Viking Plug-n-Play Spas Series Le manuel du propriétaire

Owner’s Manual

V 1 0 0

V 3 0 0 / V 5 0 0

2014

TABLE OF CONTENTS

• Important Safety Instructions 2

Personal Safety Precautions 4

Installation and Set-Up Instructions 5

Electrical Requirements (VS-300) 5

• Spa Startup Directions 6

Apply Power 7

Electrical Specifications 7

• Operation Instructions 8

Activate Water Pump 8

Power System Features 9

Topside Control Instructions 10

Topside Functions 11

Diagnostic Messages 12

Spa Jets and Air Controls 14

• Maintenance 15

Skimmer Side Filter 15

Add Start-Up Chemicals 15

Spa Draining 16

Spa Surface Care 16

Long-Term Storage 16

Vika-Shield Cabinet 17

Filter Cleaning 17

• Ozonator 18

• Spa Situations & Solutions 19

• Trouble Shooting 20

1

IMPORTANT SAFETY INSTRUCTIONS

When installing and using this electrical equipment, basic safety pre-

cautions should always be followed, including the following:

READ AND FOLLOW

ALL INSTRUCTIONS

1. WARNING: To reduce the risk of injury, do not permit

children to use this product unless they are closely supervised

at all times. Keep spa cover locked when not in use.

2. A wire connector is provided on this unit to connect a minimum

No. 8 AWG (8.4mm2) solid copper conductor between this

unit and any metal equipment, metal water pipe or conduit

within 5 feet (1.5m) of the unit.

3. DANGER: Risk of Injury. The suction fittings in this spa are

sized to match the specific water flow created by the pump.

Should the need arise to replace the suction fittings or the

pump, be sure that the flow rates are compatible. Never

operate the spa if the suction fittings are broken or missing.

Never replace a suction fitting with one rated less than the flow

rate marked on the original fitting.

4. DANGER: Risk of Accidental Drowning. Extreme Caution

must be exercised to prevent unauthorized access by children.

To avoid accidents, insure that children cannot use this spa

unless they are supervised at all times.

5. DANGER: Risk of Electric Shock. Install at least 5 feet (1.5m)

from all metal surfaces. As an alternative, a spa may be

installed within 5 feet of metal surfaces if each metal surface is

permanently connected by a minimum No. 8 AWG (8.4mm2)

solid copper conductor to the wire connector on the terminal

box that is provided for this purpose.

6. DANGER: Risk of Electric Shock. Do not permit any

2

electrical appliance, such as a light, telephone, radio or

television within 5 feet (1.5m) of a spa.

7. WARNING: To Reduce the Risk of Injury:

a) Before using your spa you should check the water

temperature with a thermometer that is known to be

accurate. The water temperature in a spa should never

exceed 104°F (40°C). A water temperature of 104°F is

considered safe for a healthy adult. Lower water

temperatures are recommended for young children and

when spa use exceeds 10 minutes.

b) Since excessive water temperatures have a high potential for

causing fetal injury during the early months of pregnancy,

pregnant or possibly pregnant women should limit spa water

temperature to 100°F (38°C).

c) The use of alcohol, drugs, or medication before or during

spa use may lead to unconsciousness with the possibility of

drowning.

d) Persons suffering from obesity or with a medical history of

heart disease, low or high blood pressure, circulatory

system problems or diabetes should consult a physician

before using a spa.

e) Persons using medication should consult a physician before

using a spa since some medication may induce drowsiness

while other medications may affect heart rate, blood

pressure and circulation.

8. The causes, symptoms and affects of hyperthermia may be

described as follows:

Hyperthermia occurs when the internal temperature of the body

reaches a level several degrees above the normal temperature

of 98.6°F. The symptoms of hyperthermia include an increase

in the internal temperature of the body, dizziness, lethargy,

drowsiness and fainting.

The effects of hyperthermia include:

• Failure to feel heat

• Failure to recognize the need to exit the spa

• Unawareness of impending hazards

3

• Fetal injury in pregnant women

• Physical inability to exit the spa or hot tub

• Unconsciousness resulting in the potential of drowning

9. WARNING: The use of alcohol, drugs or medication can

greatly increase the risk of fatal hyperthermia. If you suspect

hyperthermia, immediately get medical help, lay the victim on

their back with the head slightly elevated for easier breathing,

cover the body with a blanket and apply ice packs to the

head.

10. Never touch or come in contact with any electrical accessory

when in your spa or when your body is wet.

11. Prior to performing any service to the spa pack, turn off ALL

power to the system at the main power source breaker.

