E-Mu 1616m Le manuel du propriétaire

Quick Start Guide - Getting Started - 1

1 - Introduction

Thank you for purchasing the E-MU 1212M, E-MU 1616 or E-MU 1616M PCI digital audio system. We’ve designed this

E-MU Digital Audio System to be ﬂexible, intuitive and above all, to provide you with uncompromising sound quality. All three

systems provide high-end studio-quality, 24-bit/192kHz multi-channel recording and playback at a truly astounding price.

System Requirements

• Intel

®

or AMD

®

processor operating at 1 GHz or faster

• Intel, AMD or 100% compatible motherboard & chipset

• Windows XP (SP2), Windows 2000 (SP4), or x64

• 256 MB System RAM

• 900 MB of free hard disk space for full installation.

•Available PCI 2.1 compliant slot (Two slots needed for E-MU 1212M)

• XVGA Video (1024 x 768)

• CD-ROM/CD-RW or DVD-ROM drive required for software installation.

• Headphones or ampliﬁed speakers

Other applications may have higher system requirements or may require a microphone.

Package Contents

E-MU 1212M PCI

E-MU 1616 PCI E-MU 1616M PCI

• E-MU 1010 PCI card

• E-MU 0202 I/O Daughter card

• I/O Daughter card ribbon cable

• (2) mini MIDI cables

• E-MU Digital Audio System

Software/Driver Install CD-ROM

•Production Tools Software

Bundle CD-ROM

• This Quick Start Guide

• E-MU 1010 PCI card

• E-MU MicroDock

• EDI (E-MU Digital Interface) cable

• Universal Power Adapter

• MIDI Breakout Cable

• E-MU Digital Audio System Software/

Driver Install CD-ROM

•Prod. Tools Software Bundle CD-ROM

• This Quick Start Guide

• E-MU 1010 PCI card

• E-MU MicroDock M

• EDI (E-MU Digital Interface) cable

• Universal Power Adapter

• MIDI Breakout Cable

• E-MU Digital Audio System Software/

Driver Install CD-ROM

•Prod. Tools Software Bundle CD-ROM

• This Quick Start Guide

EMU QS(En).fm Page 1 Thursday, October 26, 2006 11:09 AM

2 - E-MU PCI Digital Audio System

Safety First!

As you install hardware components, observe the following general precautions to avoid damage to your equipment and

yourself.

•To avoid possible permanent damage to your hardware, make sure that all connections are made to the E-MU 1010

card and the MicroDock with the host computer’s power off.

Unplug the computer’s power cable to make sure that the computer is not in sleep mode

.

•Take care to avoid static damage to any components of your system. Internal computer surfaces, the E-MU 1010 PCI

board and the interfaces are susceptible to electrostatic discharge, commonly known as “static”. Electrostatic

discharge can damage or destroy electronic devices. Here are some procedures you can follow when handling

electronic devices in order to minimize the possibility of causing electrostatic damage:

•Avoid any unnecessary movement, such as scufﬁng your feet when handling electronic devices, since most

movement can generate additional charges of static electricity.

• Minimize the handling of the PCI card. Keep it in its static-free package until needed. Transport or store the board

only in its protective package.

• When handling a PCI card, avoid touching its connector pins. Try to handle the board by its edges only.

• Before installing a PCI card into your computer, you should be grounded. Use a ground strap to discharge any static

electric charge built up on your body. The ground strap attaches to your wrist and any unpainted metal surface

within your computer.

Getting More Information

Refer to the various online Help ﬁles and the Owner’s Manual (on CD) for detailed information on the E-MU Digital Audio

System and various software applications.

After Software Installation:

Click on the E-MU icon in the Windows SysTray to open PatchMix DSP, then click the

in the upper right corner to open the complete operation manual.

