sie sich für dieses

Autokassettenradio von Sony entschieden

haben.

Sicherheitsmaßnahmen

•Wenn Sie Ihr Auto direkt in der Sonne

geparkt haben und die Temperatur im

Wageninneren sehr hoch ist, lassen Sie das

Gerät zunächst etwas abkühlen, bevor Sie es

benutzen.

•Wenn die Stromversorgung des Geräts

unterbrochen ist, überprüfen Sie zunächst die

Anschlüsse. Sind diese in Ordnung,

überprüfen Sie die Sicherung.

•Wenn bei einem Zwei-Lautsprecher-System

über diese Lautsprecher kein Ton

ausgegeben wird, stellen Sie den Fader-

Regler in die mittlere Position.

•Wenn die Kassette längere Zeit

wiedergegeben wird, kann sie sich aufgrund

des integrierten Endverstärkers erwärmen.

Dabei handelt es sich jedoch nicht um eine

Fehlfunktion.

Wenn Sie Fragen haben oder an Ihrem Gerät

Probleme auftauchen, die in dieser

Bedienungsanleitung nicht behandelt werden,

wenden Sie sich bitte an Ihren Sony-Händler.

So vermeiden Sie eine

Verringerung der Klangqualität

Ist neben der Autostereoanlage ein

Getränkehalter angebracht, so achten Sie

darauf, keine Säfte oder andere zuckerhaltige

Getränke auf die Anlage zu verschütten.

Zuckerrückstände in der Anlage oder auf den

Kassettenbändern können die

Wiedergabeköpfe verschmutzen, zu einer

verringerten Klangqualität führen oder die

Wiedergabe ganz unmöglich machen.

Zuckerrückstände lassen sich auch mit

Reinigungskassetten nicht von den Tonköpfen

entfernen.

Willkommen! Umgang mit Kassetten

Pflege von Kassetten

•Berühren Sie nicht das Band in einer

Kassette. Andernfalls lagern sich Schmutz-

oder Staubpartikel auf den Tonköpfen ab.

•Halten Sie Kassetten von Geräten mit

eingebauten Magneten, zum Beispiel

Lautsprechern und Verstärkern, fern.

Andernfalls kann die Aufnahme auf dem

Band gelöscht oder beschädigt werden.

•Setzen Sie Kassetten weder direktem

Sonnenlicht noch großer Kälte oder

Feuchtigkeit aus.

•Wenn das Band nicht gespannt ist, kann es

sich im Gerät verfangen. Straffen Sie deshalb

vor dem Einlegen einer Kassette das Band,

indem Sie die Spule mit einem Stift oder

einem ähnlichen Gegenstand drehen.

•Beschädigte Kassetten und lose Aufkleber

können beim Einlegen oder Auswerfen von

Kassetten Probleme verursachen. Entfernen

Sie lose Aufkleber, oder tauschen Sie sie aus.

• Während der Wiedergabe der Kassette kann

es vorkommen, daß der Ton verzerrt ist. Der

Tonkopf des Kassettenrecorders sollte nach

jeweils 50 Gebrauchsstunden gereinigt

werden.

Nicht

gespannt

La page charge ...

Sony XR-L240 Manuel utilisateur

Marque: Sony

Modèle: XR-L240

Catégorie: Récepteurs multimédia de voiture

Taper: Manuel utilisateur

Télécharger le PDF

rapport

Sony XR-L240 Manuel utilisateur

Sony XR-L240 Manuel utilisateur

dans d''autres langues

Documents connexes