NOTE: A READILY ACCESSIBLE DISCONNECTING MEANS

SHALL BE PROVIDED DURING INSTALLATION.

SAVE THESE INSTRUCTIONS

PERSONAL SAFETY PRECAUTIONS

1. Please use the spa when others are present.

2. Children should have spa access only with the permission and

supervision of an adult.

3. To reduce the risk of child drowning, keep the spa filter clean

and unclogged. Do not modify the suction or filtration

systems.

4. Exercise caution when entering or leaving the spa. When

moving or changing positions, be sure of your footing before

applying your full weight as water refraction can be

misleading.

5. Do not stay in the spa for extended periods of time. Set a

reasonable time limit after which you leave the spa, cool

down, take a shower, relax and then return for another stay in

the spa.

4

INSTALLATION AND SET-UP INSTRUCTIONS

SURFACE AND PAD REQUIREMENTS

• Your new portable spa must be placed on a uniformly firm,

flat and level surface. A concrete pad 4 inches thick is

best.

• In order to prevent flooding of the electrical equipment, the

pad must be such that water will drain away from the spa.

• If your spa is located near sprinklers, adjust or cap them so

as not to hit the siding of the spa.

BALCONIES AND DECK REQUIREMENTS

• Decking must be constructed to support 85 pounds per

square ft.

• Balconies must be constructed to meet current state and

local codes.

• Gates must be self-closing and self-latching.

ELECTRICAL REQUIREMENTS (All Models)

• Your 120-volt spa pack comes installed with a 15-amp rated

dedicated G.F.C.I. cord connected device.

• Your 120-volt spa pack is designed to be “PERMANENTLY

CONNECTED”.

• Use of any extension cord is dangerous and is not to be used in

conjunction with the operation of the spa. Low voltage damage

may result and will void your warranty.

• It is the customer’s responsibility to acquire necessary

permits and to arrange for installation and hook up of

the electrical power.

• Your spa comes set up from the factory to accept 120v

ONLY. Any attempt to remove the factory installed GFCI

cord or alter the voltage will result in voiding your

warranty.

5

SPA STARTUP DIRECTIONS

All Viking Spas require a solid, flat surface.* This is to ensure that the

spa cabinet is not exposed to a pressure stress condition that may

result in cabinet damage and shell cracking. A concrete pad is the

best example of a solid, flat surface, however, wood decking is suit-

able, provided it can withstand 85# per sq. ft. without deflection.

* FAILURE TO PROVIDE A PROPER, SOLID, FLAT SURFACE

MAY DAMAGE YOUR SPA AND VOID YOUR WARRANTY.

The following procedure should be followed on initial startup and

whenever the spa is drained for maintenance. Read each step in its

entirety before proceeding with that step.

FILL THE SPA WITH WATER

a. Clear all debris from your spa.

b. Remove filter element.

c. Using a garden hose, place hose in filter chamber for filling.

Do not fill higher than three quarters of the way up the skimmer

opening.

d. We DO NOT recommend the use of softened water due

to the potential harm of damaging equipment.

e. As water level rises, check inside equipment compartments for

water leaks. It may be necessary to tighten loose unions and/or

fittings.

f. Make sure T-Handled Gate VALVES at pump and heater are open.

(Fully extended up position).

6

APPLY POWER

a. Apply power by turning on the spa-dedicated circuit breaker.

b. Test the GFCI: push the TEST button and power is cut off. Push

RESET and power is restored. If these do not seem to work,

STOP! Do not use your spa. There is no power, the

GFCI is defective or the equipment is malfunctioning. Only a

LICENSED ELECTRICIAN should do further inspection.

ELECTRICAL SPECIFICATIONS

GENERAL

NOTICE: All spa electrical wiring must be in accordance

to meet NEC (National Electrical Code) state and local

codes.

Wire gauge must be in accordance with NEC

requirements for the distance from current source to spa and

the current rating as stated on the ID label that is attached to

the equipment control enclosure.

GFCI CIRCUIT BREAKER REQUIREMENTS

The existing electrical outlet must have correct currently rating per local

and state codes to accept GFCI from spa.

Breaker

CAPACITY 15 amps

POLES 2

# WIRES 3

7

OPERATION INSTRUCTIONS

ACTIVATE WATER PUMP

Press the jet button on the control board. The high-speed pump will

come on.

Press the jet button again to turn the water to low speed.

Check for water leaks at unions and/or fittings on your equipment

while pump is running.

POWER SYSTEM FEATURES

The power system is located under the skirt. The equipment can be

serviced by simply removing the access panel screws.