Technical Support

As the E-MU Digital Audio System expands, you’ll want to keep up with the latest software and new options for your E-MU

Digital Audio System. You can ﬁnd all of this—plus other helpful information—at

www.emu.com

. Refer to your Owner’s

Manual on CD for the technical support phone number.

?

EMU QS(En).fm Page 2 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 3

2 - Hardware Installation

Step 1: Prepare your computer

1. Turn off your computer and all peripheral devices.

2. Touch a metal plate on your computer to ground yourself and to discharge any static

electricity, and then unplug the power cord from the wall outlet.

3. Remove the computer cover.

4. Remove the metal bracket from one PCI slot.

If you have the E-MU 1212

m

system or are

installing the Sync Daughter Card you’ll need to remove the bracket from two PCI slots.

See the ﬁgure at left.

Step 2: Install the E-MU 1010 PCI card

1. Align the E-MU 1010 PCI card with the slot and press gently but ﬁrmly down into the slot

as shown in the ﬁgure opposite.

2. Do not force the E-MU 1010 card into the slot. Make sure that the gold ﬁnger connector

of the card is aligned with the PCI bus connector on the motherboard before you insert

the card into the PCI slot. If it doesn’t ﬁt properly, gently remove it and try again.

3. Secure the card to the slot using a screw (if necessary).

Metal

brackets

PCI slots

ISA slots

EMU QS(En).fm Page 3 Thursday, October 26, 2006 11:09 AM

4 - E-MU PCI Digital Audio System

Step 3: 1212M Owners - Install 0202 I/O Daughter Card

Note:

This step is for E-MU 1212M owners only. 1616/1616M owners, go on to Step 5

1. Connect the ribbon cable provided with the kit between the E-MU 1010 card and the

I/O Daughter card as shown in the ﬁgure at right. The cable is keyed so it cannot be

incorrectly inserted. Seat the connector ﬁrmly in the socket and arrange the cable

neatly.

2. Secure the E-MU 0202 I/O Daughter card into the slot next to the E-MU 1010 card,

using a second screw (if necessary).

3. Replace the cover to your computer.

4. Plug the power cord and your peripheral devices into your computer and turn on

your computer.

5. Go to Section 3 -

Software Installation

on page 6.

Note:

Step 4 is for owners of the optional Sync Card only.

Step 4: Sync Card Owners - Install Sync Daughter Card

1. Connect the ribbon cable provided with the kit between the E-MU 1010 card and the

Sync Daughter card as shown in the ﬁgure at right. The cable is keyed so it cannot be

incorrectly inserted. Seat the connector ﬁrmly in the socket and arrange the cable

neatly.

2. Secure the E-MU Sync Daughter card into the slot next to the E-MU 1010 card, using

a second screw (if necessary).

3. Replace the cover to your computer.

4. Plug the power cord and your peripheral devices into your computer and turn on

your computer.

5. Go to Section 3 -

Software Installation

on page 6.

0202 I/O Daughter Card

Optional Sync Daughter Card

EMU QS(En).fm Page 4 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 5

Step 5: Connecting the MicroDock to the E-MU 1010 Card

Connect the supplied network-type cable from the RJ-45 jack on the E-MU 1010 PCI card labeled “EDI” to the matching

connector labeled “EDI” on the MicroDock. The cable type is a standard CAT 5e network cable which is specially shielded to

prevent RF emissions. Contact E-MU Systems if you need a replacement cable.

CAUTION:

Do not connect the supplied

CAT 5e

cable to the Ethernet or network connector on your computer. Doing

so may result in permanent damage to either your computer, the E-MU 1010 or both.

Supplying Power to the MicroDock

The MicroDock is powered from the supplied +48VDC Adapter. Connect the Adapter to the jack marked +48VDC on the

back panel of the MicroDock. Turn the MicroDock on by turning the Headphone Volume control up.

EDI

48

VDC

+

-

+48V DC Adapter

1010 PCI Card

The Headphone

Volume Control is

also the Power Switch.

EMU QS(En).fm Page 5 Thursday, October 26, 2006 11:09 AM

6 - E-MU PCI Digital Audio System

3 - Software Installation

Installing and Uninstalling the E-MU 1010 Drivers and Applications

The ﬁrst time you restart your PC after installing the 1010 PCI card, you need to install the Patchmix DSP software and 1010 drivers.

Windows XP, Windows 2000, x64

(The software is not compatible with other versions of Windows.)

1. After you have installed your audio card, turn on your computer. Windows automatically detects your audio card

and searches for device drivers.

2. When prompted for the audio drivers, click the

Cancel

button.

3. Insert the E-MU software Installation CD into your CD-ROM drive.

If Windows AutoPlay mode is enabled for your CD-ROM drive, the CD starts running automatically. If not, from

your Windows desktop, click

Start

->

Run

and type

d:setup.exe

(replace

d:\

with the drive letter of your CD-ROM

drive). You can also simply open the CD and double-click

Setup.exe

.

4. The installation splash screen appears. Follow the instructions on the screen to complete the installation.

5. Choose “Continue Anyway” when you encounter the “Windows Logo Testing” warning screen.

6. When prompted, restart your computer.

Uninstalling all Audio Drivers and Applications

At times you may need to uninstall or reinstall some or all of the audio card's applications and device drivers to correct

problems, change conﬁgurations, or upgrade outdated drivers or applications. Before you begin, close all audio card

applications. Applications still running during the uninstallation will not be removed.

1. Click

Start

->

Settings

->

Control Panel

.

2. Double-click the

Add/Remove Programs

icon.

3. Click the

Install/Uninstall

tab (or

Change or Remove Programs

button).

4. Select the E-MU 1010 PCI card entry, or the application entry and then click the

Add/Remove

(or

Change/Remove

) button.

5. In the

InstallShield Wizard

dialog box, select the

Remove

option.

6. Click the

Yes

button.

7. Restart your computer when prompted.

8. You may now re-install existing or updated E-MU 1010 PCI card device drivers or applications.

EMU QS(En).fm Page 6 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 7

4 - E-MU 1010 PCI Card & Interface

The E-MU 1010 PCI card is the heart of the system and contains E-MU’s powerful E-DSP chip. The powerful hardware DSP

on this card leaves more power free on your CPU for additional software plug-ins and other tasks.

Connections

EDI

Connects to

Audio Dock

via EDI Cable

S/PDIF

In/Out

ADAT

or S/PDIF

Optical

In/Out

EDI

Connector

Connects to the MicroDock using EDI (E-MU Digital Interface) cable. This cable provides

a two-way data link between the E-MU 1010 and the MicroDock.

S/PDIF

Digital

Audio

Input &

Output

Each RCA phono jack carries two channels of digital audio. S/PDIF digital I/O can be used

for the reception and/or transmission of digital data from external digital devices such as

a DAT machine, an external analog-to-digital converter or an external signal processor

equipped with digital inputs and outputs. The embedded clock contained in the input

data stream can be used as a clock source for the 1010.

The S/PDIF out can be conﬁgured in either Professional or Consumer mode, always with

24-bits of resolution.

Important:

S/PDIF I/O is disabled on the 1010 PCI when the MicroDock is connected.

ADAT

®

Optical

Digital

Input &

Output

The ADAT optical connectors transmit and receive 8 channels of 24-bit audio using the

ADAT type 1 & 2 formats (at 44.1kHz or 48kHz). The embedded clock contained in the

input data stream can be used as a clock source for the 1010. The ADAT optical ports can

also be switched to carry optical S/PDIF.

ADAT can also be transmitted and received at 96kHz or 192kHz using the S/MUX

standard which encodes the extra data onto multiple channels.

Important:

ADAT I/O is disabled on the 1010 PCI when the MicroDock is connected.