It is very important to make sure that the spa is filled up to the proper

level (note the water level mark on the skimmer face) before operating

spa. Make sure the gate valves are in the open or up position.

WARNING: Do not run spa with gate valves closed or run pump with

no water circulating in spa for long periods. Damage could occur to

the spa equipment.

NOTE: The V100, V300 & V500 spas are 120V Only.

8

V300/V500 FEATURES

The V300/V500 model features a Waterfall jet, which allows the user

to regulate the flow of water to the jet by simply turning the valve for

the waterfall from “off” to “on”. (See illustration below)

9

Regulates Air

into Jets

Waterfall

On/Off Control

V300 in Gray

* To drain the spa, make sure the gate valve is in the Up /

Open position. Remove the cap from the drain and attach

the garden hose. Open the valve by turning the large part of

the drain counterclockwise until it stops. Pull on the drain that

the hose is connected to until you hear it “pop”. Water will

gravity drain through the garden hose. Be sure to close the

drain prior to refilling. Note: the drain will not remove all of

the water in the spa. You may have to remove a small amount

of water by hand.

Water Gate Valve

Drain* for V100

To drain your spa, power must be disconnected at the cir-

cuit breaker. Locate the drain faucet on the corner near the

bottom of the side panel next to the equipment. 1. Twist

cap off and attach a garden hose to the opening. 2. Turn

the outside body counter clockwise until it stops. 3. Pull on

the drain that the hose is connected to until you hear a

“pop”. 4. Drain the spa. 5. Reverse this procedure to shut

the water off. Note: the drain will not remove all of the

water in the spa. You may have to remove a small amount

of water by hand.

Drain* for V300/V500

TOPSIDE CONTROL INSTRUCTIONS

INITIAL START-UP

When your spa is first activated, it will go into Priming mode, indicat-

ed by “Pr”. The priming mode will last for less than 5 minutes. Then,

the spa will begin to heat and maintain the water temperature in the

Standard mode indicated by “St”.

TEMPERATURE (80°F - 104°F / 26°C - 40°C)

The start-up temperature is set at 100°F/37°C. The last temperature is

constantly displayed on the LCD.

Note: The last spa tem peratu re display ed is cu rren t only

w hen the pu m p has been ru n n in g for at least 2 m in u tes

.

Press the “Temp” button to display the temperature previously set. The

set temperature flashes on the display. Pressing the “Temp” button a

second time, while it is still flashing, will cause the set temperature to

increase or decrease depending on what direction was last chosen.

Each press to follow will change the set temperature in the same direc-

tion. If the opposite direction is desired, release the pad and let the

display revert to the actual water temperature. Press the button to dis-

play the set temperature, and press again to make the temperature

change in the desired direction. After three seconds, the LCD will

stop flashing and display the current spa temperature.

10

Heat On

Indicator Light

Turns Light

On/Off

Controls Low

Speed/High Speed Pump

Displays Temperature and

Diagnostic Messages

Sets Water

Temperature

TOPSIDE FUNCTIONS

JETS

Press the “Jets” button once to activate the low speed of the pump and

again for the high speed. Press the “Jets” button again to turn off the

pump. If left running, the low speed of the pump will automatically

turn off after 4 hours, and the high speed will automatically turn off

after 15 minutes.

LIGHT

Press the “Light” button to turn the light on and off. If left on, the light

automatically turns off after 4 hours. For the V300 with LED light

and V500 with LED perimeter lighting, press the light button consecu-

tively to change the color sequencing.

MODE

The mode is changed by pressing the “Temp” button, then pressing the

“Light” button.

Standard Mode is programmed to maintain the desired

temperature. Note that the last measured spa temperature displayed

is current only when the pump has been running for at least 2

minutes. “St” will be displayed momentarily when you switch into

Standard mode.

Economy Mode heats the spa to the set temperature only during

filter cycles. “Ec” will display solid when temperature is not current,

and will alternate with temperature when temperature is current.

Sleep Mode heats the spa to within 20°F/10°C of the set

temperature only during filter cycles. “SL” will display solid

when temperature is not current, and will alternate with temperature

when temperature is current.

Preset Filter Cycles. The first filter cycle begins 6 minutes after

the spa is energized. The second filter cycle begins 12 hours later.

Filter duration is programmable for 1, 2, 3, 4, 5, 6, 7 or 8 hours

indicated by “FC”. The default filter time is 1 hours. To program,

press “Temp,” then “Jets.” Press “Temp” to adjust. Press “Jets” to

exit programming.

NOTE

The pump will activate for 1 to 2 minutes to check temperature every

30 minutes or whenever the set temperature is raised.