EMU QS(En).fm Page 7 Thursday, October 26, 2006 11:09 AM

8 - E-MU PCI Digital Audio System

5 - The E-MU 0202 I/O Daughter Card

The I/O daughter card provides one pair of 24-bit balanced analog inputs and one pair of 24-bit balanced analog outputs,

plus MIDI in and out. The I/O daughter card provides the analog inputs, outputs, and MIDI interface for E-MU digital audio

systems which don’t include the MicroDock. The I/O Daughter card takes up one extra space on the back panel of your

computer, and connects to the E-MU 1010 PCI card via an internal 40-pin ribbon cable.

Connections

Left / Right

Line Inputs

Left / Right

Line Outputs

MIDI

In/Out

Analog Inputs

and Outputs

The inputs can be connected to any line level stereo signal from a

keyboard, CD-player, cassette deck, etc. (The analog inputs are assigned to

mixer strips in the PatchMix DSP mixer application.)

The outputs can feed any line level input such as a mixing board, the

auxiliary input on your stereo, or a set of powered speakers.

Either TRS balanced or TS unbalanced cables can be used. Balanced cables

provide better noise immunity and +6dB higher signal level. The output

line level can be set to accommodate the consumer -10dBV standard, or

the pro audio +4 dBu standard in the I/O screen of the Session Settings

dialog box.

MIDI In/Out

The MIDI input and output port can be assigned in your speciﬁc MIDI

application. Connect the MIDI adapter cable that came with your I/O

Daughter card to the mini-DIN connectors on the card. The supplied MIDI

adapter cables convert the mini-DIN to standard DIN connectors used on

most keyboards and synthesizers.

EMU QS(En).fm Page 8 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 9

6 - MicroDock Connections

EDI

In

1L

1R

2L

2R

3L

3R

2L

2R

Out

1L

1R

Phono

Gnd

2L

2R

1

2

Out

48

VDC

+

-

MIDI Cable

3

Basic

Connections

T

u

rn

tab

l

e

**

MIDI 1

MIDI In

MIDI Out

Powered

Desktop

Speakers

MIDI Synthesizer

Mixer

&

Speakers

Audio

from

Synthesizer

Audio

to

Monitors

Connect

Desktop

Speakers to

1/8" jacks

1010 PCI

Card

AC Adapter

S

t

e

r

e

o

In

Out

* Note: Line Inputs 2L/2R and Phono 2L/2R cannot be used at the same time.

EMU QS(En).fm Page 9 Thursday, October 26, 2006 11:09 AM

10 - E-MU PCI Digital Audio System

Line

A

Mic

-15

0

Line -

Mic -

Clip

+50

Line

B

Mic

+65

-15

0

48V

+50

+65

S/PDIF

In

Out

-3

-6

-12

-20

SL

Clip

-3

-6

-12

-20

SL

Off

Instrument

Mic

Stereo

Headphones

On/Off

& Phone Volume

Front Panel

Analog Connections

Use the center

Phone Jack for

High Impedance

instruments such

as electric guitar

or bass.

Use the 3-pin XLR jack

for Low Impedance

microphones.

EMU QS(En).fm Page 10 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 11

MIDI 1

S/PDIF

(Coax)

ADAT

(Optical)

MIDI Keyboard

EMULATOR

PRESET

SAMPLE

SEQUENCER

PAGE

LEVEL

PRESET SELECT

REAL TIME CONTROLLERS

ASSIGNABLE KEYS

ENTER

EXIT

RETURN

0.987654321

Digital Connections

DAT or CD

Digital Audio Device with S/PDIF

(8 more analog inputs & outputs)

Coaxial

Optical

I

VOLUME

O

TRANSPOSE DIGITAL PROCESSINGSAMPLE MANAGEMENT

SAMPLE

PRESET

MASTER/GLOBAL

MULTIMODE

PRESET MANAGEMENT DYNAMIC PROCESINGPRESET DEFINITION

DRIVE SELECT LOAD SAVE AUDITION TRIGGER MODE

ESCAPE

MIDI

ENTER

DEC/NO

INC/YES

ABC

JKL

TUV

DEF

MNO

WXY

QZ

GHI

PRS

TRIGGERS

123

456

789

0

MIDI Sound Module

In

Out

In

MIDI 2

Out

In

MIDI Out

In

Out

MIDI In

Out

In

Out

MIDI In

1 2 3 4 5 6 7 8

External A/D - D/A Converter

Audio Outs

EMU QS(En).fm Page 11 Thursday, October 26, 2006 11:09 AM

12 - E-MU PCI Digital Audio System

7 - MicroDock & MicroDock M

The MicroDock connects to the E-MU 1010 PCI card via the EDI cable. The front of the MicroDock provides 2 balanced mic/

line preamp inputs, 8 channels of ADAT digital input/output, stereo S/PDIF digital input/output, and a stereo headphone

output with volume control/power switch.

Front Panel Connections

Line

A

Mic

-10

+20

Line -

Mic -

Clip

+25

Line

B

Mic

+55

-10

+20

48V

+25

+55

S/PDIF

In

Out

-3

-6

-12

-20

SL

Clip

-3

-6

-12

-20

SL

Off

1/4" Line

Level Input

Phantom

Power

On/Off

Signal

Meters

Clip

Soft

Limit

Input Gain

Controls

Headphone

Output

Headphone Volume

/ Power Switch

S/PDIF

Coaxial I/O

ADAT

Optical I/O

Insert XLR Plug

for Mic Level

0dB to +65dB Gain

-15dB to +50dB Gain

EMU QS(En).fm Page 12 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 13

Preamp Section

The front panel mono Mic/Line inputs A & B can be used as balanced microphone inputs, hi-Z

guitar pickup inputs, or balanced line level inputs. The Neutrik combination jack accepts

microphones using a standard XLR connector or line level/hi-Z inputs using a 1/4 inch TRS phone

plug.

Warning:

Some microphones cannot tolerate phantom power and may be damaged. Check the

microphone’s speciﬁcations and requirements before using phantom power.

S/PDIF Digital

Audio Input &

Output

Each RCA phono jack carries two channels of digital audio. S/PDIF digital I/O can be used for the

reception and/or transmission of digital data from external digital devices such as a DAT machine, an

external analog-to-digital converter or an external signal processor equipped with digital inputs and

outputs. The word clock contained in the input data stream can be used as a clock source.

The S/PDIF output can be conﬁgured in either Professional or Consumer mode (always 24-bit

resolution). The S/PDIF input/outputs support all the PatchMix DSP sample rates: 44.1kHz, 48kHz,

88.2kHz, 96kHz, 176.4kHz & 192kHz.

ADAT

®

Optical

Digital Input &

Output

• The ADAT optical connectors transmit and receive 8 channels of 24-bit audio using the ADAT

type 1 & 2 formats (at 44.1kHz or 48kHz).

• The word clock contained in the input data stream can be used as a clock source.

• The ADAT optical ports can also be switched to carry optical S/PDIF.

• ADAT can also be transmitted and received at 88, 96, 176, or 192kHz using the S/MUX standard.

S/MUX provides 4 audio channels at 88.2/96 and 2 audio channels at the 176/192 sample rates.

Headphone

Output &

Volume Control

The headphone output drives standard stereo headphones and the adjacent volume control sets

the listening level. This output is permanently connected to the Monitor Output in PatchMix DSP.

The headphone output uses a high-current version of the high-quality output ampliﬁers used on

the other channels. For this reason it has a very clean signal that can be used as another stereo

output if you need it.