11

DIAGNOSTIC MESSAGES

Message Meaning Action Required

_ _ Temperature Unknown After the pump has been

running for 2 minutes, the

temperature will be displayed.

HH “Overheat” – The spa DO NOT ENTER THE WATER.

has shut down. Remove the cover and allow

One of the sensors has water to cool. Reset by pushing

detected 118°F/48°C any button.

at the heater.

OH “Overheat” – The spa DO NOT ENTER THE WATER.

has shut down. One of Remove the spa cover and

the sensors has detected allow the water to cool. At

that the spa water is 107°F/42°C the spa should

110°F/43°C. automatically reset. If it does not,

shut off the power to the spa and

call your dealer or service

organization.

IC “Ice” – Potential freeze No action required. The pump(s)

condition detected. will automatically activate

regardless of spa status.

SA The spa has shut down. If the problem persists, contact

The sensor that is your dealer or service organ-

plugged into the ization. (May appear temporari-

Sensor “A” jack is not ly in an overheat situation and

working. disappear when the heater cools.)

SB The spa has shut down. If the problem persists, contact

The sensor that is your dealer or service organ-

plugged into the ization. (May appear temporari-

Sensor “B” jack is not ly in an overheat situation and

working. disappear when the heater cools.)

Sn Sensors are out of If the problem persists,

1 12

balance. If alternating contact your dealer or service

with spa temp, it may organization.

just be a temporary

condition. If flashing by

itself, spa is shut down.

HL A significant difference Check water level in spa.

between temperature Refill if necessary. If the water

sensors has been level is okay, make sure the

detected. This could pump(s) have been primed.

indicate a flow problem.

LF Persistent low flow Follow action required for “HL”

problems. (Displays

on the fifth occurrence of

HL message within 24 hrs.)

Heater is shut down, but

other spa functions continue

to run normally.

dr Possible inadequate Check water level in spa. If

water, poor flow or water level is okay, make sure

air bubbles detected pump(s) have been primed.

in the heater. Spa Press any button to reset or this

is shut down for 15 message will automatically reset

minutes. within 15 minutes.

dy Inadequate water Follow action required for “dr”

detected in heater. message.

(Displays on third

occurrence of “dr”

message.) Spa is shut

down.

WARNING! / Shock Hazard! / No User Serviceable Parts.

Do not attempt service of this control. Contact your spa retailer

or service organization for assistance. Installation and/or

service must be performed by a licensed electrician

and all grounding connections must be properly installed.

13

SPA JETS AND AIR CONTROLS

SPA JETS

Adjustable Spa Jets may be turned off and on by rotating jet faceplate

left or right.

Note: DO NOT TURN ALL SPA JETS OFF AT THE SAME

TIME. THIS MAY CAUSE DAMAGE TO THE PUMP AND

MOTOR.

AIR CONTROLS

Air controls are adjusted by rotating the topside dial. These controls

serve to regulate the amount of air mixed with water when the whirlpool

or hydrotherapy jets are operating in the high pump mode.

3 14

Directional Adjustable Poly Storm

Directional Mini Storm

Directional Cluster

V300/V500

V100

MAINTENANCE

SKIMMER SIDE FILTER

All Viking spas have a skimmer side filter that does not require “air

bleeding” on initial startup. If an air lock develops, loosen the union

on return side of pump. Let small amount of water drain from connec-

tion while the pump is running. Once the water begins to flow out of

the jets retighten the union.

Clean spa filters are critical for proper operation. Dirty filters cause

water restriction to the pump, which in turn may cause erratic heating

of the spa. A starving pump will degrade performance, result in dirty

or murky water and may cause the heater to malfunction.

ADD START-UP CHEMICALS

Ask your spa retailer to HELP you set up a chemical maintenance program.

The importance of chemical balance in your spa cannot be overem-

phasized.

SANITIZING: Please refer to your dealer supplied sanitizing recom-

mendations for your start up procedures.

NOTE: If you live in an area where city water is not available, or

your spa water shows signs of calcium content, you will need to add a

“stain n scale” chemical on initial fill and then once a week, thereafter.

15

SPA DRAINING

Every 3 to 4 months, depending upon water condition, you may

need to renew the spa water. To drain your spa, power must be

disconnected at the circuit breaker. Locate the drain faucet within

the equipment access compartment. Attach a garden hose to the

faucet and then open it. Water will start draining. The drain spigot

will not remove all of the water in the spa. You may have to remove

a small amount of water by hand.

SPA SURFACE CARE

Do not use abrasive solvents or cleaners to clean spa surfaces.

Consult your Viking Spa Retailer for the proper cleaners and detergents.