EMU QS(En).fm Page 13 Thursday, October 26, 2006 11:09 AM

14 - E-MU PCI Digital Audio System

Rear Panel Connections

Line Level

Analog Inputs

Four balanced 24-bit, line-level, analog inputs are provided (Stereo 1-2). These can be used to

input any line level signal such as a keyboard, CD-player, cassette deck, etc. (The analog inputs are

assigned to mixer strips in the PatchMix DSP mixer application.) Input line level can be set to

accommodate the consumer -10dBV standard, or the pro audio +4 dBu standard in the I/O screen

of the Session Settings dialog box.

Either TRS balanced or TS unbalanced cables can be used. Balanced cables provide better noise

immunity and +6dB higher signal level, but standard mono instrument cables also work well.

EDI

In

1L

1R

2L

2R

3L

3R

2L

2R

Out

1L

1R

Phono

Gnd

2L

2R

1

2

Out

48

VDC

+

-

MIDI Cable

3

4 Balanced Line Level Inputs

(configured as 2 stereo pairs)

Turntable Inputs

(tied to line input 2)

Turntable

Ground

Alternate Outputs6 Balanced Line Level Outputs

(configured as 3 stereo pairs)

MIDI Port

Connector

48 Volt DC

Power Inpu

t

Connect to

1010 PCI Card

(same as outputs 1-3)

EMU QS(En).fm Page 14 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 15

Line Level

Analog

Outputs

Six balanced 24-bit, line-level, analog outputs are provided (Stereo 1-3). Output pair 1 is

designated as the Monitor Output and is normally fed by the monitor output of the PatchMix DSP

mixer application. All the analog outputs can be freely assigned in the mixer application.

Special anti-pop circuitry mutes the analog outputs when power is turned on or off.

Like the analog line inputs, either TRS balanced or TS unbalanced cables can be used.

Balanced cables provide better noise immunity and +6dB higher signal level, but standard mono

instrument cables also work well.

The output line level can be set to accommodate the consumer -10 dBV standard, or the pro audio

+4 dBu standard in the I/O screen of the Session Settings dialog box.

Turntable

Inputs &

Ground Lug

The RCA turntable inputs feed an RIAA equalized phono preamp designed to accept moving

magnet type phono cartridges. The turntable inputs share line level inputs 2L and 2R. Inserting a

plug into Line Input 2 disconnects the phono preamp from that channel. Connect the ground lead

from your turntable to the turntable ground lug to prevent hum.

MIDI 1& 2

In/Out

Attach the supplied MIDI Breakout cable to the MIDI Port connector on the rear of the MicroDock.

MIDI input and output ports allow you to interface any type of MIDI equipment such as keyboards,

effect units, drum or guitar controllers. The MIDI drivers were installed when you installed your

Patchmix DSP software and the MIDI ports will appear in your system control panel under “Sounds

and Audio Devices”.

Alternate

Outputs

These stereo mini-phone (3.5mm) jacks duplicate the line level outputs 1-3. These line level

outputs are designed for easy interface to powered computer speakers.

EDI Connector

Connects the MicroDock to the E-MU 1010 PCI card using CAT 5e type computer cable. The cable

supplied with the MicroDock is specially shielded to prevent unwanted RF emissions.

EMU QS(En).fm Page 15 Thursday, October 26, 2006 11:09 AM

16 - E-MU PCI Digital Audio System

8 - The E-MU Sync Daughter Card (optional)

The optional Sync Daughter card provides Word Clock in and out, SMPTE (LTC) in and out and an additional MIDI output

for transmitting MIDI Time Code (MTC). MTC is a special rendering of SMPTE that can be transmitted over MIDI cables.

Note: When the Sync Card is installed, MIDI 2 on the MicroDock is disabled. (MTC is using the MIDI port.)

Word Clock is a standard means of synchronizing two or more pieces of digital equipment at the system sample rate

(44.1kHz, 48kHz, 96kHz, or 192kHz). To avoid data corruption, digital equipment MUST be synchronized to each other.

Recording equipment can also be synchronized using SMPTE or MTC sync so that two audio recorders or an audio and

video recorder can lock together as a single machine. For more information, please refer to your Owner’s Manual (on CD).

Connections

Word Clock

Inputs and

Outputs

Word Clock In: Receives word clock (sample clock) from another digital device such

as a digital video deck, digital recorder or digital mixer.

Word Clock Out: Sends word clock (sample clock) to another digital recorder. Word

clock is always output, whether it is generated by the internal clock or passed

through from the word clock input.

SMPTE In/Out

The SMPTE Input converts incoming SMPTE longitudinal time code (LTC) to MIDI Time

Code (MTC) and passes this information to the host computer to be used by a

sequencer or audio recorder application. When your computer application is the

“Master”, MTC generated by the computer application is converted into SMPTE and

sent out to another SMPTE device such as another audio recorder to synchronize it

with the sequencer.

MTC Out

This output transmits MIDI Time Code to another computer or audio recorder. The

source of the MTC can be from the sequencer or SMPTE in.

EMU QS(En).fm Page 16 Thursday, October 26, 2006 11:09 AM

Quick Start Guide - Getting Started - 17

Copyright

Information in this document is subject to change without notice and does not represent a commitment on the part

of E-MU Systems, Inc. No part of this manual may be reproduced or transmitted in any form or by any means, electronic

or mechanical, including photocopying and recording, for any purpose without the written permission of E-MU Systems,

Inc. The software described in this document is furnished under a license agreement and may be used or copied only

in accordance with the terms of the license agreement. It is against the law to copy the software on any other medium

except as speciﬁcally allowed in the license agreement. The licensee may make one copy of the software for backup

purposes only.

E-MU is a registered trademark of E-MU Systems, Inc. in the United States and/or other countries.

Version 1.82,

April 2006

The use of the WEEE symbol indicates that this product may not be

treated as household waste. By ensuring this product is disposed of

correctly, you will help protect the environment. For more detailed

information about the recycling of this product, please contact your

local authority, your household waste disposal service provider or

the shop where you purchased the product.

EMU QS(En).fm Page 17 Thursday, October 26, 2006 11:09 AM

18 - E-MU PCI Digital Audio System

EMU QS(En).fm Page 18 Thursday, October 26, 2006 11:09 AM

Guide de mise en œuvre - Prise en main - 19

1 - Introduction

Merci d’avoir acheté le système audio numérique E-MU 1212M, E-MU 1616 ou E-MU 1616M. Nous avons conçu ce

système audio numérique E-MU aﬁn qu’il soit logique et intuitif et qu’il vous offre surtout une qualité sonore irréprochable.

Les trois systèmes audio offre une qualité studio professionnel, un enregistrement et une lecture multicanaux 24 bits/

192 kHz pour un prix incroyablement réduit.

Conﬁguration requise

•Processeur Intel

®

ou AMD

®

à 1 GHz ou plus rapide.

• Carte mère et jeu de puces Intel, AMD ou 100 % compatible.

• Windows XP (SP2), Windows 2000 (SP4), or Windows XP x64

• 256 Mo de RAM

• 900 Mo d’espace disque disponible pour une installation complète.

• Emplacement disponible compatible PCI 2.1 (deux emplacements sont nécessaires pour E-MU 1212M et 1616M)

•Vidéo XVGA (1024 x 768)

• Lecteur de CD-ROM/CD-RW et DVD-ROM nécessaire pour l’installation du logiciel.

• Casque ou haut-parleurs ampliﬁés.

D’autres applications peuvent avoir des exigences plus élevées ou nécessiter un microphone.