LONG-TERM STORAGE (90 days or more)

If you are not going to use your spa for an extended period of time, drain

it as described above. You will also have to drain the pump. Water left in

the spa during long-term storage may cause freeze damage.*

To drain the pump, remove drain plug from the face of the pump.

Reinstall drain plug before using spa once again.

Additional water removal is required to prevent freeze damage to the

spa plumbing assembly. Use of a wet/dry vac is required. Place the

shop vac hose over each individual jet and vacuum up any excess

water out. Place the shop vac on the Suction fitting(s) and vacuum any

excess water. This will eliminate the entrapment of water in the plumb-

ing lines that could freeze and cause damage.

NOTE: We also recommend vacuuming each jet opening to ensure

that all of the water is out of the plumbing lines.

*FREEZE DAMAGE TO THE SPA PLUMBING IS NOT COVERED

UNDER THE WARRANTY.

16

SPA CABINET

All Viking spas have a standard synthetic wood cabinet. This material

is virtually maintenance free and does not require any type of sealant

or treatment.

FILTER CLEANING

Your filter should be replaced once a year. When filters are removed

from the spa, make sure that no objects fall into the filter cavity. They

can cause obstruction to water movement. Remove filter cartridges as

shown in figure below.

The filter must be cleaned every 2 months, more often with heavy use,

to get rid of objects and particles that are lodged in the filter pleats.

Using a garden hose with a pressurized nozzle, push water from the

inside to the outside of the filter pleats forcing all trapped particles out.

If the filter is too dirty to be cleaned as described above, obtain filter

cleaner material from your Viking Spa Retailer. Soak the filter

overnight; then hose it down.

A. Locate skimmer. B. Pull weir door open.

C. Remove basket. D. Remove the two separate filters

and follow cleaning instructions above.

17

OZONATOR

If your spa is equipped with an ozonator, it is factory set to filter dur-

ing the filter cycles only. We recommend the F4 setting which means

your spa will filter a total of 8 hours (4 hours twice a day). This should

provide adequate ozonation, provided there is proper chemical bal-

ance in the spa.

NOTE: Please Do Not attempt to disassemble ozonator if it becomes

inoperable. Ozonators contain no user serviceable parts. Please con-

tact your spa retailer or service organization.

7 18

Situation Cause or Result Product to use Solution

Calcium deposits Hard water Stain n Scale Add 1oz. of Stain n Scale

on surfaces of

heater, fittings pH/total alkalinity pH Up Test water - adjust with

or plumbing out of adjustment pH Down pH Up or pH Down. For

preventative maintenance

add Stain n Scale weekly.

(1oz. up to 300 gals.)

Cloudy or murky pH/total alkalinity pH Up Test water - add pH Up or

water out of balance pH Down pH Down as needed

Plugged filter Spa Cartridge Filter Use Spa Cartridge Filter

Cleaner Cleaner (min. once/month)

No sanitizer residual Chlorinating Granules Add Chlorinating or

Brominating Granules (no

more than 2oz. per treatment).

Oils, soap, foreign Spa See Clear Treat water with Spa See

matter & other Clear twice a week (1oz.

contaminants up to 300 gals.)

Too many conflicting Drain & refill if water is

chemicals older than 60 days

Eye & skin Water balance needs pH Up Test water, add pH Up, pH

irritation, rashes to be corrected (pH/ pH Down Down or Total “A” as needed

allergies total alkalinity) Total “A”

Excessive chlorine or Add fresh water and/or wait

bromine a day & re-test sanitizer level

Excessive foam Build up of body oils, Spa Foam Away Add Spa Foam Away to

cosmetics and Spa See Clear foamy area, then add 1oz.

contaminants Spa See Clear

pH/Total Alkalinity Spa See Clear Add Spa See Clear or Spa

not in balance or Spa Stain n Scale Stain n Scale to help remove

calcium level too low oils and contaminants

Soft water Drain and refill.

Blue water Copper metals in Cop-Out Use Cop-Out as per

spa being eroded pH Up instructions. Test and restore

pH Down alkalinity and pH to proper

Total “A” levels.

NOTE: Most water chemistry problems can be resolved by the recommended solu-

tions above. Extreme chemical conditions may warrant draining and refilling the spa.

Stains or calcium deposits on the spa may require attention prior to refilling. Please

contact your dealer if you have further questions.

19

SPA SITUATIONS & SOLUTIONS

La page charge ...

Viking Plug-n-Play Spas Series Le manuel du propriétaire

Ce manuel convient également à

Viking Plug-n-Play Spas Series Le manuel du propriétaire

dans d''autres langues

Autres documents