Contenu du coffret

E-MU 1212

m

PCI E-MU 1616 PCI E-MU 1616

m

PCI

• Carte PCI E-MU 1010

• Carte ﬁlle E/S E-MU 0202

• Câble en nappe pour carte ﬁlle E/S

• (2) câbles mini MIDI

• CD d’installation des logiciels/Drivers

Digital Audio Systems

• CD-ROM d’outils de production

• Guide de démarrage rapide

• Carte PCI E-MU 1010

•MicroDock

• Câble EDI (E-MU Digital Interface,

interface numérique E-MU)

• Câble de conversion

• Adapteur de +48VDC

• CD d’installation des logiciels/Drivers

Digital Audio Systems

• CD-ROM d’outils de production

• Guide de démarrage rapide

• Carte PCI E-MU 1010

•MicroDock M

• Câble EDI (E-MU Digital Interface, interface

numérique E-MU)

• Câble de conversion

•

Adapteur de +48VDC

• CD d’installation des logiciels/Drivers Digital

Audio Systems

• CD-ROM d’outils de production

• Guide de démarrage rapide

EMU GS(Fr).fm Page 19 Thursday, October 26, 2006 1:15 PM

20 - Système audio numérique E-MU PCI

Consignes de sécurité

Lors de l’installation de composants matériels, respectez les précautions générales ci-dessous pour éviter de vous blesser ou

d’endommager le matériel.

• Pour éviter d’endommager de manière irréversible votre matériel, vériﬁez que toutes les connexions sont effectuées sur la

carte E-MU 1010 et sur MicroDock lorsque l’ordinateur hôte est hors tension.

Débranchez le câble d’alimentation de

l’ordinateur pour vous assurer que l’ordinateur n’est pas en mode veille.

• Assurez-vous que les composants de votre système ne subissent pas de dégâts liés à l’électricité statique. Les surfaces

internes de l’ordinateur, la carte PCI E-MU 1010 et les interfaces sont susceptibles de subir des décharges électrostatiques,

fréquemment appelées « statiques ». Les décharges électrostatiques peuvent endommager ou détruire les appareils

électroniques. Vous trouverez ci-dessous des procédures à suivre lors de la manipulation d’appareils électroniques qui vous

permettront de réduire le risque de dégâts électrostatiques.

• Evitez tout mouvement inutile. Evitez par exemple de traîner les pieds lorsque vous manipulez des appareils électroniques,

car les mouvements génèrent de l’électricité statique supplémentaire.

• Réduisez la manipulation de la carte PCI à un minimum. Conservez-la dans son emballage antistatique jusqu’à ce que vous

en ayez besoin. Transportez ou conservez la carte dans son emballage protecteur.

• Lorsque vous manipulez la carte PCI, évitez de toucher les broches. Essayez de manipuler la carte en la tenant par les

bords.

•Avant d’installer une carte PCI dans votre ordinateur, vous devez être relié à la terre. Utilisez un conducteur de terre pour

décharger votre organisme de tout excès de charge électrostatique. Le conducteur de terre s’attache au poignet et à toute

surface métallique dépourvue de peinture de votre ordinateur.

Pour plus d’informations

Reportez-vous aux différents ﬁchiers d’aide en ligne et au manuel de l’utilisateur (sur CD) pour obtenir des informations

détaillées sur le système audio E-MU et sur les différentes applications logicielles.

Après l'installation logicielle :

Cliquez sur l'icône E-MU du menu déroulant des applications Windows et ouvrez

PatchMix DSP. Cliquez ensuite sur l'icône dans le coin supérieur droit pour ouvrir le mode d'emploi complet.

Assistance technique

Dans la mesure où le système audio numérique E-MU ne cesse de se développer, vous voudrez sûrement suivre les évolu-

tions logicielles et les dernières options de votre système audio numérique E-MU. Vous trouverez toutes ces informations, et

bien d’autres encore, sur le site

www.emu.com

. Reportez-vous au manuel de l’utilisateur sur CD pour obtenir le numéro

de téléphone de l’assistance technique.

?

EMU GS(Fr).fm Page 20 Thursday, October 26, 2006 1:15 PM

La page charge ...

E-Mu 1616m Le manuel du propriétaire

Ce manuel convient également à

E-Mu 1616m Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents